advertisement
Euphonix Media Application Controller
Single Workstation Installation Guide
Document Revision
: C
Software Version
: 1.1.3 & higher
Part Number
: 840-10049-02
Release Date
: November 2006
Euphonix, Inc.
220 Portage Ave.
Palo Alto, California 94306
Phone: 650-855-0400
Fax: 650-855-0410
Web: http://www.euphonix.com
e-mail: [email protected]
Media Application Controller Single Workstation Install Guide
Table of Contents
Chapter 1: Hardware Connections and MC Client Setup
.............................5
Network Configuration..............................................................................6
MC Standalone............................................................................6
System 5-MC ..............................................................................6
EuCon Software Installation......................................................................7
Workstation Connection and Control........................................................8
Chapter 2: Logic Pro
.......................................................................................................11
Chapter 3: Nuendo–PC and Mac
..............................................................................13
Chapter 4: Pro Tools
.......................................................................................................15
Workstation Configuration......................................................................15
Pro Tools Configuration ..........................................................................16
Chapter 5: Pyramix
..........................................................................................................19
Chapter 6: Support and Troubleshooting
...........................................................23
Appendix A:DAW Parts List and Schematics
....................................................25
iii
Media Application Controller Single Workstation Install Guide
Chapter 1: Hardware Connections and MC Client Setup
Schematics and parts are listed for each DAW setup in Appendix A:
.
1.1
Connect the MC
1.
Unpack the MC from its packaging and select a place to put it. The MC should go on a hard flat surface in order to allow proper ventilation. (System 5-MC has its own frame for the MC and CM408T modules).
NOTE: The MC and CM408T modules require sufficient ventilation space on the bottom. The MC has detachable feet for standalone users without a System 5 frame, but the CM408T modules do not. If you do not use a System 5 frame, you MUST have at least 1 inch of clearance under the CM408T modules and
MC or damage to the units may occur.
Use Figure 1-1 as a reference to connect the MC to its components.
VGA KEYBOARD USB
FOOT
SWITCH HEADPHONES
DC IN TALKBACK MIC
VGA and
Keyboard
USB Talkback Mic Output LAN Foot
Switch
Headphone DC In
Figure 1-1
MC Rear Panel
2.
Plug the power supply into the
DC In
port on the right side as you look at the rear panel.
Be careful plugging this in as the connector has easily-bent pins. When the pins are seated, twist the ring on the connector’s side until it locks. Do not turn on the MC yet; network configuration must be completed first.
WARNING: Attach power supply to the MC BEFORE plugging into AC power or the unit may be damaged.
5
Media Application Controller Single Workstation Install Guide Hardware Connections and MC Client Setup
1.2
Network Configuration
1.2.1
MC Standalone
Using one of the RJ-45 Ethernet (included) cables, connect your workstation to one of the
LAN
ports on the Netgear RP614 router. Then connect the MC to one of the other
LAN ports on the Netgear router.
NOTE: You have now created a small local area network comprised of just the MC and your workstation. If you wish to have access to an outside network, either a studio facility LAN or the Internet, connect the WAN port on the Netgear to your studio’s network switch, or to your cable/DSL modem.
The MC ships with DHCP enabled, allowing it to automatically obtain an IP address.
The Netgear RP614 has a DHCP server and hands out IP addresses to the devices connected to its LAN ports (the MC and your workstation). This allows for easy plug and play network configuration. For this reason, the Netgear router must be turned on before the MC and your workstation.
1.2.2
System 5-MC
1.
Connect the MC and CM408T modules to
LAN
ports on the SonicWALL 1260 router.
2.
Connect your workstation to a
LAN
port on the SonicWALL.
The MC ships with DHCP enabled, allowing it to automatically obtain an IP address. The SonicWALL ships from Euphonix with its DHCP server enabled, such that it hands out IP addresses to the MC, CM408T modules, and your workstation. For this reason the SonicWALL must be turned on before the MC,
CM408T modules, and your workstation.
6
Media Application Controller Single Workstation Install Guide Hardware Connections and MC Client Setup
1.3
EuCon Software Installation
1.
Insert the
Euphonix MC Software Installation
CD in your workstation’s CD/
DVD drive.
2.
In Mac OS X, double-click the CD icon on the desktop, and double-click the
EuConWS
package.
The Install program launches. Proceed to Step 4.
3.
In Windows, if AutoRun is enabled, the setup program starts from the CD automatically. If AutoRun is
not
enabled: a. Minimize all programs. b. Double-click
My Computer
on the desktop to display the drives on your computer. c. Double-click the CD/DVD drive. d. Double-click the
EuConWS
executable file.
The Setup Wizard begins running.
4.
Click
Next
and choose a directory to install the software.
The default Windows directory is C:\Program Files\Euphonix\EuCon.
The default Macintosh OS X directory is the Applications folder.
5.
For Windows installations, click
Next
to customize the software components to install.
EuCon Workstation Core
is automatically selected (this is the basic software used to communicate with the MC. Select further options according to your DAW: a. For Nuendo workstations, select only the
EuCon adapter for Nuendo
and
VST plugin layouts for Nuendo
options. b. For Pyramix, select only the
EuCon adapter for Pyramix
option.
c. For all other DAWs, select only the
Studio Monitor Express
option.
6.
Click
Next
to continue.
7.
Select locations for application shortcuts in the
Start
menu.
The default is a
EuCon
folder in the
Start
menu with shortcuts to the MC’s applications.
8.
Click
Next
to continue.
The Wizard now displays a summary of all options selected during the setup process. To change them, click
Back
until the desired setup option appears.
7
Media Application Controller Single Workstation Install Guide Hardware Connections and MC Client Setup
9.
Click
Install
.
The Wizard installs the selected components to your workstation.
10.
Click
Finish
to exit the Wizard.
NOTE: When first running the MC Client, the Windows Firewall may ask whether to block or unblock MC Client and EuCon Discovery from accessing the Internet or local area network. Because all communication between the MC Client and the MC occurs through the workstation's network connection, you must select
Unblock or it will not communicate with the MC.
1.4
Workstation Connection and Control
1.
To connect the MC to your workstation, make sure the MC Client is running on your workstation, and then press the Strip Control
Setup
key on the right side of the MC.
Layouts
Setup
Setup
Strip Control
Setup
key
Figure 1-2
Strip Control Setup key
The Touchscreen in Figure 1-3 opens and displays all workstations available
on the network on the right. There are two choices: none/disconnect and your workstation (showing computer name, user name, and operating system).
(Figure 1-3 displays a multiple workstation setup).
8
Media Application Controller Single Workstation Install Guide Hardware Connections and MC Client Setup
Figure 1-3
Workstation Touchscreen
2.
Touch the desired Workstation key on the left of the Touchscreen.
These buttons map to the physical
Workstation Keys
on the upper right of the
MC. For simplicity in single workstation setups, Euphonix suggests using the
1
key.
Workstation
1 2
3
4
Figure 1-4
Workstation keys
3.
Touch your workstation in the list to assign it to the selected number.
4.
Press the Strip Control
Setup
key again to exit Workstation assignment mode.
5.
Press the
Workstation
key to which you assigned your workstation to control your workstation. The MC’s right-hand trackball (which acts as the mouse) and keyboard should now function just as if they were connected directly to your workstation.
9
Media Application Controller Single Workstation Install Guide Hardware Connections and MC Client Setup
1.5
Ready to Proceed
You have successfully connected your MC to your workstation. Proceed to the chapter of this installation guide for your DAW software to configure it to work with the MC.
10
Media Application Controller Single Workstation Install Guide
Chapter 2: Logic Pro
Logic Pro (version 7.2.1 and higher) has EuCon support and connectivity built into the application. With the MC Client running on your Macintosh, load Logic Pro, and the
MC automatically connects to the application and displays the Logic Pro application set.
Versions of Logic prior to 7.2.1 do not have EuCon support. However, the updates for
Logic are part of Apple’s Software Update program, so simply check for new updates
(
Apple Menu-> System Preferences -> Software Update -> Check Now
), download, and install the Logic 7.2.1 update. Then re-open Logic and the MC will connect. You have now successfully set up the MC to operate with your Logic Pro workstation.
• See the MC Operation Manual to learn about the MC’s application sets, touchscreens, and any other information.
• Check the Euphonix website ( www.euphonix.com
) for technical bulletins, product support notices, and new software releases.
• Please register your MC by filling out the online registration form at www.euphonix.com/registration . Registration is required to download software updates.
11
Media Application Controller Single Workstation Install Guide Logic Pro
12
Media Application Controller Single Workstation Install Guide
Chapter 3: Nuendo–PC and Mac
To enable Nuendo to work with the MC, you must obtain a Nuendo EuCon Adapter license from Euphonix and download it to your Nuendo USB protection device (dongle):
1.
Close all open applications. Make sure your Syncrosoft USB dongle is plugged into your Nuendo workstation.
2.
Start the Syncrosoft License Control Center by choosing
Start Menu->Steinberg Nuendo 3->License Control Center
.
Windows
: Click
Start Menu->Syncrosoft->License Control Center
.
OS X
: Navigate to the
Applications\Syncrosoft
folder and run
License
Control Center
.
3.
Choose
License Download
from the
Wizards
menu.
Choose
License Transfer
to transfer an existing Nuendo EuCon license to a new USB dongle.
4.
When prompted, enter the activation code for Nuendo EuCon provided by
Euphonix.
5.
Make sure you are downloading the correct license, then click
Next
.
6.
If you have more than one Syncrosoft USB dongle attached to your workstation, select the one onto which you wish to download the license. Click
Next
.
7.
Press
Download
to transfer the license onto your USB dongle.
8.
Close the wizard and open Nuendo.
The Nuendo EuCon Adapter must be installed during the EuConWS software installation
(see page 7). Note that this is the MC Client’s Nuendo adapter. For Nuendo to commu-
nicate with the MC, Nuendo’s EuCon device must be added in the Nuendo Device Setup dialog:
1.
Choose
Device Setup
from Nuendo’s
Devices
menu.
The Device Setup dialog opens.
2.
Click the + button (add) on the top-left.
A drop-down list of devices appears.
EuCon
should appear near the top of the list. If not, check that you have successfully downloaded the license for the Eu-
Con Adapter to your USB dongle using the License Control Center.
13
Media Application Controller Single Workstation Install Guide Nuendo–PC and Mac
3.
Select
EuCon
from the drop-down list.
The EuCon device is added and the MC surface immediately updates with the
Nuendo default Application Set to reflect the open Nuendo project. For the
System 5-MC, the MC auto-assigns the Nuendo channels to the CM408T strips, beginning with channel 1 on the first CM408T’s leftmost strip.
Steinberg has created a default Nuendo Application Set with the most commonly used functions and commands.
14
Media Application Controller Single Workstation Install Guide
Chapter 4: Pro Tools
4.1
Workstation Configuration
After installing the EuCon software and restarting your Mac, the MC Client launches automatically upon startup of OS X and EuCon applications can now function.
To configure your HUI or Mackie Control applications to work with the MC:
1.
Click
Apple Menu-> System Preferences
.
The System Preferences dialog opens.
2.
Click on EuPrefsPane.
The Euphonix Preferences pane opens.
Figure 4-1
Euphonix Preferences pane
3.
Open a Finder window and navigate to the folder containing the HUI or Mackie
Control application(s) you wish to use.
4.
Drag the application(s) into the Euphonix Preferences pane.
15
Media Application Controller Single Workstation Install Guide Pro Tools
NOTE: You must drag the actual application icon into the preferences pane, not a shortcut or alias!
5.
For each application, select
HUI
or
Mackie Control
from the drop-down menu under
Protocol
, and select the MIDI ports for the application to use.
NOTE: The EuCon software sets up a virtual MIDI driver with 32 ports, and each application can use up to four (the limit with HUI applications). Keep track of which application uses which ports in order to configure them properly.
6.
Close the Euphonix Preferences pane. When prompted, restart your Macintosh.
7.
Connect the MC to the Macintosh.
4.2
Pro Tools Configuration
To configure Pro Tools to recognize the MC:
1.
Launch Pro Tools.
2.
Choose
Peripherals
from the Operations menu.
The Peripherals dialog opens.
3.
Click the
MIDI Controllers
tab.
Figure 4-2
Pro Tools Peripherals dialog
16
Media Application Controller Single Workstation Install Guide Pro Tools
Pro Tools has configuration boxes for the four possible controllers. MC standalone users need to configure only one controller. System 5-MC users need to configure
one controller for each CM408T module
because the MC mirrors one CM408T and does not require an extra HUI controller.
4.
For each controller you use, select
HUI
from the
Type
drop-down menu.
5.
Configure each controller to have the input and output MIDI ports set for Pro-
Tools in the Euphonix Preferences Pane. Click on the
Receive From
and
Send
To
drop-down menus, hover over
Predefined
, then select from the Euphonix
MIDI ports.
For example, if you set ProTools to use MIDI ports 9–12, your first HUI controller’s receive and transmit ports should be set to
EphMIDIEP9
.
Figure 4-3
Excerpt from Pro Tools MIDI menu
6.
Select
8
from the
Ch #
drop-down menu as the number of channels for each controller.
7.
Press
OK
.
The MC updates the channel and track information.
17
Media Application Controller Single Workstation Install Guide Pro Tools
18
Media Application Controller Single Workstation Install Guide
Chapter 5: Pyramix
To enable the use of the MC with Pyramix, the
EuCon adapter for Pyramix
checkbox
must be selected during the MC Client software installation (see page 7). Then add the
MC as an installed controller in Pyramix:
1.
Launch the Pyramix Virtual Studio software.
2.
Press the
Pref
key on the top bank of the MC Soft Keys.
The bank changes to show two options:
Home
: Restores the first bank of soft keys
Show Settings
: Opens the Pyramix Settings dialog box (alternatively, choose
All Settings
from the
Settings
menu in Pyramix Virtual Studio).
3.
Click
Show Settings
.
A dialog appears showing a list of the various types of adjustable settings on the left side.
19
Media Application Controller Single Workstation Install Guide Pyramix
Figure 5-1
Pyramix Settings
4.
Click
Controller
.
The right pane shows any installed controllers. However, at this point the pane is empty unless other interface controllers have been installed previously.
20
Media Application Controller Single Workstation Install Guide
5.
Click the
Add
button.
The Controller Properties dialog opens.
Pyramix
Figure 5-2
Controller Properties dialog
6.
Type the desired name for the MC in the
Name
field (i.e.,
MC in Studio 2
).
7.
Select the
Enable
checkbox.
8.
Choose
OASIS
from the
Driver
drop-down selection box.
9.
Click the
Properties
button next to the
Driver
selection box.
The OASIS Configuration Properties dialog opens.
Figure 5-3
OASIS Configuration Properties dialog
10.
Select
EuCon
from the
Transport
drop-down menu.
If
EuCon
is not in the drop-down menu, it is probably because the MC Client is not running. Check that the MC Client menu tray icon is present. If not, launch the MC Client using the shortcuts in the
Start
menu or the
Euphonix
folder.
21
Media Application Controller Single Workstation Install Guide Pyramix
Leave the
Station ID
at its default setting of 1 unless you have multiple controllers, in which case simply increment the setting (i.e., if two controllers are installed, set the
Station ID
= 3 for the MC).
11.
Press
OK
to exit that dialog, press
OK
on the Controller Properties dialog and press
OK
on the General Settings dialog.
12.
Close Pyramix, reboot the workstation, and then open Pyramix Virtual Studio.
Pyramix will not connect to the MC properly without rebooting the workstation.
The MC will now load the default Pyramix Application Set if a project is open. Otherwise, the Application Set will
not
be loaded, but the Soft Keys at the top-left illuminate to show that EuCon communication is enabled.
22
Media Application Controller Single Workstation Install Guide
Chapter 6: Support and Troubleshooting
The MC is a professional control surface engineered with industrial-grade components, and it should operate reliably in your studio setup. It is, however, a complex device and issues can arise due to environmental or other factors. Euphonix provides a one year warranty on the MC and CM408T modules.
If you are having trouble with your MC, these sections can either resolve the problem or provide useful troubleshooting information for our technical support personnel.
6.1
Support
Euphonix maintains a support section for the MC on our website: http://www.euphonix.com/support/mc.htm
. This page has the latest versions of:
• the EuCon software (for both workstations and the MC);
• this manual;
• constantly expanding FAQ section.
You must sign up for a user account to download new versions of the EuCon software.
If you cannot find an answer for your question in this manual, consult the FAQ section to see if it is answered there.
Those who purchased their MC through a VAR (
value-added reseller
), such as Guitar
Center Pro, are supported by that reseller. Euphonix does not provide service directly to VAR customers. This avoids confusion between Euphonix and your VAR regarding your MC and its support needs. System 5-MCs are supported only by Euphonix.
6.2
Troubleshooting
If you are having problems with your MC or System-5 MC:
1.
2.
Then try the Euphonix website’s FAQ or technical bulletins.
3.
If you still are unable to solve your issue, contact your VAR (if applicable) or
Euphonix for support.
Our technical support phone hours (650-855-0412) are Monday through Friday
9 AM – 5 PM. The website is always available.
23
Media Application Controller Single Workstation Install Guide Support and Troubleshooting
Common Issues and Solutions
My MC does not turn on.
Make sure the MC’s power connector is securely connected. Push on it lightly to seat it, twist the outer ring to lock it onto the MC, and make sure the transformer is plugged into the wall.
The MC cannot connect to a workstation; the workstation does not appear in the
MC's Workstation Setup screen
.
• Make sure the MC Client is installed on the workstation, and that the Windows
Firewall is not blocking the MC Client and EuCon Discovery applications.
• The MC, CM408T modules, and workstation must be connected to the same network segment (router/switch): the Netgear RP614 or SonicWALL 1260.
• Both the workstation and MC must have the
same
version of the EuCon software.
• To further troubleshoot this issue, we recommend using a cross-over cable between the MC and one workstation, to remove network variables from the equation. Once this setup is working, re-connect the MC and workstation(s) to the switch/router, and verify proper operation.
The MC does not connect to Nuendo.
• The Nuendo EuCon Adapter must also be installed when installing the EuCon software on your workstation. Make sure Studio Monitor Pro is
NOT
installed, as SME usurps Nuendo when installed on the same machine.
• Make sure your Nuendo license includes EuCon connectivity, and that you have added the EuCon device in Nuendo Device Setup.
• Make sure the MC is properly connected to the workstation. The MC’s Main
Touchscreen should display the network name of your workstation in the upper left-hand corner.
The MC does not connect to Pyramix.
• The Pyramix EuCon Adapter must also be installed when installing the EuCon software on your workstation. Make sure Studio Monitor Pro is
NOT
installed, as SME interferes with Pyramix-MC connectivity.
• Verify that the Pyramix connection procedure has been properly executed, and that the MC is properly connected to the workstation.
The talkback mic does not produce any audio.
The talkback mic is a condenser microphone and the XLR output is at mic level so it must be connected to a pre-amp with +48V phantom power.
24
Media Application Controller Single Workstation Install Guide
Appendix A: DAW Parts List and Schematics
The following diagrams illustrate how to use the supplied parts to interconnect the MC with the supported DAWs.
25
Apple Logic Pro / Euphonix Media Controller Installation
Required Parts
QTY
MC Only
1 Euphonix MC Controller
1 Apple 20" Cinema Display
1 Netgear RP614 DHCP Router/Switch
(included with MC packout)
1 USB Memory Stick (for app sets and configuration data)
1 DVI M-M
(included with Cinema Display packout)
2 Ethernet Cable
(included with MC packout)
1 Apple G5 Workstation fitted:
1 Apple Logic Pro 7.21 or higher
1 Apogee Ensemble Audio Interface
QTY
System 5 MC (32 Fader shown)
DESCRIPTION
1 Euphonix 32 Fader System 5 MC
1 Sonic Wall Pro 1260 DHCP Router/Ethernet Switch
1 Apple 20" Cinema Display
1 DVI Cable M-M
(included with Cinema Display packout)
6 Ethernet Cable
1 USB Memory Stick (for app sets and configuration data)
1 Apple G5 Workstation fitted:
1 DVI Cable M-M
1 Apple Logic Pro (V7.2 or higher)
1 Apogee Ensemble Audio Interface
MC_LogicPro_Install_AdditionalItems_V1-3 5/10/2006
F
E
D
C
B
A
H
G
WAN
USB
MEMORY STICK
WAN
NETGEAR
RP614
NET 1
NET 2
NET 3
NET 4
1 2
APPLE G5
LOGIC PRO
NET 1
NET 2
DVI OUT
PCIe
USB
USB
USB
FW400
1
2
3
EUPHONIX
MC CONTROLLER
4 5
DVI IN
APPLE
CINEMA DISPLAY
USB
6 7
1
1
2
3
4
2
3
4
MIC
IN
LINE
IN
WC
IN
1
2
FIRE
WIRE
APOGEE
ENSEMBLE
LINE
OUT
1
2
3
4
5
6
7
8
WC
OUT
8 9 10 11
Comments
Legend:
ANALOG
DVI
NETWORK
FIREWIRE
USB
B
A
D
C
F
E
H
G
EUPHONIX SYSTEM
5MC
FADERS 1-8
EUPHONIX SYSTEM
5MC
FADERS 9-16
EUPHONIX
MC CONTROLLER
EUPHONIX SYSTEM
5MC
FADERS 17-24
EUPHONIX SYSTEM
5MC
FADERS 25-32
USB
MEMORY STICK
1 2
APPLE G5
LOGIC PRO
NET 1
NET 2
DVI OUT
PCIe
USB
USB
USB
FW400
1
2
3 4 5
DVI IN
APPLE
CINEMA DISPLAY
USB
6 7
1
1
2
3
4
2
3
4
MIC
IN
LINE
IN
WC
IN
1
2
FIRE
WIRE
APOGEE
ENSEMBLE
LINE
OUT
1
2
3
4
5
6
7
8
WC
OUT
8 9
1
2
10
11
12
7
8
9
3
4
5
6
PORTS
SONIC WALL 1260
ROUTER/SWITCH
PORTS
13
14
22
23
24
19
20
21
15
16
17
18
10 11
Comments
Legend:
ANALOG
DVI
NETWORK
FIREWIRE
USB
Nuendo PC / Euphonix Media Controller Installation
Required Parts
MC Only
QTY
1 Euphonix MC Controller
1 Apple 20" Cinema Display
1 Netgear RP614 DHCP Router/Switch
(included with MC packout)
1 DVI M-M
(included with Cinema Display packout)
2 Ethernet Cable
(included with MC packout)
1 USB Memory Stick (for app sets and configuration data)
1 PC Audio Labs (or equivalent) Workstation fitted:
1 Nuendo V3.2
(PC Version)
1 Euphonix Nuendo EUCON License
1 RME Fireface 400
1 Firewire Cable
QTY
System 5 MC
(32 Fader shown)
DESCRIPTION
1 Euphonix 32 Fader System 5 MC
1 Sonic Wall Pro 1260 DHCP Router/Ethernet Switch
1 Apple 20" Cinema Display
1 DVI Cable M-M
(included with Cinema Display packout)
6 Ethernet Cable
1 USB Memory Stick (for app sets and configuration data)
1 PC Audio Labs (or equivalent) Workstation fitted:
1
Nuendo V3.2.1
(PC Version)
1 Euphonix Nuendo EUCO License
1 RME Fireface 400
1 Firewire Cable
MC_NUENDO_PC_Install_AdditionalItems_V1-2 5/10/2006
F
E
D
C
B
A
H
G
WAN
USB
MEMORY STICK
WAN
NETGEAR
RP614
NET 1
NET 2
NET 3
NET 4
1
PC AUDIO LABS
NUENDO 3.2
NET 1
NET 2
DVI OUT
PCI
USB
USB
USB
FW400
1
2
2 3
EUPHONIX
MC CONTROLLER
4 5
DVI IN
APPLE
CINEMA DISPLAY
USB
6 7
3
4
1
1
2
2
3
4
MIC
IN
INST
IN
LINE
IN
ADAT IN
SPDIFIN
RME
FIREFACE 400
LINE
OUT
3
4
5
1
2
6
7
8
ADAT OUT
SPDIF OUT
1
2
FIRE
WIRE
8 9 10 11
Comments
Legend:
ANALOG
DVI
NETWORK
FIREWIRE
USB
B
A
D
C
F
E
H
G
USB
MEMORY STICK
1
PC AUDIO LABS
NUENDO 3.2
NET 1
NET 2
DVI OUT
PCI
USB
USB
USB
FW400
1
2
2 3
EUPHONIX SYSTEM
5MC
FADERS 1-8
EUPHONIX SYSTEM
5MC
FADERS 9-16
EUPHONIX
MC CONTROLLER
EUPHONIX SYSTEM
5MC
FADERS 17-24
EUPHONIX SYSTEM
5MC
FADERS 25-32
4 5
DVI IN
APPLE
CINEMA DISPLAY
USB
6 7
3
4
1
1
2
2
3
4
MIC
IN
INST
IN
LINE
IN
ADAT IN
SPDIFIN
RME
FIREFACE 400
LINE
OUT
3
4
5
1
2
6
7
8
ADAT OUT
SPDIF OUT
1
2
FIRE
WIRE
8 9
1
2
10
11
12
7
8
9
3
4
5
6
PORTS
SONIC WALL 1260
ROUTER/SWITCH
PORTS
13
14
22
23
24
19
20
21
15
16
17
18
10 11
Comments
Legend:
ANALOG
DVI
NETWORK
FIREWIRE
USB
Nuendo Apple / Euphonix Media Controller Installation
Required Parts
MC Only
QTY
1 Euphonix MC Controller
1 Apple 20" Cinema Display
1 Netgear RP614 DHCP Router/Switch
(included with MC packout)
1 DVI M-M
(included with Cinema Display packout)
2
Ethernet Cable
(included with MC packout)
1 USB Memory Stick (for app sets and configuration data)
1 Apple G5 Workstation fitted:
1
Nuendo V3.2.1
(MAC V ersion)
1 Euphonix Nuendo EUCON License
1 RME Fireface 400
1 Firewire Cable
QTY
System 5 MC
(32 Fader shown)
DESCRIPTION
1 Euphonix 32 Fader System 5 MC
1 Sonic Wall Pro 1260 DHCP Router/Ethernet Switch
1 Apple 20" Cinema Display
1 DVI Cable M-M
(included with Cinema Display packout)
6 Ethernet Cable
1 USB Memory Stick (for app sets and configuration data)
1 Apple G5Workstation fitted:
1
Nuendo V3.2.1
(MAC Version)
1 Euphonix Nuendo EUCO License
1 RME Fireface 400
1 Firewire Cable
MC_NUENDO_MAC_Install_AdditionalItems_V1-2 5/10/2006
F
E
D
C
B
A
H
G
WAN
USB
MEMORY STICK
WAN
NETGEAR
RP614
NET 1
NET 2
NET 3
NET 4
1
Apple G5
NUENDO 3.2.1
NET 1
NET 2
DVI OUT
PCIe
USB
USB
USB
FW400
1
2
2 3
EUPHONIX
MC CONTROLLER
4 5
DVI IN
APPLE
CINEMA DISPLAY
USB
6 7
3
4
1
1
2
2
3
4
MIC
IN
INST
IN
LINE
IN
ADAT IN
SPDIFIN
RME
FIREFACE 400
LINE
OUT
3
4
5
1
2
6
7
8
ADAT OUT
SPDIF OUT
1
2
FIRE
WIRE
8 9 10 11
Comments
Legend:
ANALOG
DVI
NETWORK
FIREWIRE
USB
B
A
D
C
F
E
H
G
USB
MEMORY STICK
1
Apple G5
NUENDO 3.2.1
NET 1
NET 2
DVI OUT
PCIe
USB
USB
USB
FW400
1
2
2 3
EUPHONIX SYSTEM
5MC
FADERS 1-8
EUPHONIX SYSTEM
5MC
FADERS 9-16
EUPHONIX
MC CONTROLLER
EUPHONIX SYSTEM
5MC
FADERS 17-24
EUPHONIX SYSTEM
5MC
FADERS 25-32
4 5
DVI IN
APPLE
CINEMA DISPLAY
USB
6 7
3
4
1
1
2
2
3
4
MIC
IN
INST
IN
LINE
IN
ADAT IN
SPDIFIN
RME
FIREFACE 400
LINE
OUT
3
4
5
1
2
6
7
8
ADAT OUT
SPDIF OUT
1
2
FIRE
WIRE
8 9
1
2
10
11
12
7
8
9
3
4
5
6
PORTS
SONIC WALL 1260
ROUTER/SWITCH
PORTS
13
14
22
23
24
19
20
21
15
16
17
18
10 11
Comments
Legend:
ANALOG
DVI
NETWORK
FIREWIRE
USB
ProTools LE7 / Euphonix Media Controller Installation
Required Parts
MC Only
QTY
1 Euphonix MC Controller
1 Apple 20" Cinema Display
1 Netgear RP614 DHCP Router/Switch
(included with MC packout)
2 Ethernet Cable
(included with MC packout)
1 USB Memory Stick (for app sets and configuration data)
1 Apple G5 Workstation fitted:
1
DigiDesign ProTools LE7
(or higher)
1 DigiDesign 007 Rack
QTY
System 5 MC
(32 Fader shown)
DESCRIPTION
1 Euphonix 32 Fader System 5 MC
1 Sonic Wall Pro 1260 DHCP Router/Ethernet Switch
1 Apple 20" Cinema Display
1 DVI Cable M-M
(included with Cinema Display packout)
6 Ethernet Cable
1 USB Memory Stick (for app sets and configuration data)
1 Apple G5 Workstation fitted:
1
DigiDesign ProTools LE7
(or higher)
1 DigiDesign 007 Rack
MC_PToolsLE_Install_AdditionalItems_V1-1 5/10/2006
F
E
D
C
B
A
H
G
WAN
USB
MEMORY STICK
WAN
NETGEAR
RP614
NET 1
NET 2
NET 3
NET 4
1 2
APPLE G5
Protools LE
NET 1
NET 2
DVI OUT
PCIe
USB
USB
USB
FW400
1
2
3
EUPHONIX
MC CONTROLLER
4 5
DVI IN
APPLE
CINEMA DISPLAY
USB
6 7
1
1
2
3
4
2
3
4
MIC
IN
LINE
IN
Digidesign
002 Rack
LINE
OUT
1
2
3
4
5
6
7
8
1
2
FIRE
WIRE
8 9 10 11
Comments
Legend:
ANALOG
DVI
NETWORK
FIREWIRE
USB
B
A
D
C
F
E
H
G
USB
MEMORY STICK
1
APPLE G5
Pro Tools LE
NET 1
NET 2
DVI OUT
PCIe
USB
USB
USB
FW400
1
2
2 3
EUPHONIX SYSTEM
5MC
FADERS 1-8
EUPHONIX SYSTEM
5MC
FADERS 9-16
EUPHONIX
MC CONTROLLER
EUPHONIX SYSTEM
5MC
FADERS 17-24
EUPHONIX SYSTEM
5MC
FADERS 25-32
4 5
DVI IN
APPLE
CINEMA DISPLAY
USB
6 7
1
1
2
3
4
2
3
4
MIC
IN
LINE
IN
Digidesign
002 Rack
LINE
OUT
1
2
3
4
5
6
7
8
1
2
FIRE
WIRE
8 9
1
2
10
11
12
7
8
9
3
4
5
6
PORTS
SONIC WALL 1260
ROUTER/SWITCH
PORTS
13
14
22
23
24
19
20
21
15
16
17
18
10 11
Comments
Legend:
ANALOG
DVI
NETWORK
FIREWIRE
USB
Pyramix / Euphonix Media Controller Installation
Required Parts
MC Only
QTY
1 Euphonix MC Controller
1 Apple 20" Cinema Display
1 Netgear RP614 DHCP Router/Switch
(included with MC packout)
1 DVI M-M
(included with Cinema Display packout)
2 Ethernet Cable
(included with MC packout)
1 USB Memory Stick (for app sets and configuration data)
1 Merging Pyramix Workstation fitted:
1 Pyramix 5.0
(or higher)
1 Pyramix OASIS License
1 Euphonix Nuendo EUCON License
1 Pyramix Compatible PCI Sound Card
QTY
System 5 MC
(32 Fader shown)
DESCRIPTION
1 Euphonix 32 Fader System 5 MC
1 Sonic Wall Pro 1260 DHCP Router/Ethernet Switch
1 Apple 20" Cinema Display
1 DVI Cable M-M
(included with Cinema Display packout)
6 Ethernet Cable
1 USB Memory Stick (for app sets and configuration data)
1 Merging Pyramix Workstation fitted:
1
Pyramix 5.0
(or higher)
1 Pyramix OASIS License
1 Euphonix Nuendo EUCON License
1 Pyramix Compatible PCI Sound Card
MC_PYRAMIX_Install_AdditionalItems_V1-1 5/10/2006
F
E
D
C
B
A
H
G
WAN
USB
MEMORY STICK
WAN
NETGEAR
RP614
NET 1
NET 2
NET 3
NET 4
1 2
Pyramix PC
V5.0
NET 1
DVI OUT
Pyramix
Sound
Card
FW400
1
2
USB
3
EUPHONIX
MC CONTROLLER
DVI IN
APPLE
CINEMA DISPLAY
USB
4 5 6 7 8 9 10 11
Comments
Legend:
ANALOG
DVI
NETWORK
FIREWIRE
USB
B
A
D
C
F
E
H
G
USB
MEMORY STICK
EUPHONIX SYSTEM
5MC
FADERS 1-8
EUPHONIX SYSTEM
5MC
FADERS 9-16
EUPHONIX
MC CONTROLLER
EUPHONIX SYSTEM
5MC
FADERS 17-24
EUPHONIX SYSTEM
5MC
FADERS 25-32
1
Pyramix PC
V5.0
NET 1
DVI OUT
Pyramix
Sound
Card
FW400
1
2
USB
2 3 4 5
DVI IN
APPLE
CINEMA DISPLAY
USB
6 7 8
1
2
10
11
12
7
8
9
3
4
5
6
PORTS
SONIC WALL 1260
ROUTER/SWITCH
PORTS
13
14
22
23
24
19
20
21
15
16
17
18
9 10 11
Comments
Legend:
ANALOG
DVI
NETWORK
FIREWIRE
USB
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project