Dyna-Glo Delux KFA650DGD Use and Care Manual

Add to My manuals
24 Pages

advertisement

Dyna-Glo Delux KFA650DGD Use and Care Manual | Manualzz

INDOOR/OUTDOOR PRODUCTS

KEROSENE PORTABLE

FORCED AIR HEATERS

“USER’S MANUAL AND

OPERATING INSTRUCTIONS”

COMPLIES WITH

ANSI A10.10-1998

CAN/CSA/B140.0-03 AND CSA

B140.8-1967

MODEL : KFA650DGD

Before the first use of this heater, please read this USER’S MANUAL very carefully. This USER’S MANUAL has been designed to instruct you as to the proper manner in which to assemble, maintain, store, and most importantly, how to operate the heater in a safe and efficient manner.

Please keep this manual for future reference.

CONSUMER : Retain this manual for future reference.

Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 877-447-4768 8:30 a.m. - 4:30 pm CST, Monday - Friday.

or email us at [email protected]

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

DANGER:

IMPROPER USE OF THIS HEATER CAN RESULT IN SERIOUS INJURY OR DEATH

FROM BURNS, FIRE, EXPLOSION, ELECTRICAL SHOCK AND/OR CARBON

MONOXIDE POISONING.

WARNINGS:

1. RISK OF INDOOR AIR POLLUTION!

Use this heater only in well ventilated areas. Provide at least a three-square foot (2,800 sq. cm.) opening of fresh outside air for each 100,000 BTU/hr. of heater rating.

• People with breathing problems should consult a physician before using the heater.

• Carbon monoxide poisoning: Early signs of carbon monoxide poisoning resemble the flu, with headaches, dizziness and/or nausea. If you have these signs, the heater may not be working properly.

Get fresh air at once! Have the heater serviced. Some people are more affected by carbon monoxide than others.

These include pregnant women, persons with heart or lung disease or anemia, those under the influence of alcohol, or those at high altitudes.

• Never use this heater in living or sleeping areas.

2. RISK OFBURNS/FIRE/EXPLOSION!

NEVER use any fuel other than 1-K kerosene, #1 disel/fuel oil in this heater.

NEVER use fuel such as gasoline, benzene, paint thinners or other oil compounds in this heater.

(RISK OF FIRE OR EXPLOSION)

NEVER use this heater where flammable vapors may be present.

NEVER refill the heaters fuel tank while heater is operating or is still hot.

CAUTION :

Hot while in operation. Do not touch. Keep children, clothing and combustibles away from heater.

Minimum Clearances: Outlet: 8 feet (250cm) / Sides, top and rear: 4 feet (125cm)

NEVER block air inlet (rear) or air outlet (front) of heater.

NEVER use duct work in front or behind of heater.

NEVER move, handle, service a hot, operating or plugged in heater.

NEVER transport heater with fuel in it’s tank.

• When used with an optional thermostat or if equipped with a thermostat heater may start at any time.

ALWAYS locate heater on a stable and level surface.

ALWAYS keep children and animals away from heater.

• Bulk fuel storage should be a minimum of 25 ft. from heaters, torches, portable generators or other sources of ignition.

All fuel storage should be in accordance with federal, state or local authorities having jurisdiction.

3. RISK OF ELECTRIC SHOCK!

• Use only the electrical power (voltage and frequency) specified on the model plate of the heater.

• Use only a three-prong, grounded outlet and extension cord.

ALWAYS install the heater so that it is not directly exposed to water spray, rain, dripping water or wind.

ALWAYS unplug the heater when not in use.

1

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

CONTENTS OF USER’S MANUAL

ITEM

P R E C

8

.

7

.

.

5

6

3

4

.

.

.

.

1 .

2 .

9

10

11

12

13

14

15

N

K

O V

U E

L

M

R A

T E T

E

O R

REPLACING FUSE

T R

W I

S

E

P

I

F E

F

O P

A

T

O

A

P E

R

X P

A R

U

A T

N P

E R

E

N

I N

C

L O

T

I

I

T

A C

L I

G

O U

N

S

I

B

F I

O

V I

G

D

L

L

I

E

N G

T E

C

N

R O D U

U R E S

D

A

I

S

U

E R O S E N E

W

Y

E D

S T

T

C T

K I N G

A

I

O

E S H

I

-

( 1

O U

T I O N

R M S

S A

O N

A

G

O

F

N A N C

R

N

K

O O

N

P A R

F E T Y G U I

H

S

D

E

T I

A M

A

O R

R H E

S

N G

S

N O

E

.

M

A T E R

A T E R

1

D

G U I

T S D R A W I

D E

B

F

E

N

L Y

U

S

D E

I

G

E L

G N

O I L )

A G E O F Y O U R H E A T E R

PAGE #

16

17

18

19

8

9

14

15

5

6

4

5

3

2

1

2

1. INTRODUCTION

Please read this USER’S MANUAL carefully. It will show you how to assemble, maintain, and operate the heater safely and efficiently to obtain full benefits from its many built-in features.

2. FEATURES

Upper Shell

Front Handle

Hot Air Outlet

Shell Lower

Fan Guard

Fuel Gauge

Fuel Cap

Lamp

Thermostat Knob

Room Temp. Display

Operating Switch

Wheel

Power Cord

Fuel Drain Bolt

Figure 1.KFA650DGD MODEL

2

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

3. UNPACKING AND ASSEMBLY

1. REMOVE THE HEATER AND ALL PACKING MATERIALS FROM THE BOX. (See Fig.2)

NOTE: Save the shipping carton and packing materials for future storage.

Wheels

Cap Nuts Bushings Threaded Axle

Harware Kit

HW-KFA1020

Figure 2. PACKING MATERIALS

2. ASSEMBLING

Tools Required

Medium Phillips Screwdriver.

24 Socket Wrench.

Assembling wheel &handle

1. Slide threaded axle through the rear sectioon of the wheel support frame.

2. Slide one axle bushing on to each side of the axle. Slide one wheel on to each side of the axle.

Attach one cap nut on to each side of the threaded axle and tighten well.

3. Loosen 4 screws on the front handle in order to remove handle front.

4. Move the removed handle front to the handle on the front side as Figure 5 and then tighten 4 screws after matching handle and handle front.

CAUTION: DO NOT OPERATE heater without support frame assembled to tank.

3

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

Front Handle

Screw

Nut

Wheel

Cap Nut

Axle

Bushing

Figure 3. Assembling Handle & Wheel and Cord wrap

4. KEROSENE (1-K)

For optimal performance of this heater, it is strongly suggested that 1-K kerosene be used. 1-K kerosene has been refined to virtually eliminate contaminants, such as sulpher. Which can cause a rotten egg odor during the operation of the heater. However, #1 diesel/fuel oil may also be used if 1-K kerosene is not available.

Be advised that these fuels do not burn as clean as 1-K kerosene, and care should be taken to provide more fresh air ventilation to accomodate any added contaminants that may be added to the heated space.

KEROSENE SHOULD ONLY BE STORED IN A BLUE CONTAINER THAT IS CLEARLY

MARKED “KEROSENE”. NEVER STORE KEROSENE IN A RED CONTAINER.

Red containers are associated with gasoline.

NEVER store kerosene in the living space. Kerosene should be stored in a well ventilated place outside the living area.

NEVER use any fuel other than 1-K kerosene (#1 fuel oil is an acceptable substitute.)

NEVER use fuel such as gasoline, benzene, alcohol, white gas, camp stove fuel, paint thinners, or other oil compounds in this heater. These are volatile fuels that can cause an explosion or uncontrolled flames.

NEVER store kerosene in direct sunlight or near a source of heat.

NEVER use kerosene that has been stored from one season to the next. Kerosene deteriorates over time.

“OLD KEROSENE” WILL NOT BURN PROPERLY IN THIS HEATER.

4

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

5. OVERVIEW OF HEATERS DESIGN

Fuel System: This heater is equipped with a Fuel pump(Gear)that pulls fuel through the fuel line connected to the fuel tank and then pushes fuel through a filter and a solenoid valve and out the burner head nozzle.

This fuel is sprayed into the combustion chamber in a fine mist.

“Sure Fire Ignition”: The electronic ignitor sends voltage to a specially designed spark plug.

The spark plug ignites the fuel and air mixture.

The Air System: The heavy duty motor turns a fan that forces air into and around the combustion chamber. This air is heated and then forced out the front of the heater.

The Safety System:

A. Temperature Limit Control: This heater is equipped with a Temperature Limit Control designed to turn off the heater should the internal temperature rise to an unsafe level.

If this device activates and turns your heater off it may require service.

160˚F/71˚C 120˚F/49˚C

B. Electrical System Protection : This heaters electrical system is protected by a fuse mounted to the PCB assembly that protects it and other electrical components from damage.

If your heater fails to operate check this fuse first and replace as needed.

FUSE TYPE: 250 VAC / 8 amps

C. Flame-Out Sensor : Utilizes a photocell to monitor the flame in burn chamber during normal operation.

It will cause the heater to shut-off should the burner flame extinguish.

6. FUELING YOUR HEATER

NEVER FILL THE HEATER FUEL TANK IN THE LIVING SPACE: FILL THE TANK

OUTDOORS.

DO NOT OVERFILL YOUR HEATER AND BE SURE HEATER IS LEVELED.

IMPORTANT NOTICE REGARDING FIRST IGNITION OF HEATER:

The first time you light the heater, it should be done outdoors. This allows the oils, etc. used in manufacturing the heater to burn off outside.

WARNING!!: NEVER REFILL HEATER FUEL TANK WHEN HEATER IS OPERATING OR

STILL HOT.

5

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

7. OPERATION

A.) VENTILATION

RISK OF INDOOR AIR POLLUTION/USE HEATER ONLY IN WELL VENTILATED AREAS.

Provide at least a three-square foot(2,800 sq. cm.) opening of fresh outside air for each 100,000 BTU/Hr. of heater rating.

B.) OPERATION

TO START HEATER

1. Fill fuel tank with kerosene or No. 1 fuel oil.

2. Attach fuel cap.

3. Plug power cord of heater into three-prong, grounded extension cord.

Extension cord must be at least six feet long.

Extension Cord Wire Size Requirements

• 6 to 100 feet long, use 14 AWG conductor.

• 101 to 200 feet long, use 12 AWG conductor.

• 201 to 300 feet long, use 10 AWG conductor.

• 301 to 400 feet long, use 8 AWG conductor.

• 401 to 500 feet long, use 6 AWG conductor.

4. Turn “Thermostat Control Knob” to desired setting(setting range : 40℉~110℉) and push operating switch to “ON” position, power indicator lamp and room temp. display will light and heater will start.

NOTE: Room Temp. display indicates as following,

• When room temp. is less than 0℉ : “Lo”

• When room temp. is between 0℉and 99℉ : Indicates in figure.

• When room temp. is more than 99℉ : “Hi”

If heater does not start, the thermostat setting may be too low, turn “THERMOSTATCONTROL

Knob” to higher position to start heater. If heater still does not start, turn operating switch to “OFF” and then to “ON” position. (Figure 4). If heater still does not start, see Troubleshooting Guide on page 13.

INDICATOR LAMP

ROOM TEMP. DISPLAY

THERMOSTAT CONTROL KNOB

Figure 4. CONTROL PARTS

OPERATING SWITCH

NOTICE : The major electrical components of this heater are protected by a safety fuse mounted to the PCB board.

If your heater fails to start, check this fuse first and replace as necessary. You should also check your power source to insure that proper voltage and frequency are being supplied to the heater.

6

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

TO STOP HEATER

CAUTION ; Never unplug heater while heater is running

Heater must go through cooling cycle. The cooling cycle cools the combustion chamber. Damage to heater can occur if combustion chamber is not cooled. Do not restart heater until cooling cycle is complete.

1. Turn operating switch to “OFF”.

This will cause heater flame to go out.

The motor will continue to run during the cooling cycle.

(Room Temp. Display will show “CC” during the cooling cycle)

This allows the fan to cool the combustion chamber. When the cooling cycle

(approx.1Min) is finished, the motor will stop.

Do not unplug heater until cooling cycle is finished.

2. Unplug power cord.

3. To temporarily stop heaters, set thermostat at a temperature lower than air around heater,

Heater will cycle back on if air temperature around heater matches thermostat setting.

TO RESTART HEATER

CAUTION ; Do not restart heater until cooling cycle is finished.

The cooling cycle cools the combustion chamber.

1. Wait until cooling cycle is finished after stopping heater.

2. Repeat steps under to start HEATER.

7

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

8. LONG TERM STORAGE OF YOUR HEATERT

1. Remove fuel drain bolt from rear bottom side of fuel tank using 3/4” socket or adjustable wrench and drain.

2. Using a small amount of kerosene, swirl and rinse the inside of the tank.

NEVER mix water with the kerosene as it will cause rust inside the tank.

Pour the kerosene out making sure that you remove it all.

IMPORTANT : Do not store kerosene over summer months for use during next heating season.

Using old fuel could damage heater.

3. Reinstall Fuel Drain Bolt to Fuel tank and tighten firmly using 3/4” socket or adjustable wrench.

Seal

Fuel Drain Bolt

Figure 5. Drain Bolt

IMPORTANT : Before reinstalling the fuel drain bolt, make sure the seal is on the bolt. If the seal is not used the bolt cannot be installed correctly and the fuel tank will leak.

4. Store heater in dry well ventilated area. Make sure storage place is free of dust and corrosive fumes.

5. Store the heater in the original box with the original packing material and keep the USER’S MANUAL with the heater.

8

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

9. MAINTENANCE

WARNING!! NEVER SERVICE HEATER WHILE IT IS PLUGGED IN

OR WHILE HOT!

USE ORIGINAL EQUIPMENT REPLACEMENT PARTS. Use of third party or other alternate components will void warranty and may cause unsafe operating conditions.

A.) UPPER SHELL REMOVAL

-Remove screws along each side and top of

heater using medium phillips screw driver.

-Lift upper shell off.

(See Figure 6)

Figure 6. Upper Shell Removal

B.) FAN BLADES AND AIR DEFLECTOR

CLEAN EVERY SEASON OR AS NEEDED.

- Remove upper shell (See figure 6 above)

- Clean fan blades and air deflectors using a soft cloth

moistened with kerosene or solvent.

- Dry fan blades and air deflectors thoroughly.

- Reinstall upper shell.

AIR DEFLECTOR

FAN BLADE

Figure 7. Fan Blades and Air Deflectors

9

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

C.) SPARK PLUG

CLEAN AND REGAP EVERY 600 HOURS

OPERATION OR REPLACE AS NEEDED.

- Remove upper shell (See page 9).

- Remove spark plug wire from spark plug

(See Figure 8)

- Remove spark plug from burner head using

medium phillips screw driver.

- Clean and regap spark plug electrodes to

0.14”(3.5mm)gap.

- Reinstall spark plug in burner head.

- Attach spark plug wire to spark plug.

- Reinstall upper shell.

BURNER HEAD

SPARK PLUG

SPARK PLUG WIRE

D.) NOZZLE

REMOVE DIRT IN NOZZLE AS NEED (See page 14)

- Remove upper shell (See page 9).

- Remove fuel line from solenoid valve using

1/4” wrench.

- Remove spark plug wire from spark plug.

- Remove spark plug from burner head using medium

phillips screw driver.

- Remove five screws using medium phillips screwdriver

and remove burner head from

combustion chamber.

- Carefully remove nozzle from burner head

using 5/8” socket wrench.

- Blow compressed air through face of

nozzle.

(this will remove any dir in nozzle)

- Inspect nozzle for damage. If damaged

or clogged, replace nozzle.

- Make sure plug is in place on burner

head.

- Reinstall nozzle into burned head and

tighten firmly. (175~200 inch-pounds)

- Reinstall spark plug in burner head.

- Attach burner head to combustion

chamber.

- Attach spark plug wire to spark plug.

- Attach fuel line to solenoid valve

tighten firmly.

- Replace upper shell.

NOZZLE

NOZZLE FOACE

PLUG

Figure 8. Spark Plug

BURNER HEAD

SPARK PLUG

SOLENOIO VALUE

FUEL LINE

Figure 9. NOZZLE

SPARK PLUG WIRE

10

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

E.) PHOTOCELL

CLEAN PHOTO CELL ANNUALLY OR AS NEEDED.

- Remove upper shell(See Page 9)

- Remove photocell from photocell Bracket and disconnect photocell from connector.

- Clean photocell lens with cotton swab.

- Inspect photcell lens for damage. If damaged, replace photocell.

PHOTOCELL BRACKET

PHOTOCELL

CONNECTOR

PHOTOCELL LENS INSTALL PHOTOCELL

1)INCORRECT

2)CORRECT

Figure 10. Clean photocell Lens

F.) FUEL LINES

TIGHTENING FUEL LINES ANNUALLY OR AS NEEDED.

- Remove upper shell (See page 9).

- Remove fan guard (See Figure 11)

- Use 1/4” wrench and tighten fuel lines(A) at solenoid valve and at pump. (See Figure 12)

- Use 3/8” wrench and tighten fuel lines (B) at pump, pump fuel filter assembly.

- Reinstall fan guard.

SOLENOID VALVE

FAN GUARD

PUMP

F i g u r e 1 1 .

R e m o v e F a n g u a r d

11

FUEL LINE(A) FUEL LINE(B)

F i g u r e 1 2 .

T i g h t e n f u e l il n e

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

G.) FUEL FILTER

CLEAN TWICE PER HEATING SEASON OR AS NEEDED.

Tank Fuel Filter

- Remove fan guard.(See page 11).

- Disconnect fuel line (B) from pump and pump

fuel filter assembly with 3/8” wrench (See

Figure 13)

- Remove two screws that fix bracket-filter to shell

lower and remove bracket-filter.

- Carefully pry fuel filter loose from fuel tank

withflat end of screw driver.

- Wash fuel filter and fuel lines with clean

kerosene.

- Replace fuel filter into fuel tank.

- Connect fuel lines (B) to pump and pump fuel

filter assembly.- Reinstall fan guard.

- Replace bracket-filter to shell lower.

- Carefully pry fuel filter loose from fueltank with

flat end of screw driver.

- Wash fuel lines and fuel filter withclean

kerosene.

PUMP

SHELL LOWER

FUEL LINE(B)

SCREW

BRACKET-FILTER

PUMP FUEL FILTER ASSEMBLY

FUEL FILTER

Figure 13. Remove Tank Fuel Filter

Pump Fuel Filter

- Remove fan guard.(See page 11)

- Unscrew (C.W) filter bottom from

filter top with adjustble pliers.

- Remove fuel filter, gasket, magnet

from filter

bottom.(See Figure 14)

- Wash filter bottom with clean

kerosene.

- Wipe inside of filter bottom dry with

clean cloth.

- Wash Fuel filter in clean kerosene.

- Remove dirt attached magnet.

- Put clean magnet, fuel filter and gasket

back in filter bottom.

- Tighten firmly.

FILTER TOP

GASKET

FUEL FILTER

MAGNET

FILTER BOTTOM

Figure 14. Fuel Pump Filter

12

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

H.) PUMP PRESSURE ADJUSTIMENT

- Remove pressure gauge plug from pump with 1/8” allen wrench.

- Install accessory pressure gauge to pressure gauge port. (See Figure 15)

- Start heater (See operation, page 6)

Allow motor to reach full speed.

- Adjust pressure. (Using a small flat blade screw driver)

Turn pressure adj. Screw to clock wise to increase pressure.

Turn screw to counter clock wise to decrease pressure.

Set pump pressure to 110 PSI.

- Stop heater (See operation, page 6)

- Remove pressure gauge. Replace pressure gauge plug in pressure gauge port.

PRESSURE GAUGE PORT

PRESSURE GAUGE PLUG

PRESSURE ADJ.SCREW

PRESSURE GAUGE

PUMP

Figure 15. Adjusting Pump Pressure

NOTE:

USE ONLY ORIGINAL EQUIPMENT REPLACEMENT PARTS.

USE OF ALTERNATE OR THIRD PARTY COMPONENTS WILL VOID ANY WARRANTY

AND MAY CAUSE UNSAFE OPERATING CONDITION.

13

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

10. REPLACING FUSE

NOTICE : This heater is fuse protected.

If your heater fails to ignite, DO NOT RETURN YOUR HEATER TO THE

STORE.

Please follow the simple instruction below to inspect and change the fuse.

PROCEDURE FOR REPLACING FUSE

WARNING : SHOCK HAZARD

To prevent personal injury, unplug the power cord before replacing fuse.

1. Unplug heater.

2. Turn Fuse Cover COUNTERCLOCKWISE 45° using a flat blade screwdriver and remove Fuse from

Fuse Holder.

3. Replace Fuse with enclosed fuse.

WARNING : FIRE HAZARD

To avoid fire, Do not substitute with a higher or lower current rating.

4. Turn Fuse Cover CLOCKWISE 45° using a flat blade screwdriver while slightly pushing.

NOTE : Specified fuse rating : 250VAC/20A

Fuse

Fuse Cover

Fuse Holder

Figure 16. Replacing Fuse

14

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

11

. TROUBLE SHOOTING GUIDE

TROUBLE POSSIBLE CAUSE

1. Wrong pump pressure

2. Dirty Fuel Filter

(Indicator lamp is flickering and room temp. display indicates “E1”) properly installed. (Not

6. Bad electrical connection between photocell and MAIN

P C B a s s e

7. Defective photocell

CORRECTIVE ACTION

1. See Pump Pressure Adjustment, page 13.

S e e w i ir n g d ai g r a m , p a g e

7. Replace photocell, page 11.

.

and allow to cool (about 10 min.).

“ON” position.

motor runs for a short period of time. (Indicator lamp is flickering and room temp. display indicates “E1”)

5. Dirt in nozzle

6. Water in fuel tank

7. Bad electrical connection between ignitor and MAIN s

PCB assembly p a r k p l

9. Defective ignitor

(not opening) is plugged in and operating switch

(Indicator lamp is on or flickering)

(Indicator lamp is flickering and room temp. display indicates “E2”)

1. Room Temp. sensor d si c o n n e c d

1. Thermostat switch failure

Heater will not turn-on

(Indicator lamp is off)

1. No electrical power

2. Blown fuse

8 .

A t at c h i g n ti o r w ri e t o s p

See Spark Plug, page 10.

a r k p l u g

9. Replace ignitor.

10.Check electrical connections and voltage to solenoid valve. If defective, replace solenoid valve.

.

S e e W i ir n g D ai g r a m , p a g e 1 5 .

1. Reconnect sensor

S e e w i n g d ai g r a m , p a g e 1 5

See wiring diagram, page 15.

.

extension cord are plugged in.

Check power supply.

15

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

12

. WIRING DIAGRAM

CONTROL PCB

BLACK CN7

BLACK

BLACK

LIMIT

CONTROL

SOL.

VALVE

WHITE

POWER LAMP

(LED)

THERMOSTAT

(TEMP. CONTROL)

CN5

WHITE

PHOTOCELL

POWER

PLUG

CN8

YEL

BLACK

BROWN

BLACK SPARK PLUG

BROWN

RED

CN4

CN3

BROWN IGNITOR

BLACK

ORANGE

RED

PUMP

MOTOR

BLACK

WHITE

CAPACITOR

CN2(AC2)/

CN1(AC1)/

BLUE

CN6

WHT

BLK

YEL

OPERATING SWITCH

BLUE

ROOM SENSOR

GREEN

EARTH

FUSE

20A/250VAC

16

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

13

. SPECIFICATIONS

6 9 2.

(" 1 7 5 8 m m )

KFA650DGD

3 2 8.

(" 8 3 4 m m )

M O D E L

B T U / H r

Fuel Consumption-Gal./ ( ./Hr)

Fuel Tank Capacity-Gal ( )

Pump Pressure PSI (kgf/ )

V o

P h a s tl e

/s H /z A m p s

Size(W D H), Inch( )

Weight Ibs. ( )

KFA650DGD

6 5 0 , 0 0 0

4.9(18.55)

29.0(110.0)

110(7.73)

1 2 0 V A C /

1

6 0 / 7 .

1

32.8” 69.2

48.7 (834 1758 1237)

2 7 5 .

6 ( 1 2 5 )

17

6

35

36

37

38

39

40

41

23

13

4

7

1

5

24

24

4

14

15

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

14

. EXPLODED PARTS DRAWING (KFA650DGD MODEL)

NOTE: SPECIFY MODEL NUMBER AND PART NUMBER WHEN ORDERING PARTS.

4

47

25

10

4

16

31

18

17

18 28

30

29

30

26

4

17

27

4

21

22

20

4

4

33 24

43

32

4

45

42

19

46

34

44

8

15

9 17

4

3

11

2

12

18

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

15

. PARTS LIST

KEY No.

29

30

31

32

25

26

27

28

21

22

23

24

17

18

19

20

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

45

46

47

41

42

43

44

37

38

39

40

33

34

35

36

DESCRIPTION

Fuel Tank Assembly

Fuel Drain Bolt

Bracket-Cord

Flange Screw

Fuel Gauge

Fuel Filter

Fuel Cap

Filler Neck Assembly

Space Support

Card Support

Cord Bushing

Power Cord

Shell Lower

Bracket-Pipe

Bolt-HH

Lock Nut

Bushing Grommet(L)

Bushing Grommet(S)

Line - Fuel

Harness-Burner

Wire Clip

Thermistor

Cone-Ouside

Clip Nut

Chamber Assembly

Air Deflector

Burner Head Assembly

Bracket Photocell

Screw BH1

Photocell

Temperature Limit

Igniter

Cover Igniter

Motor & Pump Assembly

P.C.B Assembly

Cover Display

Rating Plate

Window Display

Operating Switch

Fuse Holder

Fuse

Guide Shell

Bracket-Filter

Fan Assembly

Bolt Standard Socket

Guard Fan

Shell Upper

PART No.

KFA650DGD

2151-0021-01

4329-0072-00

3131-0357-01

4319-0015-00

2156-0054-00

3221-0009-00

2151-0022-00

2155-0011-00

3713-0004-00

3713-0016-00

3712-0013-00

3980-0228-00

3111-0252-04

3131-0363-01

4321-0182-00

4331-0022-00

3231-0121-00

3231-0120-00

3740-0058-00

39D0-0785-00

3715-0014-00

38C0-0054-00

2153-0016-01

3131-0182-00

2152-0083-00

3131-0361-00

2152-0084-00

3131-0159-00

4311-0068-00

2153-0017-00

38C0-0151-00

39E0-0029-00

3131-0309-01

2154-0046-00

215A-0057-00

3121-0376-01

3221-0072-08

3231-0113-00

39A0-0209-00

3930-0012-00

3920-0061-00

3121-0378-01

3131-0464-00

2154-0047-00

4323-0005-00

3561-0064-01

3111-0253-04

FOR TECHNICAL ASSISTANCE SEE YOUR LOCAL RETAILER OR

CONTACT US AT:

Phone : 1-877-447-4768

19

Quantity

1

1

2

1

1

1

1

4

1

1

1

14

1

1

6

1

4

4

1

2

1

1

5

3

1

1

1

1

1

1

2

43

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

15

. PARTS LIST (BURNER HEAD ASSEMBLY & MOTOR AND PUMP ASSEMBLY)

NOTE: SPECIFY MODEL NUMBER AND PART NUMBER WHEN DRDERING PARTS.

KEY NO. DESCRIPTION

1

8

9

6

7

10

4

5

2

3

Burner Head

Plug

Nozzle

Spark Plug

Fiber Washer

Spring Washer

Flange Bolt

Nipple-Straight

Solenoid Valve

Elbow Male

PART NO.

3531-0012-00

3541-0060-00

SP-KFA1028

SP-KFA1009

4349-0017-00

4342-0009-00

4329-0013-00

3541-0057-00

39A0-0084-00

3740-0037-00

1

1

1

1

QTY.

1

1

1

1

1

1

Figure 17. Burner Head Assembly

10

11

12

13

8

9

6

7

14

15

16

KEY NO. DESCRIPTION

1

4

5

2

3

Motor

Supportor-Motor

Bolt(HH)

Nut Lock

Coupling-Pump

Gear Pump

Bolt-Headless Socket

Filter Oil Assembly

Elbow Male

Fitting-Straight

Holder Condensor

Bushing Grommet(S)

Cover Condensor

Screw(TH2S)

Flange Screw

Capacitor

PART NO.

3970-0111-00

3121-0375-00

4321-0182-00

4331-0022-00

3531-0013-00

3740-0060-00

4323-0004-00

3740-0034-00

3740-0044-00

3740-0039-00

3131-0295-00

3712-0120-00

3121-0338-00

4312-0046-00

4319-0015-00

3820-0146-00

1

1

1

1

1

1

1

2

1

3

1

1

4

QTY.

1

4

1

Figure 18. Motor and Pump Assembly

20

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

15

. PARTS LIST (Wheel and Handle)

NOTE: SPECIFY MODEL NUMBER AND PART NUMBER WHEN ORDERING PARTS.

KEY No.

5

6

7

7-1

7-2

3

4

1

2

DESCRIPTION

Wheel Support Frame

Handle Frame

Frame Supportor

Front Handle

Wheel

Threaded Axle

Hardware Kit

Bushing

Cap Nut

PART No.

3551-0041-00

3551-0043-00

3551-0044-00

3551-0042-00

3720-0004-00

3541-0094-00

HW-KFA1020

INCLUDED IN HARDWARE KIT

INCLUDED IN HARDWARE KIT

Quantity

1

2

2

1

2

2

1

1

2

4 3

2

1

5

7-2

6

7-1

21

advertisement

Related manuals

advertisement