BSW Is THE Place - Broadcast Supply Worldwide

BSW Is THE Place - Broadcast Supply Worldwide
INTERFACE
INTERFACE
EQUIPMENT
EQUIPMENT
– ROUTERS AND SWITCHERS
BSW Is THE Place
8X4 Digital Audio Routing Switcher
The DAS 8.4 PLUS provides digital audio routing switching of any one of 8 AES
inputs to 4 AES outputs. Routing switching allows any one input to be assigned to
any/or all outputs. The DAS 8.4 may be controlled via front panel switches, contact
closures, 5-volt TTL/CMOS logic and/or the multi-drop RS-232 serial port. This new
‘PLUS’ version adds VU meters to the front panel and allows easy VU meter selection
to monitor any of the four outputs. The front panel is equipped with push buttons,
output assignment LEDs and a headphone jack. Internal audio activity/silence
sensors monitor all four-output channels. Each is equipped with front-panel ACT
LED indicators; alarm delay and restore duration are adjustable. Additional features:
24-bit/96 kHz D/A converter with analog balanced stereo output, 16x16 GPIO port,
screw terminals.
DAS8.4PLUS List $929.00
Contact BSW For Lowest Prices
"Robust and reliable."
ACS8.2PLUS
16x4 Active Stereo Matrix Switcher
The Broadcast Tools SS 16.4 provides true matrix audio switching of 16 stereo
inputs to 4 stereo plus 4 monaural outputs, for incredibly versatile audio switching.
Matrix switching allows any/or all inputs to be assigned to any/or all outputs. The
SS 16.4 may be controlled via front panel switches, contact closures, 5-volt TTL/
CMOS logic and/or the multi-drop RS-232 or RS-485 serial port. Installation is
simplified with removable screw terminals (Euro).
The ACS 8.2 PLUS cleanly provides matrix audio switching of 8 stereo inputs to 2
stereo plus 2 mono outputs. You can assign any or all inputs to any or all outputs,
with any input assigned to output one having fading capabilities. It features
connections plug-in Euroblock screw terminals for all audio and GPIO connections,
and it conforms to the Studio Hub format. A front panel monitor selection switch
lets you choose which stereo output the VU meter and headphone amplifier
monitors. Truly flexible, the ACS 8.2 Plus can be controlled via front panel switches,
contact closures, 5-volt TTL/CMOS logic, and/or the multi-drop RS-232 serial port.
• True matrix switching
• 3 switching modes: interlock, overlap and mix
• Logic functions via microprocessor and non-volatile memory
• Internal audio activity/silence sensors monitor all four-output channels, and each is
equipped with front panel "ACT" LED indicators
• Adjustable alarm delay and restore duration
• Power-up selection of inputs to outputs, mute or last source selected
• 16 user-configurable macros; 24 input GPI port (PIP) with LED indicator
• 16 open collector channel status outputs or programmable via burst commands
• 8 SPST relay outputs, programmable via burst commands
• Balanced stereo inputs and stereo/mono outputs
• Multidrop RS-232 or RS-485 serial port with data activity LED
• Multiple units may be cascaded to expand input
ACS8.2PLUS
SS16.4
8X2 Active Stereo Matrix Switcher
List $929.00 Contact BSW For Lowest Prices
List $1,319.00
Contact BSW For Lowest Prices
Analog and Digital Matrix Switcher
This feature-packed matrix switcher sports four stereo AES and four stereo analog
inputs along with two independent stereo analog and AES outputs in one rack
space. Each input is equipped with a 3-band EQ, five types of filters, and a leveler
function for maximum sonic flexibility. The ADMS 44.22 provides both word clock
in and word clock out signals for synchronization to external digital equipment.
Additionally, the four stereo AES inputs support high-quality real-time sample rate
conversion for connection with asynchronous digital sources. Each output channel
is equipped with an automatic level control circuit and parallel stereo analog
and stereo AES outputs. The ADMS 44.22 can be controlled through RS-232 serial
command. The ADMS 44.22 has four programmable relays and nine programmable
open collector outputs for controlling external device, and can transmit unit status
and GPI information to the controlling device for incorporation into broadcast
automation systems. 16x16 GPIO port; USB port, expansion port.
ADMS44.22 List $1,319.00
4x4 Active Stereo Matrix Switcher
The Broadcast Tools SS 4.4 provides matrix audio switching of 4 stereo inputs to 4
stereo outputs. Matrix switching allows any/or all inputs to be assigned to any/or
all outputs. The SS 4.4 may be controlled via front-panel switches, contact closures,
5-volt TTL/CMOS logic and/or the multi-drop RS-232 serial port. It provides a
headphone monitoring jack.
• Three switching modes: interlock, overlap and mix
• 4 open collector channel status outputs programmable via burst commands
• 4 SPST relay outputs via burst commands, and 16 input GPI port with LED
• Multi-turn input and output level controls
• Balanced stereo inputs/outputs;
depluggable screw (EURO) terminals
SS4.4
Contact BSW For Lowest Prices
See the video at
bswusa.com/SS16.4
List $529.00
Contact BSW For Lowest Prices
Superb Digital Audio Switcher
The Broadcast Tools AES Switcher Sentinel 4 is perfect for AES digital audio switching
via the web and/or local control. You can control and monitor it locally and/or
remotely over any IP network, including private networks, IP-based industrial control
networks, and the Internet. You can operate the AES Switcher Sentinel 4 using a web
browser, web-enabled mobile device, front panel switch and/or contact closures.
Email notification can be configured to alert up to eight recipients when alarms are
detected.
AES-SWITCHER List $299.00 Contact BSW For Lowest Prices
76
High Performance 2-Input, 10-Output Distribution Amp
The Broadcast Tools 2 x 10 DA stereo distribution amplifier is equipped with a
stereo line level high Z input, which accepts a balanced or unbalanced source with
ten active balanced low Z output amplifiers. Each output amplifier can be paired
for stereo or each output pair can be summed for monaural operation without
degrading the integrity of the other outputs. Each stereo output amplifier has a
front panel recessed level control.
2X10-DA List $239.00
Contact BSW For Lowest Prices
Depend
Price
match
on BSW
guarantee:
for the BSW
Best will
Selection
matchand
anyLowest
competitor’s
Prices advertised price
Call BSW For Your Best Price 1-800-426-8434
INTERFACE EQUIPMENT – ROUTERS
INTERFACE
ANDEQUIPMENT
SWITCHERS
To Interface
16X1
SS4.1III
SS8.1II
Versatile Passive Audio Switchers
Comprehensive Silence Monitor
The Silence Monitor III PLUS is designed to monitor any stereo or two independent
monaural sources, generate alarms and transparently switch to back-up source
equipment when silence is detected. Now with LED indicators for left/right audio,
audio and external alarms, power and more.
• Front-panel/remote control and relay monitoring
• Removable screw terminals
• Built-in stereo/monaural program switcher
• Precise time delay from 2 seconds to 93 minutes
• Precise restore timing delay from off to 46 minutes
• Relays for remote functions
• Selection of detection of -23, -25, -35 and -45 dB
25995
Broadcast Tools switchers offer local and remote control and status via contact
closures and RS232 serial ports.
The SS2.1BNCIII offers passive switching/routing with two composite audio or
AES/EBU inputs to two composite audio or AES/EBU outputs. Features: last selected
source memory; BNC connectors; 1/3-rack size. Optional RA-1 rack shelf.
SS2.1TERMIII/SS4.1PLUS offer passive switching/routing with two stereo inputs to
one stereo output or vice-versa (or four stereo inputs to one stereo output for the
SS4.1+). Pluggable screw terminal connectors; 1/3-rack size.
SS8.1II passively switches or routes any one of 8 stereo inputs to a single stereo
out. Features include front panel selection switches with LEDs; output muting and
remote step input; last source selected memory; 8-input GPI port; 1/2-rack size
mountable on optional rack shelf.
The 16X1 passively switches or routes any one of 16 stereo inputs to one stereo
output or vice-versa. Connections are via removable screw terminals.
SS2.1BNCIII
SS2.1TERMIII
SS4.1PLUS
SS8.1II
16X1
2x2 composite switcher
2x1 stereo switcher
4x1 stereo switcher
8x1 stereo switcher
16x1 stereo switcher
List $219.00
List $219.00
List $309.00
List $459.00
List $729.00
$
SMIIIPLUS List $299.00
Contact
BSW For
Lowest
Prices
Accessories: RA-1 rack mount shelf $53.99
Feature-Rich Digital
Monitor Switcher
4-In/16-Out Digital
i i l Audio
di System
The RDDA 4x4 is capable of distributing the same format AES and/or Word Clock
around your facility. Each input may be configured to feed any one or all of the four groups of
4 transformer-balanced outputs. Inputs, outputs and status are supplied on removable Euro
block connectors. Powered by a surge-protected internal power supply, its half-rack profile
lets it sit on a desktop, be mounted on a wall or rackmounted on the optional RA-1 rack shelf.
$
00
RDDA4X4
List $319.00
The Digital Monitor Switcher III is
designed to switch two AES signal
sources. It’s the digital answer to an analog silence
sensor/switcher.
il
/ it h FFeatures:
t
switch to backup source can be triggered by loss of clock, digital error flags,
external switch contact and/or the internal analog silence sensor; headphone jack,
balanced stereo monitor output; remote control; removable screw terminals.
DMSIII
List $509.00
Contact BSW For Lowest Prices
Accessories:
RA-1
Rackmount shelf
$53.99
329
Accessories:
RA-1
Rackmount shelf
$53.99
Dependable Digital Audio Switcher
Flexible Event Schedulerr
The new Schedule Sentinel is a webenabled event scheduler that can store
and control up to 100 unique events
using any available NTP timeserver as
a time base. It is equipped with two
independent serial ports.
The 3DRX AES digital audio switcher has two stereo digital and one stereo analog
input (on XLRs) plus a stereo digital output. The 3DRX will automatically switch to
the secondary digital input if the primary digital source fails (loss of lock, data error,
etc.) and then switch to analog input if the two digital streams fail. Features: 32 kHz,
44.1 kHz or 48 kHz sample rates; local, remote or automatic control; up to 24 bit, 96
kHz stereo digital audio for all digital inputs and outputs.
3DRX
3
List $1,250.00 Contact BSW For Lowest Prices
SCHEDULESENTINEL List $309.00
Contact BSW For Lowest Prices
Reliable, Straight
Forward Silence Monitor
The Broadcast Tools Silence Sentinel Basic
stereo silence sensor monitors any stereo
or two independent monaural sources and
generates alarms when silence is detected. It
may be set on a desktop, mounted on a wall
or optional RA-1 rack shelf for mounting up
to four units in 1-RU.
SILENCE-SENTINEL-BASIC List $169.00
Contact BSW For Lowest Prices
DB15 and DB37 Connectors
The Connect O' Adapter 15 MAX (COA-15MAX) plugs
into the male 15-pin D-Sub connector on the WW1 IDC
"MAX" or StarGuide II/III receivers, converting the DB-15
connector to the euroblock removable screw terminals.
The Connect O' Adapter 37 XDS (COA-37XDS) effectively
converts the male DB-37 connector to the removable
screw terminals on StarGuide II/III or ABC/CC XDS
receivers. The COA-9 XDS/MAX plugs into the male 9-pin
D-Sub connector on the ABC/XDS, WW1 IDC "MAX" or
StarGuide II / III.
