PVS8372 IB MTK DRC6317E English.indd

PVS8372 IB MTK DRC6317E English.indd
Important safety instructions
user manual
DRC6307E
AVC Multimedia
Markham, Ontario L3R 1E3
http: //www.RCAav.com
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block the ventilation openings. Install in
accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. D o n o t d e f e a t t h e s a f e t y p u r p o s e o f t h e
polarized or grounding - type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade or
the third prong are provided for your safety. If
the provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specified by
the manufacturer.
12. Use only with a cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
1.
2.
3.
4.
5.
6.
7.
Read these instructions before using your new product for the first time.
Disc formats
Safety precautions
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as the powersupply cord or plug is damaged, liquid has
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or
moisture, does not operate normally, or has been
dropped.
DVDs
[8cm/12cm disc]
Audio CDs
[8cm/12cm disc]
* SEE BOTTOM OF UNIT FOR GRAPHIC SYMBOLS *
WARNING:
Should any trouble occur, disconnect the AC power
adapter and refer servicing to a qualified technician.
Do not use the unit in places that are extremely hot, cold, dusty, or humid.
Place the unit on a flat and even surface.
Do not restrict the air flow of the unit by placing it in a place with poor air flow, by covering it with a cloth,
or by placing it on carpeting.
To avoid magnetizing, do not place the unit near speakers or magnets.
Do not use this unit in direct sunlight or leave the unit in a closed automobile, etc., where it would be
exposed to high temperatures above 104°F (40°C).
No naked flame sources such as lighted candles should be placed on the AC power adapter or the main unit.
The apparatus should not be exposed to splashing or dripping liquids, and no objects filled with liquids,
such as vases, should be placed on apparatus.
•
•
•
•
•
•
•
On safety
When connecting or disconnecting the AC power adapter, grip the plug and not the cord itself. Pulling the
cord may damage it and create a hazard.
When you are not going to use the unit for a long period of time, disconnect the AC power adapter.
•
•
On condensation
When left in a heated room where it is warm and damp, water droplets or condensation may form inside the
unit. When there is condensation inside the unit, the unit may not function normally. Let the unit stand for 1
to 2 hours before turning the power on, or gradually heat the room and allow the unit to dry before use.
•
Unit
Region Management Information: This unit is designed and manufactured to respond to the Region
Management Information that is encoded on DVDs. If the region number printed on the DVD does not
correspond to the region number of this unit, it cannot play that disc.
•
Do not block the ventilation openings or holes. If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to get out.
Do not operate the unit in a confined space, such as a bookcase or built-in cabinet. Allow about 4 inches
(10cm) of free space all around the unit for adequate ventilation.
Rating plate location
•
The rating plate is located on the bottom of unit.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Notes on copyright
It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, or rent copyrighted material
without permission.
Apparatus Claims of U.S. Patent Nos. 6,836,549; 6,381,747; 7,050,698; 6,516,132 and 5,583,936 licensed for limited
viewing uses only.
This product incorporates copyright protection technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and
is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
Remote control
Remote Control (with battery)...............................................................................................................................................x 1
AC Power Adapter.......................................................................................................................................................................x 1
Car Power Adapter......................................................................................................................................................................x 1
Region management information
•
Control reference guide
Please check and identify the supplied accessories.
Compatible
This product contains a
low power laser device.
On placement
The lightning flash with an arrowhead
symbol, within the equilateral triangle, is
intended to alert the user to the presence of
uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to
cause an electric shock.
The exclamation point within the equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in this owner’s
manual.
Ventilation warning
FCC statements
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
Accessories
This unit can play
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DO
NOT PLACE OBJECTS FILLED WITH LIQUIDS ON OR NEAR THIS UNIT.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR
EQUIVALENT TYPE.
1. VIDEO MODE button
9
Adjusts Brightness, 1
Pa n e l D i s p l a y a n d 2
10
3
Contrast of the LCD
4
11
screen.
5
PREV button
2.
12
M
6
Moves back through
13
14
titles, chapters or
tracks on a disc.
15
7
3.
/
SEARCH
buttons
8
S E A R C H : Fa s t
reverse playback.
S E A R C H : Fa s t
forward playback.
4. GOTO button
Skips directly to a location on a DVD.
5. Cursor ( , , , ) buttons
Moves between selections on a menu screen and adjust
certain settings.
ENTER button
Confirms selections on a menu screen.
6. MEMORY button
Sets titles/chapters/tracks in a favorite order.
7. Number (0 - 9) buttons
Use when creating programs or locating a title/chapter/
track or specific time.
8. REPEAT A-B button
Performs point-to-point repeat playback on a DVD or CD.
REPEAT DISC button
Repeats a DVD chapter or title.
Repeats a CD track or the whole disc.
VIDEO
MODE
MENU
PREV
SEARCH
GOTO
NEXT
STOP
PAUSE
ANGLE
DISPLAY
PLAY
ENTER
The region number of this unit is 1.
MEMORY
AUDIO
Disc function or operation that is not available
When the symbol appears on the screen, it indicates the function or operation attempted is not available at that
time. This occurs because the DVD manufacturer determines the specific functions of DVDs. Certain functions may
not be available on some DVDs. Be sure to read the documentation provided with the DVD.
Icons used on DVDs
Language selections for audio
Sample lcons
Language selections for subtitles
Note:
When playing back a CD-G (Graphics) or CD
EXTRA disc, the audio portion will be played,
but the graphic images will not be shown.
1
Remote control
6
Using the remote control
•
•
Multiple camera angles
•
Point the remote control at the REMOTE SENSOR located
on the unit.
When using this unit in very bright light, the infrared
REMOTE SENSOR may not work properly.
The recommended effective distance for remote operation
is about 16 feet (5 meters).
Remove the
PLASTIC sheet
before USING the
Remote Control.
To change remote battery
Battery replacement
1. Open the battery door.
When the batter y becomes weak ,
the operating distance of the remote
control will be greatly reduced and you
will need to replace the battery.
Title1
Title2
DVDs are divided into “titles” and “chapters”. If the disc
has more than one movie on it, each movie would be a
Chapter1 Chapter2
Chapter3 Chapter1 Chapter2
separate “title”. “Chapters” are sections of titles.
• Audio CDs are divided into “tracks”. A “track” is usually
one song on an Audio CD.
Track1
Track2
Track3
Track4
Track5
Note: Numbers identify each title, chapter, and track on a disc. Most discs have these numbers recorded on
them, but some do not.
Notes on unauthorized discs
You may not be able to play some DVDs on this unit, particularly if they were purchased from outside your
geographic area or made for business purposes.
8
9
0
SETUP
•
2. Insert one CR2025 (3V )
size battery.
Note: If the remote control is not going to be used for a long time, remove the battery.
WARNING: Do not dispose of the battery in a fire. It may leak and/or explode.
WARNING: Batteries should not be exposed to excessive heat such as sunshine, fire or the like.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
1.
2.
3.
4.
5.
6.
7.
LCD screen
DC IN 9V-12V jack
AUDIO / VIDEO OUT jacks
CHARGE / STANDBY / ON switch
VOL control
Headphone jack
NEXT button
Advances chapters / tracks.
PREV button
Goes back to the previous chapters / tracks.
PAUSE button
Pauses playback of a disc. Each time you press
the PAUSE button the picture advances one
frame on a DVD.
PLAY button
Starts or resumes playback of a disc.
STOP button
Stops playing a disc.
SEARCH button
Performs fast forward playback.
SEARCH button
Performs fast reverse playback.
8. Disc door
Push to close the disc door.
9. OPEN knob
Slide rightwards to open the disc door.
10. Remote sensor
Receives the remote control unit signals.
11. ON indicator
12. CHARGING indicator
Charge the rechargeable battery before using
it for the first time. The normal charging time
should be completed in approximately 4-5 hours.
The charging light will go out when the battery
becomes fully charged.
Power supply
DISC
REPEAT
Connections
A. Using the AC power adapter
1
To AC power outlet
AC power adapter
Warning:
The AC/DC adapter is used as a disconnect device and it should remain readily operable during intended use. In
order to disconnect the apparatus from the mains completely, the AC/DC adapter should be disconnected from
the outlet completely.
Cautions:
• Use the provided 12V car power adapter only. Use with other car power adapters could damage the unit.
• The 12V car power adapter included with this unit is for its use only. Do not use it with other equipment.
• In the interest of traffic safety, do not operate this unit or view videos while driving a vehicle.
• Make sure the unit is securely fastened to prevent it from falling or flying through the air in the event of an
accident.
• If the inside of the cigarette lighter socket is dirty with ashes or dust, the plug section may become hot
due to poor contact. Be sure to clean the cigarette lighter socket before use.
• After use, disconnect the 12V car power adapter from both the unit and cigarette lighter socket.
C. Using the built-in battery
The unit has a built-in, non-replaceable, rechargeable battery. Charge the built-in battery before using it for the
first time. The normal charging time should be completed within 4-5 hours. The charging light will go out when
the built-in battery becomes fully charged.
To recharge the built-in battery
1
Car power adapter
Turning on the unit
1. Slide the CHARGE / STANDBY / ON switch on the left side of the unit to the ON
position.
2. The start-up picture will appear on the screen.
3. After use, slide the CHARGE / STANDBY / ON switch to the STANDBY (power off )
position.
AC power
adapter
To cigarette
lighter socket
2 To DC IN 9V-12V Jack
Notes:
• When the built-in battery power is low, "Battery Low" will display on the screen and the unit will stop playing.
• Recharge the built-in battery when you are ready to use it again.
• While using the built-in battery, the environmental temperature should be 41°F (5°C) to 95°F (35°C).
• To get the longest service life of the built-in battery, charge at indoor-temperature.
• The built-in battery in this device may present a risk of fire or chemical burn if mistreated. Do not
disassemble, heat above 212oF (100oC), or incinerate.
• The unit should not be exposed to excessive heat such as sunshine, fire or the like.
• When discarding the unit, environmental problems must be considered and local rules or laws governing
the disposal of such products must be strictly followed.
A. Connecting a TV
If your TV has audio/video inputs, you can connect the unit to your TV using standard Audio/Video cables.
TV
White Red Yellow
To AUDIO / VIDEO OUT jacks
Audio / Video cable
(not included)
Watching a DVD on your TV
1. Turn on the unit.
2. Turn on the TV and follow the instructions included with it to play the DVD.
B. Using headphones/earphones
AC power
1 To
outlet
B. Using the car power adapter
Warnings:
• The built-in battery can only be recharged when the unit is in CHARGE mode while using the AC power
adapter.
• The built-in battery cannot be recharged when the unit is in ON mode.
• Do NOT recharge the built-in battery in a vehicle using the car power adapter.
• Batteries should not be exposed to excessive heat such as sunshine, fire or the like.
To DC IN
2 9V-12V jack
•
•
Turn down the volume before connecting, and then adjust
the level.
When headphones/earphones are connected, no sound will
be emitted from the unit's speaker.
Caution:
Avoid listening to sound at levels which may be harmful to your
ears.
Headphones/Earphones
(3.5mm diameter plug)
Warning:
Disconnect the car power
adapter when not in use.
Not for use in 24V vehicles.
the switch
3 Slide
to CHARGE
Recharging is completed
C h a rg i n g
4 light ON
5 when charging light goes
out
White Red Yellow
2
To DC IN 9V-12V Jack
Cautions:
• The AC power adapter included with this unit is for its use only. Do not use it with other equipment.
• When the unit is not going to be used for long time, disconnect the AC power adapter from the AC power outlet.
• When the AC power adapter is plugged in, the apparatus is not completely disconnected from the main
power supply, even when the power is turned off.
The 12V car power adapter
allows the unit to be used
with vehicles that have
a 12V, negative ground
electrical system.
3
5
A-B
Screen aspect ratio
Region code indicator
7
Title, chapter and tracks
The supplied AC power
adapter operates on AC
120V.
2
SUBTITLE/
RETURN
4
SETUP button
In DVD Stop Mode, displays the unit’s
SETUP menu.
9. MENU button
Enters and exits the main DVD menu.
10.
NEXT button
Moves forward through titles, chapters or
tracks on a disc.
11. STOP button
Stops playing a disc.
PLAY button
Starts or resumes playback of a disc.
PAUSE button
Pauses playback. Press subsequently to
advance frame by frame on a DVD.
12. DISPLAY button
Shows status information on the screen.
13. ANGLE button
Switches between multiple camera angles
if applicable to the DVD.
14. AUDIO button
Select one of the audio sound tracks on
a DVD (if more than one is available) or
select the audio output mode on a CD.
15. SUBTITLE button
S elec t one of the subtitle languages
programmed on a DVD (if available).
RETURN button
Returns to normal operation after using
the SETUP menu of a DVD.
Playing a disc (basic playback)
Repeat playback
This owner’s manual explains the basic instructions for operating this unit. Some DVDs are produced in
a manner that allows specific or limited operation during playback. Therefore, this unit may not respond
to all operating commands. THIS IS NOT A DEFECT. Please refer to the instructions accompanying the
specific DVD in question for more information about the options available on that DVD.
“
” may appear on the screen during operation. A “
” means the desired operation is not permitted
by the unit or disc.
Playing a disc
Stopping playback
1. Slide the CHARGE / STANDBY / ON switch on
the left side of the unit to the ON position.
See Customizing the function settings before
proceeding to step 2.
2. Slide the OPEN knob rightwards to open the
disc door.
3. Hold the disc by its sides and carefully place it
onto the spindle with the label side facing up,
pushing gently until you hear a “click”.
4. Close the disc door. It takes a short while for
your unit to load the disc. After loading, the unit
will automatically bring you to the main menu of
the DVD or start playing the DVD.
5. If the unit does not automatically start playing
the DVD, press the
PLAY button.
Press the STOP button at the location where you
want to interrupt playback. To resume playback at
the position where the disc was stopped, press the
PLAY button.
If you press the STOP button twice, the unit’s
memory will be cleared and pressing the
PLAY
button will reset the DVD to the beginning.
Pausing playback (still mode)
Press the PAUSE button. To resume normal
playback, press the PLAY button.
For a DVD, each time you press the PAUSE button,
the picture advances one frame.
Skip (forward / reverse)
Subtitle selection
Angle selection
•
1. While a DVD is playing, press the SUBTITLE
button to display the current language setting,
as shown in the example.
Some DVDs contain scenes that have been shot from a number of different angles. For these discs, the same
scene can be viewed from each of these different angles.
•
•
Press the
NEXT button to advance chapters/
tracks.
Press the
PREV button to go back to current
or previous chapters/tracks.
For an Audio CD, use the number buttons on the
remote control to go directly to the desired track
number.
Audio selection
On some DVDs, the sound is recorded in two or more
formats. Follow the directions below to select the
preferred language and sound system.
1. While a disc is playing, press the AUDIO button
to show the current audio format number.
Audio 1/3:Dolby D 2ch English
Fast forward / Fast reverse
1. Press the SEARCH
or
SEARCH button
when a disc is playing. Each time you press the
SEARCH
or
SEARCH button, the playback
speed changes in the following sequence:
2x
4x
8x
16 x
2x
4x
8x
16 x
2. Press the
PLAY button when you reach the
desired point to resume normal playback.
Notes:
• The DVD player mutes sound and subtitles
during reverse and forward scan of DVDs.
• The fast playback speed may differ depending
on the disc.
2. Press the AUDIO button repeatedly to select the
desired audio format.
Notes:
• If only one audio format is recorded on the DVD,
the number does not change.
• Some DVDs allow you to change audio selections
using the disc menu only. If this is the case, press
the MENU button and choose the appropriate
language on the disc menu.
• You can select different audio channels (Stereo,
Mono Left, Mono Right or Mix-Mono) on an
Au d i o C D b y p re s s i n g t h e AU D I O b u t t o n
repeatedly.
Subtitle 02/03:Spanish
2. Press the SUBTITLE button repeatedly to select
the desired subtitle language. You can turn
subtitles off by pressing the SUBTITLE button
repeatedly until the “ Subtitle Off ” is displayed.
Notes:
• Some DVDs are set to display subtitles
automatically, and you cannot turn them off
even if you set the subtitle function to off.
• During some scenes, the subtitles may not
appear immediately after you select your desired
scene.
• The number of subtitle languages recorded
differs depending on the disc. I f only one
language is recorded, the language does not
change.
• This function can only be used for discs on
which subtitles have been recorded in multiple
languages.
• Some DVDs allow you to change subtitles using
the disc menu only. If this is the case, press
the MENU button and choose the appropriate
subtitle on the disc menu.
1. While you are playing a DVD with different angles recorded,
press the ANGLE button to view the number of current
angles available.
2. Press the ANGLE button repeatedly to change the scene to
the next recorded angle.
• After approx. two seconds, playback will continue from
the new angle selected.
• If no button is pressed within 10 seconds, playback
continues without changing the current angle.
2. While the DVD is playing, press the REPEAT DISC
Title ” indicator displays on
button until the “
the screen. The current title is played repeatedly.
To resume normal playback
Display function
3. While the DVD is playing, press the REPEAT DISC
button until the “ Repeat Off ” indicator displays
on the screen.
While the disc is playing, press the DISPLAY button repeatedly to display information on operation status.
Chapter Elapsed
Tt 01/03 Ch 03/12
0:13:26 Subtitle 02/03:Spanish
Audio 1/3:Dolby D 2ch English
Chapter Remain
Tt 01/03 Ch 03/12
0:05:42 Subtitle 02/03:Spanish
Audio 1/3:Dolby D 2ch English
Title Remain
Tt 01/03 Ch 03/12
0:36:08 Subtitle 02/03:Spanish
Audio 1/3:Dolby D 2ch English
Display Off
Adjust the LCD screen
You can adjust Brightness, Panel Display and Contrast of the LCD screen.
1. Press the VIDEO MODE button.
2. Press the / button to select Brightness, Panel Display or Contrast.
3. Press the / button to change the setting.
4. Press the VIDEO MODE button to exit the menu.
DVD programmable memory
Locating a specific time
If you know the chapter number for the chapter that you want to play, you can locate it by directly selecting that
number.
1. Press the GOTO button.
You can move to a specific location by entering its corresponding time (hours, minutes, seconds).
1. Press the GOTO button two times.
Title 01/03 Chapter 03/12
2. Press the corresponding number buttons (2 digits) for the chapter you want (for example: 02, 08, 10 or 15.
If you press only 1 numeric button, press the ENTER button to confirm).
3. Playback starts from the selected chapter.
Notes:
Input invalid ” will display. You should press
• If the chapter number entered is not permitted by the DVD, “
the GOTO button again and re-enter correct number.
• Some discs may not respond to this process.
• This method of locating a chapter is available only on a DVD that contains chapter numbers.
You can combine your favorite titles/chapters and
play them in the order you determine.
1. Press the MEMORY button while a disc is
playing. The following display appears.
Title 01/03 Time : :
2. Press the corresponding number buttons (5 digits: X:XX:XX, for example: 0 30 05, 1 08 23, 1 22 56) for the
setting point you want.
3. Playback starts from the selected section.
Notes:
Input invalid ” will display. You should re-enter correct
• If the time entered is not permitted by the DVD, “
time.
• Some discs may not respond to this process.
• Some scenes may not be located as precisely as you specified.
• This method for accessing specific locations is available only within the current title of the DVD.
Locating a specific title
If a DVD contains title numbers, you can locate a specific title by directly selecting its title number.
1. Press the GOTO button.
1
Tt:01ch:05
6
Tt:
ch:
2
Tt:
ch:
7
Tt:
ch:
3
Tt:
ch:
8
Tt:
ch:
4
Tt:
ch:
9
Tt:
ch:
5
Tt:
ch:
10
Tt:
ch:
Clear
Exit
Start
Next
Clear: Delete all input programs.
Exit: Exit memor y menu and return to normal
playback.
Start: Start memory playback.
Next / Prev: Move to the next / previous setup page.
2. Input the title (2 digits) and chapter (2 digits) by
pressing the number buttons (for example: 01
02, 02 05, 02 11). It will move to the next item
automatically.
• You can use the Cursor buttons ( , , , ) to
move the highlighted bar to any item, and reenter the title and chapter. Press the
NEXT /
PREV to move to the next / previous setup
page.
• You can use the Cursor buttons ( , , , ) to
move the highlighted bar to “Clear”, “Exit”, “Start”
or “Next / Prev”, then press the ENTER button to
confirm.
Title 01/03 Chapter 00/00
2. Press the / button to highlight title number, press the corresponding number buttons (2 digits) for the
title you want (for example: 02, 08, 10 or 15. If you press only 1 numeric button, press the ENTER button to
confirm).
3. Playback starts from the selected title.
Notes:
Input invalid ” will display. You should repeat
• If the title number entered is not permitted by the DVD, “
steps 1 and 2 to re-enter correct numbers.
• Some discs may not respond to this process.
• This method of locating a title is available only on a DVD that contains title numbers.
3. Press the
PLAY button to star t memor y
playback (“ Program ” appears on the screen).
4. To resume normal playback from memor y
playback
1). Press the MEMORY button to display the
memory menu.
2). Use the Cursor buttons ( , , , ) to move
the highlighted bar to “Stop”. Press the ENTER
button to confirm “Stop”.
3). Press the MEMORY button to resume normal
playback from memory playback (“ Program ”
disappears from the screen).
Notes:
• If the title or chapter number entered is not
permitted by the DVD, it will disappear. You
should re-enter the correct numbers.
• You should input items one by one following the
1, 2, 3 ... sequence.
• If the DVD contains only one title, you can only
arrange order for chapters.
• Some discs may not permit memory playback
operation.
• If you select repeat during memory playback,
the DVD player repeats the current memory
playback.
• If you press the MEMORY button while the
display appears on the TV screen, the display
disappears.
• The programmed selections will be cleared when
you press the STOP button two times, open
the disc tray or turn off the DVD player.
Sound system
Customizing the function settings
Dolby Digital
System setup
Language setup
Video
Language
System
- - Language Setup Page - OSD Language
Audio
Subtitle
Disc Menu
Eng
Eng
Off
Eng
Go To Language Setup Page
Notes:
• Some DVDs may not play in the audio language you selected. A prior language may be programmed on
the disc.
• Some DVDs may be set to display subtitles in a language other than the one you selected. A prior subtitle
language may be programmed on the disc.
• Some DVDs allow you to change subtitle selections using the disc menu only. If this is the case, press the
MENU button and choose the appropriate subtitle language from the selection on the disc menu.
• Some DVDs may not include your pre-selected language. In this case, the DVD player automatically displays
disc menus consistent with the disc's initial language setting.
Video setup
Video
Language
- - Video Setup Page - Brightness
Contrast
00
00
Go To Video Setup Page
System
Repeating a title
You can play a single track or the whole disc repeatedly.
Repeating a single track
1. While the CD is playing, press the REPEAT DISC
button until the “ Repeat One ” indicator displays on
the screen. The current track is played repeatedly.
Repeating a specific section
You can play a specific section repeatedly.
1. While the disc is playing, press the REPEAT A-B
button at the beginning of the section (“
A ”
is displayed) you want to play repeatedly.
2. Press the REPEAT A-B button again at the end of
AB ” is displayed).
the section (“
3. The unit will immediately begin replaying your
selection.
To resume normal playback
4. While the disc is playing, press the REPEAT A-B
button until the “
AB OFF ” indicator displays
on the screen.
Notes:
• Some discs may not permit A-B repeat operation.
• You cannot set the A-B repeat function for a
segment that includes multiple camera angles.
• You can specify a segment only within the
current title or track.
• There may be a slight difference between point
A and the location where playback actually
resumes depending on the disc.
Repeating the whole disc
2. While the CD is playing, press the REPEAT DISC
button until the “ Repeat All ” indicator displays on
the screen. The whole disc is played repeatedly.
To resume normal playback
3. While the CD is playing, press the REPEAT DISC
button until the “ Repeat Off ” indicator displays
on the screen.
Locating a specific chapter
1. Press the SETUP button in stop mode.
2. Press the / button to select Video Setup Page.
3. Press the / button to select the option (Brightness or
Contrast), then press the button.
4. Press the / button to adjust the setting, then press the
ENTER button to confirm.
5. Repeat steps 3 and 4 to adjust other options. Press the
button to return to the previous menu.
6. Press the SETUP or RETURN button to exit the menu.
3 /3
Note: This function can only be used for discs on which scenes shot from multiple angles have been recorded.
Locating a desired section
1. Press the SETUP button in stop mode.
2. Press the button to select Language Setup Page.
3. Press the / button to select the option (OSD Language,
Audio, Subtitle or Disc Menu), then press the button.
4. Press the / button to select your preferred language,
then press the ENTER button to confirm.
5. Repeat steps 3 and 4 to adjust other options. Press the
button to return to the previous menu.
6. Press the SETUP or RETURN button to exit the menu.
Sequence of angle shots (Example)
2 /3
Repeating a chapter
1. While the DVD is playing, press the REPEAT DISC
Chapter ” indicator displays
button until the “
on the screen. The current chapter is played
repeatedly.
1/3
1
1 /3
You can play a specific title or chapter repeatedly.
(Title repeat, chapter repeat, A-B repeat)
1. Press the SETUP button in stop mode.
2. Press the / button to select System Page.
3. Press the / button to select the option (TV Display or
Default), then press the button.
4. Press the / button to adjust the settings, then press the
ENTER button to confirm.
5. Repeat steps 3 and 4 to adjust other options. Press the
button to return to the previous menu.
6. Press the SETUP or RETURN button to exit the menu.
Video
Language
Tv Display
Default
Wide
No
Dolby Digital is a technology developed by Dolby Laboratories. Soundtracks encoded in Dolby Digital can
reproduce from one to 5.1 discrete channels of excellent quality audio.
The unit automatically recognizes the Dolby Digital bitstream and provides a downmix suitable for twochannel listening. An additional Dolby Digital decoder is required for reproduction of the discrete multi-channel
soundtracks available on many DVDs.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Go To System Page
TV Display
Pan Scan
• When wide-screen video is played, this mode clips the right and left sides of the
image so that it can be viewed on a conventional screen.
• Some wide-screen DVDs that do not permit Pan Scan mode playback are
automatically played in letterbox mode (black bands that appear at the top and
bottom of the screen).
Letter Box
• When wide-screen video is played in this mode on a conventional screen, black
bands appear at the top and bottom of the screen.
Wide Screen
• This is the correct mode for playing wide-screen videos on the unit screen or
other external wide-screens.
Notes:
• The displayable picture size is preset on the DVD. Therefore the playback picture
of some DVDs may not conform to the picture size selected.
• When you play DVDs recorded in the 4:3 aspect ratio, the playback picture will
always appear in the 4:3 aspect ratio regardless of the TV display setting.
• Select Wide Screen to conform the LCD screen on the unit. Always be sure that
your TV display conforms to the actual TV in use if you connect the unit to a TV.
Default
It takes 3-5 seconds to reset the DVD settings to the factory default.
System
- - System Page - -
Maintenance
Cleaning the disc
Pan Scan
Letter Box
A defective or soiled disc inserted into the unit can cause sound to drop out during playback.
Handle the disc by holding its inner and outer edges.
• Do NOT touch the surface of the unlabeled side of the disc.
• Do NOT stick paper or tape on the surface.
• Do NOT expose the disc to direct sunlight or excessive heat.
• Clean the disc before playback. Wipe the disc from the center outward with a cleaning cloth.
• NEVER use solvents such as benzine or alcohol to clean the disc.
• Do NOT use irregular shaped discs (example: heart shaped, octagonal, etc.). They may cause malfunctions.
Viewing JPEG files
This unit can play JPEG files recorded on a CD-R or CD-ROM disc (CD-RW is not recommended).
Viewing JPEG files
1. Slide the OPEN knob rightwards to open the disc door.
2. Hold a JPEG file disc by its edges and gently push it onto the
spindle with the label side facing up until you hear a “click”.
3. Close the disc door. The JPEG files on the disc will display
automatically or a folder list appears.
4. Press the STOP button to display a folder list. Press the /
button to highlight a JPEG file to play. Press the
PLAY
button to start playback.
•
Wide Screen
Troubleshooting guide
Symptom
Cause (and remedy)
No power.
• Ensure the AC power adapter is connected.
• The unit is not turned on.
The remote
control does
not function.
•
•
•
•
No sound or
only a very
low-level
sound is
heard.
• The volume control is located on the side of the unit – please try adjusting this.
• The system is in pause mode. Press the
PLAY button to return to normal play mode.
• The unit is in fast-forward or fast-reverse mode. Press the
PLAY button to return to
normal play mode.
• Make sure the AUDIO/VIDEO output connections are correct.
• The DTS DVD cannot be decoded to have speaker output.
• The unit is too hot; shut off the unit for 30 minutes to cool it down.
No picture.
• The region number of the disc doesn't match the region
number of this unit.
The picture is
not clear.
• Clean the disc.
• The disc is scratched.
• Adjust the LCD's brightness and contrast using the VIDEO MODE button on the remote control.
The disc does
not play.
Be sure to turn the unit off and disconnect the AC power adapter before cleaning the unit.
Wipe the unit with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth that has
been dipped in a weak soap-and-water solution and wrung out thoroughly, then wipe with a dry cloth.
Never use alcohol, benzine, thinner, cleaning fluid or other chemicals. Do NOT use compressed air to
remove dust.
Before transporting the unit, remove the disc from the disc compartment.
Make sure the infrared remote sensor is not blocked.
Make sure the plastic sheet has been removed from the remote control.
Point the remote directly at the infrared remote sensor on the unit.
Replace the battery in the remote control with a new one.
Severe hum or • The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol.
noise is heard. • Clean the disc.
•
•
•
•
•
There is no disc inside (“No Disc” appears on the screen).
Insert the disc correctly with the playback side facing down.
Clean the disc.
A non-NTSC disc has been inserted. The unit and disc region number are incompatible.
Condensation may have formed inside the unit due to a sudden change in temperature.
Wait about an hour for it to clear and try again.
Need More Help?
Please visit online help at http://www.RCAav.com
Important note
•
\
DSCN0281
DSCN0282
DSCN0283
DSCN0284
DSCN0285
DSCN0286
Notes:
PLAY button to resume picture slide show.
• You can press the PAUSE button to freeze the picture. Press the
• You can press the
PREV or
NEXT button to change the picture.
• You can press the ANGLE button to rotate direction of the picture by 90°.
• Some discs may not permit this operation.
Cleaning the unit
•
•
00:00 00:00
001/035
Printed in China
811-837291W050
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement