PDF version - Millhill Supplies Ltd.

PDF version - Millhill Supplies Ltd.
1
Millhill Supplies Ltd.
Spare parts for UK manufactured lathes
Catalogue: Sherline Accessories
This page contains a price list of all Sherline accessories that we sell.
Other price lists:
●
●
●
Catalogue: Sherline Accessories
Catalogue: Sherline Lathes
Catalogue: Sherline Milling Machines
Contents
●
●
SHERLINE ACCESSORIES
SHERLINE CHUCKS
SHERLINE ACCESSORIES
Part Number Part
Weight
1012
SENSITIVE DRILLING ATTACHMENTThreads onto mill
spindle. Spring loaded 5/32" chuck is pulled down by
hand using a bearing supported knurled collar. Provides
quick action and great "feel" when drilling small holes.
0.91kg £111.00
2lbs
1074
STEADY RESTSupports the end of long work for center 0.34kg
drilling
0.75lbs
£40.25
1090
FOLLOWER RESTSupports thin work, keeps it from
deflecting away from the cutter, moves with the lathe
saddle to "follow" the work
0.34kg
0.75lbs
£70.50
1160
WW COLLET SETP/N 1161 included in set. Collets are 0.23kg
1178 (metric) like small, individually sized chucks for holding a
0.5lbs
specific diameter tool or material. WW collets have a
hole through the collet and drawbar to accept long
material. Traditionally used by watch and clock makers.
Sherline WW collets have a .312-.313 body size and
.275-40 thread.
£90.75
116000
WW COLLET BLANK, Large Head
0.02kg
0.05lbs
£11.25
116000+size
WW COLLET, CUSTOM SIZECustom size collets can 0.02kg
be ordered in sizes from .050" to .320" or 1.28 mm to
0.05lbs
8.13 mm. For example, a custom collet might be ordered
as 116000 .100" or 116000 2.75 mm.) Custom collets
are not laser engraved with size information. Allow 3
weeks for delivery.
£40.25
Millhill Supplies Ltd.
- 1 / 17 -
Cost
14.02.2017
2
1160001
WW COLLET BLANK, Small Head
0.02kg
0.05lbs
£11.25
116001
1/64″ WW COLLET
0.02kg
0.05lbs
£40.25
116002
1/32″ WW COLLET
0.02kg
0.05lbs
£32.50
116003
3/64″ WW COLLET
0.02kg
0.05lbs
£21.50
116004 116020
WW COLLETS from size 1/16″ to 5/16″ by 64ths.The 0.02kg
part number is given as 1160__ plus the number of 64ths 0.05lbs
to denote size. For example, 13/64" is P/N 116013 and a
1/4" collet (16/64") is P/N 116016.
£17.30
1161
WW COLLET ADAPTER & DRAWBARIncluded in
collet set. Adapts WW taper to #1 Morse taper of
Headstock
0.23kg
0.5lbs
£50.50
1162
DELUXE WW COLLET SET (Inch)17 collets, adapter,
drawbar, pot chucks, knockout bar, etc. in wooden case
1.36kg £277.25
3lbs
1163
8.0 MM COLLET ADAPTER & DRAWBARWW collets 0.23kg
vary somewhat depending on manufacturer. This
0.5lbs
adapter holds those with a .314-.315 body size
1164
WW COLLET FIXTUREAllows WW collets with .312-.313 0.45kg £106.00
body to be held on face of rotary table or mill table.
1lbs
1165
8.0 MM COLLET FIXTUREAllows WW collets with
.314-.315 body to be held on face of rotary table or mill
table.
1170
OAK WW COLLET STORAGE BOXA high quality storage 0.45kg
box that holds up to 22 WW collets plus collet pot
1lbs
chucks, drawbar, knockout bar and WW collet adapter.
Beveled corners, brass hardware, satin lacquer finish.
£30.25
1171
OAK WW COLLET STORAGE BOXA high quality
0.45kg
storage box that holds up to 96 WW collets. Beveled
1lbs
corners, brass hardware, oak insert with 96 holes, satin
lacquer finish.
£35.25
117803
.3 mm WW COLLET
0.02kg
0.05lbs
£40.25
117804
.4 mm WW COLLET
0.02kg
0.05lbs
£40.25
117805 117808
WW COLLETS from size .5mm through .8 mm by .1 0.02kg
mm increments.The Part number is given as 11780
0.05lbs
plus the collet size in .1 mm. For example, a .6 mm collet
would be P/N 117806
£40.25
117809 117814
WW COLLETS from size .9mm through 1.4 mm by 0.02kg
.1 mm increments.The part number is given as 11780_ 0.05lbs
or 1178__ plus the collet size in .1 mm. For example, a
1.1 mm collet would be P/N 117811.
£32.50
117815 117880
WW COLLETS from size 1.5 mm through 8.0 mm by 0.02kg
.1 mm increments.The part number is given as 1178__ 0.05lbs
plus the collet size in .1 mm. For example, a 6.4 mm
collet would be P/N 117864.
£17.30
1179
DELUXE WW COLLET SET (Metric)14 collets, pot
chucks, etc. in wooden case. P/N 1161 included in set
Millhill Supplies Ltd.
- 2 / 17 -
£55.50
0.45kg £116.00
1lbs
1.36kg £247.00
3lbs
14.02.2017
3
1180
COMPLETE METRIC WW COLLET SETThe set is
contained in a P/N 1171 oak collet box with 96-hole oak
insert.
1.82kg £942.50
4lbs
1182
BULLNOSE LIVE CENTERSupports tubing or stock
with a large end hole when turning between centers.
Dual preloaded bearings.
0.34kg
0.75lbs
1185
1184 (metric)
VERTICAL MILLING TABLEMounts to lathe or mill table 1.14kg £121.00
to move work up and down. Has 2.25" of vertical travel 2.5lbs
and 8" long table.
1187
CHUCK-TO-T-SLOT ADAPTERAllows 3- or 4-jaw
chuck to be quickly screwed to mill table.
0.03kg
0.06lbs
£7.75
1191
LIVE CENTERBall bearings allow center to rotate with
part to reduce friction when turning between centers
0.11kg
0.25lbs
£40.25
1201
ADJUSTABLE LIVE CENTERBall bearing live center
adjusts for perfect centering of headstock and tailstock
0.23kg
0.5lbs
£65.50
1202
ADJUST. TAILSTOCK CHUCK ARBORAllows perfect
centering of tailstock chuck in relation to headstock
0.23kg
0.5lbs
£45.50
1203
ADJUST. TAILSTOCK TOOL HOLDERAllows perfect
centering of round tools held in tailstock
0.23kg
0.5lbs
£45.50
1206
ADJUST. TAILSTOCK 1″ DIE HOLDER w/ 13/16″
bushingAllows perfect centering of 1" or 13/16"
threading dies
0.23kg
0.5lbs
£60.50
1220
TAILSTOCK SPINDLE EXTENDERDesigned for lathes 0.23kg
built before July, 1996 to extend reach of tailstock
0.5lbs
spindle over table. Not needed on newer lathes
£40.25
1230
#0 MORSE ARBOR TO 3/4-16 CHUCK THREAD
ADAPTERAllows a 3- or 4-jaw chuck to be mounted on
the tailstock spindle
£40.25
0.23kg
0.5lbs
£81.00
1270
COMPOUND SLIDERedesigned, Replaces P/N 1080.
0.45kg £126.00
1280 (metric) An alternate and more traditional way of turning tapers 1lbs
1272
COMPOUND SLIDE RISER BLOCKRaises compound
0.23kg
slide about 1" for use on front side of crosslide with riser 0.5lbs
blocks in place on lathe
£35.25
1288
RISER ROCKER TOOL POSTTaller tool post for use
with riser blocks in place on the lathe
0.23kg
0.5lbs
£40.25
1289
RISER 3/8″ INSERT TOOL POSTTaller tool post for
0.23kg
holding 3/8" shank tools with riser blocks in place on the 0.5lbs
lathe.
£40.25
1290
STEADY REST RISERLifts steady rest to match
0.11kg
headstock when spacer block is in place. Used mainly by 0.25lbs
those who leave spacer blocks in place at all times on
their lathe.
£50.50
1291
SPACER BLOCK KITLifts headstock 1.25" to allow parts 0.68kg
up to 6" diameter to be turned. Includes extended riser 1.5lbs
rocker tool post
£70.50
1292
TAILSTOCK RISER BLOCKLifts tailstock 1.25" for
turning between centers with headstock riser block in
place
0.45kg
1lbs
£50.50
1296
CUTOFF TOOL HOLDER RISER BLOCKLifts cutoff tool 0.23kg
P/N 3002 for use with riser blocks in place. Used with tool 0.5lbs
upside down on back side of crosslide table.
£50.50
Millhill Supplies Ltd.
- 3 / 17 -
14.02.2017
4
1297
MILL HEADSTOCK SPACER BLOCKSame as riser
block for lathe, but without tool post. Adds 1.25" of
throat distance when milling
0.34kg
0.75lbs
£45.25
1300
MILL COLUMN SPACER BLOCKRaises column base 2"
for greater Z-axis clearance. Includes longer bolts for
mounting.
0.68kg
1.5lbs
£40.25
2045
HEX AND OCTAGON INDEX BLOCK SETFits in mill
vise to allow simple indexing of 2, 3, 4, 6 or 8 sides or
hole patterns
0.91kg
2lbs
£60.50
2049
SPINDLE HANDWHEELUsed to rotate the headstock
spindle much like the large handwheel on a sewing
machine is used
0.68kg
1.5lbs
£45.25
2083
WW COLLET 1″ BLANKMake your own custom tool
holder or collet that is held with the WW adapter and
drawbar
0.03kg
0.06lbs
£30.25
2085
WW COLLET TAILSTOCK ADAPTERUse with P/N 1203) 0.11kg
(Allows WW collets to be held in the tailstock
0.25lbs
£55.25
2086
8mm COLLET TAILSTOCK ADAPTERUse with P/N
1203
0.11kg
0.25lbs
£60.50
2090
8.0mm COLLET TO 3/4-16 THREADFor mounting
Sherline chuck on watchmaker's or jeweler's lathe that
takes 8.0mm collets
0.23kg
0.5lbs
£40.25
2091
10mm “D” COLLET TO 3/4-16 THREADFor mounting 0.23kg
Sherline chuck on watchmaker's or jeweler's lathe that 0.5lbs
takes 10mm D collets, not for use on Sherline lathe.
£45.25
2092
8.0mm COLLET TO 3/8-24 THREADFor mounting
chuck with 3/8-24 thread on watchmaker's or jeweler's
lathe that takes 8.0mm collets, not for use on Sherline
lathe.
0.23kg
0.5lbs
£40.25
2093
10.0mm COLLET TO 3/8-24 THREADFor mounting
0.23kg
chuck with 3/8-24 thread on watchmaker's or jeweler's 0.5lbs
lathe that takes 10mm D collets, not for use on Sherline
lathe.
£45.25
2094
CLOCKMAKER’S GEAR CUTTING ARBOR, 7.0mm to
Morse #1Arbor for use on watchmaker or jeweler's
lathes to hold round gear cutter, Not for use on Sherline
lathe
0.23kg
0.5lbs
£60.50
2095
CLOCKMAKER’S GEAR CUTTING ARBOR, 7.0mm 0.23kg
to 10mm “D” ColletArbor for use on watchmaker's or 0.5lbs
jeweler's lathes to hold round gear cutter. not for use on
Sherline lathe
£60.50
2096
CLOCKMAKER’S GEAR CUTTING ARBOR, 7.0mm to 0.23kg
8.0 mm WW ColletArbor for use on watchmaker's or
0.5lbs
jeweler's lathes to hold round gear cutter, not for use on
Sherline lathe
£60.50
2100
WW 3/4″ COLLET POT CHUCKCollet pot chucks are 0.03kg
like small chucks custom turned to hold a particular
0.06lbs
part. The part is held in a depression turned in the
surface of the pot chuck and does not go all the way
through. Includes dowel pin to clamp on while turning to
size.
£25.25
Millhill Supplies Ltd.
- 4 / 17 -
14.02.2017
5
2101
WW 1″ COLLET POT CHUCKSee 2100
0.03kg
0.06lbs
£27.25
2102
WW 1-1/4″ COLLET POT CHUCKSee 2100
0.03kg
0.06lbs
£30.25
2103
10mm 3/4″ COLLET POT CHUCKNot for use on Sherline 0.05kg
lathe
0.12lbs
£35.25
2104
10mm 1″ COLLET POT CHUCKNot for use on
Sherline lathe
0.05kg
0.12lbs
£40.25
2105
10mm 1-1/4″ COLLET POT CHUCKNot for use on
Sherline lathe
0.05kg
0.12lbs
£45.25
2106
LIVE CENTER-TO-8mm COLLETA live center for
watchmaker's or jeweler's lathes.
0.11kg
0.25lbs
£75.50
2107
LIVE CENTER-TO-10mm COLLETA live center for
watchmaker's or jeweler's lathes.
0.11kg
0.25lbs
£75.50
2110
W.R. SMITH WATCHMAKER’S T-RESTUsed on
0.45kg £201.50
Sherline lathes to support a hand-held "graver", a
1lbs
traditional watchmaker's tool. Turns Sherline lathe into
a first class watch or clock maker's lathe. Designed by
famed craftsman W.R. Smith. Graver-making
instructions included.
2200
RADIUS CUTTING ATTACHMENTFor cutting ball ends,
convex and concave radii on ends of parts and even
complete balls
2250
QUICK CHANGE TOOL POST w/ 3 holdersSaves time 1.36kg £262.00
when changing tools. Holders included for 1/4" cutter, 3lbs
round boring tool and cutoff tool. Cutting tools not
included.
2251
QUICK CHANGE TOOL POST RISERBrings quick0.8kg
change tool post up to proper centerline height when
1.75lbs
using a riser block under the headstock for cutting larger
diameters.
£50.50
2256
RIGHT-HAND 35° CARBIDE INSERT TOOL
HOLDER (Includes one 55° insert)Use in 7600 tool
post. Carbide is used to cut hard-to-machine materials
like stainless steel
0.11kg
0.25lbs
£45.25
2257
LEFT-HAND 35° CARBIDE INSERT TOOL
0.11kg
HOLDERIncludes one 55° insert) (Use in 7600 tool post. 0.25lbs
Carbide is used to cut hard-to-machine materials like
stainless steel
£45.25
2258
PAIR OF RIGHT- and LEFT-HAND 35° INSERT
0.23kg
TOOL HOLDERSIncludes one 55° insert per holder)
0.5lbs
(Replacement inserts, P/N 7605) (Save £19.50 by buying
both LH and RH tools together
£70.50
2259
80° INSERT 3/8″ ROUND BORING TOOL, 1/2″ min.
hole, carbide insert includedUse w/ P/N 7600 tool
post
0.07kg
0.15lbs
£60.50
2260
55° INSERT 3/8″ ROUND BORING TOOL, 3/4″ min. 0.07kg
hole, carbide insert includedUse w/ P/N 7600 tool
0.15lbs
post
£60.50
2261
PAIR OF 80° (P/N 2259) AND 55° (P/N 2260) 3/8″
ROUND BORING TOOLS w/ inserts
£95.75
Millhill Supplies Ltd.
- 5 / 17 -
0.45kg £121.00
1lbs
0.11kg
0.25lbs
14.02.2017
6
2280
1/4″ QUICK-CHANGE TOOL BIT HOLDER (Incl. w/
2250)
0.45kg
1lbs
£60.50
2285
3/8″ QUICK-CHANGE BORING TOOL HOLDER (Incl.
w/ 2250)
0.45kg
1lbs
£60.50
2290
QUICK-CHANGE CUTOFF TOOL HOLDER (Incl. w/
2250)
0.45kg
1lbs
£80.50
2295
CARBIDE INSERT HOLDER for QUICK-CHANGE TOOL 0.45kg
POST
1lbs
£90.75
3001
POWER FEED (120V.) (for 240V. see P/N
3011)Single direction motor drives lathe leadscrew .9"
per minute to provide smooth final cut on long parts.
Not designed for use with thread cutting attachment.
2.27kg
5lbs
£90.75
3002
CUTOFF TOOL & HOLDERFor cutting off work piece
0.11kg
from the raw stock from which it was turned. Often called 0.25lbs
a "parting tool".
£50.50
3003
TWO-POSITION TOOL POSTHolds two 1/4" cutting
tools for quicker tool changes
0.11kg
0.25lbs
£16.25
3004
KNURLING TOOL HOLDERMakes knurled finishes.
0.11kg
Includes one set of spiral knurls. Other sizes and patterns 0.25lbs
available
£75.50
3005
1/4″ SQ. HIGH SPEED STEEL TOOL BLANKSharpen 0.03kg
yourself on a bench grinder for standard or custom0.06lbs
shaped tools
£3.25
3006
CARBIDE TOOL SET (3 PC) (LH, RH, 60°
0.17kg
THREADING)Carbide tips are brazed to 1/4" tool shanks. 0.38lbs
For cutting hard materials
£20.25
3007
HIGH SPEED STEEL TOOL SET (3 PC) (LH, RH,
BORING)Pre-sharpened to save you time. For cutting
most materials
0.05kg
0.12lbs
£25.25
3008
TWO-POSITION TOOL POST, 5/16″ – 3/8″Holds 5/16"
tool on one side, 3/8" on other side. Allows use of tools
other than 1/4"
0.11kg
0.25lbs
£25.25
3009
CUTTING TOOL HEIGHT GAUGEUsed to assure tool 0.11kg
tip on resharpened tools is set to proper centerline
0.25lbs
height. Works with both regular or riser toolpost
£20.25
3011
POWER FEED (240V)See P/N 3001
3012
HOLD-DOWN SETSimple strap clamp set for clamping 0.17kg
parts to table for milling. Includes 2 clamps, T-nuts and 0.38lbs
assorted length bolts
£25.25
3013
STEP BLOCK HOLD-DOWN SETThis is a smaller version 0.45kg
of the sets used on most full-size mills. Quicker to use
1lbs
than 3012 and holds larger parts. Stepped blocks
interlock to adjust height quickly. Spare block included to
be cut to custom sizes
£40.25
3015
TOGGLE SWITCH DUST SEALUse to keep fine dust
0.03kg
out of speed contorl on/off switch when cutting brass or 0.06lbs
wood
£8.75
Millhill Supplies Ltd.
- 6 / 17 -
2.27kg £102.75
5lbs
14.02.2017
7
3016
CUTOFF TOOL REAR MOUNTING BLOCKAllows 3002
cutoff tool to be mounted on "back" side of crosslide
where it is out of the way and can be left in place for
easy parting off. Cutoff blade mounts upside down for
use in this position
0.05kg
0.12lbs
£15.25
3017
CROSSLIDE ACCESSORY PLATEStrengthens and
protects lathe table when used for milling with vertical
milling column. Not for use during lathe operations as
tool post height will be incorrect.
0.45kg
1lbs
£40.25
3018
REAR MOUNT CUTOFF TOOL AND HOLDER
0.11kg
0.25lbs
£50.50
3020
SHERLINE “T” DRIVER5/32" hex driver with T-handle 0.05kg
adjusts majority of 10-32 screws on Sherline tool. Easy 0.12lbs
to find on your bench.
£6.25
3021
CENTER DRILL SET (3 PC., #1, #2, #3 doubleended)Center drills don't wander off center when
starting holes. 60° tip makes proper hole to match dead
or live center tips for turning between centers
0.03kg
0.06lbs
£16.25
3035
SPUR DRIVERA quick way to drive wood parts when
turning between centers.
0.11kg
0.25lbs
£25.25
3038
WOOD TOOL REST (3″ & 5″ REST)Supports hand-held 0.34kg
wood cutting tools for wood turning
0.75lbs
£55.50
3047
EXTENDED WOOD TOOL REST SET (For use w/
0.11kg
1291)Like 3038 only with longer shafts to match height 0.25lbs
of headstock with riser block in place
£60.50
3050
3053 (metric)
VERTICAL MILLING COLUMNConverts your lathe into a 3.64kg £151.25
3-axis mill in less than 30 seconds.
8lbs
3050-CNC
3053-CNC
(metric)
VERTICAL MILLING COLUMN, CNC
READYConverts lathe into a 3-axis mill. Stepper motor
mount is ready to accept NEMA 23 frame size stepper
motor for CNC control
4.09kg £253.00
9lbs
3052
FLY CUTTERFor quickly milling large, flat surfaces.
0.23kg
0.5lbs
£35.25
3054
BORING HEADFor enlarging holes to a precise inside
diameter, uses 3/8" round boring tools
0.23kg
0.5lbs
£70.50
3055
MORSE #1 BLANKTurn on lathe and/or mill slots to
make your own custom fly cutter, slitting saw holder or
special tool holder
0.23kg
0.5lbs
£16.25
3056
T-NUTS, 10/32 (Set of 10)
0.03kg
0.06lbs
£8.25
3057
ROCKER TOOL POSTRocking insert with two screws
0.11kg
allows adjustment of tool tip height for accurate turning. 0.25lbs
Eliminates shimming. Included on Model 4400/4410
lathes
£30.25
3058
4-JAW HOLD DOWN SETTwo angle clamps with Tnuts to clamp 4-jaw vise to any position on mill table.
Included with 3551 mill vise
0.05kg
0.12lbs
£6.25
3060
3090 (metric)
MILLING COLLET SET (3 PC)(1/8", 3/16", 1/4") Milling
collets have a #1 Morse taper and are pulled into the
headstock with a drawbolt. They do not have a through
hole like WW collets. They are used to hold specific size
end mills or cutters.
0.05kg
0.12lbs
£45.50
Millhill Supplies Ltd.
- 7 / 17 -
14.02.2017
8
3061
BORING TOOL—Max. Depth .600, Min. Hole
1/4″)Use w/ P/N 3054 boring head
0.05kg
0.12lbs
£15.25
3063
BORING TOOL—Max. Depth 1″, Min. Hole 5/16″Use
with P/N 3054 boring head
0.05kg
0.12lbs
£15.25
3064
BORING TOOL—Max. Depth 1.5″, Min. Hole
5/16″Use w/ 3054 boring head
0.05kg
0.12lbs
£18.25
3065
SLITTING SAW HOLDERHolds small, round sawblades
for cutting thin slots
0.11kg
0.25lbs
£40.50
3070
2.5″ Dia. x 1-5/16″ STEEL BLANK (Chuck body) w/
3/4-16 threadA billet of 12L14 steel threaded for the
Sherline spindle, ready to turn it into whatever tool or
part you need. A blank canvas for machinists.
0.91kg
2lbs
£25.25
3074
Tool holder for 1/4″ or 3/8″ Jacobs drill chucks3/4- 0.23kg
16 female thread to 3/8-24 male thread adapter replaces 0.5lbs
#1 Morse arbor to allow drill chucks to be threaded on to
outside thread of spindle to speed up tool changes on
CNC machines. No variation in drill length when changing
tools back and forth. Cannot be used with 5/32" Jacobs
chucks as they do not have a threaded back.
£35.25
3075
5/16″ END MILL HOLDER
0.23kg
0.5lbs
£30.25
3076
6.0mm END MILL HOLDER
0.23kg
0.5lbs
£30.25
3077
8.0mm END MILL HOLDER
0.23kg
0.5lbs
£30.25
3078
10.0MM END MILL HOLDERMost common size metric
tool holder
0.23kg
0.5lbs
£30.25
3079
3/8″ END MILL HOLDERMost common size inch tool
holder. 3/8" end mills are available from many sources
and are, therefore, the least expensive and available in
the largest selection.
0.23kg
0.5lbs
£30.25
3080
END MILL SET (1/4″ SHK) (1/8″, 3/16″, 1/4″)
0.03kg
0.06lbs
£30.25
3087
3/32″ MILL COLLET
0.03kg
0.06lbs
£20.25
3089
5/32″ MILL COLLET
0.03kg
0.06lbs
£20.25
3090
3-PC. METRIC MILL COLLET SET w/ 3.0, 4.0 and
6.0 mm colletsSee P/N 3060 for inch version set and
description.
0.07kg
0.15lbs
£45.50
3091
7/32″ MILL COLLET
0.03kg
0.06lbs
£20.25
3092
3.0MM MILL COLLET
0.03kg
0.06lbs
£16.50
3093
4.0MM MILL COLLET
0.03kg
0.06lbs
£16.50
3094
6.0MM MILL COLLET
0.03kg
0.06lbs
£16.50
3095
1/8″ MILL COLLET
0.03kg
0.06lbs
£16.50
Millhill Supplies Ltd.
- 8 / 17 -
14.02.2017
9
3096
3/16″ MILL COLLET
0.03kg
0.06lbs
£16.50
3097
1/4″ MILL COLLET
0.03kg
0.06lbs
£16.50
3098
MILL COLLET (Special Order .125 to .312)Allow 3
weeks delivery
0.03kg
0.06lbs
£50.50
3100
THREAD-CUTTING ATTACHMENTBeing able to cut
1.36kg £126.00
threads on your lathe frees you from the expense of
3lbs
purchasing a lot of expensive taps and dies for nonstandard size threads. Cut just about any thread, inch or
metric, using this set of change gears. Hand crank wheel
included
3200
INDEXING ATTACHMENTIndexes in 5° increments,
3.64kg £201.50
uses rack gear to turn rotation into measurable linear
8lbs
movement for divisions other than 5° multiples. Includes
base and tailstock.
3217
GEAR TOOTH CUTTER HOLDER & HSS BLANKGrind
0.23kg
gear shape into tool blank and use on mill in conjunction 0.5lbs
with indexing attachment or rotary table to cut your own
gears.
£35.25
3230
MILL ARBOR-7/8″ DIA. (Short)Holds round mill
cutters
0.23kg
0.5lbs
£50.50
3231
MILL ARBOR-7/8″ DIA. (Long)Holds round mill cutters 0.23kg
0.5lbs
£50.50
3235
MILL ARBOR-1″ DIA. (Short)Holds round mill cutters 0.23kg
0.5lbs
£50.50
3236
MILL ARBOR-1″ DIA. (Long)Holds round mill cutters
0.23kg
0.5lbs
£50.50
3306
STD. HEADSTOCK, DC MOTOR AND SPEED
CONTROLComplete, self-contained drive unit with
pulleys designed to turn the spindle at speeds up to
2800 RPM. Alternate pulley position provides more
torque and a maximum spindle speed of 1400 RPM.
Operates on any current 100VAC to 240VAC, 50 or 60
Hz.
4.55kg £322.50
10lbs
3307
10,000 RPM HEADSTOCK, DC MOTOR AND SPEED
4.55kg £403.25
CONTROLComplete, self-contained drive unit with
10lbs
pulleys designed to turn the spindle at speeds up to
10,000 RPM. Alternate pulley position provides more
torque and a maximum spindle speed of 2200 RPM.
Operates on any current 100VAC to 240VAC, 50 or 60 Hz.
3400
OVERSIZE HANDWHEEL2.5" diameter for easier
3410 (metric) cranking
0.05kg
0.12lbs
£15.25
2″ ADJUSTABLE ZERO HANDWHEELMill Y-axis or lathe 0.11kg
crosslide
0.25lbs
£35.25
3440
2.5″ ADJUSTABLE ZERO HANDWHEELMill Y-axis or 0.11kg
3450 (metric) lathe leadscrew
0.25lbs
£40.50
3460
3465 (metric)
£45.50
3420
3430 (metric)
Millhill Supplies Ltd.
2.5″ ADJUSTABLE ZERO HANDWHEELW/Thrust &
Bearing Set for Mill Z-axis
- 9 / 17 -
0.11kg
0.25lbs
14.02.2017
10
3480
VERTICAL MILLING COLUMN W/ADJ.
3485 (metric) HANDWHEELTurns lathe into a mill in less than 30
seconds. Normally used with 4500 or 4400 lathes to
match adj. Zero handwheels.
3.64kg £171.25
8lbs
3500
ROTARY COLUMN ATTACHMENTAllows mill column to 0.8kg
be swung up to 90° to either side for angled drilling.
1.75lbs
£81.00
3551
MILLING VISEHolds work for milling. Looks similar to 1.14kg
a drill press vise, but jaw pulls down and in to keep
2.5lbs
parts from lifting during milling. Precise jaws and body
can be squared up with table.
£75.50
3559
90° ANGLE PLATEMounts parts 90° to table for milling
1.82kg £101.00
4lbs
3560
MILL TOOLING PLATEProtects mill table, pre-drilled
hole pattern makes it easy to clamp parts, mount mill
vise or rotary table to mill.
1.14kg
2.5lbs
3570
ROTATING MILL VISE BASEHolds mill vise while
0.45kg £101.00
allowing it to be rotated 360° using laser engraved scale 1lbs
for angle reference
3575
ROTATING MILL VISE BASE AND MILL VISE (P/N
3551)Save by buying vise and base at same time
1.14kg £166.50
2.5lbs
3580
3585 (metric)
MULTI-DIRECTION DELUXE VERTICAL MILLING
COLUMNTurns your lathe into an 8-direction mill in 30
seconds
5.91kg £378.00
13lbs
3700
4″ PRECISION ROTARY TABLE72:1 worm gear
3.64kg £272.25
divides a circle into 3600 parts without interpolation.
8lbs
Used for indexing radial hole patterns or milling radii or
indexed flats. Used on 3701 or 3750 to index for cutting
gear teeth. A mill with a rotary table is an extremely
potent combination, make virtually any part possible,
with size being the only limitation
3700-CNC
4″ PRECISION ROTARY TABLE, CNC-READYIncludes
stepper motor mount ready for application of your own
stepper motor and CNC controls. Handwheel also
included
5kg
11lbs
3701
RIGHT ANGLE ATTACHMENT (For use with P/N
3700)Mounts rotary table perpendicular to mill table
1.36kg
3lbs
£75.50
3702
RIGHT ANGLE ADJUSTABLE TAILSTOCKFor use with
0.91kg
P/N 3700. Aligns with center of rotary table when
2lbs
mounted on 3701. Supports arbor shaft used to hold gear
blanks when cutting teeth.
£75.50
37091
12 mm to 3/8-16 ADAPTERAllows Chuck with 12 mm 0.11kg
thread to be mounted to Sherline rotary table P/N 3700 0.25lbs
£18.75
37092
14 mm to 3/8-16 ADAPTERAllows Chuck with 14mm
thread to be mounted to Sherline rotary table P/N 3700
0.11kg
0.25lbs
3750
TILTING ANGLE TABLEMount part, mill vise, chucks
or rotary table to mill any angle from 0° to 90°. In 90°
position, holds rotary table at same height as 3701,
eliminating the need for that part
1.14kg £111.00
2.5lbs
4017U
MILL SADDLE LOCKING LEVER UPGRADEAllows Z0.23kg
4117U (metric) axis leadscrew to be locked with a lever on the leadscrew 0.5lbs
instead of tightening a screw with a hex wrench.
Standard on all mills after 1998
Millhill Supplies Ltd.
- 10 / 17 -
£60.50
£322.50
£8.75
£25.25
14.02.2017
11
4017Z
4117Z
(metric)
CNC MILL ANTIBACKLASH ADJUSTER
0.23kg
UPGRADEAllows the Z-axis locking lever to be
0.5lbs
positioned in partially locked positions to reduce
backlash to as little as .001". Standard on CNC mills
after 2/04. Can be installed as an option on any Sherline
mill.
£35.25
4150
15″ LATHE VINYL COVERProtect your 4000-series lathe 0.11kg
from dust and grit
0.25lbs
£12.25
4151
24″ LATHE VINYL DUST COVERProtect your 4400series lathe from dust and grit
0.11kg
0.25lbs
£14.25
4335
10,000 RPM PULLEY CONVERSIONHigh speed position 0.45kg
allows motor to turn spindle at a maximum of 10,000
1lbs
RPM. Second belt position provides more torque and a
maximum of 2200 RPM. New 2-piece standoff replaces
standard motor standoffs. Installs in about 10 minutes.
£80.75
4360
CHIP GUARDClear shield contains flying chips. Pivots
out of the way when not needed. Not a substitute for
safety glasses
0.23kg
0.5lbs
£15.25
4417Z
4417ZM
(metric)
CNC LATHE BACKLASH ADJUSTERInstalls on
0.23kg
leadscrew to provide a way to reduce backlash during
0.5lbs
CNC operations. Similar to the 4017Z lock developed for
the mill, it uses a lever which is tightened against the
saddle nut to control backlash. A positioning arm holds
the locking lever in any desired position. Installed on all
CNC-ready lathes as of 5/04. Can be installed as an
option on any Sherline lathe.
£37.75
5011U
5111U
(metric)
MILL X and Y AXIS STAR GEAR BACKLASH
0.05kg
UPGRADEInstalls on mills made after 1997 when the
0.1lbs
pointer style backlash lock was replaced with the star
gear type lock and up until July, 2004 when this change
was incorporated into regular production. Includes new
star gears and leadscrew nuts with finer teeth for mill X
and Y axis plus new button head screws to hold the
locking gear.
£9.75
5150
MILL VINYL COVERProtects your 2000-series mill from
dust and grit
0.11kg
0.25lbs
£14.25
5151
MILL VINYL COVERProtects your 2000-series mill
from dust and grit
0.11kg
0.25lbs
£16.50
5200
5210 (metric)
XY BASE (10″) (Inch)Add a 3050 vertical milling
7.73kg £262.00
column and the motor/speed control from your lathe and 17lbs
you have a model 5000 mill
5200-CNC
5210-CNC
(metric)
XY BASE (10″) CNC READY (Inch) w/ 2 stepper
motor mountsStepper motors and CNC controls not
included.
9.09kg £438.50
20lbs
5201
5211 (metric)
XYZ BASE (10″) (Inch)Add the motor/speed control
from your lathe and you have a model 5000 mill
11.82kg £463.75
26lbs
5201-CNC
5211-CNC
(metric)
XYZ BASE (10″) CNC READY (Inch) w/ 3 stepper
motor mountsStepper motors and CNC controls not
included.
12.27kg £715.75
27lbs
Millhill Supplies Ltd.
- 11 / 17 -
14.02.2017
12
5220
5225 (metric)
XY BASE (10″) W/ ADJUST. HANDWHEELSAdd a
8.64kg £337.75
vertical milling column with adjustable handwheels and 19lbs
the motor/speed control from your lathe and you have a
complete model 5500/5510 mill
5230
XYZ BASE (10″ W/ ADJUST. HANDWHEELSAdd the
5235 (metric) motor/speed control from your lathe and you have a
complete model 5500/5510 mill
11.82kg £519.25
26lbs
5300
HOME MACHINIST’S HANDBOOK by Doug Briney275 0.91kg
pages, B/W, uses Sherline tools in all the setup
2lbs
examples, project plans included
£21.00
5301
TABLETOP MACHINING by Joe MartinThe ultimate 1.36kg
miniature machining book by Sherline's owner. All color, 3lbs
8-1/2 x 11, 400+ photos, 200+ illustrations. Third
printing, 11/01 includes 8 more pages and several new
photos.
£40.50
5325
SHERLINE TOOLS & ACCESSORIES CATALOG, 6th
Edition48-page color catalog shows tools and
accessories plus tells briefly how each is used. Current
price lists enclosed.
0.23kg
0.5lbs
£3.00
5326
SHERLINE ASSEMBLY AND INSTRUCTION GUIDE, 0.23kg
4th Edition44-page color instruction book included
0.5lbs
with new machines. A good basic course in machining
£3.00
5327
SHERLINE SHOP GUIDE144 pages, B/W, 8.5 x 11"
1.36kg
perfect bound book incorporates illustrated instructions 3lbs
from all of Sherline's major accessories into one volume.
£10.00
5328
STEAM ENGINE VIDEO by Rudy KouhouptVHS, 3
0.91kg
Hrs., includes materials list and printed plans for a
2lbs
steam engine. Video takes you through every setup from
start to finish.
£70.50
5329
SHOP SECRETS—USING MEASURING TOOLS by
0.45kg
Mike RehmusVHS, 2 hrs., tells you how each measuring 1lbs
tool used in machining is used and cared for. Very
professionally produced. Includes promo for NAMES show
too
£40.50
5330
SAFETY GLASSESA MUST in every shop. Get them
from us or get them from someone else, but don't cut
metal without them! These are good quality and
comfortable.
5401
5411 (metric)
DELUXE XY BASE (Inch) w/ 12″ Base and Adjustable 8.64kg £408.25
HandwheelsAdd a 3480 vertical milling column and the 19lbs
motor/speed control from your lathe and you have a
complete deluxe model 5400 mill.
5401-CNC
5411-CNC
(metric)
DELUXE XY BASE CNC READY w/ 2 stepper motor 9.55kg £519.25
mountsStepper motors and CNC controls not included. 21lbs
5420
5430 (metric)
DELUXE XYZ BASE (Inch) w/ 12″ Base and
Adjustable HandwheelsAdd the motor/speed control
from your lathe and you have a complete deluxe model
5400 mill.
5420-CNC
5430-CNC
(metric)
DELUXE XYZ BASE CNC READY (Inch) w/ 3 stepper 12.73kg £756.00
motor mountsStepper motors and CNC controls not
28lbs
included.
Millhill Supplies Ltd.
- 12 / 17 -
0.11kg
0.25lbs
£7.75
12.27kg £550.50
27lbs
14.02.2017
13
5600
5610 (metric)
Model 2000 8-DIRECTION MILL XY BASEAdd a multi- 10kg
direction vertical milling column and the motor/speed
22lbs
control from your lathe and you have a complete model
2000 mill.
5625
Model 2000 8-DIRECTION MILL XYZ BASEAdd the
5630 (metric) motor/speed control from your lathe and you have a
complete model 2000 mill.
5650
5660 (metric)
£428.50
15.45kg £756.00
34lbs
8-DIRECTION UPGRADE for all existing SHERLINE
4.09kg £267.25
MILLSA multi-direction milling column and an offset base 9lbs
brings your existing mill up to the capabilities of a model
2000 mill.
5680
8-DIRECTION UPGRADE for LATHE VERTICAL
5685 (metric) MILLING COLUMNTurns your lathe/vertical milling
column combination into an 8-direction mill.
4.09kg £267.25
9lbs
6079
1/4″ END MILL HOLDERHolds end mills in 3080 set
0.23kg
0.5lbs
£30.25
6080
3/16″ END MILL HOLDER
0.23kg
0.5lbs
£30.25
6081
1/8″ END MILL HOLDER
0.23kg
0.5lbs
£30.25
6100
HORIZONTAL MILLING CONVERSION
5kg
11lbs
6101
COLUMN CONVERSIONTo optimize the horizontal
3.64kg
conversion, P/N 6100, the mill column should be
8lbs
reworked to allow for the best set up. Contact SHERLINE
for information.
6700
CNC UPGRADE KIT, 5000 OR 5400 MILLReplaces
6710 (metric) the handwheels with stepper motor mounts, ready for
the installation of your own stepper motors and CNC
control.
£131.00
£CALL
1.14kg £252.00
2.5lbs
6705
6715 (metric)
CNC UPGRADE KIT, 2000 MILLReplaces the
1.14kg £270.00
handwheels with stepper motor mounts, ready for the
2.5lbs
installation of your own stepper motors and CNC control.
67127
STEPPER MOTOR2 amp, #23 Frame, dual shaft, 6wire, 136 oz-in stall torque, pre-wired with plug for use
with Sherline rotary or linear controller, flats premachined for Sherline coupler and handwheel set
screws.
0.45kg
1lbs
£75.50
67130
STEPPER MOTOR2 amp, #23 Frame, dual shaft, 6-wire, 0.45kg
136 oz-in stall torque, 6-wire plug-in harness with raw
1lbs
leads for use on applications that do not have the
Sherline 5-pin connector plug, flats pre-machined for
Sherline coupler and handwheel set screws.
£65.50
6720
CNC UPGRADE KIT, 4000 or 4500 LATHEReplaces
6725 (metric) the handwheels with stepper motor mounts, ready for
the installation of your own stepper motors and CNC
control.
6730
6735 (metric)
0.91kg £215.25
2lbs
CNC UPGRADE KIT, 4400 LATHEReplaces the
0.91kg £226.00
handwheels with stepper motor mounts, ready for the
2lbs
installation of your own stepper motors and CNC control.
6740
CNC UPGRADE KIT, 5000 and 5400 Series Mills, Z- 0.68kg £106.00
6745 (metric) axis only
1.5lbs
Millhill Supplies Ltd.
- 13 / 17 -
14.02.2017
14
6750
6755 (metric)
CNC UPGRADE KIT, 2000 Series Mills, Z-axis only
6760
CNC UPGRADE KIT, mill X axis or lathe Crosslide
6765 (metric) only (all models)
6770
6775 (metric)
0.68kg £106.00
1.5lbs
0.45kg
1lbs
£75.50
CNC UPGRADE KIT, mill Y axis only (all mill models) 0.45kg
1lbs
£75.50
6780
CNC UPGRADE KIT, leadscrew axis only,
6785 (metric) 4000/4500-series lathes
0.45kg £140.00
1lbs
6790
6795 (metric)
CNC UPGRADE KIT, leadscrew axis only, 4400series lathes
0.45kg £150.75
1lbs
7506
SET OF MACHINIST’S PARALLELSSets of two
parallel bars in five different sizes sized for miniature
machine tools. Used to support work a known distance
above and parallel to the table.
0.11kg
0.25lbs
£50.50
7550
Super-Lube multi-purpose synthetic grease with
0.11kg
Syncolon® (PTFE), 3 oz tubeTeflon-based grease that 0.25lbs
we use at the factory on all new machines. Clear, nonstaining, heat resistant.
£8.25
7555
Super-Lube dri-film spray lubricant with
Syncolon® (PTFE), 11 oz aerosol canTeflon-based
film that sprays on. Once propellant dries, it leaves a
thin coat of dry lubricant that won't attract chips.
0.45kg
1lbs
£15.00
7600
3/8″ INSERT HOLDER TOOL POSTHas side slot to hold 0.11kg
3/8" shank cutting tool holders plus a 3/8" round hole to 0.25lbs
hold round boring bars.
£20.25
7610
55° NEGATIVE RAKE INSERT HOLDER w/
0.23kg
insertHolds carbide tips for cutting hard materials like 0.5lbs
stainless steel. 5° angle provides negative clearance for
the cutter, which is supported all the way down to the
table for rigidity.
£60.50
7612
REPLACEMENT 4-SIDED CARBIDE INSERT TOOL (for 0.03kg
7610)
0.06lbs
£16.00
7620
SINGLE FLUTE INSERT FLY CUTTERCarbide insert 0.23kg
cuts hard materials. Also is a good compromise between 0.5lbs
a fly cutter and an end mill, because it will cut a 1-1/8"
wide path while still being able to cut right up to a
shoulder.
£60.50
7622
REPLACEMENT 2-SIDED CARBIDE TIP (for 7620)
£16.00
8100
3-AXIS DIGITAL READOUT w/ RPM GAGE FOR
8160 (metric) MILL (inch)Reads table position to .0005", electronic
compensation for backlash
8200
8260 (metric)
1.36kg £378.00
3lbs
2-AXIS DIGITAL READOUT w/ RPM GAGE FOR LATHE 1.36kg £327.50
(inch)Reads table position to .0005", electronic
3lbs
compensation for backlash
8210
3-AXIS DIGITAL READOUT w/ RPM GAGE FOR
8215 (metric) LATHE and VERTICAL MILLING COLUMN
(Inch)Reads table position to .0005", electronic
compensation for backlash
Millhill Supplies Ltd.
0.03kg
0.06lbs
- 14 / 17 -
1.36kg £388.00
3lbs
14.02.2017
15
8220
8225 (metric)
2-AXIS DIGITAL READOUT w/ RPM GAGE FOR LATHE 0.91kg £166.25
without READOUT BOXFor those who already have a
2lbs
Mill DRO package. (Inch) Reads table position to .0005",
electronic compensation for backlash.
8240
Z-AXIS VERTICAL MILLING COLUMN DIGITAL
0.23kg
8245 (metric) READOUT HANDWHEEL PACKAGE (Inch)Adds third 0.5lbs
readout for those who bought 2-axis DRO and later add
a vertical milling column.
£72.75
8700
CNC ROTARY INDEXER w/ CONTROLLERCNC ROTARY 7.73kg £731.00
INDEXER w/ CONTROLLER, STEPPER MOTOR, MOUNT,
17lbs
POWER SUPPLY, CABLES, 4″ ROTARY TABLE AND HOLDDOWNS (Inch)
8710
CNC ROTARY TABLE RISER PLATEOn the 3700-CNC 0.91kg
and 8700 CNC rotary tables, the bottom of the stepper 2lbs
motor mount extends slightly below the bottom surface
of the table. On Sherline mills, the mount overhangs the
side of the table so this is not a problem. On larger mills
or flat table applications a riser plate is needed so that
the stepper motor clears the table surface.
8730
CNC ROTARY TABLE WITH STEPPER MOTORStepper
motor plugs into 4th axis cable of 8760 driver box or
Sherline 8540 or 8020 CNC system to act as 4th axis.
Includes prewired plug.
8760
CNC 4-AXIS DRIVER BOXIncludes 4 cables for X, Y, Z 3.18kg £645.75
and A (Rotary) axes, power supply and parallel cable for 7lbs
attachment to computer's printer port. Linux OS and
EMC 4-axis softare also included on two CD's. Buy or
upgrade a CNC-ready Sherline machine, buy the needed
P/N 67127 stepper motors, plug in and attach to your
computer with Linux/EMC installed and you have the
duplicate of a complete Sherline CNC system. NOTE:
one hour of free technical support provided with
Sherline CNC system is NOT provided when driver box
is purchased separately.
8765
Upgrade any CNC-ready Sherline lathe to CNC
4.09kg £785.75
(Computer not included.)Save compared to complete 9lbs
systems with computer. Includes 2 stepper motors, 4axis 8760 driver box and Linux/EMC software on CD.
Does NOT include software installation and technical
support.
8770
Upgrade any CNC-ready Sherline lathe to CNC
4.55kg £811.50
(Computer not included.)Save compared to complete 10lbs
systems with computer. Includes 2 stepper motors, 4axis 8760 driver box and Linux/EMC software on CD.
Does NOT include software installation and technical
support.
8800
CNC LINEAR CONTROLLER w/ STEPPER MOTOR
2.27kg £484.25
(Inch)Stepper motor bolts onto Sherline CNC-ready
5lbs
stepper motor mounts. Controller drives stepper motor to
move any axis on lathe or mill. From .0005" to 9.9995".
Will work on any lathe or mill axis that already has a
stepper motor mount installed. Includes power supply
and cable. Can be daisy chained with other Sherline
linear or rotary controllers.
Millhill Supplies Ltd.
- 15 / 17 -
£30.25
4.55kg £398.25
10lbs
14.02.2017
16
8850
CNC MILL OR LATHE POWER FEEDReplaces
2.73kg £525.00
handwheel on X- or Y-axis of mill or lathe crosslide with 6lbs
stepper motor mount and stepper motor. Motor is driven
by self-contained computer/keypad unit and power
supply to allow movement from .0005" to 9.9995".
Includes drill block for locating mounting holes. Can be
daisy chained with other Sherline controllers
8860
CNC MILL POWER FEEDReplaces handwheel on Z-axis 3.18kg £514.00
of mill with stepper motor mount and stepper motor.
7lbs
Motor is driven by self-contained computer/keypad unit
and power supply to move Z-axis in programmable
.0005" increments up to full length of travel. Includes
drill block for locating mounting holes. Can be daisy
chained with other Sherline linear or rotary controllers.
8865
CNC MILL POWER FEEDSee description for 8860.
8870
CNC LATHE LEADSCREW POWER FEEDReplaces
3.18kg £559.50
handwheel on long leadscrew of lathe with stepper motor 7lbs
mount and stepper motor. Motor is driven by selfcontained computer/keypad unit and power supply to
move the saddle from .0005 to 9.9995". Includes drill
block for locating mounting holes. Can be daisy chained
with other Sherline linear or rotary controllers.
8880
CNC LATHE LEADSCREW POWER FEEDSee
description for 8870 above.
3.18kg £514.00
7lbs
3.18kg £570.50
7lbs
SHERLINE CHUCKS
Part
Number
Part
Weight
1010
0JT 5/32″ Jacobs drill chuck w/ #1 Morse arbor
(headstock), drawbolt and key
0.23kg
0.5lbs
1012
Sensitive drilling attachmentSee Accessories section
following chuck section.
0.91kg £111.00
2lbs
1015
0JT 5/32″ Jacobs drill chuck w/ #0 Morse (tailstock)
arbor and keySherline Lathe
0.23kg
0.5lbs
1030
4-Jaw Chuck (3.125″ O.D.)
0.91kg £136.00
2lbs
1031
14 x 1 mm 3-jaw chuck (2.5″ O.D.)14 x 1 mm threads
for use on old Sears 6″ lathe
0.91kg £121.00
2lbs
1035
14 x 1 mm 4-jaw chuck (2.5″ O.D.)14 x 1 mm threads
for use on old Sears 6″ lathe
0.91kg £121.00
2lbs
1040
3-Jaw Chuck (3.125″ O.D.)
0.91kg £141.00
2lbs
1041
3-Jaw Chuck (2.5″ O.D.)
0.91kg £101.00
2lbs
1044
4-Jaw Chuck (2.5″ O.D.)
0.91kg £110.75
2lbs
1068
12 x 1 mm 3-jaw chuck (2.5″ O.D.) w/ reversible
jaws12 x1 mm threads for use on Unimat SL 1000
0.91kg £121.00
2lbs
1069
3/8″ Jacobs Tailstock Drill Chuck w/ #0 and #1 Morse 0.68kg
arbors, drawbolt and key
1.5lbs
Millhill Supplies Ltd.
- 16 / 17 -
Cost
£70.50
£70.50
£65.50
14.02.2017
17
1070
1/2-20 3-Jaw (2.5″ O.D.)1/2-20 threads for use on Unimat 0.91kg £121.00
3 or Cowells lathes
2lbs
1071
12 x 1 mm 4-jaw chuck (2.5″ O.D.)12 x1 mm threads for 0.91kg £121.00
use on Unimat SL 1000
2lbs
1072
1/4″ Jacobs tailstock drill chuck w/ #0 and #1 Morse
arbors, drawbolt and key
1073
1/2-20 4-Jaw Chuck (2.5″ O.D.)1/2-20 threads for use on 0.91kg £121.00
Unimat 3 or Cowells lathes
2lbs
1075
Self-centering 4-Jaw Chuck (2.5″ O.D.)
0.91kg £131.00
2lbs
1076
Self-centering 4-Jaw Chuck (3.125″ O.D.)
0.91kg £166.25
2lbs
3072
1/4″ Jacobs Drill Chuck w/ #1 Morse arbor, drawbolt 0.23kg
and key#0 Morse arbor not incl. See P/N 1072 if you need 0.5lbs
both arbors
£50.50
3073
3/8″ Jacobs Drill Chuck w/ #1 Morse arbor, drawbolt 0.34kg
and key#0 Morse arbor not incl. See P/N 1069 if you need 0.75lbs
both arbors
£60.50
Millhill Supplies Ltd.
- 17 / 17 -
0.23kg
0.5lbs
£55.50
14.02.2017
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising