null  null
Upgradation of ITIs into Centres of ExcellenceBroad guidelines for implementation of Advanced Module of Sector
“Electronics ”.
These Centres will be providing multiskill training to meet the skill requirement of particular sector of industry with their active involvement in
all aspects of training. The training will be provided in three parts as given below:
♦ Training in Basic skill areas for a period of one year.
♦ Training in Advanced modules of six months duration after Broad based basic Training(BBBT)
♦ Testing & Certification both for the Broad Based Basic Training & Advanced Module Training during subsequent six months will be
conducted under the aegis of NCVT .
♦ Training in specialized modules mainly by the industry (The course curricula, duration etc will be designed in consultations with the
IMC/local industry). The trade testing & certification for specialized module will be done jointly by the State Government & Industry.
Said certificate will have recognization from NCVT
♦ As per the recommendations of the EFC, Training in the shop floor should constitute alteast 25-40% of the curriculum.
The training programme will have multi-entry and multi-exit provisions as given below:
•
•
trainee can opt to go to the labour market after completing broad based basic training of one year duration or after completing
advanced module/s.
multi-entry and multi-exit provisions would enable a trainee to take admission for advanced/ additional advanced /specialized module
as per his/her need .
Guidelines for Training in Advanced modules
A minimum of three modules would be essentially needed , so as to ensure that all the 96 trainees are accommodated in the
three modules may be selected in consultation with IMC for which in two shifts .
If it is felt that available modules for which the course curricula has been developed at National Level are not sufficient to cater
to the needs of local industry in a particular state, States are free to select module as per need in consultation with industry .
They may develop suitable module(s) accordingly in consultations with the industry clearly indicating tool & equipment list ,
instructor qualifications , space norms etc. & forward the same to DGE&T for seeking approval of NCVT.
A trainee at a time can opt only for one Advanced Module .
Admission Criteria, Space requirement, Qualification of instructor of the various modules of “Electronics
attached herewith.
” sector are
1
Admission to Advanced Module for the graduates of ITI in related trades:
There is a provision for lateral entry for graduates of ITIs (NTC /NAC passed outs from conventional system ) of the related trades subject to
availability of seats in Advanced Module. Trades of conventional system mentioned against each advanced module in the enclosed statement,
could be offered admission in Advanced Module .
MODULE
Qualification/
Admission criteria
Space
Dura
NAME OF THE
NO.
Status Of
requirement tion
MODULE
Instructor
In
Wee
ks
70
sq
m
24
Degree in
EAT-01
Completed
BBBT
in
Sector
Electronics
OR
Radio , Audio ,
weeks Electronics with
NTC/NAC in Electronics Mechanic, Radio & TV, Consumer
Video System and
minimum two
Electronics
or
any
other
related
trade
Appliances
years
OR Diploma in Electronics
teaching/industria
Completed BBBT in Sector Electronics OR
EAT-02
Inverters, UPS
l experience in
NTC/NAC
in
Electronics
Mechanic,
Radio
&
TV
or
any
other
,Voltage stabilizers
the relevant field
related
trade
and Industrial
OR Diploma in Electronics
Drives
OR
Completed BBBT in Sector Electronics OR
EAT-03
Repair &
NTC/NAC in Electronics Mechanic, Instrumentation or any other
Maintenance of
Diploma in
related trade
Electronic Test
Electronics with
OR Diploma in Electronics
Equipment
min four years
Completed BBBT in Sector Electronics OR
EAT-04
Automobile
teaching/industria
NTC/NAC
in
Electronics
Mechanic,
Auto
Electronic
or
any
other
l experience in
Electronics
related trade
the relevant field
OR Diploma in Electronics
Completed BBBT in Sector Electronics OR
EAT-05
Communication
OR
NTC/NAC in Electronics Mechanic, Radio & TV or any other
System
related trade
HNTC in
OR Diploma in Electronics
Related area
Completed BBBT in Sector Electronics OR
EAT-06
Embeded System
with min five
NTC/NAC in Electronics Mechanic, or any other related trade
years
and PLC
OR Diploma in Electronics
teaching/industria
l experience in
the relevant field
.
2
Advanced Module of Electronic Sector:
MODULE-1
Radio , Audio , Video system and Appliances
Theory
Practical
RADIO BASICS
AUDIO FUNDAMENTALS: Sound wave characteristics, Room,
Acoustics, Decibel, B.H. Curve, A.C./D.C. Bias, P.A. System ,
Amplifiers , Various microphones, speakers and their selection
RADIO FUNDAMENTALS: Modulation , Demodulation techniques,
Introduction to AM, FM & PM SSBSC & DSBSC
FM Generation & Detection : different method FM
Plot the Frequency Vs Output characteristics of various types of
Microphones and Speakers, Woofer/Tweeter, Baffles, Audio
Recording,
Find the modulation, Modulation Increase in various Modulation
techniques.
Radio Receivers: Types, Super heterodyne receiver Blocks, Principle,
characteristics, advantages and disadvantages, FM Receives, Preemphasis and De-emphasis, AFC in FM Receivers
RF, IF &AF Amplifier Sections: Gain, Frequency, Voltage , Power,
AGC, AVC Circuits squelch circuit in receives,
AM/FM RX Alignment, Radio Wave Propagation – Principle, Fading,
Antenna and Testing,
Audio Cassette recorder: Audio recording & playback principle ,
Audio Deck mechanism-layout & identification , Electronic circuitsblock diagram & description of each block, Dolby sound, Surround
sound system, Home theatre ,Impedance matching , speakers, graphic
equalizer, microphones.
ACD / VCD PLAYER
Working principle of ACD/VCD/DVD players, CD mechanism &
power supply , types of CD’s and writing procedure on CDs , five in
one system, MP3 formats / flash memory recording
Identify and test the various parts & control of Superhetrodyne
receiver
Fault findings of RF, IF and AF Amplifier Sections, AGC, AVC
Circuits squelch circuit
AM/FM RX Alignment
Identify the functions of different parts of different deck mechanism
Testing & fault finding in audio cassette recorder
Identify and study the various parts and control of ACD/VCD
players
3
Functional detail of circuits – Audio, RF, Encoder etc. , Digital
recording techniques , Digital audio receivers
Circuit , functional details and fault finding procedure of all
circuits
Laser fundamentals, optical pickup units, laser beam , CD recording
standards
Difference between ACD and VCD players, & DVD , ,MP easy card,
Single CD and 3 CD changer.
Fault finding procedure in different stages including CD drive
mechanism.
TELEVISION
Working principle, Basic Blocks – BW TV & CTV, Difference
between Black and White TV & Color TV Receivers, TV Systems and
Standards, Color TV Transmitter, Color fundamentals, Television
Transmission, VSB , Low Power Transmitters and High Power
Transmitters functions,
Camera Tubes: Light characteristics
Types of Tubes: Vidicon, Plumbicon , CCD and their working,
Camera circuit functioning, Electronic TV Tuner – Types & Features,
TV Antenna, TV Power Supply, Regulated Power Supplies, PS
Circuits using Integrated circuits, Switched mode power supply, CTV
Blocks,
Video camera:Specifications and working
Colour signal: Generation and Encoding Development of Sub-carrier,
modulation of Sub-carrier, Composite Video Signal, UV Signals
separation, UV Signals demodulation, Chroma Section and Delay line,
PAL-D colour receiver, colour signal decoding and matrixing, Video
IF and detector section. AGC and Sync Separator: AGC types, AGC
circuits and their adjustments, Horizontal oscillator, Horizontal and
vertical synchronization.
Sync Separator: Principle and circuits, Effect of noise in
synchronization, IC based circuits, faults in AGC and Sync Separator
stages.Horizontal and Vertical Sections: HOT Section, Switching
transistor functions, inputs in HOT, Outputs from EHT, Signal Flow
through different stages in the block. Vertical Sweep section, Vertical
section – blocks scanning, functions of related ICs, Input signals to
Circuit study of Audio, RF, Encoder etc.
Rectify the fault in the given circuit
Fault findings of given VCD player
Fault finding on given ACD / VCD drive mechanism
Study and fault findings of
optical pickup units, and drive mechanism ,to wire up ACD to VCD
conversion card
Identify, operate and adjust front panel controls of CTV Dismantle
TV and Identify the internal sections/ICs and Test points.
Review on power supplies.
TV Power supplies, SMPS, Testing and repairing, Familiarize with
various SMPS circuits.
Identify and test the Chroma section – Measure the voltage and
observe the wave form on chroma input and output sections. Fault
finding in chroma section, AGC sync and horizontal sections.
Identify and test the Horizontal , vertical sections
Trace the Sync separator, AFC and Horizontal oscillator circuits /
ICs and locate test points for measurement of voltages/wave forms
Trace and rectify the faults in a Horz. And Vert. Driver and out put
section
4
this stage, outputs from this stage,processing of Video signal –
Functions of related IC Video Amplifier ICs – Configuration and
functions.
Colour Picture tube – Parts and functions,Construction, function of
degaussing coil, functions of pure and convergent magnets, difference
between monochrome and colour picture tubes. TV Remote Control –
Types, parts and functions,IR Code transmitter and IR Code
Receiver,Working principle, operation of remote control. Different
adjustments,general faults in Remote Control.
LCD & Plazma TV,Digital & Projection TV
Domestic Appliances :
Microwave oven: Different types of oven,study the various functions
of Oven, Microwave generation system-circuit , description &
working ,study ,working of Power supply,various precautions to be
observed, Different aspects of servicing of Microwave Oven.
Washing M/c: different types of machines,Block diagram & basic
working principle of manual, semi automatic and fully automatic
machines,study the working of motors, different types of timers,
power supply circuits, Different aspects of servicing of Washing M/C
Vacuume cleaner-Block diagram,working principle, study of different
features of the machine,study & working of motor used , Electronic
circuit, power supply, Different aspects of servicing of Vacuume
cleaner.
Mixer/Grinder: Block diagram,working principle , study of different
features of machine , Study & working of motor used ,different
aspects of servicing of Vacuume cleaner.
Fax M/C: Block diagram, working principle, study of different
features of the machine, Various precautions to be observed, Different
aspects of servicing.
Computer Monitors :Block diagram ,working and study of their
different circuits,Different aspects of servicing of Monitors.
Photocopier & Photocopier cum Duplicator M/C:
Block diagram and working principle of Photo copier, study of front
panel and its features, mechanical system and electronic circuits of
photocopier and duplicatotrs, servicing aspects of m/c
Scanners: Block diagram, working principle, study of different
Trace and rectify the faults of a various remote controls
Identify the various controls and sections of Plasma , projection
TV,Digital TV
Dismantle and identification of various parts, wiring, tracing of
various controls, fault finding in Microwave oven.
Dismantle and identification of various parts, wiring, tracing of
various controls,Electronic circuits, fault finding in various types of
washing M/C.
Dismantle and identification of various parts, wiring, tracing of
various controls, Electronic circuits, fault finding in various types
of Vacuume cleaners.
Dismantle and identification of various parts, wiring, tracing of
various controls,Electronic circuits, fault finding in various types of
Mixers/grinders.
Identification of different blocks on assembled PCB, tracing of
different Monitor circuits.
Dismantle and identification of various parts, wiring, tracing of
various controls , Electronic circuits,mechanical system and its
assembly,fault finding in various types of machines.
Dismantle and identification of various parts,wiring , tracing of
various controls,Electronic circuits, fault finding in various types
5
features , servicing aspects of various types of scanners
Printers:DMP,Deskjet and Laser jet - Block diagram,working ,
different features ,mechanical and electronic system,power supply,
Different aspects of servicing
printers.
Dismantle and identification of various parts, various features,
Electronic circuits, loading of software,fault finding in various
types scanners.
6
Equipment List : Radio , Audio , Video system and Appliances
SL No
1
2
3
4
5
6
7
8
9
10
11
12
13
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
Description of Items
Trainee Tool Kit
Trimming kit
AM/FM Radio Receivers
MW/SW/FM Radio Receiver Trainer
Oscilloscope dual trace storage
AM/FM Signal Generator
Digital Multimeters
AF Power Meter
RF Power Meter
Temperature Controlled Soldering Station
Frequency Counters
DC Power Supply 0-30V, 1A
Washing Machine
Microwave Oven
Mixer / Grinder
Fax Machine
Colour T.V.
VCD Players
DVD Players
Computers
Scanners
Printers
Photo Copier
Qty
16
4
4
4
4
2
4
2
2
6
2
4
7
Space Norm
16 Mtrs
Advanced Module of Electronic Sector –
MODULE -2
8 Mtrs.
Inverters, UPS ,Voltage stabilizers and Industrial drives :
Theory
Review on Wires and Cables, their types, Voltage and current rating,
selection of cables for various applications , passive componentsResistor, Capacitors & Inductors,
Review of Electrical circuits,Faraday’s law of electromagnetic nduction,
Lenz’s law, Fleming’s right hand & left hand rule,Various controlling and
protective devices - Switches, main switches, Fuse, MCB, ELCB, relays
and S S Relays etc,
Electrical wiring for Single phase and Three phase systems, Earthing and
earth resistance measurement, calculation of load ,power and power factor
Review on Batteries – various types, their selection, grouping of cells and
batteries, charging of batteries,Various Battery charging circuits used in
Inverters and UPS , Maintenance of Batteries
Transformers – their types, core materials, ferrite core transformers,
Magnetic Hysterisis , various losses of transformers, Efficiency of
Transformers,3 phase transformers, Star / Delta connections, OC & SC
test of Transformers,Factors affecting the functions of transformers,
Selection of Tx for Inverter,UPS,Automatic & servo Voltage stabilizers
Diode, Power diodes –capacitance of diode, low frequency and high
frequency applications, Rectifiers, 3 phase rectifiers, Switching
action,period and power rating of transistors, low frequency and high
frequency transistors, Heat sinks – their types, ratings and their cooling
systems, Review of Power supply,filter circuits, ripple factor, High
current rectifier circuits, precaution and handling of rectifier circuits,
Power MOSFET, IGBT - their types, characteristics, switching speed,
power ratings and protection.
SCR–SCR as rectifier,Power ratings of SCR,Half and full wave ckts of
SCR,3 phase rectifiers,SCR Protection circuits,Power control using SCR
Practicals
Familiarise with various types of wires and cables
Exercises on High Wattage resistors, Capacitors , various types of
Inductors.
Identify the terminals and rating of various types of switches and
protective devices.
Understand the wiring circuits and protective devices used in
domestic and industrial wiring . Earth resistance measurement.
Familiarize with various types of batteries, grouping of batteries,
connectors used with batteries.
Assemble and test the various battery charging circuit
Identify and test the types of transformers. OC and SC test of
Transformers. Method to find the winding sequence of the
transformer.
Testing of Power Diodes and Power transistors.
Familiarise with various packages of diodes and Transistors.
Identification and selection of Heat sinks for various applications.
Assemble and test the high current rectifier circuits, measure
various parameters, find out the simulated fault and rectify
Testing methods used for MOSFET, IGBT. Familiarise with
various packs of MOSFET and IGBT, wire up a circuit and test
MOSFET/IWE working as switch.
Construct, half and full converters using SCR, measure various
8
parameters, construct a half converter circuit used s battery charger.
Assemble ,test the oscillators & wave shaping .Assemble and test
various oscillator circuits used in inverters.
Construct a PWM circuit using MOSGFET for DC power control
and measure various parameters.
Construct the electronic control circuit used in servo controlled
Manual & automatic and servo voltage stabilizers-concept and block
diagram, o/p voltage adjustment, voltage cutoff systems, study of different stabilizers using temp. ICs, TRIAC, adjust the circuit for low and
high voltage, over current cut-off.
types of relays used in stabilizers, study of electronic circuit commonly
used, buck and boost concept
Construct and test Inverters of various power ratings Installation of
Inverter – their principle & operation, power rating, change over period.
inverters,Test the various protection circuits used in Inverters,fault
Installation of Inverters, Protection circuits used in inverters– battery
finding in inverters.
level, over load, over charging etc.Various faults and its rectification
Three phase inverter circuits – principle and working.
Testing and Installation of Three phase Inverters
Microcontroller PLC 8051:Architecture,programming,instruction set
Execution of program instruction using Controller kit
Concept of UPS, OFF LINE and ONLINE . Difference between Inverters Assemble and test low power Off-line UPS circuits. Selection of
UPS
and UPS. Low power Off line UPS circuits. Selection of UPS –
calculation of load power,Line interactive UPS
ON- Line UPS, their circuit description and working- controlling circuits, Familiarise with the various types of ON-LINE UPS and their
Micro controller circuits, power circuits, charging circuits, alarm circuits, circuits. Fault finding in UPS.
Indicator circuits
Three phase UPS Circuits,Installation of single phase and 3 phase UPS.
3 phase UPS Circuits, Installation of single phase &3 phase UPS.
Understand all the information on a Motor template
DC Motors– types, working ,torque speed characteristics,staring of DC
Connect and run the DC Shunt motors, Speed control of DC shunt
Motors & change the DOR, 3 point and 4 point Starters,speed control of
motor.
DC motor, Field flux control & armature current control. Brushless DC
Motors.
Connect and run the 3 phase induction motor, Familiarise with the
Fundamentals of 3 phase & single phase Induction motors, synchronous
DOL, Star/delta and Transformer type starter
speed, slip, rotor frequency , torque – speed characteristics, Starters used
for Induction motors, speed control of Induction motors
DC drives-their principle and working, open loop speed control system
Construct and control PWM circuit for the speed control of DC
motors
Closed loop speed control system,speed sensing devices& circuits,Hall
Study & observe the O/P of various speed sensing Circuits
sensor,Opto couplers,Magnetic sensors,tacho generators,Back emf system
Closed loop control of DC shunt motor using various methods,rotating
Study constructional details & test the closed loop control DC
M/C load characteristics,Introduction to harmonics,
drive, identify and rectify them simulated parts in DC motor.
Closed loop speed control method for 3 phase induction motor, VF
Study the load characteristics of 3 phase induction motor.
Oscillators and wave shaping circuits: classification , Different 50 Hz
oscillator circuits, oscillator circuits used in Inverters, Sinewave
generation using PWm techniques.
9
method, rectifiers and filters used in VFD, Prog parameters sequence and
programming of VFD
B,ock diagram of basic PLCSystem ,Different types of I/P & O/P,PLC
Programming,Instruction set.
Connection of drive with PLC and control
Connect and test the VF drives.
Connect VFD with various control ,programming device
Connect the drives with PLC and test for variousb application.
Tool List Inverters, UPS ,Voltage stabilizers and Industrial drives:
Sl No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Description of Items
Crimping tool set
Spanner set DE, Ring
Screw drivers assorted size
Soldering Iron 65w
Neon Testers, 500V
Combination Plier
Loose Nose plier
Diagonal cutter
Neon Tester
Screw driver set
Electrician Knife
Allen key set
Steel rule
Hammer
Mallet
Hand Shear metal cutting 25 cm
Electric drilling machine portable 10mm
File flat 200mm 2nd cut
Tri square
Instrument file set
Bench vice 200mm
Qty
4
2
2 each
2
2
4
4
4
16
16
16
4
4
4
4
4
4
4
4
4
6
10
Equipment List
Sl No
Description of Item
Inverters 500VAwith suitable batteries
,Inverter 1KVA, 3KVA with suitable batteries
OFF – LINE UPS 500VA, 1KVA, 3 KVA
ON-LINE UPS 5 KVA
Inverter 3 phase 3 KVA
ON-LINE UPS, 3 phase, 3 KVA
Clip on Meter – digital
Power supplies 0-30V, 5A
Multimeter 20Meg, 20 Amps AC/DC
Watt meter 10A
Earth Megger
Multimeter Digital
Dual power supply 0-30V, 2A
CRO, 50 MHz, Dual Trace
Function Generator
Battery charger
Line Interactive UPS
Discharge Tester
1 KVA & 2 KVA automatic Voltage Stabilizers
1KVA,2 KVA & 5 KVA Servo Controlled Voltage stabilizers.
Servo Stabilizer Trainer
Basic Electronics Trainer
Power Electronics Trainer
Microcontroller Kit along with add on cards DAC,ADC,Stepper Motor
DC shunt motor 5 HP,1500 rpm
DC Compound motor 5HP,1500 rpm
AC 3 phase Induction motor,7.5 HP Squiril cage
AC 3 phase slip ring Induction motor
3 Pt & 4 Pt starter
Brushless DC Motor
Universal motor
Qty
4
1 each
1 each
1 each
1
1
2
2
4
1
2
1
2
2
2
1
2
1 each
1 each
1
2
2
4
1
1
1
1
2 each
1
2
11
Single phase Transformer, 3 Phase transformer
DC drive/ Trainer using phase control, PWM
Variable Frequency Drive/Trainer
Trainers of various sensors -Hall sensor ,Magnetic sensor,tacho
generator,Opto-couplerwith complete set up
PLC system
Open loop & Close loop speed Control Trainers for AC motor and test setup
compatible with PLC system
2
1 Each
1 No.
1
1
1
12
Advanced Module of Electronic Sector
MODULE- 3
Repair & Maintenance of Electronic test equipment:
Theory
Introduction to various Electronic Test Equipment
Review of passive Electronic components ,their specifications
and applications:
Resistor ,Capacitor ,Inductor Transformers, choke coils,
various switches
Review of active components:
Diode , precision rectifiers ,Transistors , LED, FET,
MOSFET, SCR ,TRIAC and DIAC,OP-AMP
Review of Basic Logic gates ,TTL and CMOS Integrated
circuits
Logic Tester/Logic Clip: Use and working of Logic tester and
Logic Clip
Microprocessor : basic architecture , programming, (8 bit)
interfacing , DMA
Microcontroller : basic architecture , programming, (8 bit)
interfacing , DMA
Practical
Familiarization with:
Analog Multimeter ,Digital Multimeter, Function Generator
Oscilloscopes ,DC Power Supply ,LCR Bridge ,Sine & Square Wave
Oscillator ,RF Oscillators (Signal Generators)
Digital IC Tester ,EPROM Programmers Universal programmers
Identification of components:
Resistor – Value & Wattage , Finding value from colour code
Wattage .
Capacitor-Type of capacitors, Polarized & Non-polarized capacitors, Reading
value, working voltage & tolerance of a capacitor
Transformers & coils-step down and step up transformer, Air-core coil ,Ironcore coil ,Ferrite core coil
Variac
Identification of Diodes: Types of Diodes, Identifying the anode & cathode ,
Identification of transistor : Types of transistors – NPN/PNP Lead
identification (EBC),Signal transistors, Medium power transistors & Power
transistors
Identification and testing of : N channel & P channel FET, ,MOSFET-IGBT ,
UJT, SCR , TRIAC & DIAC
Testing and use Linear Ics-Op Amps & Comparators
Testing of TTL and CMOS IC
Identification and use of Logic Tester and Logic Clip
Execution of program instruction on 8085
Execution and testing of program instruction on 8031/8051 Micocontroller.
Testing Memory IC ,Testing Peripheral IC, Testing of Microprocessor -Testing
IC in Step mode ,Testing IC in HUNT mode ,Interfacing IC Tester to a PC
13
Memory classification , Memory Ics-RAM, ROM, EPROM
Study of EPROM Programmer :
Specifications and block diagram , Introduction to EPROMS
Operation of a EPROM programmer , Circuit description (in
brief)
Study of Universal Programmer – PC Interface :
Specifications and block diagrams , Interfacing programmer to
a PC
Study of Analog Multimeter :
Block diagram & specifications, Construction of moving coil
meter (PMMC),DC Voltage measurement circuit
AC voltage measurement circuit ,Resistance measurement
circuit ,DC Current measurement circuit
Study of Digital Multimeter :
Specifications , Block diagram ,Displays – LED, LCD
Introduction & methods used for Analog to Digital Converters
(Dual slope A/D converter)
IC used in DMM for A/D conversion for 3 ½ digit & 4 ½ digit
IC 7106 ,IC 7107, etc.
Circuit description of (a) DC voltage measurement (b) AC
voltage measurement, (c) DC current measurement ,(d) AC
current measurement (e) Resistance measurement.
DMM Trouble shooting and calibration procedure.
Study of CRO :
Specifications and block diagram , Familiarization with front
panel and controls of a CRO.
Study of CRO circuits (a) Vertical preamp (b) Vertical
Intermediate amplifier (c) Vertical Final amplifier (d) Time
base circuits, (e) Horizontal Final amplifier (f) Low voltage &
EHT power supply circuits.
Study of H V circuits
Digital storage and IEEE interface of a oscilloscope.
Trouble shooting procedure of a CRO.
Study of Function Generator :
Specifications & Block diagram , Study of circuit used in
Familiarization with an EPROM programmer- Front panel controls, switches
& displays
Using program perform :
Read , Blank check , Burn ,Verify
Installing the universal programmer with a PC
Selecting the device to be programmed
Programming various devices using programmer
Construction of moving coil meter movement ,Circuit tracing & identifying
components of (a) DC voltage measurement circuits (b) AC voltage
measurement circuit (c) DC current & (d) Ohms/Resistance measurement
circuit
Doing measurement using DMM & checking its performance on
DC Voltage ,AC Voltage, DC mA, AC mA, & Resistance measurement
ranges.
Opening a Digital multimeter and identifying the components used in it.
Testing the display : LED , LCD type displays.
Identifying and tracing circuit related to A/D converter & other section’s & its
trouble shooting.
Testing the performance of DMM using standard/calibrator.
Doing measurement using CRO – Measurement of DC Voltage, AC voltage,
Period & Frequency & observing voltage and wave form measurement.
Troubleshooting CRO Vertical Preamplifier & all other sections (a) to (f).
Familiarize and doing measurement using Digital storage oscilloscope
Interfacing DSO with a PC (IEEE)
Familiarization with front panel controls of a Function Generator
Opening a Function Generator and identifying the components used in it ,
14
Function Generator using:
(a) Descrete components and (b) custom built ICs (Function
Generator (ICs)
Microprocessor / Microcontroller based Functiongenerator
Trouble shooting on function generator
Study of LCR Bridge :
Specifications and Block diagram , Types of Bridge – DC &
AC , Circuits used. LCR-Q Bridge with Auto-compute
facilities.
Study of a Sine , Square wave Generators & RF signal
Generators :
Specifications & Block diagram , Circuit operation
Circuit tracing and identifying circuit as per block diagram , Voltage &
waveform measurement at different section of a Function Generator
Testing the performance of it
Familiarization with front panel and controls of a LCR bridge and
measurement of
Resistance , Capacitance , Inductance 7 Q.
Familiarization with front panel & control of a Sine wave, Square wave and
RF-Signal Generator generator
Observe and study the output waveforms of a sine and square wave generator
using CRO
Observe and study the output waveforms of a RF-Signal Generator using CRO
Familiarization with different types of Power Supply
Study of Power Supplies :
Testing Power Supplies as per its specifications :
specifications & block diagram , Linear power supplies
a) Line Regulation ,(b) Load Regulation (c) Ripple
Fixed output voltage , Variable output voltage (adjustable
Assemble , test and fault finding in IC regulators
output) , Power supply using 3-pin IC regulator-Circuit
Identification of different section of SMPS
description
SMPS -Specifications and block diagram & Circuit description Assemble, test and fault finding of SMPS
Familiarization with front panel controls and display system
Study of a Digital IC Tester :
Testing of : TTL , CMOS ,Memory ,Peripheral Ics
Specifications & Block diagram , Operation and circuit
Testing of Microprocessor
description of of a Digital IC Tester
Familiarization with front panel controls and display system
Study of a Linear IC Tester ;
Testing of OP-AMP,Comparators
Specifications and block diagram , Operation of a Analog IC
Tester and its Circuit description (in brief)
Identify various parts/ section , controls and features of
Specification & block diagram of Special equipment : Pattern
Pattern Generator , Logic Analyser, Microprocessor based Recorder, IEEE
Generator, Logic Analyser, Microprocessor based Recorder,
interface Multimeter, Spectrum Analyser , Frequency counter , Barcode
IEEE interface Multimeter, Spectrum Analyser, Frequency
reader.
counter ,Barcode reader
15
Repair & Maintenance of Electronic test equipments Equipment List :
Sl No
1
Description of iItem
Tool Kit
Digital Multimeter
Analog Multimeter
Basic Electronics Trainer with bread board facility
Power Electronics Trainer with bread board facility
Digital IC Trainer(TTL & CMOS) with bread board facility
Linear IC Trainer with bread board facility
Logic Clip
Logic Tester
8085 basedMicroprocessor Trainer kit(8 bit) with peripheral study boards
8031 based Microcontroller Trainer Kit (8bit)
EPROM programmer
Universal/PAL programmer
Digital Multimeter Trainer.
20 MH Oscilloscope Trainer
Function generators with different O/P
LCR bridge
RF/AF signal generators Trainer
Power supplies 0-30V variable regulated DC
IC based Power supply 5V,12V-1 Amp
SMPS Trainer 5V/12 V
Color pattern generator
Logic analyzer
Microprocessor based recorder
IEEE interface Multimeter
Frequency Analyser
Barcode reader
Qty
16
16
8
4
4
4
4
4
4
4
4
2
2
2
4
8
2
2
8
8
2
1
1
1
2
1
1
16
Advanced Module of Electronic Sector
MODULE- 4
Automobile Electronics
Theory
Hand tools, various tools;and their specific uses.
Automobile engine –IC engines, two stroke, 4 stroke diesel
and petrol engines.
Functions of carburetor – atomization , speed control of petrol
engine, idle speed and max. speed .
Fuel pump used in diesel engines. Speed control of Diesel
engines.
Multi cylinder petrol engines – firing order, power
development, speed governing methods used in petrol engines.
Multi cylinder diesel engines – firing order, power
development, speed governing methods used in diesel engines.
Auto alternator/Dynamo – its working principle, advantages of
alternator, rectifier circuits.
Description of the wiring circuit, head light circuit, parking
light, penal instrument, fog light circuit
Description of brake, tail and reverse light, flasher light,
working, assembling/disassembling and testing of horn
Working of wiper motor, central lock and power window,
flywheel magneto
Working of Solenoid switches, panel meters, fuel and
temperature gauges
Electronic ignition system, capacitor discharge type, thyristor
type, contact less ignition systems. Spark gap, adjustment of
point gap, spark advance mechanism, centrifugal advance
mechanism, vacuum advance mechanism.
Introduction to Microcontrollers,architecture,interfacing ,
functioning & its application in auto control, Familiarise with
Practical
Familiarise with the hand tools.
Identify and familiarise with different engines.
Familiarise with the internal parts and working of a carburetor and Fuel
pump.
Familiarise with the petrol engine parts and its working
Familiarise with the diesel engine parts and its working
Testing of alternator/dynamo, rectify the faults in rectifier circuits.
Trace wiring circuit, head light circuit, parking light, panel instrument, fog
light circuit
Trace brake, tail and reverse light, flasher light, disassembling & assembling
and testing of horn
Disassemble wiper motor, central lock and power window, flywheel magneto
and test for proper function
Trace the locations, circuits and disassemble/re-assemble the Solenoid
switches, panel meters, fuel and temperature gauges
Test and rectify the fault in electronic ignition systems.
Testing the microcontroller, circuit components and accessories.
Tracing the location of sensors, actuators and transducers and test for proper
17
the interfacing circuits,
Sensors and Transducers.
function
MPFI system, principle of working, and its functions. Sensors
used for Barometric pressure, Vacuum pressure, air temp. and
Coolant temp.
Sensors used for Vehicle speed, throttle position, crank shaft
position.
ECM – Working of ECM, sensors attached with ECM, testing
procedure of ECM
Antilock braking system – principle and working. Devices
connected in the braking system, safety devices.
Power window – motors and switches used for the power
window. Protective devices used along with the motors.
Power steering. Steering technique – Power steering circuit
and its devices – their working and testing procedure.
Trafficators – devices and circuits of trafficators, their
connection.
Car radio – noise suppression system, antenna, car stereo, their
connections, car tv, mobile charger and other accessories –
their connection.
Electronic door locking system, its installation and its working
principle. Remote key system.
Indicators – temperature, fuel, RPM their principle and
working.
Test and the various pressure sensors for their proper working.
Test the sensors of Vehicle speed, throttle position, crank shaft position for
their proper function.
Test the ECM and other connection for the proper function and performance.
Test the antilock brake system and its associated circuits.
Test and repair the power windows.
Test the power steering circuit and devices.
Fault finding in trafficators.
Installation of Car radio, stereo, mobile charger etc…
Familiarise with the connections of electronic door locking systems.
Trace and rectify the faults in the indicator circuits.
18
Automobile Electronics Equipment List :
Sl No
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
Description of Item
Rule Steel 300mm
Chisel cross cut 200mm x 6mm
Hammer Ball Peen 0.5 Kg
Hammer copper 1 kg. with handle
Hack saw frame for 30 cm blade
Hand Vice 37mm
Screw Driver, Electrician type 15cm size
File flat 35cm bastard
File flat 25cm second cut
Soldering iron 120 watts
Clip on Meter Digital
Steel Almirah 180 x 90 x 50 cm
Tachometer
Tester sparking plug “NEON” Type
High rate discharge tester
Battery charger
Multimeter digital
AC alternator slip ring puller
AC alternator slip ring press tool
Executive Auto Electrical Tool kit
Distributor tester
Electrical test bench
Alternator regulator tester
Car stereo
Hydrometer
Vehicle Euro 2 & 3
Enginer scanner
2 stroke & 4 Stroke petrol engine
2 stroke & 4 stroke Diesel engine
Multi Cylinder Petrol engine
Multi Cylinder diesel engine
MPFI system
Car Radio and stereo system
Car locking remote system
P IV Computer system
Qty
4
4
4
4
4
4
8
4
4
2
2
2
2
2
2
2
4
2
2
4
4
4
4
2
2
1 each
1
1 each
1 each
1
1
1
1
1
4
19
Advanced Module of Electronic Sector
MODULE- 5
Communication System :
Theory
Interoduction- Telephone network, Duplex, Susbscriber’s
loop,Signaling Tones, DTMF dialing, Pulse Dialling, Dial
tone, Ringing tone, Busy tone, Number Unobtainable tone
Call in Progress tone
Modulation theory & circuit- Amplitude Modulation,(AM)
DSB/SC, AM-SSB and their comparison ModulationPAN,PDN, PPM, PCM, Delta modulation and Circuits.
Principles of Multiplexing of DM & TDM , frequency
generation and Synchronization circuits
Block Wise Description- Polarity Guard, Ringer Section,
Speech , Different tones – Dial, Ring, Busy, etc.
Dialer Section- Stage Wise Circuit Description for different
brands & models .
Practical
Identify ingTelephone line, Rosset Box connections Demonstration of different
types of Electronic Push Button Instruments(EPBT) and Identifying external
Controls and their applications. Determining difference between different
tones.
Assemble,test the PAN,PDN, PPM, PCM, Delta modulation
Trace the various signal O/P using CRO
Identify and Trace the Circuit for different Stages. Ringer, Speech, Dialar, etc.
Trace Signal Path, Different tones – Dial, Ring, Busy, etc.
Measure Loop Current, Measure Line DC Voltage, On Hook/ Off Hook AC
Line Voltage Measurement and Trace Signal Wave Shape in Ring Mode at test
Ringer IC input and output
Fault Finding Methods-By Voltage measurements, by Wave Measure DC Voltages of Speech IC & Ringer IC Trace Signal
Wave Shape in Speech Mode at IC, Signal Wave
Shape Tracing and by Signal Injecting Methods in different
Shapes in Pulse Mode and Tone Mode at Test Points, Receiver and Transmitter
make/brand instruments
( Mouth and Hearing Piece), Crystal Frequency Measurement with Frequency
Counter/Oscilloscope
IP Phones, Caller ID, Coin operation, Play phones, working
Stage Wise Simulated fault finding with the help of different fault finding
principle
methods, signal injecting, signal tracing and voltage measurement
Identifying different input and output sockets, controls, Operating CLT for
Introduction- Cordless Telephone Base Unit and Hand Set
Different settings on base unit, Programming calling numbers, and getting
Technical Specification-Block Wise description, IC’s Pin
familiar with other controls on base unit/hand set
description, function, types of data cables-mobile phone
Dis-assembling CLTinstrument-Identifying SMD components, different
circuits
stages circuit tracing
Voltage measurements-Opto-cupler for ring detecting, Voltage Charger, CPU
Functional description of Base Unit –Opto-cuplar working
at ring or no ring, receiver & transmitter voltage controlled oscillators ,
Principal for detecting ring signal ,
Functional description of CPU for signal detection, coupling, Frequency measurements-receiver & transmitter sections of Base Unit & hand
20
Signal, Battery Charge detection and other application
set.
Base Unit, Hand Set receiver and transmitter RF signal and
their frequenciesprocessing-Multiplexing, Modulation,
Power amplification and transmission, Signal receiving and
demodulation process
Types of faults and their remedies
Introduction- Public Switching Telephone Network
(PSTN),Central Office Line, DTMF, Subscriber, Signaling,
Switching1 EPABX Standards- Stored Program
Control(SPC), Space Switch, Time division multiplexing
Tracing wave shapes with the help of Oscilloscope at different test points.
Different stages in base unit and hand set Tx and Rx frequency settings ,
Types of EPABX- ANALOG & Digital
Block diagram of digital exchange- MDF, SLIC, Trunk Line
interface, CPU, TDM switching, Power Supply
Configuration of an EPABX
Architecture & Interface- SLIC, co LINE , TGU, CPU, Main
Distribution Fram & Power supply
EPABX System Features- direct outward dialing, Paging,
Line Networking, Call privacy, line out of service, direct
inward dialing, emergency
Extention Features- Extension to CO line, Local call, STD
ISD,
Extension to Extension call, Extension to tie line, Automatic
call back-busy, call forward & etc.
DC voltage- Source, Distribution and cabling
Mobile phone- introduction, user guide,
Mobile Phone Circuits Diagrams,
Mobile phone System -TDMA, GSM, CDMA
Identify- Time Division Multiplexing & Demultiplexing , TDM pulse
Modulation & demodulation
Mobile Phone Programming (Service Software Operation)
Mobile phone data cable computer interface diagram
Mobile Phone data cables, dissembling procedure,
SMD Resistors, Diodes, Coils, Filters, Capacitors,
Transistor,Crystal, Modules, Integrated circuits.
Mobile units- Power supply, data processing, Display
Simulated faults finding in Base unit and Hand set
Identifying different stage- Speech Circuit ,DTMF
& Pulse Dialing Circuit. Dule tone ring generating,
Subscriber line & switching digital circuits, Ring & Tone Generator & it’s
interface
Data Coding Techniques &Phase Encoded format, Amplitude Shift Keying
&Frequency Shift Keying,
Phase Shifting Keying Techniques
Delta Modulation & Demodulation, Adaptive Delta Modulation Demodulation,
Compander , Expander, & Voice communication, Structure Configuration
Hardware & software setup of the ISDN
Different brand of cell phones-NOKIA, SAMSUNG, LG, MOTOROLLA,
SONY, PANASONIC, NITSUBISHI, SIEMENS, etc.
Identifying different components-Resistors, Diodes, Coils, Filters, Capacitors,
Transistors, Crystals, Modules, Integrated Circuits
Mobile unit Power supply, Data processing, Display
Section, Audio Section., dialing section
Circuit Tracing, Basic training, circuit reading, MIC, LED, Key pad, Speaker,
Buzzer, On & Off switch, Display, Antenna, Charging pin, PCB circuit
SMD technique Mobile spare parts and installation technique, Online
21
section,Audio section, dialing
Work shop technique, Servicing technique,
Study of Mobile Software and its installation
Software problems and solution. Fault finding with
Software.
Inteduction to GSM, SIM Cord Recorder, Advance Mobile
Phones.
Understanding and designing of Fibre OPTIC Analog
Transmission system : fundamental of fibre optics, properties
of Transmission & Receiver, charectarization of fibre optic
cable, fibre optic intensity modulation system for Analog
Transmission & frequency response
Understanding and designing of Fibre OPTIC Digital
Transmission system : fundamental of fibre optics,properties
of Transmission & Receiver, charectarization of fibre optic
cable, design and study of Fibre optic Digital link,rise and
fall time distortions, propagation delay and data
transmission, CRT terminal interface and communication
parameters.
Basics of Microwave communication system - Frequency
spectrum , Microwave generation-Gunn diode, Klystron
Wave guides,Transmission and reception of Microwave
signal, repeater stations, propagation
component testing, Input and output supply, checking 15 testing points
Testing points of mobile circuits mobile problems and solution,
Fault finding sequence , hardware problems and solution
Mobile software installation, Software problems and solution flashing
Identify and study the Transmitter, Receiver, Sinewave generator, optical fibre
cable-parameters in Fibre optic Analog Transmission system , Intensity
modulation and demodulation system .
Identify and study the Transmitter, Receiver, TTL square wave
generator,optical fibre cable-parameters in Fibre optic Digital Transmission
system , Design and study the - Fibre optic digital link, Rise time & Fall time
distortion, propagation delay
Assemble and test the Microwave signal using Gunn diode, Klystron,
Transmission and reception of signals
22
Communication System Equipment List :
Sl No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Description of Items
Different type and brand telephone instruments
Different type and brand cordless telephone
Different type and brand cell phones
Mobile Trainers
EPBAX Trainer
EPABX exchanges
Telephone Analyzers
Personal Computers P IV system
Different brand cell phone data cable
Digital Multimeters
Oscilloscopes 100 Mhz.
Dual trace with LCD display
Frequency counters
UPS 500 VA
GSM SIM Cord Reader
Camera Phones
Coin Operated Phones
Cell Phone Test Jig
DC Regulated Power Supply 0-30V, 1 A
Temperature controlled soldering stations
SMD rework stations
Precision Screw driver sets
Multipurpose Screw driver sets
Magnifier Lens 10 X with lighting
Micro Soldering Irons with different tips
Tool kit suitable to syllabus equipment
Analog Fibre Optic Trainer
Digital Fibre Optic Trainer
Wave guides
Microwave generation Trainer
Qty
4 each
2 each
2 each
2
2
1
1
4
2
4
2
1
4
1
1
1
2
2
5
1
6
16
2
4
16
2
2
2
2
23
Advanced Module of Electronic Sector
MODULE- 6
Embedded system and PLC :
Theory
Introduction to basic Computer architecture ,CPU & its
spcification.
Accumulator & Register based processors
Microprocessor an overview of 8 bit (8085 )Processor,
architecture , Interrupt system, Mapping & DMA, Basic
programing concept-Assembler, flowchart, debugging.
Addressing modes , types of instructions, Instruction set
Comparison with other 8 bit processors.
Microprocessor and Microcontroller- a comparison
Mocrocontroller an over view of 8051 & its Architecture,
Instruction set, Addressing modes, Programming-Data Transfer,
Arithmetic, Logic, Boolean Variable manipulation & branching
Instruction
I/O ports pins and their functions, I/O
Programming, Bit manipulation ,Timers, modes of Timers,
application of Timer to generate Time Delays.
Interrupts and polling, various interrupt SFR’s related to Interrupt
Programming
Edge Triggered and level triggered interrupts Priority of interrupts
Difference between serial and parallel Communication ,serial
communication protocal, synchronous and
Asynchronous communication, Data Framing, RS232 Standard,
max 232 chips
Baud Rates, programming Techniques.
Various methods of A to D & D to A conversion-counter type
ADC, Successive type, Integrating Type ADC’s
Specification of DAC & ADC,
8255-programmable peripheral device,
Concepts of Traffic light control, Fundamentals of Stepper motor-
Practical
Familiarization of MP kit
Program Execution using - Data Transfer Group,Logic Group, Arithmetic
Group Branch Group
Interface microprocessor kit with different application boards and run the
applications
Familiarization of MC kit
Program Execution using -Data Transfer Group, Logic Group, Arithmetic
Group, Branch Group
Study of interfacing techniques
Hard ware and software
Exercises in ports &
Read the status of a switch using MC port pin
Drive a relay using MC port pin
Develop & run programs using Timer, Counter & Interrupt applications
Transmit & Receive Data with PC using serial link, Connection of
Microcontroller kit to PC
Interfacing of MC using 8255 and study the working of:
Traffic light controller ,DAC, ADC, Stepper motor ,Elevator,
LCD KEYBOARD
24
types, driving methods, Elevator ,Key board and LCD
Introduction to C Language, Constants, variables and Data Types,
Operators, Expessions, Input & Output operators, Decision
Making and Branching, Looping, Array, Chracter Strings, User
Defined Functions, Structures & Unions, Pointers, Classes in C++
& Stack operationsrrtrt
Introduction to PIC MC, Architecture, Instruction set, Additional
Features
Network features-Network topologies,protocolsTCP/IP,UDP/FTP,models, types, components,network medias,specification and standards,types of cables
Difference between PC & Server,
Server-Usages of Server ,Types ,Server hardware,
Operating system-OS ,NOS-features,types
Architecture of 16 bit (8086 )processor, Basic programing
concept-Assembler, flowchart, debugging .Addressing modes ,
types of instructions, Instruction set , Comparison with other 16 bit
processors.
Evolution of different control techniques like manual, hardwired,
electronic gate control and programmable control. Advantages and
disadvantages of different techniques mentioned above.
Different type of analog and digital input and output field devices
used in process industries. Types of voltage and current formats
used in field devices. Types of connections of field devices to
controllers.Type of cables used for connecting field devices to
Basic structure of c program
Execution & compiling c program
Program with -various data types ,using mathematical operators
Program with input & output operations
Program with simple loops & using 2D array, multidimensional arrays,
character string& user defined functions
Exercise on PIC MC
Identify physical topology of a network and
members of the network ,identify the protocols installed and check
resource sharing
Identify the cables and components in the network
Identify controls and ports on servers
Identify the hardware of servers and configuration
Starting and shutting down servers
Identifying and using basic features Using Win 2000
Prof/Linux/Unix/Novell features
Making UTP cross cables and testing ,Making straight cables and testing
,Making cable layout drawing
Installing information outlet points.
Install different common protocols one bye one and test communication
and features
Install and check TCP/IP utilities and services
Program Execution using Kit and PC
Study of interfacing techniques
Identification of different digital input and output field devices used in
process/ mechanical industries categorized w.r.t voltage levels, single end
and differential end etc. Operate and test the above mentioned field devices
Identify different type of cables used to connect field devices to closed
loop single/multi loop controllers and programmable controllers. Identify
different cables and connectors used to connect programming terminals
such as HHT, PC etc to the programmable controllers.
25
controllers.
Block diagram of a basic PLC system and the Architecture, PLC
components principles of working of PLCs, Specifications of
PLCs.
Different type of modules like Digital and Analog input and output
modules and their working Hardware description of I/O, power
supply Modules I/O addressing concepts. Types of memory used
in PLCs. Memory and its impact on performance of PLC Memory
map and Data files used in PLCs Different functional blocks/files
and their uses
Different industry Bus communication standards like RS232, RS
422, DH, DH+, 485 etc and their charac-teristics. Different type
protocols used in the field of PLCs. Programming of PLCs using
different techni-ques such as Ladder, Instruction list, Control
system flow chart etc.
Instruction set covering basic I/O operations, timer, counter, data
copy, arithmetic Logical, compare type, program control, shift
instructions etc., PLC interrupts, PLC subroutines, PLC
sequencers.
Wiring, entering, documenting and testing program.
Types of special function modules such as memory module, high
speed counter, Communication processor module and its
importance.
Introduction to SCADA and DCS system
Identify the CPU type and the memory inside.
Identify typical modules of the given PLC systems (such as power supply,
Digital and Analog I/O(signal modules), basic module, high speed module,
special function modules, RTD/Thermocouple etc)
Identify the type of connectivity between the CPU and different. Modules
of PLC. Identify the type of communication between different modules
with PLC.
Common faults in a typical PLC- based system with respect to
hardware i.e power supply, digital/analog I/Os, special function
modules, communication modules etc. Diagnostic capabilities of
the PLC Software and the typical codes generated by the system
for the effective troubleshooting of different modules of PLCs
Wireless communication standards & various types of networks
Familiarization and interpretation of the screens and its contents provided
for diagnostic purpose in the software. Interpretation of the error codes.
Clearing the minor errors and major errors. Troubleshooting screens.
Install the PLC Software on the PC. Configure
the
software
to
communicate with a PLC.
Familiarization with the software and use of
different Data files/ function blocks etc. Develop simple programs and
Download them for execution for simple digital I/O Develop programs
using timers and counters and execute. Develop programs to cover
different instructions and execute.
Develop and run simple tasks such as control of a relay,
contactor,
lamp & motor etc for different input conditions. Monitor the status of the
application ONLINE. Perform some Force operations. Develop programs
to acquire analog data using Analog input card. Develop programs to
display/control data using Analog output card. Make a closed loop control
system using analog I/Os and control
a process.
PID
Control
using PLC. Interrupts using PLCs. Sub-routine development in PLCs.
Repeat all the above for any two popular commercial PLCs.
Exercise on wireless
26
Embeded system and PLC :Equipment List
Sl No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Description of Item
8085 based Microprocessor Kit
8051 Based Microcontroller kit
Interfacing Modules such as DAC,ADC,TRAFFIC LIGHT ,STEPPER MOTOR,LCD
Display & Key board
8086 based 16 bit Trainer Kit
Pic Microcontroller Kit
P IV Computer Server configuration
P IV Computers
Compiler on C language
Window 2000 software
8 Port Hub
NIC cards,cables and peripherals
Bread Boards
Microcontroller Programmer
Components (MC, Memories,Resistors, cap, wires ETC)
Soldering Iron (Temperature Controlled)
PIC programmer
In-circuit emulator
Oscilloscope (100MHZ)
Digital Mulitimeter
PLC Trainer Systems ( SIEMENS & ALLENBRADLEY )
PLC development software for Siemens & Allenbradley PLC systems.
Working models for PLCs
a) Bottle fill trainer
b) Speed control module
c) Batch process reactor
d) Start delta starter
e) Discrete application trainer
SCADA software
Hand held programming terminal for PLC
Qty
4
4
4 each
4
4
1
4
1
1
1
4
2
1
As required
6
1
1
1
6
1 each
1 each
1
1
1
1
1
1
1
27
30
31
32
Miniature type lab compressor with necessary accessories
Sensors: Thermal, Optical, Pressure, Flow, Position, Motion etc.
Different types of Electronic push buttons (NC & NO ), toggle switches, valves , relays,
solenoids valves
Variable DC Power supplies 0-30 V
Dual trace oscilloscope 20 MHz
Online UPS (5 KVA)
OHP
LCD Projector
Printers Laser jet
Scanner A4
Air-conditioner 1.5 Tonn
Laboratory tools
33
34
35
36
37
38
39
40
41
1
1 each
1 each
2
2
1
1
1
1
1
3
As required
SPACE REQUIREMENTS
1)
Classroom
-
2)
Laboratory
-
1 No.
100 Ft.
30 Ft
28
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement