FINN TITAN 280, 330, 400 HydroSeeder Parts and Operator’s Manual

The FINN TITAN 280, TITAN 330, and TITAN 400 HydroSeeders® are designed to mix and apply water, seed, fertilizer, agricultural lime, and hydraulic mulch to the prepared seedbed. The slurry tank holds the materials. The mixing process is done by a dual-agitation process and the slurry is pumped to the discharge assembly and directed onto the seedbed by the operator. The equipment is designed for maximum efficiency.

PDF Download

Document

9281 LeSaint Drive • Fairfield, Ohio 45014

Phone (513) 874-2818 • Fax (513) 874-2914

Activate

Your Warranty

By Registering

TODAY!!!

TITAN280/TITAN330/TITAN400

HydroSeeder

®

Parts and Operator’s Manual

Mode.

MMA Serial No. _____________

LBTITAN280-TITAN330-TITAN400-MO

NOTES

ACTIVATE YOUR FINN EQUIPMENT WARRANTY

IMPORTANT INFORMATION ON ACTIVATING

YOUR FINN EQUIPMENT WARRANTY!!!

IT IS IMPERATIVE THAT YOU, THE PURCHASER, COMPLETE THE FOLLOWING STEP IN ORDER TO

ACTIVATE THE FINN CORPORATION LIMITED WARRANTY.



COMPLETE THE

EQUIPMENT REGISTRATION

FORM

AND MAIL TO THE FINN CORPORATION.

IF FINN CORPORATION DOES NOT HAVE YOUR COMPLETED REGISTRATION

FORM ON FILE, YOUR WARRANTY CLAIM WILL BE DENIED.

Once your FINN equipment has been registered, your FINN Limited Warranty will be activated per the warranty statement on the next page.

<<What should you do if you need repairs or parts under Warranty?>>



NOTIFY FINN CORPORATION OF THE FAILURE OF MATERIAL OR WORKMANSHIP

1-800-543-7166 Extension (246)

[email protected]



AFTER YOU OR YOUR SERVICE DEALER NOTIFY FINN, FINN WILL:



WARRANTY (PENDING FINN’S INSPECTION OF DEFECTIVE PARTS)







SEND YOU REPLACEMENT PART(S) AND A WARRANTY INFORMATION PACKET

REQUEST YOU FOLLOW ALL INSTRUCTIONS AS NOTED IN THE PACKET

▪ Completely fill out the Parts Tag.

▪ Attach the Parts Tag to the defective part(s).

▪ Return the part(s) and the completed Warranty Claim Form to FINN

Corporation using the return shipping label. (Within 2 weeks)

▪ Tape the Orange identifier sheet, marked with the W/RMA number, on the outside of the box in which you are shipping the defective part(s).

LBTITAN280-TITAN330-TITAN400-MO

Warranty period:

Hydroseeders & Straw Blowers 2 years or 2000 hrs which ever comes 1 st

All other equipment 1 year or 1200 hrs which ever comes 1st

OUR WARRANTY TO YOU:

Finn Corporation warrants to you, the original purchaser, for use (or rental to others for use) all new construction machinery, parts and attachments (except

Commercial Limited Warranty

Effective 4/1/2011

4. The warranty shall be null and void to the extent any defect or failure of the products warranted arises out of or is caused by accessories or those referred to herein) that are manufactured by Finn to be free from component parts not manufactured or supplied by Finn Corporation, defects in material and workmanship for a period noted above. whether same are supplied by purchaser, dealers, or any other party.

Replacement parts provided under the terms of this warranty are warranted

5. This Warranty does NOT cover any costs associated with transporting for the remainder of the warranty period applicable to the product to which the equipment for warranty service, such as mileage, fuel, or man hours; such is the responsibility of the equipment owner. parts are installed, as if parts were original components of the product.

WHAT FINN WILL DO:

6. Dealers & Customers are responsible to follow all guidelines related to Seasonal & Long Term Storage of Equipment, as advised in operation

Upon notification of Finn concerning a failure of material or workmanship in

& equipment manuals. i.e. Finn, Engine, Clutch, Pump, Motor, etc. accordance with the above stated Warranty, Finn Corporation will: x

Verify claim falls within the valid warranty time frame. x

Verify the product and equipment has been registered with Finn in order to be eligible for warranty coverage. x

Upon affirmation of warranty period and registration, Finn will send to

Equipment failures caused by neglect of these guidelines are not warrantable.

THIS IS THE ONLY EXPRESS WARRANTY ON OUR

PRODUCTS: you a new or repaired replacement part(s), whichever Finn elects and a

“Warranty Claim Information packet” containing instructions for

We neither assume nor authorize anyone to assume for us any other express warranty. The Distributor/Dealer has no authority to make any representation or promise on behalf of Finn Corporation or to modify the processing the warranty claim. x

Evaluate the part when defective part is returned. Note: Failure to terms or limitations of this warranty in any way. return defective part within two weeks will result in an invoice being

THIS WARRANTY THEREFORE SHALL BE IN LIEU OF ALL sent to the customer. In addition, if damage to a part is determined not

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT

NOT LIMITED TO, ANY IMPLIED WARRANTY OF to be covered under the warranty, the customer will be billed. x

Reconcile costs with customer for parts and shipping, as determined by our inspection of failed parts, and confirmation of warranty coverage, per the terms of this warranty. x

Correction of nonconformities, in the manner provided above, shall

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

LIMITATIONS ON OUR RESPONSIBILITY WITH

RESPECT TO PRODUCTS PURCHASED:

THE REMEDIES OF THE USER SET FORTH HEREIN ARE constitute fulfillment of all liabilities of Finn Corporation.

WHAT YOU MUST DO TO OBTAIN WARRANTY SERVICE:

As the purchaser covered under the above limited warranty you must

EXCLUSIVE, WITHOUT REGARD TO WHETHER ANY DEFECT

WAS DISCOVERABLE OR LATENT AT THE TIME OF DELIVERY

OF THE PRODUCT TO THE PURCHASER.

REGISTER the equipment with Finn FAILURE TO REGISTER

ALL WARRANTY REPAIR MUST BE DONE BY A FINN

WILL VOID THE WARRANTY. x

Claim Number: Notify the warranty Dept. same day or next day of any intent to do warranty work and obtain a “Warranty Claim Number,” x

All warranty labor must be pre-approved by providing Finn with an

AUTHORIZED SERVICE PROVIDER OR AUTHORIZED REPAIR

SHOP OF FINN’S CHOICE.

TRANSPORTATION, HAULING, STORAGE, OR OTHER SIMILAR

COSTS ARE NOT PART OF FINN’S OBLIGATION UNDER THE

LIMITED WARRANTIES AND IS THE RESPONSIBILITY OF THE estimate of labor costs. Once approved, Finn will issue you a Work

Authorization Number, prior to work being performed.(EXCEPTION:

EQUIPMENT OWNER.

THE ESSENTIAL PURPOSE of this exclusive remedy shall be to

Unless the labor is per the Labor Allowance Schedule or less) x

The labor costs reimbursement will be based on the Labor Allowance provide the original purchaser with repair or replacement of parts that prove to be defective within the period and under the conditions

Schedule established by Finn and where not applicable, on a reasonable previously set forth. This exclusive remedy shall not have failed of its number of hours as determined by Finn. x

Notify Finn Corporation of any failure of material or workmanship as essential purpose (as that term is used in the Uniform Commercial Code) provided Finn remains willing to repair or replace defective parts within described under this warranty.

¾ Web notification: [email protected]

¾ Phone 1-800-543-7166 extension 246 x

Complete the required steps in the “Warranty Claim Information packet” (which Finn will send you) and return the defective part(s) as a commercially reasonable time after it obtains actual knowledge of the existence of a particular defect.

IN NO EVENT shall Finn be liable for any special, consequential, directed in the packet to Finn Corporation. x

Should the failed part, be a hydraulic component, Finn may send you an

“Oil Analysis Kit,” requesting that a sample of oil from the hydraulic incidental or indirect damages, including lost profits or lost commercial opportunities, with respect to the sale of the above warranted product or anything done in connection therewith, or for system be taken, and mail it to a lab. Follow the instruction sheet, on property damage sustained by a person claiming to be a third party how to use your Finn Oil Analysis Kit that comes with the Kit. Failure beneficiary of a surviving warranty under the law of any jurisdiction. to comply when requested will void the warranty.

WHAT THE WARRANTY DOES NOT COVER:

1. Normal wear parts and Allied Equipment or trade accessories not

NOTICE:

FINN CORPORATION URGES the use of only Finn corporation manufactured by it, such as but not limited to items such as various supplied parts and attachments to assure proper performance and safe filters, fluids, brakes, clutch linings, belts, hoses, light bulbs, operation of Finn corporation equipment. Insist on parts and mechanical seal, over center clutches, tires, ignitions, starters, batteries, attachments manufactured or supplied by Finn corporation when magnetos, carburetors, engines and labor, or like or unlike equipment or you purchase, repair or replace your Finn equipment and accessories. (Such being subject to the warranty, if any, provided by attachments. Because Finn corporation cannot assure that parts and their respective manufacture). attachments not manufactured or supplied by Finn meet Finn

2. Secondhand, used, altered, or rebuilt machines or parts. corporation's quality standards, specifications, or operating

3. Defects, malfunctions or failures resulting from accidents, abuse, requirements, our warranty is not effective to the extent any failure of or misuse, improper servicing, or neglect of required operational defect in a Finn corporation product arises from or is caused by parts, guidelines and maintenance service, as outlined in the Finn

Corporation’s Operators Manual(s). attachments or components not originating with Finn corporation. Use of

Finn corporation equipment with parts and attachments not manufactured or supplied by Finn could result in personal injury.

INDEX

SAFETY FIRST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

SAFETY SUMMARY SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5

OPERATION and MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–41

Definition of Hydroseeding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

The FINN HydroSeeder® and How It Works . . . . . . . . . . . . . . . . . . . . . . . . . 6

Mounting The HydroSeeder® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Dimensions, Capacities, and Truck Requirements . . . . . . . . . . . . . . . . . . 6–7

Truck Mounting Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

General Mounting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–9

Pre-Start Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Equipment Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Two-Valve Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10–11

1. Discharge Through Boom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

2. Extension Hose Through Boom . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

3. Extension Hose or Hose Reel Through Remote Port . . . . . . . . . . .11

Starting Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

PowerView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–14

Faceplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

PowerView Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13–14

PowerView Menus (First Time Start-Up). . . . . . . . . . . . . . . . . . . . . . 13

Stored Fault Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Area Coverage - Material Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–16

Tank Capacity Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17–18

Loading (For Wood Fiber Mulch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Loading and Mixing BFM, FGM, SMM, and

Other Highly Viscous Slurries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21–22

Prior to Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Discharge Nozzle Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Application of Slurry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

I. General Application Techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

II. Discharge Through the Boom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

III. Procedures When Using Hoses . . . . . . . . . . . . . . . . . . . . . . . . . 24–26

A. Pump Take-Off System or Hose Reel With Remote Valve . . . . 25

B. Extension Hose System Without Remote Valve . . . . . . . . . . . . 25

C. Hose Work With Radio Remote Transmitter . . . . . . . . . . . . . . . 26

Reloading Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Liming With The HydroSeeder® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Hydroseeder

is a registered trademark of the FINN Corporation

Continued . . .

INDEX

CLEANING AND MAINTENACE

Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32–37

After First 4 to 8 Hours of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Daily. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Weekly or Every 40 Hours of Operation . . . . . . . . . . . . . . . . . . . . . . 32–33

Seasonal and Winter Storage Maintenance . . . . . . . . . . . . . . . . . . . . . . 33

Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Clump Maintenance Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34–37

Lubrication and Fluids Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38–39

PARTS SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42–83

Pictorial Reference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Structure and Railing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44–45

Hatch View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46–47

Discharge Boom Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48–49

Engine and Radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50–51

Radiator Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52–53

Clump, Piping, and Discharge Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 54–55

Pump Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56–57

2ND Discharge Boom Assembly - Optional . . . . . . . . . . . . . . . . . . . . . . . 58–59

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60–61

Control Box Wiring (Internal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62–63

Control Box Wiring (External) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Relay Box Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65–67

Ground Level Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Engine Wiring Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Agitator and Seal Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70–71

Hydraulic Agitator Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72–73

Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74–75

Hydraulic System, Third Agitator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76–77

Hose Reel Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78–79

Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80–81

Tool Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Spare Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

SAFETY FIRST

With any piece of equipment, new or used, the most important part of its operation is

SAFETY!

FINN Corporation encourages you and your employees to familiarize yourselves with your new equipment and stresses safe operation.

The first five pages of this manual are a summary of the main safety aspects associated with this unit. Be sure to read and understand completely before operating the machine.

The symbols below are used throughout the operation and maintenance sections of this manual to call attention to safety procedures.

DANGER

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE

Indicates practices that are not related to personal injury.

NOTE:

Gives helpful information.

CALIFORNIA

Proposition 65 Warning

The engine exhaust and some of its constituents are known to the

State of California to cause cancer, birth defects, and other reproductive harm.

CALIFORNIA

Proposition 65 Warning

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

HYDROSEEDER

®

SAFETY SUMMARY SECTION

It is important that all operators of this machine are familiar with all safety aspects covered in this section and have read the entire Operator’s Manual before operating the machine. Always keep a copy of this manual with the machine. It is the responsibility of the operator of the machine to fully understand this safety summary section. Remember that YOU are the key to safety. Good safety practices protect not only you but also the people working with and around you. Keep in mind that this safety section is written for this type of machine only.

Practice all other usual and customary safe working precautions. Above all, remember that safety is up to you.

The FINN HydroSeeder® is designed to mix and apply water, seed, fertilizer, agricultural lime, and hydraulic mulch to the prepared seedbed. The resultant slurry from mixing one or more of the above materials may react, causing harmful or deadly gasses within the tank. Heat, evaporation, or extended emptying period can/will accelerate the formation of these gasses. Please contact your supplier(s) of these slurry components regarding their potential reactivity.

I. PRE-START EQUIPMENT CHECK (equipment check is to be made with the engine off):

1. If you have a chassis-mounted unit, check devices securing HydroSeeder® to the truck or trailer frame.

2. I f

HydroSeeder® is a trailer unit, check hitch and hitch bolts, lights, brakes, and all safety components.

3. Make sure loading hatch bag cutter is in place and secure.

4. Check that all guard railing is in place and secure.

5. Verify that all guards are in place.

6. With the ignition switch ON, verify that the signal horn is operating correctly.

7. By carefully looking down through the loading hatch, inspect the slurry tank for foreign objects. Never enter the tank without following the procedures described in step 3 of IV. MAINTENANCE on page 4.

8. Remove unnecessary objects (or material) from the tank top.

9. Make sure no one is working on or inside the machine.

Give a visual and audible signal that all is clear before starting the engine.

10. Inspect all hydraulic hoses for cracks, bulges, or damage. If hoses are bad, replace immediately.

11. Inspect all discharge hoses for cracks, bulges, or damage. If hoses are bad, replace immediately.

II. MACHINE OPERATION:

1. Always wear safety goggles when operating the machine.

Other safety attire such as safety shoes, ear protection, gloves, hard hats, dust masks, etc. should be worn as required by warning decals on machine, operator’s manuals, or job site requirements. Remove rings, watches, etc. Avoid wearing loose-fitting clothing that may get caught in rotating machinery.

2. Do not operate the machine without all guards in place.

3. Do not load unit while in transit. Load only when parked and unit is as level as possible. Take care not to drop pens, lighters, etc. or pieces of paper or plastic bags into the tank as these objects might plug the slurry system.

Should any object be dropped into the tank, do NOT reach into the tank to retrieve the foreign object. See step 3 under IV. MAINTENANCE on page 4 before allowing any personnel to enter the tank.

4. Make sure area to be sprayed is clear of all persons, animals, etc.

5. The driver of the carrying or towing vehicle is responsible for the safety of the operator(s) of the machine.

Make sure the driver is aware of and avoids all possible hazards to the operator(s) of the machine, such as low tree limbs, low power lines, etc. Vehicles on which equipment is mounted or towed must be stopped and started gradually. Avoid abrupt starts or stops.

Never operate on a slope or a hill that may endanger the driver and/or the operator(s). All personnel should review and be familiar with stop/start signals between the driver and operator(s) before going into operation.

Only the operator should be located on the platform during operation.

6. Operator(s) of equipment should never ride on the machine at speeds of greater than 5 mph (8 km/h).

7. Never operate machine in an enclosed area without venting the engine exhaust of both the equipment and vehicle on which the equipment is mounted. Deadly carbon monoxide fumes can accumulate.

8. Never operate this or any other machinery when fatigued, tired, under the influence of alcohol, illegal drugs, or medication. You must be in good physical condition and mentally alert to operate this machine.

9. Never modify the machine. Never remove any part of the machine (except for service and then reinstall before operating).

10. Use proper means (steps, ladder) for mounting and dismounting of the machine.

Never mount or dismount a moving machine.

3. Recirculation valve must be open and material flowing back into the tank when using the remote valve. A closed or plugged recirculation line will cause extreme heat in the pump or discharge lines that will result in severe bodily injury and damage to the equipment.

4. During application through a hose, high pressure can be exerted at the end of the hose. Hose-holding personnel must establish good footing. The operator should apply gradual pressure to the hose only after hose-holding personnel are firmly positioned and have firm control of the hose. Additional personnel to direct hose may be necessary if working on slopes. The proper technique for grasping the hose used by hoseholding personnel is to route and firmly grasp the hose over the shoulder or under both arms. Never route/ hold the hose so it goes between the legs. If the hoseholding personnel finds that it is uncomfortable for him to handle the hose by himself, additional hose holders should be positioned at the end of the hose.

5. Plan application so that the farthest area is covered first, then work back toward the HydroSeeder® so that the individuals are not walking back over slippery ground.

6. Before opening any valves or pipe clamps, shut machine down and check if material in the pipe is hot. If hot, do NOT open valve or pipe clamps, as the hot material may cause severe personal injury. Allow to cool and open with caution.

7. Except when loading materials, keep loading hatch lid closed to protect operator and prevent splashing of wet material onto the tank top.

8. Wash off spillage of slippery mulch or slurry additive from the tank top and platform before operating equipment.

III. SLURRY APPLICATION:

1. Do not aim discharge spray toward power lines, transformers, or other high voltage electrical conductors. Also, do not aim discharge spray toward people, animals, or anything other than the intended application area.

2. Never engage (turn on) clutch when both the recirculation and discharge valves are closed. Operation with both valves closed will result in extreme heat generation that could cause severe bodily injury and damage to the equipment.

IV. MAINTENANCE:

machine, turn off engine and allow all moving parts to stop. To prevent accidental starting, disconnect battery cables. Tag the engine operating area to show that the machine is being serviced.

Use lockout/tagout procedure

(Occupational Safety and

Health Administration [OSHA] 29 CFR 1910.147).

2. Certain hydroseeding amendments, when combined with or without the addition of water or heat or the element of time, may react causing harmful or deadly gasses! Consult your material suppliers regarding reactivity information. The slurry tank must be flushed and drained after each day of operation.

3. Your slurry tank may be considered a confined space by OSHA under 29 CFR 1910.146. Before entering any confined space, your company must develop a procedure for safe entry. Make sure your company’s plan meets all the requirements of 29 CFR 1910.146., or local legal requirement, including the following: a) Drain, flush, and ventilate tank interior.

b) Turn off engine, disconnect battery cables, and perform lockout/tagout procedures (29 CFR 1910.147).

c) Provide continuous ventilation or proper breathing apparatus.

d) If tank must be entered, personnel entering the tank must be tethered to a lifeline.

e) Provide a stand-by individual outside of tank who is able to communicate with person inside and haul him out with the lifeline if necessary.

4. Before loosening any clamps or opening any valves, determine if material in the line is hot by feeling the pipe. Do

NOT allow material to come in contact with personnel. Severe bodily injury could result.

5. On trailer units, perform general maintenance such as checking the safety chains, hitch and hitch bolts, tires, and brakes. Repair or replace if worn or broken. Never operate machine on improperly inflated or damaged tires. Always use a safety cage or cable restraints when re-inflating a repaired tire.

6. Radiator maintenance: Liquid cooling systems build up pressure as the engine gets hot. Before removing radiator cap, stop the engine and let the system cool.

Remove radiator cap only after the coolant is cool.

7. Battery maintenance: Lead-acid batteries contain sulfuric acid, which will damage eyes or skin on contact.

Always wear a face shield to avoid getting acid in the eyes. If acid contacts the eyes, flush immediately with clean water and get medical attention. Wear rubber gloves and protective clothing to keep acid off skin.

Lead-acid batteries produce flammable and explosive gasses. Keep arcs, sparks, flames, and lighted tobacco away.

8. Filling of fuel: Never fill the tank with the engine running, while smoking, or when near an open flame.

Never smoke while handling fuel or working on the fuel system. The fumes in an empty fuel container are explosive. Never cut or weld on fuel lines, tanks or containers. Move at least 10 ft (3 m) away from fueling point before starting engine. Wipe off any spilled fuel and let dry before starting engine.

IMPORTANT: Be careful not to allow fuel, lubricant, hydraulic fluid, or cooling fluids to penetrate into the ground or be discharged into the water system. Collect all fluids and dispose of them in accordance with local municipal regulations.

9. It is recommended that only authorized, genuine FINN replacement parts be used on the machine.

10. Do not use either cold start fluid, if engine is equipped with glow plug type preheater, or other intake manifold type preheater. It could cause an explosion or fire and severe injury or death.

11. Diesel fuel or hydraulic fluid under pressure can penetrate the skin or eyes and cause injury, blindness, or death. Pressure may build up in the hydraulic system; use caution when removing the cap.

12. Make certain that all decals on the machine are maintained in good legible condition. Replacement decals are available through FINN Corporation by specifying part number shown in the lower right-hand corner of the decal. See page 5 for the current safety decals mounted on the unit. See pages 80 and 81 in the

PARTS MANUAL for the location and quantity of all decals on this unit.

CURRENT SET OF SAFETY DECALS

DANGER

CONFINED SPACE HAZARD!

(Reference: OSHA 29 CFR 1910.146)

Before entering tank:

1. Drain, flush, and ventilate tank interior.

2. Turn off engine and disconnect battery cables.

3. Continuously ventilate area or wear appropriate breathing apparatus.

4. Provide standby individual outside tank able to communicate with person inside and able to remove him with a lifeline if necessary.

FLYING MATERIAL HAZARD!

Wear eye protection around operating equipment.

Failure to comply will result in death or serious injury.

P/N 12686-01

DANGER

ELECTROCUTION

HAZARD!

DO NOT aim stream toward electrical lines.

Avoid spraying toward bystanders.

Failure to comply will result in death or serious injury.

P/N 11567

WARNING

SEVER HAZARD!

Keep hands clear!

Rotating fan and gears.

DO NOT operate without guards or doors in place.

Shut off engine, disconnect battery, and allow all moving parts to stop before servicing.

FLYING DEBRIS!

Wear eye protection around equipment.

Failure to comply could result in death or serious injury.

WARNING

P/N 31463

WARNING

BURN HAZARD!

Cooling system is under pressure.

Allow system to cool before handling.

Remove radiator cap slowly.

Wear appropriate safety gear.

Failure to comply could result in death or serious injury.

RADIATOR HANDLING INSTRUCTIONS

1. Use a 50/50 solution of water and antifreeze. Using 100% antifreeze will result in engine damage.

2. Check and replenish water prior to use. More water will be consumed when operating in hot conditions.

3. If overflow pipe begins emitting vapor, check and replenish water.

4. Remove and clean screen when dirty.

5. Check and clean fins periodically. Clogged fins will increase water consumption.

6. Protect radiator from fertilizer corrosion by washing radiator core with water.

P/N 31462

Do not operate without guards in place.

Failure to comply could result in death or serious injury.

P/N 12179

WARNING

FALL HAZARD!

All gates must be closed during operation.

Failure to comply could result in death or serious injury.

WARNING

BURN HAZARD!

Hot exhaust!

Stay back!

Failure to comply could result in death or serious injury.

012278

CAUTION

FALL HAZARD!

ALWAYS face ladder when mounting and dismounting.

Failure to comply may result in moderate or minor injury.

BURN HAZARD!

Contents could be under pressure.

DO NOT come in contact with material.

Ensure material in line is not hot before loosening clamps or opening valves.

DO NOT operate pump with both recirculation and discharge valves closed.

DO NOT use remote valve unless recirculation valve is open.

Excessive heat or bodily injury could occur.

Failure to comply could result in death or serious injury.

P/N 5216

OPERATION AND MAINTENANCE

MANUAL FOR

FINN TITAN280/TITAN330/TITAN400 HydroSeeders®

This manual gives you step-by-step instructions for the operation and maintenance of the FINN

HydroSeeder®. For best results and to ensure longer life of the equipment, please follow these instructions carefully. For your safety, read the entire manual before operating this unit.

DEFINITION OF HYDROSEEDING

Hydroseeding is the process whereby seed, fertilizer and/or lime, and wood fiber mulch (using water as a carrying medium) are applied on the soil to establish vegetation.

THE FINN HYDROSEEDER® AND HOW IT WORKS

The FINN HydroSeeder® will apply seed, fertilizer and/or lime, wood fiber mulch, or stabilizing materials in any prescribed or desired combination. The materials placed in the HydroSeeder® slurry tank are mixed with water and kept in suspension by a dual-agitation process, recirculation of slurry and mechanical agitation, thus forming a slurry that is pumped to the discharge assembly and directed onto the seed bed by the operator. This equipment is designed to accomplish hydroseeding in one easy operation with maximum efficiency.

MOUNTING THE HYDROSEEDER®

For speed and mobility of operation, the HydroSeeder® should be mounted on a truck or trailer.

However, it is important to select a carrier with sufficient capacity to handle the added weight.

DANGER

Pick-up hooks on HydroSeeders® are for lifting empty machines ONLY. Use appropriate spreader bar for the tank width. Ensure all capacities of lifting devices are rated for 15,000 lb

(6,800 kg) or greater. Failure to comply will result in death or serious injury.

DIMENSIONS, CAPACITIES, AND TRUCK REQUIREMENTS

CF Back of cab to end of frame

C Distance from HydroSeeder® front to

center of gravity

CA Back of cab to center of rear axle or

trunnion on tandem

F Front axle weight – Empty

FL Front axle weight – Loaded

G Distance from center of bogie to

HydroSeeder

center of gravity

HW HydroSeeder® weight

RE Rear axle weight – Empty

RL Rear axle weight – Loaded

WB Truck wheel base

TITAN280

English (Metric)

TITAN330

English (Metric)

TITAN400

English (Metric)

Truck GVW **

CA **

C (loaded)

C (empty)

OAL

HW (empty)

HW (water only)

HW (full load) ***

49,600 lb (22,320 kg)

120 in.

82 in.

122 in.

209 in.

11,690 lb

34,790 lb

38,350 lb

(304+ cm)

(208 cm)

(309+ cm)

(530+ cm)

(5,300 kg)

(15,780 kg)

(17,390 kg)

61,000 lb (27,669 kg)

157 in.

100 in.

134 in.

250 in.

12,340 lb

(398+ cm)

(254 cm)

(340+ cm)

(635+ cm)

(5,600 kg)

40,480 lb

(18,361 kg)

44,750 lb (20,300 kg)

64,000 lb

(29,029 kg)

170 in.

112 in.

150 in.

287 in.

13,180 lb

(431+ cm)

(284 cm)

(381+ cm)

(730+ cm)

(5,978 kg)

42,480 lb (19,268 kg)

46,750 lb (21,200 kg)

* These dimensions needed from the truck supplier as well as front axle capacity and rear axle capacity.

** Truck GVW depends on the truck weight. CA dimensions are approximate only, and depend on the front

and rear axle capacities, as well as the front and rear empty axle weights.

*** Weight of HydroSeeder®, water, and full charge of granular solids only. No auxiliary equipment or loads

included.

TRUCK MOUNTING CALCULATIONS

FE

FL

WB

CA

CF

OAL

RE

RL

(WB x FL) – (WB x FE) = G

WB x (RE + HW - RL.) = G

G + C must be equal to or less than CA

(WB x FE) + (G x HW) = FL

(WB x RE) + HW x (WB – G) = RL

Figure 1 – Truck Mounting Calculations and Dimensions

GENERAL MOUNTING GUIDELINES

A BODY GUIDE OF HEAVY ANGLE, SHOULD BE BOLTED

OR WELDED TO THE HYDROSEEDER® LEG NEAR THE

FRONT END OF THE TANK. IT SHOULD EXTEND BELOW

THE LEG AND CONTACT WEAR PLATE BOLTED TO THE

FRAME SIDE RAIL. THIS GUIDE RESTRICTS LATERAL

MOVEMENT OF TANK & THUS RELIEVES SHEAR STRESS

ON MOUNTINGS.

SHIMS MAY BE REQUIRED FOR

PROPER ALIGNMENT OF GUIDE

PLATE TO WEAR PLATE.

SLOTTED ANGLE ON TOP

WITH 1/2” THICK COVER

STRAP

MOUNTING

KIT

#011562

IMPORTANT:

INSURE THAT TUBES

ARE INSERTED TO PRE-

VENT FULL COMPRES-

SION OF SPRINGS WHEN

BOLTS ARE TIGHTENED.

3/16” GAP

3/8” x 6” WIDE MIN.-

WELD SECURELY TO

HYDROSEEDER®. BOLT

TO TRUCK CHASSIS.

FULL LENGTH SPACER THICK

ENOUGH TO COVER RIVET

HEADS; DRILL CLEARANCE

HOLES FOR RIVET HEADS

WHERE NEEDED.

WARNING:

DO NOT WELD OR DRILL

TRUCK FRAME IN THIS AREA.

5/8” GRADE 8 BOLT &

NUTS. - ALL PLACES.

Figure 2 – General Truck Mounting Guidelines

CAUTION

Your FINN HydroSeeder® should be mounted by a qualified truck body installer. Failure to comply could result in minor to moderate personal injury. Failure to comply could also result in product or property damage.

NOTICE

Mounting the HydroSeeder® to the truck must allow for tire clearance, as well as frame twist. Place

hard wood spacers along the length of truck rails or use FINN Spring Mounting Kit (number 011562) or equivalent. Also, two spring kits are required for the TITAN400.

ATTACHMENTS

1. Hose Reel: The live hose reel will mount on the HydroSeeder

or on the truck frame. The 200 ft

(61 m) capacity hydraulic rewind reel will wind up and store empty hose. A pivoting feature provides three locking positions, enabling curbside, 45 degree, and rear hose discharge. The entire hose reel is protected by a UV-protective canopy.

2. Hardened Pump Parts: Pump casing, impeller, and suction cover are treated with special material designed to resist wear.

3. Rear Spray Bar: The spray bar option is not designed for slurry application but for the dispersion of liquids for dust control, watering, feeding and washing applications. Rear spray bar is arranged so that operation is remotely controlled from the truck cab.

4. Radio Remote: The Remtron Remote is a Radio Frequency (RF) control system, designed to provide the machine operator with the ability to remotely operate equipment. The remote control system consists of two major modules: The transmitter (see Fig. 3) and the receiver. (see

Fig.4) The transmitter is designed with rocker switches for PUMP ON/OFF and THROTTLE

UP, THROTTLE DOWN (Decrease), and a red STOP button that kills the engine. With control of the engine throttle, the operator can precisely adjust the pump flow to whatever output the situation requires (i.e., for close-up work around buildings). The ability to remotely shut off the pump allows the operator to close the recirculation valve for increased performance during hose work. Carrying the remote valve at the end of the hose becomes unnecessary.

Figure 3 – Transmitter

Figure 4 – Receiver

NOTE:

For remote pump on/off control, the clutch cylinder must be connected to an air supply.

5. Air Flush System: The air flush option uses compressed air to purge any remaining mulch slurry from the HydroSeeder® hose, the discharge boom and the recirculation piping. To maximize performance, all discharge plumbing should be purged after every load. The air flush system provides a quick and easy means of purging without the need to acquire a flush tank and an additional water supply.

6. The second boom option enables spraying from both sides of the tank for larger spray areas without moving the vehicle. The dual discharge boom system can be operated simultaneously.

PRE-START CHECK

Safety check to ensure operator safety:

1. Check condition of all mounting hardware that secures HydroSeeder

to truck frame.

2. Make sure bag cutter is in place and secure.

3. Inspect all railings, ensuring they are all in place and secure.

4. Make sure that all guards are in place.

5. With the ignition switch ON, verify that the amber safety light, under the operator’s platform, is flashing.

EQUIPMENT CHECK

WARNING

Equipment check is made with the engine off and all rotating parts stopped. Failure to comply could result in death or serious injury.

1. See that tool kit contains all the prescribed items. See TOOL KIT on page 74.

2. Inspect slurry tank for foreign objects. See steps 2 and 3 in IV. MAINTENANCE of the

HYDROSEEDER® SAFETY SUMMARY SECTION on page 4.

3. Check fuel level.

4. Check the hydraulic oil level. See HYDRAULIC SYSTEM on page 29 for oil specifications.

5. Check engine oil level. For oil type refer to engine manual.

6. Check fluid level in radiator.

7. Inspect air cleaner for dust and dirt, clean if necessary.

8. Secure drain plug on the outside-bottom of slurry tank.

9. Check to be certain pump drain plug is in place.

10. Lubricate equipment. See LUBRICATION AND FLUIDS CHART on pages 30 and 31.

11. Engage and disengage clutch to determine if it snaps in and out.

12. Check and clean nozzle of obstructions.

13. Check pump discharge and recirculation valve handles for free movement.

14. Make sure all tank vents are clean and open. Do not plug or cap.

TWO-VALVE OPERATION

This HydroSeeder

is equipped with two independently operated ball valves to control slurry flow.

One is located in the recirculation line below the platform and the other is located in the discharge line above the platform. The valve handles should be positioned as shown in Figures 6 and 7 for the particular application required.

WARNING

Never engage slurry pump clutch when both valve handles are positioned as shown in Figure

5. Both valves are closed and will result in extreme heat generation that will cause damage or bodily injury if slurry pump is running.

DISCHARGE VALVE

(SHOWN CLOSED)

RECIRCULATION

VALVE

(SHOWN CLOSED)

Figure 5 – DO NOT Engage Clutch

TANK

1. DISCHARGE THROUGH BOOM:

Flow is through boom with no flow through closed recirculation valve (Figure 6). Flow through boom is controlled by engaging and disengaging slurry pump clutch.

NOTE:

Do not use the discharge valve to control distance. Valve should be completely open. Control the spray volume and spray distance by adjusting the engine

RPM.

FLOW

OPEN

CLOSED

POSITION

2. EXTENSION HOSE THROUGH BOOM:

Flow is through boom with no flow through closed recirculation valve (Figure 6). Extension hose is connected to boom and flow is controlled by engaging and disengaging pump clutch or by adjusting engine RPM.

TANK

RECIRCULATION

VALVE

(SHOWN CLOSED)

Figure 6 – Discharge Through Boom

DANGER

Do not use remote valve in this application. Failure to comply will result in death or serious injury.

3. EXTENSION HOSE OR HOSE REEL THROUGH REMOTE PORT:

Flow is through recirculation with no flow through closed discharge valve (Figure 7). Flow through hose is controlled by engaging and disengaging slurry pump clutch or by remote valve at end of hose.

An open recirculation valve allows flow back into tank when the remote valve is closed.

HANDLE IN

OPEN POSITION

CLOSED

TANK

FLOW

Figure 7 – Discharge Through Extension Hose or Hose Reel

DANGER

Ensure that the Recirculation valve must is open and material is flowing back into tank when using a remote valve, because a closed or plugged recirculation line will cause extreme heat.

Failure to comply will result in death or serious injury.

STARTING PROCEDURE

CAUTION

See HYDROSEEDER® SAFETY SUMMARY SECTION on pages 2 through 5 before operating the machine. Failure to comply could result in mild to moderate personal injury. Failure to comply could also result in product or property damage.

Before starting, open recirculation valve, close discharge and remote valves (if applicable), disengage

(turn off) clutch, and place agitator control in the NEUTRAL position.

1. Turn the key clockwise until the starter engages and the engine starts.

2. Allow engine to warm up for 3 to 5 minutes.

NOTE.

This engine has a safety system that will shut the engine off if the engine oil pressure drops below 7 psi (48 kPa) or if the water temperature reaches 230˚F (110˚C).

(optional)

Pump Control

Used to engage

Disengage the pump

Engine Throttle

Horn

Murphy View

Used for general engine data and warnings

Key

Switch

Emergency

Stop

Figure 8

POWERVIEW

The PowerView is a multifunctional tool that enables the operator to view many different engine parameters and service codes. A graphical back-lit LCD screen can display either a single parameter, or a quadrant display showing four parameters simultaneously. Diagnostic capabilities include fault codes with text translation for the most common fault conditions. The following relative engine parameters can be displayed in either English or Metric units, as well as in Spanish, French, or German:

• Engine rpm

AMBER

WARNING LED

RED SHUTDOWN

DERATE LED

• Engine Hours

• System Voltage

• % Engine Load at Current rpm

DISPLAY BEZEL

• Coolant Temperature

• Oil Pressure

• Throttle Position

MENU KEY ENTER KEY

• Active Service Codes

LEFT

ARROW KEY

(Scroll Up)

RIGHT

ARROW KEY

(Scroll Down)

Figure 9

–

Faceplate Features

Faceplate

The keypad on the PowerView is a capacitive touch-sensing system. There are no mechanical switches to stick or wear out. It can be operated in extreme temperatures, while wearing gloves, and is impervious to ice, snow, mud, grease, etc. When the key is touched, feedback is provided by flashing on the screen. The keys on the keypad perform the following functions (refer to Figure 9 page 12):

Menu Key

The Menu Key is used to either enter or exit the menu screens.

Left Arrow Key

The Left Arrow Key is used to scroll through the screen, either moving the parameter selection towards the left or upward.

Right Arrow Key

The Right Arrow Key is used to scroll through the screen, either moving the parameter selection towards the right or downward.

Enter Key

The Enter Key is used to select the parameter that is highlighted on the Screen.

POWERVIEW OPERATION

PowerView Menus (First Time Start-Up)

1. Once the engine has been started and the keyswitch is turned to RUN, the rpm Engine

Parameter is displayed. See Figure 10.

2. To toggle through the various engine parameters, touch either the Left or Right Arrow

Key.

3. To switch to the 4-UP DISPLAY, touch the

Menu Key to display the first seven items of the Main Menu. See Figure 11.

4. Since the first menu item listed is GO TO

4-UP DISPLAY, touch the Enter Key to select the four parameter display.

GO TO 4-UP DISPLAY

ENGINE CONFGURATION

STORED FAULT CODES

ADJUST BACKLIGHT

ADJUST CONTRAST

SELECT UNITS

SETUP 1-UP DISPLAY

0 2000 4000

1800 RPM

ENG RPM COOL TEMP

MENU

KEY

Figure 10 – 1-Up Display

0 RPM

ENG RPM

46F

COOL TEMP

0 PSI

OIL PRES

12.3 VDC

BAT VOLT

ENTER

KEY

Figure 11 – Main Menu

MENU

KEY

Figure 12 – 4-Up Display

Stored Fault Codes

The PowerView Display will store any fault codes generated by the engine, along with a text description. To access these fault codes:

1. Touch the Menu Key to display the Main

Menu.

2. Using the Right Arrow Key and toggle down the list until Stored Fault Codes is highlighted. See Figure 13.

3. Touch the Enter Key to view any stored fault codes. The display will respond by presenting a Requesting Fault Codes message, while the system retrieves the codes. See

Figure 14.

4. Once the stored fault codes have been retrieved, the initial code will be displayed along with a text description. See Figure 15.

GO TO 4-UP DISPLAY

ENGINE CONFGURATION

STORED FAULT CODES

ADJUST BACKLIGHT

ADJUST CONTRAST

SELECT UNITS

SETUP 1-UP DISPLAY

REQUESTING

ENTER

FAULT CODES

KEY

Figure 13 – Main Menu

5. If the word MORE appears at the bottom of the display, this indicates that there are additional fault codes being stored. Use the Right

Arrow Key to advance to the next code.

6. As long as the arrow in the display appears to the right of the word MORE as you advance through the fault codes, this means there are more codes available for viewing.

ENTER

KEY

Figure 14 – Access Stored Fault Codes

When the arrow in the display shifts to the left of the word MORE, this is an indication that you have accessed the final fault code being stored. At this point you can touch the Left Arrow Key to review the fault codes, or touch the

Menu Key to return to the Main Menu.

SHUTDOWN

WARNING

SPN110 FMI10

HIGH COOLANT TEMP

This Means There Are

More Stored Fault Codes

This Means There Are No

More Stored Fault Codes

MENU

KEY

TO REVIEW STORED

FAULT CODES

Figure 15 – Stored Fault Codes

AREA COVERAGE - MATERIAL CAPACITY

To determine the coverage per load for any HydroSeeder

, three questions must be answered prior to the application. First, is the job to be done a one-step process (which is when the seed, fertilizer, and mulch are applied proportionally per load) or a two-step process (which is when the seed and fertilizer are applied alone and then covered by mulch as a second operation)? Second, at what rates (usually in lbs per 1,000 sq. ft or lbs per acre) are the seeding materials to be applied? Finally, what are the loading capacities of the HydroSeeder

Application rates vary for different geographic locations, but in general, seed is applied at 6 to 10 lbs

(3 to 4 kg) to per 1,000 sq. ft; fertilizer is applied at a rate of approximately 400 lbs per acre; and fiber mulch is applied at 1,500 to 2,000 lb (680 to 907 kg) per acre. (Note: There are 43,560 sq. ft in an acre.) Local agronomists, agricultural extension agents, or soil and water conservation officials should be contacted for more specific information on application rates for a given area.

The following tables show loading versus coverage rates for the FINN T170 HydroSeeder

Table A shows rates for one-step applications. The coverage area is determined by the fiber mulch capacity of the HydroSeeder

and the rate at which it is applied. Table B shows the area coverage when seeding only, where little or no mulch is applied. The coverage area is determined by the granular solids capacity of the HydroSeeder

and the rate at which the solids are applied.

TABLE A – Using Seed, Fertilizer, and Mulch

Coverage Area in sq. ft (sq. m) Unit Amount of Material in Tank in lbs (kilograms)

Seed Fertilizer Mulch

TITAN280 287 (130) 333 (151) 1,250 (567) 36,300 (3,372)

TITAN330 345 (156) 400 (181) 1,500 (680) 43,560 (4,046)

TITAN400 414 (187) 480 (218) 1,800 (816) 52,272 (4,856)

Table is based on 1,500 lb (680 kg) of mulch, 400 lb (181 kg) of fertilizer, and 345 lb (156 kg) of seed at

8 lb (3.6 kg)/1,000 sq. ft per acre.

