Graco 308159C Stubby Size 4:1 Ratio President Pump Owner's Manual

INSTRUCTIONS-PARTS LIST
308–159
Rev. C
Supersedes A
and PCN B
This manual contains important
warnings and information.
READ AND KEEP FOR REFERENCE.
INSTRUCTIONS
STUBBY SIZE
4:1 Ratio President Pump
400 psi (28 bar) Maximum Fluid Working Pressure
100 psi (7 bar) Maximum Air Input Pressure
Part No. 224–757, Series C
Carbon Steel, Leather Packed Pump
For Use in Lubrication Systems
Table of Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Mounting Hole Layout . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Graco Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Toll-Free Graco Phone Number . . . . . . . . . . . . . . . . . 16
GRACO INC.
P.O. BOX 1441 MINNEAPOLIS, MN
COPYRIGHT 1992, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
55440–1441
Symbols
Warning Symbol
Caution Symbol
CAUTION
WARNING
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.
WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.
INSTRUCTIONS
D This equipment is for professional use only.
D Read all instruction manuals, tags, and labels before operating the equipment.
D Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor.
D Do not alter or modify this equipment.
D Check equipment daily. Repair or replace worn or damaged parts immediately.
D Do not exceed the maximum working pressure of the lowest rated system component. Refer to the
Technical Data on page 15 for the maximum working pressure of this equipment.
D Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Technical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.
D Do not use 1,1,1–trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or
fluids containing such solvents in aluminum equipment. Such use could result in a serious chemical
reaction, with the possibility of explosion.
D Do not use hoses to pull equipment.
D Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 82_C (180_F) or below –40_C (–40_F).
D Wear hearing protection when operating this equipment.
D Do not lift pressurized equipment.
D Comply with all applicable local, state, and national fire, electrical, and safety regulations.
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury.
Ground the equipment and the object being lubricated. Refer to Grounding on page 5.
If there is any static sparking or you feel an electric shock while using this equipment, stop dispensing immediately. Do not use the equipment until you identify and correct the problem.
Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being dispensed.
Keep the dispense area free of debris, including solvent, rags, and gasoline.
Electrically disconnect all equipment in the dispense area.
Extinguish all open flames or pilot lights in the dispense area.
Do not smoke in the dispense area.
Do not turn on or off any light switch in the dispense area while operating or if fumes are present.
Do not operate a gasoline engine in the dispense area.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
Know the specific hazards of the fluid you are using.
Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.
MOVING PARTS HAZARD
Moving parts, such as the air motor piston, can pinch or amputate your fingers.
Keep clear of all moving parts when starting or operating the pump.
Before servicing the equipment, follow the Pressure Relief Procedure on page 8 to prevent the
equipment from starting unexpectedly.
Notes
4
308-159
Installation
General Information
Z
X
W
NOTE: Reference numbers and letters in parentheses
in the text refer to the callouts in the figures and the
parts drawing.
NOTE: Always use Genuine Graco Parts and Accessories, available from your Graco distributor. If you
supply your own accessories, be sure they are adequately sized and pressure rated for your system.
Y
0864
Fig. 1
2. Air and fluid hoses: use only electrically conductive
hoses.
Fig. 2 is only a guide for selecting and installing system components and accessories. Contact your Graco
distributor for assistance in designing a system to suit
your particular needs.
3. Air compressor: follow manufacturer’s recommendations.
Prepare the Operator
4. Dispensing valve: ground through connection to a
properly grounded fluid hose and pump.
All persons who operate the equipment must be
trained in the safe, efficient operation of all system
components as well as the proper handling of all fluids.
All operators must thoroughly read all instruction
manuals, tags, and labels before operating the equipment.
Grounding
WARNING
FIRE AND EXPLOSION HAZARD
Before operating the pump, ground the
system as explained below. Also read
the section FIRE AND EXPLOSION
HAZARD on page 3.
1. Pump: order Part No. 237–569 Ground Wire and
Clamp. See Fig. 1. Loosen the grounding lug
locknut (W) and washer (X). Insert one end of the
ground wire (Y) into the slot in lug (Z) and tighten
the locknut securely. Connect the other end of the
wire to a true earth ground.
5. Fluid supply container: follow your local code.
6. Object being lubricated: follow your local code.
7. Solvent pails used when flushing: follow your local
code. Use only metal pails, which are conductive,
placed on a grounded surface. Do not place the
pail on a nonconductive surface, such as paper or
cardboard, which interrupts the grounding continuity.
8. To maintain grounding continuity when flushing or
relieving pressure, hold a metal part of the dispensing valve firmly to the side of a grounded
metal pail, then trigger the valve.
Mounting the Pump
Mount the pump to suit the type of installation planned.
The pump dimensions and mounting hole layout are
shown on page 14.
If the pump is immersed, be sure the pump intake is
1/2 in. (13 mm) off the bottom of the fluid container.
If the pump is mounted on the wall or on a stand,
connect a suction line to the pump’s 1–1/2” npt(f) fluid
inlet and place the other end of the line in the fluid
container.
Installation
F
G
MAIN AIR LINE
Y
E
B
KEY
A
B
C
D
E
F
G
H
J
Y
1
Pump
Pump Runaway Valve
Air Line Lubricator
Bleed-Type Master Air Valve
(required, for pump)
Air Regulator
Air Line Filter
Bleed-Type Master Air Valve
(for accessories)
Fluid Drain Valve (required)
Suction Kit
Ground Wire (required; see page
5 for installation instructions)
D
C
A
FLUID SUPPLY LINE
J
1
H
Fluid outlet is actually on the
back side of the pump.
06113
Fig. 2
6
308-159
Installation
Available Accessories (must be
purchased separately)
A pump runaway valve (B) automatically shuts off
the pump if it starts running too fast. A pump which
runs too fast can be seriously damaged.
Air Line Accessories
WARNING
A bleed-type master air valve (D) is required in
your system to help reduce the risk of serious
injury, including splashing of fluid in the eyes or on
the skin, and injury from moving parts if you are
adjusting or repairing the pump.
The bleed-type master air valve relieves air trapped
between this valve and the pump after the air is
shut off. Trapped air can cause the pump to cycle
unexpectedly. Locate the valve close to the pump.
The bleed-type master air valve (D) is required in
your system to relieve air trapped between it and
the air motor when the valve is closed (see the
WARNING above). Be sure the bleed valve is
easily accessible from the pump, and is located
downstream from the air regulator (E). Order Part
No. 113–269 Bleed Valve.
An air line lubricator (C) provides automatic air
motor lubrication. Install downstream from the
pump air regulator (E).
Install a second air bleed valve (G) upstream
from all other air line accessories, to isolate the
accessories for servicing.
Fluid Line Accessories
WARNING
A fluid drain valve (H) is required in your system to
help reduce the risk of serious injury, including
splashing of fluid in the eyes or on the skin.
The fluid drain valve assists in relieving fluid pressure in the displacement pump, hose, and dispense valve. Triggering the valve to relieve pressure may not be sufficient.
The air regulator (E) controls pump speed and
outlet pressure by adjusting the air pressure to the
pump. Locate the pump air regulator upstream
from the pump’s bleed-type master air valve (D).
The fluid drain valve (H) is required in your system to relieve fluid pressure in the hose and dispense valve (see the WARNING above).
The air filter (F) removes harmful dirt and moisture
from the compressed air supply.
Connect a suction tube kit (J) to the pump’s
1–1/2” npt(f) fluid inlet.
308-159
7
Operation
Pressure Relief Procedure
WARNING
PRESSURIZED EQUIPMENT HAZARD
The system pressure must be manually relieved to
prevent the system from starting or dispensing
accidentally. To reduce the risk of an injury from
accidental spray from the dispense valve, splashing fluid, or moving parts, follow the Pressure
Relief Procedure whenever you:
are instructed to relieve the pressure,
stop dispensing,
check or service any of the system equipment,
or install or clean the nozzle.
If the pump is not immersed, fill the packing nut/wetcup 1/2 full with a compatible solvent. Keep the cup
filled at all times to help prevent the fluid you are
pumping from drying on the exposed displacement rod
and damaging the throat packings.
Flush the Pump Before First Use
The pump is tested with lightweight oil, which is left in
to protect the pump parts. If the fluid you are using
may be contaminated by the oil, flush it out with a
compatible solvent. See Flushing on page 10.
1
Torque to 20–24 ft-lb (27–33 N.m).
1. Shut off the air supply to the pump.
2. Close the bleed-type master air valve (D, required
in your system).
3. Hold a metal part of the dispensing valve (if used)
firmly to the side of a grounded metal pail, and
trigger the valve to relieve pressure.
4. Open the drain valve (H, required in your system),
having a container ready to catch the drainage.
5. Leave the drain valve open until you are ready to
spray again.
If you suspect that the spray nozzle or hose is completely clogged, or that pressure has not been fully
relieved after following the steps above, very slowly
loosen the hose end coupling and relieve pressure
gradually, then loosen completely. Now clear the
nozzle or hose.
1
U
Packing Nut
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure above.
Check the tightness of the packing nut/wet-cup (U)
periodically. The nut should be tight enough to prevent
leakage. Torque the nut to 20–24 ft-lb (27–33 N.m); do
not overtighten or you may damage the packings.
Relieve pressure before adjusting the nut. See Fig. 3.
Fig. 3
Operation
Prime the Pump
1. See Fig. 2. Close all bleed-type air valves (D, G).
10. Relieve the pressure. Install the nozzle in the
dispense valve, as explained in the dispense valve
manual.
2. Close the pump air regulator (E).
3. Close the fluid drain valve (H).
4. Check that all fittings throughout the system are
tightened securely.
5. Connect the air supply line to the pump air inlet.
6. Open the bleed-type air valves (D, G).
7. Hold a metal part of the dispense valve (if used)
firmly to the side of a grounded metal pail and hold
the trigger open.
8. Open the air regulator (E) until the pump starts.
Run the pump slowly until all air is pushed out and
the system is fully primed. Always use the lowest
pressure necessary to get the desired results.
Higher pressures cause premature pump wear.
9. Release the dispense valve trigger and lock the
trigger safety.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
WARNING
COMPONENT RUPTURE HAZARD
To reduce the risk of overpressurizing
your system, which could cause component rupture and serious injury, never
exceed 100 psi (7 bar) air supply pressure to the
pump.
11. Use the air regulator (E) to control pump outlet
pressure and pump speed. Always use the lowest
pressure necessary to get the desired results.
Higher pressure causes premature pump wear.
CAUTION
Do not allow the pump to run dry. It will quickly
accelerate to a high speed, causing damage. If your
pump is running too fast, stop it immediately and
check the fluid supply. If the container is empty and
air has been pumped into the lines, refill the container and prime the pump and the lines, or flush and
leave it filled with a compatible solvent. Eliminate all
air from the fluid system.
Maintenance
Shutdown and Care of the Pump
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
For overnight shutdown, stop the pump at the bottom
of its stroke to prevent fluid from drying on the exposed displacement rod and damaging the throat
packings. Relieve the pressure.
CAUTION
Never leave water or water-base fluid in the pump
overnight. If you are pumping water-base fluid, flush
with water first, then with a rust inhibitor such as
mineral spirits. Relieve the pressure, but leave the
rust inhibitor in the pump to protect the parts from
corrosion.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
Always flush the pump before the fluid dries on the
displacement rod. See Flushing below.
1. Relieve the pressure.
Flushing
2. Hold a metal part of the dispense valve firmly to
the side of a grounded metal pail.
WARNING
FIRE AND EXPLOSION HAZARD
Before flushing, read the section FIRE
AND EXPLOSION HAZARD on page
3. Be sure the entire system and flushing pails are properly grounded. Refer to
Grounding on page 5.
Flush the pump:
Before the first use
When changing fluids
3. Start the pump. Always use the lowest possible
fluid pressure when flushing.
4. Trigger the dispense valve.
5. Flush the system until clear solvent flows from the
dispense valve.
6. Relieve the pressure.
Corrosion Protection for Carbon Steel
Pumps
CAUTION
Water, or even moist air, can cause your pump to
corrode. To help prevent corrosion, never leave the
pump filled with water or air. Follow the instructions
under Flushing, at left.
Before storing the pump.
Fluid Piston and Intake Valve Adjustment
Flush with a fluid that is compatible with the fluid you
are pumping and with the wetted parts in your system.
Check with your fluid manufacturer or supplier for
recommended flushing fluids and flushing frequency.
The fluid piston and intake valves are factory set for
pumping medium viscosity fluids. See the separate
displacement pump manual, 307–983, for adjustment
procedures to pump lighter or heavier viscosity fluids.
Troubleshooting
1. Relieve the pressure.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
Problem
Pump fails to operate.
2. Check all possible problems and solutions before
disassembling pump.
Cause
Solution
Restricted line or inadequate air
supply.
Clear; increase air supply.
Dirty or damaged air motor.
Service air motor (see 306–982).
Clogged fluid hose, valve, or nozzle.
Clear.*
Restricted line or inadequate air
supply.
Clear; increase air supply.
Exhausted fluid supply.
Refill; reprime or flush.
Clogged fluid hose, valve, or nozzle.
Clear.*
Loose packing nut or worn throat
packings.
Tighten packing nut (see page 8);
replace throat packings.
Piston and intake valves need adjustment.
Adjust; see manual 307–983.
Pump operates but output is low on
downstroke.
Held open or worn intake valve.
Clear; service. See manual
307–983.
Pump operates but output is low on
upstroke.
Held open or worn fluid piston valve
or packings.
Clear; service. See manual
307–983.
Erratic or accelerated operation.
Exhausted fluid supply.
Refill; reprime or flush.
Piston and intake valves need adjustment.
Adjust; see manual 307–983.
Held open or worn intake valve.
Clear; service. See manual
307–983.
Held open or worn fluid piston valve
or packings.
Clear; service. See manual
307–983.
Pump operates but output is low on
both strokes.
* To determine if the fluid hose or gun is obstructed, follow the Pressure Relief Procedure on page 8. Disconnect the fluid hose and place a container at the pump fluid outlet to catch any fluid. Turn on the air just enough to
start the pump (about 20–40 psi [1.4–2.8 bar]). If the pump starts when the air is turned on, the obstruction is in
the fluid hose or dispense valve.
Service
Disconnecting the Displacement Pump
NOTE: For displacement pump repair instructions,
refer to the separate displacement pump manual
307–983, supplied.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
1. Flush the pump if possible. Stop the pump at the
bottom of its stroke. Relieve the pressure.
2. Disconnect all hoses and remove the pump from
its mounting.
6. Turn on the air to the motor and run the pump
slowly. Adjust the locknuts (14) on the return
mounting tube (11) as necessary until the pump
operates smoothly at minimum air pressure to the
motor. Tighten the locknuts securely.
7. Reconnect the ground wire if it was disconnected
during repair.
8. If the pump is not immersed, fill the packing nut/
wet-cup 1/2 full of compatible solvent.
1
Torque to 65–75 ft-lb (88–102 N.m).
2
Use thread sealant when reinstalling.
3
Lubricate.
3. Unscrew the coupling nut (17) from the displacement rod (R). Remove the coupling collars (18).
See Fig. 4.
1
4. Unscrew the lower locknut (14) and lockwasher
(13) from the return mounting tube (11).
5. Unscrew the swivel union (S) from the supply
mounting tube (12).
2
CAUTION
11
If you are removing the mounting tubes, wrench the
tubes close to the motor base to prevent thread
damage in the base. Use thread sealant on the male
threads when reinstalling.
17
7
3
5
2
2
Reconnecting the Displacement Pump
1. Position the displacement pump on the mounting
tubes (11, 12). Thread the upper locknut (14) onto
the return mounting tube (11) a couple of turns.
Tighten the swivel union (S) securely onto the
supply mounting tube (12). See Fig. 4.
14
12
18
13
R
1
S
2. Butt the connecting rod (2) and displacement rod
(R) together; if necessary, adjust the locknuts (14)
on the return mounting tube (11) to align the rods.
3. Position the coupling collars (18) so they engage
with the connecting rod (2) and displacement rod
(R). Lower the coupling nut (17) over the coupling
collars and screw it securely onto the displacement
rod.
13
14
4. Tighten the locknuts (14) securely.
Fig. 4
5. Remount the pump and connect all hoses.
3
Parts
Model 224–757, Series C
4:1 Ratio President Pump, Stubby Size
Includes items 1–18
Ref
No.
Part
No.
1
205–038
2
190–069
3
224–756
5
7
11
100–579
156–082
181–120
12
190–178
13
14
162–648
160–026
17
18
190–065
190–066
Description
AIR MOTOR, President
See 306–982 for parts
ROD, connecting;
5.69” (144.5 mm) long
PUMP, displacement
See 307–983 for parts
PIN, cotter
O-RING; nitrile rubber
TUBE, return;
12.812” (325.4 mm) long
TUBE, supply;
6.75” (171.5 mm) long
LOCKWASHER, ext shakeproof
NUT, special lock;
3/4 garden hose thread
NUT, coupling
COLLAR, coupling
Qty
1
1
1
1
1
1
1
17
11
1
2
2
1
2
7
5
2
14
12
18
13
13
3
14
Dimensions
Mounting Hole
Layout
0.375”
(9.52 mm)
diameter
2.254”
(57.25 mm)
2.254”
(57.25 mm)
B
3.188”
(80.97 mm)
A
2.625”
(66.67 mm)
5.250”
(133.4 mm)
3/4 npt(f)
return
1” npt(f)
outlet
NOTE: Use mounting gasket 161–322.
C
06088
Manual
Change Summary
06112
Model No.
A
B
C
224–757
36.5 in.
(927 mm)
16.5 in.
(419 mm)
20 in.
(508 mm)
14
308-159
Assembly
Changed
Part
Status
Ref.
No.
Part No.
Name
Model
224–757, to
Series C
Added
17
190–065
Coupling Nut
Added
18
190–066
Collars
Old
New
Old
New
2
2
12
12
219–071
190–069
181–121
190–178
Conn. Rod
Conn. Rod
Supply Tube
Supply Tube
Technical Data
Category
Data
Ratio
4:1
Maximum fluid working pressure
400 psi (28 bar)
Maximum air input pressure
100 psi (7 bar)
Pump cycles per 1 gallon (3.8 liters)
8.25
Fluid flow at 60 cycles per minute
8 gpm (30 liters/min)
Fluid inlet size
1–1/2 npt(f)
Fluid outlet size
1 in. npt(f)
Air inlet size
1/2 npt(f)
Weight
47 lb (21.32 kg)
Maximum pump operating temperature
180_F (82_C)
* Sound level at 100 psi, 60 cycles per minute
94 dBa
* Sound power level at 100 psi, 60 cycles per minute
109 dBa
Wetted parts
Supply and Return Tubes: Nickel-plated carbon steel
Air Motor Base: Aluminum
Displacement Pump: Refer to manual 307–983
* Tested in accordance with ISO 3744.
KEY:
Fluid Outlet Pressure – Black Curves
Air Consumption – Gray Curves
cycles per min
psi 400
28
bar
350
24.5
A
B
C
17
100 psi (7 bar) air pressure
70 psi (4.9 bar) air pressure
40 psi (2.8 bar) air pressure
33
50
66
40.0 scfm
1.120 m#/min
35.0
0.980
A
300
21
30.0
0.840
250
17.5
25.0
0.700
B
200
14
20.0
0.560
150
10.5
15.0
0.420
A
C
100
7
10.0
0.280
B
50
3.5
5.0
0.140
C
0
gpm
liters/min
0
2
4
6
7.6
15.2
22.8
8
30.4
FLUID FLOW (TEST FLUID: NO 10 MOTOR OIL)
To find Fluid Outlet Pressure (bar/psi) at a specific fluid flow (lpm/
gpm) and operating air pressure (bar/psi):
1. Locate desired flow along bottom of chart.
2. Follow vertical line up to intersection with selected fluid outlet
pressure curve (black). Follow left to scale and read fluid outlet
pressure.
To find Pump Air Consumption (m#/min or scfm) at a specific fluid
flow (lpm/gpm) and operating air pressure (bar/psi):
1. Locate desired flow along bottom of chart.
2. Follow vertical line up to intersection with selected air consumption curve (gray). Follow right to scale and read air consumption.
Graco Warranty and Limitation of Liability
WARRANTY
Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects
in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. Graco will,
for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear
caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident,
tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by
the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor
for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective
parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not
disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the
costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no
other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two
(2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS, OR COMPONENTS
SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors,
switches, hose, etc.) are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.
For Sales to Canadian Customers:
Except as expressly stated herein, Graco makers no representations, warranties or conditions, express, implied or collateral, concerning any goods or services sold, and GRACO SHALL NOT BE LIABLE IN ANY MANNER FOR any other representation,
warranty or condition of any kind, whether arising by operation of law or otherwise, including but not limited to, WARRANTIES OF
MERCHANTABLE QUALITY OR FITNESS FOR A PARTICULAR PURPOSE.
LIMITATION OF LIABILITY
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or for the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of
contract, breach of warranty, the negligence of Graco, or otherwise.
Graco Phone Number
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:
1–800–367–4023 Toll Free
Sales Offices: Atlanta, Chicago, Detroit, Los Angeles
Foreign Offices: Belgium, Canada, England, Korea, Switzerland, France, Germany, Hong Kong, Japan
GRACO INC.
P.O. BOX 1441 MINNEAPOLIS, MN
55440–1441
PRINTED IN U.S.A. 308–159 January 1992 Revised April 1996
16
308-159

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project