Digital Watchdog DWC-PV2M4T Panoramic Camera User's Manual
Below you will find brief information for Panoramic Camera DWC-PV2M4T. The MEGApix Panoramic 2.1MP 180° Camera DWC-PV2M4T offers a wide field of view with 2.1MP resolution and 180° panoramic lens, also, you can adjust the camera's panning angle and tighten the hard lock set screw on the camera's dome to achieve optimal security coverage.
Advertisement
Advertisement
MEGApix® Panoramic
2.1MP 180° Camera
DWC-PV2M4T
User’s Manual
Ver. 1.0 / 2015.04.21
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Warning
This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
Precaution
This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING
To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.
WARNING
1.
Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product.
2.
Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to the product.
3.
Do not connect multiple cameras to a single adapter.
Exceeding the capacity may cause excessive heat generation or fire.
4.
Securely plug the power cord into the power receptacle.
Insecure connection may cause fire.
5.
When installing the camera, fasten it securely and firmly.
A falling camera may cause personal injury.
6.
Do not place conductive objects (e.g. screw drivers, coins, metal items, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.
7.
Do not install the unit in humid, dusty, or sooty locations.
Doing so may cause fire or electric shock.
8.
If any unusual smells or smoke come from the unit, stop using the product. Immediately disconnect the power sorce and contact the service center. Continued use in such a condition may cause fire or electric shock.
9.
If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way.
10.
When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.
Precaution
Operating
• Before using, make sure power supply and all other parts are properly connected.
• While operating, if any abnormal condition or malfunction is observed, stop using the camera immediately and contact your dealer.
Handling
• Do not disassemble or tamper with parts inside the camera.
• Do not drop the camera or subject it to shock or vibration as this can damage the camera.
• Clean the clear dome cover with extra care. Scratches and dust can ruin the quality of the camera image.
Installation and Storage
• Do not install the camera in areas of extreme temperature,
exceeding the allowed range.
• Avoid installing in humid or dusty environments.
• Avoid installing in places where radiation is present.
• Avoid installing in places where there are strong magnetic fields and electric signals.
• Avoid installing in places where the camera would be subject to strong vibrations.
• Never expose the camera to rain or water.
1
Important Safety Instructions
1.
Read these instructions. - All these safety and operating instructions should be read before the product is installed or operated.
2.
Keep these instructions. - The safety, operating and use instructions should be retained for future reference.
3.
Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.
4.
Follow all instructions. - All operating and use instructions should be followed.
5.
Do not use this device near water. - For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement; near a swimming pool; etc.
6.
Clean only with dry cloth. - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.
7.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. - Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product, and to protect it from over-heating. The openings should never be blocked by placing the product on bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer’s unstructions have been adhere to.
8.
Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11.
Only use attachments/accessories specified by the manufacturer.
12.
Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13.
Unplug this apparatus during lightning storms or when unused for long periods of time.
14.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
2
Disposal of Old Appliances
1. When this crossed-out wheel bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately form the municipal waste stream stream in accordance to laws designated by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.
waste disposal service or the shop where you purchased the product.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interferenece at his own expense.
3
Introduction -
Product & Accessories
Please check that all the following accessories are included in the package.
Camera Cables
Quick Manual Manual CD Template Sheet Test Monitor Cable
Screw & Plastic Anchor-4pcs T-Wrench Torx Wrench Six angles Wrench
4
Introduction -
Product & Accessories
Tilt,Rotation Control
Main Body
Cables
¾” Pipe Mounting Hole
Mount Braket
reset
3 Panoramic Lens
OSD Cap
Reset Button
SD card Slot
Hard Lock Set Screw
5
Istallation -
Disassemble the Camera
Before installing your camera, you have to read the following cautions.
2. Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise
3. When installing your camera, don’t allow any person to approach the installation site. If you have any valuable things under the place, move them away.
1 Disassemble the camera
Loosen a small hard lock set screw on the Mount Braket using a small six angles wrench to disassemble the camera from a Mount Braket to for installation.
Warning:
Never Open the Dome.
Supplier will not take any responsibility on any defection from an arbitraty disassembly.
6
Installation -
Mounting the Camera
Template Sheet
2
1 Disassemble the camera, See the section ‘Disassemble the camera’ for details.
2 Using the template sheet, make the cabling holes on the wall/ceiling.
3 Fix the Mount braket on the wall/ceiling by screw provided.
4 Hook the Main body to Mount braket with safety wire.
5 Bring the cables into the Mount braket through the hole.
3
Safety Wire
Mount Braket Hole
5
4
6
7
6
Connect the cables respectively. See the section
‘Cabling ’ for details.
7 After connecting the cables, main body to be assembled into the Mount bracket.
8 Detach the protection film from the Dome Cover.
9 Adjust the panning angle of the camera and tighten the hard lock set screw on the camera's Dome. See next page for more information.
8
7
Installation -
Adjusting the Camera's Pan and Tilt
6
7
8
9
9
*
Warning:
The panoramic outdoor dome camera can rotate 360° at each direction. Rotating the camera constantly to the same direction may harm the internal rotation mechanism and cause the camera's rotation harness to snap.
Installation -
Inserting / Removing the SD Memory Card
The memory card is an external data storage device that has to record and share video, audio, and text data using digital devices.
Micro
(Not Included)
- Type: Micro SD (SDHC)
- Manufacturer: Transcend, Kingston, Toshiba, Sanddisk
- Capacity: 4~16G
- Class: over Class 6
1 Insert the SD card in the arrow direction.
Do not insert the SD memory card while it’s upside down by force. Otherwise, it may damage the SD memory card.
2 Removing an SD Memory Card Gently press down on the
Remove the SD Memory Card gently by pressing down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot.
Pressing too hard on the SD memory card may cause the card to shoot out uncontrollably from the slot when released.
If you have saved data in the SD memory card, removing the SD memory card prior to setting record to OFF will cause damage to the data stored in the card.
9
Installation -
Cabling
White : DIN+
Yellow : DIN-
Black : DOUT-
Red : DOUT+
4 Alarm In
1 Audio Out
2 Audio In
3 Alarm Out
1 Audio In
Connect an ‘Audio In’ device such as a microphone to the camera’s input cable and GND pin of the cable slot. Audio input device is activated and conÿgured from teh camera’s web-viewer.
2 Audio Out
Connect an ‘Audio Out’ device such as a speaker to the camera’s output cable and GND pin of the cable slot. Audio volume is controled from the camera’s the web-viewer.
3 Alarm Out
Connects to alarm lights, siren or lamps. Sensor types are normal open and normal close.
Connect an alarm output device to the camera’s alarm out+ and alarm out- cables in the cable slot.
4 Alarm In
Connect a sensor/alarm input device to the camera’s alarm in+ and alarm in- cables in the cable slot.
10
Installation -
Cabling
Two Options
Use a PoE-enabled switch to connect data and power through a single cable and begin viewing and recording images instantly.
A non-PoE switch will require an adaptor for power transmission.
1. Using a PoE-Enabled Switch
The Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable.
PoE eliminates the need for the di˜erent cables used to power, record, or control the camera. Follow the illustration below to connect the camera to a PoE-enabled switch using an Ethernet cable.
2. Using a Non-PoE Switch
If a PoE-enabled switch is not used, use a power adaptor for power transmission and non-PoE switch for data transmission.
Follow the illustrations below to connect the camera without a PoE-enabled Switch.
Ethernet cable
Power
Ethernet cable
Network Setup -
DW Desktop Tool™
1 Run the CD included with the camera and click on the DW
Desktop Tool™ file.
2 The software will scan your network for all supported cameras and display the results in the table. 'Allow up to 5 seconds for the IP Installer to find the camera on the network.
3 you can press the 'Refresh List' to search the network again, or filter the search results by entering a value in the filter box at the bottom of the page.
4 Check the box next to 'Display Camera Thumbnail' to view a JPEG image of the camera's view next to the camera name on supported models.
5 Select a camera from the list by double-clicking on it. The camera's network information will appear. If necessary, you can adjust the camera’s network type.
Select DHCP if the internet service is dynamic IP. This will allow the camera to receive its IP address from the DHCP server.
Select STATIC to manually enter the camera’s IP address, subnet mask, Gateway and DNS information.
Contact your network administrator for more information.
6 The camera's default network information is:
Default TCP/IP information
- IP: 192.168.1.80
- Subnet Mask: 255.255.255.0
- Gateway: 192.168.1.1
- DNS : 168.126.63.1
7 To view the camera's web client, click on 'View Camera Website'.
A ‘Port Forwarding’ has to be set in your network’s router for external access to the camera.
8 To save the changes made to the camera's settings, input ID and
PW of the camera for authentication.
9 If the camera needs to be rebooted after the settings were changed, press the 'Reboot' button. The camera will power cycle and will appear back in the search results once the reboot is complete.
Default ID / PW : admin / admin
10 Click ‘Save’ to save changed values.
11 To update the camera's firmware from the DW Desktop
Tool™, click on the firmware tab, upload the firmware file and select the cameras to update. You can update multiple cameras at the same time.
Network Setup -
Quick Start of Network Connection
Please follow the steps below to complete the initial setup of the network function.
Do not power on the IP camera until instructed.
Temporarily disable any proxy servers configured in Internet
Explorer.
If the IP camera is connected directly to a modem, power down and reset the modem. Leave the modem powered down until configurations are finalized with the IP camera and the IP camera has been correctly connected to the modem.
10.
Configure the IP camera’s TCP/IP settings as you normally do any other PCs on your network by providing a proper IP address, subnet mask, default gateway, and DNS server.
If this is a stand-alone unit with a direct connection to cable/DSL/
Broadband modem, input the addresses from your ISP. If you have received no IP address from your ISP, select Dynamic and choose the proper settings.
1.
In order to communicate with the IP camera, access your
PC/laptop for configuration.
Keep a record of your PC’s TCP/IP properties (IP address, subnet mask, gateway, DNS, etc.)
Current TCP/IP Settings
IP Address
Subnet Mask
Default Gateway
Primary DNS Server
Secondary DNS Server (Optional)
If your PC obtains its IP address automatically, there is no need to record any information.
2.
Change the IP address of the host PC to 192.168.1.11 and subnet mask to 255 255.255.0 (leave all other entries blank).
3.
Connect the IP camera directly to your PC’s Ethernet port via a crossover cable. (It does not matter what end is used for the PC).
4.
Power on the IP camera using a power adapter.
5.
After 1 minute, verify a flashing ACTIVE indicator and a flashing or solid LINK indicator. After the corresponding indicator lights are properly displayed, open
Internet Explorer.
6.
Type - http://192.168.1.80 (the default IP of the IP camera) into your address bar.
7.
Default ID/Password to access IP Camera are both the word: admin.
8.
Locate the TCP/IP configuration under Setup> Network>
TCP/IP.
9.
Select STATIC under ‘Network Type’ . Select Dynamic only if you are connecting the IP camera directly to your cable/DSL/Broadband modem and your Internet Service
Provider is supplying a dynamic address.
If you have a network with other devices (such as PC/laptop, etc.) or a router, NEVER select Dynamic.
11.
The IP Camera utilizes five TCP ports - Web Port, Video
Port, Control Server Port, and Audio ports. A Web Port utilizes Internet Explorer, a Video Server port supports the streaming video, a Control Server Port transmits control commands to the camera and Audio Ports transmit and receive Audio data. If the IP camera is directly attached to a cable/DSL/Broadband modem or it has been assigned a static IP from your ISP, do not change the default port settings.
If you are installing the IP camera on a network, you must define a Web Port other than 80 as some ISP block port 80.
The other ports can remain unchanged.
12.
If the IP camera is connected to a network utilizing a router, you must have Port Forwarding configured on your personal router to forward all ports to the IP address you have assigned the IP Camera. (See your Network
Administrator for more information).
13.
After configuring Port Forwarding on your router
(if necessary), you may access your IP camera on your local network by opening Internet Explorer and typing the camera’s IP address and Web Port.
Example: http://192.168.0.200:8888
If you leave your Web Port set to 80, you do not need to specify the port in the Address Bar to access to your IP Camera.
14.
Access your IP Camera via the Internet :
If you use a static IP address assigned by your ISP
1) Open Internet Explorer.
2) Type the IP of the IP camera.
3) If you use a router, type the routers’ static IP and the web port
number of the IP Camera.
If you have a dynamic address provided by your ISP
1) Open Internet Explorer and visit the DDNS website.
2) Register the IP camera.
3) Reboot the IP camera.
4) Give the DDNS server up to 10 minutes to locate your IP
camera’s IP information.
5) Click the refresh button in Internet Explore.
Network Setup -
Direct Connection to PC for Initial Setup
This section provides a guide on how to connect the IP camera to your PC/Laptop for initial setup.
Please follow the instructions in the order below. Do not supply power to the IP camera until instructed.
In order to access the IP camera’s firmware you will need to connect the Video Server to a PC or Laptop directly via a network cable.
1.
Before you begin, you must determine the current network/
Internet (TCP/IP) settings on the PC or laptop. Write down your entries below for quick reference.
Current TCP/IP Settings
IP Address
Subnet Mask
Default Gateway
Primary DNS Server
Secondary DNS Server (Option)
For information on how to determine your currents settings, see
Appendix A.
If you are obtaining an IP Address automatically using DHCP
Settings, there is no need to write down the information.
2.
To make the IP camera communicate with your PC, change your PC’s IP address and subnet mask.
Change your PC’s IP address to 192.168.1.11 and the subnet mask to 255.255.255.0
Leave all other entries (Default Gateway, DNS Servers, etc.) blank.
For information on how to change your IP address and subnet mask, see Appendix B.
3.
Attach the IP camera to your PC via a network cable. Plug-in either end of the network cable into the PC’s network slot and the other end into your IP camera.
4.
Power on the IP camera by plugging in a power supply.
5.
Wiat up to 1 minute after powering on the IP camera and verify that the ACTIVE indicator light is flashing, and the LINK indicator light is flickering or solid. If they are not, see FAQ.
6.
You can now access the camera’s viewer using Internet
Explorer.
Open Internet Explorer and type the IP address 192.168.1.80
(default IP of the IP camera) into the Address Bar of the web browser (as seen below). Press Enter.
If a message box as below appears, choose ‘Try Again’. The message will vary depending on the operating system.
7.
Once you connect to the camera successfully, the camera’s login screen will appear.
The 3 authorities are available :
Administrator, Operator and Viewer. The authority setup is available in the camera’s Setup menu.
• Viewer : Only monitoring is allowed.
• Operator : Most of the functions are allowed except
‘Setup’.
• Administrator : All functions are allowed.
8.
The default ID and Password for the camera are both ‘admin’
9.
At any time if you are prompted to download ActiveX controls,
Click ‘Yes’ as all contents are safe.
You will have to click ‘Yes’ twice to two individual prompts. This allows your video to be displayed in Internet Explorer.
Network Setup -
DDNS Registration
If you have DYNAMIC IP service from your
Internet Service Provider (ISP), you will not be able to tell the current IP address of the IP camera.
To solve this problem, you may register to our DDNS service.
Check if you are using dynamic addressing for the camera. If so, register your IP Video Server on our DDNS website before you configure, setup, or install the IP Camera.
Even though your IP is not dynamic, you can register your camera to the DDNS server. This allows you to remember a simple URL address instead of complicated series of numbers like http://201.23.4.76:8078.
For more details, contact our Support Center.
To register IP camera to DDNS, the camera’s ‘Serial No.’ is required.
The ‘Serial No.’ can be found in section 6 ‘Setup - DDNS’ menu.
To use a public DDNS such as ‘dyndns’ or ‘no-ip’, refer to the detail information on how to use the service.
(Visit the web site : http://www.dyndns.com or http://www.no-ip.com for more information).
1
Network Setup -
Guide to Network Environment
Please configure the IP camera at the installation site. Determine your network scenario in order to configure the IP camera with the proper TCP/IP settings.
This tutorial will guide you through the process. Before configuring the IP camera, determine what settings need to be applied.
Record those settings to be used to configure your IP camera for reference.
When configuring your IP camera, treat the
IP camera as any other PC on your network.
You will assign it several addresses and other
TCP/IP properties to match your current network.
This step-by-step tutorial will teach what IP addresses and network configurations should be assigned based on the network scenario.
The default web port is 80. If port 80 is blocked by the ISP, a value between 1025 ~ 60000 should be used. If TCP port 80 is blocked, consult the ISP.
5.
The following descriptions are several basic network scenarios. Determine which scenario describes your network.
If your network does not match one of the scenarios below and you are unsure how to setup your IP camera, contact your network administrator and then call our Support Center.
1.
Before you begin, locate any information and settings received from your Internet Service Provider (ISP). You may need to refer to these IP addresses at a later time during the configuration.
Current TCP/IP Settings
IP Address
Subnet Mask
Default Gateway
Primary DNS Server
Secondary DNS Server (Option)
Static Dynamic
If you were not given any IP addresses or the ISP was responsible for the setup and installation of your Internet connection, go to step 2.
If you are not using a router on your network, your ‘Current
TCP/IP Settings’ from the previous section and ‘Assigned IP
Addresses from My ISP’ will be exactly the same.
2.
You must determine whether the IP address is STATIC or
DYNAMIC. At this moment, you are only concerned via the
ISP. Did they provide you with a STATIC or DYNAMIC address?
If you are unsure, contact your ISP.
3.
Configure your IP camera’s TCP/IP settings for network connectivity by selecting Setup from the camera’s web viewer and selecting TCP/IP under the network settings.
1
Network Setup -
Setup Case A, B
Case A:
Dynamic IP +
Personal Router [Most SOHO]
Camera
Phone Line or CATV Cable/xDSL Modem
(ISP Provided)
PC
Personal Router
W/Intergrated Switch
Internet
Case B:
Static(Fixed) IP +
Personal Router [Efficient]
Public Line
Camera
Gateway or Router at ISP
PC
Personal Router
W/Intergrated Switch
Internet
1
Configure your IP Camera's TCP/IP properties as follows :
1.
Network Type : STATIC (even though you have Dynamic IP from your ISP, use STATIC on the IP Camera)
2.
Internet Address : A private IP address such as
192.168.0.200 (Example)
Assign an IP address to the IP Camera just as you do with PC.
The IP address you assign must be unique to your network and match your network as well. For information on how to choose a unique IP and match your network, read the FAQ.
The IP address you assign must be a private IP. For information on how to choose a private IP please, read the FAQ.
3.
Subnet Mask : 255.255.255.0 (Example)
Use the same subnet mask as the one you noted under ‘Current
TCP/IP Settings’.
4.
Default Gateway : 192.168.0.1 (Example)
This is the IP address of your router. (private or LAN side)
Use the same Default Gateway you noted under ‘Current TCP/IP
Settings’.
5.
Preferred DNS Server : Use the 1st DNS Server from ‘Assigned IP
Address from My ISP’.
If you did not receive any IP addresses from your ISP, contact the ISP and acquire the IP address of their DNS server.
6.
DDNS Server : Use the DDNS server.
This is the same site you will register later to accommodate dynamic IP from your ISP.
7.
Web Port : 8888
Do not use the default port 80 as this number may be blocked by your ISP.
You may select any number between 1025 ~ 60000.
8.
Control Port : 7777
You may select any number between 1025 ~ 60000.
9.
Video Port : 7778
You may select any number between 1025 ~ 60000.
10.
Audio Transmit Port : 7779
You may select any number between 1025 ~ 60000.
11.
Audio Receive Port : 7780
You may select any number between 1025 ~ 60000.
Network Setup -
Setup Case C, D
Case C:
Static(Fixed) IP [Dedicated line directly to the IP Camera]
Case D:
Dynamic IP + DSL/Cable Modem [Connected directly to the IP Camera]
Camera
Camera
Phone Line or CATV
Cable/xDSL Modem
(ISP Provided)
Public Line
Gateway or
Router at ISP
Internet
Internet
Configure your IP camera's TCP/IP properties:
1.
Network Type : STATIC
2.
Internet Address : A static IP address received from your ISP such as 24.107.88.125 (Example)
Assign an IP address to the IP camera just as you do with PC.
3.
Subnet Mask : Subnet mask assigned from your ISP such as
255.255.255.240 (Example)
4.
Default Gateway : 24.107.88.113 (Example)
Use the assigned default gateway from your ISP
5.
Preferred DNS Server : Use the 1st DNS Server from ‘Assigned IP
Address from My ISP’
Contact you ISP to acquire the IP address of their DNS server.
6.
DDNS Server : Use the DDNS server
The same site you will register later to utilize a DDNS service.
7.
Web Port : 80
You may select any number between 1025 ~ 60000.
8.
Control Port : 7777
You may select any number between 1025 ~ 60000.
9.
Video Port : 7778
You may select any number between 1025 ~ 60000.
10.
Audio Transmit Port : 7779
You may select any number between 1025 ~ 60000.
11.
Audio Receive Port : 7780
You may select any number between 1025 ~ 60000.
To connect the IP camera directly to a modem, power down and reset the modem. Leave the modem powered down until configurations are finalized with the IP camera and the IP camera has been connected correctly to the modem. Then power on the modem, followed by the IP camera.
Configure your IP Camera's TCP/IP properties as follows :
1.
Network Type : DYNAMIC
2.
DDNS Server : Use the DDNS server
The same site you will register later to accommodate dynamic IP from your ISP.
3.
Web Port : 80
You may select any number between 1025 ~ 60000.
4.
Control Port : 7777
You may select any number between 1025 ~ 60000.
5.
Video Port : 7778
You may select any number between 1025 ~ 60000.
6.
Audio Transmit Port : 7779
You may select any number between 1025 ~ 60000.
7.
Audio Receive Port : 7780
You may select any number between 1025 ~ 60000.
1
Network Setup -
Port Forwarding
After entering the correct TCP/IP settings, you are ready for ‘Port Forwarding’(Cases A, B).
1.
Record the TCP/IP settings of your IP camera for future reference. You may need this information to access your IP camera and to configure ‘Port Forwarding’.
IP Camera TCP/IP Settings
IP Address
Subnet Mask
Default Gateway
Preferred DNS Server
DDNS Server
Web Port
Control Port
Video Port
Audio Transmit Port
Audio Receive Port
2.
After clicking ‘Apply’, the system will prompt for a reboot.
Please allow the system 50 seconds to reboot and accept the changes. After 50 seconds, close the configuration screen.
The view will display ‘Trying to Reconnect’. If the ACTIVE light on the IP camera has gone off and is now back on again flashing, the IP camera has rebooted. After the system reboots completely, remove the power supply from the unit and close Internet Explorer.
3.
Return your PC/Laptop TCP/IP properties to their original settings.
4.
Before installing the IP camera, you must use ‘Port
Forwarding’ on your personal router (Cases A, B).
You will need to forward 5 ports:
• Web Port
• Control Port
• VideoPort
• Audio Transmit Port
• Audio Receive Port
All the ports will be forwarded to the IP address you assigned to the IP Camera.
In the example above, you would forward:
• 8888 192.168.0.200
• 7777 192.168.0.200
• 7778 192.168.0.200
• 7779 192.168.0.200
• 7780 192.168.0.200
For information on how to use ‘Port Forwarding’, please read
Appendix C.
1
Network Setup -
Starting IP Camera
After forwarding correctly the Web Port,
Video Port, Control Port and two Audio Ports through your router (if applicable), install the
IP camera in a proper location.
1.
Locate the serial number located on the label attached to the bottom of the IP camera, you will need this for DDNS registration.
2.
Connect the IP camera to your router or cable/DSL modem
(per your network scenario) via a Cat5/5e UTP Ethernet network cable.
3.
Supply power to the IP camera (if not using a PoE switch)
4.
After 1 minute, verify the IP camera indicators:
• ACTIVE : Flashing
• LINK : Flickering/Solid
5.
After configuring Port Forwarding on your router
(if necessary), access your IP camera on your local network by opening Internet Explorer and entering the IP address and Web Port assigned to the IP camera.
Examples: http://192.168.0.200:8888 or http://24.106.88.123
If you left your Web Port set to 80, do not specify the port in the Address Bar to access the IP Camera.
6.
Access your IP camera via the Internet :
If you use Case B, C
1) Open Internet Explorer.
2) Type the IP of the IP camera.
If you use Case A, D
1) Open Internet Explorer.
2) Visit the DDNS website.
3) Register the IP camera.
4) Give the DDNS server 10 minutes (MAX) to locate your IP
Camera’s IP information. You may reboot the server to send an
immediate request to our DDNS server.
5) After your camera is connected, select your camera.
The difference between B and C is that B needs to set the port forwarding.
Since the type of DDNS differs from the service type, refer to the related service site.
Web Viewer Screen -
Basic Screen
2 3
4
5
7
6
8
9
1
Web viewer is optimized with Windows XP or above and
Internet Explorer browser.
1 Live video display. This are displays live video stream from the camera.
2 Resolution. The resolution information of the video currently on display.
3 SD Card Search. Searching or Playing images stored in the
SD Card.
4 Setup popup button. Click it to open the camera’s setup page. This allows you to setup the camera’s Video, Network,
Events, System etc.
5 Control tab button. Click the button to extend the panel for full control of the web-viewer’s function.
6 PTZ control button. Click the button to extend the panel to control the camera’s Pan, Zoom, Preset, Tours etc.
7 Full screen button. Click the button to extend the display to full screen. Press ‘Esc’ or ‘Enter’ to return to normal mode.
8 Camera Setup button. Click the button to open the Setup page to setup the camera’s image settings such as lens, white balance, auto exposure, BLC etc.
9 Event alert icon. If Alarm in and Motion detection are detected, below icons will appear.
<Alarm Input> <Motion Detection>
2
Web Viewer Screen -
Control Tab
1
2
6
7
8
3
4
5
1 Live Buffering - When the camera’s image is unsmoothly due to bad network connection, you can setup the camera to delay streaming live video to adjust andimprove image quality. The camera will store live images for the set duration (in miliseconds).
2 Video stream - Select which camera stream to display in the live view screen.
Refer to ‘Setup > Basic > Video’ to setup the Video Stream.
3 Capture - Capture the live video as a BMP or JPG file.
The location and file name can be decided after clicking the button.
4 Print - Print the camera’s current live image for your records.
5 Record - If you click this button, the current live video will be stored as AVI format file in your PC. During the recording, you cannot change the Video Format. If you change the Video Format, the recording will stop.
Recoding directory:
Windows installation driver :\Users\ username \AppData\
LocalLow\IP NETWORK CAMERA\RECORD\ MAC ADDRESS
6 Alarm Input Status - Shows the Alarm Input status. If the status of alarm input becomes On, the ‘Off’ button will changed to ‘On’ button and event alert icon( ) will be displayed on the ‘Live video display’. If alarm is removed, the alarm input status is reset.
Regardless of alarm status, the Alert Icon will remain unless
'Event Display Clear' button is clicked.
7 Relay Out - Enable or Disable relay out function.
8 Event Display Clear - Remove Event Alert Icons resulted from Alarm Input or Motion detection.
22
Web Viewer Screen -
Control Tab
9
10
11
12
13
9 Speaker Control - Enable/Disable Audio stream received from the camera and Volume control of the speaker in the computer.
10 Mic Control - Enable/Disable the Audio stream to the camera.
11 Motion Detection - Enable or Disable motion detection function. ‘Area Setup’ below must be set in advance.
Event Alert Icon( ) will appear on the screen if 'Motion
Detection' is activated. Icon will remain unless 'Event Display
Clear' button is clicked.
While the motion detection is activated, this function is
de-activated momentarily if the OSD and OSD menu is shown on
the screen. It is re-activated once the OSD and OSD menu
disappear.
12 Sensitivity - Define the sensitivity of motion detection. If
High is selected, it will detect very small motion while it becomes relatively insensitive when Low is selected.
13 Area Setup - Setup the target area for motion detection.
1) If ‘Set’ button is clicked, Live screen will display a grid to help area setup.
2) By clicking or dragging mouse on the grids, create or erase the masks on the main view.
3) Motion detection is effective in the masked Area.
4) Save setting by clicking ‘Save’ button.
Area Setup is possible only on the Ch No.1 in the ‘Video Format’.
If you change the video format, motion detection area will return the setup to its default settings.
Unmasked Area
No Detection
Masked Area
Detection E˜ective
2
Web Viewer Screen -
PTZ Control
1
7 8
2
3
4
5
6
9
10
11
12
13
14
1 Pan-tilt wheel buttons - The Pan-tilt wheel enables you to move the camera directions by clicking the corresponding arrow buttons. To move the camera, click and hold the direction arrow. To stop the camera’s movement, release the button.
2 Pan-tilt speed slider - The camera’s pan-tilt speed is controlled by clicking the ‘ + ’ or ‘ - ’ buttons, or by dragging the red-lined slider in the center.
3 Zoom control button - Zoom in and out of the camera’s image by clicking the ‘ + ’ or ‘ - ’ buttons.
4 Preset Selection - View and select a preset number from the drop down list.
5 Go Button - Move the camera to a selected preset.
6 Name Preset - Name the current preset. Max. 9 characters are allowed(Including space).
7 Set Button - Save current location at selected preset.
8 Delete Button - Delete a location of a selected preset.
9 Preset Tour - Select a Tour from the drop-won list.
10 Tour Setup - Select a preset and set the preset’s dwell time during the tour before moving to the next preset. At least 2 presets must be setup prior in order to properly setup a preset tour.
11 Set Button - Save the current preset tour changes.
12 Go Button - Press ‘Go’ button to start running a tour.
13 Clear Button - Clear the selected tour settings.
14 Stop Button - Stop running the selected preset tour.
2
Camera Setup -
Camera Setup
Brightness
Set the brightness of the camera’s image from 0~20. The higher the number, the brighter the camera’s image will appear. Default is 10.
Sharpness
Sets the image sharpness. The higher the number, the sharper the image.
Mirror
Reverse the video from side to side.
Flip
Reverse the video from up to down.
IR LED Mode
Applied for Cameras with IR LED only.
Auto: IR will be set automatically.
Manual: IR can be set manually. ‘Night’ must be selected at
‘Day & Night’ option for manual control of IR.
Day & Night
Auto: In this mode, the IR cut filter is removed automatically depending on the light conditions.
Day: In this mode, the IR cut filter is applied to the image sensor all the time. Thus, the sensitivity will be reduced in the dark light condition but better color reproduction performance are obtained.
Night: In this mode, the IR cut filter is removed from the image sensor all the time. The sensitivity will be enhanced in the dark light condition but the image will be in black and white.
TDN BW Level
The light levels at which the camera will switch from Day mode into
Night mode when Day & Night mode is Auto. The higher the number, the lower the light level. This number should be lower than the value of TDN Color Level.
TDN Color Level
The light levels at which the camera will switch from Night mode into
Day mode when Day & Night mode is Auto.
2
Camera Setup -
Camera Setup
Digital Slow Shutter
Slow shutter mode decreases the speed of the shutter in low light to improve image quality. The slower the shutter, the brighter the image.
However, this can also cause ghosing when fast motino occurs.
Gain Limit
Maximum light gain settings in low light conditions. Select from 0dB
(least light) to 41dB (most light). Default value is 41dB.
DNR
If reduces the noise caused by ‘AGC’ action. If set towards ‘HIGH’, the noise will be reduced but the ghost effect on moving objects will be increased.
White Balance
Auto: White Balance is set automatically based on current conditions.
Auto-Ext: White Balance is set automatically under the assumption of special external illumination like halogen.
Indoor: White Balance is set automatically under the assumption of indoor illumination settings.
Outdoor: White Balance is set automatically under the assumption of outdoor illumination settings.
Preset: White Balance is fixed based on current lighting. Click ‘Set’ in One push Trigger.
Manual: The R/B gain level can be set up manually.
Kelvin
Determines the warmth or coolness of the light. Select from Low,
Middle, or High. Default value is Middle.
One Push Trigger
Click 'Set' continuously until screen image attain an ideal WB.
Shutter
If Shutter is set to Auto, shutter speed is adjusted automatically according to the surrounding illumination.
Shutter Speed
The faster the shutter speed is, moving objects will appear without ghosting effect. However, this will also cause the picture to appear darker if there is no sufficient lighting. This menu is activated when
Shtter is set to Manual.
LED Saturation
Control the LED Saturation.
Defog
Eliminate amount of fog on display screen.
2
Setup -
Video Setup
1
2
3
5
4
1 Live Video Channel/ Stream Setup
The video can be configured to variaty settings with a combination of codec and resolution.
The camera performance has to be considered when setting multiple channels/ streams. This may influence the camera’s performance.
Channel 1 must be set to H.264 in order to activate 'Motion
Detection'.
2 Codec
Choose the video codec. According to the selected codec, the subcategories will change automatically.
When MJPEG is selected, it will be able to set whether to use the relevant channel for image transfer.
The channel for image transfer can only be set to channel 2.
3 Description
Input a description for the selected channel. Max. 15 characters are allowed.
4 Resolution
Select the video resolution.
Available resolution depends on the codec setup between
the channels.
1080p/i
D1
CIF
QCIF
NTSC
1920 x 1080
720 x 480
352 x 240
176 x 120
<Resolution Video Format>
PAL
1920 x 1080
720 x 576
352 x 288
176 x 144
5 Frame Rate
Select the maximum Frame Rate up to 30fps.
Available Frame Rate can be different although same codecs
were set up.
2
Setup -
Video Setup
7
6
8
6 GOP(Group of Pictures) Size
Set up the number of frames (P-frame) which contain only changed information based on basic frame (I-frame) from
1 to 30. In videos with lots of movement, if you set GOP size bigger, only the number of P-frames is bigger. As a result, video resolution will be low but ‘File size’ and ‘Bit-rate’ will decrease.
GOP(Group of Pictures) Size is..
I-frame and P-frame can be created for MPEG4 and H 264 video compression. I-frame(=key-frame) means the whole image data for one specific scene of video. P-frame is image data which has been changed information compared to
I-frame. GOP is made up of one I-frame and corresponding several P-frames. To improve video quality, set the number of P-frames smaller. To decrease image size, set the number of P-frames bigger.
7 Bitrate Mode
Select the bit rate control scheme of video compression from CBR (Constant Bit Rate) or VBR (Variable Bit Rate).
Quality
For VBR, The Target Quality of video can besetup. Set from
1 to 5(Highest). Defualt is 3.
CBR
To guarantee the designated constant bit rate, the quality of video are controlled in this mode. The quality of video is likely to be varying when network traffic is changing.
VBR
To guarantee the designated quality, the bit rate of video stream is changed in this mode. The frame rate of video is likely to varying when network traffic is changing.
This category will be disabled if you select the codec.
8 Target Bitrate
For CBR, you can set the Target Bitrate. Set the target bitrate value from 500 to 8192 kbps. Default is 5478.
Image Transfer
When MJPEG codec is selected, it will be able to set whether to use the relevant channel for image transfer. This option is avilable only for Channel 2.
2
Setup -
Video Setup
9 RTP Multicast
To activate RTP Multicast:
1. Click “Start” button
2. Enter accessible RTP Multicast IP, port for video stream control, RTP packet TTL
3. Click “Apply”. Click “Stop” button to disable RTP Multicast.
You can setup individual RTP Multipcast for each channel/ stream.
10 Click ‘Apply’ to save all changes.
Click the ‘Apply’ button after completing setup for each channel.
2
9
10
Setup -
Audio Setup
1
2
3
1 Input Gain
Adjust the input gain of audio.
2 Output Gain
Adjust the output gain of audio. Output gain 0 is mute.
3 Click ‘Apply’ to save all changes.
Setup -
Panorama Configuration
1
2
1 Position Adjustment
Adjust the video position of each individual lens.
Select a ‘Cam’ and adjust the position by using ‘-’, ’+’ buttons.
Press ‘Set’ to save.
2 Apply to position
After the camera’s positions have been adjusted, click ‘Save’.
Restore : Restore last saved values.
Default : Restore the default value.
Vertical Position
Horizontal Start Position
Cam1
25
193
Cam2
12
241
Cam3
77
189
Horizontal Width 1920 1695 1920
If total width adjustment is down up to 1920, you may see
black video. This time, it’s value is set up to 1920, video is normal.
3
Setup -
Motion Setup
1
2
3
1 Power Up Action
This function enables to resume the last action executed before the camera powered down. Most of actions such as preset, pattern, scan and group are available for this function but jog actions are not available to resume.
2 Parking Action
If ‘Enable’ is set to ‘On’, the camera will run an assigned
‘Camera Action’ automatically if no PTZ command is running during the assigned ‘Wait Time’.
See section ‘Web Viewer Screen_Auto map’ for details of
Preset, Pattern, Scan, Group.
3 Click ‘Apply’ to save all changes.
32
Setup -
OSD
1 Date/Time
Display the current time.
When Date/Time is displayed, deletion of the motion detection mask on the area of Date/Time display are strongly recommended to prevent misdetection on the time’s changing numbers. See Motion Detection Setup for more information.
Unmasked Area
No Detection
Masked Area
Detection E˜ective
2 User Text
Display specific text on the camera’s view.
Support up to 30 characters.
3 Click ‘Apply’ to make above setting effective.
3
1
2
3
Setup -
TCP/IP Setup
1
2
3
5
4
6
7
8
1 Network Type
Select the network type from Static Mode for fixed IP or
Dynamic Mode for dynamic IP address.
If Static is selected, manually enter the camera’s IP Address,
Subnet Mask, Gateway, DNS Server and all ports.
If Dynamic is selected, the camera’s network settings will be assigned automatically by your DHCP router. If you click
‘Apply’, the system will re-boot. To access the camera again, open an Internet Explorer browser and enter the camera’s new IP address in the address bar.
2 IP Address
View or edit the camera’s IP address. The address consists of four numbers separated by dots, each ranging from 0 to
255.
3 Subnet Mask
View or edit the camera’s Subnet Mask.
4 Default Gateway
View or edit the Gateway IP Address. This is your router’s public IP address, and will be used if you are trying to access the camera remotely over the internet.
5 Preferred DNS Server
View or edit the DNS server IP address.
6 Port
The camera requires five ports for different services. To get those services separately, unique port number must be assigned to each service.
7 IPv6 Setting
Create an IPv6 address. If you click ‘Apply’ after checking the IPv6 box, the system will re-boot. If you re-visit this screen after the camera copmletes rebooting, the IPv6 address will be shown.
To use IPv6, network camera has to connect with the router for
IPv6.
8 Click ‘Apply’ to save all changes.
If the network type is dynamic, the camera’s IP address will in cases as below. The IP address will have to be searched again, and the camera will have to be reconnected each time.
- When the camera powers off.
- After Firmware update, Default set and reboot.
It is recommended to set a DDNS address for the camera.
This allows you to connect to your camera using the same
URL all the time, regardless of IP address change.
3
Setup -
RTSP
RTSP Session TimeOut
Check the check box to enable ‘RTSP Settion Timeout’ function.
Select the duration of the time out from 30 to 120 seconds.
1 Click ‘Apply’ to save.
3
1
Setup -
ONVIF
1
2
1 Authentication
None : Allows access without ONVIF authentication.
WS - Username token : Allows access with WS-User
Token of ONVIF authentication.
WS + Digest : Allows access with WS-User Token and
Digest of ONVIF authentication.
2 Click ‘Apply’ to save all changes.
3
Setup -
DDNS Setup
1 DDNS Disable
If it is selected, DDNS service will be off.
2 Basic DDNS
Please register the camera in net4c site so as to use net4c
DDNS. Insert the serial number shown on the screen in the serial entry field.
3 Public DDNS
To use a public DDNS service, select a site listed in the list.
After filling out the Host Name of the site, the setup is completed by entering the User Name and Password registered in that DDNS site.
DDNS Provider
DynDNS
No-IP
Site Address www.dyndns.com
www.no-ip.com
If you setup DDNS properly, the IP address of your camera will update automatically whenever the IP address is changed or the system is rebooted.
If IP updating to DDNS site fails, the camera will keep trying to reconnect every 1minute.
4 Click ‘Apply’ to save all changes.
3
1
2
3
4
Setup -
HTTPS Setup
1
2
3
1 Secure Connection System
Secure Connection System chooses a method of security connection.
HTTP
HTTP mode does not use a security connection method.
HTTPS (Secure connection mode using a unique certificate)
This mode is a security connection method which uses the
(temporary) certiÿcate in the camera.
HTTPS (Secure connection mode using the public certificate)
This mode is a security connection method which uses a certiÿcate issued by certiÿcate authority.
HTTPS (Secure connection mode using the public certificate) method can be selected only if a certificate has been already installed.
When HTTPS mode is chosen, input https://<IP Address> to connect to the camera.
2 Install a public certificate
A certificate issued by Certificate Authority can be installed to the camera and the installed certificate can be deleted.
<How to install or delete the certificate>
1) Input the description (name) of a certificate.
2) Click ‘Install’ after selecting the certificate files and
key file to be installed.
3) To remove the certificate files, click ‘Delete’.
While using HTTPS (Secure connection mode using the public certificate), the certificate cannot be deleted.
3 Click ‘Apply’ to save all changes.
3
Setup -
SNMP Setup
1 SNMP Setup
The camera’s system information can be viewed and configured with SNMP.
2 SNMP V3 Secure Setup
The changes for configuration use version 3 and username and password should be certified at that time.
Username
Username for user authentication.
Authentication Password(MD5)
The Authentication Password (MD5) is an encryption for authentication and must be at least 8 digits long or up to 30 digits.
Privacy Password(DES)
Information protection password is a private encryption and must be at least 8 digits long or up to 30 digits.
3 Click ‘Apply’ to save all changes.
3
1
2
3
Setup -
Status
This menu shows all the information of the Network setting in the camera.
To change these settings, go to the corresponging submenu under the network settings page.
Setup -
Alarm Input Setup
1
2
3
4
1 Input Device Setup
Select input device type from OFF / N.O. / N.C.
Off
NO
NC
Operation
Ignore this Input sensor.
The contact is normally open and closed when activated.
The contact is normally closed and open when activated.
2 Activation Time
Select activation time from Always / Only Scheduled Time.
Always
An alarm event is activated whenever sensor
Input is detected.
Only
Scheduled Time
An alarm event is activated only when sensor input is detected during the scheduled time.
To setup the schedule, you need to define Start time and End time followed by selecting Days.
If End time is earlier than Start time, End time is regarded as next day.
Ex) Assume you select Tue. If you set Start time as 16:00 and End
Time as 09:00, Alarm Input will work from 4:00pm Tue to
9:00am Wed.
3 Action
Define a counter action from Alarm Output / Alarm Image
Transfer / Camera Action when Alarm Input is detected.
Action Description
Alarm Image
Transfer
Turn ON / OFF Image Transfer. Send image via
E-mail or FTP server. (See Transfer Setup for more information).
Alarm Output Activate alarm out (relay).
Output
Duration
Camera
Action
Action
Duration
Select time duration to maintain output.
Setup the Camera Action when Alarm in.
Select time duration to maintain action.
4 Click ‘Apply’ to save all changes.
4
Setup -
Motion Detection Setup
1
2
3
1 Activation Time
Select activation time from Always / Only Scheduled Time.
Always
Only
Scheduled Time
An alarm is activated whenever motion is detected.
An alarm event is activated only when motion is detected during the scheduled time.
To setup schedule, you need to define Start time and End time followed by selecting Days.
If End time is earlier than Start time, End time is regarded as next day.
Ex) Assume you select Tue. If you set Start time as 16:00 and End
Time as 09:00, Alarm Input will work from 4:00pm Tue to
9:00 am Wed.
2 Action
Define a counter action from Alarm Output / Alarm Image transfer when motion is detected.
Action
Alarm Image
Transfer
Description
Turn ON / OFF Image Transfer. Send image via
E-mail or FTP server. (For more detail see
Transfer Setup in this chapter)
Alarm Output Activate alarm out (relay).
Output
Duration
Select time duration to maintain output.
“Alarm output, Output duration” can only be set with cameras which supports alarms.
3 Click ‘Apply’ to save all changes.
42
Setup -
Schedule Setup
1
2
3
4
Schedule function enables you to transfer a series of images in the set time interval via E-mail or FTP. (For more detail, see ‘Transfer Setup’).
This function (Schedule Setup) is enabled when the codec is set to “MJPEG” for channel 2 at “Setup-Video setup”.
1 Enable / Disable
Set Schedule function to be enabled or disabled.
2 Transfer Interval
Define time interval of image transfer.
3 Activation Time
Select activation time from Always / Only Scheduled Time.
Always Transfer image at all times.
Only
Scheduled Time
Transfer image during the scheduled time.
To setup ‘Only Scheduled Time’, you need to define Start time and
End time followed by selecting Days. The setup schedule is repeated every week.
If End time is earlier than Start time, End time is regarded as next day.
Ex) Assume you select Tue. If you set Start time as 16:00 and End
Time as 09:00, Alarm Input will work from 4:00pm Tue to 9:00am
Wed.
4 Click ‘Apply’ to save all changes.
4
Setup -
Transfer Setup
1
2
3
This function is enabled when the codec is set to “MJPEG” for channel 2 at “Setup-Video setup”.
1 Transfer Mode
Select from Disable, FTP and E-Mail (SMTP).
To use image transfer, FTP and SMTP in the next sections must
be configured properly.
2 Pre/Post Alarm Image
Image Transfer due to event is configured by setting Image transfer rate and Pre/Post alarm duration.
Descriptions
Number of Image
Deÿne Number of image transferred per second.
Pre-alarm
Duration
Post-alarm
Duration
Define duration of image transfer before an event.
Define duration of image transfer after an event.
Range of Pre/Post alarm duration varies according to the
number of image setting.
3 Click ‘Apply’ to save all changes.
4
Setup -
FTP Setup
1
2
3
4
5
6
7
To transfer/save images to a site through FTP, FTP must to be setup.
1 Use Passive Mode
Use Passive mode for FTP transfer. If this option is not checked, the transfer will be in Active Mode. Active Mode, may have transfer issues due to firewall settings.
Consult your network manager for more information.
2 FTP Server Address
Enter the FTP’s IP address. If IP Address form is incorrect, a Message box will appear.
3 Upload Path
Define a path in the FTP server to store the video from the camera.
4 Port
Enter the FTP Server’s Port. If Port is incorrect, it will be impossible to access the FTP Server.
5 User ID
Enter the User ID to access the FTP Server.
6 Password
Enter the Password to access the FTP Server.
7 Click ‘Apply’ to save all changes.
4
Setup -
SMTP Setup
1
3
2
4
5
6
7
8
9
10
To send/save images by Email, SMTP needs to be setup.
1 Plain, SSL/TLS
Select the SMTP’s Security mode from Plain or SSL/TLS.
2 SMTP Server Address
Enter the SMTP Server’s Address. If the IP Address form is incorrect, a message box will appear.
3 Port
Enter the SMPT Serve’s port used in the Plain or SSL/TLS security mode.
4 User ID
Enter the User ID to access the SMTP Server.
5 Password
Enter the Password to access the SMTP Server.
6 E-Mail Sender
Enter the e-mail address of the E-Mail Sender. This will be the “From” E-Mail when the camera sends an E-mail.
7 E-Mail Receiver
Enter the e-mail address of the E-Mail Receiver. These addresses will receive notice when the camera sends an
E-mail.
8 Title
Enter the title of the E-Mail to appear when the camera sends an E-mail notification.
The title of the Email is limited to 40 characters.
9 Message
Enter the content of the E-Mail when camera sends an
E-mail notification.
The message of the Email is limited to 40 characters.
10 Click ‘Apply’ to save all changes.
4
Setup -
SD CARD Setup
1
2
3
4
5
6
7
1 SD Card Record
If it is set to On, images will be saved onto the SD card as well.
It will setup OFF automatically when SD card does not applied.
The SD card setting can be configured on the SD CARD section.
2 Total size / Free size
Display total capacity of SD card and the remainder of it.
3 Format
Delete the all contents that stored in SD card.
If the SD card doesn't applied, ‘Format’ button will be deactivated.
4 Auto Delete
Select the period for Auto delete. The image data stored before set period will be deleted automatically.
NONE Do not use ‘Auto Delete’.
1 Week
1 Month
Delete all stored image older than 1 week from 00:00 today.
Delete all stored image older than 1 Month from 00:00 today.
1 Year
Delete all stored image older than 1 Year from 00:00 today.
This function will be executed everyday to delete data before designated period.
5 Capacity Warning E-mail
If enabled, a warning E-mail will be sent when there is less than 8MB of storage space in the SD card. The E-mail will be sent to the e-mail account set in SMTP menu.
6 Overwriting Mode
If enabled, once available space in the SD card reaches less than 8MB, new data will start to overwrite the oldest data.
If it is set OFF and remained space of SD card reaches less than 8MB, image recording will stop.
7 Click ‘Apply’ to save all changes.
4
Setup -
Users Setup
2 3 4
1
1 Users
List all the user accounts for authentication.
2 Add
Register a new user
ID Enter a new user ID except Admin since it exists.
Password Enter the user Password.
Verify Enter the user Password again for veriÿcation.
User Level Select Operator or Viewer.
• Viewer : Only monitoring is allowed.
• Operator : Most of the functions are allowed except ‘Setup’.
• Administrator: All functions are allowed.
Auto Login If you check the auto login for an account, this account becomes the public account. From the next login, everybody can access the camera using this account without authentication. Only one account can have the Auto Login.
The ID and Password are limited to 10 characters.
4
3 Modify
Modify the information of an existing user account.
For admin account, only Password and Auto Login function can be modified.
4 Delete
Delete the selected user account. Admin account cannot be deleted.
Setup -
SYSTEM CAPABILITY
System Capability information.
4
Setup -
Date/Time Setup
1
2
3
4
5
6
1 Timezone Setup
Choose Timezone for camera. It will be activated after clicking ‘Apply’.
It is recommended to set the timezone before setting the
camera’s ‘New Camera Date & Time’.
2 Current Date & Time
Shows the current date and time setting in the camera.
3 Synchronize with my computer
Set the date/time using those of PC currently connected.
4 Setup manually
Set the date/time by typing manually.
5 Synchronize with the time server
Choose a time server available to connect to the camera.
Date & Time will be updated automatically every hour according to the time server.
6 Click ‘Apply’ to save all changes.
Setup -
Firmware Update
Browse...
1
2
3
1 Firmware Version
Displays current Firmware Version in the system.
2 Firmware Filename
Designate the Firmware file name in your computer by clicking [Browse…] button.
3 Start Update
Click this button to start update. Progress will be displayed in the Progress Bar. If you assign the wrong file name, an error massage will be shown.
Warning:
1. Do not turn off the power to the camera during Firmware
update. The system can be stuck and turn unstable.
If updating is completed, the system will reboot automatically.
2. Please make sure to check the ‘Notice’ shown on screen.
If firmware update is completed, the camera will reboot automatically and ‘Setup window’ will be closed.
5
Setup -
Default Set
1
2
1 Reset to the factory defaults
Return the setup to the factory default.
All
Reset all Settings to the factory defaults.
Except Network Setting
&
Panorama Configuration
Except Network related settings and
Panorama settings, reset all others to the factory default.
Warning:
If you click ‘Apply’, you will lose all setting data. If needed, please, make a note for further installation.
2 Click ‘Apply’ to save all changes.
It takes approximatly 4 minutes after clicking ‘Apply’ for the
Default Set.
52
Setup -
Restart
If you click the ‘RESTART’ menu, a message box will be shown to confirm. Click ‘Ok’ to restart.
5
Setup -
Log
System Start, Network Connection Status(Including IP Address), Changing System Time, Changing Video Setup, Network
Setup and Event(Alarm / Motion) Alert will be recorded.
Total 884 pcs logs in each category and the rest will be deleted.
5
Appendix
A : Current TCP/IP Settings
If your IP settings are obtained automatically, you could use the MS-DOS prompt (or Command Prompt) to determine your IP address.
For information on how to do this, please read the FAQ.
1. Windows 98 / ME Users
Start
2. Windows 2000 or XP Users
Start
3. Windows Vista or 7 Users
Start
Control Panel Setting
Control Panel
Network
Conÿguration Tab
Select the TCP/IP
10/100 Protocol
Network and Dial-up
Connection or
Network Connection
Right-click
Local Area Connection
Properties
Control Panel
Network and sharing center
Manage network connections
Click Properties
Note the settings under the IP
Address, DNS Conÿguration, and Gateway tabs
Select the TCP/IP in General Tab
Click Properties
Under the ‘General’ tab of the
TCP/IP Properties you will see your IP address information.
Properties
Select either
Internet Protocol
Ver.4 (TCP/IPv4) or Internet Protocol
Ver.6 (TCP/IPv4)
Click Properties
Under the ‘General’ tab of the
TCP/IP Properties you will see your IP address information.
5
Appendix -
B : Changing IP address and subnet mask
1. Windows 98 / ME Users
Start
2. Windows 2000 or XP Users
Start
3. Windows Vista or 7 Users
Start
Control Panel Setting
Control Panel
Network
Conÿguration Tab
Select the TCP/IP
10/100 Protocol
Network and Dial-up
Connection or
Network Connection
Right-click
Local Area Connection
Properties
Control Panel
Network and sharing center
Manage network connections
Click Properties
Select 'Use the following IP address' and change the IP address and Subnet Mask.
Select the TCP/IP in General Tab
Click Properties
Select 'Use the following IP address'
Properties
Select either
Internet Protocol
Ver.4 (TCP/IPv4) or Internet Protocol
Ver.6 (TCP/IPv4)
Click Properties
Select 'Use the following IP address'
5
Appendix -
C : Port Forwarding
After assigning the IP Camera a web server port and video server port use Port Forwarding.
(for cases A, B)
2.
For Linksys BEFSR41 Cable/DSL routers:
1) Open a web browser and type http://192.168.1.1
2) Enter your User Name and Password to
Default: User Name:[leave blank] Password: admin.
Consult your router’s manual to properly configure Port Forwarding.
For your convenience, we have provided two example configurations.
3) Select “Applications & Gaming” from the menu bar.
4
1.
For D-Link DI-604 broadband routers:
1) Open a web browser and type http://192.168.0.1
2) Enter your User Name and Password to
Default: User Name: admin Password: [leave blank].
3) Select the “Advanced” tab and click “Virtual Server”.
1
2
4) Click “Apply” after inputting proper values.
4) Input port numbers in “Port Range” as below and click
“Save Setting”. Both Web Server Port and Video Server
Port should be added.
5
3
Enabled / Disabled
Name
Private IP
Protocol Type
Private Port / Public Port
Schedule
Select “Enabled”.
Input IVS name.
Input IVS address.
Select “TCP”.
Input IVS Web Server Port.
Select “Always”
5) If 'Setting Saved' shows, click [Continue] button.
6) Repeat these steps to add the Video Server Port.
7) The Web Server Port, Video Server Port and 2 Audio Ports shows in "Virtual Server List" as below.
Enabled / Disabled
Start / End
Protocol
IP Address
Enabled
6
Input IP Camera name.
Input IP Camera Web Server Port and Video
Server Port.
Start should be same as End.
Both of Web Server Port and Video Server
Port should be added.
Select “TCP” in Protocol option.
Input IP Camera IP Address.
Check the square.
5
Appendix -
C : Port Forwarding
3.
For Netgear RP614 routers:
1) Input http://192.168.0.1 in address bar of web browser.
http://192.168.0.1 is the default IP address.
2) Input the username and password (admin as ID and password as password).
3) Click “Port Forwarding” in "Advanced".
page.
1
5) Input proper values in "Ports - Custom Services" as
below.
2
Enable
Service Name
Starting/
Ending Port
Server IP Address
Check the box to activate the entry.
Input the IP camera’s name.
Input the IP camera’s Web Server port.
Starting Port should be same as Ending Port.
Input the IP camera’s IP Address.
7) With the same method as above, add Video Server Port.
8) Click "Apply" to complete Port Forwarding.
5
Appendix -
FAQ
1.
My POWER light is not on?
Power is not being supplied to the unit. Please use a proper power supply and verify that a power source is active from the attached power outlet used to connect the adapter. You can test this by plugging in any other electrical device and verify its operation. After making sure the power cable and power supply are working properly, reinsert the power connector into the IP camera. If using a PoE switch, make sure the switch provides the correct amount of power necessary to power the IP camera and that the port is working.
7.
I can’t connect!!
In case of a connection failure.
Modem Reboot > Modem Reboot Finished > Router Reboot
> Router Reboot Finished > IP Camera Reboot > IP Camera
Reboot Finish > Verify DDNS and IP Camera connection, if applicable.
8.
How do I “PING” an IP address?
1) Open an MS-DOS (or Command) prompt
2) At the prompt type - “ping xxx.xxx.xxx.xxx” (without the quotes and replace the “x”s with an IP address)
3) Press Enter
2.
My ACTIVE light is not flashing?
Verify the power supply to the unit. Power off the unit and back on again, wait 1 minute, if the ACTIVE light still does not begin to flash, you will have to set the unit to its factory default (THIS WILL DELETE ANY CONFIGURATION SET
MANUALLY). Power on the unit and press the reset button for five (5) seconds.
3.
4.
5.
My LINK light is not flashing or solid?
Verify the cable connection. Try using a different network cable or crossover cable (for PC connection only).
I can access the video server on my LAN, but not from the
Internet.
Verify that your router (if applicable) has port forwarding properly configured. If accessing from our DDNS service, verify correct serial number. Check that your Firewall settings are not blocking access to the camera.
How do I open an MS-DOS or Command Prompt?
• Windows 98 / ME Users :
Start > Programs > Accessories > MS-DOS prompt
• Windows 2000 / XP Users :
Start > (All) Programs > Accessories > Command Prompt
9.
10.
I’m accessing my video server remotely over the Internet and the video stream is choppy, is this normal?
Yes. The frames per second received remotely are determined by your bandwidth capabilities both at your site where the IP Camera is installed and your remote location.
The lower of the two sites will determine how fast your video stream is received. It is recommended to have at least a 256Kb/sec upstream connection from the site where the IP
Camera is installed. Lower speeds will operate properly, but provide poor remote performance. The Faster the
Internet connection at both ends, the faster the video stream.
How do I enable or check ActiveX on my browser
Open Internet Explorer > Tools on the menu bar > Internet
Options > Security Tab > Custom Level > Scroll down and verify that you are prompted or have enabled ActiveX controls and plug-ins to be downloaded and executed. > click OK > restart browser.
6.
How do I find out my IP address information if my settings were automatically detected?
Windows 98 / ME Users
1) Open an MS-DOS Prompt
2) At the prompt type: “winipcfg” (without the quotation marks)
3) Use the drop down list to select your 10/100 Ethernet Adapter
(not a PPP adapter)
4) Now you will see your IP Address, Subnet Mask, and Default
Gateway information
5) For DNS information contact your Internet Service Provider
11.
How do I reset the unit to factory defaults?
On the underside of the unit you will find a recessed opening located near the top-left side of the label. Power on the unit and use a paper clip to push the reset button in.
The ACTIVE light in the camera module will turn off and after a few seconds the ACTIVE light will begin to flash, signifying a successful reboot. If the ACTIVE light does not turn off after pressing the reset button, please try holding the button in for a few seconds and releasing.
Please note: YOU WILL LOSE ALL DATA THAT HAS BEEN
ENTERED PREVIOUSLY AND THE IP CAMERA WILL BE SET TO
ITS FACTORY SETTINGS.
Windows 2000 / XP Users
1) Open a Command Prompt
2) At the prompt type - “ipconfig /all” (without the quotes)
3) Near the end of the information supplied, should be your current IP address, subnet mask, default gateway and DNS servers
5
Specifications -
Dimension
Unit: mm
ø150
ø150
61.9
19
145
48.5
Warranty Information
Digital Watchdog (referred to as “the Warrantor”) warrants the Camera against defects in materials or
workmanships as follows:
Labor: For the initial two (2) years from the date of original purchase if the camera is determined to be defective, the Warrantor will repair or replace the unit with new or refurbished product at its option, at no charge.
Parts: In addition, the Warrantor will supply replacement parts for the initial two (2) years.
To obtain warranty or out of warranty service, please contact a technical support representative at
1-866-446-3595 Monday through Friday from 9:00AM to 8:00PM EST.
A purchase receipt or other proof of the date of the original purchase is required before warranty service is rendered. This warranty only covers failures due to defects in materials and workmanship which arise during normal use. This warranty does not cover damages which occurs in shipment or failures which are caused by products not supplied by the Warrantor or failures which result from accident, misuse, abuse, neglect, mishandling, misapplication, alteration, modification, faulty installation, set-up adjustments, improper antenna, inadequate signal pickup, maladjustments of consumer controls, improper operation, power line surge, improper voltage supply, lightning damage, rental use of the product or service by anyone other than an authorized repair facility or damage that is attributable to acts of God.
6
Limits & Exclusions
There are no express warranties except as listed above. The Warrantor will not be liable for incidental or consequential damages (including, without limitation, damage to recording media) resulting from the use of these products, or arising out of any breach of the warranty. All express and implied warranties, including the warranties of merchantability and fitness for particular purpose, are limited to the applicable warranty period set forth above.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights from vary from state to state.
If the problem is not handled to your satisfaction, then write to the following address:
Digital Watchdog, Inc.
ATTN: RMA Department
5436 W Crenshaw St
Tampa, FL 33634
Service calls which do not involve defective materials or workmanship as determined by the Warrantor, in its sole discretion, are not covered. Cost of such service calls are the responsibility of the purchaser.
62
Headquarters Office: 5436 W Crenshaw St, Tampa, FL 33634
Sales Office: 16220 Bloomfield Ave., Cerritos, California, USA 90703
PH: 866-446-3595 | FAX: 813-888-9262 www.Digital-Watchdog.com
Technical Support PH:
USA & Canada 1+ (866) 446-3595
International 1+ (813) 888-9555
French Canadian 1+ (514) 360-1309
Technical Support Hours: Monday-Friday
9:00am to 8:00pm Eastern Standard Time

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- 2.1MP resolution
- 180° panoramic lens
- SD card recording
- PoE support
- PTZ control
- Motion detection
- Alarm input and output
- Audio recording and playback
- Web viewer interface
- DDNS support