Table A Example: For TITAN330

1,500 lb (680 kg) Mulch per Tank

1,500 lb (680 kg) Mulch per Acre

= 1 Acre per Load

400 lb (181 kg) Fertilizer per Acre x 1 Acre = 400 lb (181 kg) Fertilizer per Load

345 lb (156 kg) Seed per Acre x 1 Acre = 345 lb (156 kg) Seed per Load

TABLE B – Seed and Fertilizer Only

Unit Amount of Material in Tank in lbs (kilograms) Coverage Area in sq. ft (sq. m)

TITAN280 3,136 (1,422) 3,600 (1,633) 6,736 (3,055) 392,040 (36,420)

TITAN330 3,485 (1,580) 4,000 (1,814) 7,485 (3,395) 435,600 (40,467)

TITAN400 4,140 (1,878) 4,800 (2,177) 8,940 (4,055) 522,720 (48,562)

9 (3.64)

10 (4.04)

12 (4.86)

Table is based on rates of 8 lb (3.6 kg) seed and 9.2 lb (4.2 kg) fertilizer per 1,000 sq ft

Table B Example: For TITAN330

7,485 lb (3,395 kg) Tank Capacity (Solids)

8 lb (3.6 kg) Seed + 9.2 lb (4.2 kg) Fertilizer per 1,000 sq. ft

= 435,600 sq. ft per Load

8 lb (3.6 kg) Seed

1,000 sq. ft

x 435,600 sq. ft = 3,485 lb (1,580 kg) Seed per Tank

Gallons

(Liters)

2,750 (10,410)

2,700 (10,220)

2,600 (9,840)

2,500 (9,465)

2,400 (9,085)

2,300 (8,705)

2,200 (8,325)

2,100 (7,950)

2,000 (7,570)

1,900 (7,190)

1,800 (6,815)

1,700 (6,435)

1,600 (6,055)

1,500 (5,675)

1,400 (5,300)

1,300 (4,925)

1,200 (4,545)

1,100 (4,165)

1,000 (3,785)

900 (3,405)

800 (3,025)

700 (2,650)

600 (2,270)

500 (1,890)

400 (1,515)

300 (1,135)

200 (755)

100 (375)

TITAN280 in. (cm) from top of load hatch

9 (22.9)

12.75 (32.4)

14.75 (37.5)

16.5 (41.9)

18.75 (47.6)

20.5 (52.1)

22.25 (56.5)

24.25 (61.6)

26 (66.0)

27.75 (70.5)

29.75 (75.6)

31.75 (80.6)

33.5 (85.1)

35.25 (89.5)

37 (94.0)

39 (99.1)

40.75 (103.5)

42.75 (108.6)

44.25 (112.4)

46 (116.8)

48 (121.9)

50 (127.0)

51.75 (131.4)

53.5 (135.9)

55.5 (141.0)

57.75 (146.7)

60 (152.4)

62.5 (158.8)

in. (cm) from bottom

58.5 (148.6)

54.75 (139.1)

52.75 (134)

51 (129.5)

48.75 (123.8)

47 (119.4)

45.25 (114.9)

43.25 (109.9)

41.5 (105.4)

39.75 (101)

37.75 (95.9)

35.75 (90.8)

34 (86.4)

32.25 (81.9)

30.5 (77.5)

28.5 (72.4)

26.75 (67.9)

24.75 (62.9)

23.25 (59.1)

21.5 (54.6)

19.5 (49.5)

17.5 (44.4)

15.75 (40)

14 (35.6)

12 (30.5)

9.75 (24.8)

7.5 (19.1)

5 (12.7)

Top of

Load Hatch

2,750 Gallons

10,400 Liters

TITAN280

Bottom

Gallons

(Liters)

3,300 (12,490)

3,200 (12,115)

3,100 (11,735)

3,000 (11,360)

2,900 (10,975)

2,800 (10,600)

2,700 (10,220)

2,600 (9,840)

TITAN330 in. (cm) from top of load hatch

9 (22.9)

13.25 (33.7)

14.75 (37.5)

16.5 (41.9)

18 (45.7)

19.75 (50.2)

21.25 (54.0)

22.75 (57.8)

Top of

Load Hatch

3,300 Gallons

12,490 Liters

TITAN330

Bottom

2,500 (9,465)

2,400 (9,085)

2,300 (8,705)

2,200 (8,325)

2,100 (7,950)

2,000 (7,570)

1,900 (7,190)

1,800 (6,815)

1,700 (6,435)

1,600 (6,055)

1,500 (5,675)

1,400 (5,300)

1,300 (4,925)

1,200 (4,545)

1,100 (4,165)

1,000 (3,785)

900 (3,405)

800 (3,025)

700 (2,650)

600 (2,270)

500 (1,890)

400 (1,515)

300 (1,135)

24.5 (62.2)

26 (66.0)

27.5 (69.9)

29 (73.7)

30.75 (78.1)

32.25 (81.9)

33.75 (85.7)

35.25 (89.5)

36.75 (93.3)

38.25 (97.2)

39.75 (101.0)

41.25 (104.8)

42.75 (108.6)

44.25 (112.4)

45.75 (116.2)

47.75 (121.3)

49 (124.5)

50.25 (127.6)

52 (132.1)

53.5 (135.9)

55.25 (140.3)

57 (144.8)

58.75 (149.2)

200 (755) 60.5 (153.7)

100 (375)

Figure 16 – Tank Capacity Chart (Sheet 1 of 2)

63 (160.0)

in. (cm) from bottom

58.5 (148.6)

54.25 (137.8)

52.75 (134)

51 (129.5)

49.5 (125.7)

47.75 (121.3)

46.25 (117.5)

44.75 (113.7)

43 (109.2)

41.5 (105.4)

40 (101.6)

38.5 (97.8)

36.75 (93.3)

35.25 (89.5)

33.75 (85.8)

32.25 (81.9)

30.75 (78.1)

29.25 (74.3)

27.75 (70.5)

26.25 (66.7)

24.75 (62.9)

23.25 (59.1)

21.75 (55.2)

19.75 (50.2)

18.5 (47)

17.25 (43.8)

15.5 (39.4)

14 (35.6)

12.25 (31.1)

10.5 (26.7)

8.75 (22.2)

7 (17.8)

4.5 (11.4)

TITAN400 in. (cm) from top of load hatch

28 (71.1)

29.5 (74.9)

30.75 (78.1)

32 (81.3)

33.25 (84.5)

34.75 (88.3)

36 (91.4)

37.25 (94.6)

38.5 (97.8)

39.75 101.0)

41 (104.1)

42 (106.7)

43.25 (109.9)

44.5 (113.0)

9 (22.9)

10 (25.4)

11.5 (29.2)

12.5 (31.8)

14 (35.6)

15.25 (38.7)

16.5 (41.9)

18 (45.7)

19.5 (49.5)

20.75 (52.7)

22 (55.9)

23.25 (59.1)

24.5 (62.2)

25.75 (65.4)

27 (68.6)

46 (116.8)

47.25 (120.0)

48.75 (123.8)

49.75 (126.4)

51 (129.5)

52.5 (133.4)

54 (137.2)

55.5 (141.0)

57 (144.8)

58.5 (148.6)

60.25 (153.0)

Gallons

(Liters)

3,975 (15,045)

3,900 (14,762)

3,800 (14,383)

3,700 (14,005)

3,600 (13,626)

3,500 (13,248)

3,400 (12,869)

3,300 (12,490)

3,200 (12,115)

3,100 (11,735)

3,000 (11,360)

2,900 (10,975)

2,800 (10,600)

2,700 (10,220)

2,600 (9,840)

2,500 (9,465)

2,400 (9,085)

2,300 (8,705)

2,200 (8,325)

2,100 (7,950)

2,000 (7,570)

1,900 (7,190)

1,800 (6,815)

1,700 (6,435)

1,600 (6,055)

1,500 (5,675)

1,400 (5,300)

1,300 (4,925)

1,200 (4,545)

1,100 (4,165)

1,000 (3,785)

900 (3,405)

800 (3,025)

700 (2,650)

600 (2,270)

500 (1,890)

400 (1,515)

300 (1,135)

200 (755)

100 (375)

in. (cm) from bottom

39.5 (100.3)

38 (96.5)

36.75 (93.3)

35.5 (90.2)

34.25 (87.0)

32.75 (83.2)

31.5 (80.0)

30.25 (76.8)

29 (73.7)

27.75 (70.5)

26.5 (67.3)

25.5 (64.8)

24.25 (61.6)

23 (58.4)

58.5 (148.6)

57.5 (146.1)

56 (142.2)

55 (139.7)

53.5 (135.9)

52.25 (132.7)

51 (129.5)

49.5 (125.7)

48 (121.9)

46.75 (118.7)

45.5 (115.6)

44.25 (112.4)

43 (109.2)

41.75 (106.0)

40.5 (102.9)

21.5 (54.6)

20.25 (51.4)

18.75 (47.6)

17.75 (45.1)

16.5 (41.9)

15 (38.1)

13.5 (34.3)

12 (30.5)

10.5 (26.7)

9 (22.9)

7.25 (18.4)

Top of

Load Hatch

3,975 Gallons

15,045 Liters

TITAN400

Figure 16 – Tank Capacity Chart (Sheet 2 of 2)

Bottom

NOTES

LOADING (FOR WOOD FIBER MULCH, IF LIMING SEE PAGE 27)

CAUTION

Take care not to lose pens, lighters, etc. from shirt pockets or drop pieces of paper or plastic bags into the tank. Failure to comply could result in minor to moderate personal injury. Failure to comply could also result in product or property damage.

1. With clutch disengaged (turned off) and agitator control in the NEUTRAL position, start engine and allow it to warm up. See STARTING PROCEDURE on page 12.

2. Start filling unit with water. When water reaches the top of the lower agitator shaft, move agitator control to full MIX position.

Fill the tank with water from any stream or pond using a fill pump. When filling from a pond or stream, be sure to use a suction strainer to filter out contaminants that could damage the pump and unit. Other sources of water that can be used are as follows:

A. Any pressure source, eg. fire hydrant. This unit is supplied with a 6 in. (15.2 cm) air gap fill port. Consult with local authorities before using water main in order to abide by all local ordinances.

B. Water tanker.

3. Piping System Cleanout Procedure (Purging Line):

A. Remove discharge nozzle and gasket from discharge boom.

B. Aim discharge boom assembly into an open area away from any persons, obstructions, or high voltage power lines.

C. Open discharge valve and close recirculation valve.

D. Increase throttle position to approximately 1/2 to 3/4 full.

E. Engage (turn on) clutch with a firm snap. Do NOT allow clutch to slip.

F. When discharge stream is clear, flush hose on reel (if applicable), open recirculation valve, and close discharge valve. After recirculation stream is clear, disengage (turn off) clutch.

G. Replace nozzle and gasket in discharge boom.

4. Continue filling tank with water.

5. Increase engine speed to full RPM. Governed speed of the engine on the FINN HydroSeeder® should be 2,550 to 2,600 RPM under load.

6. Start loading dry material, loading the lightest material first. Agitator control should be in full

MIX position for mixing.

A. Seed – Cut the seed bag open and dump contents into slurry tank. (When using inoculant, add it in the tank along with the seed.) When using quick-swelling seeds, load them just prior to application.

B. Wood Fiber Mulch – Empty the entire bag in, or cut bag open and drop in the sections of fiber. The amount of mulch to be used should be loaded by the time the water level is at 3/4 full. If agitator stalls or a high pitch squeal comes from the hydraulic system, reverse agitation to FORWARD for a moment to clear the obstruction, then return agitation to REVERSE.

CAUTION

Avoid jamming the agitator shaft for an extended period of time. Failure to comply could result in minor to moderate personal injury. Failure to comply could also result in product or property damage.

C. Fertilizer – Stand over hatch opening and drop the bag onto the bag cutter. Grasp both ends of the bag and dump material.

D. All other additives – Consult with manufacturer for proper loading technique.

7. When all materials are loaded and in suspension, and the tank is full, move the agitator to

NEUTRAL then full speed FORWARD to ensure all material is mixed. It may be necessary to change the agitator direction more than once to ensure a thorough mixture.

8. After material is thoroughly mixed, slow agitator in forward direction to 1/2 to 3/4 speed or enough to create movement in all of the corners of the tank. Do not over-agitate the slurry.

Always discharge the material with the agitator control in FORWARD position.

9. Close the hatch lid on the slurry tank.

NOTE:

The slurry should not be recirculated for more than 15 minutes prior to discharge to reduce wear and keep seed from swelling.

NOTE:

If foaming occurs, reduce agitator speed.

LOADING AND MIXING BFM, FGM, SMM, AND OTHER HIGHLY VISCOUS

SLURRIES

1. With clutch disengaged (turned off) and agitator control in the NEUTRAL position, start

engine and allow it to warm up. See STARTING PROCEDURE page 13.

2. Start filling unit with water using one of the sources of water listed below. When water reaches

the top of the agitator paddle blades, move agitator to full REVERSE position.

ACCEPTABLE WATER SOURCES

A. Water from any stream or pond using a fill pump. When filling from a pond or stream,

be sure to use a suction strainer to filter out any contaminants, which could damage

the pump and unit. Other sources of water are as follows:

B. Any pressure source, eg. fire hydrant. This unit is supplied with a 6 in. (15.2 cm)

air gap fill port, but it is necessary to consult local authorities before using water

main in order to abide by local ordinances.

C. Water tanker.

3. Piping System Cleanout Procedure:

A. Remove discharge nozzle and coupler gasket from the remote valve coupler at the

end of the discharge hose (or from boom on the platform option).

B. Aim discharge hose (or boom on the platform option) into an open area away from

any persons, obstructions, or high voltage power lines.

C. Open discharge and remote valves and close recirculation valve.

D. Open throttle to approximately 1/2 to 3/4 full.

E. Engage (turn on) clutch with a firm snap. Do NOT allow clutch to slip.

F. When discharge stream is clear, open recirculation valve and close discharge

valve. After recirculation stream is clear, disengage (turn off) clutch.

G. Replace coupler gasket in the remote valve coupler (or in boom on the platform

option).

4. Continue filling tank with water.

5. Increase throttle to 3/4 of full throttle.

6. Start loading dry material, loading the lightest materials first. Agitator control should be in

full REVERSE for mixing.

Seed - Cut open the seed bag and dump contents into slurry tank. (When using inoculant, add it in the tank along with the seed.) When using quick-swelling seeds, load them just prior to application.

BFM, FGM, SMM, and other highly viscous slurries - When the water level is above the top of the agitator blades, begin adding the entire bag of material into the tank.

It may become necessary to slow the rate of water being added to the tank. Add all bales before the tank is 3/4 full. If agitator stalls or a high-pitch squeal comes from the hydraulic system, reverse agitation to FORWARD for a moment to clear obstruction, then return agitator to REVERSE.

NOTE:

BFM, FGM, and other viscous slurries will entrain air if proper mixing procedures are not followed. Ensure that the agitator blades are completely submerged prior to the addition of this material. This will prevent air from entering the slurry.

50 lb (23 kg) of material to 125 gal (473 L) of water.

Fertilizer – Cut open the fertilizer bag and dump contents into slurry tank.

All other additives - Consult with manufacturer for proper loading technique.

7. When all materials are loaded and in suspension and the tank is full, move the agitator

to NEUTRAL then full speed FORWARD to ensure all material is mixed. It may be neces-

sary to change the agitator direction more than once to ensure a thorough mixture.

8. Agitate per the manufacturer’s recommendations. Generally, the agitation time is 10 min-

utes to allow the proper viscosity to be generated. Follow manufacturer’s recommendations.

Follow manufacturers suggested rates of materials as indi - cated on the packaging. Generally, this recommendation is

9. Once material is thoroughly mixed, place the agitator in FORWARD direction to 1/4 speed,

or just enough to create movement in all corners of the tank. DO NOT OVER-AGITATE the

slurry. Always discharge the material with the agitator control in FORWARD and at a slow

speed.

NOTE:

As the application process commences and the slurry level is decreased, which will expose the agitator blades, it is extremely important to ensure that the speed of the agitators

PRIOR TO APPLICATION

1. Operator should familiarize self with area to be seeded and develop a plan to ensure uniform application.

2. Develop a plan for communication between operator and driver of the carrying or towing vehicle to signal for start, stop, turn, etc. through the use of the signal horn.

3. Operator takes up position on the platform. From this point application will be controlled b. the use of the clutch, valve, discharge assembly, and throttle.

DISCHARGE NOZZLE SELECTION

Nozzles are stored in the tool box. This HydroSeeder

is equipped with 6 nozzles – two long distance and four fan nozzles. The smaller long distance nozzle is generally better suited for seed, fertilizer, and/or lime application while the large long distance nozzle is better for wood fiber mulch application. All of the fan nozzles are generally suited for both types of application.

Figure 17 – Nozzle Spray Dimensions

Nozzle Part Number

Lg. Long Distance 011775

Sm. Long Distance 012993

Sm. Narrow Fan

Sm. Wide Fan

012995

012994

Lg. Narrow Fan

Lg. Wide Fan

012997

012996

Distance (A)

Up to 320 ft (98 m)

Up to 150 ft (46 m)

Up to 75 ft (23 m)

Up to 45 ft (14 m)

Up to 90 ft (28 m)

Up to 50 ft (15 m)

Width (B)

15 ft (4.6 m )

25 ft (7.6 m)

23 ft (7 m)

35 ft (10.5 m)

APPLICATION OF SLURRY

I. GENERAL APPLICATION TECHNIQUES

DANGER

Do not spray toward power lines, transformers or other high voltage conductors. Failure to comply will result in death or serious injury.

CAUTION

The driver of the carrying vehicle should remain alert for hazards to the operator, such as low power lines, low hanging branches, etc. Driver should never start or stop abruptly.

Failure to comply could result in minor to moderate personal injury. Failure to comply could also result in product or property damage.

1. Determine which nozzle would best suit the application needs according to the DISCHARGE

NOZZLE SELECTION table on page 23.

2. Application of seed, fertilizer, and lime: Elevate discharge nozzle no less than 10 degrees above the area to be sprayed, allowing the slurry to gently rain onto the seed bed.

3. Application of wood and paper fiber: Whenever possible, aim the stream toward the ground to create a surface with small pockmarks, which will help get seed in contact with ground. Do not allow the stream to blast away the surface of the seed bed.

4. Generally, the most remote area of the seed bed should be covered first. Distance is controlled by engine speed and nozzle selection.

CAUTION

Do NOT partially close the valve to control the distance. Failure to comply could result in minor to moderate personal injury. Failure to comply could also result in product or property damage.

5. While moving along area to be seeded, the operator should move the nozzle back and forth in a slow, even arc.

6. If application is to be interrupted for a short period of time, disengage (turn off) clutch. If shutdown is going to be for an extended period of time (i.e., lunch break, reloading, etc.), close the valves to prevent slurry from dewatering. Re-engage (turn on) clutch to continue application.

7. To reduce foaming, it may be necessary to slow the agitator as the tank empties.

II. DISCHARGE THROUGH THE BOOM

1. Move the discharge valve handle to the OPEN position, the recirculation valve handle to the

CLOSED position, and engage (turn on) clutch. At this time, should the operator want to stop spraying for a short period, disengage (turn off) clutch; then re-engage (turn on) to continue spraying.

2. When the tank is empty, or when discontinuing discharge for an extended period of time, disengage (turn on) clutch, then immediately move the discharge valve to the CLOSED position, and idle the engine. This will maintain moisture in the discharge piping and help prevent plugging.

Move the agitator control to the NEUTRAL position.

III. PROCEDURES WHEN USING HOSES

Always pump clear water through the hose before pumping mulch. If the inside hose liner is dry, it will dewater the mulch, causing the hose to plug.

A. PUMP TAKE OFF SYSTEM OR HOSE REEL WITH REMOTE VALVE:

1. Open recirculation valve, close boom discharge valve, and close remote valve at the end of the hose.

2. Engage clutch. When stream is flowing freely through the recirculation line, open the pump take-off valve.

CAUTION

The high pressure on the hose can exert strong forces, causing the potential for the hose operator to lose control of hose or footing. The hose will require additional hose holders when this operation occurs on slopes. Open the pump take-off valve and the remote valve slowly and only after the hose operator is firmly positioned and has firm control of hose. Failure to comply could result in minor to moderate personal injury. Failure to comply could also result in product or property damage.

3. With the engine running at approximately 2,000 RPM, open the remote valve at the end of the hose to discharge the load.

4. When finished spraying, close the remote valve, disengage the clutch, and stop the engine. If using fiber mulch, retain as much water as possible in the hose by elevating the hose ends or by coupling the hose ends together.

5. If another load is to be done, see RELOADING PROCEDURE on page 26. If finished for the day, follow the clean-up procedures under DAILY on page 32.

DANGER

The recirculation valve must be open when using a remote valve. Failure to comply will result in death or serious injury.

B. EXTENSION HOSE SYSTEM - WITHOUT REMOTE VALVE:

1. Connect extension hose into the end of discharge boom.

2. A person controlling the end of the hose directs a second operator at the machine to control the clutch and adjust the engine speed.

CAUTION

Since the extension hose will be seeing the full output of the pump with the recirculation valve closed, the equipment operator and individual at the end of the hose should exercise extreme care when operating the unit on high pressure. The high pressure on the hose can exert strong forces, causing potential for the hose operator to lose control of hose or footing. The hose will require additional hose holders when operation occurs on slopes. Engage the clutch only after the hose operator is firmly positioned and has firm control of hose. Failure to comply could result in minor to moderate personal injury. Failure to comply could also result in product or property damage.

3. When hose operator is ready, signal the second operator to engage clutch and slowly increase the engine RPM until the desired discharge pressure is reached.

4. When finished spraying, disengage the clutch, stop the engine, and close the discharge valve.

If using fiber mulch, retain as much water as possible in the hose by elevating the hose ends or by coupling the hose ends together.

5. If another load is to be done, see RELOADING PROCEDURE on page 26. If finished for the day, follow the clean-up procedure described in DAILY CLEANING AND MAINTENANCE on page 32.

C. HOSE WORK WITH RADIO REMOTE TRANSMITTER:

1. Begin with the engine around 1/4 throttle (1,400 RPM).

2. Close recirculation valve. If using an extension hose connected to the discharge boom, open the discharge valve. If using the hose reel, close the discharge valve and open the pump takeoff valve to the hose reel.

3. Make sure all switches are in the OFF position and all dials are in the ZERO (0) position.

4. Switch Remote On/Off switch on the control panel to the ON position.

5. When the operator is in position, engage (turn on) pump using the remote transmitter and increase throttle to the desired output.

NOTICE

To quickly shut off the engine at any time, press the red E-Stop button on the transmitter. To restart the

engine, the key switch on the control panel must be returned to the OFF position and then restarted.

6. When finished spraying, turn the pump off and decrease the engine throttle to idle.

CAUTION

When using the radio remote control option, the secondary operator(s) must be aware that the machine can be activated remotely at any time after the Remote On/Off switch on the control panel is switched ON. If any maintenance or troubleshooting must be performed while the engine is running, the Remote On/Off switch must be in the OFF position. Failure to comply could result in minor personal injury, or product or property damage.

RELOADING PROCEDURE

1. Start at step 2 in LOADING on pages 21 and 22.

2. After last load of the day, refer to CLEANING AND MAINTENANCE on pages 32 and 33.

3. If the unit is equipped with an Air Flush System, refer to Air Flush System Parts and Operator's

Manual.

LIMING WITH THE HYDROSEEDER®

In using large concentrations of granular solids through the HydroSeeder®, it is advisable to keep the slurry moving through the pump at all times. This keeps the solids from settling in the lines and creating a clog. This unit was designed for the application of agricultural-grade lime or FINN HLL.

PROCEDURE

1. With clutch disengaged (turned off) and agitator control in the NEUTRAL position, start engine and allow it to warm up. See STARTING PROCEDURE on page 12.

2. Start filling the unit with water. When water reaches the top of the agitator shaft, move agitator control to approximately 1/2 speed in REVERSE.

3. Open both the recirculation and discharge valves.

4. Remove discharge nozzle and gasket from discharge boom.

5. Aim discharge boom assembly into an open area away from any persons, obstructions, or high voltage power lines.

6. Move the throttle to approximately 1/2 engine speed.

7. Engage (turn on) clutch and increase engine speed until you have reached maximum engine speed. A stream of water should be coming from the end of the recirculation pipe beside the hatch opening, as well as from the boom.

8. As soon as both streams are clear, close discharge valve and make sure water is being recirculated back to the tank.

9. Decrease throttle to 3/4 speed. Increase agitator speed to full REVERSE.

NOTICE

DO NOT DISENGAGE (TURN OFF) CLUTCH AT THIS POINT.

10. Twenty lb (9 kg) of granular solids displaces approximately 1 gal (3.8 L) of water. When filling the tank with water, the volume of granular solids must be accounted for. For example: If using the TITAN280 maximum recommended capacity of 8,000 lb (3,629 kg), 400 gal (1,514 L)

(8,000/20 = 400) would have to subtracted from the total tank capacity, thus, 2,750 gal ( 10,410

L) – 400 gal (1,514 L) = 2,350 gal (8,896 L). For the TITAN330 maximum recommended capacity of 10,000 lb (4,536 kg), 500 gal (1,893 L) (10,000/20 = 500) would have to be subtracted, thus, 3,300 gal (12,492 L) – 500 gal (1,893 L) = 2,800 gal (10,599 L).

11. Fill the tank to the required capacity for the rate of granular solids to be applied.

12. Load the material (see LOADING pages 21 and 22, steps 5 through 8).

13. When ready to apply slurry, install gasket and nozzle into boom.

14. Move agitator control to 3/4 speed, FORWARD.

15. With the clutch still engaged (turned on), open discharge valve.

CAUTION

To decrease pump wear and increase discharge distance, it may now be desirable to close the recirculation valve. However, the recirculation valve must be open BEFORE closing the discharge valve if the application of slurry is to be interrupted. Failure to comply could result in minor to moderate personal injury. Failure to comply could also result in product or property damage.

16. Apply the slurry. See APPLICATION OF SLURRY on page 24.

17. If another load is to be applied, start again at Step 1. If finished, refer to CLEANING AND MAIN-

TENANCE on pages 32 and 33.

TROUBLESHOOTING YOUR HYDROSEEDER®

Because of the tremendous work load usually placed upon the HydroSeeder

, minor malfunctions will occur from time to time. If these are not remedied immediately, they could lead to poor performance and damage to the equipment. This section describes symptoms, possible causes, and the corrective action(s) to take.

1. Foam in the tank and air entrainment:

The mixture of dry materials with water will sometimes cause excessive foaming, while other dry materials with water mixtures will cause air entrainment. These situations will reveal themselves with the occurences of an erratic slurry discharge, a drop in the pressure of the discharge, and a drop-off in distance of slurry discharge.

Some solutions are:

A. As slurry level drops in the tank, slow the agitator.

B. Add 2 to 3 oz (6 to 9 cl) of an antifoaming agent to tank.

C. If you can determine which additive is causing the air problem, either add it last or not at all – unless it’s the water.

D. Limit recirculation time as much as possible.

2. Plugging or clogging:

DANGER

Turn off engine and disconnect battery cables before working on equipment. Failure to comply will result in death or serious injury

Sometimes, when a stoppage occurs, you will not be able to find anything in the line. When this happens, it means that the system became airbound instead of plugged. To remedy this, see

FOAMING OF SOLUTION AND LACK OF DISTANCE on pages 30 and 31. Plugging can occur in any one of four places: the valve and recirculation nozzle, the discharge nozzle, the pump area, and the sump area. The plugging is caused by either foreign objects or dewatered mulch.

A. Obstruction in the discharge nozzle is determined by a change in or stoppage of the spray pattern.

1. Disengage (turn off) clutch.

2. Make certain that pump has stopped rotating.

3. Slowly and carefully remove nozzle.

4. Using the nozzle cleaning rod attached to the underside of the guard rail, clear the nozzle.

DANGER

Severe injury can result from opening clamps when piping is hot. Before loosening any clamps, determine if the pipe is hot. If so, let it cool before attempting repair. Failure to comply will result in death or serious injury.

B. If the recirculation system is not working:

1. Disengage (turn off) clutch and shut down engine.

2. Remove two clamps on each side of the recirculation valve.

3. Slide rubber seals back and remove valve assembly.

4. Check valve assembly, recirculation nozzle in the discharge pipe, and the recirculation pipe going into tank. Clear any obstructions.

5. Replace valve assembly and slide the seals back into place. Lubricate the outside of the seals.

6. Replace the clamps.

3. Obstruction in the pump, (determined by a drop in pressure). If the drop in pressure is accompanied by a frothy or whitish discharge stream, the blockage is in the suction line or sump area.

To clear the pump:

A. Disengage (turn off) clutch and stop the engine.

B. Loosen the suction pipe clamps. If there is material in the tank, shut off the suction line valve.

C. Remove the clamp closest to the pump.

NOTE:

If no water comes out, obstruction is in sump area.

D. Reach into the pump and remove the obstruction. If jammed, the pump suction cover may need to be removed.

E. Reassemble, removing pipe plug in the process.

F. Open suction line valve.

4. Obstruction in sump area (located at the bottom of the tank on the inside where the suction pipe is attached).

A. Easiest: To clear the sump area: Backflush through the discharge plumbing with the water supply hose.

B. Another method: Remove the drain plug and run a long pole through the opening and into the sump area. Remove the obstruction and replace the drain cap.

NOTICE

Do not turn the shaft backward with a pipe wrench. This will unscrew pump impeller from pump shaft.

Consequently, when clutch is engaged (turned on), the pump impeller will screw onto pump shaft with a force great enough to break pump impeller.

TROUBLESHOOTING YOUR HYDROSEEDER®

Problem

LEAKS:

Probable Causes

Tank Bearing

Pressure Pipe Clamps

Suggested Solutions

Lack of lubrication – seal worn Replace seal and follow lube

Bolts not tightened schedule. Tighten uniformly to 25 lb-ft (34 N•m).

Rubber seal cracked, pinched, Replace; always grease seal before or torn.clamping shut.

Suction Pipe Clamps

Discharge Swivels

Pump Shaft

Pump Suction Cover

Rubber seal cracked, pinched, or torn

Not greased often enough

Pressure lubricator not serviced

O-ring bad

Replace; always grease seal before clamping shut.

Rebuild swivels w/repair kit (partnumber 012397, qty. 2 required).

Replace pump seal. Service automatic pressure lubricator daily. See page 10.

Replace O-ring; use grease when replacing.

Discharge Boom or Nozzle

Camlock Fittings

Worn or no gasket

MACHINE JUMPS DURING OPERATION:

Agitator Agitator bent by heavy object falling on it

Bent Paddles Loading wood fiber mulch into tank before tank is half full

FOAMING OF SOLUTION AND LACK OF DISTANCE:

Pump loses prime, lacks distance, leaves excessive amount in tank

–100 gal (378 L) or more

Sucking air in suction lines

Replace gasket.

Straighten agitator or shim so it runs true.

Straighten agitator paddle; realign agitator to run true.

Check all suction connections to ensure that rubber seals are in good condition. Grease seals before replacing.

Air entrainment See TROUBLESHOOTING step 1 on page 20.

See authorized engine dealer.

Low engine RPM (Below 2,750

RPM – No load)

Soft water

Too much agitation

Pump worn

Suction partially plugged

Nozzle worn or plugged

Fertilizer

Clutch slippage

Slow the agitator.

Reset pump tolerance. See page

30.

Clean out machine. See pages pages 28 and 29.

Clean nozzles; replace if necessary

Change type.

Readjust clutch. See clutch manual.

VALVE:

Valve stuck

Constant plugging during loading and discharging

Extension hose plugs after use

Frozen

Constant plugging during operation Foreign material in slurry

Thaw out ice and lubricate; leave in discharge position during storage.

Drain and clean out tank; check storage for foreign materials.

Reinstruct your operator. See pages 19 and 20.

Loading HydroSeeder® before tank is half full of water

Incorrect loading procedure

Improper operation by operator

Clutch slipping

Not moving valve handle far enough

See pages 19 and 20.

Reinstruct your operator. Review

OPERATOR’S MANUAL.

Readjust clutch. See manual.

Valve should be fully open.

Machine not being flushed out prior to reloading

Machine not being run at correct

RPM during loading

See page 19.

Reinstruct your operator. See page

19.

Letting water run out, leaving wood fiber mulch to dry out

If hose has to be uncoupled, seal hose ends, to keep water in hose and prevent wood fiber mulch from drying out.

CLUTCH:

Does not pull load or overheats Out of adjustment

Jumps out of engagement Too loose or too tight

Readjust clutch. See clutch manual.

PUMP:

Excessive wear

Will not turn

Fertilizer with highly abrasive fillers Change fertilizer – avoid abrasive fillers.

Overloading machine with dry material

Too much time allowed between loading and discharging

Load machine to recommended capacities.

After loading and mixing has been completed, set agitator at 1/2 speed in REVERSE and disengage pump.

Recirculating all the time

Frozen

Jammed with fertilizer or lime

Impeller rusted to suction cover plate

Close recirculation valve when discharging through the boom.

Warm housing to melt ice.

Remove cover and clean interior.

Pull cover and remove rust.

CLEANING AND MAINTENANCE

AFTER FIRST 4 TO 8 HOURS OF OPERATION

1. Check and adjust clutch. See clutch manual.

DAILY:

1. Cleaning the HydroSeeder

A. Fill slurry tank to center of agitator shaft with clean water.

B. Move agitator lever to full speed to flush off inside of tank top and walls.

C. Remove discharge nozzle and gasket from discharge boom.

D. While pointing discharge toward an open area, move discharge valve handle to DIS-

CHARGE position and engage (turn on) clutch. Allow to discharge until clear water is coming out.

E. Move recirculation valve handle to RECIRCULATION and allow to run momentarily.

F. Disengage (turn off) clutch, idle the engine, move valve handle to DISCHARGE position, move agitator handle to NEUTRAL, and turn off engine.

G. Always remove drain plug and allow the tank to drain.

H. In freezing weather, leave main tank drain plug out and remove pump drain plug. Move all slurry valves to OPEN position.

I. Wash the outside of the HydroSeeder

, including the radiator, to remove any corrosive materials.

J. If using lime, daily maintenance should be performed after every load.

K. Clean out extension hoses.

L. Make sure all tank vents are clean and open. Do not plug or cap.

2. Lubricating the HydroSeeder

– See LUBRICATION AND FLUIDS CHART on pages 38 and

39.

NOTICE

Lubrication should be performed IMMEDIATELY AFTER cleaning of equipment. Engine not running.

A. Lubricate the agitator shaft bearings located on the outside front and rear of slurry tank.

B. Service the automatic pressure lubricator on pump as needed.

C. Check the engine oil and replenish when necessary. Change oil and filter after first 100 hours, then every 250 hours thereafter. Consult the Engine Operator’s Manual for the correct grade of oil and the engine break-in procedure.

D. Lubricate the swivel on the discharge assembly and the swivel on the hose reel.

E. If equipped with the Air Flush Option, refer to the Air Flush System Manual.

WEEKLY OR EVERY 40 HOURS OF OPERATING TIME:

1. Clean the air cleaner following the instructions in the Engine Operator’s Manual.

2. Lubricate all the points on the HydroSeeder

as outlined in DAILY. Additionally, lubricate the four grease fittings on the clutch/pump.

3. Check the level in the hydraulic oil reservoir; maintain level at sight gauge.

4. Check the clutch adjustment to ensure that it “snaps” in and out of engagement. Adjust the clutch with the engine off.

5. Check antifreeze in radiator. Add antifreeze as required.

6. Inspect the slurry tank for buildup of residue in the suction area and clear if necessary.

7. Check and clean engine radiator. Flush with clear, low-pressure waterspray and blow dry with compressed air. Do NOT use high-pressure water spray.

8. Check pivoting hose reel swivel bolt. Ensure proper torque. Replace bolts if any show signs of wear.

9. Check oil level in agitator gear boxes. Refer to Maintenance Chart.

SEASONAL AND WINTER STORAGE MAINTENANCE:

1. Drain the slurry tank of all water, prior to storage, and leave the drain plug uninstalled.

2. If possible, cover machine with tarp or park inside of an enclosure.

3. Store the HydroSeeder

with all slurry valve handles in the open position. To prevent damage from freezing, it is advisable to remove all slurry valves and store in a heated area.

4. Pour 1 qt (0.95 L) of mineral oil or environmentally safe lubricant into the pump housing and spin pump by hand to prevent rust in the pump. Remove drain plug.

5. Chip and steel-brush any interior rust spots in the slurry-tank and touch up with paint. See numbers 2 and 3 in IV. MAINTENANCE of the HYDROSEEDER® SAFETY SUMMARY SECTION on page 4.

6. Lubricate all fittings.

7. Check antifreeze in radiator. Add antifreeze as required.

8. Lubricate equipment again just prior to putting into operation after having been in storage.

10. Change hydraulic oil and filter. (500 hours)

11. Disconnect battery cables. In cold weather, remove battery and store it in a safe, warm place.

12. Add fuel stabilizer to fuel tank.

HYDRAULIC SYSTEM

The hydraulic system on your FINN HydroSeeder® is designed to give trouble free service, if maintained. The most important areas of maintenance are the hydraulic oil and filtration. The reservoir holds 60 gal (227 L) of Mobil DTE-13M or equivalent hydraulic oil.The hydraulic oil should be replaced per the lubrication schedule or if the oil becomes milky or it gives off a burnt odor. The hydraulic oil filter must be replaced on schedule with a 25 micron absolute filter (FINN part number 011869). The hydraulic system relief is factory set at 3,200 psi (22,063 kPa).

CLUMP MAINTENANCE SECTION

CAUTION

Clump maintenance should be done only while engine is not running and battery cables are disconnected. Failure to comply could result in minor or moderate personal injury. Failure to comply could also result in product or property damage.

NOTE: Refer to Figure 18 on page 36 for all in-text callouts

on pages 34 and 35.

A. FACTORY TOLERANCES

1. To check clump tolerances, loosen the two clamps on the pump suction piping and remove the inlet elbow. Through the pump suction hole, insert a feeler gauge between impeller (3) and suction cover (1). This measurement on a new clump is between 0.30 to 0.40 in. (.750 to 1.00 mm).

B. IMPELLER CLEARANCE

NOTICE

Tightening of the bolts should be performed in a criss-cross pattern. DO NOT TIGHTEN OVER 15 lb-ft

(20 N•m). Overtightening will crack the flange of the pump suction cover.

TO BRING THE CLUMP BACK TO PROPER TOLERANCE, PROCEED AS FOLLOWS:

1. Loosen twelve bolts (16) and push pump housing (1) into seal housing (6) until it hits the impeller (3). Impeller should be in full contact with pump housing.

2. Tighten bolts (17) finger tight. Impeller (3) should rub the wear plate (2) and not turn easily through one revolution.

3. Tighten bolts (16) hand tight until they touch pump casing (1).

4. Back off bolts (17) 2 turns.

5. Tighten bolts (16) 3/4 turn and tighten nuts (14) to 15 lb-ft (20 N•m).

6. Tighten bolts (17) to 15 lb-ft (20 N•m). Clearance gap should be about 0.040 in. (1.00 mm).

Check to see if impeller (3) turns freely through one revolution.

C. CLEANING

1. To clean impeller (3), loosen the two victaulic pipe clamps and remove the suction pipe assembly. The eye of the impeller (3) can then be seen through the pump housing (1) and is readily accessible for cleaning.

2. To remove impeller (3), loosen and remove the two victaulic clamps and remove the discharge pipe. Remove twelve bolts (17) that hold pump casing (1) in place. Exercise caution while removing the pump casing (1) because it is heavy (approximately 150 lb [68 kg]) and the O-ring

(5) can easily be damaged.

3. Lock the shaft (19) in place with a pipe wrench. Using a block of wood as a transfer, hammer at the edge of the impeller vane to turn the Impeller (3) counterclockwise. Once the impeller is free, it can be turned by hand. Be careful not to drop it as it fully disengages from the shaft threads.

CAUTION

Do not turn the shaft backward with a pipe wrench. This will unscrew pump impeller from pump shaft. Consequently, when clutch is engaged (turned on), the pump impeller will screw onto pump shaft with a force great enough to break pump impeller. Failure to comply could result in minor or moderate personal injury. Failure to comply could also result in product or property damage.

D. INSTALLING NEW SEAL ASSEMBLY (9)

(Do not unwrap the new seal assembly until you are ready to install. All parts of the assembly are packed in sequence of installation.)

1. To replace clump shaft seal assembly (4), perform the operations under CLEANING on page 34.

2. After cleaning all parts, including clump shaft (19), begin reassembly of clump. Using a light oil lubricant (such as 3-in-1 oil), install the ceramic seat, making sure that the notch on the ceramic seal is lined up with the pin at the bottom of the clump mounting plate (12). Lubricate inside of the bellows assembly with a light oil lubricant and check to make sure the steel ring is stuck

(glued) to end of assembly. Slide bellows assembly onto the shaft and push until steel ring is against ceramic seat.

3. Install the seal spring on the hub of impeller. After coating the threads on the clump shaft (19) with an antiseize compound, install impeller (3), seating it securely.

4. Utilizing O-ring (5), reinstall pump casing (1) using twelve bolts (17). At this time, check to see that the clump runs freely. If impeller (3) rubs cover plate, you do not have impeller tight on clump shaft (19) or pump casing (1) needs to be readjusted. See IMPELLER CLEARANCE on page 34. Tighten bolts uniformly using 15 lb-ft (20 N•m) on the torque wrench.

5. After reinstalling the suction pipe assembly, lubricate and tighten the victaulic clamps. Service the automatic lubricator.

55 Pressure Lubricator

Pressure Lubricator

NOTE:

Item #34 (10¨ Clutch

Assembly Kit) Includes

Items #35-51)

17 16 15

FIGURE 18

CLUMP ASSEMBLY

Description

Ref. No.

Part Number

012976

012879-1B

012976-02

013131

Impeller

Clump Shaft Seal

No. Required

100042

100040

005574-02

012783

100321

100030

100031

100332

100224

100029

100026

100032

100013

100028

100341

100003

100011

022314

100008

100019

100018

100009

013132

013126

012733

013163

013128

0WF12SAE

10OY12

00WL12

0X1232

0X1228

012734

013133

012731

012732

013047

F400-0046

012765

005570

012695

F400-0060

013154

000427

100323

100308

100307

022314

002383

008190

007954

008189

AS568B O-Ring #455

Seal Housing Machining

Seal

Clump Mounting Plate Machining

3/4 SAE Flat Washer

3/4-10 UNC Hex Nut

3/4 Lock Washer

3/4-12 UNC HHCS x 2" Lg.

3/4-12 UNC HHCS x 1-3/4" Lg.

Bearing Retainer Ring

Bearing

Nut

1-1/2" Bore Cylinder, 4" Stroke

Clump Name Plate

Make From F5430-01 Casting

Cluch Handle Spacer

Clutch Handle Modification

Handle Grip Black

Modified Clutch lever

10 in. Clutch Assembly

External Snap Ring

Internal Snap Ring

Release

Adjusting Ring Plate

10 in. Clutch Disc

Driving Ring Lever Kit

Retaining Ring

Connecting Link

Release Lever

Clevis Pin

Lockwasher

Screw, Nut, Follower, and Spring

Spring

Plunger

LUBRICATION LOCATIONS

Ref. No.

LUBRICATION AND FLUIDS CHART

Lubricant Frequency Location

Check Clutch Lever Bearings

Grease Agitator Shaft Bearings

Check Fuel Level

Grease Discharge Swivels

Check Engine Oil Level

Check Engine Oil and Filter

Grease Pump Bearings

Check Hydraulic Fluid Level

Change Hydraulic Fluid and Filter

Check Agitator Gearbox Level

Change Engine Coolant

Number

Weekly

Daily

See Engine Manual

See Pump Manual

Weekly 1

Seasonally or 500 Hours 1

See Gearbox Manual

Seasonally

LUBRICANT OR FLUID USED

MO See Component Manual

HO Mobil DTE-13M or Equivalent Hydraulic Oil

AF 50/50 Antifreeze and Water Mixture

TIME KEY

DAILY (8 hours)

WEEKLY (40 hours)

SEASONALLY (500 hours)

SEE COMPONENT MANUAL

FLUID CAPACITIES

Fuel – 38 gal (144 L)

Hydraulic Oil – 60 gal (227 L)

Engine Coolant – 5 gal (19 L) 50/50 Mix Only

Engine Oil – See Engine Manual

NOTES

TITAN280/TITAN330

TITAN400

HydroSeeder

®

Parts Manual

Mode. MO

CONTROLS

Pages 60-61

CLUTCH

(Pages 54-55)

CONTROL BOX

WIRING

PICTORIAL REFERENCE

STRUCTURE AND

RAILING TITAN280

TITAN330 TITAN400

Pages 44-45

HATCH VIEW

Pages 46-47

AGITATOR AND

SEAL ASSY.

Pages 70-71

HYDRAULIC

SYSTEM

Pages 74-75

HYDRAULIC

Pages 50-51

PARTS

Pages 53-53

DISCHARGE

BOOM ASSY.