COA15MAX
List $34.00 $27.95
COA37XDS
List $64.00 $53.99
COA9XDSMAX List $29.00 $25.97
1·800·426·8434
1·800·426·8434
• www.bswusa.com/interface
• www.bswusa.com • [email protected]
77
INTERFACE EQUIPMENT
Smooth, Transparent Balanced/Unbalanced Interfacing
The Henry Engineering Matchbox HD provides bi-directional stereo interfacing between unbalanced and balanced
audio. The TwinMatch interfaces two unbalanced consumer stereo outputs with professional balanced equipment.
• MATCHBOX HD:
Bi-directional stereo interface between -10 dBv
unbalanced and +4 dBu balanced
• True signal-to-noise ratio of 100 dB, with 22 dB
of headroom
• Total dynamic range of 122 dB
• Ideal for 24-bit sound cards and other digital
audio sources
• 4 independent amplifiers
• Built-in AC power supply, 1/3 rack width x 1RU
• Balanced XLR and unbalanced RCA I/O
• TWINMATCH:
Ideal for use with a pair of stereo CD players or
other "play only" sources
• Accepts 4 channels (2 stereo pairs) of -10 dBv
unbalanced audio and converts to professional
600 ohm balanced lines
• Adjustable gain to accommodate either +4 or
+8 dBm systems
• All circuitry is direct-coupled and transformerless for sonic transparency
• Unbalanced RCA inputs,
balanced XLR outputs
The Twinmatch is similar to the Matchbox, but provides unidirectional connection of two unbalanced stereo
signals to professional balanced systems. Signal/noise is >80 dB typical.
"Good, clean audio."
MATCHBOXHD Bi-directional interface amplifier List $225.00
TWINMATCH Unbalanced-to-balanced amplifier List $250.00
$179.00
$199.00
Accessories:
RMA
MATCHBOXHD Back Panel
MATCHBOXHD
$55.00
Rackmount kit for 1-3 units
TWINMATCH Back Panel
Multi-Format
M
Mu
ltii Formatt A
lt
Audio
udi
dio Interface
Interf
t face P
Panel
anell
The Henry Engineering MultiPort facilitates interface
between a studio and external audio equipment,
providing convenient access to a studio's analog
and digital audio inputs and outputs, and allowing
connection to both professional and consumer gear.
• Balanced/unbalanced analog stereo Line outputs
• 2 monaural balanced Mic outputs
• Accepts balanced or unbalanced analog
stereo Line inputs
• Transformer-isolated Digital I/O
• XLR, TRS, 3.5mm TRS and phono jacks
HENRY-MULTIPORT
List $495.00
Bi-Directional Interface
Amp w/ USB
Stereo Output Multiplier
The PatchBox II is a passive “output multiplier” that
can be used to distribute the output of a professional
audio mixer to the inputs of peripheral equipment.
It accepts both balanced and unbalanced sources.
From a stereo source, PatchBox creates twelve stereo
outputs: six balanced stereo and six unbalanced stereo
output pairs. PatchBox balanced outputs, on XLR and
1/4" TRS connectors, provide a “unity gain” signal with
a 600 ohm source impedance.
99
PATCHBOXII List $150.00 $
131
Contact BSW For Lowest Prices
See the video at
bswusa.com/MULTIPORT
The Henry Engineering USB Matchbox II is a professional
USB-to-XLR multi-mode stereo audio codec offering
superb audio performance with the ease of USB
connectivity. Ideal for any situation where computer
audio needs to interface with a professional analog
or digital audio system, it provides balanced analog
inputs and outputs, an AES/EBU digital output, plus a
headphone output for monitoring.
The heart of the USB Matchbox II is Burr Brown's new
generation phase coherent Delta Sigma 8X Oversampled
codec with SpAct audio clock recovery architecture.
The codec's superb performance is further enhanced
with proprietary L/C pre-filtering and analog circuitry,
fine-tuned to eliminate the transient intermodulation
products that plague the typical sound card. Front panel
trimmers allow precise adjustment of input and output
levels. Connections include XLRs and the AES/EBU digital
output. A headphone output is included.
USBMATCHBOXII
List $550.00
Contact BSW For Lowest Prices
3-Input
3
Input Stereo Audio Switcher
The Henry StereoSwitch II is a handy 3-input audio
switcher for remotely selecting between three stereo
sources. It features front panel pushbuttons for
local control, plus remote control via GPI. With no
circuitry in the audio path, it offers transparent source
selection. It can also be used in reverse, as a router, to
send a source to one of three destinations.
99
STEREOSWITCHII
List $295.00 $
251
Failsafe
F
il f AC Power
P
Switcher
S i h
The Henry Engineering PowerSwitch is an automatic
AC power controller that can be used to switch AC
power between Main and Backup devices, or to simply
turn AC power on or off. It provides an audible alarm,
as well as remote status indication.
99
POWERSWITCH
List $250.00 $
Rackmount kit for 1-3 units
Rackmount kit for 1-3 units
$55.00
213
RMA
$55.00
Multi-Purpose Audio Switcher
This multi-purpose stereo audio switcher and silence sensor
can be used to manually or automatically select between
two stereo audio sources. It also features an Alarm relay output,
ut,
plug in euroblock connectors and a built-in power supply.
99
AUTOSWITCH List $295.00 $
251
RMA
Accessories:
Accessories:
RMA
Accessories:
Rackmount kit for 1-3 units
$55.00
Flexible
Fl
ibl Control
C
l Interface
I
f
The Henry Logiconverter is a general-purpose control
interface that eliminates the incompatibility between
various audio and video equipment remote control
circuits. It has 4 opto-isolated inputs that control 4
isolated relay outputs and can be programmed to
provide either latched or momentary outputs with up
to 24 combinations. Inputs can provide single or dual
flip-flop outputs.
99
$
LOGICONVERT List $250.00
1·800·426·8434
1·800·426·8434
• www.bswusa.com/interface
• www.bswusa.com • [email protected]
213
79
INTERFACE EQUIPMENT
"Reliable."
No-Nonsense Passive
Direct Box
MB15B
Passive doesn't mean wimpy. Built rugged
on the inside and outside, you'll find this
direct box in pro systems everywhere.
It converts a line or instrument level
unbalanced signal to a low impedance mic
level balanced signal quickly, efficiently and
quietly. Features: 1/4" parallel wired in/out jacks, Ground Lift switch to help isolate
hum and buzz, impedance ratio (input to output): 133:1.
$
95
IMP2
List $47.82
44
Level Matcher with Dual
XLR and Stereo RCA I/O
The Rolls MB15 ProMatch converts
consumer level stereo RCA signals to
balanced XLR professional line level, and back. One side of the unit has two XLR
inputs and stereo RCA outputs. The other side has stereo RCA inputs and
two XLR outputs. Each side has stereo level controls.
$
95
MB15B List $90.00
64
Kills Buzz Dead
Handy 8-Channel Transformer/Isolator
ART’s Transformer Eight is a totally passive audio interface that uses eight
transformers to separate input and output signal grounds, thereby isolating two
systems and reducing hum and ground-loop noise. Balanced XLR, 1/4" phone, and
RCA type phono connections on all inputs and outputs simultaneously. Perfect as
an interface between your DAW and your monitor system, isolation on long cable
runs, etc.
00
$
T8
List $189.00
The 2-channel Rolls Buzz Off
eliminates virtually all ground hum
and buzz by simply inserting it into
the audio path. It also will convert
an unbalanced signal into a balanced
signal (and vice-versa). $
00
BUZZOFF
59
149
Easiest Way to Get Rid of
Ground Hum
The Ebtech Hum X filters out unwanted voltage and
current in the ground line that cause ground loop hum
while simultaneously maintaining a solid, safe ground.
Simply place the Hum X on the end of the power cord
of the equipment that has a Ground Loop and plug the
Hum X into the wall outlet.
HUMX List $105.00
The Philmore ST-200 is a step-up or step-down AC
transformer (110V AC to 220V AC or 220V AC to
110V AC) with a maximum wattage of 200 watts.
38
$
ST-200
44
$
7199
Eliminate Hum
E
T Ebtech Eliminator HE2 (2-channel model)
The
eeliminates 60 Hz cycle hum caused by ground loops
aand also converts back and forth between balanced
aand unbalanced signals at either end. It sports
balanced XLR and 1/4" TRS I/O.
b
$
99
HE2XLR List $125.00
H
Versatile AC Transformer
85
Oh yeah? Well
maybe THIS
will get rid of
your incessant
humming!
ACCESSORIES
Low Tack Console Tape
Knowing who's who while recording them is always a good
thing. So is not having ugly residue on your channel strips.
This is what you need. Low tack. Bright white. Write on it,
and peel it off with no side-effects when you're done. White,
1" wide.
$
99
CONSOLETAPE
14
Gaffer’s Tape in Assorted Colors
On every gaffer's wish List high quality 2-inch wide tape in
a 180-foot roll. Available in white, black and yellow.
GFT-447WH White $19.95
GFT-447BK Black $19.95
GFT-447YE Yellow $19.95
Handy Cable Testers
With the Whirlwind Qbox, you can
send a tone or signal over any XLR
line. This battery-powered unit has
a mic, speaker, test tone generator,
headphone jack, a 1/4" jack for line
in and LEDs for confirming phantom
power. The Tester provides cable
testing with XLR, 1/4" and phono
plugs.
QBOX
List $199.94 $181.99
TESTER
List $71.94
$68.00
80
Depend on BSW for the Best Selection and Lowest Prices
INTERFACE EQUIPMENT
INTERFACE EQUIPMENT - DISTRIBUTION
AMPLIFIERS
"Gets the job done well!"
Summing
Distribution Amp
D
T U.S.D.A. can be used as a 1X4
The
oor 2X4 DA, or to combine a stereo
input to a mono output. Two inputs
in
(one stereo pair) accept balanced/
(o
uunbalanced sources; four 600 ohm
balanced outs (two stereo pairs);
b
mono/stereo switches; euroblocks.
m
99
USDA
U
List $250.00 $
213
Accessories:
RMA
Rackmount kit for 1-3 units
$55.00
DA1600
2x8 or 1x16 Distribution Amplifier
A top seller at BSW, the Radix DA1600 is a heavy-duty distribution amp with 8 stereo
or 16 mono balanced outputs. Level control and selectable pads accommodate a
wide range of input levels. Features: removable, plug-in connectors that allow wiring
changes to be made quickly and effortlessly with the distribution amp still in the
rack; THD .01% max @ +20 dBm out, SNR 90 dB.
$
00
DA1600
List $520.00
369
AES/EBU-to-S/PDIF
Distribution Amp
T Digimatch 2x6 is an AES/EBUThe
to-S/PDIF interface and distribution
to
aamp for digital audio signals. It has
oone AES/EBU input and three AES/
EEBU outputs, plus one S/PDIF input
aand three S/PDIF outs.
DIGIMATCH2X6 List $395.00
D
Contact BSW For Lowest Prices
Accessories:
RMA
Rackmount kit for 1-3 units
Affordable 2x4 or 1x8 Distribution Amp
The Rolls RA63S is an eight-channel mono, or four-channel stereo distribution
amplifier designed for the contractor / install market. The outputs are designed to drive
high-level balanced lines in a sound distribution system. The screw terminals on the
rear panel are for input and output, and each output may power more than one line.
$
95
RA63S
144
List $188.00
$55.00
2x16
2
16 Distribution
Di t ib ti A
Amplifier
lifi
Affordable, Dependable Stereo Distribution Amp
The Broadcast Tools 2x6 DA boasts a stereo line level high-Z input (accepts a
balanced or unbalanced source) and six active balanced low-Z output amplifiers
with individual level control.
95
2X6DA List $209.00 $
179
The Rane DA216S is a 2-input, 16-output splitter/distribution amplifier, capable of
providing 16 discrete balanced outputs from one or two balanced mic level or line
level inputs. The level of each output is individually adjusted via one of the sixteen
level controls. Each output may be assigned to either or both inputs via accessible
slide switches. The Master A and B Level controls affect the overall level of each
input. LEDs indicate an overload at either the inputs or at the internal gain stages.
Input gain switches provide a mic input with +60 or +40 dB of gain, or a line input
with +20 or 0 dB. Euroblock connectors, and an internal universal power supply.
DA216S
List $549.00
Contact BSW For Lowest Prices
Active Balanced Outputs
High Performance Distribution Amp
The Aphex 120A is a high-performance 1x4 audio distribution amp. It features one
high impedance input and four low impedance outputs, all electronically servobalanced; half-rack steel chassis; THD < .002% @ +4 dBm; hum and noise better than
90 dB down.
120A List $399.00
Contact BSW For Lowest Prices
The DA208 is a dual 1x4 DA and the DA416 is a quad 1x4 DA. Features: outputs
are active balanced and individually adjustable; inputs can be paralleled on rear
connectors for 1x8, 2x8 or 1x16 operation; barrier block input and
output connectors. The DA208 and DA416 have clipping indicators. The DA208S
version adds signal-present indicators to the DA208.
DA208 Dual 1x4 dist. amp barrier I/O, clipping indicators
DA208S Dual 1x4 dist. amp barrier I/O, signal indicators
DA416 Quad 1x4 distribution amp barrier I/O
List $569.00
List $589.00
List $789.00
Contact BSW For Lowest Prices
Full-Featured Digital Distribution
Distributiion Amp
Amp
XLR Inputs and Outputs
The Rolls RA163 eight-channel mono, or four-channel stereo distribution amplifier
designed for the contractor/install market. The outputs are designed to drive highlevel balanced lines in a sound distribution system. The XLR jacks on the rear panel are
for input and output, and each output may power more than one line.
00
RA163
List $200.00 $
159
The ATI DDA-212XLR distributes digital audio (AES3) at up to 192kHz sample rates
with incredibly low jitter and ultra-short propagation delay. Switchable inputs
(2 Input 1X12 or Dual 1X6, XLR I/O) let you choose from multiple input streams.
Selectable re-clocking lets you precisely regenerate a pristine input signal or handle
Surround-encoded audio. Sample Rate, Word Length, Fault Diagnostic and Pro/
Consumer displays tell you your audio is clean or let you know why it's not. Pushbutton Input EQ optimizes for long input cables.
DDA212XLR
List $1,399.00
Contact BSW For Lowest Prices
1·800·426·8434
BSW
1·800·426·8434
is always
• www.bswusa.com/interface
there,
• www.bswusa.com
always working…Always
• [email protected]
ON.
81
INTERFACE EQUIPMENT
Whatever the Job
Web-Based Silence Monitor
This web based dual channel stereo silence monitor
monitors two independent stereo analog audio
sources and switches to a back-up analog audio
source when silence is detected. The Audio Sentinel
can be controlled and/or visually monitored over the
Internet using a web browser. Email alarms may be
generated.
95
AUDIOSENTINEL
List $299.00 $
259
"Very useful product."
See the video at
bswusa.com/
AUDIOSENTINEL
Full-Featured
Status Monitor
4-Input Stereo
Utility Mixer
The SUM-4 features
four line level high-Z
inputs, which accept
a balanced or
unbalanced source; stereo and monaural balanced
low-Z outputs; individual level controls; stereo
mixing/link port for input expansion.
95
SUM4 List $209.00 $
179
AUDIOSENTINEL
Ultra-Compact
Serial Remote
Controls
The tinyTOOLS
SRC-2 interfaces two
optically isolated inputss
and two SPST relays to a RS-232
or USB port. It can notify
fyy a PC software
program that any of two
woo inputs have been
opened or closed and allows
your software to control two SPST, 1-amp relays.
The SRC-2X interfaces via Ethernet.
SRC2 List $149.00 $129.95
SRC2X List $219.00 $189.95
DTMF Tone
Encoder/
Decoder
The tinyTOOLS
DTE16 by Broadcast Tools is a feature-rich DTMF tone/
sequence encoder that is programmable to encode
up to four tone sequences or a single tone via any one
of 16 contact closure inputs and/or the RS-232 serial
port. The DTD16 is a DTMF decoder.
DTE16 DTMF encoder List $209.00
$179.95
DTD16 DTMF decoder List $209.00
$179.95
The Status Sentinel is
a robust, full-featured
Ethernet based data
acquisition device
with three optically isolated
l
lated
status (digital) inputs. Itt may
be monitored over any IP network
including private networks,
k IP-based
IP b d
industrial control networks, and the Internet using
web browser or web-enabled mobile device, while
email notification may be configured to alert up to
four recipients when alarms are detected. The user
may also enable a sound effect to play when an alarm
is generated. Logging of input status, along with the
site ID may be emailed from once an hour to once a
day. The Status Sentinel 16 gives you 16 status inputs.
STATUSSENTINEL
List $179.00
$156.95
STATUSSENTINEL16
List 209.00
$189.95
Auto Answer C
Coupler
l
4 GPS TimeReferenced
Outputs
The Time Sync Plus
provides four GPS
time referenced outputs.
s. The
first is an SPST relay, which
ch pulses
at 12:00, 22:00, 42:00, and
nd 54:30 and is
user-programmable in each of four locations for any
minute and second. The second is an active high driver
with a 100 ms pulse each second, while the third is a
4800-baud, RS-232 serial port providing a time zone
adjustable time code. The fourth provides an active
high driver in the ESE TC-90 serial time code format.
TIMESYNCPLUS
List $409.00
Contact BSW For Lowest Prices
Relay Sentinel
For many applications,,
the Relay Sentinel
is the easiest and
least expensive way
to remotely control
equipment over the Internet
nteernet
using a web browser. It has
three low-signal SPDT re
relays
elays that can
individually switch up too 1 Amp at 28V. Each
relay can be turned on, off, pulsed or timed latched
using the built in web pages. In addition, each relay
can be configured to open and close remotely when
used with the Status Sentinel. The Relay Sentinel 16
gives you 16 relay inputs.
RELAYSENTINEL
List $179.00
$154.95
RELAYSENTINEL16
List 209.00
$186.95
tinyTOOLS Rack Shelf
T RA-1 fits up to four tinyTool products. It comes
The
supplied with filler panels and mounting hardware.
99
RA-1
tinyTools rack shelf
List $59.00 $
53
Easy Conversion
Need to convert a DB-15
connector to euroblock
removable screw terminals?
The Broadcast Tools
Connect O' Adapter 15 MAX
will do the job. It is specially
designed to plug into the
male 15-pin D-Sub connector on th
the WW1 IDC
"MAX" or StarGuide II/III.
$
95
COA15MAX List $34.00
124
Reliable,
Straightforward
Silence Monitor
The Broadcast Tools
Silence Sentinel Basic stereoo
silence sensor monitors anyy stereo or
two independent monaural
al sources and
generates alarms when silence
detected. It may
ennce is detected
be set on a desktop, mounted on a wall or optional
RA-1 rack shelf for mounting up to four units in 1-RU.
SILENCE-SENTINEL-BASIC
List $179.00
14995
$
27
Flexible Circuit
Switcher
Interfaces 16 GPII
to Serial/USB Port
rtt
The Broadcast Tools LR-5 is a
mechanical latching relay with
one set of four-pole double throw
contacts and one set of singlepole normally open contacts. It can switch all types of audio,
audio
AES and AC/DC circuits. It also features a five-volt DC 100ma
power supply to power external equipment, removable
euroblock screw terminals and LED indicators to display
power and relay ON.
$
95
The Broadcast Tools GPI16 interfaces 16 generalpurpose logic inputs to
your PC COM or USB port,t,
and lets you select from two
w prewo
programmed serial formats.
atss. The GPI
GPI-16
16
is supplied with a Smart USB
SB to RS-232 adapter
cable, DB-9 male-female straight-through serial
cable and 7.5 VDC @ 800 ma wall power supply.
$
95
LR-5 List $65.00
82
The TT-1 is a compact auto-answer and autodisconnect telephone hybrid. A multi-turn hybrid
NULL trimmer achieves 20+ dB separation. The rear
panel is equipped with a RJ-11 jack for the telephone
line. A minijack (3.5mm) and screw terminals are
provided for balanced send and caller audio.
95
TT1 List $149.00 $
54
GPI-16
List $144.00
Depend on BSW for the Best Selection and Lowest Prices
123
INTERFACE EQUIPMENT
BSW's Got the Tools!
Actual Size
RDL STICK-ON Series Audio Interfaces
Radio Design Labs Stick-Ons are compact, high-quality audio interface devices that can be directly and discreetly mounted on equipment, under counter tops, or
combined in rackmount systems. Active units require a 24-volt power supply such as the PS24A (sold separately). Go to bswusa.com for more detailed information and
additional models not shown here.
$141.95
STM2
Microphone preamplifier
List $185.52
$144.99
STDA3
1x3 line level distribution amp
List $181.84
STMDA3 1x3 mic level distribution amp
List $177.65
$107.97
STPA2
2-watt utility power amplifier
List $89.53
$74.99
STD10K 10K ohm divider/combiner
List $72.24
$60.95
STPA6
6-watt utility power amplifier
List $124.96
$103.95
STD150 150 ohm divider/combiner
List $72.24
$60.95
STGCA3 Audio gain control amplifier
List $164.78
$128.95
STD600 600 ohm divider/combiner
List $72.24
$60.95
STP1
Dual attenuator (passive)
List $78.55
$65.99
STRX2
1x2 audio routing switcher
List $136.54
$113.95
STVP1
Voice-over module
List $177.13
$137.97
STSX4
4x1 audio switcher
List $132.63
$109.99
STPH1
Stereo phone preamp
List $176.43
$137.97
STMX2
2-channel mic/line mixer
List $175.86
$137.97
STACR2 Audio control relay
List $127.53
$105.95
STMX3
Line level mixer
List $162.18
$134.99
STLCR1 Non-latch logic control relay
List $98.39
$81.99
STA1
Interface amplifier
List $191.38
$149.99
Accessories:
STA1M
Audio line amplifier
List $140.76
$116.99
STR19A 12-unit rackmount kit
List $172.94
$134.99
STA2A
Line amplifier
List $202.10
$157.97
STPD5
Power 5 units from one supply
List $89.01
$73.99
STUBA2 2 ch. unbal to bal convertor
List $197.63
$153.95
PS24AS Power supply
List $28.87
$28.17
Silence Monitors
The DM Engineering Silence Sense Jr. features
adjustable silence detect time duration with switchselectable momentary or continuous relay contact
closure output. It can be installed at studio or
transmitter locations and interfaced with auto-dialing
remote controls for instant notification of studio, STL,
or phone line audio failures. The Silence Sense Sr.
adds a pager-dialer module for more alert options.
SILENCESENSEJR List $109.00 $109.00
SILENCESENSESR List $229.00 $229.00
SILENCESENSEJR
Dual Channel
Audio Meter
The RU-SM16 offers precise audio level
metering. Features: 16 segment display
for 2 audio channels; selectable peak
or average metering; peak L+R/L-R
metering; 1/3 rack width.
$
95
RUSM16
List $300.73
Balanced Audio Switch
The Radio Design Labs RU-SX4 is a mono 4x1 audio switcher for either local or
remote control. It features 4 line level bridging inputs to a single line level output;
front panel multi-turn trims; solid state audio switching; multiple switching control
points; remote source selection via normally open momentary switch; front-panel
LED indicators show selected source.
$
95
RUSX4A
List $348.32
236
233
2x4 Stereo, 1x8 Mono
Distribution Amplifier
The Radio Design Labs RU-ADA4D is a four
channel stereo audio distribution amplifier
with input and output gain adjustments
and input level metering. The module may
be operated in mono to provide up to
eight distributed mono signals.
RUADA4D List $320.78 Contact BSW For Lowest Prices
4-Channell Mi
Mic/Line
/Li Mi
Mixer
This compact, 4-channel mixer from Radio Design Labs is only 1/3 rack space wide.
Features: four balanced/unbalanced main inputs (4-mic/line via XLR or RCA); a mix
input for combining multiple mixers; balanced mic or line output, plus unbalanced
line output; LED VU meter; 24V phantom power for each mic input; built-in
switchable soft-knee compressor.
99
$
RUMX4
List $416.10
297
1·800·426·8434
1·800·426·8434
• www.bswusa.com/interface
• www.bswusa.com • [email protected]
83
INTERFACE EQUIPMENT
StudioHub+ Broadcast
Here is a small listing of some of the
most popular StudioHub+ Items
StudioHub+ from Radio Systems is designed
to be the broadcast industry's first prewired
cabling system for digital ready operation.
With CAT-5 rated shielded twisted pair
cables, StudioHub+ efficiently routes both
analog and digital signals throughout a
facility. StudioHub+ features pre-made
source cables for all types of studio gear
and quick-connect blocks and peripheral
amplifiers to easily harness all studio gear
together. On-site wiring time is dramatically
reduced due to the true plug and play nature
of StudioHub+. Every system component
quick connects with RJ-45 jacks, and all
peripheral products are phantom powered
with the built in DC-link system.
SHHP
SHMIC
SHTALENT
SHGUEST
MJIN
MJOUT
MJSPDIFIN
MJSPDIFOUT
PSWWSH
PSEXTU
PSCUBE
PSWWCUBE
SH1BUT
SH2BUT
SH3BUT
PATCH48
HUB12
HUB16DC
MJAD
MJDA
Headphone Amp
Mic Pre Amp
Talent Panel
Guest Panel
Matchjack Input
Matchjack Output
AES/EBU to S/PDIF Converter
S/PDIF to AES/EBU Converter
AC Wall Adapter Supply
External Power Supply
Power Supply Cube Power Inserter
Power Supply for PS-CUBE
Push Button Panels
Push Button Panels
Push Button Panels
48 Channel Patch Panel
12 Channel Break out Box for ASI Cards
16 Channel RJ-45 Hub
A to D AES/EBU Converter
D to A AES/EBU Converter
List $95.00
List $80.00
List $322.00
List $169.00
List $75.00
List $75.00
List $85.00
List $85.00
List $20.00
List $295.00
List $65.00
List $20.00
List $75.00
List $110.00
List $145.00
List $695.00
List $195.00
List $295.00
List $145.00
List $145.00
$86.99
$75.00
$289.99
$152.99
$69.00
$69.00
$79.00
$79.00
$20.00
$269.00
$59.00
$20.00
$69.00
$99.00
$130.99
$629.00
$179.00
$265.00
$145.00
$145.00
HUB32
Complete Console Kits
These convenient and economically priced console kits boast all the CAT-5 cable
and adapters you'll need for a large (18-channel), medium (12-channel) or small
(6-channel) analog or digital console.
Connect
ct With Hubs
• Male and Female XLR adapters
• TRS and pigtail adapters
• CAT-5 shielded patch cords in various lengths
CONSOLE-KITSM
CONSOLE-KITMD
CONSOLE-KITLG
Console Kit Small
Console Kit Medium
Console Kit Large
StudioHub + has a wide range of hubs to provide connectivity for a wide range of
gear. Below is just a sample of what we carry. Vist our website for more!
List $295.00
List $375.00
List $495.00
$269.00
$349.00
$449.00
HUB12
HUB24
HUB32
HUB8DC
HUBRIO
12-channel Breakout Box
24-channel Loop-thru Hub
32-channel Mini Amp Hub
8-channel RJ-45 w/ DC Link
32-channel Breakout for SAS RIO
BSW stocks StudioHub+ patch cords and adapters! See us on the web: www.bswusa.com
84
List $195.00
List $335.00
List $375.00
List $195.00
List $339.23
$179.00
$299.00
$339.00
$179.00
Contact BSW For Lowest Prices
Depend on BSW for the Best Selection and Lowest Prices
INTERFACE EQUIPMENT
Interconnect Made Simple
Shielded RJ-45 Patch Cords
All StudioHub+ cabling is shielded and CAT-5 certified. Choose from a wide
range of lengths of RJ-45 patch cords for all StudioHub+ connections.
ADAPTRCA
ADAPTTRS
ADAPTM-XLRF
ADAPTBO
ADAPTXLRM
ADAPTPIGTAIL
StudioHub + Adapters For Every Need
Use these female adapters in combination with any length of RJ-45 to RJ-45
patch cables to create connector/cable combination of any length.
ADAPTXLRF
RJ-45 Female to XLR Female – 8-inch
$16.00
ADAPTXLRM
RJ-45 Female to XLR Male – 8-inch
$16.00
ADAPTTRS
RJ-45 Female to 1/4" TRS – 8-inch
$16.00
ADAPTM-RCAM
RJ-45 Female to RCA – 8-inch
$20.00
ADAPTPIGTAIL
RJ-45 Female to Pigtail – 8-inch
$12.00
ADAPTRCA
RJ-45 Female to RCA Male – 8-inch
$16.00
ADAPT-MINI
RJ-45 Female to 1/8" - 8-inch
$16.00
ADAPT-MINIUNBAL RJ-45 Female to 1/8" - 8-inch
$16.00
ADAPT-TA3
RJ-45 Female to TA3 XLR Female- 8-inch
$16.00
These RJ-45 Male 6-foot adapters are designed for use with Axia Nodes,
Wheatstone Blades, Radio Systems' Platform and Logitek JetStream
audio engines.
ADAPTM-XLRF
RJ-45 Male to XLR Female – 6-ft.
$20.00
ADAPTM-XLRM
RJ-45 Male to XLR Male – 6-ft.
$20.00
ADAPTM-TRS
RJ-45 Male to 1/4" TRS – 6-ft.
$20.00
ADAPT-PUNCH
RJ-45 Male to Bare End – 10-ft.
$12.00
ADAPTM-MINI
RJ-45 Male to 1/8" – 6-ft.
$20.00
PATCH1
PATCH2
PATCH3
PATCH5
PATCH7
PATCH10
PATCH12
PATCH15
PATCH20
PATCH25
PATCH25
PATCH25
PATCH25
PATCH125
PATCHKITLG
PATCHKITMN
1-ft.
$3.00
2-ft.
$3.00
3-ft.
$3.00
$4.00
5-ft.
$4.00
7-ft.
$5.00
10-ft.
12-ft.
$7.00
15-ft.
$7.00
20-ft.
$7.00
$8.00
25-ft.
$8.00
35-ft.
50-ft.
$8.00
$8.00
100-ft.
$40.00
125-ft.
Large Patch Cable Kit with 75 Cables
Mini Patch Cable Kit with 20 Cables
High Performance Patch Panels and Switchers
RJ-45 equipped patch panels and program material switchers provide StudioHub+
connectivity and flexibility along the entire program chain
SH1-4UNBAL
TRS 1/4" & Mini Panel (Unbalanced)
$49.95
SH1BUT
1-Push Button Panel
$69.00
SH2BUT
2-Push Button Panel
$99.00
SH2BUTRJ
2-Push Button Panel with RJ-45 connector
$119.00
SH2XLRF
Dual XLR Female Panel
$45.99
SH2XLRM
Dual XLR Male Panel
$45.99
$SH2XLRMF
Dual XLR Male-Female Panel
$45.99
$135.00
$SH3BUTRJ
3-Push Button Panel with RJ-45 connector
SH4SW
4 Source Switch Panel
$131.99
SHAESSPLIT
AES/EBU 2-Way Splitter
$69.00
SHAMPSPKR
8-Watt Monitor Amp Panel with Speaker
$179.00
$8.00
SHBLANK
Blank Filler Panel
SHGUEST
Dual-Surface (Headphone, XLR) Guest Panel $152.99
SX2XLRF
SHHP
Headphone Amp
$86.99
SH-HPDUAL
Dual Headphone Amp
List $145.00 Contact BSW For
SH-MATCHPANEL Match Panel
List $125.00 Lowest Prices
These adapters are designed for specialized applications.
ADAPT-SUM
ADAPTMONO
ADAPTST
ADAPTBO
ADAPT-BTL
ADAPT-BTU
ADAPT-GPI
ADAPT-KITAIR3
ADAPTKITLG
ADAPTKITMD
ADAPTKITMN
ATTENXXDB
In-line summing adapter
In-line mono adapter
Stereo Tee splitter adapter
RJ-45 Breakout Adapter to Screw Terminals
Broadcast Tools Lower Adapter
Dual RJ-45 Breakout Adapter to Push Terminals
Dual RJ-45 Breakout Adapter to Push Terminals
Adapter Kit for Air 3 Console
Large 80 Adapter Kit
Medium 60 Adapter Kit
Mini 20 Adapter Kit
In-Line Attenuator
$20.00
$20.00
$25.00
$48.00
$25.00
$25.00
$48.00
$575.00
$999.00
$749.00
$249.00
$20.00
$
$359.00
$109.00
PSCUBE
Power Up With StudioHub+
StudioHub+ power supplies provide "DC-Link" power
distribution to hubs for active panels and matchjacks.
They can also power active hubs,use wall adapters directlyy
or with cables to power panels and matchjacks independently.
entlly.
y
PSCUBE
PSEXTU
PSWWCUBE
PSWWSH
PS-WWUSH
Power Supply Cube Power Inserter
External Power Supply
Power Supply for PSCUBE
AC Wall Adapter Supply
AC Wall Adapter Power Supply for Active SH+ Panels
$59.00
$269.00
$20.00
$20.00
$20.00
Convenient Under-Table Mount
Handy Cables/Connectors
Keep your desktop clear with this StudioHub + under-tablee
moon mount (headphone amp shown not included).
SHMOON
$77.99
Get the exact connection you need with StudioHub+ cables and connectors.
RJ21AD16-010
Cable RJ21M To AMP 2 Pin
$215.38
RJ21-AXIAGPI-010 Axia GPI Cable
$95.00
RJ21RIO-010
Cable Cat5 RJ21X SAS Rio
$129.23
Mounts For Every Need
RJ21TIE-050
Here is a wide selection of mounts for any StudioHub+ panels for desktop, under
counter, surface or consolette style installation.
SHRACK4
4 Position Rack Mount
$25.00
SHSURF1
Single Surface Mount
$28.00
SHSURF2
Dual Surface Mount
$8.00
SHTALENT
Triple Surface Panel
$289.99
SHWELL1
Single Well Mount
$20.00
SHWELL2
Dual Well Mount
$22.50
SHWELL3
Triple Well Mount
$25.00
EUROAN32-0101
12676
18596
MINITIE244
OUTPUT-KITLO
CAT-5 25 Pair Tie Line Cable w/
RJ21X Connectors Both Ends, 50FT
Cable Euro F To 2 Pin Amp
SH+ Type CP Dongle
CN Dongle For Content Depot
RJ-21 to 24 4-Wire RJ-45's
IP Kit For Logitek Output Cards
1·800·426·8434
1·800·426·8434
• www.bswusa.com/interface
• www.bswusa.com • [email protected]
$143.27
$140.00
$25.00
$25.00
$225.00
$78.00
85
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement