Tactical technologies TPS24-6AC Installation manual

Add to My manuals
4 Pages

advertisement

Tactical technologies TPS24-6AC Installation manual | Manualzz

24Vac 6A Series

MODELS :

TPS24-6AC

TPS24-6AC-BD2

TPS24-6AC-BD4

TPS24-6AC-BD10

©

2012 The contents of this manual are copyright and may not be reproduced without the written permission of

Tactical Technologies Pty Ltd.

N645

Installation Manual

DESIGNED & MANUFACTURED

®

C

AUTION

Equipment must be installed & serviced by suitably qualified service personnel in a restricted access area.

DANGER

HIGH VOLTAGE

General

These power supplies are designed for indoor use only.

Dangerous Voltages Inside !

Do not remove covers

No user serviceable parts inside

N645

TPS24-6AC models are available with 1, 2, 4 or 10 individually fused outputs - each provided with a LED indicator to display circuit status, a handy feature for quick troubleshooting of cabling or camera faults. The TPS24-6AC Series is particularly handy for installations requiring relatively high current output for a small number of cameras eg Pan

Tilt Zoom or IR Illuminators.

The Tactical 24AC Series includes models ranging from 2A to 20A output, with 1, 2, 4, 10 or 20 individual fused outputs (model dependant). Check www.tac-tec.com.au or your Tactical Distributor.

TPS24-6AC Model Variants:

TPS24-6AC

TPS24-6AC-BD2

TPS24-6AC-BD4

TPS24-6AC-BD10

24Vac 6A CCTV Power Supply in small enclosure ( 202L x 136W x 82H mm )

24Vac 6A CCTV Power Supply with 2 x 2A Fused Outputs ( 310W x 240H x 60D mm )

24Vac 6A CCTV Power Supply with 4 x 1A Fused Outputs ( 310W x 240H x 60D mm )

24Vac 6A CCTV Power Supply with 10 x 400mA Fused Outputs ( 310W x 240H x 60D mm )

Connection

TPS24-6AC has a single fused output with a single set of screw terminals.

TPS24-6AC-BDXX models are fitted with a Tactical Technologies PDM (2, 4 or10 way) Power Distribution Module.

In order to provide maximum short circuit protection, it is recommended that the installer assess the current draw of each device connected to the PDM and fit a fuse of appropriate value to suit.

Ensure that total device current draw does not exceed the rated output of the power supply, remembering to allow an adequate power margin for equipment cold start.

For your convenience, an LED is fitted adjacent to each fuse. The LED is lit when the fuse is intact and extinguished when the fuse has failed.

Note that TPS24-6AC-BDXX models have a 240V primary side fuse fitted in an integrated fuse holder within the IEC type Power Socket Connector fitted on the lower edge of the cabinet - TPS24-6AC has an inbuilt (non-serviceable) fuse inbuilt into the transformer.

www.tac-tech.com.au

TPS24-6AC Series_Rev C.pdf

E

F

G

A

B

C

D

Multi-Output Models

( e.g. TPS24-6AC-BD10 )

L

AYOUT

Single Output Model

( TPS24-6AC )

I

H

DESIGNED & MANUFACTURED

A Output Terminals ( Multi Output models only )

C Individual Circuit Status LEDs ( Multi Output Models )

E Anti-Surge MOV Network

G Output 24Vac 6A ( single output model )

I Compliance / Date of Manufacture Label

B PDM Input ( Multi Output models only ) - ‘G’ below

D Individual Circuit Fuses ( Multi Output models only )

F 6A Output fuse - (single output model only)

H Input Mains Fuse ( Integrated into IEC Mains Socket)

TPS24-6AC_Series_Rev C.pdf

www.tac-tech.com.au

Output Voltage

Output Current

Output Channels

Output per Channel

Input Voltage

Input Current

Input Fuse Rating

Weight

Dimensions

DOFT Approval No:

Safety Standards

EMC Standards

24Vac

6A Series

Specifications :

( In the interests of product improvement, Tactical reserves the right to change specifications without notice)

®

TPS24-6AC

1

6A not replaceable

< 2.5Kg

202L x 136W x 82H mm

TPS24-6AC-BD2

2

3A

TPS24-6AC-BD4

24 Vac

6A

4

1.5A

240 Vac / 50Hz

800mA RMS @ 240Vac

(T)1A / 250V

< 5Kg

310W x 240H x 60D mm

NSW 24012

AS/NZS 61558.1 including AS/NZS 61558.2.6

C-Tick

TPS24-6AC-BD10

10

600mA

®

www.tac-tech.com.au

Securing Your Power Needs

®

Now and into the Future . . .

Designed & Manufactured

Tel: +61 2 8822-1888 5 Butterfield St, Blacktown NSW 2148 Fax: +61 2 8822-1899

advertisement

Related manuals

Download PDF

advertisement