SPEAKMAN COMPANY
SE-565 Installation, Maintenance & Operation Instructions
EYESAVER
® EYEWASH
DESCRIPTION
Deck mounted emergency eyewash. Supplied with stainless steel bowl, stay-open full flow ball valve; activated by stainless steel trigger bar; adjustable volume regulator, aerated spray outlets with individual adjustments for maximum performance, and mounted on counter tops up to 2” thick.
SPECIFICATIONS
BOWL: 300 Series Stainless Steel.
SPRAY HEADS: (2) Brass, Chrome-Plated, Aerated.
VALVE: 1/2” NPT Female Brass, Chrome-Plated.
ACTIVATOR: Stainless Steel Trigger Bar.
INLET: 1/2” NPT Female.
SHIPPING WEIGHT: 7.1 lbs.
EMERGENCY SIGN: 7-7/8” x 7-7/8” Plastic Wall Sign.
OPTIONS
◊ AL1
(Air Horn Alarm)
◊ AL2
(Electrical Alarm)
◊ AL3
(Electrical Alarm)
◊ AL2-C1D2
(Electrical Alarm / Haz.
Area)
◊ AL3-C1D2
(Electrical Alarm / Haz.
Area)
◊ FLW
(Flow Switch)
◊ VPL
◊ PT
◊ ILS
◊ FPV
(Vapor Proof Light)
(P-Trap)
◊ SGN4
(In-Line Strainer)
(Eye Wash Floor Sign)
(Anti-Freeze Protection Valve)
◊ SSBV2
◊
◊
◊
◊
◊ SPV
(Anti-Scald Protection Valve)
◊
(1/2” Stainless Steel Valve)
INSTALLATION
Use cutting/drilling instruction template (supplied) to cut and drill holes in desired location on countertop. Once bowl is mounted securely to countertop using mounting hardware supplied, complete assembly of ball valve and push handle. Review drawing (as shown on other side) to assure proper installation. Be sure to apply a bead of waterproof caulk along edge of bowl and countertop to prevent water draining under countertop. Connect a water supply to the unit (use pipe sealant on all joints) that is a 1/2” minimum uninterrupted source of potable water.
Failure to use potable water can result in emergency units producing impure or contaminated water causing possible further injury. The drain tailpiece or waste should be connected to an adequate drain in compliance with local plumbing codes. This unit is supplied with a volume control that can control the amount of water delivered, even at higher pressures. This should be set after unit is completely installed so that streams from spray outlets converge in the middle of the eyewash bowl..
OPERATION
The eyewash is activated by pushing the trigger bar back 90°. Once the unit is activated, water will discharge from the spray outlets until the trigger bar is manually pulled back to the off position.
TESTING PROGRAM
The American National Standards Institute (ANSI) states that all safety emergency equipment shall be activated on a weekly basis to flush the line and verify proper operation. Speakman Company furnishes a testing record tag
(91-0635) with each unit. On this tag the date of inspection and the inspectors initials should be noted.
MAINTENANCE
The valve and the eyewash are the only portions of the unit that may require maintenance. Should you need parts to repair this unit, please reference the parts listing below for correct part numbers.
Reference additional technical sheet (supplied) for information on the
SE-505 eyewash. Before any maintenance is done be sure to shut the water
supply off.
WARNING: Use only genuine Speakman parts when repairing or
replacing components.
To order parts call 1-800-
537-2107.
SE-565
REPLACEMENT/REPAI
R PARTS
ITEM PART/GROUP # DESCRIPTION
1 SE-505 Eyewash
2
3
73-0079-MO
48-0348 10-24 x 5/16 Fill Head SS Screw
4
5
6
7
01-0628-MO
32-0171
45-0173
74-0009-MO
1/4-20 Wing Nut
1/4” #20 2-1/2” Lg. Brass Thread Screw
Brace
FLOW DATA
EYEWASH:
FLOW PRESSURE PSI (BAR) 30 (2.07)
FLOW RATE GPM (LPM) 3 (11)
NOTE: This unit should be connected to an uninterrupted source of potable water, with a minimum flowing pressure of 20 PSI and a maximum static pressure of 125 PSI.
SPEAKMAN COMPANY
The Quality leader Since 1869
P.O. Box 191, Wilmington, DE 19899-0191 USA
1-800-537-2107, Fax: 1-800-977-2747
Note: All units meet existing
ANSI Z358.1 1998
Standards and OSHA Rules.
Product improvements may cause specification and dimensional changes without notice.
04/02
92-1448 Rev-5