Barco XLM HD30 User guide
advertisement
R5976790/00
09/07/2004
Communicator
User guide
Events Edition
R9806075
Barco nv Events
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.89.70
Fax: +32 56.36.88.24
E-mail: [email protected]
Visit us at the web: www.barco.com
Printed in Belgium
Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this publication; these changes are incorporated in new editions of this publication.
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee.
On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of compliant, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period.
If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties guaranteed in writing or due to the intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in the this manual must be complied with by the customer.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufactures.
Table of contents
TABLE OF CONTENTS
1. Introduction ..........................................................................................3
2. Software installation and start up...............................................................5
3. Projector Connection ..............................................................................7
4. Projector Setup.................................................................................... 15
5. Adjustment ......................................................................................... 19
R5976790 COMMUNICATOR 09/07/2004 1
Table of contents
6. Projector Configuration ......................................................................... 39
7. Projector Status ................................................................................... 45
8. Version Info ........................................................................................ 53
Glossary................................................................................................ 55
Index .................................................................................................... 57
2 R5976790 COMMUNICATOR 09/07/2004
1. Introduction
1. INTRODUCTION
1.1
General introduction
XLM configuration tool
A uniquely powerful and easy to use configuration program for the Barco XLM projector, Communicator,
Events Edition, provides all of the tools necessary for the total projector set-up and control. A comprehensive array of easy to access menu pages provide control of the XLM’s digital input, output and screen display via a combination of simple buttons and WYSIWYG displays.
Quick and Easy configuration
Via clearly indicated tab pages for control of Projector Connection, Configuration.
Total Control
Of the Projector Input selection, alignment and switching, Screen Display output.
With extensive projector Status indication, Lamp run-time register.
About this manual
This User Guide provides detailed information about the Communicator, Events Edition, features. This guide is designed to be a reference tool in your everyday work with the Communicator.
The following icons are used in the manual :
Caution
Warning
Info, term definition. General info about the term.
Note, gives extra information about the described subject.
Tip, gives extra advice about the described subject.
Typography:
• Clickable menu items or buttons are indicated in bold, e.g. Open
• A menu window is indicated in italic, e.g. Measure CLO.
• Step related notes, tips, warnings or cautions are printed in italic.
• Procedure related notes, tips, warnings or cautions are printed in bold between 2 lines preceding by the corresponding icon.
R5976790 COMMUNICATOR 09/07/2004 3
1. Introduction
4 R5976790 COMMUNICATOR 09/07/2004
2. Software installation and start up
2. SOFTWARE INSTALLATION AND START
UP
Overview
•
•
•
•
Removing the Communicator software
2.1
Required Configuration
PC requirements
• Windows 2000, Windows NT, Win95, Win98 and WinME
• 266 MHz, 64 MB Ram
• Minimum disk space : 30 MB
2.2
Installing the Software
How to install
1. Insert the CD-ROM in the CD-ROM drive.
2. Is the AutoPlay active on your PC.
If no, from within the Windows environment go to the Start Menu. Choose Run... from the menu and proceed with the next steps.
3. Open windows explorer.
4. Select the CD-ROM drive.
5. Double click ’setup.exe’ file.
6. Press OK to run the installation.
Follow the instruction of the Installation shield.
7. The setup program will ask you for to specify an install directory. You can accept the default location or browse to a specific directory. Click NEXT.
8. Read the Licence agreement and click Yes to continue the installation.
The program will be installed on the PC system and the user will be prompted to ask a icon will be placed on the desktop .
R5976790 COMMUNICATOR 09/07/2004 5
6
2. Software installation and start up
2.3
Upgrading the Software
How to update
1. Download or copy the update zip file locally.
2. Unzip the update file in the communicator install directory..
3. Run Setup.exe.
The windows install shield opens.
4. Click on Next to continue.
The install shield check the PC for an old version of the Communicator software.
A selection window will be displayed.
5. Select the radio button in front of Upgrade Software to version xxxx.
6. Click now Next.
The actual version on the PC will be replaced by the new one.
See Communicator release notes to find out the differences with previous versions.
2.4
Removing the Communicator software
How to remove
1. Run Setup.exe.
The windows install shield opens.
2. Click on Next to continue.
A selection window will be displayed.
3. Select the radio button in front of Delete the current installed software.
4. Click on Next.
The software will be removed from the PC.
R5976790 COMMUNICATOR 09/07/2004
3. PROJECTOR CONNECTION
Overview
•
•
•
•
Disconnecting from the XLM projector
•
Controlling one or more projectors
•
3. Projector Connection
3.1
Introduction
Overview
The Communicator can be connected to the XLM projector in one of the following ways:
• Via an Ethernet connection (network connection)
• Via a serial connection
3.2
Network connection
Overview
•
•
•
•
•
•
•
Selecting the Read-Write projector
3.2.1
Introduction
Overview
Up to 8 projectors can be added to the list of projectors, and these 8 projectors can be controlled all at the same time. The Communicator can only see the settings of one projector, the master, but it can write to all projectors at the same time. The master projector will be indicated as RW, what means “read/write” projector. All others have the indication W, what means “write”.
To control these projectors, set up first a hardware connection and add the projectors to the list of projectors.
3.2.2
Hardware connection
Possibilities
Connect port 1 or port 2 to a LAN by using a straight cable or a crossed cable. The connection is a 10/100 baseT.
R5976790 COMMUNICATOR 09/07/2004 7
3. Projector Connection
BI-DIRECTIONAL
PUSH
2
3
1
CTRL 3
UNI-DIRECTIONAL
PUSH
2
3
1
CTRL 2 CTRL 1 PORT 1 PORT 2
HARDWIRED REMOTE 10/100 BASE T
WIRELESS REMOTE
RS232/422 IN
RS232/422 OUT
SERIAL NETWORK
Image 3-1
Ethernet connection
The projector must have an IP address and the IP address of the connected PC must be within the same range of IP addresses.
3.2.3
Add new projector
What can be done ?
Up to 8 projectors can be added to the list. Once added, this projector can be controlled with the Communicator.
How to add ?
1. Right click in the projector list pane.
A pop-up window appears (image 3-2)
2. Select Add projector.
The projector settings window opens. (image 3-3)
3. Click in the Projector Name input field and fill out a name for the projector.
Note: The projector name should be unique.
4. Click in the left IP Address input field and enter the IP address of the projector.
Note: An address contains 4 octets with a maximum value of 255.
5. Click on the Port Number drop down box and select the port.
Note: The combination IP address and port number must be unique.
Default 43680.
It is possible to enter the same IP address with a different port number. That means that the same projector can be accessed by 2 different Communicator via a different port.
6. If you want to add a short cut for this projector, click on the drop down box and select the desired short cut.
Note: The short cut must be unique for each projector.
Short cuts for F1 to F8 can be associated with the projector. When a short cut is associated to a projector, this projector can be selected (as read/write) from any pane in the software.
7. Click OK to add the projector.
8 R5976790 COMMUNICATOR 09/07/2004
3. Projector Connection
Image 3-2
Add projector
Image 3-3
Projector settings
3.2.4
Delete a projector
What can be done ?
Any projector in the list can be deleted out of the list.
How to delete ?
1. Right click on the projector which has to be removed.
A pop-up menu appears. (image 3-4)
2. Click on Delete.
The projector will be removed from the list.
R5976790 COMMUNICATOR 09/07/2004 9
3. Projector Connection
Image 3-4
Delete projector
3.2.5
Edit projector settings
How to edit
1. Right click on a projector name. (image 3-5)
2. Click on Edit.
The projector settings window opens. (image 3-6)
3. To change the name, click in the input field next to Projector Name and enter the new name.
Note: The projector name must be unique in the list of projectors.
4. To change the IP address, click in the input field next to IP address and change to the new value.
5. To change the port number, click on the drop down box next to Port Number and select the desired port.
Note: The combination IP address and Port Number must be unique.
6. To change the short cut association, click on the drop down box next to Shortcut Key and select the new short cut.
Note: The shortcut should be unique in the list.
Image 3-5
Edit projector settings
10
Image 3-6
Edit projector settings window
R5976790 COMMUNICATOR 09/07/2004
3. Projector Connection
3.2.6
Making connection
What should be done ?
Before a connection can be made with one or more projectors, these projectors should be check.
Making connection
1. Check first the projectors to which the Communicator should make a connection (1). (image 3-7)
2. Click on Connect (2).
When a connection is possible, the connection status will change from Disconnected to Connected (4).
All other tabs of the GUI become enabled and accessible.
Image 3-7
Making a connection
3.2.7
Selecting the Read-Write projector
Read-Write projector
The read-write projector is the projector from which the settings are loaded (monitored) in the Communicator software. These settings can be adapted and used to control all write projectors.
How to select ?
1. Click on the name of the projector which must become the read-write projector.
The background changes to dark grey.
3.3
Serial Network Connection
Physical connection
Connect a serial cable from PC to the RS232IN connector of the projector.
R5976790 COMMUNICATOR 09/07/2004 11
3. Projector Connection
BI-DIRECTIONAL
PUSH
2
3
1
CTRL 3
UNI-DIRECTIONAL
PUSH
2
3
1
CTRL 2 CTRL 1 PORT 1
PORT 2
HARDWIRED REMOTE 10/100 BASE T
WIRELESS REMOTE
RS232/422 IN RS232/422 OUT
SERIAL NETWORK
Image 3-8
Serial connection, physical location
Necessary parts
Straight serial cable
Software connection
1. Click on the tab button Serial Connection.
The tab page opens.
2. Set up the communication port by clicking on the drop down menu (1) and selecting the correct port.
3. Click on the bits per second drop down menu (2) to set up the desired baud rate.
4. Click on the up or down arrows in the projector address menu (3) to set up the desired address.
Or, click on the projector address input field and enter the desired address with the keyboard.
5. Click on Connect
When a connection is possible, connected will be indicated.
All other tabs will become enabled and accessible.
3.4
Disconnecting from the XLM projector
Software disconnection
1. Click on Disconnect. (image 3-9)
A disconnect indication will be displayed. (image 3-10)
Image 3-9
Disconnecting from projector
12
Image 3-10
Disconnected from projector
R5976790 COMMUNICATOR 09/07/2004
3. Projector Connection
3.5
Controlling one or more projectors
To control only one projector
1. Go to Connections, select Network connections and check only those projector you want to control.
Now it is possible to fully control these projector.
To control different projectors at the same time.
1. Go to Connections, select Network connections and check those projectors you want to control at the same time.
All checked projectors can now be controlled.
3.6
Shortcut keys
How to use the shortcut keys ?
Within each pane a projector can be selected by its shortcut.
The selected projector becomes the RW (Read-Write) projector and its name will be displayed in the title bar of the window.
Example:
When e.g. F3 is pressed, Demo 3 projector becomes RW.
Image 3-11
F3 selected
The name Demo 3 appears in the title bar of any pane.
R5976790 COMMUNICATOR 09/07/2004 13
3. Projector Connection
14 R5976790 COMMUNICATOR 09/07/2004
4. PROJECTOR SETUP
Overview
•
•
•
•
•
•
4.1
Control Interface Set up
Overview of the layout
All the settings and setups are visualized in this control interface.
The following is visualized from left to right:
• layout file
• Input files per source
• Name projector with projector logo
• Shutter open or closed
• Lamp on or off : indicated by a light beam. Black means that the lamp is off.
• Test pattern on/off + the name of the test pattern or preview
4. Projector Setup
Image 4-1
Setup interface
4.2
Internal Patterns Shortcuts
What can be done ?
A predefined pattern can be set immediately on the projection screen and cleared again.
R5976790 COMMUNICATOR 09/07/2004 15
4. Projector Setup
To set a pattern
1. Click on one of the predefined icons. (image 4-2)
The selected pattern will be displayed by the projector when the lamp is on and the shutter is open.
The following patterns are available:
- Full screen white
- Full screen green
- Color bars
- Focus
- Outline
- Full screen red
- Full screen blue
- CheckerBoard
- Convergence
- Hatch
Image 4-2
Internal patterns
Command will be send to all write projectors
To clear a test pattern
1. Just click on the Clear button.
Command will be send to all write projectors
4.3
Lamp ON/OFF
What can be done ?
The projection lamp can be switched ON or OFF using the buttons in the software.
16 R5976790 COMMUNICATOR 09/07/2004
4. Projector Setup
Toggling the lamp status
1. Press lamp on icon ( ).
The lamp will be switched ON. The interface will indicate lamp ON.
2. Press lamp off icon ( ).
The lamp will be switched OFF. The interface will indicate lamp OFF.
Command will be send to all “write” projectors
4.4
Shutter Open or Close
What can be done ?
With this function you have full control over the shutter setting. With a single click it is possible to open or close the shutter.
How to toggle the shutter ?
1. Click on one of the shutter icons to open or close the shutter. (image 4-3)
The status of the shutter is indicated on the interface window.
To open the dowser, click on the open icon ( ).
To close the dowser, click on the close icon ( ).
Image 4-3
Shutter
Command will be send to all “write” projectors
4.5
Lens shift
What can be done ?
As the lenses for the XLM projector are motorized, it is possible to adjust these lenses via the Communicator.
The image can be shifted horizontally and vertically.
R5976790 COMMUNICATOR 09/07/2004 17
4. Projector Setup
How to shift the image ?
2. To shift the image vertically, click on the up and down red arrow under Lens shift.
Image 4-4
Lens shift
Command will be send to all “write” projectors
4.6
Lens Focus
What can be done ?
As the lenses for the XLM projector are motorized, it is possible to focus these lenses via the Communicator.
How to focus ?
1. To focus the image, click on the up and down red arrow under Lens Focus. (image 4-5)
Click until the correct focus is obtained.
Image 4-5
Lens focus
Command will be send to all “write” projectors
18 R5976790 COMMUNICATOR 09/07/2004
5. Adjustment
5. ADJUSTMENT
Overview
•
•
•
•
•
•
•
•
5.1
General introduction
Overview
With the XLM it is possible to connect up to four sources which can be mixed to one image. Each source is displayed in a separate window on which z-ordering is possible. The window size, timings and other settings can be set up for each source independently.
The result image is internally connected to the projector.
Window
A window represents the active area of an input source.
Layout
A layout is a collection of windows. These windows are placed on a certain position within the screen.
5.2
Create a new layout
How to create
1. Click on Layout file on the menu bar (1). (image 5-1)
The menu drops down.
2. Select Open(1).
An overview window with the existing layout files will be displayed (2).
3. Select a file out of the list (3) and click Open (4) .
The selected layout will be loaded (5).
The selected layout will be loaded on all “write” projectors if this file exists locally on that projector.
4. Change this layout to the desired one.
5. Save this layout into a new file by selecting Layout file → Save as. (image 5-2)
The current active file will be saved to all “write” projectors.
R5976790 COMMUNICATOR 09/07/2004 19
5. Adjustment
6. Click in the Filename input field and enter a new name for the layout. (image 5-3)
7. Click on Save.
The new layout will be saved.
20
Image 5-1
Create new layout
Image 5-2
Save as layout
Image 5-3
R5976790 COMMUNICATOR 09/07/2004
5. Adjustment
5.3
Edit an existing layout
How to edit
1. Click on Layout file on the menu bar.
The menu drops down.
2. Select Open.
An overview window with the existing layout files will be displayed.
3. Select the file you want to edit out of the list and click Open.
The selected layout will be loaded. If this file exists on the other “write” projectors, the layout will be loaded on these projectors too.
4. Edit the layout.
5. Save the layout by selecting Layout file → Save. (image 5-4)
The layout will overwrite the exiting one.
The current active file will be saved on all “write” projectors.
Image 5-4
Save layout
5.4
Renaming a layout
How to rename
1. Click on Layout file on the menu bar. (image 5-5)
The menu drops down.
2. Select Rename(1).
The layout file selection window opens (2).
3. Select the layout file you want to rename (3).
4. Click on Rename (4).
The rename window opens (5).
5. Click in the filename input field (6) and enter a new name for the layout.
6. Click on OK to rename (7).
The rename will be executed on all “write” projectors if the file exists on the “write” projector.
R5976790 COMMUNICATOR 09/07/2004 21
5. Adjustment
Image 5-5
Rename layout file
5.5
Deleting a layout
How to delete
1. Click on Layout file on the menu bar. (image 5-6)
The menu drops down.
2. Select Delete (1).
The layout file selection window opens (2).
3. Select the layout file you want to delete (3).
4. Click on Delete (4).
The Delete confirmation window opens (5).
5. Click on OK to delete the file (6).
Click on No, cancel this action to interrupt the deletion process.
The file will be deleted on all “write” projectors if this file exists on the “write” projector.
22 R5976790 COMMUNICATOR 09/07/2004
5. Adjustment
Image 5-6
Delete layout
5.6
Windowing
Overview
•
•
Enabling or disabling a Window
•
•
•
•
•
All window manipulations will be executed on all “write” projectors.
5.6.1
Window selection
When a certain window is not visible in the layout pane, that means that the window is disabled.
Each input corresponds with one window in the layout pane.
R5976790 COMMUNICATOR 09/07/2004 23
5. Adjustment
Using the mouse
1. Move your mouse over the window you want to select.
2. Click with the left mouse button on that window.
The border color changes to yellow. (image 5-7)
Image 5-7
Select a window
Using the menu bar
1. Click View to pull down the selection menu. (image 5-8)
The input selection menu opens.
2. Select the window (input) your want to activate.
The border color of the selected window in the layout pane changes to yellow.
24
Image 5-8
Window selection via menu bar
R5976790 COMMUNICATOR 09/07/2004
5.6.2
Enabling or disabling a Window
How to disable a window
1. Select the window. (image 5-9)
The border colors will change to yellow
2. Remove the checked symbol next to enable by clicking on it.
The window representation will be removed from the layout pane.
5. Adjustment
Image 5-9
Disabling a window
How to enable a window
1. Select the window you want to enable via the menu bar or the function keys. (image 5-10)
The window indication changes to that corresponding window and the enable box in not checked.
2. Check the enable box.
The window representation appears in the layout pane.
Image 5-10
Enabling a window
R5976790 COMMUNICATOR 09/07/2004 25
5. Adjustment
5.6.3
Moving Windows
Moving via drag and drop
1. Click on the window you want to move. (image 5-11)
The border changes to yellow and the cursor changes to a four arrow cursor.
2. Hold down the mouse button to grab the selected window.
3. Move the window to the required position. The coordinates in the right pane will change accordingly.
Image 5-11
Moving windows
Moving via the coordinates
1. Select the window you want to move.
2. Change the X and Y value indicating the actual start position of the window by clicking on the + or -
Or, by entering a new value with the keyboard.
Image 5-12
Move window via coordinates
26 R5976790 COMMUNICATOR 09/07/2004
5. Adjustment
5.6.4
Scaling Windows
Scaling via drag and drop
1. Click on the window you want to scale. (image 5-13)
The border changes to yellow and the cursor changes to a four arrow cursor.
2. Move your cursor to corner.
The cursor changes in a two arrow cursor.
3. Hold down your mouse button and drag the corner to the desired position to down-scale or upscale the selected window. The coordinates of the selected window will be automatically adjusted in the right pane.
Image 5-13
Scaling windows via drag and drop
Scaling via the height and width
1. Select first the window you want to scale. (image 5-14)
2. Change the width and height value by pushing the + or - button
Or, by entering the new values with the keyboard.
Note: The upper left corner is fixed during the scaling.
Image 5-14
Scaling via Width of Height
5.6.5
Z-order
Z-order
The layer sequence in which windows will be displayed in relation to one another.
R5976790 COMMUNICATOR 09/07/2004 27
5. Adjustment
How to order
1. Select the window you change the order.
The border changes to yellow and the cursor changes to a four arrow cursor.
2. Change the Z-value in the right pane by clicking on the + or - button (image 5-15)
Or, by entering the desired value with the keyboard.
Image 5-15
Z-order
The higher the value, the more the window is in front.
5.6.6
Full size
How to reset to full size
1. Select the window you want to size to full size. (image 5-16)
The border changes to yellow and the cursor changes to a four arrow cursor.
2. Click on the full size button. (image 5-17)
The selected window will be reset to the full size of the DMD.
28
Image 5-16
Select a window to scale
R5976790 COMMUNICATOR 09/07/2004
5. Adjustment
Image 5-17
Reset to full size
5.6.7
Aspect Ratio
Aspect ratio horizontal & vertical dimension in which the window will be displayed, e.g. 4 by 3 or 16 by 9.
How to change
1. Select the window of which you want to change the aspect ratio.
The border changes to yellow and the cursor changes to a four arrow cursor.
2. Right click on the selected window and select the desired aspect ratio. (image 5-18)
Or,
click on the aspect ratio icon and select the desired aspect ratio. (image 5-19)
Possible aspect ratios
- 3/2
- 4/3
- 14/9
- 16/9
- 21/9
- 1.85 flat
- 2.35 scope
- snap to current : fix the current aspect ratio what ever it is.
- none : no fixed aspect ratio
R5976790 COMMUNICATOR 09/07/2004 29
5. Adjustment
Image 5-19
Aspect ratio via button
Image 5-18
Aspect ratio via right click
Image 5-20
Fixed aspect ratio selected
5.7
Settings
Input File manipulations are not automatically executed on all “write” projectors.
Overview
•
•
•
•
•
•
•
•
•
•
Apply settings to all projectors
5.7.1
Introduction
Overview
With each input source corresponds a source file which contains the settings for this typical source. If there is not yet a source file available, the system can search for the most fitting file or you can associate a file yourself. This file can then be edited and saved under a new name.
Types of source files
When opening the list of source files, you will recognize 2 types of source files :
• system source files
• custom source files
The custom source files which have the same name of the system source files are indicated with a index number between brackets.
30 R5976790 COMMUNICATOR 09/07/2004
5. Adjustment
5.7.2
Load a file
How to load a file
1. Select a window. (image 5-21)
The input number and the associated file name will be indicated in the settings pain.
The Open an input file window opens (2).
When the following is selected :
Load file [All] All available files will be displayed in the Open an input file window.
Load file [Fit] Only the best fitting files will be displayed in the Open an input file window.
Or, push CTRL + L for Load file [Fit] or push CTRL + S for Load file [All].
3. Select the desired file (3) and click on Open (4).
When a system file is selected, the software will ask to create a custom file with the same name, followed with a next possible index. When OK is selected the settings of the system file will be copied into this
The settings of the selected file will be loaded.
Image 5-21
File association
R5976790 COMMUNICATOR 09/07/2004 31
5. Adjustment
Image 5-22
Load file [All]
Image 5-23
Load file [fit]
32
Image 5-24
Load file message
R5976790 COMMUNICATOR 09/07/2004
5.7.3
Save a file
How to save
1. Click on Input File on the menu bar and select Save. (image 5-25)
The settings of the actual input will be saved.
5. Adjustment
Image 5-25
Save actual settings
5.7.4
Save all file
How to save all files
1. Click on Input File on the menu bar and select Save all. (image 5-26)
The settings of the 4 active input files which are associated with the 4 inputs will be saved.
Image 5-26
Save all files
5.7.5
Rename a file
How to rename
1. Click on Input File on the menu bar and select Rename (1). (image 5-27)
The Select Input File to rename window opens (2).
2. Select a file (3) and click on Rename (4).
The rename window opens (5).
3. Click in the input field (6) and enter the new file name.
4. Click on OK (7).
R5976790 COMMUNICATOR 09/07/2004 33
5. Adjustment
Image 5-27
Rename input file
5.7.6
Delete a file
How to delete
1. Click on Input File on the menu bar and select Delete (1). (image 5-28)
The Select Input File to delete window opens (2).
2. Select an input file (3) and click on Delete (4).
The delete input file confirmation window opens (5).
3. Click Yes to delete.
34
Image 5-28
Delete input file name
R5976790 COMMUNICATOR 09/07/2004
5. Adjustment
5.7.7
Auto Load Enabled
What can be done ?
When this function is enabled, the ACSAR 2 will create by itself a new custom file when it detects a relevant input signal.
How to enable ?
1. Click on Input File on the menu bar and check Auto Load Enabled (1).
A check mark will appear in the box just before the Auto Load Enabled item.
5.7.8
Image Settings
Overview
The following image settings can be adjusted depending on the source type :
• Contrast
• Brightness
• Phase
• Sharpness
• Saturation
When a setting is not adjustable, this setting will be grayed out.
Adjusting via dragging
1. Click on the slider bar of the specific adjustment. (image 5-29)
The complete slider bar will be selected within a rectangle.
2. Move the slider up or down until the desired value for that specific adjustment is reached.
The value below the adjustment will change accordingly.
Image 5-29
Adjusting via dragging
Adjusting via the up and down keys
1. Click on the up or down arrow keys until the desired value is reached.
The value next to the arrow keys will change accordingly.
Adjusting via the input box
1. Click inside the value input box.
2. Select the actual value and enter a new value with your keyboard.
R5976790 COMMUNICATOR 09/07/2004 35
5. Adjustment
5.7.9
Input Settings
How to change
1. Click on the Input settings tab.
The input settings values will be displayed
2. Click in the input field of a setting and change the value with the keyboard.
Or, click on the up or down arrow key to change the value.
3. When the source is Interlaced, check the check box in front of Interlaced.
4. Select Single or dual path.
How to find the correct values for the item in the Input File?
Hor. line
Frame
Active pixels
Hor. start pixel
Hor. Total pixels
36
Active lines
Vert. Start Line
Vert. Total lines
Image 5-30
Input file items
Horizontal Total
Pixels
Active Pixels
Horizontal Start
Pixel
If the value for "Horizontal Total Pixels" is wrong, sampling mistakes (small vertical bars in the projected image) will be seen in the image.
Select "Total" and adjust the pixel quantity. Adjust for zero bars.
hint: if the number of bars increase, adjust in the other direction.
The "Active Pixels" : determine the width of the window on the screen. This value is normally given in the source specifications. If not, adjust until full image is displayed (no missing pixels).
number of pixels between the start of the sync signal and the start of the video information.
R5976790 COMMUNICATOR 09/07/2004
5. Adjustment
Vertical Total
Lines already filled when an active file is selected to be edited
Vertical Active
Lines number of horizontal lines determining the height of the projected image. This value is normally given in the specification of the source. If not, adjust until full image height is displayed (no missing lines)
Vertical Start Line number of lines between the start of the sync signal and the start of the video information.
Interlaced this selection is automatically filled out when file has loaded. If the image is wrong due to mismeasurement, check or leave the check box blank before interlace.
(for interlaced images, 1 frame contains 2 fields).
Horizontal Period already filled in with the correct value when active file.
Horizontal period = Horizontal Total pixels / clock frequency
5.7.10 Apply settings to all projectors
Summary
The displayed image settings and input settings of the read-write projector can be applied to all projectors when the other projectors have the same input configuration.
If you want to apply to all projectors, check the checkbox in front of To all projectors.
Image 5-31
To all projectors
A message will be displayed to warn that all projectors must have the same configuration.
Image 5-32
“To all projectors” message
C
AUTION
:
All projectors must have the same input modules, in the same input slots !
R5976790 COMMUNICATOR 09/07/2004 37
5. Adjustment
5.8
Input slot configuration
What can be done ?
Each of the input slots can be configured with the correct setting.
How to configure ?
1. Click on Installation and select Input slots. (image 5-33)
The Input slots configuration menu appears. (image 5-34)
2. Click on the drop down box next to the slot which must be configured.
3. Select the desired configuration.
When all configuration are finished, click on OK.
Image 5-33
Input slots selection
Image 5-34
Input slots configuration
38 R5976790 COMMUNICATOR 09/07/2004
6. Projector Configuration
6. PROJECTOR CONFIGURATION
Overview
•
Set up of the Serial Bus Address
•
Set up of the Network Properties
6.1
Set up of the Serial Bus Address
Do not change the serial bus address when connected over a serial loop.
How to set up
1. Click on the + or – button next to the address indication. (image 6-1)
2. Click on Apply now.
The serial bus address will be set, the Apply now button will gray out.
Image 6-1
Serial Bus Address Setting
6.2
Set up of the Network Properties
Overview
•
•
Assign an Ethernet address via DHCP
•
Manually assign an Ethernet address
6.2.1
Ethernet Connection
IP
Internet Protocol. The network layer of TCP/IP. Required for communication with the internet.
Subnet mask
A number that is used to identify a subnetwork so that IP addresses can be shared on a local area network.
R5976790 COMMUNICATOR 09/07/2004 39
6. Projector Configuration
Default Gateway
A router that serves as an entry point into and exit point out of a network. For example, a local network (LAN) may need a gateway to connect it to a wide area network (WAN) or to the
Internet.
DHCP
Dynamic host configuration protocol. DHCP is a communications protocol that lets network administrators manage centrally and automate the assignment of IP addresses in an organization’s network. Using the Internet Protocol, each machine that can connect to the Internet needs a unique IP address. When an organization sets up its computer users with a connection to the Internet, an IP address must be assigned to each machine. Without DHCP, the IP address must be entered manually at each computer and, if computers move to another location in another part of the network, a new IP address must be entered. DHCP lets a network administrator supervise and distribute IP addresses from a central point and automatically sends a new IP address when a computer is plugged into a different place in the network.
What should be set up for the Ethernet address
2 ways can be used to assign an address:
• use the DHCP setting so that a automatic address will be assigned.
• Assign manually an IP address, Subnet-mask, default gateway address.
- Set the IP-Address field to the desired value. This must NOT be 0.0.0.0 for static IP-Address assignment. The IP address identifies a projector’s location on the network in the same way a street address identifies a house on a city block. Just as a street address must identify a unique residence, an IP address must be globally unique and have a uniform format.
- Set the Subnet-Mask as appropriate for the local subnet.
- Set the Default-Gateway to the IP-Address of the local router (MUST be on the local subnet!) on the same network as this projector that is used to forward traffic to destinations beyond the local network. This must not be 0.0.0.0. If there is no router on the projector’s local subnet then just set this field to any IP-Address on the subnet.
6.2.2
Assign an Ethernet address via DHCP
How to set up
1. Click on the BARCO button. (image 6-2)
The Network settings window will open. (image 6-3)
2. Check the check box next to Obtain an IP address automatically (DHCP).
This selection will become active. Other selections are grayed out.
3. Click on OK to activate.
40
Image 6-2
Network properties
R5976790 COMMUNICATOR 09/07/2004
6. Projector Configuration
Image 6-3
Network settings window, Barco controller
6.2.3
Manually assign an Ethernet address
How to set up
1. Click on the BARCO button.
The Network settings window will open. (image 6-4)
2. Check the check box next to Use the following IP address
3. Click in the input field of the IP address and fill out the 4 fields.
Note: An address contains 4 octets with a maximum value of 255.
This must NOT be 0.0.0.0 for static IP-Address assignment
4. Click in the Subnet mask input fields and fill out the 4 fields as appropriate for the local subnet.
5. Click in the Default Gateway input fields and fill out the 4 fields. Set the Default-Gateway to the IP-Address of the router (MUST be on the local subnet!).
Note: This must NOT be 0.0.0.0.
If there is no router on the projector’s local subnet then just set this field to any IP-Address on the subnet.
6. Click OK to activate.
R5976790 COMMUNICATOR 09/07/2004 41
6. Projector Configuration
42
Image 6-4
Network settings, Barco controller
If no router is present, then the PC’s IP Address MUST be within the same subnet as the projector’s IP Address in order for communication to be possible. This requires checking the PC’s and projector’s Subnet-Mask settings.
IP address examples
First example
• PC IP Address : 192.168.100.5
• PC Subnet Mask : 255.255.255.0
• Projector IP Address : 192.168.100.3
• Projector Subnet Mask: 255.255.255.0
Result : Communication possible. PC address is in the subnet range of the projector’s IP address.
Second example
• PC IP Address : 10.16.236.100
• PC Subnet Mask : 255.255.255.0
• Projector IP Address : 192.168.100.3
• Projector Subnet Mask: 255.255.255.0
Result : No communication possible. PC address is not in the subnet range of the projector’s IP address.
Third example
• PC IP Address : 192.168.200.1
• PC Subnet Mask : 255.255.255.0
• Projector IP Address : 192.168.100.3
• Projector Subnet Mask: 255.255.255.0
Result : No communication possible. PC address is not in the subnet range of the projector’s IP address.
The third group in the PC IP address and Projector IP address must be the same.
Fourth example
• PC IP Address : 192.168.200.1
• PC Subnet Mask : 255.255.0.0
• Projector IP Address : 192.168.100.3
• Projector Subnet Mask: 255.255.0.0
R5976790 COMMUNICATOR 09/07/2004
6. Projector Configuration
Remark : Communication possible. PC address is in the subnet range of the projector’s IP address. The third group in the IP¨ addresses can be any value as the third group in the subnet mask is 0.
R5976790 COMMUNICATOR 09/07/2004 43
6. Projector Configuration
44 R5976790 COMMUNICATOR 09/07/2004
7. PROJECTOR STATUS
7.1
General overview
Summary
This interface gives feedback on any item that can be red out in the XLM projector.
7. Projector Status
Image 7-1
Overview status
If the Status indication is NOK, follow the description in the error message window and check the read outs to find out what is wrong with your projector.
7.2
General projector properties
Overview
Image 7-2
Projector properties
R5976790 COMMUNICATOR 09/07/2004 45
7. Projector Status
• Lamp run time : expressed in hours. Time lamp is running since first start up of this lamp.
• Lamp strikes : number of strikes since first start up of the lamp.
• Active cooling Red (active - not active) : when active, Peltier cooling is activated for Red DMD.
• Active cooling Green (active - not active) : when active, Peltier cooling is activated for Green DMD.
• Active cooling Blue (active - not active) : when active, Peltier cooling is activated for Blue DMD.
• Waterflow : checks if waterflow is possible. See also location waterflow switch.
Image 7-3
Waterflow switch location
7.3
Status overviews
Overview
•
•
•
7.3.1
Voltage statuses
Status overview
When one of the voltages are out of specification, the voltage indication will be red.
46 R5976790 COMMUNICATOR 09/07/2004
7. Projector Status
Image 7-4
Status overview voltages
7.3.2
Temperature statuses
Status overview
When one of the temperatures are out of specification, the indication will be red.
R5976790 COMMUNICATOR 09/07/2004 47
7. Projector Status
Image 7-5
Status overview temperatures
W
ARNING
:
Servicing only allowed by a Barco authorized service technician.
Sensor locations
48
Image 7-6
Ambient temperature sensor
Image 7-7
Sensors on modules
A Sensor on PFC
B Sensor on heatsink SMPS
R5976790 COMMUNICATOR 09/07/2004
Image 7-8
Lamp house sensor
7.3.3
Fan statuses
Status overview
If one of the fans fail, the corresponding indication will be displayed in red.
7. Projector Status
Image 7-9
Status overview fans
W
ARNING
:
Servicing only allowed by a Barco authorized service technician.
R5976790 COMMUNICATOR 09/07/2004 49
7. Projector Status
Fan locations
Image 7-10
Cold mirror bottom fan
Image 7-11
Cold mirror top fan
Image 7-12
Fan 1 – 4 elcabox
Image 7-13
Lamp fan cathode
Image 7-14
Lamp fan anode
Image 7-15
Start pulse generator fan
7.4
Projector log information
Overview
When clicking on the Log button in the tab bar, a log overview window will be displayed.
50 R5976790 COMMUNICATOR 09/07/2004
Image 7-16
Log information
7. Projector Status
R5976790 COMMUNICATOR 09/07/2004 51
7. Projector Status
52 R5976790 COMMUNICATOR 09/07/2004
8. Version Info
8. VERSION INFO
Overview
•
8.1
Version Information
Overview
The version information pane gives an overview of the firmware versions used in the boards.
The following boards are listed:
• Formatter Board
• Modules/Devices
• Settings
Image 8-1
Version information
R5976790 COMMUNICATOR 09/07/2004 53
8. Version Info
54 R5976790 COMMUNICATOR 09/07/2004
Glossary
GLOSSARY
(LAN) may need a gateway to connect it to a wide area network (WAN) or to the Internet.
manage centrally and automate the assignment of IP addresses in an organization’s network. Using the
Internet Protocol, each machine that can connect to the Internet needs a unique IP address. When an organization sets up its computer users with a connection to the Internet, an IP address must be assigned to each machine. Without DHCP, the IP address must be entered manually at each computer and, if computers move to another location in another part of the network, a new IP address must be entered. DHCP lets a network administrator supervise and distribute IP addresses from a central point and automatically sends a new IP address when a computer is plugged into a different place in the network.
Internet Protocol. The network layer of TCP/IP. Required for communication with the internet.
A window represents the active area of an input source.
The layer sequence in which windows will be displayed in relation to one another.
R5976790 COMMUNICATOR 09/07/2004 55
Glossary
56 R5976790 COMMUNICATOR 09/07/2004
Index
INDEX
A
C
D
I
L
R5976790 COMMUNICATOR 09/07/2004
N
P
General projector properties 45
57
Index
R
S
U
V
58 R5976790 COMMUNICATOR 09/07/2004
Revision Sheet
To:
Barco nv Events/Documentation
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.89.70, Fax: +32 56.36.88.24
E-mail: [email protected], Web: www.barco.com
From:
Date:
Please correct the following points in this documentation (R5976790/00): page wrong correct
R5976790 C OMMUNICATOR 09/07/2004
advertisement