EdgeStar CWB1760FD
Built-in Wine and Beverage Cooler
CWB1760FD
Owner’s Manual
For more information on other great EdgeStar products on the web, go to http://www.edgestar.com
Important Safety Information
Improper handling can cause serious damage to the EdgeStar wine and beverage cooler and/or injury to the user. This
wine and beverage cooler is designed for domestic indoor use only. Do not use the unit for industrial or commercial
use. Any other use may invalidate the warranty. Please review the ratings label located on the rear panel of the unit for
electrical and other technical data related to this unit. The unit must be used in a properly grounded wall outlet.
Please read and follow the safety information listed below to reduce the risk of fire, electric shock or injury.
Electrical Safety
 Do not exceed the power outlet ratings.
 It is recommended that the wine and beverage
cooler be connected on its own circuit.
 This unit must be installed in accordance with
state and local electrical codes.
 A standard electrical supply (115 V, 60Hz), that is
properly grounded in accordance with the
National Electrical Code and local codes and
ordinances is required.
 Use outlets that cannot be turned off by a switch
or pull chain.
 Always turn the unit off and unplug it from the
outlet when cleaning.
 Unplug the unit if it is not going to be used for an
extended period of time.
 Do not operate the unit with a power plug missing
the ground plug, a damaged cord or a loose
socket.
 Be sure the wine and beverage cooler is properly
grounded.
 Never plug or unplug the unit with wet hands.
 Do not bypass, cut or remove the grounding plug.
 Do not use extension cords or power strips with
this unit. You may need to contact your electrician
if it is necessary to use a longer cord or if you do
not have a grounded outlet. Do not modify the
power cord’s length or share the outlet with other
appliances.
 Do not start or stop the unit by switching the
circuit’s power on and off.
 If the power cord is damaged, it must be replaced
by the manufacturer or a qualified technician.
 Never repair the unit while it is plugged in.
 Immediately unplug the unit if it makes strange
sounds, emits smells or smoke comes out of it,
and contact customer service.
 Do not remove any part of the casing unless
instructed by an authorized technician.
 You should never attempt to repair the unit
yourself.
 Contact customer service for service options if the
unit needs service.
i
General Safety
 To prevent back and other types of injuries, use at
least two people to move and install the unit.
 This appliance is not intended for use by persons,
including children, with reduced physical, sensory or
mental capabilities, unless they have been given
supervision or instruction concerning the use of the
appliance by the person(s) responsible for their
safety.
 Install the wine and beverage cooler in a wellventilated area where the ambient temperature is
above 65°F and below 90°F.
 The temperature range for this cooler is optimized
for wine and beverage storage. Perishable food
items may require a different storage environment.
 Do not place hot or warm items into the cooler
before they cool down to room temperature.
 This unit is designed to be installed indoors, and
protected from rain, sleet, snow, and/or moisture.
 This unit is not intended to be used by children.
 Children should be supervised to ensure that they
do not play with this product.
 Never allow children to crawl inside the unit. If
disposing the unit, remove the door.
 Do not use this appliance near flammable gas or
combustibles, such as gasoline, benzene, thinner,
etc.
 Do not place the unit near heat sources such as
ovens, grills, or direct sunlight.
 Only use in an upright position on a flat, level
surface and provide proper ventilation.
 Do not pinch or kink the power supply line between
the unit and cabinet.
 Do not leave any cleaning solutions in the unit
 Do not use solvent-based cleaning agents or
abrasive solutions to clean the unit as they may
damage the interior and exterior.
 Do not place any other appliances on top of the unit.
 Do not turn the unit upside down, on its side, or at
an angle off level.
 Take care to keep the keys to the unit’s lock away
from children.
 Do not move the unit without emptying the contents
and securing the door in a closed position.
Important Safety Information (Continued)
R600a
This appliance is CFC- and HFC-free and contains small quantities of Isobutane (R600a), which is
environmentally friendly, but flammable. It does not damage the ozone layer, nor does it contribute to
greenhouse gases. Care must be taken during transportation and set up of the appliance. Make sure
to check that no parts of the cooling system are damaged. Leaking coolant can ignite and may cause
personal injury.
In the event of any damage:







Avoid open flames and anything that may create a spark.
Disconnect from the main power supply.
Vent the room in which the appliance is located for several minutes.
Contact the EdgeStar Customer Service Department for advice.
The more coolant there is in an appliance, the larger the room it should be installed in. In the
event of a leak, if the appliance is in a small room, there is the danger of combustible gases
building up. For every ounce of coolant at least 325 cubic feet of room space is required. The
amount of coolant in the appliance is stated on the rating label in the lower left side of the
inner cabinet of the appliance. It is hazardous for anyone other than an Authorized Service
Person to carry out servicing or repairs to this appliance.
Take serious care when handling, moving and using the appliance to avoid either damaging
the refrigerant tubing, or increasing the risk of a leak.
Replacing component parts and servicing must be done by manufacturer authorized service
personnel, so as to minimize the risk of possible ignition due to incorrect parts or improper
service.
Risk of child entrapment!
Before discarding your old appliance:


Take off the door(s).
Leave the shelves in place so that children cannot easily crawl into the unit.
- SAVE THESE INSTRUCTIONS -
EdgeStar Wine and Beverage Cooler
ii
Table of Contents
IMPORTANT SAFETY INFORMATION ................................................................. I
IMPORTANT SAFETY INFORMATION (CONTINUED) ....................................... II
INTRODUCTION ................................................................................................... 1
PARTS IDENTIFICATION ..................................................................................... 2
FRONT VIEW ........................................................................................................ 2
INSTALLING THE WINE AND BEVERAGE COOLER ........................................ 3
TYPES OF INSTALLATION....................................................................................... 3
Free Standing Installation: ............................................................................ 3
Built-in Installation: ........................................................................................ 3
INSTALLATION CLEARANCE REQUIREMENTS .......................................................... 4
ELECTRICAL REQUIREMENTS ................................................................................ 5
Recommended grounding method ................................................................ 5
LEVELING THE W INE AND BEVERAGE COOLER ....................................................... 5
INSTALLING AND REMOVING THE SHELVES ............................................................ 6
INSTALLING THE HANDLES .................................................................................... 7
OPERATION .......................................................................................................... 8
USING THE TEMPERATURE CONTROL PANEL ......................................................... 8
NORMAL SOUNDS .............................................................................................. 10
DEFROSTING ..................................................................................................... 10
PREPARING THE W INE AND BEVERAGE COOLER FOR STORAGE............................ 10
CLEANING AND MAINTENANCE ...................................................................... 11
EXTERIOR CLEANING ......................................................................................... 11
INTERIOR CLEANING ........................................................................................... 11
TROUBLESHOOTING ........................................................................................ 11
TROUBLESHOOTING CONTINUED ......................................................................... 12
SPECIFICATIONS ............................................................................................... 13
First Time Operating Instructions
Before use, make sure all packaging labels and materials are all removed from
the unit. Be sure to keep track of all included parts and pieces before discarding
packaging materials. It is advised that you keep the original box and packaging
materials in case you are ever to move or ship the appliance in the future.
Let the unit stand for at least 24 hours before you use it; this allows the cooling
components time to settle from transit. The instruction manual should be read
before use.
This owner’s manual is provided for reference use only. Specifications may
change without prior notice. Refer to the product label on the interior left
cabinet wall of your wine and beverage cooler for the latest technical
information.
iii
Introduction
Thank you for purchasing this EdgeStar wine and beverage cooler. We are glad
you chose us. We believe that your purchase of this product opens a relationship
between you and EdgeStar. We will provide the customer support needed to
nurture that relationship.
This manual contains important information regarding the proper installation, use
and maintenance of your wine and beverage cooler. Following this manual will
ensure that your product will work at its peak performance and efficiency.
Please save the original product packaging in case you need to safely transport
your wine and beverage cooler.
For Your Records:
Please write down the model number and serial number
below for future reference. Both numbers are located on the
rating label on the interior left cabinet wall of your unit and are
needed to obtain warranty service. You may also want to
staple your receipt to this manual as it is the proof of your
purchase, and is also needed for service under your
warranty.
Model Number:
Serial Number:
Date of Purchase:
To better serve you, please do the following before contacting customer service:
1

If you received a damaged product, immediately contact the retailer or
dealer that sold you the product.

Read and follow this instruction manual carefully to help you install, use
and maintain your wine and beverage cooler.

Read the troubleshooting section of this manual as it will help you
diagnose and solve common issues.

Visit us on the web at http://www.edgestar.com to register your
product, download product guides, additional troubleshooting resources
and up-to-date information.

If you need warranty service, our friendly customer service
representatives are available via email at [email protected] or by
telephone at 1 (866) 319-5473.
Parts Identification
Tip: Gather the model
and serial number
from the product label
and write them down
before installing the
wine and beverage
cooler.
Front View
Control Panel
Shelf
Handle
Lock
Kick Plate
Leveling Leg
EdgeStar Wine and Beverage Cooler
2
Installing the Wine and Beverage Cooler
The wine and beverage cooler should be installed in accordance with
local electrical code requirements. The wine and beverage cooler should
also be placed in a location that is strong enough to support its total
weight, keeping in mind that it will weigh substantially more when fully
loaded than when empty.
Before you plug the wine and beverage cooler into a power supply, be
sure to let it stand upright for at least 24 hours to allow the compressor’s
oils to settle.
Unpacking the Wine and Beverage Cooler
WARNING: Use two or more people to move and install the wine and
beverage cooler. Failure to do so can result in back or other injury.
Carefully remove the packaging materials. Remove any shipping tape
and glue from your wine and beverage cooler before using. Do not use
sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners
to remove tape or glue. These products can damage the surface of your
wine and beverage cooler.
IMPORTANT: Do not remove any safety, warning, or product information
labels from your wine and beverage cooler.
Types of Installation
This wine and beverage cooler has been designed for free standing or
built-in installation. In every case, there must be adequate ventilation and
access for service.
Free Standing Installation:
A free standing installation will allow you to install the wine and beverage
cooler in almost any location you desire. You must follow the stated
instructions for electrical requirements and leveling the wine and
beverage cooler.
Built-in Installation:
A recessed installation will allow you to install the wine and beverage
cooler under a counter or in a kitchen cabinet provided the required
clearance space around the wine and beverage cooler is followed.
It is necessary to allow adequate ventilation space around the unit (make
sure there is at least some ventilation room for the back of the unit). The
following additional items must be observed.
1. Place the wine and beverage cooler in front of the installation location.
Adjust the feet and place the unit flat on the floor or on a platform
depending on your installation requirements.
2. If the electrical outlet for the wine and beverage cooler is behind the
cabinet, plug in the wine and beverage cooler.
3. Push the wine and beverage cooler into position.
WARNING: Do NOT install the wine and beverage cooler behind a closed
cabinet door.
3
Installation Clearance Requirements
When installing the wine and beverage cooler under a counter, follow the
recommended spacing dimensions shown.
• To ensure proper service access and ventilation, allow at least 2-3” of
clearance at the back of the unit. The installation should allow the unit to
be pulled forward for servicing, if necessary.
Important Notes:
Side View
• Choose a location that has
ambient temperatures above
65°F and below 90°F.
Operation outside of these
temperatures may result in
lowered efficiency or cause
other adverse effects.
• This unit MUST be installed
in an area protected from the
elements, e.g., wind, rain,
water spray or drips.
• The wine and beverage
cooler should not be located
next to ovens, grills or other
high heat sources.
• Do not kink or pinch the
power supply cord between
the cooler and wall or cabinet.
• The wine and beverage cooler should be installed on a firm and level
surface that will be able to support the entire weight of a fully loaded unit.
It is important for the wine and beverage cooler to be level in order to
work properly. If needed, you can adjust the height of the wine and
beverage cooler by rotating the feet. See the “Leveling the Wine and
beverage cooler” section.
• A standard electrical supply (115 VAC only, 60 Hz), properly grounded
in accordance with National Electrical Code and local codes and
ordinances is required.
EdgeStar Wine and Beverage Cooler
4
Electrical Requirements





ELECTRIC SHOCK HAZARD!
Plug into a grounded 3-prong outlet.
Never remove the grounding prong from the plug.
Never use an adapter to bypass the grounding prong.
DO NOT use an extension cord.
Failure to follow these instructions can result in fire,
electrical shock, or death.
Before you move your wine and beverage cooler into its final location, it is
important to make sure you have the proper electrical connection:
A standard electrical supply (115 V, 60Hz), properly grounded in
accordance with the National Electrical Code and local codes and
ordinances, is required.
It is recommended that a separate circuit, serving only your wine and
beverage cooler, be provided. Use receptacles that cannot be turned off
by a switch or pull chain.
The fuse (or circuit breaker) size should be 3 Amps.
Recommended grounding method
For your personal safety, this appliance must be grounded. It is equipped
with a power supply cord having a 3-prong grounding plug. To minimize
possible shock hazard, the cord must be plugged into a mating 3-pronged
wall socket, and grounded in accordance with the National Electrical
Code and local codes and ordinances. If a mating wall socket is not
available, it is the personal responsibility of the customer to have a
properly grounded, 3-prong wall receptacle installed by a qualified
electrician.
Leveling the Wine and Beverage Cooler
It is important for the wine and beverage cooler to be leveled in order to
work properly. It can be rsaised or lowered by rotating the plastic sheaths
around each of the front two feet on the bottom of the machine. If you find
that the surface is not level, rotate the feet until the wine and beverage
cooler becomes level .You may need to make several adjustments to
level it. We recommend using a carpenter’s level to check the machine.
1. Place a carpenter’s level on top of the product to see if the wine and
beverage cooler is level from front to back and side to side.
2. Adjust the height of the feet as follows:
Turn the leveling feet clockwise to lower that side of the cooler.
Turn the leveling feet counterclockwise to raise that side of the wine and
beverage cooler.
IMPORTANT: Once you are ready to install it in a cabinet or directly on
the floor, you must adjust the front feet to level the wine and beverage
cooler.
5
Installing and Removing the Shelves
To prevent damaging the door gasket, make sure to open the door all the
way before pulling the shelves out of their track.
To install the shelves:
1. Open the door(s) completely.
2. Slide the shelf on the shelf track and slowly push back until it stops.
3. Push down on the front of the shelf to allow the back of the shelf to lift
over the plastic post. (Imagine a seesaw movement.) Continue to push
the shelf back until both notches pass through the plastic posts on each
side of the shelf track.
4. Continue to push the shelf back.
To remove the shelves:
1. Open the door completely.
2. If necessary, make sure you remove all the contents sitting on the
shelf.
3. Pull the shelf forward until the notch aligns with the plastic post on each
side of the shelf track.
4. Lift the shelf until both notches pass through the posts.
5. Continue to pull the shelf forward until it is completely removed from
the inner compartment.
EdgeStar Wine and Beverage Cooler
6
Installing the Handles
To install the shelves:
1. Remove the door gasket (1) on the side you wish to install the handle.
You can see two designated holes for handle installation.
2. Install the handle (4) tightly as shown above with two screws (3) and
flat washers (2) provided.
3. Replace the door gasket.
7
OPERATION
Using the Temperature Control Panel
Right Zone
Left Zone
Each zone is independently controlled by the touchpad controls that are
located in the interior of the right cabinet zone (pictured above). The
temperature display can be in Fahrenheit or Celsius. The right zone of
this wine and beverage cooler has a temperature range from 41°F to
72°F. The left zone has a temperature range from 36°F to 43°F.
Note: Whether your wine
and beverage cooler can
reach the actual set
temperature(s) depends on
the ambient environmental
conditions.
To toggle between Fahrenheit and Celsius, press and hold the
button for five (5) seconds.
The digital display above the
symbol shows the set temperature in
the left [beverage] zone. The digital display above the
the set temperature in the right [wine] zone.
Press the
symbol shows
button on the control panel to adjust the set
temperature higher and the
button to lower the set temperature.
These buttons will scroll the temperature by one (1) degree increments.
Once you see the desired temperature, stop pressing the button(s).
Note: Allow at least 24 hours before storing your wines and beverages to
allow the temperature to acclimate.
Caution: If you powered off
the unit, please wait at least
5 minutes before powering it
back on.
Each zone also features a white LED light. Press the
button to
turn the inner lights on, and press it again to turn the lights off. By default,
the lights will turn on when you open one of the doors.
Press and hold the power button
for approximately five (5)
seconds to turn the unit’s power on or off.
EdgeStar Wine and Beverage Cooler
8
Allow at least 24 hours
before storing your
beverages to allow the
temperature to acclimate.
Advanced Functions
This unit is equipped with a temperature alarm. The alarm will sound and
the temperature display will flash under the following conditions:
- The door has been left open for more than 60 seconds.
- There has been a lengthy interruption to the power supply.
- The ventilation opening is covered or there is a large build-up of
debris.
Simply pressing the power button once will disable the alarm.
Sabbath Mode
This unit is equipped with Sabbath mode for the observance of religious
holidays. This mode turns off the display, interior light and the alarm.
To enable Sabbath mode, press and hold the
and
buttons for five (5) seconds. The indicator light will flash four (4) times,
confirming that the unit is now in Sabbath mode. The unit will exit
Sabbath mode automatically after 96 hours or the user can once again
press and hold the
and
buttons for five (5) seconds.
Silent Mode
By default, this wine and beverage cooler is in Silent Mode, which is very
energy efficient and minimizes the unit’s noise output. In this mode, the
internal fans are turned off. If you plan to store wine long-term, it is
imperative that the temperature and humidity inside the wine zone stay
consistent. To accomplish this, this unit is also programmed with a
Dynamic Mode option. In Dynamic Mode, the unit uses powerful fan
forced air circulation for even cooling. Press and hold the
for
approximately five (5) seconds to enter Dynamic Mode. The unit will beep
five (5) times to confirm it is in Dynamic Mode. To change back to Silent
Mode, press and hold the
key for five (5) seconds. The unit will
beep three (3) times to confirm it is back in Silent Mode.
9
Normal Sounds
Your new wine and beverage cooler may make sounds that are not
familiar to you. Most of the new sounds are normal. Hard surfaces like the
floor and walls can make the sounds seem louder than they actually are.
The following describes the kinds of sounds that might be new to you and
what may be making them.
 Rattling noises may come from the flow of the refrigerant. Items
stored on top of the wine and beverage cooler can also make noises.
 The high efficiency compressor may make a pulsating or high-pitched
sound.
 As each cycle ends, you may hear a gurgling sound due to the
refrigerant flowing in your wine and beverage cooler.
 You may hear air being forced over the condenser by the condenser
fan.
Defrosting
Note that under most refrigerating settings, the unit will automatically
defrost under most ambient conditions. However, on colder settings,
some frost may build up. Additionally, the more humid the ambient
conditions, the more frost may build up. Keep the door closed as much as
possible and avoid opening the door unnecessarily to minimize frost
build-up.
If frost is preventing the door from closing properly, you may need to
power the unit off until the frost melts. Use a soft absorbent towel to dry
the unit. Some defrost water will drain into the drip dish on the
compressor and the water will be evaporated by the compressor.
WARNING: Never attempt to remove frost with a sharp object!
Preparing the Wine and Beverage Cooler for Storage
If the wine and beverage cooler will not be used for a long time, or is to be
moved to another place, it will be necessary to defrost the unit and dry the
interior.
IMPORTANT:
• Do not touch the power plug
when your hands are wet.
• Never unplug the unit by
pulling on the plug.
1. Disconnect the cooler from the power supply by removing the power
plug from the wall socket.
2. Leave the door open to allow for air circulation and to prevent mold,
mildew and unpleasant smells.
CAUTION: Store the unit out of the reach of children. If you have children,
you may want to take additional precautions such as removing the door to
prevent a child from being trapped inside the cooler!
EdgeStar Wine and Beverage Cooler
10
CLEANING AND MAINTENANCE
Periodic cleaning and proper maintenance will ensure efficiency, top
performance and long life.
Exterior Cleaning
The door and cabinet may be cleaned with a mild detergent and
lukewarm water solution such as two (2) tablespoons of baking soda to
one (1) quart of water.
Do not use solvent based or abrasive cleaners. Use a soft sponge and
rinse with clean water. Wipe with a soft clean towel to prevent water
spotting. If the door panel is stainless steel, it can discolor when exposed
to chlorine gas and moisture. Clean stainless steel with a cloth dampened
with a mild detergent and warm water solution. Never use an abrasive or
caustic cleaning agent.
Interior Cleaning
The wine and beverage cooler’s interior should be cleaned occasionally.
1. Disconnect power to the unit.
2. Open the door and remove the contents and shelves.
3. Wait until the unit defrosts.
4. With a clean cloth, wipe down the interior of the unit.
5. Reinsert the shelves and beverages.
6. Reconnect power to the unit.
TROUBLESHOOTING
Before Calling for Help
If the unit appears to be malfunctioning, read through the OPERATION
section of this manual first. If the problem persists, check the
Troubleshooting Guide below and on the following page. The problem
could be something that can easily be solved or explained.
Symptoms
The wine and beverage
cooler turns on and off
frequently.
11
Possible causes
Solutions
The room temperature is
higher than the
recommended ambient
environment.
Run the cooler at the appropriate ambient temperature.
The door is being opened
often.
Minimize the number of times the door is opened.
The door is not completely
closed.
Make sure the door is completely closed.
The door gasket is not
sealing properly.
Make sure the door gasket is properly sealing.
The cooler does not have the
suggested ventilation.
Read and follow the “Installation Clearance
Requirements” section.
Troubleshooting continued
Issue
The wine and beverage
cooler does not turn on.
The wine and beverage
cooler will not reach the
desired temperature
The wine and beverage
cooler is making strange
noises
The body of the wine and
beverage cooler is
electrified.
Frost is forming in the
wine and beverage
cooler.
Possible cause
Solution
There is a power failure.
Ensure the cooler is plugged in and the power outlet has
power.
The cooler is not plugged in.
Plug the unit in to a power outlet that has sufficient
amperage.
A house fuse has blown or
the circuit breaker is tripped.
Replace the broken fuse in your fuse box or reset the
breaker.
The cooler is placed too
close to a heat source.
Keep the cooler away from direct sun light or other heat
sources.
The cooler does not have
sufficient ventilation.
Read and follow the “Installation Clearance Requirements”
section.
The door is opened too
frequently or for a long
period of time.
Close the door tightly and do not open the door too
frequently or for a long period of time.
Certain sounds are normal.
Read the “Normal Sounds” section.
The unit is not level or is
touching another appliance.
Check to make sure that the cooler is level, and that it is
not in contact with another appliance or furniture.
The unit is not grounded
properly.
Contact your local electrician to test your electrical
grounding system.
The environment is humid.
Though the unit uses an “auto-defrost” system, under
certain conditions, manual defrosting may be required. If
frost builds up, you can try running the cooler on a warmer
temperature setting, minimizing the number of times you
open the door, or unplugging the unit to allow the frost to
melt.
The ambient temperature is
too low.
The door is being opened
too frequently.
Your cooler is not level.
The door gasket is dirty.
The door will not shut
properly.
Make sure the cooler is on a level surface.
Clean the door gasket.
The door gasket is not
installed correctly.
Make sure the door gasket is properly installed.
The shelves are incorrectly
installed.
Correctly install the shelves.
EdgeStar Wine and Beverage Cooler
12
Specifications
Description of product
Built-in Wine And Beverage
Cooler
Model
CWB1760FD
Voltage/Frequency
AC 115V~60Hz
Amperage
1.0A
Input Power
100W
Color
Black Cabinet; Stainless Steel
Doors
Storage Capacity
17 Bottles*, 60 standard 12oz.
cans
Refrigerant
R600a, 0.85 oz.
Temperature Range
36 - 43ºF Left Zone
41 - 72ºF Right Zone
Dimensions
(Height x Width x Depth )
32” x 23.5” x 24.4”**
Net Weight
95 lbs.
Note: Technical data and performance information is provided for
reference only.
Specifications are subject to change. Check the rating label on the wine
and beverage cooler for the most accurate information.
*Note on wine storage capacity:
The wine and beverage cooler will store 17 standard 750 ml. wine bottles.
**Depth includes the handle.
13
Limited Warranty: Full One-Year Parts and Labor
This product is warranted by EdgeStar and is subject to any conditions set forth as follows:
WHAT IS COVERED:
For a period of ONE (1) YEAR from the date of
original retail purchase, EdgeStar will repair or
replace any part free of charge including labor
that fails due to a defect in materials or
workmanship. Labor will be performed free of
charge at an authorized EdgeStar repair facility
and EdgeStar will supply new, rebuilt, or
refurbished parts free of charge. EdgeStar may
request a defective part be returned in
exchange for the replacement part. All
replacement parts or products will be new,
remanufactured, or refurbished. All products and
parts replaced by EdgeStar under warranty
service become the property of EdgeStar. After
the 12 month period, EdgeStar will no longer be
responsible for labor charges incurred or
replacement parts. All defective products and
parts covered by this warranty will be repaired or
replaced on a mail-in basis to an EdgeStar
authorized repair facility.
This warranty applies to the original purchaser
only, and only covers defects in workmanship
experienced during operation of the product
under normal service, maintenance, and usage
conditions. This warranty applies to the purchase
and use of this product in residential settings
within the United
States of America.
Exceptions: Commercial or Rental Use
Warranty
90 days labor and parts from date of original
purchase. No other warranty applies.
WHAT IS NOT COVERED- The following limitations apply to the
coverage of this warranty. This warranty does not cover:
-Labor charges for installation, setup or training to use the
product.
-Shipping damage, and any damage caused by improper
packaging for shipment to an authorized service center, and any
damaged caused by improper voltage or any other misuse,
including abnormal service, handling, or usage.
-Cosmetic damage such as scratches and dents.
-Normal wear and tear on parts or replacement of parts designed
to be replaced, e.g. filters, cartridges, batteries.
-Service trips to deliver, pick-up, or repair, install the product, or to
instruct in proper usage of the product.
-Damages or operating problems resulting from misuse, abuse,
operation outside environmental specifications, uses contrary to
instructions provided in the owner’s manual, accidents, acts of
God, vermin, fire, flood, improper installation, unauthorized
service, maintenance negligence, unauthorized installation or
modification, or commercial use.
-Labor, service transportation, and shipping charges for the
removal and replacement of defective parts, beyond the initial 12
month period.
-Products that have been modified to perform outside of
specifications without the prior written permission of EdgeStar.
-Products lost in shipment, or theft.
-Products sold AS IS or from an unauthorized reseller.
-Products that have had their serial numbers removed, defaced,
or with serial numbers that have been invalidated.
-Damage from other than normal household use.
-Replacement or repair of household fuses, circuit breakers, wiring
or plumbing.
-Damage to personal property from use of product.
-Damage from service other than from an authorized EdgeStar
repair facility.
-Hoses, knobs, lint trays and all attachments, accessories and
disposable parts.
-Any service charges not specifically identified as normal such as
normal service area or hours.
-Any special or consequential damages arising out of the use of
the product.
OBTAINING WARRANTY SERVICE: If you believe your product is defective, contact EdgeStar Customer Support for
troubleshooting assistance and warranty service at www.edgestar.com or call 1-866-319-5473. Before contacting
Customer Support you are required to have your model number, serial number and proof of purchase available upon
request. Once an EdgeStar authorized representative has confirmed that your product is defective and eligible for
warranty service, the product must be returned to an EdgeStar authorized repair facility. EdgeStar is not responsible for
damage resulting from shipper mishandling or improper packaging. Do not return a defective product to the place of
purchase. Products received without a return authorization number will be refused.
THISWARRANTYISINLIEUOFANYOTHERWARRANTY,EXPRESSORIMPLIED,INCLUDINGWITHOUTLIMITATION,ANYWARRANTYOFMERCHANTABILITYOR
FITNESSFORAPARTICULARPURPOSE.TOTHEEXTENTANYIMPLIEDWARRANTYISREQUIREDBYLAW,ITISLIMITEDINDURATIONTOTHEEXPRESSWARRANTY
PERIODABOVE.NEITHERTHEMANUFACTURERNORITSDISTRIBUTORSSHALLBELIABLEFORANYINCIDENTAL,CONSEQUENTIAL,INDIRECT,SPECIAL,OR
PUNITIVEDAMAGESOFANYNATURE,INCLUDINGWITHOUTLIMITATION,LOSTREVENUESORPROFITS,ORANYOTHERDAMAGEWHETHERBASEDIN
CONTRACT,TORT,OROTHERWISE.SOMESTATESDONOTALLOWTHEEXCLUSIONOFINCIDENTALORCONSEQUENTIALDAMAGES,SOTHEABOVEEXCLUSION
MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
EdgeStar Products
500 N. Capital of TX Hwy, Bldg 5
Austin, TX 78746
Toll Free: 1-866-319-5473
Web: http://www.edgestar.com
E-mail: [email protected]
Register your product, download owner’s manuals, access additional troubleshooting
resources, and obtain more information on other great EdgeStar products on the web at:
http://www.edgestar.com
Product contents and specifications may change without notice.
Copyright © 2014 Living Direct, Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement