MP34DT01-M
MP34DT01-M
MEMS audio sensor omnidirectional digital microphone
Datasheet - production data
 VoIP
 Speech recognition
 A/V eLearning devices
 Gaming and virtual reality input devices
 Digital still and video cameras
 Antitheft systems
Description
The MP34DT01-M is an ultra-compact, lowpower, omnidirectional, digital MEMS microphone
built with a capacitive sensing element and an IC
interface.
HCLGA (3 x 4 x 1.06 4LD)
Features
The sensing element, capable of detecting
acoustic waves, is manufactured using a
specialized silicon micromachining process
dedicated to produce audio sensors.
 Single supply voltage
 Low power consumption
 120 dBSPL acoustic overload point
The IC interface is manufactured using a CMOS
process that allows designing a dedicated circuit
able to provide a digital signal externally in PDM
format.
 61 dB signal-to-noise ratio
 Omnidirectional sensitivity
 – 26 dBFS sensitivity
 PDM output
 HCLGA package
– Top-port design
– SMD-compliant
– EMI-shielded
– ECOPACK®, RoHS, and “Green” compliant
The MP34DT01-M has an acoustic overload point
of 120 dBSPL with a 61 dB signal-to-noise ratio
and –26 dBFS sensitivity.
The MP34DT01-M is available in a top-port, SMDcompliant, EMI-shielded package and is
guaranteed to operate over an extended
temperature range from -40 °C to +85 °C.
Applications
 Mobile terminals
 Laptop and notebook computers
 Portable media players
Table 1. Device summary
order codes
Temperature range [°C]
Package
-40 to +85
HCLGA (3 x 4 x 1.06) mm 4LD
MP34DT01-M
Packing
Tray
MP34DT01TR-M
June 2014
This is information on a product in full production.
Tape and reel
DocID026514 Rev 1
1/14
www.st.com
Contents
MP34DT01-M
Contents
1
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Acoustic and electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1
Acoustic and electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2
Frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3
Timing characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3
Sensing element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5
Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.1
L/R channel selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7
Carrier tape mechanical specifications . . . . . . . . . . . . . . . . . . . . . . . . . 12
8
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2/14
DocID026514 Rev 1
MP34DT01-M
1
Pin description
Pin description
Figure 1. Pin connections
*$066*
/5
&/.
9GG
'287
*1'
%277209,(:
Table 2. Pin description
Pin #
Pin name
Function
1
Vdd
Power supply
2
LR
Left/Right channel selection
3
CLK
Synchronization input clock
4
DOUT
Left/Right PDM data output
5 (ground ring)
GND
0 V supply
DocID026514 Rev 1
3/14
14
Acoustic and electrical specifications
MP34DT01-M
2
Acoustic and electrical specifications
2.1
Acoustic and electrical characteristics
The values listed in the table below are specified for Vdd = 1.8 V, Clock = 2.4 MHz,
T = 25 °C, unless otherwise noted.
Table 3. Acoustic and electrical characteristics
Symbol
Parameter
Test condition
Vdd
Supply voltage
Idd
Current consumption in
normal mode
IddPdn
Current consumption in
power-down mode (2)
Scc
Short-circuit current
AOP
Acoustic overload point
So
Typ. (1)
Max.
Unit
1.64
1.8
3.6
V
Mean value
0.6
mA
20
µA
1
10
120
Sensitivity
-23
-26
mA
dBSPL
-29
dBFS
SNR
Signal-to-noise ratio
A-weighted at 1 kHz,
1 Pa
61
dB
PSR
Power supply rejection
Guaranteed by
design
-70
dBFS
Clock
Input clock frequency (3)
1
3.25
MHz
10
ms
-40
+85
°C
Guaranteed by
design
2.4
Ton
Turn-on time (4)
Top
Operating temperature
range
VIOL
Low level logic
input/output voltage
Iout = 1 mA
-0.3
0.35xVdd
V
VIOH
High level logic
input/output voltage
Iout = 1 mA
0.65xVdd
Vdd+0.3
V
1. Typical specifications are not guaranteed.
2. Input clock in static mode.
3. Duty cycle: min = 40% max = 60%.
4. Time from the first clock edge to valid output data.
4/14
Min.
DocID026514 Rev 1
MP34DT01-M
2.2
Acoustic and electrical specifications
Frequency response
Figure 2. Typical frequency response normalized at 1 kHz
DocID026514 Rev 1
5/14
14
Acoustic and electrical specifications
2.3
MP34DT01-M
Timing characteristics
Table 4. Timing characteristics
Parameter
Description
fCLK
Clock frequency for normal mode
fPD
Clock frequency for power-down mode
TCLK
Clock period for normal mode
Data enabled on DATA line, L/R pin = 1
TR,DIS
Data disabled on DATA line, L/R pin = 1
TL,DIS
Max.
Unit
1
3.25
MHz
0.23
MHz
1000
ns
308
TR,EN
TL,EN
Min.
(1)
18
ns
16(1)
(1)
Data enabled on DATA line, L/R pin = 0
18
ns
ns
16(1)
Data disabled on DATA line, L/R pin = 0
ns
1. From design simulations
Figure 3. Timing waveforms
TCLK
CLK
TL,DIS
TR,EN
TR,DIS
High Z
PDM R
High Z
TL,EN
PDM L
High Z
High Z
AM045165v1
6/14
DocID026514 Rev 1
MP34DT01-M
3
Sensing element
Sensing element
The sensing element shall mean the acoustic sensor consisting of a conductive movable
plate and a fixed plate placed in a tiny silicon chip. This sensor transducers the sound
pressure into the changes of coupled capacity between those two plates.
Omron Corporation supplies this element for STMicroelectronics.
DocID026514 Rev 1
7/14
14
Absolute maximum ratings
4
MP34DT01-M
Absolute maximum ratings
Stresses above those listed as “absolute maximum ratings” may cause permanent damage
to the device. This is a stress rating only and functional operation of the device under these
conditions is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
Table 5. Absolute maximum ratings
Symbol
Ratings
Vdd
Supply voltage
Vin
Input voltage on any control pin
TSTG
Storage temperature range
ESD
Electrostatic discharge protection
Maximum value
Unit
-0.3 to 6
V
-0.3 to Vdd +0.3
V
-40 to +125
°C
2 (HBM)
kV
This device is sensitive to mechanical shock, improper handling can cause
permanent damage to the part.
This device is ESD-sensitive, improper handling can cause permanent damage to the
part.
8/14
DocID026514 Rev 1
MP34DT01-M
Functionality
5
Functionality
5.1
L/R channel selection
The L/R digital pad lets the user select the DOUT signal pattern as shown in Table 6. The
L/R pin must be connected to Vdd or GND.
Table 6. L/R channel selection
L/R
CLK low
CLK high
GND
Data valid
High impedance
Vdd
High impedance
Data valid
DocID026514 Rev 1
9/14
14
Package mechanical data
6
MP34DT01-M
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
Soldering information
The HCLGA 3x4 4LD package is also compliant with the RoHS and “Green” standards and
is qualified for soldering heat resistance according to JEDEC J-STD-020.
Landing pattern and soldering recommendations are available at www.st.com.
Figure 4. Recommended soldering profile limits
tp
TP
CRITICAL ZONE
RAMP-UP
TL to T P
TL
TEMPERATURE
TSMAX
tL
TSMIN
ts
PREHEAT
RAMP-DOWN
T25°C to PEAK
30
60
90
120
150
180
TIME
210
240
270
300
330
360
390
AM045166v1
Table 7. Recommended soldering profile limits
Description
Average ramp rate
Parameter
Pb free
TL to TP
3 °C/sec max
TSMIN
TSMAX
tS
150 °C
200 °C
60 sec to 120 sec
Preheat
Minimum temperature
Maximum temperature
Time (TSMIN to TSMAX)
TSMAX to TL
Ramp-up rate
Time maintained above liquidus temperature
Liquidus temperature
tL
TL
60 sec to 150 sec
217 °C
Peak temperature
TP
260 °C max
Time within 5 °C of actual peak temperature
10/14
20 sec to 40 sec
Ramp-down rate
6 °C/sec max
Time 25 °C (t25 °C) to peak temperature
8 minutes max
DocID026514 Rev 1
MP34DT01-M
Package mechanical data
Figure 5. HCLGA (3 x 4 x 1.06 mm) 4-lead package outline
32$BB$
Note:
The MEMS microphone metal cap can exhibit some level of variation in color when the
device is subjected to thermal process.
Dimensions are in millimeter unless otherwise specified. General tolerance is  0.15 mm
unless otherwise specified.
Table 8. HCLGA (3 x 4 x 1.06 mm) mechanical data
Item
Dimension (mm)
Tolerance (mm)
Length [L]
4
± 0.1
Width [W]
3
± 0.1
Height [H]
1.06
± 0.1
DocID026514 Rev 1
11/14
14
Carrier tape mechanical specifications
7
MP34DT01-M
Carrier tape mechanical specifications
Figure 6. Carrier tape without microphone-top view
Figure 7. Carrier tape with microphone-top view
12/14
DocID026514 Rev 1
MP34DT01-M
8
Revision history
Revision history
Table 9. Document revision history
Date
Revision
19-Jun-2014
1
Changes
Initial release
DocID026514 Rev 1
13/14
14
MP34DT01-M
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2014 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
14/14
DocID026514 Rev 1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement