WARNING WARNING CAUTION CAUTION

WARNING WARNING CAUTION CAUTION
INSTRUCTION MANUAL
CEILING FLUSH-MOUNT SPEAKER ES-C0651
Thank you for purchasing TOA’s Ceiling Flush-Mount Speaker.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read
all the instructions in this section for correct and
safe operation.
• Be sure to follow all the precautionary instructions
in this section, which contain important warnings
and/or cautions regarding safety.
• After reading, keep this manual handy for future
reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below
are used in this manual to prevent bodily injury and
property damage which could result from mishandling.
Before operating your product, read this manual first
and understand the safety symbols and messages
so you are thoroughly aware of the potential safety
hazards.
WARNING
Indicates a potentially hazardous situation which,
if mishandled, could result in death or serious
personal injury.
CAUTION
Indicates a potentially hazardous situation which,
if mishandled, could result in moderate or minor
personal injury, and/or property damage.
WARNING
When Installing the speaker
• Install the speaker only in a location that can
structurally support the weight of the speaker and
the mounting bracket. Doing otherwise may result
in the speaker falling down and causing personal
injury and/or property damage.
• A sliding retainer clip is designed to temporarily
hold the speaker in four places during installation
and service. Always be sure that the speaker is
further secured by the anchor bolt to ensure that
it does not accidentally fall and possibly result in
personal injury.
• Use only the speaker’s specified front grille and
matching transformer. If any other front grille or
matching transformer is used, it could detach and
fall, resulting in personal injuries.
When the speaker is in Use
• Should the following irregularity be found during
use, immediately switch off the power amplifier
which is driving the speaker and contact your
nearest TOA dealer. Make no further attempt to
operate the speaker in this condition as this may
cause fire or electric shock.
· If you detect smoke or a strange smell coming
from the speaker.
· If water or any metallic object gets into the speaker
· If the speaker falls, or the speaker case breaks
· If it is malfunctioning (no tone sounds.)
CAUTION
When Installing the speaker
• Since installation requires specialized skills and
professional experience, always consult the
shop from where the unit was purchased before
beginning installation. If the speaker should fall, it
could result in electrical shocks or other personal
injuries.
When the speaker is in Use
• Do not operate the speaker for an extended
period of time with the sound distorting. This is an
indication of a malfunction, which in turn can cause
heat to generate and result in a fire.
• Have the speaker unit checked periodically by the
shop from where it was purchased. Failure to do so
may result in corrosion or damage to the speaker or
its mounting bracket that could cause the speaker
to fall, possibly causing personal injury.
2. GENERAL DESCRIPTION
The ES-C0651 is a high power ceiling flush-mount speaker designed to be mounted to the medium and high ceiling.
3. FEATURES
• Newly-developed, high-efficiency 25 cm coaxial speaker with high power handling capabilities.
• Compression driver with aluminum diaphragm assures high power reproduction.
• New coaxial horn (constant directivity of 60° horizontal by 60° vertical) assures a uniform, well-controlled pattern of high
frequency sound dispersion.
• Anchor bracket supplied.
• Push-in speaker connection and terminals facilitate installation.
4. Nomenclature
[Speaker]
[Anchor Bracket]
Safety wire mounting bracket
Anchor bolt mounting hole
Mounting screw (M4x12)
Blank panel
Push-in terminals
Mounting tab B
Mounting tab A
Sliding bracket mounting slot
Note : The anchor bracket is mounted to the enclosure
when unit is supplied from the factory.
5. Installation Procedure
Anchor bolt
Nut
About 170 mm
1. Make a 320 mm diameter hole in the ceiling and secure
the anchor bolt in the position shown in the figure. Then
thread a nut halfway up the length of the bolt.
3. Slide a plain washer over the anchor bolt. Then fit the
anchor bracket into the ceiling hole and insert the anchor
bolt into the oval hole in the anchor bracket.
Ceiling panel
Anchor bracket
Plain washer
ø320 mm
2. Screw a wing bolt halfway into each of the sliding retainer
clips, and leave the bolt sticking out about 3 mm.
Wing bolt
Sliding retainer clip
About 3 mm
4. Attach the four sliding retainer clips to the legs of the
anchor bracket by inserting the heads of the wing bolts
into the corresponding slots, then slide the clips down to
grasp the ceiling panel between the clips and the ends
of the anchor bracket, then secure with the bolts.
Anchor bracket
Sliding retainer clip
5. Slide a plain washer and a spring washer onto the end
of the anchor bolt, then thread on two nuts. Secure by
clamping the anchor bracket tightly between the bolt’s
upper and lower nuts.
8.Connect the speaker cables to the push-in terminals
located on the side of the speaker. The terminals can
also be used for bridge connection (parallel connection)
of multiple speakers.
Nut
Plain washer
Push-in terminals
Plain washer
Spring washer
Nuts (2)
Speaker unit
Less than
32 mm
Note
Take care that the anchor bolt does not protrude more
than 32 mm from the inside of the anchor bracket.
6. Screw the supplied mounting screws (M4 x 12) into the
bases of the anchor brackets with their heads sticking
out approximately 3 mm.
9. Push the speaker up in the ceiling hole and rotate it
counter-clockwise to catch the speaker’s mounting tabs
A on the speaker mounting screws, as shown in the
figure below. Then secure by tightening the mounting
screws.
Mounting screw
Mounting tab A
About 3 mm
Mounting screw
7. Wrap a safety wire round a heavy-duty ceiling beam or
C channel, then connect the snap ring to the safety wire
mounting bracket.
Rotate the speaker until the mounting
screws completely fit into the notches
of Mounting tabs A.
10.Secure two mounting tabs B as well by tightening the
supplied mounting screws (M4x12).
Safety wire
Mounting tab B
Mounting screw
Snap ring
Safety wire
mounting bracket
6. About the combination with optional equipment
6.1. Attaching an Optional Front Grille FG-C0651
Squeeze the two springs of the front grille and mount them to their corresponding spring catch holders located on the side
of the speaker.
The speaker complete with a front
grille attached by means of a spring.
Note : For specifications of the front grille FG-C0651, refer to the instruction manual attached to the front grille.
6.2. Installing an Optional Matching Transformer MT-S0601
To install the MT-S0601 transformer in the speaker system,
remove the blank panel located at the side of the speaker. For
the installation method, refer to the instruction manual attached
to the MT-S0601 transformer.
MT-S0601
Primary terminal
83Ω
170Ω
330Ω
670Ω
High impedance High impedance
100 V line
70 V line
60 W
60 W
30 W
30 W
15 W
15 W
7.5 W
6.3. Low Frequency Equalization By Digital Signal Processors
Low frequency characteristics can be corrected using TOA’s
digital signal processor. When using the speaker in combination
with the digital signal processor, the settings shown in the table
at right are recommended.
TYPE
HPF
PEQ
PEQ
PEQ
Freq.
40 Hz
90 Hz
180 Hz
630 Hz
Gain
+10 dB
-4 dB
+3 dB
Q
Q 0.500
Q 2.456
Q 1.414
Q 1.850
7. SPECIFICATIONS
Enclosure Type
Power Handling Capacity
Nominal Impedance
Output Sound Pressure Level
Frequency Response
Crossover Frequency
Speaker
Input Terminals
Anchor Bolt Installation
Ceiling Hole
Enclosure Depth
Materials
Weight
Sealed type
180 W (continuous program)
60 W (continuous pink noise)
8Ω
96 dB (1 W, 1 m)
80 Hz – 20 kHz
2.5 kHz
Coaxial speaker
Low frequency : 25 cm cone speaker
High frequency : CD horn (60° x 60°) plus compression driver
Push-in terminals
Anchor bolt receptacle (anchor bracket) attached.
Round hole with diameter of 320 mm
200 mm
Enclosure : Wood (Medium density fiber or MDF)
Anchor bracket : Steel plate
6.8 kg (including an anchor bracket)
Note: The design and specifications are subject to change without notice for improvement.
• Accessories
Sliding retainer clip .............................................................................................................
Wing bolt (M4x8) ................................................................................................................
Pattern papers (one for round hole and one for anchor bolt position setting) ....................
Safety wire ..........................................................................................................................
4
4
2
1
URL: http://www.toa.jp/
133-01-00024-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement