installation instructions
INSTALLATION
INSTRUCTIONS
Accessory
Application
Publications No.
FRONT ASHTRAY WITH
CIGARETTE LIGHTER
P/N 08U25-S84-100
2002 ACCORD
2- AND 4-DOOR
AII 22923
Issue Date
AUG 2001
3. Disconnect the negative cable from the battery.
PARTS LIST
Front ashtray with
cigarette lighter
4. Attach a piece of masking tape onto the console
panel below the clock.
CLOCK
Cover bracket
FLAT-TIP
SCREWDRIVER
SHOP MASKING TAPE
TOWEL
Cigarette lighter
harness
CONNECTORS
4 Self-tapping screws
Ground bolt
6 Wire ties
5. Using a flat-tip screwdriver wrapped in a shop
towel, gently pry up on the clock and release the
clips; then disconnect the connectors and remove
the clock.
Relay
6. Remove the console panel (three self-tapping
screws, five retaining clips, two retaining tabs, and
two connectors).
Fuse label
TOOLS REQUIRED
Phillips screwdriver
Ratchet
Diagonal cutters
RETAINING CLIP
RETAINING TAB
RETAINING CLIP
Flat-tip screwdriver
10 mm Socket
Shop towel
INSTALLATION
1. Make sure you have the anti-theft code for radio,
then write down the frequencies for the preset
buttons.
SELFTAPPING
SCREW
2. Set the parking brake.
On A/T Model: Move the shift lever to the “1”
position.
CONSOLE PANEL
 2001 American Honda Motor Co., Inc. – All Rights Reserved
Y0599A
08U25-S84-1000-91
1 of 4
7. Remove the radio assembly (four radio mounting
bolts, and unplug the connector and antenna
lead).
CONNECTOR
9. Remove the left fuse box cover (three retaining
clips and two retaining tabs).
ANTENNA LEAD
RETAINING CLIP
RETAINING
CLIP
LEFT FUSE
BOX COVER
RADIO MOUNTING
BOLTS (Reuse.)
RETAINING TAB
RADIO ASSEMBLY
RETAINING CLIP
8. Remove and discard the front console lower cover
(four retaining clips).
10. Remove the driver’s dashboard lower cover (three
screws and five retaining clips).
RETAINING
CLIP
SCREW
FRONT CONSOLE
LOWER COVER
(Discard.)
SCREW
RETAINING
CLIP
DRIVER’S
DASHBOARD
LOWER COVER
RETAINING
CLIP
SCREW
RETAINING
CLIP
2 of 4
AII 22923 (0108)
 2001 American Honda Motor Co., Inc. – All Rights Reserved
11. Remove the left front side trim (one retaining clip
and four retaining tabs).
RETAINING
CLIP
14. Plug the yellow/red 1-pin connector of the
cigarette lighter harness into the No. 1 terminal of
the fuse box, the red/black 1-pin connector into
the No. 3 terminal, and the white 1-pin connector
into the No. 5 terminal, respectively.
FUSE BOX
YELLOW/RED
LEFT
FRONT
SIDE TRIM
1-PIN
CONNECTOR
RED/BLACK
WHITE
FUSE CASE
RETAINING
TAB
1-PIN
CONNECTOR
FUSE
LABEL
12. Remove the left kick panel (two retaining clips).
15. Attach the fuse label to the fuse case taped to the
cigarette lighter harness.
16. Remove the bolt securing the bottom of the
engine hood opener bracket, and install the relay
there with the same bolt.
GROUND
BOLT
BOLT
(Discard.)
GROUND
CONNECTOR
(Move ground
connector from
the 2:00 o’clock
to the 10:00
o’clock position.)
4-PIN
CONNECTOR
GROUND OF
CIGARETTE
BOLT
LIGHTER
HARNESS
GROUND
TERMINAL
13. Loosen the ground bolt and move the ground
connector from the 2:00 o’clock to the
10:00 o’clock position. Retighten the ground bolt.
RELAY
ENGINE HOOD
OPENER BRACKET
BOLT
17. Remove and discard the bolt securing the top of
the engine hood opener bracket, and attach the
ground terminal of the cigarette lighter harness
there with the ground bolt from the kit.
 2001 American Honda Motor Co., Inc. – All Rights Reserved
AII 22923 (0108)
3 of 4
18. Plug the 4-pin connector of the cigarette lighter
harness into the relay you installed in step 16.
22. Attach the cover bracket with the two self-tapping
screws.
SELF-TAPPING SCREWS
19. Route the 4-pin connector of the cigarette lighter
harness above the steering shaft to the front
console. Secure the harness to the dashboard
support with one wire tie.
CIGARETTE LIGHTER HARNESS
WIRE TIE
COVER
BRACKET
23. Reinstall the driver’s dashboard lower cover.
DASHBOARD
SUPPORT
20. Secure the cigarette lighter harness with the three
wire ties in the areas shown.
CIGARETTE LIGHTER HARNESS
24. Plug the 4-pin connector of the cigarette lighter
harness into the front ashtray with cigarette
lighter; then push the four retaining clips of the
front ashtray with cigarette lighter into the holes in
the dashboard.
CIGARETTE
LIGHTER
HARNESS
VEHICLE
HARNESS
RETAINING CLIP
4-PIN
CONNECTOR
VEHICLE
HARNESS
SELFTAPPING
SCREWS
WIRE TIES
FRONT
ASHTRAY WITH
CIGARETTE
LIGHTER
RETAINING CLIP
21. Continue routing the cigarette lighter harness into
the front console, and secure it with two wire ties.
WIRE TIES
25. Secure the front ashtray with cigarette lighter with
two self-tapping screws.
26. Check that all wire harnesses are routed properly
and all connectors are plugged in.
27. Reinstall all removed parts.
28. Connect the negative cable to the battery.
29. Enter the customer’s radio anti-theft code, and
reset the radio station preset buttons.
30. Reset the clock.
CIGARETTE
LIGHTER HARNESS
4 of 4
31. Check the operation of the cigarette lighter.
AII 22923 (0108)
 2001 American Honda Motor Co., Inc. – All Rights Reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement