Art Decor HAA6515-S Instructions / Assembly

Below you will find brief information for curtain rod. This document provides detailed instructions on installing and using your new curtain rod. The instructions cover different styles, including installation on a window and cutting down the rod to fit your needs. Additionally, it helps you with the installation of the support brackets and fixing final pieces. The document also includes some helpful tips for cutting down the rod for a perfect fit.

PDF Download

Document

1) Decide desired height of supports over window. Install the L—brackets no more than 3” from the ends of the rod.

Make sure the supports are level.

2) Place cradle bracket over L-bracket and secure with screw ‘A’, SCREW ‘A’ CRADLE

BRACKET

3) For 10 foot rods, screw both rods together with included joiner screw,

4) Place rings onto the rod at this time if needed,

5) Place rod into Cradle bracket and tighten with screw ‘B’.

L–BRACKET

Style A) Place ﬁ nial over end of rod and tighten with set screw. (see photo 1)

Style B) For Resin ﬁ nial - screw ﬁ nial into plastic plug already inserted into end of rod. (see photo 2)

SCREW ‘B’

PHOTO 1 PHOTO 2

Cutting down a rod if necessary:

1) Measure rod and determine your cut.

2) Cover area with masking tape 1” on either side of determined cut to avoid scratching the surface of rod.

3) Cut rod with hack saw or pipe cutter then push out plastic plug and reinsert into new end. (only appies to for resin ﬁ nials)

1) Decide desired height of supports over window. Install the L—brackets no more than 3” from the ends of the rod.

Make sure the supports are level.

2) Place cradle bracket over L-bracket and secure with screw ‘A’, SCREW ‘A’ CRADLE

BRACKET

3) For 10 foot rods, screw both rods together with included joiner screw,

4) Place rings onto the rod at this time if needed,

5) Place rod into Cradle bracket and tighten with screw ‘B’.

L–BRACKET

Style A) Place ﬁ nial over end of rod and tighten with set screw. (see photo 1)

Style B) For Resin ﬁ nial - screw ﬁ nial into plastic plug already inserted into end of rod. (see photo 2)

SCREW ‘B’

PHOTO 1 PHOTO 2

Cutting down a rod if necessary:

1) Measure rod and determine your cut.

2) Cover area with masking tape 1” on either side of determined cut to avoid scratching the surface of rod.

3) Cut rod with hack saw or pipe cutter then push out plastic plug and reinsert into new end. (only appies to for resin ﬁ nials)

Hello! I am an AI chatbot specifically trained to assist you with the Art Decor HAA6515-S Instructions / Assembly. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key features

Installation on window
Cutting down the rod
Support brackets
Final pieces
Different styles

Frequently asked questions

The supports should be installed at a height that is appropriate for your needs and preferences.

Install the L-brackets no more than 3 inches from the ends of the rod.

Measure the rod and determine the desired cut length, cover the area with masking tape, then cut the rod using a hack saw or pipe cutter.

For a 10 foot rod, you will need to screw both rods together using the included joiner screw.

Style A involves placing a finial over the end of the rod and tightening it with a set screw. Style B involves screwing the finial into a plastic plug that is already inserted into the end of the rod.