TH 110 - JSP, s.r.o.
Humidity and temperature
transmitter
TH 110
KEY POINTS
- Measuring range from 5 to 95%RH and from 0 to 50 °C (ambient model) or from -20 to +80 °C
(duct or remote model)
- 0-10 V output, active, power supply 24 Vac/Vdc (3-4 wires) or 4-20 mA output, passive loop,
power supply from 16 to 30 Vdc (2 wires)
- ABS V0 housing IP65 (duct or remote model) or IP20 (ambient model), with or without display
- Alternating display of humidity and temperature
- “¼ turn” system mounting with wall-mount plate
- Housing with simplified mounting system
FEATURES OF HOUSING
Duct model
112 mm
Material
ABS V0 as per UL94
90 mm
Protection
IP65 (duct and remote models)
IP20 (ambient model)
109 mm
46 mm
Display
LCD 10 digits. Size : 50 x 17 mm
Alternating display of humidity and
temperature
Ø 13 mm
90 mm
46 mm
150 mm
90 mm
Height of digits
Values : 10 mm
Units : 5 mm
Cable gland (remote and duct models)
For cables Ø 8 mm maximum
109 mm
80 mm
41 mm
Ambient model
Remote model
Weight
124 g (ambient model) ; 135 g (duct and
remote models)
Cable of remote probes : length 2 m and Ø
4.8 mm in silicone
PART NUMBER
To order, just add the codes to complete the part number :
TH110
Probe
Power supply / Output
A : Active – 24 Vac/Vdc – 0-10 V
P : Passive – 16/30 Vdc – 4-20 mA
Display
O : with display
N : without display
S : Ambient
A : Duct
D : Remote
Example : TH110 – ANS
Humidity and temperature transmitter TH110, 0-10 V
active, without display, ambient model
TECHNICAL FEATURES IN TEMPERATURE
TECHNICAL SPECIFICATIONS
Measuring range
Ambient model : from 0 to 50 °C
Remote and duct models : from -20 to +80 °C
Accuracy*
CMOS : ±0.4 % of reading ±0.3 °C
NTC : ±0.3°C (de -40°C à 70°C) ; ±0.5°C outside
Unit of measurement
°C / °F
Response time
1/e (63%) 15 s
Sensitive element
Ambient model : CMOS
Remote and duct models : NTC
Resolution
0.1 °C
Type of fluid
Air and neutral gases
Output / Power supply
- active sensor 0-10 V (power supply 24
Vac/Vdc ± 10%), 3-4 wires
- passive loop sensor 4-20 mA (power
supply 16/30 Vdc), 2 wires
- maximum load : 500 Ohms (4-20 mA)
- minimum load : 1 K Ohms (0-10 V)
Consumption
2 VA (0-10 V) or max. 22 mA (4-20 mA)
**
All the accuracies indicated in this technical datasheet were stated in laboratory conditions, and can be guaranteed for measurements carried out in the same
conditions, or carried out with calibration compensation.
Electromagnetical compatibility
EN61326
Electrical connection
Screw terminal block for cables Ø0.05 to
2.5 mm2
TECHNICAL FEATURES IN HUMIDITY
Measuring range
From 5 to 95% RH
Accuracy**
±1.5% RH (if 15°C ≤ T ≤ 25°C) on remote and duct models
±1.8% RH (if 15°C ≤ T ≤ 25°C) on ambient model
Drift linked to temperature
±0.04 x (T-20) %RH (if 15°C ≤ T ≤ 25°C)
Unit of measurement
% RH
Response time
1/e (63%) 4 s
Type of sensor
Ambient model : CMOS
Remote and duct models : NTC
Resolution
0.1% RH
Factory adjustment uncertainty
±0.88% HR
Type of fluid
Air and neutral gases
PC communication
Kimo USB-mini Din cable
Environment
Air and neutral gases
Operating temperature of the housing
From 0 to 50 °C
Operating temperature of the probe
From -20 to +80 °C
Storage temperature
From -10 to +70 °C
**
All the accuracies indicated in this technical datasheet were stated in laboratory conditions, and can be guaranteed for measurements carried out in the same
conditions, or carried out with calibration compensation.
As per NFX 15-113 and the Charter 2000/2001 HYGROMETERS, GAL (Guaranteed Accuracy Limit) which has been calculated with a coverage factor value of 2
is ±2.58%RH between 18 and 28°C on the measuring range from 3 to 98%RH. Sensor drift is less than 1%RH/year.
CONNECTIONS
Fixed back housing
Inside the front housing
Removable front face
Inactive
switch
Active switch
LCC-S
connection
Output
terminal block
Power supply
terminal block
Cable gland
ELECTRICAL CONNECTIONS – as per NFC15-100 standard
This connection must be made by a qualified technician. To make the connection, the transmitter must not be energized.
For TH110-AOS, TH110-ANS, TH110-AOD, TH110-AND, TH110-AOA, TH110-ANA models with 0-10 V output – active :
To make a 3-wire connection, before powering up the transmitter, please connect
the output ground to the input ground. See drawing below.
VT GND VRH
6
7
-
+
3
7
Power supply
- 24 Vdc
V
V
or
V
-
+
0-10 V output
+
Power supply
24 Vdc
Display/regulator/PLC passive type
N L
6 7
or
1
Display/regulator/PLC
passive type
0-10 V output
6
+
4 5
3 wires
+
+
V
2
+
-
1
+
4
wires
VT GND VRH
+
2
+
5
+
1
4
+
3
2
6
N +
4 5
+
3
L
7
L
N
Power supply
24 Vac
class II
L
3 wires
Power supply
24 Vac
N class II
0-10 V output
V
-
+
+
4 wires
V
Display/regulator/PLC passive type
3 wires
For TH110-POS, TH110-PNS, TH110-POD, TH110-PND, TH110-POA, TH110-PNA models with 4-20 mA output – passive :
1
2
IT Vdc IRH Vdc
- + - +
4 5 6 7
3
1
Power supply
16-30 Vdc
Display/regulator/PLC
passive type
4-20 mA output
+-
2
wires
3
2
wires
+
2
wires
or
A
+
-
+
2 wires
2
IT Vdc IRH Vdc
- +
- +
4 5 6 7
A
-
Power supply
16-30 Vdc
2
wires
+ -
+
A
A
16-30 Vdc
16-30 Vdc
Display/regulator/PLC
active type
4-20 mA output
4-20 mA output
Display/regulator/PLC
passive type
SETTINGS AND USE OF THE TRANSMITTER
➢
Configuration
It is possible to set the measuring ranges and the unit of the instrument either by switch and/or via software.
To configure the transmitter, it must not be energized. Then, you can make the settings required, with the DIP switches (as shown on the
drawing below). When the transmitter is configured, you can power it up.
➢
Configuration by switch
To configure the transmitter, unscrew the 4 screws from the housing then
open it. DIP switches allowing the different settings are then accessible
On-off switch
1
2
3
4
Output setting
Unit setting
Switch actif
Please follow carefully the combinations beside with the DIP switch. If the combination is wrongly done, the following message will appear
on the display of the transmitter “CONF ERROR”. In that case, you will have to unplug the transmitter, place the DIP switches correctly, and
then power the transmitter up.
➢
Units setting – active switch
To set a unit of measurement, put the on-off switch 4 of the units as shown below.
Configurations
Combinations
°F
1
1
2
2
3
3
4
4
Outputs setting – active switch
To set an output, put the on-off switches 1, 2 et 3 of the measuring ranges as shown below.
Configurations
Combinations
From 0 to +50°C
From -20 to +80°C
From -50 to +50°C
From 0 to 100°C
1
1
1
1
2
2
2
2
3
3
3
3
4
4
4
4
CONFIGURATION VIA LCC-S SOFTWARE (option)
An easy and friendly configuration with the software !
It is possible to configure intermediate ranges, an offset
Example : for a 0-100 °C transmitter, minimum delta minimum is 20 °C. The instrument can be configured from 0 to +20 °C or from -10 to
+10 °C.
In order to compensate a possible drift of the sensor, it is possible to add an offset to the displayed value by the TH110 transmitter : it
shows 48%RH, a standard instrument shows 45%RH. It is then possible, via the software, to integrate an offset of -3 to the displayed
value by the TH110 instrument.
• To access the configuration via software :
- Set the DIP switches as shown beside.
- Connect the cable of the LCC-S to the connection of the transmitter.
• Please refer to the user manual of the LCC 100 to make the configuration.
1
2
3
4
Active switch (S1)
The configuration of the parameters can be done either with the DIP switch or via software (you can not combine both solutions).
75 mm
MOUNTING
37.5 mm
8 mm
4.5 mm
14 mm
A
7.5 mm
MAINTENANCE
Please avoid any aggressive solvent. Please protect the transmitter and its probes from any cleaning product containing formalin, that may be used for cleaning
rooms or ducts.
OPTIONS AND ACCESSORIES
●
●
KIAL-100A : Power supply class 2, 230 Vac input, 24
Vac output
LCC-S : configuration software with USB cable
●
●
●
Stainless steel sliding fittings
PC cable gland
ABS connection with
connection gland
●
●
Stainless steel connections
Wall-mount plate for humidity
remote probe
Your supplier:
JSP, s.r.o., Raisova 547, 506 01 Jičín, Czech Republic
Phone: +420 493 760 811, Fax: +420 493 760 820, e-mail: [email protected]
JSP Industrial Controls
www.jsp.cz
68 mm
A
50 mm
Ambient model does not have any mounting plate.
4 fixing holes are present inside the back housing. Use them to install
the transmitter on the required location.
40 mm
23.75 mm
To mount the transmitter, mount the ABS plate on the wall (drilling : Ø6 mm, screws and pins are
supplied).
Insert the transmitter on the fixing plate (see A on the drawing beside). Rotate the housing in clockwise
direction until you hear a “click” which confirms that the transmitter is correctly installed.
FTang – transmitter_TH110 – 08/03/13 – RCS (24) Périgueux 349 282 095 Non-contractual document – We reserve the right to modify the characteristics of our products without prior notice.
➢
°C
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement