InFocus IN310 2, 4, 6, 8, W32 20, W32 40, W32 60 projector User manual

SALE on Projector Bulbs at www.BulbAmerica.com

take additional 5% Off with coupon code 5PDF

IN3102 IN3104 IN3106 IN3108

Regulatory models W3220, W3240 and W3260

010-0710-02

Declaration of Conformity

Oregon 97070 USA

European Office: Louis Armstrongweg 110, 1311 RL Almere, The

Netherlands

We declare under our sole responsibility that this projector conform to the following directives and norms:

EMC Directive 2004/108/EC

EMC: EN 55022

EN 55024

EN 61000-3-2

EN 61000-3-3

Low Voltage Directive 2006/95/EC

Safety: IEC 60950-1: 1

Trademarks

st

Edition



DisplayLink is a trademark of DisplayLink Corporation.

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark of

International Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems

Incorporated. DLP® and the DLP logo are registered trademarks of Texas

Instruments and BrilliantColor™ is a trademark of Texas Instruments.

InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks or trademarks of InFocus Corporation in the United States and other countries.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by InFocus Corporation may void authority to operate the equipment.

Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

Agency Approvals

UL, cUL

Other specific Country Approvals may apply. Please see product certification label.

This document applies to regulatory models W3220, W3240, and W3260.

Input ratings: 100-240Vac, 3.3 - 1.2A (W3220, W3260), 3.9 - 1.4A (W3240),

50-60Hz

InFocus reserves the right to alter product offerings and specifications at any time without notice.

1

Table of Contents

Introduction 3

Positioning the projector

Projector and device connector guide

Connecting a computer source

Required computer connections

(DisplayLink or VESA)

5

6

9

Optional computer connections

Displaying an image

Adjusting the image

Connecting a video device

Video device connections

Composite video connection

HDMI 1.3 connection

S-video connection

VESA connection

Component video connection

Shutting down the projector

Troubleshooting your setup

Using the remote control

Using the audio

Using the keypad buttons

Optimizing computer images

Presentation features

Optimizing video images

Customizing the projector

Using the menus

Basic Picture menu

Advanced Picture menu

Setup menu

Status and Service menu 32

Maintenance 33

Cleaning the lens

Using the security lock

Replacing the projection lamp

33

33

34

12

13

13

13

9

9

10

11

27

28

29

30

25

25

26

26

14

22

23

24

13

13

13

14

Important Operating Considerations for Safety

• Place the projector in a horizontal position no greater than 15 degrees off axis.

• Locate the projector in a well-ventilated area without any obstructions to intake or exhaust vents. Do not place the projector on a tablecloth or other soft covering that may block the vents.

• Locate the projector at least 4' (1.2 m) away from any heating or cooling vents.

• Use only InFocus-approved ceiling mounts.

Warning:

To prevent eye injury if the projector is ceiling mounted, wear protective eyewear before opening lamp door. A warning sticker is included with the user documentation. Place this sticker on the lamp door if the projector is mounted on the ceiling.

• Only genuine InFocus lamps are tested for use in this projector.

InFocus is not liable for the performance, safety or certification of any other lamps. The use of other lamps violates the projector warranty and voids all certification marks on this projector.

• Use only the power cord provided. A surge-protected power strip is recommended.

• Refer to this guide for proper startup and shutdown procedures.

• Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org.

• In the unlikely event of a lamp rupture, particles may exit through the projector side vents. When the projector is turned on, keep people, food, and drinks out of the "keep out" area under and around the projector, as indicated by the "X" areas below.

2’ / 0.6 m m

3’

/ 1

8’ / 2.4 m

5’

/ 1

.5 m

Follow these instructions to help ensure image quality and lamp life over the life of the projector. Failure to follow these instructions may affect the warranty. For complete details of the warranty, see the Warranty Booklet.

2

Introduction



Your new digital projector is simple to connect, easy to use, and straightforward to maintain. It is a versatile projector that is flexible enough for business presentations and home video viewing too. The IN3102/

IN3104 has native XGA 1024x768 resolution, and the IN3106/IN3108 has

WXGA 1280x800 resolution. This guide applies to all products. They are compatible with a wide variety of computers and video devices.

focus (front ring) zoom (rear ring)

Product specifications

To read the latest specifications on your multimedia projector, be sure to visit our website at www.infocus.com, as specifications are subject to change.

remote control receiver (IR)

Accessories

The standard accessories that came with your projector are listed in the included Quick Start Poster/Booklet. Optional accessories can be found on our website at www.infocus.com or at your retailer or dealer.

Online registration

Register your projector on our website at www.infocus.com/register to activate your warranty and receive product updates, announcements, and registration incentives.

lens elevator foot touch keypad elevator foot connector panel remote control receiver (IR) power cord connector

3

Connector panel

The projector provides both computer and video connection options, including:



• VESA computer (2)

• HDMI, for computer (1) and for video (1)

• S-video

• Composite video

• Separate audio inputs for video and computer

• USB DisplayLink connector, for computer audio/video input. This

USB connection also provides slide advance (and mouse control when used with an optional remote control only)

The projector also provides the following connectors:

• Monitor out, to provide an image on your desktop computer as well as on the projection screen

• Audio out, to provide sound for external speakers

• A 5 volt DC output (see below)

It also has an RS-232 connector for serial control. The Command Line

Interface (CLI) specifications and commands are on our website.

NOTE: DisplayLink video and audio is not sent to monitor out and audio out.

5 volt DC output

The 3.5mm mini-jack triggers provide a 5 volt, 2 amp DC output. It provides a constant output while the projector is on. It is designed to provide power for an InFocus LiteShow II wireless device, which allows wireless projection. More information can be found on our website at www.infocus.com

or at your retailer or dealer.

audio in composite video

S-video monitor out

HDMI for video computer audio out

5 volt output security lock RS-232 DisplayLink connector

4

Positioning the projector



To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Here are some general guidelines:

Table 1: (IN3102 & IN3104)

Range of distance to the screen for a given screen size

Distance to screen

• Position the projector on a flat surface at a right angle to the screen. The projector must be at least 4.9 feet (1.5m) from the projection screen.

• Position the projector within 10 feet (3m) of your power source and within 6 feet (1.8m) of your video device (unless you purchase extension cables). To ensure adequate cable access, do not place the projector within 6 inches (.15m) of a wall or other object.

• If you are installing the projector on the ceiling, refer to the installation guide that comes with the Ceiling Mount Kit for more information. To turn the image upside down, see “Ceiling mount” on page 31. We recommend using an InFocus authorized ceiling mount.

• Position the projector the desired distance from the screen. The distance from the lens of the projector to the screen, the zoom setting, and the video format determine the size of the projected image.

• The image exits the projector at a given angle. IN3102/IN3104 image offset is 115% ; IN3106/IN3108 image offset is 112.4%. This means that if you have an image 10’ high, the bottom of the image will be 1.5'

(IN3102/IN3104) and 1.24' (IN3106/IN3108) above the center of the lens.

10 ft high image

(IN3106/IN3108)

10 ft high image

(IN3102 & IN3104)

Diagonal Screen

Size (inches/m)

60/1.5

80/2.0

90/2.3

150/3.8

Maximum distance (feet/m)

8.6/2.6

11.5/3.5

12.9/3.9

21.5/6.6

Minimum

Distance (feet/ m)

7.8/2.4

10.4/3.2

11.7/3.6

19.5/5.9

Table 2: (IN3106/IN3108)

Range of distance to the screen for a given screen size

Diagonal Screen

Size (inches/m)

60/1.5

80/2.0

90/2.3

150/3.8

Distance to screen

Maximum distance (feet/m)

7.3/2.2

9.7/2.9

10.9/3.3

18.1/5.5

Minimum

Distance (feet/ m)

6.5/2.0

8.7/2.7

9.8/3.0

16.3/5.0

bottom of image

1.24 ft above center of lens lens center

Projection angle bottom of image

1.5 ft above center of lens lens center

Projection angle

5

Projector and device connector guide



The following illustration and table should help you find the connectors to use and obtain the best resolution possible from your input devices, such as computers, standard VCRs, DVD players (progressive and interlaced),

HDTV sources (1080i, 1080p and 720p HDTV formats), TV and satellite tuners, camcorders, video games (progressive and interlaced), and laser disc players.

audio in composite video monitor out

HDMI for video computer

S-video audio out

5 volt output security lock RS-232

DisplayLink connector

6

Video Device

Standard Broadcast TV (not

HDTV) via: cable, digital cable, satellite TV, DVD, or VCR

Video Compatibility



If Your Device

Connector Is

Attach to Adapter or

Labeled Connector on Projector

For Setup Instructions, see

NTSC, PAL, and

SECAM formats

Composite video or S-video

Video 3 or Video 2

Comments

Composite video connection on page 13.

S-video connection on page 13

Not for progressive

(i.e. HDTV) sources.

See page 8.

Standard Video Camera

NTSC, PAL, and

SECAM formats


Video 3 or Video 2

Standard Video Game

NTSC, PAL, and

SECAM formats


Video 3 or Video 2



Not for progressive


See page 8.



Not for progressive


See page 8.

7

Video Device

HDTV

(High Definition TV)

Progressive DVD

Progressive Video Game

Video Compatibility



If Your Device

Connector Is

Attach to Adapter or

Labeled Connector on Projector

For Setup Instructions, see

1080i, 1080p, 720p VGA Computer 3 or

Computer 2

VESA connection on page 13

Component 480i Component video Computer 3 or

Computer 2 via optional VESA to

Component adapter

HDMI

Component video connection on page 13

HDMI connection on page 13

Comments


1080i, 1080p, 720p

Component 480p and 480i

1080i, 1080p, 720p

Component 480p and 480i

VGA

Component video

VGA

Component video

Computer 3 or

Computer 2

Computer 3 or


Component adapter

HDMI

Computer 3 or

Computer 2

Computer 3 or


Component adapter

HDMI






8

Connecting a computer source



Required computer connections (DisplayLink or VESA)

connect USB cable

If your computer has Windows XP SP2 or newer*, connect the USB cable between your computer's USB port and the projector's DisplayLink connector, then follow the instructions on the screen. See the DisplayLink Manager

User's Guide for more information.

* For the latest information about support for other operating systems

(including Apple), go to www.infocus.com/support/displaylink

Or, connect one end of the provided computer cable to the Computer 2 or

Computer 3 connector on the projector and the other to the VESA connector on your computer. If you are using a desktop computer, you will need to disconnect the monitor cable from the computer’s video port first (you can connect this monitor cable to the Monitor Out connector on the projector, see below).

Connect the black power cord to the Power connector on the side of the projector and to your electrical outlet. The Power light on the Status

Indicator Panel (page 14) turns amber.

NOTE

: Always use the power cord that shipped with the projector.

connect computer cable connect power cord

Optional computer connections

To get sound from the projector, connect an audio cable (optional cable, not included) to your computer and to the Audio In Computer connector on the projector. You may also need an adapter.

If you are using a desktop computer and want to see the image on your computer screen as well as on the projection screen, connect the computer’s monitor cable to the Monitor Out connector on the projector.

NOTE

: DisplayLink video and audio is not sent to monitor out and audio out.

To advance slides in a PowerPoint presentation using the remote control, plug the USB cable into the USB mouse connector on your computer and the DisplayLink connector on the projector.

9

connect audio cable connect monitor cable

MOLEX

MOLEX

Displaying an image


take additional 5% Off with coupon code 5PDF press Power button

Touch the Power button.

The Power button blinks green and the fans start to run. When the lamp comes on, the start up screen displays and the Power button is steady green.

It can take a minute for the image to achieve full brightness.

? No start up screen?

Get help on page 15.

turn on computer or video device

Turn on your computer or video device.

The image should appear on the projection screen. If it doesn’t, press the

Source button on the projector’s keypad or remote.

If you are using a VESA cable to connect your computer to the projector (instead of DisplayLink):

If using a laptop, make sure its external video port is active.

Many laptops do not automatically turn on their external video port when a projector is connected. Usually a key combination like FN + F8 or CRT/

LCD key turns the external display on and off. Locate a function key labeled

CRT/LCD or a function key with a monitor symbol. Press FN and the labeled function key simultaneously. Refer to your laptop’s documentation to learn your laptop’s key combination

.

? No laptop image?

Try pressing the Auto Image button on the keypad.

Get help on page 15.

? Is your laptop connected to the projector's DisplayLink connector?

See the

InFocus DisplayLink Manager User's Guide for troubleshooting information.

activate laptop’s external port monitor key or

LCD/CRT key

FN key

10

Adjusting the image


take additional 5% Off with coupon code 5PDF adjust height

If necessary, adjust the height of the projector by pressing the elevator foot release button to extend the foot.

If necessary, rotate the leveling foot located at the rear of the projector.

Avoid placing your hands near the hot exhaust vent at the side of the projector.

release button elevator foot

Position the projector the desired distance from the screen at a 90 degree angle to the screen.

See page 5 for a table listing screen sizes and distances.

adjust distance

Adjust the zoom or focus.

adjust zoom or focus

If the image is not square, first make sure that the projector is perpendicular to the screen. If the image is larger or smaller on the top or bottom edge of the screen, press the top Keystone button to reduce the upper part of the image, and press the bottom Keystone button to reduce the lower part.

If the left or right side of the screen is larger or smaller the other, you can turn the projector to the left or to the right a few degrees to square the image.

Adjust the Contrast or Brightness in the Basic Picture menu. See page 28 for

help with these menu adjustments.

For Aspect Ratio, keep in mind that DVD players must be configured for

16:9 in order to view the highest quality image. For more information

regarding Aspect Ratio, see page 12.

zoom (rear ring) adjust keystone adjust Basic Picture menu

11

focus (front ring)

Connecting a video device



You can connect video devices such as VCRs, DVD players, camcorders, digital cameras, video game consoles, HDTV receivers, and TV tuners to the projector. You can connect the audio directly to the projector to get sound from the built-in speaker, or you can bypass the projector’s audio system and connect the audio directly from your source to a stereo or home theater system.

You can connect the projector to most video devices that can output video.

You cannot directly connect the coaxial cable that enters your house from a cable or satellite company, the signal must pass through a tuner first.

Examples of tuners are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes. Basically, any device that can change channels is considered a tuner.

Before connecting your projector, you should decide which aspect ratio you want to use. The projector’s Aspect Ratio setting is accessed through the

Resize button on the remote or through the projector’s Basic Picture Menu.

See page 28 for more information.

What is Aspect Ratio?

Aspect ratio is the ratio of the image width to image height. TV screens are usually 4:3. HDTV and most DVDs are 16:9. If you’re projecting onto a screen, the size/shape of the screen may determine which aspect ratio to use. If you are projecting onto a blank wall, you don’t have the screen size restriction. What you plan to project will also help you choose between 4:3 and 16:9. Most TV shows are 4:3, while most movies are 16:9.

If you have a 16:9 screen then you should select an aspect ratio of 16:9 for anamorphic movies or HDTV, and Native for 4:3 content. If you have a 4:3 screen you should still use 16:9 for anamorphic movies or HDTV, but you also have the option of using either 4:3 (to fill the screen) or Native (for direct pixel mapping) for 4:3 content. Keep in mind that anamorphic movies only appear correctly if the DVD player is set to output to a 16:9 television.

12

16:9 screen

Do Not Use

4:3 mode

16:9 mode

Native mode

(NTSC only)

Video device connections

No video cables are provided with the projector. You can order cables from

InFocus or provide your own.

Composite video connection



Plug the composite video cable’s yellow connector into the video-out connector on the video device. Plug the other yellow connector into the yellow Video 3 connector on the projector.

Plug the white connector of a Mini-plug audio Y-cable into the left audio out connector on the video device and plug the red connector into the right audio out connector on the video device. Plug the other end of the cable into the Audio In Video connector on the projector.

Keep in mind that video output from composite connections is not as high quality as S-video.

VESA connection

If your video device has a 15-pin VGA output, plug one end of the included computer cable into the VGA connector on your video source. This connector may be labeled “To Monitor” on the video source. Plug the computer cable into the Computer 3 or Computer 2 connector on the projector.

Component video connection

If your HD video device has component connectors, an optional

Component to VESA adapter can be used. Plug the component cable into the video device. Plug the other end of the component cable into the adapter and plug the adapter into the Computer 3 or Computer 2 connector.

Component offers the highest quality video output.

HDMI 1.3 connection

HDMI is a standard, uncompressed, all-digital audio/video interface.

HDMI provides an interface between sources, such as set-top boxes, DVD players, and receivers and your projector. Plug an HDMI cable into the video-out connector on the video device and into the HDMI connector on the projector.

To take advantage of HDMI 1.3 Deep Color (30 bit) you must have a 1.3compatible source.

S-video connection

If your video device uses a round, four-prong S-video connector, plug an Svideo cable into the S-video connector on your video device and into the

Video 2

connector on the projector. Use the audio cable as described above.

Keep in mind that S-video delivers higher quality video output than composite.

13

Shutting down the projector



The projector automatically displays a black screen after no active source is detected for 30 minutes. This black screen helps preserve the life of the projector. The image returns when an active source is detected or a remote or keypad button is pressed.

Screen Save Time

You can make the black screen appear after a preset number of minutes by

turning on the Screen Save Time feature in the Setup menu. See page 30.

Auto Off Time

The projector also has an Auto Off Time feature that automatically turns the projector off after no active sources are detected and no user interaction with the projector is performed for 30 minutes. By default, this feature is off.

You can change the length of time, see page 30.

The Status Indicator Panel on top of the projector indicates the state of the projector and can help you troubleshoot.

Icon

Table 3: Status indicator light behavior and meaning

Power, solid amber

Power, blinking green

Power, solid green

Meaning

The projector is plugged in.

The power button has been pressed and the software is initializing.

The projector is on and initialized.

Turning off the projector

To turn the projector off, press the Power button on the remote or keypad.

The lamp turns off and the LED blinks amber for 1 minute while the fans continue to run to cool the lamp. When the lamp has cooled, the LED lights amber and the fans stop. Unplug the power cable to completely power off the projector.

Troubleshooting your setup

If your image appears correctly on the screen, skip to the next section. If it does not, troubleshoot the setup.

Power, blinking amber

Thermometer

Lamp

The power button has been pressed to turn the projector off and the fans are running to cool the projector.

The projector is too hot. Make sure the

vents aren’t blocked (see page 20). Turn

off the projector and wait one minute, then turn the projector on again. Contact

Technical Support if the problem persists.

Visit www.infocus.com/support to contact service.

Turn off the projector and wait one minute, then turn the projector on again.

If the lamp light turns on again, replace the lamp and reset the lamp timer.

Wrench/Service Turn off the projector and wait one minute, then turn the projector on again.

If the service lamp turns on again, service is required. Visit www.infocus.com/ support to contact service.

14

Problem

No start up screen

A

Only start up screen appears

Startup

Screen

A



Solution

Plug power cord into the projector press power button

Result

Correct image

Startup

Screen

If your computer is using the projector's DisplayLink connector, see the DisplayLink User's Guide for troubleshooting information.

Press the Source button activate laptop’s external port

Computer image projected

A

A

Restart laptop

15

Prolem

No computer image, just the words “Signal out of range”

Signal out of

the range



Solution

Press the Auto Image button on keypad adjust computer refresh rate in Control Panel > Display > Settings > Advanced

> Adapter (location varies by operating system)

Result

Computer image projected

A

A

Only my laptop’s background appears, not the

Desktop icons

A

A

A

You may also need to set a different resolution on your computer, as shown in the following problem, “image fuzzy or cropped”

If your computer is using the DisplayLink connector, use

DisplayLink Manager software to change the display mode from

Extended Desktop to Duplicated Desktop. See the DisplayLink

Manager User's Guide for more information.

Disable “Extend my Windows Desktop” in Control Panel >

Display > Settings > Display 2 (location varies by operating system)

Background and Desktop projected

A

A

Uncheck this option, then click Apply

16

Prolem

Image fuzzy or cropped

A

A

Image not centered on screen

Solution



Set your computer’s display resolution to the native resolution of the projector (Start > Settings > Control

Panel > Display > Settings tab)

Result

Image clear and not cropped

A

For a laptop, disable laptop monitor or turnon dual-display mode

Move projector, adjust zoom, adjust height

A

Correct image

Adjust horizontal or vertical position in


17

Prolem

Image not square

Image not sharp

Solution



Adjust Keystone on keypad

Adjust Sharpness in the Basic Picture menu

Result

Square image

Correct image

Image does not fit 4:3 or 16:9 screen Change aspect ratio to 4:3 or 16:9 in Basic

Picture>Aspect ratio menu

Correct image

18

Prolem

Image upside down

A

Image reversed left to right

A

Projected colors don’t match source

Solution



Turn off Ceiling Mount in Setup menu

Result

Correct image

Turn off Rear Project in Setup menu Correct image

COLOR

Adjust color, tint, brightness, contrast in the Basic

Picture menu

Correct image

COLOR

19

Prolem

The video embedded in my PowerPoint presentation does not play on the screen

Solution



If your computer is using the projector's DisplayLink connector, see the DisplayLink User's Guide for video troubleshooting information.

Turn off the internal LCD display on your laptop

A

Result

Embedded video plays correctly

A

B

A

B

A

B

Lamp won’t turn on, Temperature light is on

A

Temperature light

Make sure vents aren’t blocked, turn off the projector and allow it to cool for one minute

Lamp turns on

Startup

Screen

20

Prolem

“Replace lamp” message appears at startup, lamp won’t turn on, Lamp light is turned on

A

Lamp light

Solution



Lamp must be replaced (see page 34)

lamp door

Result

Lamp turns on

Startup

Screen replace lamp

Still need assistance?

If you need assistance, visit our website at www.infocus.com/service or call us.

Check out our HOW TO section there for additional information on using this projector for home theater or gaming applications. See the Quick Start

Poster/Booklet for support contact information.

This product is backed by a limited warranty. An extended warranty plan may be purchased from your dealer. When sending the projector in for repair, we recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit. Please insure your shipment for its full value.

21

Using the remote control



The remote uses two (2) provided AA batteries. They are easily installed by removing the cover from the remote’s back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover.

Caution

: When replacing the batteries, be aware that using batteries other than the type provided with the projector may risk severe damage to the remote. When disposing of the batteries, be sure to do so in an environmentally proper manner.

navigation buttons

To operate, point the remote at the front of the projector (not at the computer). The range of optimum operation is about 15 feet (4.5m).

Press the remote’s Power button to turn the projector on and off (see page 14

for shutdown info).

Press the remote’s Menu button to open the projector’s menu system. Use the arrow buttons to navigate, and the Select button to select features and

adjust values in the menus. See page 27 for more info on the menus.

The remote also has a Source button to switch between sources.

The remote also has:

• Volume buttons to adjust the sound.

• Custom button that can be assigned to a special function, like Blank

Screen or Freeze (see page 30).

• Source button to switch between sources.

• Blank button to blank the screen.

• Presets

button to select stored settings (see page 28).

• Mute button to silence the audio.

• Auto Image button to resynch the projector to the source

• Resize

button to switch among aspect ratios (see page 28).

Troubleshooting the remote

• Make sure the batteries are installed in the proper orientation and are not dead.

• Make sure you’re pointing the remote at the projector or the screen, not the computer, and are within the remote range of 15 feet (4.5m). For best results, point the remote at the projector.

22

Using the audio


take additional 5% Off with coupon code 5PDF connect audio cable

Using the projector’s speakers

When the computer is using the DisplayLink connector, both audio and video are sent over the USB cable to the projector and audio will play from the projector's speakers.

For inputs other than DisplayLink, to use the projector's speakers, connect the audio source to the Audio In Computer or Video connectors.

To adjust the volume, press the Volume buttons on the keypad or remote.

adjust volume

Troubleshooting Audio

If you aren’t hearing the audio, check the following:

• If your computer is using the projector's DisplayLink connector, see the

InFocus DisplayLink Manager User's Guide for audio troubleshooting information

• Make sure the audio cable is connected to the correct Audio In connector, Computer or Video.

• Make sure the volume is turned up enough. Press the Volume button on the keypad or remote.

• Make sure the correct source is active.

• Make sure that you are connected to an “audio out” connector on the source as opposed to a “line-in” or “microphone” connector.

• Adjust the audio source.

• If playing a video, make sure the playback has not been paused.

Connecting external speakers

The projector can be attached to external amplified speakers by connecting a 3.5mm stereo audio cable from the Audio Out connector on the projector to the amplified speakers. Alternatively, you can bypass the projector’s audio system and connect the audio directly from your source to a stereo or home theater system.

external speakers with own power source

23

speaker cable audio out

Using the keypad buttons



Most buttons are described in detail in other sections, but here is an overview of their functions:

Power

–turns the projector on and off (page 10).

Auto Image –resets the projector to the source.

Presets

–cycles through the available preset settings (page 28).

Keystone

–adjusts squareness of the image (page 11).

Menu

–opens the on-screen menus (page 27).

Select

–confirms choices made in the menus (page 27).

Up/Down arrows

–navigates to and adjusts settings in the menus (page 27).

Volume

–adjusts sound (page 23).

Source

–changes the active source (page 10).

menu navigation buttons

24

Optimizing computer images

using the menus, see page 27.

•

•

•

•

(page 28).

source (page 28).

(page 28).

Advanced Picture menu (page 29).



After the projector is running and the image is on the screen, you can optimize the image using the onscreen menus. For general information on

Adjust the Keystone, Contrast, or Brightness in the Basic Picture menu

Change the Aspect Ratio. Choose the option that best fits your input

Adjust the Color Temperature in the Advanced Picture menu

Adjust the Phase, Tracking, or Horizontal or Vertical position in the

Presentation features

Several features are provided to make giving presentations easier. Here is an overview, details are found in the menu section.

• The Custom key allows you to assign various features to the button.

The default effect is Source Info, which displays information about the

projector and current source. See page 30 for details.

• The Search Screen option lets you change the appearance of the blank

screen and start up screen (page 31).

• Two options, Auto Off and Screen Save Time, are provided to automatically shut down the projector after several minutes of inactivity or display a black screen. This helps preserve lamp life

(page 30).

• Once you have optimized the image for a particular source, you can save the settings using Presets. This allows you to quickly recall these

settings later (page 28).

• If your computer is using the projector's DisplayLink connector, see the

InFocus DisplayLink Manager User's Guide for information about optimizing images.

25

Optimizing video images

•

Select a Sharpness setting (page 28).



After your video device is connected properly and the image is on the screen, you can optimize the image using the onscreen menus. For general

information on using the menus, see page 27.

• Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Basic

Picture menu (page 28).

• Change the Aspect Ratio. Choose the option that best fits your input

source (page 28).

•

Adjust the Color Temperature. Select a listed warmth value (page 29).

•

Turn on Overscan to remove noise on the edges of the image (page 29).

Customizing the projector

You can customize the projector for your specific setup and needs. See

page 30 to page 31 for details on these features.

•

•

•

•

•

•

For rear projection, turn Rear Project on in the Setup menu.

For ceiling mounted projection, turn Ceiling Mount on in the Setup menu.

Specify which source the projector checks first for active video during power-up.

Specify the function of the Custom key on the remote.

Turn the projector’s display messages on and off.

Turn on power saving features.

• Specify appearance of blank screen and startup screen.

• Specify the language viewed on the menus.

• Save settings for the active source as a preset.

Dynamic Messaging

You can use Command Line Interface (CLI) commands to display text messages on the projector (for example, to display urgent alert messages to employees). This requires a connection to the projector’s RS-232 serial control connector. Go to our support website to download the RS-232 command reference for your projector.

26

Using the menus



To open the menus, press the Menu button on the keypad or remote. (The menus automatically close after 60 seconds if no buttons are pressed.) Use the arrow buttons to move up and down to highlight the desired menu, then press the Select button.

To change a menu setting, highlight it, press Select, then use the up and down arrow buttons to adjust the value or select an option or turn the feature on or off. Press Select to confirm your changes. Use the arrows to navigate to another setting. When your adjustments are complete, press

Menu to access a different menu; press the Menu button at any time to navigate to the higher-level menu and ultimately close the menus.

The menus are grouped by usage:

• The Basic Picture menu provides common image adjustments.

• The Advanced Picture menu provides more complex image adjustments.

• The Setup menu provides set-up type adjustments that are not changed often.

• The Status and Service menu provides information about the projector and source.

Basic Picture menu keypad navigation buttons


27

Setup menu Status and Service menu

Basic Picture menu

To adjust the following settings, highlight the setting, press Select, use the up and down arrows to adjust the values, then press Select to confirm the changes.



Brightness

: changes the intensity of the image.

Contrast : controls the degree of difference between the lightest and darkest parts of the picture and changes the amount of black and white in the image.

Sharpness

: (video sources only) changes the clarity of the edges of a video image. Select a sharpness setting.

Color

: adjusts a video image from black and white to fully saturated color.

The color setting applies to video sources only.

Tint

: adjusts the red-green color balance in the image of NTSC video images.

The tint setting applies to NTSC video sources only.

Aspect Ratio

: Aspect ratio is the ratio of the image width to image height. TV screens are usually 4:3. HDTV and most DVDs are 16:9.

Select Auto to have the projector choose the ratio. Choose Native to see the unmodified input with no resizing by the projector. Select 16:9 to watch enhanced widescreen DVDs.

For more information regarding Aspect Ratio, see page 12.

Apply Preset...

: Presets are provided that optimize the projector for displaying computer presentations and video images under certain conditions.

There is also a user-definable preset. To set this preset, adjust the image and select Save User in the Presets menu. You can recall these settings in the future by selecting the User preset.

Keystone : adjusts the image vertically and makes a squarer image. You can also adjust keystone from the keypad.

Digital Zoom : changes the size of projector’s display area. If the display area has been resized by this setting, it can be moved by changing the Horz Shift and Vert Shift settings.

Horz Shift/Vert Shift

: moves the display area horizontally or vertically if its size has been changed by the Digital Zoom setting.

Basic Picture menu increasing keystone

Aspect ratio decreasing keystone

28


BrilliantColor™


take additional 5% Off with coupon code 5PDF delivers enhanced color saturation for bright, true-to-life images. Choose

Normal Look for most video sources and Bright Look for most computer sources.

White Peaking : (video sources only) increases the brightness of whites that are near 100%.

Color Temperature

: changes the intensity of the colors. Select a listed relative warmth value.


Force wide

: when this is off, the analog locking algorithms choose the standard mode resolution (4:3) as the preferred default resolution. When this is on, the analog locking algorithms choose wide mode resolution

(16:10) as the preferred default resolution.

Overscan : removes noise around the video image.

Phase : adjusts the horizontal phase of a computer source.

Sync Threshold

: (progressive signals only) If a hardware device, such as a

DVD player, is not syncing properly with the projector, select this option to help it to sync when connected to the projector.

Tracking : adjusts the vertical scan of a computer source.

Color Space : This option applies to computer and component video sources.

It allows you to select a color space that has been specifically tuned for the input signal. When Auto is selected, the projector automatically determines the standard. To choose a different setting, turn off Auto, then choose RGB for computer sources or choose either REC709 or REC601 for component video sources.

Gamma : select the appropriate gamma from among Video, Film, Bright, and

CRT.

Horizontal/Vertical Position

: adjusts the position of a computer source.

29

Setup menu

Language

Lamp Low Power quieter.

: toggles between on and off. Turn it on to lower the light output of the lamp. This also lowers the fan speed, making the projector

Key Click

: turns the key click sound on or off. When this setting is on, pressing keys on the keypad causes the projector’s speaker to play a “click” sound.

Power Sounds : controls whether the projector makes a sound when powered on and off.

Custom Key

: allows you to assign a different function to the Custom button, allowing you to quickly and easily use the effect. Highlight an effect and press Select to choose a different one.

•

Source Info

: the default action. Shows the Source Info menu.

Auto Source : When this feature is On, the projector automatically finds the active source, checking the selected Power-up Source first. When this feature is Off, the projector defaults to the source selected in Power-up

Source. To display another source, you must manually select one by pressing the Source button on the remote or keypad.

• Projector Info : Shows the Projector Info menu.

•

Aspect Ratio

: toggles among 4:3, 16:9, and Native (see page 12 and

page 28).

• Auto Image

: resets the projector to the source (page 24).

•

Overscan

: removes noise around the image.

• Blank Screen : displays an empty screen.

• Freeze Screen : pauses the projected image.

• Mute : turns off all sound.

•

Source

: cycles through available sources.

Blank Key : Select what to display when the blank key on the remote is depressed: your custom snapshot, a solid color screen (blue, black or white), the factory logo screen, a timer, or test patterns. The timer option is useful for classroom tests or break times during meetings.

Setup menu

Power-up Source : determines which source the projector checks first for active video during power-up.

AC Power On : When this feature is on, the projector automatically turns on when electrical power is connected. This allows control of ceiling mounted projectors with a wall power switch.

HDMI DDC : When this feature is set to On, the projector will support an older DVD player for HDMI port.

Auto Off Time : automatically turns the projector off after no signals are detected for a preset number of minutes. If an active signal is received before the projector powers down, the image will be displayed.

Screen Save Time : automatically blanks the screen with a black color after no signals are detected for a preset number of minutes. The image returns when an active source is detected or a remote or keypad button is pressed.

Video Standard : When this feature is set to Auto, the projector attempts to automatically pick the video standard based on the input signal it receives.

(The video standard options may vary depending on your region of the world.) If the projector is unable to detect the correct standard, the colors may not look right or the image may appear “torn.” If this happens, manually select a video standard by selecting NTSC, PAL, or SECAM from the Video Standard menu.

Closed Captions : controls closed caption display while audio is not muted. If this setting is not off, and audio is not muted, and the source is NTSC and

30

contains captions on the selected channel, then the projector must display caption text overlaid on the image.

press the Select button in order to access the “Wrong PIN” message and reenter the code.

Ceiling Mount : turns the image upside down for ceiling-mounted projection.

Rear Project : reverses the image so you can project from behind a translucent screen.

Auto Keystone : automatically adjusts vertical image.

To enter the PIN at projector startup:

Power up the projector. The “Enter PIN” dialog box appears after the startup screen. Enter the PIN. Use the navigation buttons on the remote or keypad to enter the correct button press sequence. See the description above for instructions.

Prevent PC Screen Saver : prevents your computer from going into Screen

Save mode. The projector must be connected to the PC via a USB cable for this feature to work.

Search Screen

: allows you to display a blank screen instead of the default screen at startup, and when no source is detected.

Take Snapshot...

: Captures the current image and allows it to be used as the search screen image.

Show Messages

: displays status messages (such as “Searching”) in the lowerleft corner of the screen.

Menu Offset : allows you to change the position of the On Screen Display items.

Menu Transparency : allows you to change how much of the projected image behind the menu you can see. As the value increases, more of the image behind the menu is visible.

Magnify Controls : determines whether the select key can be used to change magnify settings when the OSD menu is not visible.

PIN Protect : The PIN (personal identification number) feature allows you to password protect your projector. Once you enable the PIN feature, you must enter the PIN before you can project an image. The default PIN on this projector is Menu-Up-Down-Select-Source. Use the navigation buttons on the remote or keypad to enter the correct 5-button press sequence. When all 5 numbers are entered correctly, press the Select button on the remote or keypad to select OK. If the message “Wrong PIN” appears, verify the code and re-enter it. If you mis-enter a number, you must enter 5 numbers and

To change the PIN:

Select “Change PIN...” in the Setup menu. Enter the existing PIN. Enter the new PIN. You can navigate between OK and Cancel by pressing the up and down buttons on the keypad. Select OK or Cancel by pressing the Select button. Verify the new PIN.

If you lose or forget your custom PIN:

Contact InFocus support. Go to www.infocus.com/support

Computer 2 SCART : Selects SCART connection type between RGB and composite.

Serial Port, Baud Rate : selects the serial port and baud rate.

Serial Port Echo : controls whether the serial port echoes characters.

31

Status and Service menu

Source Info


: a read-only display of current source settings.

Projector Info : a read-only display of current projector settings.

Reset Lamp Hours : resets the lamp hours used counter in the Projector Info menu to zero. Do this only after changing the lamp.

Factory Reset : restores all settings to their default.

Service Code

: only used by authorized service personnel.

Status and Service menu

32

Maintenance



Cleaning the lens

1

Apply a non-abrasive camera lens cleaner to a soft, dry cloth.

• Avoid using an excessive amount of cleaner, and don’t apply the cleaner directly to the lens. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.

2

Lightly wipe the cleaning cloth over the lens in a circular motion.

Using the security lock

The projector has a security lock for use with a PC Guardian Cable Lock

System. Refer to the information that came with the lock for instructions on how to use it.

security lock

33

Replacing the projection lamp



The lamp hours used timer in the Projector Info menu counts the number of hours the lamp has been in use. Twenty hours before the lamp life expires, the message “Change lamp” appears on the screen at startup.

• NOTE : You can order new lamps from www.infocus.com (in select areas), your retailer or your dealer. Only genuine InFocus lamps are tested for use in this projector. InFocus is not liable for the performance, safety or certification of any other lamps. The use of other lamps violates the projector warranty and voids all certification marks on this projector.

1

Turn off the projector and unplug the power cord.

2

Wait 60 minutes to allow the projector to cool thoroughly.

3

Remove the lamp door by (a) removing the screw on the side of the lamp door, (b) sliding the door forward, and (c) lifting the door off.

WARNINGS :

• To avoid burns, allow the projector to cool for at least 60 minutes before you replace the lamp.

• Only genuine InFocus lamps are tested with this projector. Use of other lamps may cause electrical shock and fire.

• Unplug the power cord before replacing the lamp.

• Do not drop the lamp module. The glass may shatter and cause injury.

• Do not touch the glass lamp screen. Fingerprints can obscure projection sharpness.

turn off and unplug projector

Lamp hours

(b)

(c) wait 60 minutes

(a)

34

• Be extremely careful when removing the lamp housing. In the unlikely event that the lamp ruptures, small glass fragments may be generated.

The lamp module is designed to contain most of these fragments, but use caution when removing it. Before replacing a ruptured lamp, clean the lamp compartment and dispose of cleaning materials. Wash hands after lamp replacement. If replacing the lamp while the projector is ceiling-mounted, wear protective eyewear.

Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org.

4

Loosen the captive screw that attaches the lamp housing to the projector. Carefully remove the lamp housing. Dispose of the lamp in an environmentally proper manner.

5

Install the new lamp housing and tighten the screw.

6

Re-attach the lamp connector to the projector.

7

Replace the lamp door by sliding it into place.

8

Plug in the power cord and press the Power button to turn the projector back on.

9

To reset the lamp hour timer, navigate to the Status and Service menu and

select Reset Lamp Hours. See page 32 for details.

loosen screw

35

INDEX

Numerics

16x9 vs 4x3 12

5 volt DC output 4

A

AC Power On 30

Advanced menu 29

Apply Preset 28

Aspect Ratio 12, 28, 30

Audio In Computer connector 9

Audio In connector 13

Audio Out connector 23

Auto Image 30

Auto Off Time 30

Auto Source 30

B

Blank Key 30

Blank Screen 30

Brightness 28

BrilliantColor 29

C cable box 12

Ceiling Mount 30

Cleaning the lens 33

Closed Captions 30

Color Space 29

Color Temperature 29

Computer In connector 9

Connecting external speakers 23 computer 9 video device 12

Connector on Projector 7, 8

Connector panel 4 contacting InFocus 21

Contrast 28

Custom Key 30

Custom key 25 customer service contact information 21

Customizing the projector 26

D

DVDs 28

F

Factory Reset 32 focus 11

Force wide 29

Freeze Screen 30

G

Gamma 29

H

HDMI 1.3 connection 13

HDMI DDC 30

HDTV 6, 28

I

Horizontal 29

Image

Size 5

Optimization 25

K

Key Click 30 keypad buttons 24

Keystone 28 keystone, adjusting 11

L

Lamp hours, resetting 35

Lamp Low Power 30

Language 30 laptop video port activation 10

LEDs 14 leveling foot 11

M

Maintaining the projector 33

Menu button 27 menu usage 27

Monitor Out connector 9

Mute 30

O

Optimizing images 25

Optimizing video 26

36

Overscan 29, 30

P

Phase 29

Picture menu 28

Power connector 9 power cord 9

Power Sounds 30

Power-up Source 30

Presentation features 25

Projection distance 5

Projector

Connector panel 4

Customization 26

Image Size 5 keypad buttons 24

Maintenance 33 menus 27 offset 5

Registering 3 security lock 33

Status indicator panel 14 connecting computers 9 connecting video devices 12 positioning 5 setting up 5 shutting down 14 troubleshooting problems 14

Projector Info 30

R

Rear 31

Registering your projector 3 remote control 22

Reset 32

Resetting the projector 32

RS-232 4

S

Safety Considerations 2

Screen Aspect 12

Screen Save 14, 30

Screen triggers 4

Search Screen 31 security lock 33

Service 32

Service Code 32

Sharpness 28 shutting down the projector 14

Source 30

Source Info 30 speakers, connecting external 23

Status indicator panel 14

S-video connector 13

Sync Threshold 29

T

Tint 28

Tracking 29 troubleshooting 14

TV tuner 12

U

USB 4, 9

V

Vertical 29 video optimizing 26

Video Standard 30

Volume button 23

W warranty 21

White Peaking 29

Z zoom 11

37

InFocus IN310 2, 4, 6, 8, W32 20, W32 40, W32 60 projector User manual

Assistant Bot

Declaration of Conformity

Trademarks

Canada

Agency Approvals

1

Table of Contents

Important Operating Considerations for Safety

Warning:

2

Introduction

Product specifications

Accessories

Online registration

3

Connector panel

5 volt DC output

4

Positioning the projector

Table 1: (IN3102 & IN3104)

Range of distance to the screen for a given screen size

(IN3106/IN3108)

(IN3102 & IN3104)

Table 2: (IN3106/IN3108)

Range of distance to the screen for a given screen size

5

Projector and device connector guide

6

7

8

Connecting a computer source

Required computer connections (DisplayLink or VESA)

Optional computer connections

9

Displaying an image

10

Adjusting the image

11

Connecting a video device

What is Aspect Ratio?

12

Video device connections

Composite video connection

VESA connection

Component video connection

HDMI 1.3 connection

S-video connection

13

Shutting down the projector

Screen Save Time

Auto Off Time

Table 3: Status indicator light behavior and meaning

Turning off the projector

Troubleshooting your setup

14

Startup

Screen

15

16

17

18

COLOR

COLOR

19

20

21

Using the remote control

22

Using the audio

Using the projector’s speakers

Connecting external speakers

23

Using the keypad buttons

24

Optimizing computer images

Presentation features

25

Optimizing video images

Customizing the projector