GROUND

LEVEL CONTROLS

Page 68

HOSE REEL

ASSEMBLY

Pages 78-79

PUMP ASSEMBLY

Pages 56-57

2ND DISCHARGE

OPTION ASSY.

Pages 58-59

STRUCTURE AND RAILING

SEE FUEL TANK

DETAIL

(On Page 37)

SEE POLY HATCH DETAIL

3 2

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

STRUCTURE AND RAILING TITAN330/TITAN400

Ref. No. Part Number Description

012919

F400-0015

012771

012918

F400-0012

013149

013122

013150

013168

F400-0013

012912

005613

012750

008470

13 005700

14 012515

15 012895

16 011741

17 055336

18 012916

19 F400-0016

F280-0005

012914

012737

FW71225

22 F330-0082

23 012705

24 F330-0124

F400-0004

012913

F400-0014

27 F400-0030

28 012514

29 005613

30 012977

31 F400-0002

F400-0009-03

F400-0009-04

F330-0078

005619

34 041371

35 005726

36 012693

37 012694

Rear Right Corner Rail

Long Rear Toe Rail

Hand Rail

Rear Guard Rail

Left Corner Rear Toe Rail

Swing Gate Weldment

Rear Corner Guard Rail

Left Rear Rail Extension

Left Rear Toe Rail

Left Rear Guard Rail

Fill Stack Extension

Fill Port Plug

1-1/4 in. Pipe Plug

3 in. Fill Port

3 in. Male Brass Adapter

U-Bolt

Front Side Toe Rail (TITAN400)

Front Side Toe Rail (TITAN280,TITAN330)

Front Side Guard Rail (TITAN400)

Front Side Guard Rail (TITAN280,TITAN330)

Slide Gate Snapper Pin

Front Rail

Front Gaurd Rail

Tank Top Extension (TITAN400)

Tank Top Extension (TITAN280,TITAN330)

Right Rear Guard Rail

Right Rear Toe Rail

Square U-Bolt for 1-1/2 in. Square Pipe

Main Tank Top

Narrow Tank Top Support

Wide Tank Top Support

Tool Box Mount

U Bolt For 1-1/4 in. Round Pipe

Dust Cap w/Gasket-Main Tank Drain

No. Required

3 (280) / 2 (330) / 6 (400)

0 (280) / 2 (330) / 2 (400)

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

HATCH VIEW

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

HATCH VIEW

Ref. No.

Part Number

012909

070627

012903

012938

012834

002909

005433

Description

Hatch Lid Weldment

Lid Hinge Weldment

Hatch Liner Weldment

Safety Cross Strap Weldment

Bag Cutter Stainless

Handle

Latch

No. Required

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

DISCHARGE BOOM ASSEMBLY

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

DISCHARGE BOOM ASSEMBLY

TITAN280/TITAN330/TITAN400

Ref. No.

Part Number

012898

12900-01

012896

012897

013159

012888

013043

011914

012886

Description

3 in. Discharge Boom Assembly

Boom Stand Pipe

Upper Boom Discharge Weldment

Lower Boom Discharge Weldment

Titan Boom Handle

3 in. Straight Swivel

3 in. Swivel Repair Kit

Black Knob/Set Screw

3 in. Coupler

No. Required

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

ENGINE AND RADIATOR

FOR RADIATOR PARTS

REFER TO PAGES 44-45

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

Ref. No.

ENGINE AND RADIATOR

Description Part Number

013107

013036

055498

052022-05

075247

052012

055367

013135

Cummins Tier III Engine

Radiator / Charge Air Cooler

013135-S Safety

022657

013157

045014

013067

013068

3-1/2 in. Rain Cap

Rear Engine Riser Weldment

Front Engine Riser Weldment

013065

013069-03

013069-01

013077-01

013077-02

F400-0037

075206

CU-FF5612-01

012980

F400-0064-01

F400-0064-02

F400-0059

Rear Engine Foot

Front Engine Foot - L.H.S.

Lower Muffler Mount

Upper Muffler Mount

Rubber Stud Mount

Main Fuel Filter

Cummmins Muffler Clamp

Rear Engine Panel Mount - RHS

Rear Engine Panel Mount - LHS

Air Cleaner Mount

*CU-FF5612 Remote Fuel Filter

*CU-LF3970 Oil

No. Required

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

RADIATOR PARTS

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

Ref. No.

RADIATOR PARTS

Description Part Number

CUM11000378 90º Elbow Fitting

CUM80000207 Hose

CUM50000491

CUM50000499

3/4 in. Heater Hose

3/8 in. Heater Hose (Not Shown)

CUM10000737 Blower

CUM3910128 Spacer

CUM50000887

CUM50000437

CUM80000435

Large Charge Air Cooler Tube

Charge Air Cooler Hose 3 in. ID

2-1/2 in. Charge Air Cooler Clamp

CUM50000886

CUM50000600

CUM80000220

CUM50000606

CUM50000605

Small CHarge Air Cooler Tube

Charge Air Cooler Hos. 2-1/2 in. ID

3 in. Charge Air Cooler Clamp

Upper Radiator Hose

Lower Radiator Hose

No. Required

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

CLUMP, PIPING, AND DISCHARGE ASSEMBLY

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

CLUMP, PIPING, AND DISCHARGE ASSEMBLY

Ref. No. Part Number Description

1 011727-09 Recirculation

2 011727-10 Recirculation

3 011727-11 Recirculation

4 012316

5 012385 6 in. Victaulic Elbow

6 012726-03 Recirculation

7 013145

8 012900-05 Suction

9 012083 1-1/4 in. Stainless Steel Ball Valve

012971 Handle

012902

012922

3 in. Stainless Steel Ball Valve

RH Discharge Valve Stand Pipe

013152

012932

013148-01

013148-02

012961-01

012961-02

Titan Discharge Pipe

Pump Flange Weldment

Suction Valve Outlet

Pump Suction Inlet

Suction Pump Gasket

Pump Discharge Gasket

160259

160266

002438

002439

041368

041368G

041369

05703-02

006721

006722

080555-06

070122

160301

1/2 in. Pipe Cap

3 in. Pipe Cap

3 in. Victaulic Clamp

Clamp Seal

6 in. Victaulic Clamp

Clamp Seal

6 in. Knife Gate Valve

1-1/4 in. Coupling Deflector Weldment

1-1/4 in. Pipe Clamp

Clamp Seal

Suction Valve Pipe (GOE/TOE)

1/2 in. Ball Valve

1/2 in. Standard Close Nipple

No. Required

1 Per

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

PUMP ASSEMBLY

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

PUMP ASSEMBLY

Ref. No. Part Number Description

013135

1 013134 Titan Clump Casing

2 012976-02 Impeller

013132

013131

5 013126

Titan Clump Casing Seal

Titan Clump Shaft Seal

160389

160162

8 160082

9 002383

10 013163-01

3/8 in. Nipple x 2 in. Lg.

3/8' Xtra-Heavy Coupling

3/8 in. 45 Deg. Street Elbow

013128

012733

013133

14 012734

15 012731

16 007705

Titan Clump Gasket

Titan Clump Mounting Plate

Seal

Titan Clump Shaft

Bearing Retainer Ring

17 005570

18 012695

19 012732

20 012783 10 in. Clutch Assembly

21 100308 Lock

22 100307 Drive Nut

031219

F400-0060

Modified Clutch Lever

Clutch Handle Spacer

013154

000427

Titan Clutch Handle

Black Grip Handle

No. Required

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

2ND DISCHARGE BOOM ASSEMBLY

Ref.

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

2ND DISCHARGE BOOM ASSEMBLY-OPTIONAL

Ref. No. Part Number

012900-04

012902

012921

002438

002439

002868

080555-06

7 080739

Description

Long Boom Connector Pipe

3 in. Stainless Steel Ball Valve

LH Discharge Valve Stand Pipe

3 in. Victaulic Clamp

Clamp Seal

3 in. Victaulic Elbow

Suction Valve Pipe (GOE, TOE)

No. Required

1 Per

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

CONTROLS

VIEW B

VIEW A

VIEW B

VIEW A

SEE CLUTCH PARTS

ON PAGES 54-55

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

CONTROLS

Ref. No.

Part Number

013022

013022-02

013022-03

013086

013082

F400-0035

013193

013026

006737

F330-0075

000427

013026-04

F400-0034

F400-0022

013026-01

012780-14

011785

006596

011954

F330-0102

Description

Foot Pedal Weldment

Foot Pedal Bushing

Control Box Mount

TITAN400 Control Box

Clutch Lever Mounting Weldment

Ball Joint (Not Shown)

Platform Cover Plate

Boom Closure Plate

Handle

Titan Clutch Rod

Agitator Control Cable

Black Knob - 1-3/16 in. Dia.

Agitator Control Box

No. Required

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

CONTROL BOX WIRING (INTERNAL)

Switched Power

Battery Power

Remote Throttle Input Decrease Remote Throttle Input Increase

Clutch On

Clutch Of

Remote Radio PowerSwitch

12 1011

9 9 8 8 7 7 6 56 34 12

Power to Lower Controls

-12 GNDS

+12

FU3

FU2 FU1

BLK

WHT

YEL

CG2T

CG3T

RED

1112 10

56 34 12

WHT

BLACK/R

WHT

BLK

WHT

CG3T

-12 GNDS

+12

FU3 FU2 FU1

Jumper Wire #16 From

BLK

ORG

YEL

RED

BLU

BLK

WHT

CG2T

CG3T

CG6T

CG1T

DEUTSCH CONNECT

3 Conductor twisted CAN BUS

RED Batt Power

RED

BLK

GRE

WHT

CLUTCH AIR VA

GREEN

BROWN

RED/B

RED

Throttle Switch

Pump Switch

Murphy Powerview

Key Switch

RED

YEL

GREEN

GREY

BUS TO

BLUE

RED RED Main Power

N.C.

E-STOP

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

Part Number

012739

013218

013217

013074

013075

013076

020886

023892

052076

023076

055120

055123

055449

080526

366164

FW71555

FW71749-02

CONTROL BOX WIRING (INTERNAL)

Description

Terminal Block End Cover

Terminal Block w/ Fuse

Fuse Block Jumper

Key for Switch

No. Required

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

CONTROL BOX WIRING (EXTERNAL)

P/N 12970

V V

V V V V

Switched Power

Battery Power

Remote Throttle Input Decrease Remote Throttle Input Increase

Clutch On

Clutch Of

Remote Radio PowerSwitch

YEL

ORG

RED

BLK

BLUE

BLK

WHT

YEL

GRE

GREY

BUS TO

RED

GRE

WHT

YEL

BRN

ORG

RED

BLK

BLUE

ORG/B

RED/B

BLUE/B

16-9 190080

Drawing No. 12792

RED

GRE

WHT

ENCLOSURE Drawing # 13098

CLUTCH AIR VA

Female Pins for W

Switch Set @100 psi

5 8

3 16

BRN

BLK

ORG

YEL

BLUE

RED

WHT

BLK

WHT

RED

BLK

-12 DISENG

+12 DISENG

-12 ENG

+12 ENG

+12 VDC

N.O. PSI SW

WHT

BLK

Connector Engage

Connector Disengage

BLK

Female Pins for W

P/N 131

WHT

V V

WHT

BLK

Connector Disengage

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

85 (-)

86 (+)

RELAY BOX WIRING

Decrease Throttle Increase Throttle

Clutch Of

Clutch On

Switched Power

Battery Power

Clutch Of

Clutch On Remote Radio Power

Remote Throttle Input Decrease

Remote Throttle Input Increase

RADIO

REMOTE

1314 1112 10

9 78 56 34 12

CG5 CG3T

CG6

FLASHER

WHT FLASHER P/N 21

CG 3T

BLK

WHT

85 (-)

86 (+)

RED

ORANGE

TAN

PINK

BRN/BK

BROWN

ORG/BK

BLUE/BK

RED

GRE

WHT

GRE

BRN

BLK

RED

BLUE

RED

WHITE

BLACK

#14 awg

BLK

YEL/BK

RED

WHT

GRE

BLK

BLK/R

RED/BK

YELLOW

ORANGE

GREEN

RED

ORG/R

YEL/BLK

85 (-)

86 (+)

RED

BLACK

10 A

25A

10 A

RED

#12 awg

#14 awg

RED

YEL

CG 3T

GRE

CG 1

#14 awg

CG 3

CG 4

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

WHT

BLK

RED

GREEN

GRE

BLK

RED

GRE

RED

GRE

RED

WHT

RED

BLK

WHT

GRE

BROWN

WHT

RELAY BOX WIRING

80303 with REMOTE OPTION

V V

COOLER MOT

PUSH BUTT

WHT

BLK v v v v vv vv

GRAY

BLUE

* Use 170121 50 Pin Connector * Use 170122 Deutsch Socket * Use 170124 Deutsch Sealing Plug

V V

3 8

HH PP

If Hose Reel is not Used, Cap With Proper Dummy W

Sensor Loacted on radiator

V V

80303 170088

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

Part Number

010531

012825

013070

013218

013217

013074

013075

013099

013100

013103

021198

055449

080526

FW71749-02

RELAY BOX WIRING

Description

Flasher Mounting Bracket

DIN Rail End Bracket

Terminal Block End Cover

Terminal Block w/ Fuse

Relay Box Sub-Panel

Flasher

No. Required

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

B A D C G E F J

CG 1T

Key Switch

BLU 3

YEL

S

I

B

BLU

Not Used:

BLUE/BK & BRN

DO NOT CUT SHORT

GRN 3

BLK

ORG/BLK

ORG

Pump

Switch

Ref. No.

Part Number

GROUND LEVEL CONTROLS

Description

012792

052076

023076

FW71555

012759-02

080304

080526

012775

Ground Level Control Box

Key For Ignition Switch

Ground Level Control Box Decal

NOT ILLUSTRATED

Ground Level Controls Wiring

No. Required

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

(+) 12 VDC

HEAT SHRINK

Battery

P/N 170000

P/N 170014

P/N 13104 ATO In Line FuseHolder

Fuse 30 Amp

HEAT SHRINK

Alternator

6 Ga. RED 21"

6 Ga. BLK 21"

To Engine Ground Stud

6 Ga. BLK 21"

Engine Ground

ECU UNSWITCHED POWER

ECM

12 Ga. RED 94" PIN 4

12 Ga. BLACK 77" PIN 1

Starter

(-) 12 VDC

P/N 170000

Part Number

013104

052119

ENGINE WIRING HARNESS

Description

In-Line Fuse Holder

No. Required

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

BEARING & SEAL ASSEMBLY

AGITATOR AND SEAL ASSEMBLY

2“ AGITATOR SHAFT

THROUGH BACK SIDE

NOTE:

ITEM #1 (BEARING & SEAL ASSY)

INCLUDES ITEMS #2 - 9.

OUTSIDE

OF TANK

APPLY (1) SOLID, CONTINUOUS

BEAD OF SILICONE ADHESIVE

AROUND OUTER EDGE ON THE

INSIDE FACE OF THE CLAMPING

RING BEFORE INSTALLATION.

NOTE:

TO TIGHTEN, TURN THE NUT - NOT THE BOLT.

TORQUE TO 25 FT LBS. - DO NOT OVERTORQUE.

10 11

DRIVE END AGITATOR ASSEMBLIES

UPPER LEFT-HAND AGITATOR

(Optional)

LOWER LEFT-HAND AGITATOR

RIGHT-HAND AGITATOR

14 18

NOTE:

ITEM #12 (LEFT HAND

AGITATOR ASSEMBLY)

INCLUDES ITEMS #13 - 17.

NOTE:

ITEM #19 (RIGHT HAND

AGITATOR ASSEMBLY)

INCLUDES ITEMS #20 - 23.

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

AGITATOR AND SEAL ASSEMBLY

Part Number

012529

012527

012528

012525

012451

012450

012452

008154

012605

000Y08

012625

007705

022407

012520

012521

012956-16

012496-01

F330-0010-01

012501-02

012500-02

SE0064-03-02

F330-0010-02

012495-01

F330-0010-01

012501-01

012500-01

SE0064-03-01

F330-0010-02

013037

SE0181-03

SE0224-01

Ref. No.

Description

Bearing and Seal Assembly

Inner Clamping Ring w/Studs

Agitator Shaft Seal

Outer Clamping Ring

Flangette

2 in. Dia. Ball Bearing

Flangette w/Lube Coupling

Lube Coupling Adapter

Agitator Seal Washer

Agitator Hex Nut

2 in. Split Lock Collar

Grease Fitting

Grease Line Elbow

Bulk Head Fitting

Grease Line Hose - Lower Agitator

Grease Line Hose - Upper Agitator (Optional)

Idle Stub Shaft

Bolt-On Paddle

Left-Hand Agitator Section (TITAN280)

Left-Hand Agitator Section (TITAN330)

Left-Hand Agitator Assembly (TITAN400)

Bolt-On Paddle

Drive Stub Shaft

Bolt-On Paddle

Right-Hand Agitator Section (TITAN280)

Right-Hand Agitator Section (TITAN330)

Right-Hand Agitator Assembly (TITAN400)

Bolt-On Paddle w/Identification Hole

Third Agitator (TITAN280) (Optional)

Third Agitator (TITAN 330) (Optional)

Third Agitator (TITAN400) (Optional)

No. Required

2 per

1 per

2 per

1 per

2 per

1 per

4 per

2 per

1 per

2 per

1 per

2 per

1 Per

1 per

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

HYDRAULIC AGITATOR DRIVE

Optional Third Agitator

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

Ref. No.

Part Number

HYDRAULIC AGITATOR DRIVE

Description

012892

023295-006

012881

012881-S

F400-0008

012522-02

012522-04

012930

F400-0019

053023

012625

012496-01

013060

055698

SE0181-08

F330-0029

011780

010059

055103

190127-40

022407

008154

007705

012377

012522-02

012522-04

Seal Kit for 012892

Oil Shaft Seal

2 in. x 2 in. ID Steel 2 Piece Coupling

Splitcollar

Idle Stub Shaft

O-ring

Hydraulic Motor Mnt.

Agitator Coupling Guard

Coupling

Bushing w/ 1 in. Bore

Bushing w/ 2 in. Bore

Key

1/8M NPT X 18F NPT-90

Adapter Male to Female

Grease Fitting 1/8 in.

No. Required

Ref

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

HYDRAULIC SYSTEM

NOTE: ITEMS MARKED 1 THROUGH 35 ARE PART

OF HYDRAULIC HOSE AND FITTING KIT NUMBER

13199

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

Part Number

013136-04

013136-06

013136-08

013136-10

013136-11

013199-01

013199-02

013199-03

013199-04

013199-05

011927

012287

012881

012892

012894

013028

013048

013117

013119

013190

013139

013141

013049

013190

020052

053077

080329

160016

160042

008705

160068

160311

160586

160068

F400-0057

008708

011932

012044

012086

012087

012362

012516

013000

013114

013164

052401

053078

055234

055274

055309

055359

055757

FW65217

FW65219

FW71492

FW71784

FW71909

013136-01

013136-02

013136-03

Ref. No.

HYDRAULIC SYSTEM

Description No. Required

Lenz #A3405-12-16

Pressure Gauge #CF-5000-25

Lenz #A3105-8-10 (Midstate #6400-08-10)

Lenz #12 STP Plug

Lenz #A3355-4 45° Elbow

Lenz #12-16ARC (Midstate #6410-12-16)

Lenz #3105-32-32 (Air-Way #2404-32-32)

Lenz #A3105-20-20 (Midstate #6400-20-20)

Lenz #A3405-20-20 (Midstate #6801-20-20)

Lenz #A3405-12-20 (Midstate #6801-12-20)

Lenz #A3405-6-10 (Midstate #6801-6-10)

Lenz #3255SW-4-4 (Midstate #6506-4-4)

Lenz #A3105-4-6 (Midstate #6400-04-06)

Lenz #3755SW-6 (Midstate #6602-6-6-6)

Lenz #3505SW-4

2" Suction Hose x 42-1/2" OAL w /#32 FJIC BE

1-1/4" 100R4 Hyd. Hose x 34" OAL w/ #20 FJIC BE

1-1/4" 100R4 Hyd. Hose x 55" OAL w/ #20 FJIC x #20 FJIC90

3/4" 100R17 Hyd. Hose x 32" OAL w #12 FJIC BE

3/4" 100R17 Hyd. Hose x 111" OAL w/ #12 FJIC x #12 FJIC90

3/8" 100R17 Hyd. Hose x 92" OAL w/ #6 FJIC x #6 FJIC90

1/4" 100R17 Hyd. Hose x 37" OAL w/ #4 FJIC x #4 FJIC90

1/4" 100R17 Hyd. Hose x 41" OAL w/ #4 FJIC x #4 FJIC90

1/4" 100R17 Hyd. Hose x 110" OAL w/ #4 FJIC BE

1/4" 100R17 Hyd. Hose x 37" OAL w/ #4 FJIC x #4 FJIC90

1/2" 100R17 Hyd. Hose x 26" OAL w/ #8 FJIC x #12 FJIC

Suction Strainer

2" Ball Valve

Hydac Low Pressure Filter Assembly

Rexroth Hydraulic Pump

AKG DC16S-12-TC115 Heat Exchanger

Discharge Flange Pad

Suction Flange Pad

Clamp, Muffler - 2 1/2"

Hydac Filter Ass'y #02071996

Hydraulic Level Gauge

2" 90° Std. Elbow

2" Standard 45° Elbow

2" 90° Street Elbow

2" Stdandard Close Nipple

2" Std. Close Nipple x 7" Lg.

2" Std. Close Nipple x 12" Lg.

Hydraulic Pump Support

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

HYDRAULIC SYSTEM, THIRD AGITATOR

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

Ref. No.

HYDRAULIC SYSTEM, THIRD AGITATOR

Part Number Description

012086

055232

055274

FW71784

013162-01

013162-02

012945

055698

MSAE-MJIC 90º Elbow

1/4 in. Hyd. Hose x 55 in.

1/2 in. Hyd. Hose x 69 in.

Parker Hydraulic Valve

No. Required

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

HOSE REEL ASSEMBLY

12 13

NOTE:

ITEM #1 (HOSE REEL ASSEMBLY)

INCLUDES ITEMS #2 - 10.

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

Ref. No.

Part Number

008212

080302

008144

008200

008433

008313

008111B

008314

008635

008635-SK

008634

008199

003207

011894

F330-0077

F330-0094

F330-0104

F330-0017

052928

F330-0018

012781

012798

012860

HOSE REEL ASSEMBLY

Description

Hose Reel and Swivel Assembly

Hose Reel Gear

Hose Reel Chain - 69 in. Lg.

Pinlock w/Brackets Assembly

Idle Side Bearing

Drive Side Bearing

Seal Kit for 008635

Chain Sprocket - 11 Tooth

1-1/2 in. Dia. X 90 Degree Swivel Joint

Hose Roller and Spool Guide

Hose Reel Canopy

Hose Reel Canopy Support

Hose Reel Mount Cover

Upper Hose Reel Bracket

Lower Hose Reel Bracket

Hose Reel Lock Angle

Hose Reel Bearing Block

Hose Reel Pinlock Support Weldment

No. Required

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

LEFT SIDE

OF UNIT

22 3

DECALS

1 2

(Both Sides)

RIGHT SIDE

OF UNIT

(Both Sides)

(Inside of Railing -

Both Sides of Platform)

(Both

Sides)

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

Description

DECALS

Ref. No. Part Number

012817

005735

011567

012818

012886-02

012041-01

012278

031462

031463

012688

020970

012597

011569

012272

005216

012180

006869

007351

012820

023174**

011595**

012821

TITAN280/TITAN330/TITAN400 Decal Sheet

011793

011792

011791

011790

005188

005186

011690**

011662**

"Fall Hazard" Decal

"3,000 Gallon" Decal (TITAN330 Only)

"2,500 Gallon" Decal

"2,000 Gallon" Decal

"1,500 Gallon" Decal

"1,000 Gallon" Decal

"500 Gallon" Decal

"U.S. Patent No." Decal

012661-08**

012661-01** "TITAN330"

012661-02** "TITAN280"

012179

012687

"WARNING! Do Not Operate . . ." Decal

"CAUTION. Hydraulic System Instructions" Decal

007231-01

007230-01

012819

007231

"Service Weekly" Decal

"Service Daily" Decal

"BLEEDER VALVE - Open/Close" Decal

"Service Weekly" Decal

"RECIRCULATION VALVE - Close/Open" Decal

"VALVE - Open/Closed" Decal

"DANGER! Electrocution Hazard . . ." Decal

"CLUTCH - Engage/Disengage" Decal

"DANGER! Confined Space Hazard . . ." Decal

"HydroSeeder® Operating Instructions . . ." Decal

"DANGER! HOT EXHAUST!" Decal

"WARNING! Burn Hazard . . ." Decal

"WARNING Sever Hazard . . ." Decal

"CAUTION. Fall Hazard!" Decal

"CAUTION. Do Not Ride . . ." Decal

"IMPORTANT - This is a Tank Vent . . ." Decal

"CAUTION. Hose Reel Remote . . ." Decal

"HYDRAULIC FLUID ONLY" Decal

"DANGER! Do Not Use Remote . . ." Decal

"Tighten Suction Cover . . ." Decal

"Pressure Lubricator" Decal

"Hand Gun Only" Decal

023391*

NOT ILLUSTRATED

"DIESEL FUEL ONLY" Decal

NOTES:

This Decal is located on the fuel tank on the left side of the unit.

These Decals are not included on the 012820 Decal Sheet.

No. Required

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

Part Number

TOOL KIT

Description No. Required

410121-05

011775

021741

021375

012305

020365

012681A

006532

041371

012992

002427

160776

160313

013035

012993

001042

160309

002427

160774

012994

06604

002427

160772

012995

006605

002427

160772

012996

011861

002427

160775

012997

011860

002427

160775

000698

007469

Titan Tool Kit

Nozzle 2 1/2 in. Long Distance

12 in. Whip Hose W/1/8 in. Male Ends

Grease Gun (Hose Not Included)

Adhesive Label (Removal Aerosol Can)

Multi Puprose Grease

FINN Beige Aerosol Paint

Coupler Gasket 3 in.

3 in. Evertite Dust Cap-Brass

Titan Nozzle Adapter Assembly

Adapter 3 in. Male Brass

Reducer Bushing 3 in. x 2-1/2 in. Galvanized

Close Nipple 2-1/2 in. STD

Coupler Female 2-1/2 in.

Titan Long Distance Nozzle Assembly

Brass Nozzle 1-1/2 in. Long Distance

Close Nipple 1-1/2 in. STD Galvanized

Male Brass Adapter 3 in.

Reducer Bushing 3 in. x 1-1/2 in. Galvanized

Titan Wide Fan Nozzle Assembly

Veejet Brass Nozzle

Male Brass Adapter 3 in.

Reducer Bushing 3 in. x 1 in. Galvanized

Titan Narrow Fan Nozzle Assembly

Veejet Brass Nozzle

Male Brass Adapter 3 in.

Reducer Bushing 3 in. x 1 in. Galvanized

Titan Wide Fan Nozzle Assembly

Veejet Brass Nozzle

Male Brass Adapter 3 in.

Reducer Bushing 3 in. x 2 in. Galvanized

Titan Narrow Fan Nozzle Assembly

Veejet Brass Nozzle

Male Brass Adapter 3 in.

Reducer Bushing 3 in. x 2 in. Galvanized

Grease, 1 lb Tub

Lube Sticks, Box of 24

WHEN ORDERING PARTS, BE SURE TO STATE

SERIAL NUMBER OF MACHINE

LBTITAN280-TITAN330-TITAN400-MO

Part Number

013028

008705

013049

CU-LF3970

CU-FF5612

023910

023076

002439

006722

041368G

041371

005726

006532

012529

013043

012783

TITAN SPARE PARTS LIST

Description No. Required

Hydraulic Reservoir Cap

High Pressure Hydraulic Filter Element

Low Pressure Hydraulic Filter Element

Oil Filter

Fuel Filter

Ignition Key

3 in. Victaulic Pipe Gasket

1-1/4 in. Victaulic Pipe Gasket

6 in. Victaulic Pipe Gasket

Dust Cap 3 in. Main Tank Drain

Fuel Cap

3 in. Nozzle Coupler Gasket

2 in. Bearing Assemby

Swivel Kit

Clutch Assy 11 1/2 in.

WHEN ORDERING PARTS, BE SURE TO STATE

LBTITAN280-TITAN330-TITAN400-MO

SERIAL NUMBER OF MACHINE

Hi! I've reviewed the Finn TITAN 280 HydroSeeder parts and operator's manual. This document provides detailed information on this hydroseeding machine, including safety procedures, operating instructions, maintenance, parts lists, and diagrams. I'm ready to answer your questions.

Show related prompts

Assistant typing

Assistant terminated

Key features

Dual-agitation process
Slurry tank
Discharge assembly
Remote control
Hose reel
Second boom option
Air flush system

Frequently asked questions

The warranty period for the HydroSeeder® is two years or 2,000 hours, whichever comes first. All other equipment has a one-year or 1,200 hour warranty.

You must complete the Equipment Registration Form and mail it to FINN Corporation. If FINN Corporation does not have your completed registration form on file, your warranty claim will be denied.

1. Notify FINN Corporation of the failure of material or workmanship. 2. FINN will verify that they have your registration on file, that the warranty period is in effect, that the related part(s) are included in the scope of warranty, and then send you replacement part(s) and a warranty information packet. You must then follow all instructions as noted in the packet.