user`s manual - Webcollage.net
proform.com
Model No. PFTL13116.1
Serial No.
Write the serial number in the space
above for reference.
Serial Number
Decal
ACTIVATE YOUR
WARRANTY
To register your product and
activate your warranty today,
go to my.proform.com.
CUSTOMER CARE
For service at any time, go to
proformservice.com.
Or call 1-888-533-1333
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–12 p.m. MT
Please do not contact the store.
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
USER’S MANUAL
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
THE CHEST HEART RATE MONITOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
HOW TO USE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
ORDERING REPLACEMENT PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
WARNING DECAL PLACEMENT
This drawing shows the locations of the warning
decals. If a decal is missing or illegible, call
the telephone number on the front cover of
this manual and request a free replacement
decal. Apply the decal in the location shown.
Note: The decals may not be shown at actual size.
PROFORM and IFIT are registered trademarks of ICON Health & Fitness, Inc. App store is a trademark of Apple
Inc., registered in the U.S. and other countries. The BLUETOOTH® word mark and logos are registered
trademarks of Bluetooth SIG, Inc. and are used under license. Google Maps is a trademark of Google Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read
all important precautions and instructions in this manual and all warnings on your treadmill before
using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
12. Wear appropriate exercise clothes while
using the treadmill. Do not wear loose
clothes that could become caught in the
treadmill. Athletic support clothes are recommended for both men and women. Always
wear athletic shoes. Never use the treadmill
with bare feet, wearing only stockings, or in
sandals.
2. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or persons
with pre-existing health problems.
3. The treadmill is not intended for use by
persons with reduced physical, sensory, or
mental capabilities or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use
of the treadmill by someone responsible for
their safety.
13. Plug the power cord into a surge suppressor
(not included), and plug the surge suppressor into an appropriate outlet (see page 20).
To avoid overloading the circuit, do not plug
other electrical devices, except for low-power
devices such as cell phone chargers, into
the surge suppressor or into an outlet on the
same circuit.
4. Use the treadmill only as described in this
manual.
14. Use only a surge suppressor that meets all of
the specifications described on page 20. To
purchase a surge suppressor, see your local
PROFORM dealer, call the telephone number
on the front cover of this manual, or see your
local electronics store.
5. The treadmill is intended for home use only.
Do not use the treadmill in any commercial,
rental, or institutional setting.
6. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
15. Failure to use a properly functioning surge
suppressor could result in damage to the
control system of the treadmill. If the control
system is damaged, the walking belt may
slow, accelerate, or stop unexpectedly, which
may result in a fall and serious injury.
7. Place the treadmill on a level surface, with
at least 8 ft. (2.4 m) of clearance behind it
and 2 ft. (0.6 m) on each side. Do not place
the treadmill on any surface that blocks air
openings. To protect the floor or carpet from
damage, place a mat under the treadmill.
16. Keep the power cord and the surge suppressor away from heated surfaces.
8. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
17. Never move the walking belt while the power
is turned off. Do not operate the treadmill
if the power cord or plug is damaged, or if
the treadmill is not working properly. (See
MAINTENANCE AND TROUBLESHOOTING
on page 30 if the treadmill is not working
properly.)
9. Keep children under age 13 and pets away
from the treadmill at all times.
10. The treadmill should be used only by persons weighing 300 lbs. (136 kg) or less.
18. Read, understand, and test the emergency
stop procedure before using the treadmill
(see HOW TO TURN ON THE POWER on
page 22). Always wear the clip while using the
treadmill.
11. Never allow more than one person on the
treadmill at a time.
3
able to safely lift 45 lbs. (20 kg) to move the
treadmill.
19. Always stand on the foot rails when starting
or stopping the walking belt. Always hold the
handrails while using the treadmill.
26. When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position. Do
not operate the treadmill while it is folded.
20. When a person is walking on the treadmill,
the noise level of the treadmill will increase.
21. Keep fingers, hair, and clothing away from
the moving walking belt.
27. Do not change the incline of the treadmill by
placing objects under the treadmill.
22. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
28. Never insert any object into any opening on
the treadmill.
29. Inspect and properly tighten all parts each
time the treadmill is used.
23. The heart rate monitor is not a medical
device. Various factors, including the user’s
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
30.
DANGER: Always unplug the power
cord immediately after use, before cleaning the treadmill, and before performing the
maintenance and adjustment procedures
described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service representative only.
24. Never leave the treadmill unattended while
it is running. Always remove the key, press
the power switch into the off position (see
the drawing on page 6 for the location of the
power switch), and unplug the power cord
when the treadmill is not in use.
25. Do not attempt to move the treadmill until
it is properly assembled. (See ASSEMBLY
on page 8 and HOW TO FOLD AND MOVE
THE TREADMILL on page 29.) You must be
31. Over exercising may result in serious injury
or death. If you feel faint, if you become short
of breath, or if you experience pain while
exercising, stop immediately and cool down.
SAVE THESE INSTRUCTIONS
4
STANDARD SERVICE PLANS
all
5
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM®
PRO 2000 treadmill. The PRO 2000 treadmill offers an
impressive selection of features designed to make your
workouts at home more effective and enjoyable. And
when you’re not exercising, the unique treadmill can
be folded up, requiring less than half the floor space of
other treadmills.
reading this manual, please see the front cover of this
manual. To help us assist you, please note the product
model number and serial number before contacting us.
The model number and the location of the serial number decal are shown on the front cover of this manual.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after
Tablet Holder
Length: 6 ft. 5 in. (196 cm)
Width: 3 ft. 3 in. (99 cm)
Console
Heart Rate Monitor
Tray
Handrail
Key/Clip
Tray
Upright
Motor Hood
Walking Belt
Power Switch
Foot Rail
Power Cord
Platform Cushion
Idler Roller
Adjustment Screws
6
PART IDENTIFICATION CHART
Use the drawings below to identify small parts used for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key
number is the quantity used for assembly. Note: If a part is not in the hardware kit, check to see whether it is
preattached. Extra parts may be included.
1/4" Star
Washer (77)–2
#8 x 1/2" Silver
Screw (13)–1
#8 x 3/4"
Screw (5)–2
1/4" x 5/8"
Screw (99)–2
5/16" x 3/4"
Screw (1)–4
5/16" Star
Washer (8)–10
#8 x 3/4"
Truss Head
Screw (24)–18
5/16" x 1 1/4"
Screw (29)–6
3/8" x 2 3/4" Screw (23)–4
7
3/8" Star
Washer (25)–8
#10 x 3/4"
Screw (6)–2
M4 x 16mm
Screw (3)–4
3/8" x 1 1/4"
Screw (20)–4
ASSEMBLY
• To hire an authorized service technician to
assemble the treadmill, call 1-800-445-2480.
• Left parts are marked “L” or “Left” and right parts
are marked “R” or “Right.”
• Assembly requires two persons.
• To identify small parts, see page 7.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you finish all assembly steps.
• Assembly requires the following tools:
the included hex key
• After shipping, there may be an oily substance
on the exterior of the treadmill. This is normal. If
there is an oily substance on the treadmill, wipe
it off with a soft cloth and a mild, non-abrasive
cleaner.
one adjustable wrench
one Phillips screwdriver
To avoid damaging parts, do not use power tools.
1. Go to my.proform.com on your computer and
register your product.
1
• activates your warranty
• saves you time if you ever need to contact
Customer Care
• allows us to notify you of upgrades and offers
Note: If you do not have Internet access, call
Customer Care (see the front cover of this
manual) and register your product.
8
2. Make sure that the power cord is unplugged.
2
Remove the tie securing the Upright Wire (83) to
the front of the Base (93).
A
83
83
Next, identify the Right Upright (84). Have a second person hold the Right Upright near the Base
(93).
84
See the inset drawing. Tie the wire tie (A) in
the Right Upright (84) securely around the end
of the Upright Wire (83). Then, insert the Upright
Wire into the lower end of the Right Upright as
you pull the other end of the wire tie through the
Right Upright.
A
84
93
3. Lay the Right Upright (84) near the Base (93).
Press the Grommet (86) into the square hole (B)
in the Right Upright. Make sure not to pinch
the ground wire (C).
3
If there is a screw (D) preattached to the Right
Upright (84), remove and discard it.
Then, attach the ground wire (C) to the Right
Upright (84) with a #8 x 1/2" Silver Screw (13).
93
13
86
C
D
B
84
9
4. Hold the Right Upright (84) against the Base
(93). Make sure not to pinch the Upright Wire
(83).
4
23
Attach the Right Upright (84) with two 3/8" x
2 3/4" Screws (23), two 3/8" x 1 1/4" Screws
(20), and four 3/8" Star Washers (25) as shown;
do not fully tighten the Screws yet.
25
Attach the Left Upright (not shown) in the
same way. Note: There are no wires on the left
side.
23
25
83
93
25
84
20
25
20
5. Identify the Left and Right Upright Covers
(89, 90).
5
Slide the Left Upright Cover (89) onto the Left
Upright (91), and slide the Right Upright Cover
(90) onto the Right Upright (84). Press the
Upright Covers downward; do not snap the
Upright Covers into place yet.
E
2
91
2
84
89
Then, remove and save the four indicated
5/16" x 2" Screws (2).
E
If there is a film (E) covering the decal on
each of the Uprights (84, 91), carefully
remove the film.
90
10
6. Attach the two Handrails (74) to the Right and
Left Uprights (84, 91) with the four 5/16" x 2"
Screws (2) that you removed in step 5 and four
5/16" Star Washers (8); do not fully tighten
the Screws yet. Be careful not to pinch the
Upright Wire (83) on the right side.
6
2
8
74
F
91
Then, remove and discard the two indicated
screws (F).
2
83
8
74
F
84
7. With the help of a second person, set the console assembly (G) onto the Handrails (74). Be
careful not to pinch the wires (H).
7
G
Attach the console assembly (G) to the Handrails
(74) with four 5/16" x 1 1/4" Screws (29) and four
5/16" Star Washers (8); do not fully tighten the
Screws yet.
74
74
8
29
11
H
8
29
8. See the inset drawing. Connect the Upright
Wire (83) to the console wire (H). The connectors should slide together easily and snap
into place. If they do not, turn one connector
and try again. IF YOU DO NOT CONNECT THE
CONNECTORS PROPERLY, THE CONSOLE
MAY BECOME DAMAGED WHEN YOU TURN
ON THE POWER. Then, remove any wire ties
(I) from the Upright Wire.
8
H
83
I
H
83
9. Insert the wires (H) into the top of the Right
Upright (84).
9
Next, locate the Wire Tie (102) included with the
hardware. Insert the Wire Tie through the small
hole in the side of the Right Upright (84). Then,
tighten the Wire Tie around the wires (H), and
cut off the end of the Wire Tie.
H
84
12
102
10. IMPORTANT: To avoid damaging the Pulse
Bar (80), do not use power tools, and do not
overtighten the #10 x 3/4" Screws (6) or the
1/4" x 5/8" Screws (99).
10
Tighten two 1/4" x 5/8" Screws (99) with two 1/4"
Star Washers (77), and two #10 x 3/4" Screws
(6), into the Pulse Crossbar (80); start all four
Screws, and then tighten them.
6
80
Then, tighten the four 5/16" x 1 1/4" Screws
(29).
29
77
99
6
29
77
99
11. Set the Left Handrail Top Cover (73) on the left
Handrail (74). Start two #8 x 3/4" Truss Head
Screws (24) and one #8 x 3/4" Screw (5) into the
bottom of the Left Handrail Top Cover. Note: The
#8 x 3/4" Truss Head Screws have flatter heads
than the #8 x 3/4" Screws. Then, tighten all three
Screws. Be careful not to overtighten the
Screws.
11
73
Attach the Right Handrail Top Cover (81) to
the right Handrail (74) as described above.
74 24
5
81
24
74
24
13
5
12. Attach the Left Handrail Bottom Cover (75) to the
left Handrail (74) with two #8 x 3/4" Truss Head
Screws (24); start both Truss Head Screws,
and then tighten them. Be careful not to overtighten the Truss Head Screws.
12
Attach the Right Handrail Bottom Cover (82)
to the right Handrail (74) as described above.
74
75
24
74
82
13. Identify the Left and Right Trays (94, 32). Attach
the Trays to the console assembly (G) with six
#8 x 3/4" Truss Head Screws (24); start all six
Truss Head Screws and then tighten them.
Do not overtighten the Truss Head Screws.
24
13
G
32
94
24
24
14
24
24
14. Carefully slide the Upright Crossbar (76)
between the Right and Left Uprights (84, 91).
Attach the Upright Crossbar with four 5/16" x
3/4" Screws (1); start all four Screws, and then
tighten them.
14
91
84
76
1
1
15. Attach the Tray (97) to the Upright Crossbar (76)
with four #8 x 3/4" Truss Head Screws (24); start
all four Truss Head Screws, and then tighten
them.
15
97
24
15
76
24
16. Raise the Frame (52) to the upright position.
IMPORTANT: Have a second person hold the
Frame until step 18 is completed.
16
52
J
K
Orient the Latch Crossbar (78) as shown. Make
sure that the “This side toward belt” sticker
(J) is facing the treadmill.
78
K
Attach the Latch Crossbar (78) to the brackets
(K) on the Frame (52) with the two 5/16" x 1 1/4"
Screws (29) and two 5/16" Star Washers (8).
8
8
29
29
17. Remove the 5/16" Nut (9) and the 5/16" x 1 3/4"
Bolt (7) from the bracket on the Base (93).
17
Next, orient the Storage Latch (56) as shown.
L
Attach the lower end of the Storage Latch (56)
to the bracket on the Base (93) with the 5/16" x
1 3/4" Bolt (7) and the 5/16" Nut (9).
56
Then, raise the Storage Latch (56) to a vertical
position, and remove the tie (L).
9
93
16
7
18. Remove the 5/16" Nut (9) and the 5/16" x 2 1/4"
Bolt (4) from the bracket on the Latch Crossbar
(78).
18
9
M
Align the upper end of the Storage Latch (56)
with the bracket on the Frame (52), and insert
the 5/16" x 2 1/4" Bolt (4) through the bracket
and the Storage Latch. This will push a spacer
(M) out of the Storage Latch; discard the
spacer.
78
4
56
52
Next, tighten the 5/16" Nut (9) onto the 5/16" x
2 1/4" Bolt (4). Do not overtighten the Nut; the
Storage Latch (56) must be able to pivot.
Then, lower the Frame (52) (see HOW TO
LOWER THE TREADMILL FOR USE on page 29).
19. Firmly tighten the four 3/8" x 2 3/4" Screws (23)
and the four 3/8" x 1 1/4" Screws (20).
19
Next, slide and the Left and Right Upright Covers
(89, 90) down until they snap into place.
89
23
90
23
23
20
17
20
20. Attach the Tablet Holder (100) to the console
assembly (G) with four M4 x 16mm Screws (3);
start all four Screws, and then tighten them.
Do not overtighten the Screws.
20
100
3
3
G
21. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of plastic
on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. To
avoid damage to the console, keep the treadmill out of direct sunlight. Keep the included hex keys in a secure
place; one of the hex keys is used to adjust the walking belt (see pages 31 and 32). Note: Extra parts may be
included.
18
THE CHEST HEART RATE MONITOR
HOW TO PUT ON THE HEART RATE MONITOR
• Store the heart rate monitor in a warm, dry place. Do
not store the heart rate monitor in a plastic bag or
other container that may trap moisture.
If the heart rate monitor looks like the one shown
in drawing 1, press the transmitter (A) onto the snap
fasteners on the chest strap (B). If the heart rate
monitor looks like the one shown in drawing 2,
insert the tab (C) on one end of the chest strap (D) into
one end of the transmitter (E). Then, press the end of
the transmitter under the buckle (F) on the chest strap;
the tab should be flush with the transmitter.
1
2
C
• Do not expose the heart rate monitor to direct sunlight for extended periods of time, and do not expose
it to temperatures above 122°F (50°C) or below 14°F
(-10°C).
• Do not excessively bend or stretch the heart rate
monitor when using or storing it.
• To clean the transmitter, use a damp cloth and a
small amount of mild soap. Then, wipe the transmitter with a damp cloth and thoroughly dry it with a soft
towel. Never use alcohol, abrasives, or chemicals
to clean the transmitter. Hand wash and air dry the
chest strap.
D
B
A
E
F
TROUBLESHOOTING
Next, wrap the heart
rate monitor around
your chest in the location shown; the heart
rate monitor must be
under your clothes,
tight against your skin.
Make sure that the logo
is right-side-up. Then, attach the other end of the chest
strap. Adjust the length of the chest strap, if necessary.
• If the heart rate monitor does not function when positioned as described at the left, move it slightly lower
or higher on your chest.
• If heart rate readings are not displayed until you
begin perspiring, re-wet the electrode areas.
• For the console to display heart rate readings, you
must be within arm’s length of the console.
• If there is a battery cover on the back of the transmitter, replace the battery with a new battery of the
same type.
Next, pull the transmitter and the chest
G
strap away from your
body a few inches
and locate the two
electrode areas (G).
Using saliva or contact lens solution, wet the electrode areas. Then, return
the transmitter and the chest strap to a position against
your chest.
• The heart rate monitor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical conditions such as premature ventricular contractions
(pvcs), tachycardia bursts, and arrhythmia.
• The operation of the heart rate monitor can be
affected by magnetic interference from high power
lines or other sources. If you suspect that magnetic
interference is causing a problem, try relocating the
fitness equipment.
CARE AND MAINTENANCE
• Thoroughly dry the electrode areas with a soft towel
after each use. Moisture may keep the heart rate
monitor activated, shortening the life of the battery.
19
HOW TO USE THE TREADMILL
HOW TO CONNECT THE POWER CORD
more amps. To avoid overloading the circuit, do
not plug other electrical devices, except for lowpower devices such as cell phone chargers, into
the surge suppressor or into an outlet on the same
circuit. IMPORTANT: If the treadmill is connected to
an AFCI-equipped outlet and your circuit breaker
trips repeatedly when the treadmill is used, see the
front cover of this manual to purchase an arc filter.
Use a Surge Suppressor
Your treadmill, like other electronic equipment, can be
damaged by sudden voltage changes in your home’s
power. Voltage surges, spikes, and noise interference can result from weather conditions or from other
appliances being turned on or off. To decrease the
risk of damaging the treadmill, always use a surge
suppressor with the treadmill. To purchase a surge
suppressor, see precaution 14 on page 3.
1
Grounded Outlet
Grounding Pin
Use only a surge suppressor that is UL 1449 listed as a
transient voltage surge suppressor (TVSS). The surge
suppressor must have a UL suppressed voltage rating
of 400 volts or less and a minimum surge dissipation of
450 joules. The surge suppressor must also be electrically rated for 120 volts AC and 15 amps. There must
be a monitoring light on the surge suppressor to indicate whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill
and serious injury to users.
Grounding Pin
Surge
Suppressor
Plug in the Power Cord
A temporary
adapter may
be used to
connect the
surge suppressor to
a 2-pole
receptacle
if a properly
grounded
outlet is not
available.
The treadmill must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. The treadmill power cord has a plug with a
grounding pin (see drawing 1 on this page).
DANGER: Improper connection
of the power cord increases the risk of electric shock. Do not modify the plug—if it will
not fit an outlet, have a proper outlet installed
by a qualified electrician. If you are unsure
whether the treadmill is properly grounded,
contact a qualified electrician.
2
2-pole Receptacle
Adapter
Lug
Metal
Screw
The lug or wire extending from the adapter must
be connected with a metal screw to a permanent
ground such as a properly grounded outlet box cover.
Some 2-pole receptacle outlet box covers are not
grounded. Before using an adapter, contact a qualified electrician to determine whether the outlet box
cover is grounded. The temporary adapter should
be used only until a properly grounded outlet can
be installed by a qualified electrician.
Plug the power cord into a surge suppressor, and plug
the surge suppressor into an appropriate outlet that is
properly installed and grounded in accordance with all
local codes and ordinances. The outlet must be on a
nominal 120-volt circuit capable of carrying 15 or
20
CONSOLE
DIAGRAM
FEATURES OF THE CONSOLE
To turn on the power, see page 22. To use the manual mode, see page 22. To use an onboard workout,
see page 24. To connect your tablet to the console,
see page 26. To connect your heart rate monitor to
the console, see page 26. To use the settings mode,
see page 27. To use the sound system, see page 27.
To use the tablet holder, see page 27.
The treadmill console offers a selection of features
designed to make your workouts more effective and
enjoyable. When you use the manual mode, you can
change the speed and incline of the treadmill with the
touch of a button. As you exercise, the console will display instant exercise feedback. You can even measure
your heart rate using the handgrip heart rate monitor or
the chest heart rate monitor.
Note: The console can display speed and distance
in either miles or kilometers. To change which unit of
measurement is selected, press the Standard/Metric
button. For simplicity, all instructions in this section
refer to miles.
In addition, the console features a selection of onboard
workouts. Each workout automatically controls the
speed and incline of the treadmill as it guides you
through an effective exercise session.
IMPORTANT: If there are sheets of plastic on the
console, remove the plastic. To prevent damage
to the walking platform, wear clean athletic shoes
while using the treadmill. The first time you use
the treadmill, observe the alignment of the walking
belt, and center the walking belt if necessary (see
page 31).
You can also connect your tablet to the console and use
the iFit® Bluetooth Tablet app to record and track your
workout information.
You can even listen to your favorite workout music or
audio books with the console’s sound system while you
exercise.
21
HOW TO TURN ON THE POWER
HOW TO USE THE MANUAL MODE
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room temperature before you turn on the power. If you do
not do this, you may damage the console displays
or other electrical components.
1. Insert the key into the console.
Plug in the power cord (see
page 20). Next, locate the
power switch on the treadmill frame near the power
cord. Press the power
switch into the reset
position.
See HOW TO TURN ON THE POWER at the left.
2. Select the manual mode.
If the manual mode is not selected, press the
Manual button on the console.
3. Start the walking belt.
Reset
To start the walking belt, press the Run button or
one of the numbered speed buttons.
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key and slide the clip onto the
waistband of your clothes. Then, insert the key into
the console. After a moment, the displays will light.
IMPORTANT: In an emergency, the key can be
pulled from the console, causing the walking belt
to slow to a stop. Test the clip by carefully taking
a few steps backward; if the key is not pulled from
the console, adjust the position of the clip.
If you press the Run button the walking belt will
begin to move at 1 mph. As you exercise, change
the speed of the walking belt as desired by pressing the Speed increase and decrease buttons.
Each time you press one of the buttons, the speed
setting will change by 0.1 mph; if you hold down
the button, the speed setting will change in increments of 0.5 mph. Note: After you press the button,
it may take a moment for the walking belt to reach
the selected speed setting.
IMPORTANT: Before
you use the treadmill,
Key
take the following
steps to ensure that
the console shows
the correct incline
level of the treadmill:
First, press the Incline
increase button once.
Next, press either
Clip
the Incline decrease
button or the lowest
numbered incline
button to set the treadmill to its lowest setting.
When the frame stops moving, the treadmill is
ready for use.
If you press one of the numbered speed buttons,
the walking belt will gradually change speed until
it reaches the selected speed setting. To select a
speed setting that includes a decimal—such as 3.5
mph—press two numbered buttons in succession.
For example, to select a speed setting of 3.5 mph,
press the 3 button and then immediately press the
5 button. Note: This feature will not function if the
console is set to metric units.
To stop the walking belt, press the Stop button. The
time will begin to flash in the display. To restart the
walking belt, press the Run button.
22
4. Change the incline of the treadmill as desired.
The My Trail tab will show a track that represents
1/4 mile (400 m). As you exercise, the flashing
rectangle will show your progress. The My Trail tab
will also show the number of laps you complete.
To change the incline of the treadmill, press the
Incline increase or decrease button or one of the
numbered incline buttons. Each time you press one
of the buttons, the treadmill will gradually adjust to
the selected incline setting.
The Calorie tab will show the approximate amount
of calories you have burned. The height of each
segment represents the amount of calories burned
during that segment. When the Calorie tab is
selected, the calorie display will show the approximate number of calories burned per hour.
5. Follow your progress with the displays.
As you walk or run on the treadmill, the display can
show the following workout information:
As you exercise, the workout intensity level bar
will indicate the approximate intensity level of your
exercise.
• The elapsed time
• The distance that you have walked or run
• The workout intensity bar
• The approximate number of calories you have
burned
• The incline level of the treadmill
Press the Home button to return to the default
menu (see THE SETTINGS MODE on page 27
to set the default menu). If necessary, press the
Home button again.
• The number of vertical feet you have climbed
• The speed of the walking belt
To reset the displays, press the Stop button
repeatedly.
• Your heart rate (see step 6 on page 24)
• The matrix
The Incline tab will show a profile of the incline settings of the workout. A new segment will appear at
the end of each minute. The Speed tab will show a
profile of the speed settings of the workout.
23
6. Measure your heart rate if desired.
8. When you are finished exercising, remove the
key from the console.
Note: If you use the handgrip heart rate monitor and the chest heart rate monitor at the same
time, the console will not display your heart
rate accurately. For information about the chest
heart rate monitor, see page 19. Note: The console
is compatible with BLUETOOTH® Smart heart rate
monitors.
Before using
the handgrip
heart rate monitor, remove the
sheets of plastic
from the metal
contacts on the
pulse bar. In addition, make sure
that your hands
are clean.
When you are finished using the treadmill, step
onto the foot rails, press the Stop button, then
press the End/Summary button. Next, adjust the
incline of the treadmill to zero. The incline must
be at zero or you may damage the treadmill
when you fold it to the storage position. Next,
remove the key from the console and put it in a
secure place.
Then, press the power switch into the off position
and unplug the power cord. IMPORTANT: If you
do not do this, the treadmill’s electrical components may wear prematurely.
Contacts
HOW TO USE AN ONBOARD WORKOUT
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page 22.
To measure your heart rate, stand on the foot
rails and hold the pulse bar with your palms on
the metal contacts; avoid moving your hands.
When your pulse is detected, your heart rate will be
shown. For the most accurate heart rate reading, continue to hold the metal contacts for
about 15 seconds.
2. Select an onboard workout.
To select an onboard workout, press the Fitness
Apps button repeatedly until the desired workout
appears in the display.
When you select an onboard workout, the display
will show the duration of the workout and the name
of the workout. In addition, a profile of the speed
settings of the workout will appear in the matrix.
If you select a calorie workout, the approximate
number of calories you will burn will appear in the
calorie window.
7. Turn on the fan if desired.
The fan features several
speed settings. Press the
fan buttons repeatedly to
select a fan speed or to
turn on or turn off the fan.
3. Start the workout.
Press the Run button to start the workout. A
moment after you press the button, the treadmill
will automatically adjust to the first speed and
incline settings of the workout. Hold the handrails
and begin walking.
24
Each workout is divided into segments. One speed
setting and one incline setting are programmed for
each segment. Note: The same speed setting and/
or incline setting may be programmed for consecutive segments.
If the speed or incline setting is too high or too low
at any time during the workout, you can manually override the setting by pressing the Speed or
Incline buttons; however, when the next segment of the workout begins, the treadmill will
automatically adjust to the speed and incline
settings for the next segment.
During the
workout, the
profiles on the
speed and
incline tabs
Current Segment
will show your
progress. The
flashing segment of the profile represents the current segment
of the workout. The height of the flashing segment
indicates the speed or incline setting for the current
segment. At the end of each segment, a series of
tones will sound and the next segment of the profile
will begin to flash. If a different speed and/or incline
setting is programmed for the next segment, the
speed and/or incline setting will flash in the display
to alert you and the treadmill will automatically
adjust to the new speed and/or incline setting.
To stop the workout at any time, press the Stop
button. The time will begin to flash in the display.
To resume the workout, press the Run button. The
walking belt will begin to move at 1 mph. When the
next segment of the workout begins, the treadmill
will automatically adjust to the speed and incline
settings for the next segment.
4. Follow your progress with the displays.
See step 5 on page 23. If you select an onboard
workout, the display will show the time remaining or
the calories remaining instead of the elapsed time.
5. Measure your heart rate if desired.
See step 6 on page 24.
The workout will continue in this way until the last
segment of the profile flashes in the display and the
last segment ends. The walking belt will then slow
to a stop.
6. Turn on the fan if desired.
See step 7 on page 24.
Note: The calorie goal is an estimate of the
number of calories that you will burn during
the workout. The actual number of calories
that you burn will depend on various factors
such as your weight. In addition, if you manually change the speed or incline of the treadmill
during the workout, the number of calories you
burn will be affected.
7. When you are finished exercising, remove the
key from the console.
See step 8 on page 24.
25
HOW TO CONNECT YOUR TABLET TO THE
CONSOLE
5. Disconnect your tablet from the console if
desired.
The console supports BLUETOOTH connections to
tablets via the iFit Bluetooth Tablet app and to compatible heart rate monitors. Note: Other BLUETOOTH
connections are not supported.
To disconnect your tablet from the console, first
select the disconnect option in the iFit Bluetooth
Tablet app. Then, press and hold the iFit Sync
button on the console until the LED on the console
turns solid green.
1. Download and install the iFit Bluetooth Tablet
app on your tablet.
Note: All BLUETOOTH connections between
the console and other devices (including any
tablets, heart rate monitors, and so forth) will be
disconnected.
On your iOS® or Android™ tablet, open the App
Store℠ or the Google Play™ store, search for
the free iFit Bluetooth Tablet app, and then install
the app on your tablet. Make sure that the
BLUETOOTH option is enabled on your tablet.
HOW TO CONNECT YOUR HEART RATE MONITOR
TO THE CONSOLE
Then, open the iFit Bluetooth Tablet app and follow
the instructions to set up an iFit account and customize settings.
The console is compatible with all BLUETOOTH Smart
heart rate monitors.
2. Connect your heart rate monitor to the console
if desired.
To connect your BLUETOOTH Smart heart rate monitor to the console, press the iFit Sync button on the
console; the console pairing number will appear in the
display. When a connection is established, the LED on
the console will flash red twice.
If you are connecting both your heart rate monitor
and your tablet to the console, you must connect
your heart rate monitor before you connect
your tablet. See HOW TO CONNECT YOUR
HEART RATE MONITOR TO THE CONSOLE at
the right.
Note: If there is more than one compatible heart rate
monitor near the console, the console will connect to
the heart rate monitor with the strongest signal.
3. Connect your tablet to the console.
To disconnect your heart rate monitor from the console,
press and hold the iFit Sync button on the console until
the LED on the console turns solid green.
Press the iFit Sync button on the console; the
console pairing number will appear in the display.
Then, follow the instructions in the iFit Bluetooth
Tablet app to connect your tablet to the console.
Note: All BLUETOOTH connections between the
console and other devices (including any tablets, heart
rate monitors, and so forth) will be disconnected.
When a connection is established, the LED on the
console will turn solid blue.
4. Record and track your workout information.
Follow the instructions in the iFit Bluetooth Tablet
app to record and track your workout information.
26
THE SETTINGS MODE
HOW TO USE THE SOUND SYSTEM
The console features an information mode that keeps
track of treadmill information and allows you to personalize console settings.
To play music or audio books through the console
sound system while you exercise, plug a 3.5 mm male
to 3.5 mm male audio cable (not included) into the
jack on the console and into a jack on your personal
audio player; make sure that the audio cable is fully
plugged in. Note: To purchase an audio cable, see
your local electronics store.
1. Select the information mode.
To select the settings mode, press the Settings
button. When the settings mode is selected, the
display will show the total number of hours that
the treadmill has been used and the total number
of miles (or kilometers) that the walking belt has
moved.
Next, press the play button on
your personal audio player.
Adjust the volume level using
the volume increase and
decrease buttons on the console or the volume control on
your personal audio player.
2. Select the optional screens.
While the information mode is selected, the matrix
will display several optional screens. Press the
increase button next to the Enter button to select
each of the following screens:
HOW TO USE THE TABLET HOLDER
IMPORTANT: The tablet holder is designed for use
with most full-size tablets. Do not place any other
electronic device or object in the tablet holder.
INCLINE CALIBRATION—To calibrate the incline
system of the treadmill, press the Incline increase
or decrease buttons. The treadmill will automatically rise to the maximum incline level and then
return to the minimum level.
To insert a tablet into the tablet holder, set the bottom
edge of the tablet in the tray. Then, pull the clip over
the top edge of the tablet. Make sure that the tablet
is firmly secured in the tablet holder. Reverse these
actions to remove the tablet from the tablet holder.
CONTRAST LVL—Press the Incline increase and
decrease buttons to adjust the contrast level of the
display.
Press the decrease button next to the Enter button
to return to the previous screen.
Tablet Holder
3. Exit the settings mode.
To exit the settings mode, remove the key from the
console.
27
FCC INFORMATION
This console has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION: To assure continued compliance, use only shielded interface cables when connecting to
computer or peripheral devices. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
IMPORTANT: To satisfy exposure compliance requirements, the antenna and transmitter in the console
must be at least 8 in. (20 cm) from all persons and must not be near or connected to any other antenna or
transmitter.
Note: The console contains either FCC ID: OMCBBICON14 or FCC ID: OMCBMD1.
28
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL
HOW TO MOVE THE TREADMILL
To avoid damaging the treadmill, adjust the incline
to zero before you fold the treadmill. Then, remove
the key and unplug the power cord. CAUTION: You
must be able to safely lift 45 lbs. (20 kg) to raise,
lower, or move the treadmill.
Before moving the treadmill, fold it as described at the
left. CAUTION: Make sure that the storage latch is
locked in the storage position. Moving the treadmill
may require two people.
1. Hold the frame and one of the handrails, and place
one foot against a wheel.
1. Hold the metal frame firmly in the location shown
by the arrow below. CAUTION: Do not hold the
frame by the plastic foot rails. Bend your legs
and keep your back straight.
1
Frame
1
Handrail
Frame
Wheel
2. Pull back on the handrail until the treadmill will roll
on the wheels, and carefully move it to the desired
location. CAUTION: Do not move the treadmill without tipping it back, do not pull on the
frame, and do not move the treadmill over an
uneven surface.
2. Raise the frame until the storage latch locks in the
storage position. CAUTION: Make sure that the
storage latch locks.
2
3. Place one foot against a wheel, and carefully lower
the treadmill.
Frame
HOW TO LOWER THE TREADMILL FOR USE
Storage
Latch
1. Push the upper end of the
frame forward, and gently
press the upper part of
the storage latch with your
foot at the same time.
2. While pressing the storage latch with your foot,
pull the upper end of the
frame toward yourself.
To protect the floor or carpet, place a mat under the
treadmill. Keep the treadmill out of direct sunlight.
Do not leave the treadmill in the storage position in
temperatures above 85°F (30°C).
3. Step back and let the
frame lower to the floor.
29
1
2
MAINTENANCE AND TROUBLESHOOTING
MAINTENANCE
b. After the power cord has been plugged in, make
sure that the key is inserted into the console.
Regular maintenance is important for optimal performance and to reduce wear. Inspect and properly tighten
all parts each time the treadmill is used. Replace any
worn parts immediately.
c. Check the power switch located on the treadmill
frame near the power cord. If the switch protrudes
as shown, the switch has tripped. To reset the
power switch, wait for five minutes and then press
the switch back in.
Regularly clean the treadmill and keep the walking
belt clean and dry. First, press the power switch into
the off position and unplug the power cord. Wipe
exterior parts of the treadmill with a damp cloth and a
small amount of mild soap. IMPORTANT: Do not spray
liquids directly onto the treadmill. To avoid damage
to the console, keep liquids away from the console.
Then, thoroughly dry the treadmill with a soft towel.
c
Tripped
Reset
TROUBLESHOOTING
SYMPTOM: The power turns off during use
Most treadmill problems can be solved by following
the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual.
a. Check the power switch (see the drawing above).
If the switch has tripped, wait for five minutes and
then press the switch back in.
b. Make sure that the power cord is plugged in. If the
power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
SYMPTOM: The power does not turn on
a. Make sure that the power cord is plugged into a
surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see
page 20). Use only a surge suppressor that meets
all of the specifications described on page 20.
IMPORTANT: If the treadmill is connected to an
AFCI-equipped outlet and your circuit breaker
trips repeatedly when the treadmill is used, see
the front cover of this manual to purchase an
arc filter.
c. Remove the key from the console, and then
reinsert it.
d. If the treadmill still will not run, please see the front
cover of this manual.
30
c. Your treadmill features a walking belt coated with
high-performance lubricant. IMPORTANT: Never
apply silicone spray or other substances to
the walking belt or the walking platform unless
instructed to do so by an authorized service
representative. Such substances may deteriorate the walking belt and cause excessive wear.
If you suspect that the walking belt needs more
lubricant, see the front cover of this manual.
SYMPTOM: The incline of the treadmill does not
change correctly
a. Calibrate the incline system of the treadmill (see
THE SETTINGS MODE on page 27).
SYMPTOM: The walking belt slows when walked on
a. Use only a surge suppressor that meets all of the
specifications described on page 20.
d. If the walking belt still slows when walked on, see
the front cover of this manual.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may
become damaged. Remove the key and UNPLUG
THE POWER CORD. Using the hex key, turn both
idler roller screws counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and walk on
the treadmill for a few minutes. Repeat until the
walking belt is properly tightened.
SYMPTOM: The walking belt is off-center or slips
when walked on
a. If the walking belt is off-center, first remove the
key and UNPLUG THE POWER CORD. If the
walking belt has shifted to the left, use the hex
key to turn the left idler roller screw clockwise 1/2
of a turn; if the walking belt has shifted to the
right, turn the left idler roller screw counterclockwise 1/2 of a turn. Be careful not to overtighten the
walking belt. Then, plug in the power cord, insert
the key, and walk on the treadmill for a few minutes. Repeat until the walking belt is centered.
b
2–3 in.
a
Idler Roller Screws
31
b. If the walking belt slips when walked on, first
remove the key and UNPLUG THE POWER
CORD. Using the hex key, turn both idler roller
screws clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able
to lift each edge of the walking belt 2 to 3 in. (5 to
7 cm) off the walking platform. Be careful to keep
the walking belt centered. Then, plug in the power
cord, insert the key, and walk on the treadmill for a
few minutes. Repeat until the walking belt is properly tightened.
SYMPTOM: The tablet holder does not stay in place
a. Rotate the tablet holder backwards. Then, tighten
the indicated screw slightly until the tablet holder
stays in place when it is rotated to the desired
position.
a
b
Screw
32
Tablet
Holder
EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The heart rate monitor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming Up—Start with 5 to 10 minutes of stretching and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise; never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exercise, you may complete up to five workouts each week,
if desired. Remember, the key to success is to make
exercise a regular and enjoyable part of your everyday
life.
33
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach down
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times. Stretches: Hamstrings, back of knees and back.
1
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back and
groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your hands
against a wall. Keep your back leg straight and your back foot flat on
the floor. Bend your front leg, lean forward and move your hips toward
the wall. Hold for 15 counts, then relax. Repeat 3 times for each leg.
To cause further stretching of the achilles tendons, bend your back leg
as well. Stretches: Calves, achilles tendons and ankles.
3
4. Quadriceps Stretch
4
With one hand against a wall for balance, reach back and grasp one
foot with your other hand. Bring your heel as close to your buttocks as
possible. Hold for 15 counts, then relax. Repeat 3 times for each leg.
Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
34
5
PART LIST
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
4
4
4
1
70
2
5
10
6
20
4
3
1
1
1
8
2
4
2
4
1
2
4
18
8
2
4
2
6
1
4
1
1
2
6
5
4
1
1
1
1
1
2
1
4
2
2
1
2
1
1
1
4
1
1
Model No. PFTL13116.1 R0417A
Description
Key No. Qty.
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
*
5/16" x 3/4" Screw
5/16" x 2" Screw
M4 x 16mm Screw
5/16" x 2 1/4" Bolt
#8 x 3/4" Screw
#10 x 3/4" Screw
5/16" x 1 3/4" Screw
5/16" Star Washer
5/16" Nut
#8 x 3/4" Tek Screw
#8 x 1/2" Pan Head Screw
1/4" x 2 1/2" Screw
#8 x 1/2" Silver Screw
3/8" x 1 1/2" Bolt
3/8" x 2" Bolt
#8 x 3/4" Washer Head Screw
#8 x 1 3/4" Screw
#8 Belt Guide Screw
5/16" Motor Bolt
3/8" x 1 1/4" Screw
1/4" Nut
3/8" x 1 3/4" Bolt
3/8" x 2 3/4" Screw
#8 x 3/4" Truss Head Screw
3/8" Star Washer
1/2" x 2 1/4" Bolt
Rubber Cushion
3/8" x 1" Screw
5/16" x 1 1/4" Screw
Console Base
5/16" Flat Washer
Right Tray
Console Frame
1/2" Nut
3/8" Nut
Hood Clip
Cushion
Warning Decal
Walking Platform
Walking Belt
Left Foot Rail
Right Foot Rail
Belt Guide
Left Frame Cover
3/8" Bushing
3/8" Thrust Washer
1/2" Thrust Washer
Controller
#8 Star Washer
Controller Bracket
Drive Roller/Pulley
Frame
Tie
Drive Motor
Motor Belt
1
1
9
1
1
1
1
2
2
1
1
2
2
1
1
1
1
1
2
1
1
2
1
1
1
1
1
1
1
3
2
2
1
1
1
1
2
1
1
2
1
1
1
2
1
4
3
1
4
1
1
1
2
–
Description
Storage Latch
Right Frame Cover
#8 x 1/2" Screw
Idler Roller
Left Rear Cap
Right Rear Cap
Motor Hood
Incline Frame Spacer
Frame Spacer
Incline Frame
Incline Motor
Incline Motor Spacer
Hood Mount
Power Cord
Power Cord Grommet
Power Switch
Belly Pan
Left Handrail Top Cover
Handrail
Left Handrail Bottom Cover
Upright Crossbar
1/4" Star Washer
Latch Crossbar
Key/Clip
Pulse Crossbar
Right Handrail Top Cover
Right Handrail Bottom Cover
Upright Wire
Right Upright
Caution Decal
Grommet
1/2" Bushing
Chest Heart Rate Monitor
Left Upright Cover
Right Upright Cover
Left Upright
Rear Wheel
Base
Left Tray
Fan
Console
Tray
Controller Clamp
1/4" x 5/8" Screw
Tablet Holder
Base Pad
Wire Tie
Console Ground Wire
1/4" x 1" Screw
Pulse Bar
Fan Cover
Fan Housing
Console Clamp
User’s Manual
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
35
36
5
60
12
10
31
27
7
38
9
10
16
5
5
61
16
104
12
10
37
8
59
11
5
7
29
16
10
27
31
9
41
104
43
44
10
16
18
10
42
16
57
104
26
10
16
40
10
9
7
104
8
29
39
4
56
37
10
11
5
16
17
55
37
19
18
10
11
21
5
48
58
16
54
43
10
9
78
27
31
9
7
51 12
17
5
53
50
7
26
10
58
52
98 49 58
EXPLODED DRAWING A
Model No. PFTL13116.1 R0417A
EXPLODED DRAWING B
Model No. PFTL13116.1 R0417A
5
5
36
5
36
5
36
36
62
5
28
45
36
15
63
5
66
87
64
35
47
34
68
14
63
45
5
5
65
35
68
67
5
5
28
34
47
64
87
5
71
5
72
69
5
5
5
37
70
58
EXPLODED DRAWING C
Model No. PFTL13116.1 R0417A
105
97
73
6
5
80
5
58
2
8
8
5
29
81
1
5
77
74
24
6
99
24
5
24
8
2
24
75
8
24
1
29
83
76
91
74
77
24
1
24
99
24
23
82
20
45
25
20
46
35
85
25
101
10
93
22
84
24
25
35
101
46
45
85
10
85
23
23
25
25
25
86
92
20
13
35
89
101
10
101
25
35
10
90
22
92
38
20
EXPLODED DRAWING D
Model No. PFTL13116.1 R0417A
100
88
24
96
3
24
30
5
94
5
5
5
24
58
5
24
103
33
108
107
5
24
5
5
5 108
5
32
5
95
5
5
5
5
5
95
79
5
5
5
5
102
5
106
5
39
24
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
LIMITED WARRANTY
IMPORTANT: To protect your fitness equipment with an extended service plan, see page 6.
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The frame and the drive motor are warranted for the
lifetime of the original purchaser (customer). Parts and electronics are warranted for five (5) years from the
date of purchase. Labor is warranted for two (2) years from the date of purchase.
This warranty extends only to the original purchaser (customer) and is not transferrable. ICON’s obligation under this warranty is limited to repairing or replacing, at ICON’s option, the product through one of
its authorized service providers. All repairs for which warranty claims are made must be preauthorized by
ICON. If replacement parts are shipped while the product is under warranty, the customer will be responsible for a minimal handling charge. For in-home service, the customer may be responsible for a minimal
trip charge. This warranty does not extend to freight damage to the product. This warranty will automatically be voided by the following conditions: (1) if the product is used as a store display model, (2) if the
product is purchased or transported outside the USA, (3) if all instructions and warnings in this manual are
not followed, (4) if the product is abused or improperly or abnormally used, or (5) if the product is used for
commercial or rental purposes. No other warranty beyond that specifically set forth above is authorized
by ICON.
ICON is not responsible or liable for the following damages: (1) indirect, special, or consequential damages arising out of or in connection with the use or performance of the product; (2) damages with respect
to any economic loss, loss of property, loss of revenues or profits, loss of enjoyment or use, or costs of
removal or installation; or (3) other consequential damages of any kind. Some states do not allow the
exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not
apply to the customer.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or fitness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to the customer. This warranty provides specific legal rights; the customer
may have other rights that vary from state to state.
For warranty service, please call the telephone number on the front cover of this manual. Please be prepared to provide the model number and serial number of the product (see the front cover of this manual).
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 391560 R0417A
Printed in China © 2017 ICON Health & Fitness, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement