Kimball 2041381 Interworks EQ - Panel Assembly Instructions

Assembly Instructions

Interworks

®

EQ

Panel Set Up and Panel to Panel Connection

Tools Required

Level, 1 ⁄

2

" Wrench or Channel Locks, Screwdriver

Page 1 of 3

Installation

Important: Level panels throughout installation. If stackable panels are to be installed as well, please, review the Stackable Panel Assembly

Instruction sheets first for preparation tips.

Note: Installation must be in accordance with the National Electrical Code and local codes. Electrically interconnected panels need to be mechanically connected.

These instructions apply to tackable acoustical, glass, and tackable sectional panel. Two people are recommended, start installation at panel intersection at high spot on the floor within layout. If panel configuration includes Traxx®-mounted or wall mounted panel, start installation with that panel.

Step 1

Unpack Panels

• Remove top cap (locate carpet gripper and cable tie)

• Remove panel hinges and wireway covers

There are two ways to create a 90° panel connection:

Top Cap

Step 2

Hinge

• With panels in a straight line

• Adjust glides; panels must be level and aligned to each other

• Connect panels by inserting one hinge

Panel

Hinges

Hinge

Step 2 Alternate

Open Hinge

• With one hinge in panel side rail, open hinge 180° by running a non-marring object down the entire hinge/panel edge

• Remove hinge from panel side rail

Open Entire Length of Hinge

Wireway

Cover

A liggnm

Hinge Opened to 180º

Leveling

Glide

Carpet Gripper

(shipped under Top Cap)

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.

If you have any questions concerning these instructions, please call Kimball Office Customer Service.

Part No. 2041381 Revision E-09

Closed Hinge

(removed)

Panel Side Rail

(top view)

Interworks EQ

Panel Set Up and Panel to Panel Connection,

continued

Step 3

Hinge/Alignment Clip

• Swing wing panel beyond 90°

• Insert alignment clip in stationary panel, gently tap with mallet, if needed

• Pull wing panel back to 90°, engage alignment clip, gently tap with mallet

Stationary

Panel

Corner/L

Alignment Clip

Assembly Instructions

Page 2 of 3

Panel Connection with Alignment Clip Usage

Note: Alignment clips are required for panel stability

Straight

Alignment Clip

Corner/L

90º

Stationary

Panel

Wing Panel

Wing Panel

Corner/L

Alignment Clip

Step 3 Alternate

Panels and Alignment Clip

• Align two panels at 90°

• Adjust glides to level panels

• Insert alignment clip into both panels, gently tap with rubber mallet if needed

• Fully insert hinge, double check levelness of panels

Corner/L

Alignment Clip

Hinge

Straight/T 4-Way

Step 4

In-Line Straight

Connection

• Insert straight alignment clip

• Adjust leveling glides

120º/3-Way

Step 5

Connect Panels

• Fully insert panel hinges

• Plumb/level panels

• Install in-line and connector top caps

• Install panel top caps

• Once location of station is approved, install (1) carpet gripper per panel

Panel

Hinge

Straight

Alignment

Clip

Carpet Gripper

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.

If you have any questions concerning these instructions, please call Kimball Office Customer Service.

Part No. 2041381 Revision E-09

120º/V

Interworks EQ

Side Rail Removal

Tools Required

Phillips Screwdriver

Loosening Panel Side Rail

• Remove end trim if installed. (Figure A.)

• Remove side rail screws. (Figure B).

• When re-installing side rail screws, do not over-torque or side rail may deform. (Figure C).

Figure A

Figure B

Side Rail

Screws

Assembly Instructions

Page 3 of 3

End Trim

Figure C

Side Rail

Frame

Over Torquing

May Bow Side Rail

Proper product installation, in accordance with these instructions, is the responsibility of the installing agent.

If you have any questions concerning these instructions, please call Kimball Office Customer Service.

Part No. 2041381 Revision E-09