INSTALLATION AND SETUP GUIDE

INSTALLATION AND SETUP GUIDE
N5987-1V2 9/06 Rev. B
ADEMCO 5890AP
PASSIVE INFRARED MOTION DETECTOR/
TRANSMITTER WITH PET IMMUNITY
INSTALLATION AND SETUP GUIDE
The ADEMCO-5890AP Passive Infrared Motion
Detector/Transmitter is a battery-operated
wireless device intended for use as part of a
5800AP series wireless alarm system.
Designed for use in commercial and residential
installations, the 5890AP is a wall-mounted unit
with a standard lens that provides wide-angle
protection up to a range of 10.6m. For best
coverage, mount the detector so that the likely
direction of intruder motion is across the
pattern.
When installed per the guidelines, the SplitZone Optics technology in the 5890AP provides
reasonable false alarm protection against pets
and other animals up to 18.1 kg.
This document provides installation instructions
for the 5890AP, but the installer must be
familiar with the installation instructions for the
5800 Wireless Alarm System with which the
5890AP is intended to be used.
FEATURES
• Split-Zone Optics provides pet immunity
against animals up to 18.1 kg.
• Wireless operation for fast installation.
• Dual-element pyroelectric sensor provides
positive protection while minimizing false
alarms.
• Alternate-polarity pulse count option offers
greater stability in adverse environments.
• Provision to turn LED on while Walk Testing
(LED is turned off after testing).
• Tamper-protected cover; unit transmits
message if cover is removed.
• Wall or corner mounting options.
SYSTEM DESCRIPTION
Optical System
Uses efficiently designed Fresnel lenses with
Split-Zone Optics.
Radio Transmitter
The built-in transmitter serves only as the
communication link to the alarm system's
Receiver/Control, and can send alarm, tamper,
supervisory, and battery status messages to
the system's receiver/control. The transmitter is
not used for detection purposes. Each detector
has a unique serial number permanently
assigned at the factory. You must enroll this
serial number into the control system at the
time of installation. This allows each detector
used in the system to be uniquely identified.
To conserve battery life during normal
operation, no more than one transmission
sequence will occur within a 3-minute period.
There is no such time restriction in Test mode.
Alternate-Polarity Pulse Count
Two jumper-selectable detection response
modes are provided: Instant response (Pulse
Count OFF) and Alternate-Polarity Pulse Count
(Pulse Count ON). With Pulse Count OFF, any
detected change in infrared energy triggers an
immediate alarm signal.
This mode is recommended when the detector
is used to monitor a narrow hallway where
coverage is provided by only a single zone. Use
the Pulse Count ON mode when the detector is
installed in areas where periodic changes in
infrared energy levels are normal (for example,
where forced-air heating ducts are present). In
this mode, at least two changes in infrared
energy must be detected within a short period
before an alarm is triggered.
Important Note: For pet immunity applications, Pulse Count ON is recommended.
SPECIFICATIONS
Frequency:
Pet Immune
Lens:
315Mhz
10.6m x 13.7m.
30 zones (8 long, 7 over 7 intermediate, 4 over 4 short-range).
Pulse Count: Installer-selectable On/Off link.
Detectable
Walk Rate:
0.15–1.5m/Sec.
Mtg. Height: (2.1m) recommended,
but may be mounted at other
heights (see Table 1).
Walk Test
Indicator:
Red LED with Test/Normal
(disable) link.
Batteries:
Two 3-volt Lithium batteries.
Use only ADEMCO No. 466,
Duracell DL123A, Panasonic
CR123A, Sanyo CR123A, or
Varta CR123A.
0perating
Temperature: 0°C - 50°C.
Operating
Humidity:
Up to 95% RH (max.), noncondensing.
Dimensions: 68mm x 127mm x 48mm.
7.6m
BATTERY INSTALLATION
1. Remove front cover by inserting a large
screwdriver blade (or small coin) in groove
between cover and base at the location
shown in Figure 2; rotate blade to override
snap fit, then lift cover off.
2. Observing correct polarity, install the two
Lithium batteries (supplied) into the battery
holders, as shown in Figure 5. Make sure
the batteries are firmly seated.
3. Replace the cover (snap fit).
Battery Caution
Risk of fire, explosion, and burns. Do not
recharge, disassemble, heat above 100°C, or
incinerate. Dispose of used batteries promptly.
Keep away from children.
Programming Note: If you have not
programmed the detector’s serial number
into the system (i.e., this is an initial detector
installation), refer to the PROGRAMMING
section below and perform the serial number
enrolling procedure before mounting or
testing the detector.
PROGRAMMING
You must enroll the detector’s serial number
during installation of the system. You should
program the 5890AP as an “RF” type unit
(i.e., supervised RF), and the "Loop"
number as "1."
To program the detector, place the LED jumper
in the TEST position (see Figure 5), the Pulse
Count jumper in the OFF position, batteries
installed and cover on. Temporarily cover the
lens (a cloth will do) to prevent any activation
by the detector.
When prompted for the device’s serial number,
you may either manually enter it or transmit
from the unit (remove the cloth cover and
motion your hand over the lens to activate the
detector, press the tamper switch, etc.). Refer
to the control panel installation instructions for
programming details.
Return LED jumper to the NORMAL position
after it is enrolled in the control.
INSTALLATION
0
ALTERNATE
COUNT POLARITY
EACH ZONE CONSISTS
OF 2 FIELDS
7.6m
3m
6m
9m 10.6m
3m
6m
9m 10.6m
2.3m
0
0
Figure 1. Protection Pattern
5890AP(i)Ptrn
GENERAL INFORMATION
Installation Hints
• Do not install where the detector is exposed
to direct sunlight or directly above strong
sources of heat.
• Make sure the detection area does not have
obstructions (curtains, screens, large pieces
of furniture, plants, etc.) that may block the
pattern of coverage.
• Avoid locating a unit in areas that contain
objects likely to produce a rapid change in
temperature, such as central heating,
radiators, or ducts (or heaters of any kind),
air conditioners, open flame, etc.
• Do not mount on an unstable surface.
IMPORTANT: For installation with pets, be
sure to follow the guidelines described in
Table 2.
1. Remove front cover.
2. Squeeze upper lens lock located in front
cover to release upper Fresnel lens support.
Squeeze lower lens lock to release lower
Fresnel lens support (see Figure 4).
3. Note how the lens supports are positioned,
then remove the supports.
4. Carefully remove the existing lens and
replace it with an optional coverage
replacement lens. The lens must be
installed with the smooth side facing
outward. Also, the lens should be oriented
with its part number on the upper right-hand
side (see Figure 4). Be sure to center the
lens.
Note: Lens surface should be free of dirt,
foreign matter, and fingerprints. Use a
clean, dry, soft cloth to wipe lens surfaces,
if required.
5. Replace top and bottom lens supports and
then press downward so that the lens locks
snap into position, securing the lens in
place.
6. Refer to Table 1 for recommended PIR
mounting height.
7. Replace the front cover (make sure the
cover snaps tightly).
LENS
UPPER LENS SUPPORT
LENS LOCK
INSTALL
LENS
WITH
PART #
IN THIS
POSITION
LENS LOCK
LOWER LENS
SUPPORT
Figure 4. Changing Lenses
VERTICAL PATTERN ADJUSTMENT
2) LIFT COVER
1) INSERT
SCREWDRIVER
HERE AND
TWIST
Figure 2. Cover Removal
B
A
B
C
KNOCKOUTS
"C" (2)
FOR RECESS
MOUNTING
C
B
A
KNOCKOUTS
"A" (2)
FOR SURFACE
MOUNTING
B
KNOCKOUTS
"B" (4) FOR
CORNER
MOUNTING
Figure 3. Mounting Holes in Base
RECESS MOUNTING
Recessed mounting requires the use of the
optional No. 1990MK Recess Mounting Kit.
Complete instructions for the use of this kit
accompany it.
Note: Holes "C" in the detector base
(accessible only when the PC board is
removed) are used for recessed mounting.
The protection pattern provided by the lens in
use can be raised or lowered by re-positioning
the PC board in the detector. A graduated scale
to the right of the board (see Figure 5) indicates
the approximate number of degrees by which
the pattern can be raised (max. +5°) or lowered
(max. -15°). The detector is normally shipped
with the board set to the 0° position. To make
this adjustment, remove the cover on the
detector and loosen the screw holding the PC
board (the screw is located at the approximate
center of the board). Slide the board upward or
downward by the number of degrees required,
then tighten the holding screw again. After any
adjustment, you must conduct a Walk Test to
ensure proper coverage of the area to be
protected,
as
indicated
under
TEST
PROCEDURES.
The protection pattern provided by the lens can
be moved to the left or right by horizontal
adjustment of the lens, as follows:
1. Remove front cover.
2. Press inward on the upper and lower lens
locks at the left or right side only to release
the lens supports on one side. Now slide
the lens to the left or right, as needed. The
lens may be moved as much as 8° from
center in either direction.
3. When the lens is in the desired position,
press the lens locks downward on the
released side to lock the supports in place.
4. Replace the front cover (make sure the
cover snaps tightly).
After any adjustment, you must conduct a Walk
Test to ensure proper coverage of the area to
be protected, as indicated under TEST
PROCEDURES.
PULSE COUNT OPTION
Each detector includes pulse count circuitry
that is designed to provide stability in adverse
environments to minimize false alarms. Pulse
count is selected by positioning a jumper
across the ON pulse count terminals (shown in
Figure 5). When set for pulse count ON, the
detector will signal an alarm within 2 or 3 steps,
because the processing logic requires more
complex motion than just a momentary event.
When the detector verifies an intrusion, the
built-in transmitter will send an alarm message
to the control/receiver.
Important Note: For installations with pets,
Pulse Count ON is recommended.
LED DISABLE
The detector is shipped with the LED disabled
(LED jumper in the "NORMAL" position). The
LED may be enabled (for the Walk Test) by
positioning the LED jumper in the "TEST"
position (see Figure 5).
Note: When the jumper is in the "NORMAL"
position, the LED does not light, but the built-in
transmitter transmits alarms when the PIR
senses motion.
PULSE
COUNT
ON-OFF
DETECTOR
OFF
LENS MASKING
The supplied masking strips are designed for
application to one or more lens segments to
produce a protection pattern that suits the
particular requirements of the protected area.
Individual masking strips have been provided
for each of the lens segments on the standard
lens supplied with the PIR. Simply peel off the
appropriate pressure-sensitive adhesive strip(s)
and apply over the desired lens segment(s). Be
sure to affix the masking strips to the inside of
the lens (not the outer, smooth side).
-2-
SECURING
SCREW
PULSE
COUNT
ON
NORMAL
Mount the unit to a firm vertical surface (flat on
a wall or in a corner).
1. Remove the front cover.
2. Temporarily loosen (do not remove) the
screw holding the PC board in the detector
base (see Figure 5 for location of this
screw).
The board can then be moved up or down
for access to the knockout mounting holes
in the base.
3. Refer to Figure 3 for location of knockout
holes in the base. Break out only those
holes required.
4. Mount the detector with screws, using the
selected mounting holes.
5. Before fully tightening the PC board holding
the screw, make sure the board is
positioned so that the arrow is in line with
the appropriate setting on the graduated
scale on the right-hand side of the PC board
(see Table 1 and Figure 5).
HORIZONTAL ADJUSTMENT OF LENS
3 VOLT LITHIUM
BATTERY
NORMAL MOUNTING
Each lens segment that is masked results in
the elimination of one zone of protection from
the coverage pattern. By masking segments of
the lens, you can adjust the coverage to suit
the area to be protected, or eliminate coverage
from areas where you anticipate environmental
disturbances that might reduce the PIR's
stability (a heater or other heat-producing
object, for example).
LED
TEST
CHANGING LENSES (if required)
Verify that a strong transmission path between
the 5890AP and the system's Receiver/Control
exists before permanently mounting the
detector. Do this by performing the Walk Test
(described later) with the detector temporarily
mounted in its proposed location. The 5890AP
will transmit when sensing motion (such as a
person waving an arm or walking into an area).
Sometimes, moving the detector only a few
centimeters means the difference between a
strong and weak transmission path. Experiment
until you are satisfied that the location provides
the strongest transmission path, yet is still
practical for the protection pattern desired.
This test also verifies that the detector has
been correctly programmed into the system.
3 VOLT LITHIUM
BATTERY
RADIO TRANSMISSION PATH CHECK
5
0
-5
-10
-15
LED
NORMAL (OFF)
TEST (ON)
TAMPER
SWITCH
Figure 5. PC Board
TEST PROCEDURES
WALK TEST
MAINTAINING PROPER OPERATION
Important: Testing should be conducted with
the protected area cleared of all people. Place
the protective system's control in the Test
mode for the Walk Test procedure. When the
PIR senses movement, the system's console
emits a beep, verifying that the PIR's
transmitter signal has reached the control's
wireless receiver.
1. Remove front cover and set the pulse count
jumper in the detector in the OFF position
In order to maintain the detector in proper
working condition, it is important that the user
observes the following:
The absolute range of all PIR units is subject to
variation because of different types of clothing,
backgrounds, and ambient temperature. For
this reason, ensure that the most likely intruder
routes are well within the PIR's protective zones
and that Walk Testing is carried out along these
routes.
initially. The LED must be enabled at this
time (jumper in the TEST position).
2. Replace front cover and walk through
protective zones, observing that the
detector's LED lights whenever motion is
detected (the LED serves as a Walk Test
indicator during this procedure).
3. If pulse count is going to be used in this
installation, set the pulse count jumper to
the ON setting and repeat the Walk Test
procedure.
Note: If pulse count mode is used during
the Walk Test, the LED will stay lit for
approximately 1 to 3 seconds after
detecting motion.
1. Replace both batteries within 7 days after a
"low battery" message has appeared in the
system's display.
2. Detectors should never be re-aimed or
relocated without the advice or assistance
of the alarm service company.
3. The physical surroundings of the protected
area should not be changed. If furniture or
stock is moved, or air conditioning or
additional heating is installed, the PIR may
have to be readjusted.
4. Walk Tests should be conducted frequently
(at least weekly) to confirm continued
proper coverage.
4. After the Walk Test is completed, the
LED jumper should be placed in the
NORMAL position (LED disabled).
TABLE 1. INSTALLATION GUIDE FOR MOUNTING HEIGHTS
Lens
Part No.
Description/ Coverage
Pulse
Count
PIR Mounting
Height
5890AP (Standard as
installed)
Pet Immune Lens:
10.6m x 13.7m
Required for
installations with pets
2.0m
Pattern Setting
(Deg) †
+2°
2.1m
+1°
2.3m
+1°
← Optimum Pet Immunity
† See Figure 5 for location of adjustment scale on PC board (refer also to VERTICAL PATTERN ADJUSTMENT).
SPECIAL INSTRUCTIONS FOR INSTALLATION WITH PETS
To take full advantage of the pet immunity in the 5890AP, the guidelines below should be followed:
• Mount the center of the detector 1.9m to 2.3m high and adjust the vertical angle according to Table 1.
• Set the Pulse Count to ON.
• Mount where animals cannot come within six feet of the detector by climbing on furniture, boxes, or other objects.
• Do not aim the detector at stairways or furniture / objects that can be climbed by an animal.
Note: This unit will provide immunity to false alarms for an individual animal or a group of animals whose total weight
is equal to or less than 40 pounds when the room temperature is above 10° C.
TROUBLESHOOTING
Trouble 1: INTERMITTENT ALARM
Probable Causes:
A. Rapid temperature change. Check for electric or gas heaters,
open flames, electric arcs, etc.
Remedy: Locate source and re-position detector.
B. Drafts causing drapes, light fixtures, display material to move.
Remedy: Eliminate source of motion.
Trouble 2: LED INOPERATIVE DURING WALK TEST
Probable Causes:
A. LED control jumper set to NORMAL.
Remedy: Re-position jumper to TEST position.
B. LED malfunction. Check for broken/shorted leads.
Remedy: Return unit for service.
Trouble 3: DETECTION AREA CHANGES
Probable Causes:
A. Re-positioned furniture or equipment in the protected area.
Remedy: Caution customer about layout changes. Reposition
detector.
B. Mounting surface is unstable. A few degrees of vertical shift can
change range substantially.
Remedy: Mount on secure surface.
Trouble 4: UNIT DOES NOT APPEAR TO BE OPERATING
Probable Cause:
A. Unit is not receiving power.
Remedy: Check for appropriate battery voltage. Install new batteries
if necessary. Be sure to change both batteries.
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT
The user shall not make any changes or modifications to the equipment unless authorized by the installation Instructions or User's Manual.
Unauthorized changes or modifications could void the user's authority to operate the equipment.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS 210 of IC.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any
interference received, including interference that may cause undesired operation.
-3-
LIMITATIONS OF THE PIR MOTION DETECTOR
While the Intrusion Detector is a highly reliable intrusion detection
device, it does not offer guaranteed protection against burglary. Any
Intrusion Detection device is subject to compromise or failure to warn
for a variety of reasons:
• Passive Infrared Motion Detectors can detect intrusion only within the
designed ranges as diagrammed in this installation manual.
• Passive Infrared Motion Detectors do not provide volumetric area
protection. They do create multiple beams of protection, and
intrusion can be detected only in unobstructed areas covered by
those beams.
• Passive Infrared Detectors cannot detect motion or intrusion that
takes place behind walls, ceilings, floors, closed doors, glass
partitions, glass doors, or windows.
• Mechanical tampering, masking, painting, or spraying of any material
on the lenses, windows or any part of the optical system can reduce
the detection ability of the Passive Infrared Motion Detector.
• Passive Infrared Detectors sense changes in temperature; however,
as the ambient temperature of the protected area approaches the
temperature range of 90° to 105°F (32° to 40°C), the detection
performance can decrease.
• This Passive Infrared Detector will not operate without the
appropriate battery installed, or if the battery is weak or improperly
connected (i.e., reversed polarity).
• Passive Infrared Detectors, like other electrical devices, are subject
to component failure. Even though this equipment is designed to last
as long as 10 years, the electronic components in it could fail at any
time.
We have cited some of the most common reasons that a Passive
Infrared Motion Detector can fail to catch intrusion. However, this does
not imply that these are the only reasons, and therefore it is
recommended that weekly testing of this type of unit, in conjunction with
weekly testing of the entire alarm system, be performed to ensure that
the detectors are working properly.
Installing an alarm system may make the owner eligible for a lower
insurance rate, but an alarm system is not a substitute for insurance.
Homeowners, property owners and renters should continue to act
prudently in protecting themselves and continue to insure their lives and
property.
We continue to develop new and improved protection devices. Users of
alarm systems owe it to themselves and their loved ones to learn about
these developments.
LIMITED WARRANTY
Honeywell International Inc., acting through its Security & Custom
Electronics business ("Seller"), 2 Corporate Center Drive, Melville,
NY, 11747, warrants its product(s) to be in conformance with its own
plans and specifications and to be free from defects in materials and
workmanship under normal use and service for 24 months from the
date stamp control on the product(s) or, for product(s) not having a
manufacturer’s date stamp, for 12 months from date of original
purchase unless the installation instructions or catalog sets forth a
shorter period, in which case the shorter period shall apply. Seller's
obligation shall be limited to repairing or replacing, at its option, free
of charge for materials or labor, any product(s) which is proved not in
compliance with Seller's specifications or proves defective in
materials or workmanship under normal use and service. Seller shall
have no obligation under this Limited Warranty or otherwise if the
product(s) is altered or improperly repaired or serviced by anyone
other than Honeywell factory service. Connection of any device(s) to a
communicating bus of a Honeywell security system (e.g., keypad bus,
polling loop) other than those manufactured or approved by
Honeywell shall void this warranty. For warranty service, return
product(s) transportation prepaid, to your local authorized Honeywell
representative.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF
MERCHANTABILITY, OR FITNESS FOR A PARTICULAR
PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL
SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL
OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY
OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY
OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE
LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN
NEGLIGENCE OR FAULT.
Seller does not represent that the product(s) it sells may not be
compromised or circumvented; that the product(s) will prevent any
personal injury or property loss by burglary, robbery, fire or
otherwise; or that the product(s) will in all cases provide adequate
warning or protection. Customer understands that a properly
installed and maintained alarm system may only reduce the risk of a
burglary, robbery, fire, or other events occurring without providing
an alarm, but it is not insurance or a guarantee that such will not
occur or that there will be no personal injury or property loss as a
result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY
FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER
LOSS BASED ON A CLAIM THAT THE PRODUCT(S) FAILED TO
GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE,
WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR
DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR
OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S
MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE
PURCHASE PRICE OF THE PRODUCT(S), WHICH SHALL BE THE
COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER.
This warranty replaces any previous warranties and is the only
warranty made by Seller on this product(s). No increase or alteration,
written or verbal, of the obligations of this Limited Warranty is
authorized.
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright 2007 Honeywell International Inc.
www.honeywell.com/security
ÊN5987-1V2AŠ
N5987-1V2 9/06 Rev. B
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement