Gobo Flower

Gobo Flower
.
TABLE OF CONTENTS
1. Introduction
2. Safety Instruction
3. Description
4. Operation and Technical Specification
5. Lamp installation or replacement
6. Beam Angle
7. Troubleshooting
8.
Gobo Flower
User Guide
Professional Entertainment Technology
Fixture Cleaning
Широкий ассортимент оборудования ACME
на www.maxlight.ru
1. Introduction
♦
Don’t connect the device to any dimmer pack or power pack.
♦
Do not touch any wire during operation as high voltage might be causing electric
shock.
Thank you for purchasing Wild Tech’s Gobo Flower. With 12 gobos/ colors, precise optics,
and 250W powerful output, the Gobo Flower
is perfect for discos, clubs, bars, and parties.
.
Warning
2. Safety Instruction
♦
about the installation, usage and maintenance.
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
Please read carefully the instruction, which includes important information
♦
Never touch bulb with bare fingers as it is very hot after using.
WARNING
♦
Hot lamp explosion hazard. Do not open the unit within five minutes after switching off.
♦
Please keep this User Guide for future consultation. If you sell the unit to another user,
♦
Do not start on the unit without bulb enclosure or housing are damaged.
be sure that they also receive this instruction booklet.
♦
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
♦
Unpack and check carefully there is no transportation damage before using the unit.
♦
Before operating, ensure that the voltage and frequency of power supply match the
damaged.
♦
Do not look directly at the light while the bulb is on.
power requirements of the unit.
♦
It’s important to ground the yellow/green conductor to earth in order to avoid electric
Caution
shock.
There are no user serviceable parts inside the unit. Do not open the housing or attempt
♦
The unit is for indoor use only. Use only in a dry location.
any repairs yourself. In the unlikely event your unit may require service, please contact
♦
The unit must be installed in a location with adequate ventilation, at least 50cm from
your nearest dealer.
adjacent surfaces. Be sure that no ventilation slots are blocked.
Rigging the fixtures
♦
Disconnect mains power before fuse/lamp replacement or servicing.
♦
Replace fuse/lamp only with the same type.
The unit should be mounted via its screw holes on the bracket. Always ensure that the
♦
Make sure there is no flammable materials close to the unit while operating as it is fire
unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the
hazard.
structure to which you are attaching the unit is secure and is able to support a weight of
♦
Use safety cable when fixes this unit.
10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the
♦
Maximum ambient temperature is TA: 40℃. Don’t operate it where the temperature is
weight of the unit when installing the fixture.
higher than this.
The installation must be carried out by qualified service people only. The device should
Unit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand
be installed out of reach of people and outside areas where persons may walk by or be
during its operation. Turn off the power and allow about 15 minutes for the unit to cool
seated.
♦
down before replacing bulb or serving.
♦
In the event of serious operating problem, stop using the unit immediately. Never try to
repair the unit by yourself. Repairs carried out by unskilled people can lead to damage
or malfunction. Please contact the nearest authorized technical assistance center.
Always use the same type spare parts.
3. Description
5. Lamp installation or replacement
• Always switch off the mains supply and never handle the lamp or luminaire when it is hot.
• Do not touch the bulb with bare hands. If this does happen, clean the lamp with denatured
alcohol and wipe with a lint free cloth before installing.
Pull the socket off the lamp.
Do not pull the wires.
1. Optical lens with manual focus adjustment.
2. Hanging bracket with 2 knobs on both sides to fasten the unit and a mounting hole to fix a
mounting hook.
3. Mains input with IEC socket and integrated fuse holder, connect the supplied mains cable
here.
6. Beam angle
4. Lamp compartment, to be opened with this screw.
5. Internal microphone
6. ј” jack used to connect t he optional CA-8 controller.
7. Cooling fan
4. Operation and Technical Specification
• Plugging into the mains power, the fixture starts running. The Gobo Flower runs in
automatic or sound activated mode.
• Fan cooled and thermal switch for overheat protection.
The Projector is best to be placed 5 meters from wall, and from this distance the light effect
Specification:
will cover an area of 4 m x 4 m.
• Voltage: AC 120V~60Hz 230V/240V/250V~50Hz/60Hz
• Fuse: 20mm glass 250V T6.3A / 20mm glass 250V T5A
• Bulb: ELC 24V 250W
• Dimension: 306 x 263 x 140 mm
• Weight: 7.2 kgs
8. Fixture Cleaning
7. Troubleshooting
The cleaning of internal and external optical lenses and/or mirrors must be carried out
Problem
Probable cause(s)
Suggested remedy
No light
No power to the fixture
Check power connections
which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater
Blown fuse
If power is applied but does not
accumulation of dirt on the unit’s optics.
light, please check and replace
y
Clean with soft cloth using normal glass cleaning fluid.
fuse if necessary.
y
Always dry the parts carefully.
periodically to optimize light output. Cleaning frequency depends on the environment in
y
Clean the external optics at least every 20 days. Clean the internal optics at least
Burned out lamp
Install new lamp.
Fixture too hot
Allow to cool down. Improve air
every 30/60 days.
flow around the unit.
No action
Sound too low to activate
EC Declaration of Conformity
Increase volume.
control circuit
Electrical malfunction
Refer to service technician.
We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55014-2: 1997 A1:2001, EN61000-4-2: 1995; EN61000-4-3:2002;
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6:1996,
EN61000-4-11: 1994.
&
Harmonized Standard
EN60598-1: 2000+ALL:2000+A12:2002
Safety of household and similar electrical appliances
Part 1 : General requirements
Innovation , Quality , Performance
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement