Table of Contents

Table of Contents
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
Table of Contents
1. Application ................................................................................................................. 4
2. General product information..................................................................................... 4
2.1. DALI Bus system properties ...................................................................... 4
2.2. DALI gateway REG-K/1/16(64)/64/ IP1 product properties ....................... 4
3. General properties of the ETS application program: DALI gateway IP Plug-in ... 5
3.1 Installing the Plug-In .................................................................................... 5
3.2 Principal structure of the Plug-In ................................................................ 6
3.3 Operating modes of the Plug-In: DALI commissioning ............................ 6
4. DALI commissioning ................................................................................................. 7
4.1 Commissioning the gateway via website or pushbuttons ....................... 7
4.2 The commissioning process with gateway via ETS Plug-In .................... 8
5. Display and push button control .............................................................................. 9
6. Control via web browser ........................................................................................... 12
6.1 Configuration buttons .................................................................................. 13
6.2 Control buttons............................................................................................. 14
6.3 ECG fields ..................................................................................................... 14
6.4 Group fields .................................................................................................. 15
6.5 Information and status fields ...................................................................... 15
7. ETS special and commissioning functions ............................................................. 17
7.1 Special functions in ‘Normal mode‘............................................................ 17
7.1.1 Synchronisation with the connected DALI line ...................................... 17
7.1.2 User-friendly names for ECGs and groups ............................................. 18
7.2 Special functions in ‘Extended Mode‘ ........................................................ 18
7.2.1 Preparing and planning the DALI commissioning in ‘Extended Mode‘ 19
7.2.2 DALI commissioning in ‘Extended Mode‘ ............................................... 20
7.2.3 ECG and lamp faults during DALI commissioning in ‘Extended Mode‘21
7.2.4 Using dummy ECGs in ‘Extended Mode‘ ................................................ 22
7.3 General extra functions in the ETS ............................................................. 22
7.3.1 Using IP for plug-in communication ........................................................ 22
7.3.2 Parameter templates ................................................................................. 23
7.3.3 DALI configuration data back-up ............................................................. 23
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 1 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
8. DALI maintenance and expansion............................................................................ 24
8.1 Quick exchange of individual ECGs ........................................................... 24
8.2 Extending the existing system – post-installation .................................... 24
9. Different operating modes ........................................................................................ 25
9.1 Normal mode ................................................................................................ 25
9.2 Permanent mode .......................................................................................... 25
9.3 Staircase mode ............................................................................................. 25
9.4 Night Mode .................................................................................................... 25
9.5 Panic / Emergency mode ............................................................................. 25
9.6 Test mode for central battery emergency luminaires ............................... 25
9.7 Burn-in mode ................................................................................................ 26
9.8 Operating mode hierarchy ........................................................................... 26
10. Analysis and service functions .............................................................................. 27
10.1 Recording operating hours ....................................................................... 27
10.2 Individual fault recognition at ECG level.................................................. 27
10.3 Fault analysis at group level ..................................................................... 28
10.4 Fault analysis at device level .................................................................... 28
11. Scenes and effects .................................................................................................. 29
11.1 The scenes module .................................................................................... 29
11.1.1 Scene programming via the scene website .......................................... 29
11.1.2 Scene programming via ETS in ‘Extended Mode‘ ................................ 30
11.2 The effect module ....................................................................................... 30
11.2.1 Effect programming using the effects website .................................... 30
11.2.2 Effect programming via ETS in ‘Extended Mode‘ ................................ 31
12. Self-contained battery emergency lamps .............................................................. 32
12.1 Features ...................................................................................................... 32
12.2 Converter inhibit mode .............................................................................. 32
12.3 Test mode ................................................................................................... 32
13. ETS communication objects overview .................................................................. 34
13.1 General communication objects ............................................................... 34
13.2 ECG-related communication objects........................................................ 37
13.3 Group-related communication objects..................................................... 38
14. ETS parameter settings ........................................................................................... 40
14.1 Device: General Settings ........................................................................... 40
14.1.1 Parameter page: General ........................................................................ 40
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 2 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
14.1.2 Parameter page: IP Settings ................................................................... 40
14.1.3 Parameter page: Behaviour .................................................................... 41
14.1.4 Parameter page: Special Functions....................................................... 42
14.1.5 Parameter page: Analysis and Service ................................................. 42
14.2 ECG No. xx .................................................................................................. 43
14.2.1 Parameter page: ECG No. xx .................................................................. 43
14.2.2 Parameter page: Emergency Settings ................................................... 45
14.2.3 Parameter page: Switching Behaviour.................................................. 46
14.2.4 Parameter page: Analysis and Service ................................................. 47
14.3 Group Nr. xx ................................................................................................ 47
14.3.1 Parameter page: Group number xx ....................................................... 47
14.3.2 Parameter page: Switch behaviour ....................................................... 48
14.3.3 Parameter page: Analysis and Service ................................................. 49
15. Firmware update ...................................................................................................... 50
16. Reset to conditions at delivery ............................................................................... 50
Schneider Electric Industries SAS ................................................................................ 50
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 3 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
1. Application
2.2. DALI gateway REG-K/1/16(64)/64/
IP1 product properties
Product family:
Product type:
Manufacturer:
Interfaces/Gateways
DALI gateway
Schneider Electric
Name:
KNX DALI gateway REG-K/
1/16(64)/64/IP1
MTN6725-0001
The KNX DALI gateway REG-K/1/16(64)/64/IP1 (referred
to below as the gateway) is a device used to control
ECGs with a DALI interface via the KNX installation bus.
The device transforms switch and dim commands from
the connected KNX system into DALI telegrams and
status information from the DALI bus into KNX telegrams.
The gateway is a Category 1 device (in accordance with
EN 62386-103). This means the device must only be
used in DALI lines with connected ECGs and not with
other DALI control devices within the line (No multimaster function).
Power supply for the up to 64 connected ECGs comes directly from the gateway. An additional DALI power supply
is not required and not permitted.
Order number:
2. General product information
2.1. DALI Bus system properties
The cross-functional DALI-Bus (DALI = Digital Addressable Lighting Interface) is a system used to control electronic ballasts (ECGs) in lighting technology. The specifications of the DALI communications interface are set in
the international norm IEC 60929.
The DALI Bus enables the receipt of switch and dim
commands. In addition, the DALI can be used for the notification of a fault status such as light or ECG failure or
for other light status information. In line with the latest
DALI standard, devices with emergency light function
(EN 62386-202) are also supported. Status and operating mode of emergency lights can be monitored and different testing procedures can be performed.
Via the connected control device / gateway (Master), up
to 64 individual DALI ECGs (Slaves) can be connected in
a DALI line. When the DALI is commissioned, the ECGs
receive an automatically generated 3 byte long address.
Based on the long address a short address between 0
and 63 is assigned during the further commissioning
process. As the address assignment is automatic, the
device order is random. The individual ECGs/lights therefore need to be identified during the further commissioning process (see below).
The addressing of individual ECGs in the system is either
based upon the short address (individual addressing) or
upon a DALI group address (group addressing). For this
purpose, any number of ECGs within a line can be assigned into up to 16 groups. The group addressing in the
DALI system guarantees that switch and dim processes
of different lights within a system are performed simultaneously without imposition of time delays.
In addition to short and group addresses, the light values
of individual DALI ECGs can also be merged into scenes
and addressed via scene addresses.
For a detailed description of the DALI system, please see
the DALI handbook at www.dali-ag.org
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
The device comes in a 4 modules wide DIN Rail casing
so it can be directly integrated into the mains distribution
box.
In addition to the pure gateway functions, the gateway offers numerous additional features:

Addressing of 16 DALI groups and/or individual addressing of up to 64 ECGs

Flexible DALI commissioning concept: directly on the
device or via the integrated web server

Different operating modes for groups and ECGs such
as permanent mode, night-time mode or staircase
mode

Burn-in mode for each individual light with specific
burn-in time settings

Integrated reader to count the operating hours of
each light with an alarm to signify the end of its life
span
Seite 4 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a

Individual fault recognition with objects for each
light/ECG

Complex fault analysis at group and device level with
number of faults and calculation of fault rates

Fault threshold monitoring with individually adjustable
threshold values

Scene module for extensive scene programming of
groups and individual ECGs

Effect module for sequence control and light effects

“Easy replacement function“ for the quick and easy
replacement of faulty ECGs

Test mode for centrally powered emergency light systems

Support of self-contained emergency ballasts

Support of testing procedures for emergency lights
with date and time stamp

Integrated web server with extensive commissioning
and maintenance possibilities

Integrated “visualisation“ via web-browser for direct
control and display
3. General properties of the ETS application program: DALI gateway IP Plugin
3.1 Installing the Plug-In
The application for the gateway is based on a powerful
KNX communications stack of the System-B type. It is
designed as plug-in for ETS-3 and ETS-4. The plug-in
design means that an additional installation process is
necessary. All program files that are required are automatically set up when you import the corresponding ETS
product file (vdx file).
After the import the product can be integrated as usual
into the ETS. It can be found under product family “Lighting“ and product type “Gateway“.
When you first load the product in the ETS, you need to
start the installation of the required plug-in files by pressing the ‘Next‘ button.
|
Please check the IPAS software license conditions before you start the installation. With the
installation you accept the conditions.
If the installation has been successful, a notification window appears.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 5 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
3.3 Operating modes of the Plug-In:
DALI commissioning
In principle, the plug-in can be used in the two different
operating modes “Normal mode“ and “Extended mode“.
Depending on the concept needed for the DALI commissioning, you can select the required mode in the menu
‘Tools‘  ‘Options‘.
Attention: The PC must have .NET Version 4.0 as a requirement for the installation. Normally the framework exists on any modern PC. Should an older version of .NET
be installed or no version at all, you need to update .NET
first. Please see the Microsoft website for the required
setup.
3.2 Principal structure of the Plug-In
The gateway is a high-functionality product and accordingly offers many different setting options within the parameters. To make the overview of the parameters as
simple and transparent as possible for the system integrator, there are more operating levels than with a standard ETS application.
Unlike with the standard applications, there is not only a
parameter page for each device within the main parameter directory on the left-hand side but also several subpages which can be selected via a register at the top of
the page. Use the main directory to select the element
you require “General ECG No XX, Group No XX“ and the
sub-pages to set the parameters of the selected element.
This structure is different from a standard device.
You can also use the three menus “Data, Tools and
Help“ in the header of the plug-in window to perform
some of the main functions and settings.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
The choice of the commissioning concept depends on
the preferences of the system integrator as well as the
technical requirements of the project. If you choose option A ‘Normal Mode‘ the DALI configuration and commissioning must be performed via the website of the device. This means that all project gateways - at least during the commissioning phase - must be integrated into an
IP network via the IP interface. (The network can also be
a simple cross-link cable connection between the gateway and the configuration PC.)
If no IP network is available, only a limited commissioning
process is possible via the display and push-buttons on
the device. However, if you choose commissioning option
B “Extended Mode“ the whole commissioning process
can be performed via ETS and KNX. No IP network is
required in this case. Mode B also gives you the opportunity to configure individual ECGs ‘offline‘ in the ETS,
i.e. before they are commissioned in the installation.
However, in this case all objects and parameters are
visible. The synchronisation that simplifies the ETS and
brings it in line with the actual system is not possible.
To decide which mode to use you should answer the following three questions:

Is the DALI gateway (at least temporarily during the
commissioning process) integrated into an IP network?
o Yes  Mode A or mode B
o No  Mode B

Do you want to set the DALI configuration and parameters ‘offline‘ in the ETS prior to the commissioning of the installation?
o Yes  Mode B
Seite 6 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a

Do you want to perform the DALI configuration and
set the parameters on the construction site and synchronise the ETS with the real installation to simplify
it?
o Yes  Mode A
Mode A: ’Normal Mode‘ --- Mode B: ’Extended Mode‘
If the conditions permit it, we recommend using ‘Normal
Mode‘, especially for integrators who are not too familiar
with the DALI system because the large number of possible parameter settings and objects can be automatically
reduced to those elements that are actually required. The
standard setting after the initial installation of the plug-in
is therefore mode A.
Please remember that whichever operating mode you select, it applies to all gateways within a project and ETS. It
is not possible to select mode A for some and mode B for
others.
4. DALI commissioning
As explained above, the work flow for the commissioning
of a DALI line differs depending on the selected concept.
The following chart shows the general procedure:
DALI gateway IP Plug-in
Plug-In Mode A
Normal Function
WEB
KNX
Plug-In Mode B
Extended Function
Electrical Installation
Parameter setting and Adjustment in ETS
Teach-In of connected DALI
ECGs
Electrical Installation
Identification and Assignment of
DALI ECGs and Groups
Teach-In of connected DALI
ECGs
Synchronisation of connected
system with ETS
Identification and assignment of
DALI ECGs and groups
Parameter setting and adjustment in ETS
Programming of DALI data in
connected ECGs
Loading of ETS program in DALI gateway
4.1 Commissioning the gateway via
website or pushbuttons
If you select option A, i.e. commissioning the device via
the website or pushbuttons, please use the following procedure:
Following the physical installation and wiring of the ECGs
and lights and the electronic commissioning, the connected ECGs need to be taught. During the teach-in
process, all DALI ECGs are automatically recognised
and each ECG is assigned a short address between 0
and 63.
You can start this process either via the push buttons
and menu on the device display (see below display and
push button control) or via the commissioning website
(see below control via web browser).
The order within a DALI line is completely random. You
therefore need to identify the ECGs and - if required - assign them to groups. Identification and group assignment
can also be performed via the device itself (push buttons,
display) or via the website. If you use the website for
identification, you can give each ECG an individual name
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 7 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
(e.g. office-left). If you want to control the ECG within a
DALI group rather than individually, you can at this point
assign it to a group.
Once you have identified all ECGs and, if required,
named and assigned them, you need to synchronise the
ETS application. During the synchronisation, the system
properties of the connected DALI line are transferred to
the ETS and the parameters and communication objects
are configured accordingly. This means that after the
synchronisation only objects and parameters of actually
existing ECGs are visible to the user. The application is
thereby optimised and simplified. ECG and group names
are also transferred to the ETS. To start the synchronisation, press the respective button on the ETS parameter
page (see below ETS application program).
Once the synchronisation is complete, you can configure
the individual ECG or group parameters in the ETS and
connect communication objects with group addresses.
When you have finished the configuration, simply load
the ETS application onto the device.
In principle, the installation is now ready for operation
and function testing. However, if you would like to also
program scenes or effects, you can do so via the push
buttons and display on the device (only scenes, limited
functionality) or via the web site (scenes, effects without
limitation).
For a complete description of the display and pushbutton control required for the commissioning, please see
chapter 5. For a description of the website function,
please refer to chapter 6.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
4.2 The commissioning process with
gateway via ETS Plug-In
Instead of commissioning via web browser or pushbuttons, the DALI can also be entirely commissioned via
KNX and the plug-in. This mode B option enables a
largely ‘off-line configuration’ of the DALI installation. Parameters for ECGs and groups as well as communication
objects can be completely configured before the electrical
installation. Names can be assigned in advance and the
setting of scenes and effects is also possible ‘offline‘.
This means that the system integrator who uses the ETS
and the electrician who works on the actual installation
can work independently of each other. Once the electrical installation is complete, the actual DALI commissioning can also be performed with ETS.
The first thing to do is to start the teach-in process. During this process all connected DALI ECGs are automatically recognised and each ECG is assigned a random
short-address between 0 and 63. You can now identify
the randomly ordered ECGs/lamps by selecting a respective operation (on/off/blinking) in the ETS. Use dragand-drop to pull an ECG into the ECG position previously
set in the ETS. The random order is thus ‘dissolved‘ and
the installation is now well-structured.
When you download the DALI configuration, the configured data is downloaded onto the ECGs and if applicable the short-addresses are amended in line with the preconfiguration. Once you have programmed all DALI data,
load the actual ETS application onto the gateway.
For a detailed description of the ETS commissioning interface, please see chapter 7.
Seite 8 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
5. Display and push button control
MAINTANANCE
ECG/LAMP
You can commission the connected DALI line and set
and change DALI parameters via the three push buttons
(MOVE, Set/Prg, ESC) and the 2x12 character display on
the front of the device. The user concept is menu-based.
Depending on the menu position, you can select two sublevels. The current menu position is shown on the display. To navigate within the menu, press the push buttons briefly. Use the MOVE button to select the next
menu item on the same level. Use the Prg/Set button to
go to the next lower level. Press the ESC button to leave
a level and return to the next higher level.
Main menu– Level 1
The main menu (Level 1) has the following structure:
DALI GATEWAY
IP – V1.0
NETWORK
IP ADDRESS
The product name and firmware version are
displayed. The sub-menu can be used to set the
display language.
The sub-menu displays the IP address set in
the ETS or assigned by the DHCP-Server
CONVERTER INHIBIT MODE
When a DALI line is newly installed, use the
sub-menu to reset the connected DALI devices
and automatically search for ECGs.
POST
INSTALLATION
Use the sub-menu to start the automatic search
process and possibly adjust the configuration
following a post-installation of DALI ECGs.
ECG EASY REPLACEMENT
GROUP
ASSIGNMENT
SCENE
ASSIGNMENT
Use the sub-menu to active the ECG easy replacement function and possibly program and
integrate individually replaced ECGs into the
system.
Use the sub-menu to identify ECGs and assign
them to DALI groups. .
Use the sub-menu to assign groups to DALI
scenes
Sub-menu DALI GATEWAY – Level 2
DALI GATEWAY
IP – V1.0
SCENE
TEST
SYSTEM
TEST
Use the sub-menu to switch both the whole installation (broadcast) and individual channels for
test purposes.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
The currently set display language is shown.
Hold the Prg/Set button to change into programming mode. Use the MOVE button to
choose from one of the following languages:
GERMAN, ENGLISH, FRENCH, SPANISH,
ITALIAN, DUTCH, SWEDISH, DANISH.
Briefly press the Prg/Set button again to save
the configuration. The display now works in
the selected language.
NETWORK
IP ADDRESS
Briefly press the Prg/Set button to change
from the main menu IP ADDRESS to the submenu.
DHCP: 192.
168.004.101
The sub-menu displays the IP address currently set in the ETS or assigned by the
DHCP-Server.
Sub-menu NEW INSTALLATION – Level 2
SEARCH ECGs
via PROG-MODE
Use the sub-menu to test individual scenes.
Use the sub-menu to load any existing system
faults.
Briefly press the Prg/Set button to change
from the main menu DALI GATEWAY to the
sub-menu LANGUAGE.
Sub-menu NETWORK IP_ADDRESS – Level 2 and 3
NEWINSTALLATION
GROUP
TEST
Use the sub-menu to activate the converter inhibit mode in the installation phase.
To perform a function or change a configuration within a
sub-menu, go to the respective position and change into
programming mode. To change into programming mode,
hold the Prg/Set button for more than 2 seconds. Once
the function is in programming mode, a symbol appears in the display. If the programming mode is active,
use the MOVE button to change a parameter or setting.
Briefly press the Prg/Set button again to complete the
process and save the set parameter or activate the function.
LANGUAGE
GERMAN
NEW
INSTALLATION
Use the sub-menu to start the burn-in mode for
ECGs and to re-set operating hours.
FOUND
ECGs: 47
Briefly press the Prg/Set button to change
from the main menu NEW INSTALLATION to
the sub-menu SEARCH ECGs via PROGMODE.
Hold the Prg/Set button to change into programming mode. Briefly press the Prg/Setbutton again to start the initialisation and
search process. First, all ECGs connected to
the DALI line are automatically reset and any
previously set parameters and group assignments are deleted. The device then searches
for the connected ECGs via their random long
address. The ECGs are automatically recognised in ascending order. Depending on the
Seite 9 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
number of connected ECGs the search process may take a few minutes. Once the process is complete, the number of ECGs found is
shown on the display. Press the ESC button
(or wait for about 30 seconds) to return to the
level above.
Sub-menu GROUP ASSIGNMENT – Level 2 and 3
GROUP
ASSIGNMENT
Sub-menu POST-INSTALLATION – Level 2
POST
INSTALLATION
SEARCH ECGs
via PROG-MODE
DELETED
ECGs: 3
NEW
ECGs: 1
DEL./NEW
ECGs: 3/1
Briefly press the Prg/Set button to change
from the main menu POST- INSTALLATION
to the sub-menu SEARCH ECGs via PROGMODE.
Hold the Prg/Set button to change into programming mode. Briefly press the Prg/Setbutton again to start the verification and
search process. The device searches for the
connected ECGs via their long address and
automatically compares them to the previous
configuration.
If ECGs have been removed from the DALI
line, the entries are deleted from the device.
The number of deleted devices is displayed
during the verification process.
After that, the DALI line is searched for newly
installed devices. Newly added ECGs are
automatically reset and any previously programmed parameters and group assignments
are deleted. Depending on the number of
connected ECGs the search process may
take a few minutes. During the search process, the number of newly found devices is
shown on the display.
Once the whole process (verification and
search) is complete, the display shows both
the deleted and the newly found ECGs (deleted devices / new devices from left to right,
see picture on the left). Press the ESC button
(or wait for about 30 seconds) to return to the
level above.
ECG No.: 12
GROUP:
--
CONV. No.: 13
GROUP: --
ECG No.: 12
GROUP: 1
SEARCH ECGs
via PROG-MODE
ECG 04
REPLACED
ERROR
TYPE 07
Briefly press the Prg/Set button to change
from the main menu ECG EASY REPLACEMENT to the sub-menu SEARCH ECGs via
PROG-MODE.
Hold the Prg/Set button to change into programming mode. Briefly press the Prg/Setbutton again to start the easy replacement.
The device first checks if one or several
ECGs in the system were faulty. It then automatically looks for newly connected ECGs in
the line. The easy replacement is only possible if just one ECG in the line was faulty and
one new ECG is found. If the process is successful, the number of the replaced ECG is
shown. If the search process cannot be completed because the required conditions are
not met, an error code appears in the display.
The error codes have the following meaning:
Error Type 7: No ECG failure
Error Type 8: More than one ECG failure
Error Type 9: No new ECG can be found
Error Type 10: ECG has wrong device type
Error Type 11: More than one new ECG
Press the ESC button (or wait for about 30
seconds) to return to the level above.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Briefly press the MOVE button to run through
the different ECGs. The number of the selected ECG is shown in the first display line.
As long as the ECG is selected, the connected lamp is flashing. The programmer can
thereby determine which lamp is assigned to
the number.
If the selected device is a non-switchable
converter for emergency lights, the selection
sets the device into function test mode and
the display shows the word CONV. For identification purposes, the function LED on the
converter flashes during the test (see user
manual for the converter).
Hold the Prg/Set button to change into programming mode. Briefly press the MOVE button again to select the group that you want to
assign the ECG to. If the group is selected,
briefly press the Prg/Set button to confirm and
save the setting. You must repeat this process once for every ECG during the initial installation. Attention: non-switchable converters for emergency lights cannot be assigned
to a group.
Press the ESC button (or wait for about 30
seconds) to return to the level above.
Sub-menu SCENE ASSIGNMENT – Level 2 and 3
SCENE
ASSIGNMENT
Sub-menu ECG QUICK EXCHANGE – Level 2
ECG EASY
REPLACEMENT
Briefly press the Prg/Set button to change
from the main menu GROUP ASSIGNMENT
to the sub-menu.
Within this menu the individual ECGS that
were found during the search process can be
assigned to 16 DALI groups and previous assignments can be modified.
SCENE01 XXXX
XXXXXXXXXXXX
SCENE03 ---XXXX------XX
Briefly press the Prg/Set button to change
from the main menu SCENE ASSIGNMENT
to the sub-menu. Within the menu the DALI
groups can be assigned to up to 16 possible
scenes. Individually controlled ECGs cannot
be assigned via the display. To assign individual ECGs, you must use the website.
Briefly press the MOVE button to run through
the individual scenes. The number of the selected scene is shown in the first display line.
Behind the scene number, different characters show which of the 16 groups are assigned to the scene. An X means that a group
is assigned to the scene. A – means the
group is not assigned to the scene. The four
characters directly behind the scene number
in the first display line represent groups 1 - 4
(from left to right). The 12 characters in the
second display line represent groups 5 – 16
(from left to right).
Hold the Prg/Set button to change into programming mode. A flashing cursor on the first
X means that group 1 is selected. By briefly
pressing the MOVE button you can toggle between X and – symbols to choose whether
you would like to assign the group to the
scene. Briefly press the Prg/Set-button to
move the cursor to the next group. Once you
have run through all 16 groups, the setting is
saved and used during further scene programming. After you have pressed the
Prg/Set button a final time, the display automatically returns to the level above. Press the
ESC button to return to the level above without saving the changes you have made.
Seite 10 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
Sub-menu GROUP TEST – Level 2 and 3
GROUP
TEST
GROUP: 6
TEST
GROUP: 6
->on
Briefly press the Prg/Set button to change
from the main menu GROUP TEST to the
sub-menu. Within the menu, groups can be
switched either individually or all together
(ALL GROUPS TEST) to test the installation.
LAMP 17
Fault
Briefly press the MOVE button to run through
the individual groups. The number of the selected group is shown in the first display line.
Hold the Prg/Set button to change into programming mode. Briefly press the MOVE button to select whether you would like to switch
the group on or off. Briefly press the Prg/Set
button to execute the selected command.
Press the ESC button (or wait for about 30
seconds) to return to the level above.
Sub-menu MAINTENANCE ECG/LAMP– Level 2 and 3
MAINTANANCE
ECG/LAMP
Sub-menu SCENE TEST – Level 2 and 3
SCENE
TEST
SCENE: 2
TEST
SCENE: 2
->invoke
Briefly press the Prg/Set button to change
from the main menu SCENE TEST to the
sub-menu. Within the menu you can invoke
all scenes for test purposes or program newly
set light scenarios into the scene.
Briefly press the MOVE button to run through
the individual scenes. The number of the selected scene is shown in the first display line.
Hold the Prg/Set button to change into programming mode. Briefly press the MOVE button to choose whether you would like to invoke or save a scene. Briefly press the
Prg/Set-Taste button to execute the selected
command and either invoke or save the
scene. Press the ESC button (or wait for
about 30 seconds) to return to the level
above.
Sub-menu SYSTEM TEST – Level 2 and 3
SYSTEM
TEST
DALI
No fault
DALI
Fault




DALI short-circuit
Lamp fault with the lamp or ECG
number being displayed
ECG fault with the ECG number
being displayed
No KNX bus
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
ECG No.: 01
368 h
ECG No.: 01
BURNIN
ECG No.: 01
BURNIN/RES.
Briefly press the Prg/Set button to change
from the main menu MAINTENANCE
ECG/LAMP to the sub-menu. Within the
menu you can start the burn-in of a lamp and
reset the reader for its operating hours.
Briefly press the MOVE button to run through
the individual ECGs. The number of the selected ECG is shown in the first display line.
Line 2 shows the number of operating hours
since the last reset / burn-in.
Hold the Prg/Set button to change into programming mode. Briefly press the MOVE button to toggle between the functions BURN-IN,
RESET, BURN-IN/RESET. Briefly press the
Prg/Set button to execute the selected command. Press the ESC button (or wait for
about 30 seconds) to return to the level
above.
Sub-menu CONVERTER INHIBIT MODE – Level 2
CONVERTER INHIBIT MODE
Briefly press the Prg/Set button to change
from the main menu SYSTEM TEST to the
sub-menu. Within the menu you can check for
any potential faults.
If there is no fault, this is shown in the display.
The following faults can be recognised by the
system. They are shown in the display and
also simultaneously set off the red error LED:
If there has been a DALI short-circuit, no further faults can be recognised. For all other
fault types, several faults can be recognised
at the same time. Within the menu you can
toggle between the different faults by briefly
pressing the MOVE button. The number of
the ECG is displayed for both lamp and ECG
faults. This means that a fault can be easily
localised. Press the ESC button (or wait for
about 30 seconds) to return to the level
above.
INHIBIT
via PROG-MODE
CONVERTER
INHIBIT?
Briefly press the Prg/Set button to change
from the main menu CONVERTER INHIBIT
MODE to the sub-menu. Within the menu you
can turn on the Inhibit Mode for all connected
self-contained battery emergency lamps.
If the mains power supply is turned off within
15 minutes from activating the Inhibit Mode,
the lights do not change into emergency
mode but remain switched off. Particularly
during the initialisation phase of a building
this operating mode may be required to prevent the emergency lights from being turned
on constantly.
Hold the Prg/Set button to change into programming mode. Briefly press the Prg/Set
button again to activate the Inhibit Mode.
Press the ESC button (or wait for about 30
seconds) to return to the level above.
Seite 11 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
6. Control via web browser
In addition to the push buttons, you can also easily commission the DALI via the integrated web server. For this
purpose connect the gateway directly to the IP network.
An RJ-45 socket is located above the KNX bus connector
at the bottom left-hand side of the device.
interface are set to DHCP address assignment. If there is
a DHCP server in the network the device automatically
receives an IP address after initialisation. This address is
shown on the device display (see above). If no DHCP
service is available or if you would rather use a fixed IP
address, you must set the address either via ETS or the
device display. You may also need to configure the subnet mask and standard gateway (for direct access via the
Internet). Those two parameters can only be configured
in the ETS.
Once the IP address has been assigned, load the device
website via any web browser (e.g. Microsoft Internet Explorer, Mozilla Firefox, Apple Safari). Simply enter the
correct IP address (URL) in the browser.
|
Please remember that the complete URL consists of the IP address and the prefix http://.
To load a page enter, for example
http://192.168.10.71
The following web site appears:
Use a standard patch cable to connect the device to a
switch, hub or router of the IP network. You can also use
a WLAN access point as network coupler. This means
you can commission the DALI via a portable note book,
tablet PC or mobile phone.
Use the log-in-page to assign either ‘User‘ or ‘Administrator‘ rights to a user. User rights mean that the website
functions are restricted and configuration commands are
disabled. Use this login if you would like to use the website only for visualisation and operational purposes. To
commission the DALI via the website administrator rights
are required. The images and descriptions below are all
based on the administrator display. Different passwords
for user and administrator can be set in the ETS. The default setting for both users is ‘0‘.
Log in as administrator to access the following configuration website:
Once the network is physically connected, you need to
assign an IP address to the gateway to enable access via
the web browser. By default, all IPAS devices with an IP
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 12 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
Configuration buttons
ECGs
Groups
Information and status
area
Change web sites
6.1 Configuration buttons
The icons in the website header are used for the different
commissioning functions. They have the following meaning:
Refresh
The configuration page is divided into different sections.
The section at the top of the page contains the configuration buttons that are required for the commissioning
(some of these buttons are only visible if you log in as
administrator). The fields underneath the configuration
buttons are for the 16 group and 64 ECG functions. The
bottom section contains the information and status area.
The three tabs in the footer are used to change from
general configuration to scene configuration and effect
configuration.
All operable buttons work with tool tips. This means a
function description appears if the cursor hovers over the
button.
This function refreshes the website content. On principle,
the website is static. This means that the details on the
page are only updated when the site is first loaded. Any
faults or changes that are not made on the website itself,
such as a light status adjustment via a KNX telegram are
not automatically displayed.
New Installation
Press this button to start a new installation (reset and
teach-in process) of the connected DALI line.
|
During a new installation any previously existing
configurations of the DALI line are deleted.
Post-installation
Press this button to start a post-installation within the
DALI line. Any ECGs that no longer exist are deleted during the post-installation process. At the same time new
devices are added.
ECG Quick Exchange
Press this button to start an ECG easy replacement
within the DALI line. The easy replacement is only possible when a single faulty ECG is replaced by a new one.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 13 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
ECG / group blink-mode
Device status
Press this button to display the device status of the
gateway in the information and status area at the bottom
of the page. Click on a group or ECG field to display the
status information of the selected ECG or group.
Broadcast On
Broadcast Off
Broadcast Blink
Use these functions to simultaneously switch all ECG
lights /lamps in the DALI line off or on or set them to
blink-mode via a DALI Broadcast telegram.
6.2 Control buttons
There are further control buttons above the ECG field.
These are used to perform ECG or group specific operations. To carry out one of the operations, you must select
the operation first and then click on the group or ECG
concerned. The selected function appears in a white
frame. Press the button again to cancel the selection.
No selection
First button selected
The individual buttons have the following meaning:
Delete assignment
Use this button to delete the assignment of an ECG. Select the button first. Then click on the ECG. If the ECG
was assigned to a group, the group assignment is deleted. If the ECG was marked for individual control, it is
now marked as ’not in use‘.
Assign a group
Use this button to assign an ECG to a group. First select
the button. Then click on the group. To complete the
process click on the ECG you want to assign to the
group. If the ECG was previously assigned to a group,
the previous assignment is automatically removed.
Select ECGs for individual control
Use this button to enable an ECG for individual control.
ECGs that were found during the search process first
appear with a question mark. This means that they are
considered to be ‘not in use’. If you want to enable an
ECG for individual control, select the button and then
click on the ECG concerned. The ECG is marked with
the letter ‘S‘ (Single) and is now in use.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Use this button to set an individual ECG or a group to
blink-mode. To carry out this function, select the button
first. If you now press an ECG or group field, the corresponding ECGs/lamps start blinking. The blink-mode is
used for identification purposes during the DALI commissioning process. If you press the same ECG or group
field again, the blinking stops. If you press another ECG
or group field with the button still selected, this element
starts blinking and the previously blinking lamp is turned
off.
Toggle light value
Use this button to switch the value of a group on or off.
First select the button. Then click on a group field to toggle between the light values of all lamps assigned to the
group. The same process applies to ECGs.
Swap ECG short addresses
Use this button to swap the position and thereby the
short address of two different ECGs. First select the button. Now click on two ECG fields one after the other to
physically swap their short addresses and adjust their
position in the list. This function is required to sort the
random ECGS into a specific order after a new installation.
|
You should only use this function directly after a
new installation. Later use should be avoided as
the parameters set in the ETS are not swapped
in line with the addresses.
6.3 ECG fields
The ECG and group entries on the website mean that the
user can see the complete function and failure status of a
connected DALI line at a glance. The ECG fields are
numbered from 1 – 64. The number is shown in the bottom left-hand corner of the field and corresponds to the
ECG short address within the DALI line. If an ECG is
found during the search process (new and postinstallation), a lamp or battery icon is inserted in the field.
The battery icon symbolises an ECG for self-contained
battery emergency lights (device type 1). All other device
types (without battery) are shown with a lamp symbol. If
in the ETS an ECG is configured as emergency luminaire
with central battery, a separate icon is displayed. The following icons are available:
ECG
ECG for self-contained battery emergency lamp
non-switchable
ECG for self-contained battery emergency lamp
switchable
Seite 14 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
ECG with central battery supply
The value and failure status of an ECG is symbolised by
different icon and background colours.
6.5 Information and status fields
The bottom section of the configuration website shows
status information for the device as a whole or for a selected group or ECG.
ICON light grey => Lamp switched off
ICON yellow => Lamp switched on
ICON red => Lamp failure
Red background => ECG failure
The assignment of an ECG is also shown in the field.
Newly found devices are marked as ‘not assigned‘ via a
‘?’ symbol above the icon. When an ECG is assigned to
a group, the group number replaces the ‘?’ symbol. If an
ECG is used for individual control, it is marked with the
letter ‘S‘ (Single).
When the website is first loaded, the status information
always applies to the whole device giving you the opportunity to see the number of connected lamps, ECGs and
converters, as well as failures and failure rate at a
glance. The green colour means that no fault has occurred. Otherwise the colour changes to red.
This information can be displayed at any time by pressing
the device status button in the configuration bar at the
top of the site.
ECG not in use
ECG in use for individual control
To display the status information of a group, click on one
of the 16 group fields.
ECG with group assignment (e.g. group 3)
6.4 Group fields
As for the ECG fields, the group fields show the status of
a group. However, the display is limited to the switch
status. No failure status is graphically displayed.
ICON light grey => group switched off
ICON yellow => group switched on
If a group or ECG is switched via the website, its status is
automatically updated and displayed on the site. However, if the switch command was initiated externally via a
KNX telegram, the status is not automatically updated.
To display the correct status, press the refresh button or
re-load the web page.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
In addition to the number of devices and converters and
the individual failure types, the total failure rate is shown.
Please remember that the rate is calculated as a percentage of the total number of ECGs and converters in
the group. Use the Name field to enter a user-friendly
name for the group. The maximum number of characters
is 10. Press the √-button to confirm your entry. The name
is now saved on the gateway and loaded into the ETS
during the next synchronisation.
To display the status information of an ECG, click on one
of the 64 ECG fields. Choose from one of the following
options: General, Run Hours, Burn-in and Test
Seite 15 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
Use the name field on the General page to enter a userfriendly name for the ECG. The maximum number of
characters is again 10. Press the √-button to confirm your
entry. The name is now saved on the gateway and
loaded into the ETS during the next synchronisation.
The maximum burn-in time that was configured in the
ETS and the already completed burn-in time are also
displayed.
If the selected ECG is a device for self-contained battery
emergency lights, you can also click on the Test tab.
An ICON appears behind the word Alarm if a fault or
alarm has occurred. The meaning of the icons is as follows:
Lamp failure
ECG failure
Converter failure
Life cycle exceeded
An ICON appears behind the word Mode if the ECG is
not in normal mode. The meaning of the icons is as follows:
Permanent mode
Panic mode
This display shows the type of test, test result and date
and time of the last test. The status bar shows the failure
flags. A green bar means that the test was positive. A red
bar signals a negative test result.
You can use the buttons on this page to manually start a
test (Execute Test). The icons underneath have the following meaning:
Battery Test
Central battery test mode
Functional Test
Burn-in mode
Long Duration Test
Update test result
Please remember that the website is static and is not
automatically updated after the test has finished. If you
would like to display the result of a manually activated
test, please press the ’Update test result’ button first.
Click on the Run Hours tab in the header to see the accumulated operating hours of a lamp since its last reset
as well as the maximum life span that was configured in
the ETS. Use the button on the right to reset the counter
to 0.
Click on the Burn-in tab in the header to start and stop
the burn-in mode for the selected ECG.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 16 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
7. ETS special and commissioning
functions
As previously described in chapter 4, you can choose eiher type A ‘Normal mode‘ or type B ‘Extended mode‘ for
the DALI commissioning. Depending on the mode you
choose, different special functions and pages are available in the ETS.
7.1 Special functions in ‘Normal mode‘
7.1.1 Synchronisation with the connected
DALI line
When you first load the parameter page, the parameters
and groups for all possible 64 ECGs and 16 groups are
displayed. In ETS mode A it is possible to simplify the
commissioning and to bring the application in line with
the real conditions of the connected DALI line. To do so,
you need to synchronise the application with the installation first.
Start the synchronisation via the sync button in the bottom right-hand corner of the main window. Depending on
the size of the installation the synchronisation may take a
few seconds. A bar at the bottom of the page shows how
far the synchronisation has progressed. When the synchronisation is complete, only the objects and parameters of those ECGs that are physically connected to the
device are shown.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
In addition, the device types and, if applicable, the group
assignments are also automatically set.
If during the synchronisation a device type is found that
does not match with the current settings in the ETS, a
warning message appears. Please acknowledge the
message by pressing yes or no.
By default the synchronisation of the ETS is performed
via the KNX network. If the gateway is already correctly
integrated into the IP network and a corresponding IP
address has been assigned, the synchronisation can also
be performed via Ethernet. In this case, all you need to
do is enter the correct IP address of the device into the
tool bar at the top of the window and tick the check-box in
front of the bar. Alternatively, you can press the Read IP
Address button to set the IP address of the selected device without manual entry.
Seite 17 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
The synchronisation compares the application to the data
of the connected DALI line.
|
This means that you should always synchronise
when you change the system structure or expand the system.
7.1.2 User-friendly names for ECGs and
groups
To make the configuration as easy as possible for the
user, it makes sense to choose user-friendly names for
ECGs and groups. Any names need to be assigned on
the website in ETS Mode A directly during the identification. Please remember to press the confirm button next
to the entry field after entering a name.
Use the ‘Load Description’ command in the Tools menu
to load the names directly into the ETS. The names are
shown in brackets next to the corresponding device.
As loading the names via KNX can take quite some time,
you should use the Ethernet connection for this process.
Before starting the process, please make sure you set
the right IP address and tick the check-box in front of the
address.
7.2 Special functions in ‘Extended
Mode‘
If you select ‘extended Mode‘ (Mode B) for the DALI
commissioning (see chapter 4), an additional menu appears underneath the main menu bar with the entries
’Parameter‘, ’Commissioning‘, ’Scenes‘ and ’Effects‘
Use the menu item ‘Parameter‘ to set the ETS parameters in the same way as in mode A. However, please remember that in mode B all parameters are visible because the parameter settings can be performed independently of the actual system. Simplifying the parameters and objects by synchronising with the system is not
possible in this mode.
The menu item ‘Commissioning‘ is described in more detail in the next chapter. For a description of menu items
‘Scenes‘ and ‘Effects‘, please see chapter 11.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 18 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
7.2.1 Preparing and planning the DALI
commissioning in ‘Extended Mode‘
In Mode B, the menu item ‘Commissioning‘ opens an additional page which is not available in ‘normal mode‘. This
page is used both to plan the installation in advance of
the commissioning and to perform the actual DALI commissioning later on (identification and assignment of
ECGs).
The structure of the commissioning page is as follows:
The group configuration is displayed on the left-hand side
in a tree structure. The area in the middle shows the
ECG configuration and names in a table format. On the
right hand side is a list of all devices found in the system,
which have not yet been identified. During the planning
stage this part is empty as the ETS is not yet connected
to the system.
To start with you should plan and name the ECGs. Use
the description field in the ECG configuration to enter a
name (light number, room number, etc.)
The maximum number of characters available for names
in the ETS plug-in is 30. Whilst, in principle, the names
are also transferred to the device website, it is important
to remember that the website will display no more than
the first ten characters of the name entered in the plugin.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
If you confirm your entry with the return button, the cursor
automatically jumps to the next ECG field. This makes
the naming process easy and secure.
Once you have planned the ECGS, you should assign
the groups. There are two ways to assign groups via
drag-and-drop:

Use the mouse to select an ECG in the ECG configuration field in the middle and drag it to the left dropping it above the required group in the group tree.

Use the mouse to select an ECG from the group directory’s top category ‘not assigned‘ and move it
down the directory dropping it above the required
group.
Once an ECG has been assigned to a group via drag
and drop, the group number is automatically displayed in
the ‘group number‘ field of the ECG configuration table.
You can enter a user-friendly name for the group in the
‘group description‘ field. ECG and group names are
automatically shown in the group configuration directory
(displayed in brackets) as well as in the description of the
ETS communications objects. Having user-friendly
names makes linking the group addresses with the communications objects much easier for the system integrator.
As soon as an ECG has been assigned to a group, it is
no longer available for individual control. The parameters
and communication objects are adjusted accordingly following the group assignment. ECGs that have not been
assigned to a group are automatically regarded as ECGs
for individual control.
Please see chapter 11 for the planning and setting of
scenes and effects.
Seite 19 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
7.2.2 DALI commissioning in ‘Extended
Mode‘
Once the planning, parameter setting and linking of
group addresses have all been completed the DALI line
can be commissioned. To do so, please connect the
commissioning PC with the ETS to the KNX system via
an interface (RS-232, USB or IP). Once the connection is
active, you need to program the physical address of the
gateway. The communication between the plug-in and
the gateway is based on the physical address (or possibly on the IP address, see below).
Use the ‘commissioning‘ page and the ‘tools‘ menu to
start the teach-in process of the connected DALI line.
Please remember that the selection shown above is only
visible in the ‘Tools‘ menu if you have selected the
‘commissioning‘ page. The elements displayed always
depend on the setting selected in the menu bar.
During the teach-in process all ECGs are automatically
recognised and each ECG is assigned a short address
from 0 - 63. Depending on the size of the connected
DALI line the process can take up to 3 minutes.
A bar in the bottom right hand corner indicates how far
this process has progressed. The number of ECGs that
have so far been found is also shown (in brackets).
You can now identify the devices by switching the corresponding lamp on or off. If you select an ECG and press
the right mouse button, a context menu appears from
which you can select the required function.
Alternatively, you can also tick the box ‘Automatic blink
mode‘. In this case, the blink mode starts by itself when a
device is selected. The context menu is also available at
group and gateway level. During the identification process it might be useful to switch certain groups or all connected lamps on or off. If you select the main item ‘group
configuration‘, you can use the right mouse button to
send broadcast commands for on, off and blinking.
Once an ECG has been identified, you can drag and
drop it onto the previously planned element in the ECG
configuration table.
Once the teach-in process is complete, all ECGs that
have been found are displayed in the list of non-identified
devices on the right-hand side.
Once an ECG has been dragged into the ECG configuration table, it disappears from the list of non-identified
ECGs. The ‘PLAN‘ flag in the configuration table shows
that the ECG has been assigned to the planned element.
If an ECG has been wrongly assigned, it can be moved
back to the list of non-identified devices using the same
drag & drop mechanism.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 20 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
After the ECG has been moved back, the element in the
configuration table is empty (Flag: ‘PLAN (E)‘  Empty)
and the ECG re-appears in the list of non-identified devices from where it can now be moved to a different element if required.
Please remember that at this point all operations that
have been performed are only displayed in the work
space. They are not immediately loaded onto the DALI
gateway. To start the process of downloading the settings onto the gateway and the ECGs, you must press
the ‘Download DALI‘ button. The download can take up
to 2 minutes. The progress bar informs about the current
status.
7.2.3 ECG and lamp faults during DALI
commissioning in ‘Extended Mode‘
During the commissioning lamps/ECGs are identified
visually (ON, OFF, blinking). It is therefore crucial that all
lamps and ECGS operate correctly. If the gateway identifies a lamp or ECG fault during the installation process,
the ECG concerned is highlighted in a different colour. A
red flag indicates an ECG fault and a yellow flag a lamp
fault.
Once the download is complete, all previously planned
ECGs are programmed in the real system with the DALI
configuration. The respective devices are marked with an
‘OK‘ flag in the ECG configuration table.
Faults are displayed both for non-identified devices (right
table) and for ECGs that have already been assigned
(middle table). As the table view is not automatically updated and as it may take a few minutes for the DALI
gateway to recognise a fault, we recommend that you
press the ‘Sync‘ button a short while after the installation.
This ensures that the displayed status corresponds to the
actual status and any faults that may have been detected
in the meantime are displayed correctly.
Non-identified devices remain in the list on the right-hand
side.
|
Please remember that the download on the
‘commissioning page‘ only programmes the
DALI configuration data onto the gateway and
ECGs. Fol-lowing the DALI identification and
commissioning the actual ETS application with
parameter settings and group addresses still has
to be downloaded onto the device.
Attention: If an ECG fault already exists during the
search process of the initial installation, the device may
not be detected at all. This means that the number of
ECGs found does not correspond to the number that was
expected. ECG faults are only displayed in the manner
described above if the ECG concerned has been previously programmed and is known to the gateway.
After leaving the parameter page, this is done via the
usual ETS download process.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 21 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
7.2.4 Using dummy ECGs in ‘Extended
Mode‘
There may be cases in which a DALI installation or a
DALI line needs to be commissioned even if not all of the
planned lights are yet physically present (e.g. if a room is
not yet finished or a light has not been delivered). During
the teach-in process only the actually existing devices
are detected and entered into the list of non-identified
devices. This means that only those devices can be
moved into the configuration table and commissioned as
a real device. Entries for devices that are planned but do
not yet exist remain empty in the configuration table.
These devices can be programmed, identified and assigned later on during a post-installation (see below)
once the whole installation is complete.
As long as an entry remains empty, the gateway assumes that no ECG exists and does not generate an error message. However, it may be desirable that an error
message for a planned device is generated, even if the
device is not yet present (for example to visualise an incomplete installation).
The plug-in offers the possibility to add dummy ECGs to
the list of non-identified devices. This special option is
not set up by default. To use this option, please go to
‘Tools‘  ‘Options‘ to activate it.
and therefore presents an ECG fault in the visualisation
and the respective communication object.
ECGs that have been created through a dummy entry
are shown with a grey background in the ECG configuration list (see above).
The dummy ECGs are only used as a temporary solution
in an unfinished installation. The ‘post-installation‘ that is
required once the whole installation is complete, deletes
all dummy entries from both the ECG configuration table
and from the list of non-identified devices.
7.3 General extra functions in the ETS
The functions described in the following chapters can be
used both in ‘Normal Mode‘ and in ‘Extended Mode‘.
7.3.1 Using IP for plug-in communication
Once
it
has
been
activated,
an
additional
‘Dummy+‘button appears in the parameter window.
By default, the plug-in communicates with the DALI
gateways via the KNX-Bus. However, if the gateway is integrated into an IP network and a correct IP address has
been assigned (DHCP or fixed setting in the ETS) IP
communication can also be used. This increases the
speed of loading and communication processes greatly.
To use IP communication, enter the correct IP address of
the gateway in the IP field at the top and tick the box in
front of the field.
You can also import the IP address via the ‘Read IP Address‘ button. If you press the button, the correct IP address of the current device is automatically entered in the
address field.
Use this button to add dummy ECGs to the list of nonidentified ECGs.
Dummy ECGs are marked with a
symbol and can be
dragged into the ECG configuration in the same way as
normal ECGs. Once the DALI data has been
downloaded, the gateway assumes that an ECG exists
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
|
Please remember that when IP communication
is en-abled (by ticking the box), the plug-in
communicates with the gateway always via the
address entered. A wrong manual entry may
lead to a wrong gateway being contacted. Therefore please make sure that the IP address is correct.
Seite 22 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
If the IP communications box is ticked but an IP connection is not possible (wrong IP address, no network connection), the plug-in will still try to make the connection
via IP. However, it recognises by itself that this is not
possible and automatically changes to KNX communication.
IP communication can be used both in ‘Normal Mode‘
and ‘Extended Mode‘.
7.3.2 Parameter templates
The gateway gives you the possibility to create your own
parameter templates thereby making the time-consuming
parameter setting for individual groups or ECGs much
easier. Parameter templates can be generated for all parameters of the entire gateway and for individual ECGs
and groups. Once you have completely set the parameters for a standard ECG, simply press the Export function
in the Files menu or click on the right mouse button to
export them as an xml file.
If you would like another ECG to have the same parameter properties, simply select the ECG and import the exported file into the new ECG. The file serves as a template for other ECGs. You can also create templates at
group level or for ‘General Properties‘. Creating templates for all ECG and group types and using this template library makes the configuration, especially in large
installations, significantly easier.
7.3.3 DALI configuration data back-up
The configuration data and parameters set in the ETS
are automatically saved in the ETS database after each
change. They can be easily downloaded onto a new device at any time. However, the DALI configuration data,
such as the DALI long address, is not part of the normal
ETS application. To back-up the DALI configuration data,
please use the back-up function in the Files menu.
The backup function exports the current real configuration from the gateway and saves it as an xml file.
|
The DALI configuration data in the ETS is also
updated during a back-up. Any changes that
were made in the ETS but that have not yet
been down-loaded onto the gateway (planning
only), are therefore overwritten during a back-up.
If you need to exchange a device, you can load the
backed-up data onto a new device via Restore. Backup –
Restore gives you the opportunity of a simple device exchange without the time-consuming post-installation. We
therefore strongly recommend that you create a back-up
and save the data after completing the parameter settings.
If you would like to re-set individual ECG or group parameters or even a whole gateway to their original status,
please use the files that have been provided with the
product:

default_device.xml

default_ecg.xml

default_group.xml
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 23 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
8. DALI maintenance and expansion
8.1 Quick exchange of individual ECGs
When a DALI line is commissioned, the short address,
group assignment (if applicable) and other configuration
data are programmed onto the ECG’s internal memory. If
you had to replace an ECG because of a fault, you would
normally need to program this data onto the new device.
The gateway, however, offers a function that makes it
possible to quickly and easily replace individual ECGs.
You can start the “ECG easy replacement“ function either
on the device itself (push buttons, display) or via the web
browser if you log in as administrator (see above). The
gateway first checks if any of the configured ECGs that
are known to it have been reported as faulty. Then the
line is searched for new, unknown devices. If a new device is found, all configuration details of the old ECG are
automatically programmed onto the new one and the installation is immediately ready for operation.
However, the ECG easy replacement only works if just
one ECG within a line is faulty and replaced by a new
one. If several devices are faulty, the ECGs have to be
identified and you must use the post-installation function.
Please also remember that the easy replacement is only
possible for devices of the same type. You cannot, for
example, replace an ECG for self-contained battery
emergency lamps with a device for LEDs.
If a quick replacement is not possible, the gateway terminates the process with an error code. The different error
codes have the following meaning:
Error type 7:
Error type 8:
Error type 9:
Error type 10:
Error type 11:
No ECG failure
More than one ECG failure
No new ECG can be found
ECG has wrong device type
More than one new ECG
8.2 Extending the existing system –
post-installation
If you would like to enlarge an already commissioned
DALI line with new ECGs or would like to replace several
faulty ones, please use the „post-installation“ function.
You can carry out the post-installation both on the device
(push buttons, display) and via the web browser if you log
in as administrator (see above).
If you use the ETS in ‘Extended Mode‘ (Mode B), you
can also load the post-installation in the ETS via the
menu ’Tool‘  ’post-installation’.
When you start the installation, the gateway first checks if
all previously configured ECGs are still available in the
line. ECGs that no longer exist or cannot be found are
deleted from the gateway’s internal memory. Then the
line is searched for new ECGs. Newly found devices are
inserted into any existing gaps or added on at the end.
|
Please remember that the maximum number of
ECGs within a line is 64!)
As the position (short address) of a newly found device is
allocated randomly, you need to identify the lights and if
required assign them to groups.
If you are using the ETS in ‘Normal Mode‘, you need to
re-synchronise the ETS so that communication objects
and parameters for the newly added ECGs are shown
and the configuration can be completed.
However, synchronising the ETS is only necessary if the
structure of the line has been changed by the postinstallation process (enlargement of the system or different device types). If the purpose of the post-installation
was merely re-configuration after an ECG replacement,
synchronisation is not required.
In the ETS setting ‘Extended Mode‘ all parameters and
objects are visible. This means that you only need to
identify and assign the devices that were newly found
during the post-installation followed by a DALI download
and possibly an ETS application download.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 24 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
9. Different operating modes
the group remains at the currently set value. If the mode
is enabled again, the timer starts again from the beginning.
9.1 Normal mode
In normal mode, ECGs can be dimmed and switched
without restrictions both via individual and group control.
The control of each ECG and each group is based on
three communication objects (switching, dimming, value
setting).
Please remember that ECGs, once they have been assigned to a group, are no longer available for individual
control. An ECG can only be assigned to a single DALI
group. The gateway does not support multi-group assignments on DALI level. If such assignment is required,
please use KNX communication objects for this purpose.
At group level, an additional enable/disable object is
available to disable the control via the three communication objects.
Separate status objects inform about the switch and
value status both at group and individual ECG level.
9.2 Permanent mode
If you would like to run an individual ECG or a whole
group permanently with a certain light value, (e.g. a permanently lit corridor or workshop) you can choose the
permanent mode option. The ECG or group are automatically set to the required value after you program or
switch on the gateway. Switch and dim objects remain
hidden. Light status, error and service functions, however, are also available in permanent mode.
|
Should a device in this mode not be running at
the pre-set light level because of a special operation (e.g. identification process on the device
display) or fault (e.g. ECG was without power
when the gateway was started) the light level is
automatically corrected after 60 seconds.
9.3 Staircase mode
The staircase mode is only available for groups. In this
mode, the value set via a switch, dim or value telegram is
automatically changed to the switch off value after a programmable time. The lights can be switched off immediately or in 2 steps (within a minute) or through dim-down
(within a minute).
In staircase mode, each additionally received telegram
re-starts the internal timer. The lights switch off when the
timer runs out after the most recently received telegram.
The staircase mode can be disabled or enabled via an
additional object. If the staircase mode is disabled, the
group behaves like in normal mode and does not automatically switch off. If the mode is disabled whilst the
switch-off timer is already running, the timer stops and
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
9.4 Night Mode
Night mode is available both at group and ECG level.
The night-time mode corresponds largely to the staircase
mode. The only difference is that the automatic switch-off
is dependent on the central night object of the gateway. If
the night object is not set (day), the group behaves as in
normal mode. If the object is set (night), the ECG or
group either switches off after a programmable time or it
goes into permanent mode.
9.5 Panic / Emergency mode
The panic or emergency mode can be activated via a
central object for the whole gateway. All ECGs/ groups
that have been enabled for panic mode, permanently
switch to a programmable panic light value on receipt of
the object. They can no longer be controlled individually.
When the panic mode is switched off, the devices return
to the previous light value or the switch on / switch off
value and can again be controlled individually.
9.6 Test mode for central battery emergency luminaires
Through its internal function the gateway supports installations with central battery emergency luminaires. Any
ECG (except for those of the self-contained battery type)
can be configured as an emergency light. You can
choose a test time between 15 minutes and 4 hours. If
the gateway receives the central battery test object, the
respective lights change to a programmable value for this
time period. They can no longer be switched or dimmed
via the corresponding objects. The discharge time and
capacity of the central battery can thereby be tested under pre-defined conditions.
So that individual ECGs within a group can no longer be
switched via group telegrams or scenes, the group assignment is dissolved for the duration of the test mode.
When the test has finished, groups and scenes are
automatically re-programmed onto the ECGs. Should the
gateway lose power during the test mode, the unprogrammed devices are marked and automatically programmed on return of the power supply. The test mode,
however, does not continue. It has to be re-started.
When the test mode terminates normally, the devices return to the previous light value or the switch on / switch
off value and can again be controlled individually.
Seite 25 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
9.7 Burn-in mode
9.8 Operating mode hierarchy
For optimum operation and to achieve the quoted life
span, many lights require that a specific burn-in time be
adhered to during their first use. During the burn-in phase
lights must not be switched or dimmed but need to run
continually at 100% capacity. This burn-in phase can be
carried out automatically with the gateway. Each ECG
can be individually set to the burn-in mode via a further
object. During the burn-in, switch and dim telegrams for
the device are ignored. This also applies when the ECG
is assigned to a group. So that individual ECGs within a
group can no longer be switched via group telegrams or
scenes, the group assignment is dissolved for the duration of the burn-in mode. When the burn-in has finished,
groups and scenes are automatically re-programmed
onto the ECGs. Should the gateway lose power during
burn-in mode, the un-programmed devices are marked
and automatically programmed on return of the power
supply. The burn-in mode, however, does not continue. It
has to be re-started. When the burn-in mode finishes
normally, the devices return to the previous light value or
the switch on / switch off value and can again be controlled individually.
Some of the individual operating modes described above
have higher functions and roles for the operation of the
system as a whole. A prioritisation or hierarchy of operating modes is therefore required. The burn-in mode has
the highest priority. If an ECG is in burn-in mode, it cannot be changed into any other mode. The next hierarchy
level is the central battery test mode. If the device is in
this mode, it can only go into burn-in mode but not into
any subordinate operating modes. Below the test mode is
the panic/emergency mode. From this mode the device
can change to both the burn-in mode and the test mode.
The permanent, normal and night-time modes have the
same priority level at the bottom of the hierarchy.
The burn-in mode is usually started manually after each
light change. This useful maintenance function can be
operated via the device display to ensure that it can be
performed by maintenance personnel independent of the
ETS or KNX. Alternatively a burn-in start is also possible
via the integrated web server.
Burn In Mode (Value fix = 100%)
Test Mode Central Battery (Value fix = 1 … 100 %)
Emergency / Panic Mode (Value fix = 1 … 100 %)
Permanent
Mode
(Value fix =
1 … 100 %)
Normal Mode
(Value variable)

Night Mode
(Value variable
with ΔT or fix =
1 … 100 %)
Start / Stop
Burn-In
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 26 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
10. Analysis and service functions
10.1 Recording operating hours
The gateway allows for the operating hours (burning
time) of each lamp to be internally recorded to the second. The value is available externally (communication objects, web site, display on the device) in hours with the internal value in seconds always being rounded. (e.g. 7199
seconds  1 h, 7201 seconds  2h) The recording of
operating hours is independent of the dim value. This
means any light value > 0% contributes to an increase in
the operating hours. The counter can be re-set (when the
light is changed). To reset the counter, the value 0 is written on the communication object or alternatively use the
website or the display and push buttons on the device.
A maximum value can be configured for each ECG (light
life span), which activates an alarm object on the KNX
bus or an entry on the website. This information can be
used for maintenance purposes.
10.2 Individual fault recognition at ECG
level
A major advantage of DALI technology is the individual
recognition of light failure or ECG failure. The gateway
supports this function completely and also offers numerous analytical possibilities.
For the analysis, the Dali gateway scans all connected
ECGs periodically for ECG, light and (in the case of selfcontained battery lamps) converter failures. The scanning time can be configured. If the time is 1 second
(standard setting), and 64 ECGs are connected, the
complete process of scanning for ECG and light failure
takes 128 seconds (1 second per ECG and type of failure). It can therefore take up to about 2 minutes before a
fault that has occurred is recognised. For each ECG a
communication object is available to send the information
to the KNX bus (1Bit or 1 Byte object).
In addition, the failure status of all ECGs is displayed
clearly on the gateway’s website.
You can also request the failure status of all individual
ECGs, converters and lamps via a special failure status
object (object number 20, see communication object description below).
An ECG field with a red background on the website indicates an ECG (or converter) failure. A red lamp symbol
indicates a light failure. If you select the respective ECG,
the individual failure status is available in the status and
information section at the bottom of the website.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 27 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
10.3 Fault analysis at group level
10.4 Fault analysis at device level
If ECGs and / or converters are merged into groups, numerous group-specific fault data is available in addition to
the (also still available) individual ECG data. For this purpose three different communication objects are available
for each group. In addition to general information such as
whether there is a failure within a group and of what type,
the complete number of faulty devices within the group
and the failure rate can be listed via a communication object. An alarm object is sent when a certain failure rate is
exceeded. A complex object with a summary of the data
further adds to the analysis options.
For details of group-specific communication objects,
please see the communication objects description below.
Fault analysis objects similar to those at group level are
also available at device level (i.e. for all ECGs connected
to the gateway). The failure rate or number of ECG failures in the whole DALI line can be made available via
communication objects. Unlike at group level, at device
level the percentage and number of failures can be broken down further according to type of failure. The alarm
threshold for the failure rate can be individually set for
ECG, light and converter failure. For further details regarding the communication objects, please see the
communication objects description below.
As before, the fault information for the entire gateway is
displayed on the web site:
The group information is also displayed on the web site
of the integrated web server:
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 28 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
11. Scenes and effects
11.1 The scenes module
11.1.1 Scene programming via the scene
website
For full and easy scene programming, use the website of
the server which can be accessed via the scene tab at
the bottom:
The gateway enables the programming and invoking of
up to 16 internal light scenes. A scene is invoke via a
1Byte scene object. This object can also be used to save
scenes (Bit 7 set). The currently set value is saved as
scene value.
In principle, a scene can consist of group and individual
ECGs (as long as these have not been assigned to a
group).
To assign a group to a scene or to delete a group from a
scene, use the push buttons and display on the device or
the website. If you are using the ETS in ‘extended Mode‘,
you can also set and assign scenes via ETS. You cannot
assign individual ECGs to scenes only by using the
pushbuttons and display.
By default, the programmed scene is started immediately
without dim time. If you want to dim into a scene, you can
set a dim time for each scene. The time can only be set
on the website. Please remember that the entry refers to
the dim time from 0 to 100%. If invoking a scene leads to
a change from 50% to 100% with a set time of 20 seconds, the dimming process takes only 10 seconds.
Switching an individual group (or ECG) from the scene
whilst a scene is already in the dimming process, only affects the particular group. The other groups continue the
dimming process.
Please remember to use the DALI command for scene
addressing only when you invoke a scene without dimming. Dimmed scenes must be started at DALI level via
short or group addresses. Scenes that have been assigned a large number of groups or ECGs should therefore be used without dim time to prevent irregular dimming.
Scene Tab
To program a scene, select it first from the scene block at
the bottom of the page. (If the scene has been previously
programmed, the corresponding light value appears).
Once you have selected a scene, you can use the assignment button to add or remove groups or individual
ECGs to and from the scene. Click on the button first and
then on the group or ECG. For already assigned groups
or ECGs, the fields are highlighted in yellow and the dim
value is displayed in percentages.
You can only use individual ECGs in scenes if they have
not been assigned to a group.
Use the programming buttons to change the light value.
The buttons have the following meaning:
On switching
Off switching
Up dimming
Down dimming
As before, select the required programming button first
and then the group or ECG. The dim values can only be
changed in increments. The increment size varies ac-
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 29 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
cording to the logarithmic dimming curve of the DALI
ECG.
You may also set the dim time and program a specific
name for the selected scene. Use the programming button to save the set values on the gateway and ECG.
In principal you can also use ETS to plan individual
scenes ‘offline‘, independently of the DALI system. The
plug-in only has to be connected to the gateway for the
duration of the download.
11.2 The effect module
Scene programming
Please remember that the set values are only saved if
you press the button. If you change to another scene
without saving, any changes you made are lost.
11.1.2 Scene programming via ETS in ‘Extended Mode‘
If you are using ETS in ‘extended Mode‘ (Mode B), you
can program and assign scenes in ETS.
In addition to light scenes, the gateway also allows for
the use of effects. An effect is a sequence control of light
values in different groups or ECGs. The individual light
values can be triggered immediately or dimmed via a dim
value. Please remember that the entry relates to a dim
time from 0 to 100% (see scene module above). With the
gateway you can create 16 independent effects. A 1 Byte
object is used to start and stop an effect. To start an effect, set Bit 7 in the object. If the object is received with
Bit 7 being deleted, the effect stops. Altogether 500 effect
steps can be programmed. They can be distributed arbitrarily across the 16 effects. A delay can also be programmed as an effect step.
11.2.1 Effect programming using the effects website
You can set and program effects via the server website
which can be accessed via the effect tab at the bottom of
the site:
Go to the scenes page and select the required scene
from the directory on the left-hand side. Move the groups
and individual ECGs which you would like to use for this
scene from the directory on the right-hand side into the
field in the middle using drag-and-drop. Use the value
fields to enter the light value for this scene.
You can enter a user-friendly name for each scene in the
description field underneath the scenes. If you do not
want a scene to start immediately but would prefer dimming it up to its final value (see above), you can set the
dimming time individually for each scene.
Effect Tab
Once all scene values have been set and assigned, you
need to download the scene onto the DALI gateway. For
this purpose, please press the download button in the
bottom right-hand corner.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
To program an effect, select it first from the effect block
at the bottom of the page. (If the effect has been previously programmed, the corresponding effect steps are
displayed in the Effect Editor on the right hand side of the
page.)
Use the function buttons in the Effect Editor to add or
remove steps or delays. You can select the target group
Seite 30 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
or individual ECG for each step as well as the final dim
value and delay from the drop down menus. If you insert
a delay as an effect step, the effect control will pause until the next step is executed. You can thereby create a list
with the entire sequence control for each effect. . Each
step can also be repeated in a continuous loop. To do so,
please tick the Effect loop mode box above the list. If an
effect runs in continuous mode, it is repeated until it is
stopped either via the communication object or by pressing a button on the website.
11.2.2 Effect programming via ETS in ‘Extended Mode‘
If you are using ETS in ‘extended Mode‘ (Mode B), you
can program effects in ETS.
The individual buttons have the following functions:
Add delay
Add effect step
Move effect step up
Move effect step down
Delete effect step
Go to the Effects page and select the required effect from
the directory on the left-hand side. Move the groups and
individual ECGs which are needed for this effect from the
directory on the right-hand side into the field in the middle
using drag-and-drop. The order of the entries corresponds to the order of the individual effect steps. You
can also use drag-and-drop to move the delay times into
the table and to change the order of items within the list.
When the list is complete, load it onto the device.
Effect programming
Please remember that the set values are only saved if
you press the button. If you change to another effect
without saving, any changes you made are lost.
Use the Start and Stop buttons to activate and test the
selected effect directly from the page.
Export effect list
Start effect
Stop effect
Program effect
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Use the fields ‘Value‘ and ‘Time‘ to set the final value to
which you would like to dim a group or ECG as well as
the dimming time for each effect step. If you are setting a
delay, the entry in the ‘Time‘ colum shows the length of
the delay. Use the descriptions field underneath the effect steps to enter a user-friendly name for each effect.
Tick the ‘Repeating‘ box if you would like the selected effect to run continuously.
Once the table of effect steps is complete, you need to
download the effect onto the DALI gateway. For this purpose, please press the download button in the bottom
right-hand corner.
In principal you can also use ETS to plan individual effects ‘offline‘, independently of the DALI system. The
plug-in only has to be connected to the gateway for the
duration of the download.
Seite 31 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
12. Self-contained battery emergency
lamps
The gateway supports control gears used to run selfcontained battery emergency lights (device type 1 in accordance with EN 62386-202). Such devices contain a
battery which can supply the light with power in case of a
general power failure.
To identify the converters after installation, a function test
starts for ‘non-switchable‘ ECGs. The process takes a
few seconds. During this process the status LED on the
converter flashes (see function description of the respective converter). As these devices cannot switch the connected lamp themselves, the normal identification process through switch on/ switch off is not possible. The
identification therefore needs to occur via the LED.
12.2 Converter inhibit mode
12.1 Features
Principally a distinction is made between switchable and
non-switchable devices for self-contained battery lamps.
A switchable device can be directly connected to a lamp
just like a ‘normal’ ECG. In normal mode the light (usually
an LED) can be switched and dimmed via DALI. Emergency lights with switchable ECGs therefore require only
1 DALI device. The standard switch parameters and objects are available for these devices.
In contrast to the ’switchable‘ device, a ’non-switchable‘
device (converter) can only control the connected lamp in
an emergency. To use the same lamp in normal mode
(switching, dimming), a second, ‘normal‘ ECG is required.
These lights are therefore called emergency lights with 2
DALI devices. The two ECGs make a device pair. ‘Nonswitchable‘ devices use the DALI communication to
query the device status and to initiate mandatory test
phases. As these devices cannot switch or dim themselves, there are no parameters or objects for switch behaviour available for these devices.
During both new and post-installation the gateway recognises automatically, whether the connected device is a
‘switchable’ or ‘non-switchable’ ECG. However, because
of the DALI structure with its random assignment of short
addresses, the pairing of a ‘normal‘ device with a ’nonswitchable‘ device does not occur automatically. It has to
be performed manually on the parameter page in the
ETS.
The assignment is crucial for fault analysis purposes as
‘non-switchable‘ devices usually share the connected
lamp with a ‘normal’ device. Without the assignment, a
lamp failure may be double-counted. In addition, the
‘normal’ ECG in a pair is usually automatically disconnected from the power supply when the emergency light
is tested. This loss of function generates an ECG failure.
However, by making a pair, the gateway recognises
automatically, whether a real ECG failure has occurred or
whether the corresponding converter has simply been
tested. Only real ECG failures are taken into consideration for alarm and analysis purposes. Please remember
that both the pairing and the fact that the power of the
‘normal ECG’ is switched off by the emergency light ECG
in test mode mean that any burn-in mode of these ECGs
is interrupted.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Self-contained battery emergency lamps always change
into emergency mode if there is a power supply failure.
The lamp is now operated by the internal battery. However, it may become necessary at times to cut off the
power supply, for example during maintenance work or
the initialisation phase of a building. To prevent the lights
from switching into emergency mode, the converters can
be disabled via the push buttons and display on the device (see above). This converter inhibit mode is only
available for all connected devices at the same time. If
the power supply is turned off within 15 minutes after activating the mode, the connected lights do not change
into emergency mode and the lights remain switched off.
When the power resumes, the lights return to normal. If
the 15 minutes run out without a power loss, all converters are automatically re-set to normal mode.
12.3 Test mode
The gateway supports mandatory tests for self-contained
battery emergency lamps.
|
The legal regulations and norms vary in different
countries. Please make sure that you comply
with all country-specific requirements.
The gateway supports functional tests, long duration
tests and battery tests. Functional and long duration tests
can be started externally via KNX telegrams (1 Byte telegrams, see below) or via the device website. Alternatively
you may choose to set automatic test intervals. This
means tests are performed automatically via the connected converters. (Please check the converter description for the exact function.) Battery tests can be performed individually at any time. However, they are also
part of a functional or long duration test.
After a test has been completed, the test results are
available on the KNX bus via communication objects and
they may be recorded in the visualisation. The corresponding 3 Byte object is updated with the test result and
automatically sent after every new test. The object can
be queried at any time. The object provides the result of
the last test. In addition to the latest test result the object
also displays the current status (test pending, test running).
Seite 32 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
|
Please remember that the object is only up-dated
with the latest test result once the test has been
completed. If a test is started and the object is
queried before the test is complete (which can be
seen from the status flag “test pending” or “test
running) the test result shown is that of the previously completed test.
Alternatively, or in addition to reporting via communications objects to the bus, test results can be displayed on
the website if you select the respective converter.
The website displays the most recently executed test with
results and date/time of the test.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 33 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
13. ETS communication objects overview
Obj
Object name
Function
2
Broadcast, Set Value
Value
Type
Flags
1 Byte
CW
13.1 General communication objects
This object is used to set all connected lights to a certain
value. However, any connected ECGs that are in special
mode (Burn-In, Emergency Test, Panic Mode) are excluded
and the DALI bus is addressed sequentially. A delay between the value setting of the first and last light may hence
be visible. If none of the ECGs is in special mode, the value
setting is performed simultaneously via DALI Broadcast
telegrams.
The general communication objects 1 to 22 only exist
once and apply to the gateway as a whole.
3
The gateway communicates via the KNX bus based on
powerful communication stacks. Altogether 871 communication objects are available for the communication.
Activate
Emergency
Mode
Activate /
Stop
1 Bit
CW
This object is used to activate or stop the emergency mode
via the bus.
4
Activate Test
Mode
Activate /
Stop
1 Bit
CW
This object is used to activate or stop the test mode for
emergency lights with central battery via the bus. Selfcontained battery lamps are controlled individually.
5
Activate Night
Mode
Activate /
Stop
1 Bit
CW
This object is used to activate or stop the night-time mode
via the bus.
6
Obj
Object name
Function
Type
Flags
1
Broadcast,
On/Off
1 Bit
CW
Switching
DPT:
This object is used to switch all connected lights on or off.
However, any connected ECGs that are in special mode
(Burn-In, Emergency Test, Panic Mode) are not switched
and the DALI bus is addressed sequentially. A delay between the switching off the first and last light may hence be
visible. If none of the ECGs is in special mode, the switching
is performed simultaneously via DALI Broadcast telegrams.
The Broadcast function always switches to 0 or 100%. The
‘switch-off value’ and ‘switch-on value’ parameters are not
considered.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Scene invoke /
program
Scene No.
8 Bit
CW
This object is used to invoke or program scenes. Up to 16
scenes are available on the DALI gateway. To program a
scene, you must set the top bit:
Start
Program
Scene 1
0
128
Scene 2
1
129
………….
Scene 15
14
142
Scene 16
15
143
7
Effects start / stop Effect No.
8 Bit
CW
This object is used to start or stop effects. Up to 16 effects
are available on the DALI gateway. To start an effect, set
the top Bit. The effect stops when Bit 7 is deleted. This
means:
Effect Off
Effect On
Effect 1
0
128
Effect 2
1
129
………….
Effect 15
14
142
Effect 16
15
143
Seite 34 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
Obj
Object name
8
General Failure
Function
Yes/No
Type
Flags
Obj
Object name
1 Bit
CRT
14
ECG Failure
Exceeds
Theshold
This object is used to report the presence of a general failure in the connected DALI line independent of its type.
9
DALI Failure
Yes/No
1 Bit
Yes/No
1 Bit
Flags
1 Bit
CRT
This object is used to report that the total of all ECG failures
recognised by the gateway exceeds the set threshold.
15a
General Failure
Exceeds Theshold
Ja / Nein
Type
CRT
This object is used to report the presence of a DALI shortcircuit in the connected DALI line.
10
Function
ECG Failure in
Total
Value
1 Byte
CRT
This object is used to report the total amount of ECG failures recognised by the gateway.
CRT
15b
ECG Failure in
%
Value
1 Byte
CRT
This object is used to report that the total of all lamp, ECG
and converter failures exceeds the set threshold.
Alternatively, this object is used to report the failure rate as
a percentage of the total number of ECGs in the DALI line.
11a
16
General Failure in Value
Total
1 Byte
CRT
This object is used to report the total number of all lamp,
ECG and converter failures recognised by the gateway.
Please remember that for each connected device a fault is
counted just once. A simultaneous lamp failure in case of
an ECG or converter failure cannot be recognised or
counted.
11b
General Failure
in %
Value
1 Byte
CRT
Alternatively, this object is used to report the failure rate as
a percentage of the total number of devices in the DALI line.
All lamp, ECG and converter failures are hereby taken into
consideration Please remember that for each connected
device a fault is counted just once. A simultaneous lamp
failure in case of an ECG or converter failure cannot be
recognised or counted.
Lamp Failure
Exceeds
Theshold
Ja / Nein
1 Bit
CRT
This object is used to report that the total of all lamp failures
recognised by the gateway exceeds the set threshold.
13a
Lamp Failure in
Total
Value
1 Byte
CRT
This object is used to report the total amount of lamp failures recognised by the gateway.
13b
Lamp Failure in
%
Value
1 Byte
CRT
This object is used to report the failure rate as a percentage
of the total number of lamps in the DALI line.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Yes/No
1 Bit
CRT
This object is used to report that the sum of converter failures recognised by the gateway exceeds the set threshold.
17a
Converter Failure in Total
Value
1 Byte
CRT
This object is used to report the total amount of all converter
failures recognised by the gateway.
17b
Converter Failure in %
Value
1 Byte
CRT
Alternatively, this object is used to report the failure rate as
a percentage of the total number of converters in the DALI
line.
18
12
Converter Failure Exceeds
Theshold
Status Switching Lamp
Status
8 Bit
CWT
This object is used to send the switch status of individual
lamps in the DALI line when the system is started or when a
change has taken place. Bit 0 - 5 refer to the number of the
ECG. Bit 6 shows the corresponding status on/off. For example:
Bit 7 6 5 4 3 2 1 0
ECG 5 / On
0 1 0 0 0 1 0 0
ECG 6 / Off
0 0 0 0 0 1 0 1
If a value is received where Bit 7 and Bit 6 are set, it is interpreted as a status query. For example:
ECG 5 / Query
Bit 7 6 5 4 3 2 1 0
1 1 0 0 0 1 0 0
The gateway responds with the current status of the queried
ECG.
Bit 7 6 5 4 3 2 1 0
ECG 5 / On
0 1 0 0 0 1 0 0
Seite 35 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
Obj
Object name
Function
Type
Flags
19
Status Value
Lamp
Status
16 Bit
CWT
Time and Date
Time stamps are used for the analysis of self-contained
emergency ballast faults. This requires the current date
and time which are made available via the Bus. Two objects are used for this purpose.
This object is used to send the value status of individual
lamps in the DALI line when the system is started or when a
change has taken place. Bit 8 to 13 refer to the number of
the ECG. Bit 14 shows the switch status. Bit 0 to 7 represent the corresponding status 0..100%. For example:
Obj
Object name
Function
Type
Flags
21
Time
Time
3 Byte
CWT
ECG 5 / On
Value 50%
This object is used to set the time. The time must be provided by a central timer and updated at least twice a day.
0 1 0 0 0 1 0 0
1 0 0 0 0 1 0 0
Bit 15..8
Bit 7..0
If a value is received where Bit 14 and Bit 15 are set, it is interpreted as a status query. For example:
ECG 5 / Query
1 1 0 0 0 1 0 0
0 0 0 0 0 0 0 0
Bit 15..8
Bit 7..0
The gateway responds with the current status of the queried
ECG.
ECG 5 / On
Value 50%
20
0 1 0 0 0 1 0 0
1 0 0 0 0 1 0 0
Failure Status Status
Bit 15..8
Bit 7..0
8 Bit
22
Date
Date
3 Byte
CWT
This object is used to set the date. The date must be provided by a central timer and updated at least twice a day.
Leap years and change-over to and from daylight saving
time are not taken into consideration during internal calculations of time and date. Therefore please pay attention that
the timer sends the correct date on these occasions.
CWT
Lamp/ECG
This object is used to send the failure status of lamp or
ECG failures in the DALI line when the system is started or
when a change has taken place. Bit 0 to 5 refer to the number of the ECG. Bit 7 represents an ECG failure, Bit 6 a
lamp failure. For example:
Bit
ECG 5 / ECG failure
ECG 6 / Lamp failure
7 6 5 4 3 2 1 0
1 0 0 0 0 1 0 0
0 1 0 0 0 1 0 1
If a value is received where Bit 6 and Bit 7 are set, it is interpreted as a status query. For example:
ECG 5 / Query
Bit 7 6 5 4 3 2 1 0
1 1 0 0 0 1 0 0
The gateway responds with the current failure status of the
queried ECG.
Bit 7 6 5 4 3 2 1 0
EVG 5 / ECG failure 1 0 0 0 0 1 0 0
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 36 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
13.2 ECG-related communication objects
A set of 11 communication objects is available for each
one of the up to 64 connected ECGs / converters and
corresponding lamps. The communication objects are
only shown for those ECGs / converters that were found
during system installation. The objects are also partly
hidden when ECGs have been assigned to a group.
|
Lamps can only be controlled individually if they
have not been assigned to a group.
The following objects are available (Example ECG 1):
Obj
Object name
170
ECG1,
Burn In
Function
Type
Flags
On/Off
1 Bit
CWT
This object is used to start or finish the automatic burn-in of
ECG1. During the burn-in process all other switch, dim or
value telegrams are ignored and the lamp runs at full light
level. The burn-in period normally finishes automatically after the configured burn-in time. If you switch the burn-in period off via this object, the timer stops and you need to restart the automatic burn-in.
171
ECG1, Status
On/Off
1 Bit
CRT
This object is used to send the ECG switch status. Any
value >0% is interpreted as ON.
172
ECG1, Status
Value
8 Bit
CRT
This object is used to send the ECG value status.
173
a
Obj
Object name
167
ECG1,
Switching
Function
Type
Flags
On/Off
1 Bit
CW
This object is used to switch an ECG on or off if it is not in
special mode (burn-In, test mode emergency lights, panic/
emergency mode).
168
ECG1,
Dimming
Brighter /
Darker
4 Bit
169
ECG 1,
Set Value
Value
1 Byte
CW
This object is used to set the value of ECG1 unless it is in
special mode (burn-in, test mode emergency lights, panic/
emergency mode).
On/Off
1 Bit
CRT
This object is used to send the failure status of lamp, ECG
and converter failures.
173
b
Failure Status,
ECG1
Status
1 Byte
CRT
Alternatively this object is used to send the failure status for
lamp, ECG and converter failures as a 1Byte object.
Bit 0  Lamp failure
Bit 1  ECG failure
Bit 2  Converter failure
CW
This object is used for the relative dimming of an ECG that
is not in special mode (burn-in, test mode emergency lights,
panic/ emergency mode). Bit 4 is set to dim up and deleted
to dim down. Bits 0..3 refer to the increment size. Bit 0..3
deleted is interpreted as a stop telegram.
ECG1,
Failure Status
174
ECG1, Operating Hours
Value
4 Byte
CRT
The operating hours of a lamp are sent via this object. The
internal counter can be set to 0 (Reset) or another value via
this object.
Please remember: The “Write“ flag is switched off in the
presetting.
175
ECG1, Life
Time Exceeded
Yes/No
1 Bit
CRT
This object is used to send a status message when the configured life time of a lamp is exceeded.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 37 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
DALI device as converter
If the connected DALI device is a converter for the control of self-contained battery emergency lights, two further
objects are shown:
Obj
Object name
176
Converter 1,
Test Start
Function
Start
Type
Flags
1 Byte
CW
This object is used to start a long duration test, functional
test and battery test of the converter. The individual Bits
have the following meaning:
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Start functional test
177
Converter 1,
Test Result
A set of 8 communication objects is available for each
one of the up to 16 possible groups. The communication
objects are only shown for those groups that are in use.
|
ECGs / that have been assigned to a group can
no longer be controlled individually.
The following objects are available (Example group 1):
Functional test pending
Start long duration test
Long duration test pending
Query battery status
Battery status query pending
Test
3 Byte
CRT
This object is used to analyse the results of functional tests,
long duration tests and battery tests. The individual Bits
have the following meaning:
Bit 23..16
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
13.3 Group-related communication objects
If test is function or batterie test: Battery status 0..100%
If test is duration test: Test time of duration test in steps of 2
minutes
Fault during long duration test
Fault during functional test
Maximum time for long duration test exceeded
Maximum time for functional test exceeded
Emergency light faulty
Battery faulty
Battery operating hours too short
Converter faulty
Long duration test pending
Function test pending
Duration test running
Function test running
Test error during the last test
Last test was battery query
Last test was duration query
Last test was function test
The objects described above for ECG 1 / converter 1 are
available in the same format for the ECGs / converters 2
to 64. The object number always increases by 11 objects.
For example, ECG 2: dimming  object 179, etc.
Obj
Object name
23
Group1,
Switching
Function
Type
Flags
On/Off
1 Bit
CW
This object is used to switch group 1 on or off.
24
Group1,
Dimming
Dimmen
4 Bit
CW
This object is used for the relative dimming of group 1. Bit 4
is set to dim up and deleted to dim down. Bits 0..3 refer to
the increment size. Bit 0..3 deleted is interpreted as a stop
telegram.
25
Group 1,
Set Value
Value
1 Byte
CW
This object is used to set the value of group 1.
26a
Group 1,
Enabled
Yes/No
1 Bit
CW
This object is used to enable the operation of group 1:
Object = 0  Disabled
Object = 1  Enabled
26b
Group 1,
Disabled
Yes/No
1 Bit
CW
This object is used to disable the operation of group 1:
Object = 0  Enabled
Object = 1  Disabled
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 38 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
Obj
Object name
Function
Type
Flags
Obj
Object name
26c
Group 1,
Disable Staircase Function
Yes/No
1 Bit
CW
31a
Group 1,
Failure Status
Function
Failure Status
Type
Flags
1 Bit
CRT
This object is used to send a message when the total of all
lamp, ECG and converter failures found within the group
exceeds the threshold set by parameters.
This object is used to disable the staircase mode:
Object = 0  Staircase mode enabled
Object = 1  Staircase mode disabled
31b
27
Group 1, Status On/Off
1 Bit
CRT
This object is used to send the switch status of the group.
Any value >0% is interpreted as ON.
Group 1, Status Value
8 Bit
CRT
This object is used to send the value status of the group.
29a
Group 1,
Failure Status
Yes/No
1 Bit
Value
1 Byte
CRT
This object is used to send the total of all lamp, ECG and
converter failures within the group.
31c
28
Group 1,
Failure
Group 1,
Failure Rate
Value
1 Byte
CRT
This object is used to report the failure rate as a percentage
of the total number of devices within the group.
CRT
This object is used to send the failure status of a lamp, ECG
or converter failure within the group.
29b
Group 1,
Failure Status
Status
1 Byte
CRT
This object is used to send the failure status for lamp, ECG
and converter failures within the group as a 1Byte object.
Bit 0  Lamp failure
Bit 1  ECG failure
Bit 2  Converter failure
30
Group 1,
Failure Status
Status
4 Byte
CRT
This object is used to report the total number of devices
within the group and the failure status according to type of
failure. The different Bits within the object have the following
meaning:
Bit 31
Norm. ECG
Bit 30
Emerg. ECG
Bit 29..24
Number of ECG + converter
failures
Bit 23
Norm. Lamp
Bit 22
Emerg. Lamp
Bit 21..16
Number of lamp failures
Bit 15
Def. Conv.
Bit 14
idle
Bit 13..8
Number of converters
Bit 7
idle
Bit 6
idle
Bit 5..0
Number of ECGs
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 39 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
14. ETS parameter settings
The ETS parameters of the device are distributed across
different parameter pages. To simplify the overview, only
the parameter pages of the device selected in the function tree are displayed.
14.1 Device: General Settings
Parameter
Settings
Password User Access
0
You can configure a password for the user area of the website. Passwords consist of numbers between 0 and 9999.
Password Admin Access
0
You can configure a password for the configuration area of
the website. Passwords consist of numbers between 0 and
9999.
14.1.2 Parameter page: IP Settings
The ”General Settings“ item has 5 parameter pages. The
parameters are described below:
Parameter
Settings
IP Address (byte 1)
0
IP Address (byte 2)
0
IP Address (byte 3)
0
IP Address (byte 4)
0
This sets the fixed IP address of the gateway if you do not
select the DHCP mode.
14.1.1 Parameter page: General
Parameter
Settings
Device Name
(max. 30 char.)
<Dali gateway IP>
Use this parameter to enter a user-friendly name for the
DALI gateway.
IP Adress Assignment
Manual Input
via DHCP
The gateway can either be assigned a fixed IP address or a
dynamic address assigned by a DHCP server. The parameters for the fixed IP address are only visible if you select
”Manual Input“.
Disable Button Operation
No
Yes
Use this parameter if you would like to disable the control
and configuration of the device via its display and push buttons. This option is to prevent manipulation of a running installation.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Subnet Mask (byte 1)
255
Subnet Mask (byte 2)
255
Subnet Mask (byte 3)
255
Subnet Mask (byte 4)
0
This sets the subnet mask of the gateway if you do not select the DHCP mode.
Gateway Address (byte 1)
255
Gateway Address (byte 2)
255
Gateway Address (byte 3)
255
Gateway Address (byte 4)
0
This sets the address of a standard gateway for direct access via the Internet. The setting is only possible if you do
not select the DHCP.
Seite 40 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
14.1.3 Parameter page: Behaviour
Parameter
Settings
Behaviour on KNX Failure
No Action
Switch to On-Value
Parameter
Settings
Use this parameter to set a delay for sending status objects
after KNX voltage recovery or a bus reset. In installations
with more than one gateway different settings for this parameter can prevent all devices from sending at the same
time.
Switch to Off-Value
Switch to Emergency Value
Use this parameter to set the behaviour of the connected
ECGs/lamps on KNX failure.
Behaviour on KNX Voltage
Recovery
Switch to Last Value
Switch to Off-Value
Use this parameter to set the behaviour of the connected
ECGs/lamps on KNX voltage recovery or bus reset.
Send on Request
If Change > 20%
inactive
Use this parameter to set whether and when you would like
a status value to be sent via a 4 bit dim telegram during
dimming (relative dimming). If you use the setting inactive
the value is only sent after the dimming process is complete.
Behaviour after Burn In
Switch to Off-Value
Switch to On-Value
Send on Change and after
Busreset
Switch to Last Value
No Delay
1 Second
Use this parameter to set the light value of ECGs / lamps
after their burn-in period. If you use ‘Switch to Last Value’
the value prior to the burn-in is saved and the lamp returns
to this value afterwards.
Behaviour after Emergency Switch to Off-Value
Test
Switch to On-Value
2 Seconds
3 Seconds
4 Seconds
5 Seconds
10 Seconds
Use this parameter to set a delay between individual status
telegrams. This can help to prevent a large bus load, for
example for broadcast switching.
Delay for Sending on KNX
Recovery
If Change > 5%
Send on Change
Use this parameter to determine the light status send conditions (switch status and value status) of the connected
ECGs and groups.
Delay between Status Objects
If Change > 2%
If Change > 10%
No Action
Switch to On-Value
Light Status Send Condition
Send Status Value During
Dimming
immediately
5 Seconds
10 Seconds
15 Seconds
Switch to Last Value
Use this parameter to set the light value of ECGs / lamps
after a central battery emergency luminaire test. If you use
‘Switch to Last Value’, the value prior to the test mode is
saved and the lamp returns to this value afterwards.
Behaviour after Panic /
Emergency Mode
Switch to Off-Value
Switch to On-Value
Switch to Last Value
Use this parameter to set the light value of ECGs / lamps
after the panic/emergency mode has finished. If you use
‘Switch to Last Value’, the value prior to the panic mode is
saved and the lamp returns to this value afterwards
20 Seconds
30 Seconds
40 Seconds
50 Seconds
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 41 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
14.1.4 Parameter page: Special Functions
Parameter
Parameter
Settings
Cycle Time for DALI Failure No Delay
request
0,5 Seconds
General Status Object (1
Byte) for Switching Status
No
1 Second
Yes
2 Seconds
3 Seconds
Use this parameter to select whether you would like to use
the general status object for switch status (object number
18).
General Status Object (2
Byte) for Value
No
Yes
Use this parameter to select whether you would like to use
the general status object for value status (object number
19).
Broadcast enabled
No
Yes
Use this parameter to select whether you would like to use
Broadcast functions.
14.1.5 Parameter page: Analysis and Service
4 Seconds
5 Seconds
6 Seconds
To analyse ECG and lamp failures, a periodic request has
to be sent to the ECGs via DALI telegrams. Use this parameter to set the time for these periodic requests.
|
If you set ‘No request‘ ECG and lamp failures can
no longer be recognised. You should therefore
use this setting only for service or in special
cases.
Central Failure Object 1
Byte existing
Settings
Failure Status Send Condition
Send on Request
Send on Change
Send on Change and after
Bus reset
Use this parameter to set the conditions under which you
want the failure status of the connected ECGs and groups
to be sent.
No
Yes
Use this parameter to select whether you want to use the
central failure object for ECG and lamp failures (object
number 20).
Function of Failure Objects
Parameter
Settings
Total Number of Failures
Failure Rate 0..100%
Use this parameter to select whether you want to use the
failure analysis objects (objects number 11, 13, 15 and 17)
to report the total amount of failures or the failure rate in %.
Threshold for Total Failures 1%
2%
3%
…..
Delay between Sending of
Failure Objects
No Delay
1 Second
2 Seconds
3 Seconds
4 Seconds
100%
Use this parameter to configure a threshold value for the
general failure alarm object (object 10). The threshold value
takes all failures (ECG, lamp and converter failure) into
consideration and relates them to the total number of connected ECGs and converters.
5 Seconds
10 Seconds
Use this parameter to set a delay between individual failure
objects. This can help to prevent a large bus load, for example when a DALI line loses power.
Threshold for Lamp Failures
1%
2%
3%
…..
100%
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 42 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
Parameter
Settings
Use this parameter to set a threshold value for the lamp
failure alarm object (object 12). The threshold value takes
all lamp failures into consideration and relates them to the
total number of connected lamps in the DALI line.
14.2 ECG No. xx
To set the ECG parameters, use the parameter pages
listed under the devices ECG 1 to ECG 64.
Threshold for ECG Failures 1%
2%
3%
…..
100%
Use this parameter to set a threshold value for the ECG
failure alarm object (object 14). The threshold value takes
all ECG failures into consideration and relates them to the
total number of connected ECGs in the DALI line.
Threshold for Converter
Failures
1%
2%
Please remember that after the synchronisation only
those ECGs are displayed that were recognised during
the installation. Accordingly there are fewer entries in the
function tree and fewer parameters and objects.
3%
…..
100%
Use this parameter to set a threshold value for the converter failure alarm object (object 16). The threshold value
takes all converter failures into consideration and relates
them to the total number of connected converters in the
DALI line.
There are 4 parameter pages for ECG settings. The parameters are described below.
14.2.1 Parameter page: ECG No. xx
Parameter
Settings
ECG Type
Fluorescent Lamp
Self Contained Battery Lamp
Discharge Lamp
Low Voltage Halogen Lamp
Incandescent Lamp
0..10V Converter
LED Module
Relais Module
Use this parameter to set the type of ECG used. Normally
the ECG type is recognised automatically during installation
and set accordingly in the synchronisation. Some ECG
manufacturers, however, do not support this function. In this
case, you can set the ECG type manually. During the synchronisation process, the ETS compares the found value to
the pre-set value. If the two do not match, an alarm message appears that has to be acknowledged.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 43 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
Parameter
Settings
Parameter
Settings
Emergency Luminaire with
Central Battery
No Emergency Luminaire
Converter controls
ECG 1
Use this parameter to set whether the ECG controls an
emergency luminaire with central battery. Devices registered as emergency luminaires are specifically marked during status reports. A special test mode for such devices can
also be activated via an object. This parameter is not visible
if you select the type “self-contained battery lamp”.
Value in Test Mode
1..100% [30]
Use this parameter to select the value of a lamp in ‘test
mode‘. A lamp in this mode cannot be switched or changed.
It remains at the set level.
This parameter is only visible if you select ‘Central Battery
Emergency Luminaire’.
Duration in Test Mode
ECG 2
Central Battery Emergency
Luminaire
5 Minutes
10 Minutes
…
ECG 64
not assigned
This parameter is only visible if you select a non-switchable
converter as type of emergency light. Non-switchable converters are normally used for an emergency lamp with two
DALI devices. Use the parameter to manually select the
“normal ECG“ that is assigned to the converter. The assignment means that error messages that were caused by
the converter test mode are suppressed and a lamp failure
is not counted twice.
Operating Mode
Normal Mode
Permanent Mode
Normal / Night Mode
Use this parameter to select the operating mode of the
ECG.
15 Minutes
….
Value in Permanent Mode
1..100% [50%]
4 Hours
Use this parameter to set the duration of the test mode. A
lamp in this mode cannot be switched or changed. It remains at the set level.
Use this parameter to select the value of a lamp in ‘permanent mode‘. A lamp in this mode cannot be switched or
changed. It remains at the set value.
This parameter is only visible if you select ‘Central Battery
Emergency Luminaire’.
This parameter is only visible if you select ‘permanent
mode’.
Type of Emergency Light
Behaviour in Night Mode
Switchable Converter (1 DALI
Device)
Non Switchable Converter (2
DALI Devices)
Use this parameter to select whether an emergency light is
used with a switchable or non-switchable converter. This
parameter is only visible if you select “self-contained battery
lamp” as ECG type.
Normally the ECG type is recognised automatically during
installation and set accordingly in the synchronisation.
Some ECG manufacturers, however, do not support this
function. In this case, you can set the ECG type manually.
During the synchronisation process, the ETS compares the
found value to the pre-set value. If the two do not match, an
alarm message appears that has to be acknowledged.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Delayed Switch-Off
Delayed Switch-Off in 2 Steps
Delayed Dimm-Off
Activate Permanent Mode and
ignore Telegrams
Use this parameter to set the behaviour of the ECG in nighttime mode. This parameter is only visible if you select ‘normal / night mode’.
Seite 44 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
Parameter
Settings
Automatic Switch-Off after
1 Minute
2 Minutes
3 Minutes
4 Minutes
5 Minutes
10 Minutes
15 Minutes
20 Minutes
Use this parameter to set the time after which an ECG in
night time mode automatically switches off. This parameter
is only visible if you select ‘normal / night mode’.
ECGs enabled for Panic
Mode
14.2.2 Parameter page: Emergency Settings
This page is only visible if you select ‘self-contained battery lamp’ as ECG type.
Parameter
Settings
Value in Emergency Mode
1..100% [50]
Use this parameter to select the light value of a self contained battery lamp in case of a mains supply failure or during a long duration test.
Delay on Mains Recovery
30 Seconds
No
1 Minute
Yes
2 Minutes
Use this parameter to enable an ECG for panic mode.
Value on DALI Power Fail
3 Minutes
4 Minutes
1..100% [100]
Use this parameter to set the value of a lamp after a loss of
DALI power. The value is saved on the ECG and the device
automatically changes to the value when a power loss occurs.
No Delay
5 Minutes
10 Minutes
Use this parameter to set the delay till a self contained battery lamp returns to normal mode following mains recovery.
Interval of Long Duration
Test
No automatic testing
1 Week
2 Weeks
….
52 Weeks
Use this parameter to set the intervals at which the converter is to perform automatic long duration tests.
Interval of Functional Test
No automatical Testing
1 day
2 days
….
28 days
Use this parameter to set the intervals at which the converter is to perform automatic functional tests.
Test Execution Timeout
(Days)
0..255 [10]
If a functional or long duration test cannot be started immediately (for example because the battery was not full), the
converter tries to execute the test later on. Use this parameter to set the length of time that the converter is to try to
execute the test and after which a test execution timeout error is reported. If you select 0, the timeout occurs after 15
minutes.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 45 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
14.2.3 Parameter page: Switching Behaviour
Parameter
Settings
Value-Set Behaviour
Set Value Immediately
Dim to Value in 10s
Parameter
Settings
Dim to Value in 20s
Switch-On Value
5%
Dim to Value in 30s
10%
Dim to Value in 1 Minute
…
Dim to Value in 2 Minutes
95%
Dim to Value in 5 Minutes
Dim to Value in 10 Minutes
100%
last Value
Use this parameter to set the switch-on value. If you select
‘last value‘, the value is set to the dim value prior to the
lamp being switched off.
Switch-On Behaviour
Use this parameter to value-set the behaviour on receipt of
a new dim value.
Time for Dimming
0 … 100 %
3 Seconds
4 Seconds
Set Value Immediately
5 Seconds
Dim to Value in 10s
6 Seconds
Dim to Value in 20s
10 Seconds
Dim to Value in 30s
20 Seconds
Dim to Value in 1 Minute
30 Seconds
Dim to Value in 2 Minutes
Dim to Value in 5 Minutes
60 Seconds
Use this parameter to set the dim time for relative dimming.
Dim to Value in 10 Minutes
Use this parameter to set the switch-on behaviour.
Max. Value for Dimming
50%
55%
Switch-Off Value
0%
….
5%
100%
10%
…
Use this parameter to configure the maximum dim value
that can be set through relative dimming.
45%
50%
Min. Value for Dimming
0%
5%
Use this parameter to set the switch-off value.
….
Switch-Off Behaviour
50%
Set Value Immediately
Dim to Value in 10s
Dim to Value in 20s
Dim to Value in 30s
Dim to Value in 1 Minute
Dim to Value in 2 Minutes
Dim to Value in 5 Minutes
Dim to Value in 10 Minutes
Use this parameter to configure the minimum dim value that
can be set through relative dimming.
Switch-On via Dimming
No
Yes
Use this parameter to select whether a switched off device
can be switched on when receiving a relative 4 Bit dim
command ‘dimming up‘.
Use this parameter to set the switch-off behaviour.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 46 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
14.2.4 Parameter page: Analysis and Service
Parameter
Einstellungen
Operating Hour Calculation
Yes
14.3 Group Nr. xx
To set the group parameters, use the parameter pages
listed under group1 to group 16.
No
Use this parameter if you would like to count the individual
operating hours of an ECG.
Operating Hour Limit
(hours)
10..120.000h [4000h]
Use this parameter to set the limit of a lamp’s operating
hours. An alarm is sent when the limit is reached.
Enable Burn In Feature
Yes
No
There are 3 parameter pages for group settings. The parameters are described below.
Use this parameter to enable the burn in feature.
Burn In Duration (hours)
1..100h [24h]
Use this parameter to set the duration of the burn-in phase.
During this phase the lamp cannot be switched off or
dimmed.
Type of Failure Object
14.3.1 Parameter page: Group number xx
Parameter
Settings
Operating Mode
Normal Mode
Permanent Mode
Normal / Night Mode
1 Bit
8 Bit
Use this parameter to select whether the failure object is to
be sent as a 1 Bit object without differentiation according to
type of failure or as an 8 Bit object with failure differentiation.
Staircase Mode
Use this parameter to set the operating mode of the group.
Value in Permanent Mode
0..100% [100]
Use this parameter to select the value of all lamps in a
group in ‘permanent mode‘. Lamps in this mode cannot be
switched or changed. They remain at the set value.
Behaviour in Night Mode
Delayed Switch-Off
Delayed Switch-Off in 2 Steps
Delayed Dim-Off
Activate Permanent Mode and
ignore telegrams
Use this parameter to set the behaviour of the group in
night-time mode. This parameter is only visible if you select
‘normal / night mode’.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 47 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
Parameter
Settings
Automatic Switch-Off after
1 Minute
14.3.2 Parameter page: Switch behaviour
2 Minutes
Parameter
Settings
3 Minutes
Switch-On Value
1%
4 Minutes
10%
5 Minutes
…
10 Minutes
95%
15 Minutes
100%
20 Minutes
last Value
Use this parameter to set the time after which a group in
night time mode automatically switches off. This parameter
is only visible if you select ‘normal / night mode’.
Use this parameter to set the switch-on value. If you select
‘last value‘, the value is set to the dim value prior to the
lamps being switched off.
Function of Additional Object
Switch-On Behaviour
No Object
Set Value Immediately
Disable Object
Dim to Value in 10s
Release Object
Dim to Value in 20s
Disable Staircase Function
Object
Dim to Value in 30s
Dim to Value in 1 Minute
Use this parameter to set the function of an additional object.
Dim to Value in 2 Minutes
Dim to Value in 5 Minutes
Enabled for Emergency /
Panic Mode
Dim to Value in 10 Minutes
No
Yes
Use this parameter to enable a group for panic/emergency
mode.
Use this parameter to set the switch-on behaviour.
Switch-Off Value
0%
5%
10%
…
45%
50%
Use this parameter to set the switch-off value.
Switch-Off Behaviour
Set Value Immediately
Dim to Value in 10s
Dim to Value in 20s
Dim to Value in 30s
Dim to Value in 1 Minute
Dim to Value in 2 Minutes
Dim to Value in 5 Minutes
Dim to Value in 10 Minutes
Use this parameter to set the switch-off behavior.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 48 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
Parameter
Settings
Value-Set Behaviour
Set Value Immediately
14.3.3 Parameter page: Analysis and Service
Dim to Value in 10s
Dim to Value in 20s
Parameter
Settings
Dim to Value in 30s
Type of Failure Status Object
1 Bit
Dim to Value in 1 Minute
Dim to Value in 2 Minutes
Dim to Value in 5 Minutes
Dim to Value in 10 Minutes
Use this parameter to value-set the behaviour on receipt of
a new dim value.
Time for Dimming
3 Seconds
4 Seconds
5 Seconds
6 Seconds
10 Seconds
20 Seconds
30 Seconds
60 Seconds
Use this parameter to set the dim time for relative dimming.
Max. Value for Dimming
50%
55%
….
100%
Use this parameter to configure the maximum dim value
that can be set through relative dimming.
Min. Value for Dimming
8 Bit
Use this parameter to select whether you want the failure
status object of the group to be sent as a 1 Bit object without type of failure information or as an 8 Bit object with failure differentiation.
Additional Failure Object
for
Failure Number / Rate
Failure Threshold Exceeded
Use this parameter to select whether you would like to use
the additional failure object as a 1 Byte object for failure
number /rate or as a 1 Bit object for when the failure
threshold is exceeded.
Failure Threshold for Failure Alarm Output
1%...100% [1%]
Use this parameter to enter the threshold value in %. The
alarm object is sent when the value is exceeded. This parameter is only visible if you select “Failure Threshold Exceeded“ as additional failure object.
Function of Additional Failure Object
Total Number of Failures
Failure Rate 0..100%
Use this parameter to select whether you want the additional failure object to send the total amount of failures
within the group or the failure rate in %. This parameter is
only visible if you select “Failure Number / Rate“ as additional failure object.
0%
5%
….
50%
Use this parameter to configure the minimum dim value that
can be set through relative dimming.
Switch-On via Dimming
No
Yes
Use this parameter to select whether a switched off group
can be switched on when receiving a relative 4 Bit dim
command ‘dimming up‘.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 49 von 50
KNX DALI gateway REG-K/1/16(64)/64/IP1
Art. no. MTN6725-0001
Application DALI Control IP1 7307/1.0a
15. Firmware update
16. Reset to conditions at delivery
The firmware version of the DALI gateway is divided into
main number, sub-number and revision number (e.g.
1.0_10). The display on the device front only shows the
main and sub-number (Vers. 1.0). For full details regarding the current firmware (version and revision) please refer to the device website where the current version is visible in the bottom right-hand corner of the information
window. (1.0_10).
To reset the device to its original settings, press all three
buttons on the front of the device and the programming
button simultaneously whilst the power supply is connected.
This leads to a factory reset. All device settings return to
their status at delivery and the device has the physical
address 15.15.255.
Schneider Electric Industries SAS
If you have technical questions, please contact the Customer Care Center in your country.
www.schneider-electric.com
The gateway offers you the possibility of an easy firmware upgrade without having to demount the device.
Future developments or any adjustments that may be required can be easily imported via the IP connection.
If there is an update, an update file will be made available to you within an update tool. The update file can be
directly downloaded onto the device via the tool. For
more details regarding this process, please see the application note (pdf format) included with the update.
Application DALI Control IP1 7307/1.0a
©
2013 Schneider Electric
Seite 50 von 50
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement