Sony XR-CA CA430X, CA440, CA400 cassette car stereo Service manual
Below you will find brief information for cassette car stereo XR-CA CA430X, cassette car stereo XR-CA CA440, cassette car stereo XR-CA CA400. This Sony cassette car stereo allows you to enjoy music from both cassette tapes and radio. It features 45W x 4 of power output and tone controls, including bass and treble, to customize your listening experience.
Advertisement
Advertisement
XR-CA430X/CA440
SERVICE MANUAL
AEP Model
UK Model
Photo: XR-CA430X
Model Name Using Similar Mechanism XR-CA400
Tape Transport Mechanism Type MG-25L-136
Cassette Player section
Tape track
Wow and flutter
Frequency response
Signal-to-noise ratio
4-track 2-channel stereo
0.08 % (WRMS)
30 – 18,000 Hz
Cassette type
TYPE II, IV
TYPE I
61 dB
58 dB
Tuner section
FM
Tuning range
Aerial terminal
87.5 – 108.0 MHz
External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity 8 dBf
Selectivity
Signal-to-noise ratio
75 dB at 400 kHz
66 dB (stereo),
72 dB (mono)
Harmonic distortion at 1 kHz
Separation
Frequency response
0.6 % (stereo),
0.3 % (mono)
35 dB at 1 kHz
30 – 15,000 Hz
MW/LW
Tuning range MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Aerial terminal External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity MW: 30
µ
V
LW: 40
µ
V
Power amplifier section
Outputs Speaker outputs
(sure seal connectors)
Speaker impedance 4 – 8 ohms
Maximum power output 45 W
×
4 (at 4 ohms)
SPECIFICATIONS
General
Outputs
Inputs
Tone controls
Power requirements
Dimensions
Mounting dimensions
Mass
Supplied accessories
Power aerial relay control terminal
Power amplifier control terminal
Telephone ATT control terminal
BUS control input terminal
BUS audio input terminal
Remote controller input terminal (XR-CA440 only)
Bass
±
9 dB at 100 Hz
Treble
±
9 dB at 10 kHz
12 V DC car battery
(negative earth)
Approx. 178
×
50
×
179 mm
(w/h/d)
Approx. 182
×
53
×
162 mm
(w/h/d)
Approx. 1.2 kg
Parts for installation and connections
Front panel case (1)
Note
This unit cannot be connected to a digital preamplifier or an equalizer.
Design and specifications are subject to change without notice.
FM/MW/LW CASSETTE CAR STEREO
9-873-467-02
2003A0500-1
C
2003.01
Sony Corporation
e Vehicle Company
Published by Sony Engineering Corporation
XR-CA430X/CA440
TABLE OF CONTENTS
1.
GENERAL
...................................................................
3
2.
DISASSEMBLY
2-1. Disassembly Flow ...........................................................
7
2-2. Mechanism Deck (MG-25L-136) ...................................
7
2-3. MAIN Board ...................................................................
8
2-4. Heat Sink (ISO) ...............................................................
8
3.
ASSEMBLY
3-1. Assembly Flow ................................................................
9
3-2. Housing ........................................................................... 10
3-3. Arm (Suction) ................................................................. 10
3-4. Lever (LDG-A)/(LDG-B) ............................................... 11
3-5. Gear (LDG-FT) ............................................................... 11
3-6. Guide (C) ......................................................................... 12
3-7. Mounting Position of Capstan/Reel Motor (M901) ....... 12
4.
MECHANICAL ADJUSTMENTS
....................... 13
5.
ELECTRICAL ADJUSTMENTS
Tape Deck Section .......................................................... 13
Tuner Section .................................................................. 13
6.
DIAGRAMS
6-1. Note for Printed Wiring Boards and
Schematic Diagrams ....................................................... 14
6-2. Printed Wiring Board – MAIN Board – ......................... 18
6-3. Schematic Diagram – MAIN Board (1/3) – ................... 19
6-4. Schematic Diagram – MAIN Board (2/3) – ................... 20
6-5. Schematic Diagram – MAIN Board (3/3) – ................... 21
6-6. Printed Wiring Board – KEY Board – ............................ 22
6-7. Schematic Diagram – KEY Board – .............................. 23
6-8. IC Pin Function Description ........................................... 24
7.
EXPLODED VIEWS
7-1. Chassis Section ............................................................... 26
7-2. Front Panel Section ......................................................... 27
7-3. MAIN Board Section ...................................................... 28
7-4. Mechanism Deck Section (MG-25L-136) ...................... 29
8.
ELECTRICAL PARTS LIST
............................... 30
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C during repairing.
• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or unsoldering.
2
SECTION 1
GENERAL
Location of controls
Refer to the pages listed for details.
ATT
SOURCE
MODE
RELEASE
SEL
VOL
AF
BTM
SENS
–
1
DISC
2
+
REP
3 4 5
+/ATA MTL
6 PTY TA
SEEK
AMS
D-BASS
MBP
DSPL OFF
a SOURCE (Power on/Tape/Radio/CD/
MD) select button
b MODE ( o) button
Selecting the source.
c VOL +/– button d ATT (attenuate) button e Display window f
Z (eject) button 8 g SEEK/AMS button
Tape:
Fast-forwarding, reversing a tape.
Radio:
Tuning in stations automatically.
Finding a station manually.
CD (MP3 files)/MD:
Skipping tracks.
h MBP (My Best sound Position) button
17 i D-BASS button 18 j RELEASE (front panel release) button k SEL (select) button
Selecting items.
l RESET button (located on the front side of the unit, behind the front panel) 6 m AF button 11, 13 n SENS/BTM button
Storing the stations with the strongest signals.
o Number buttons
Tape:
(3): REP (Repeat)
(5): BL SKIP (Blank Skip)
(6): ATA (Automatic Tuner Activation)
Radio:
Storing the desired station on each number button.
CD (MP3 files)/MD:
(1): DISC –
(2): DISC +
(3): REP (Repeat)
(4): SHUF (Shuffle)
MP3 files:
(5): ALBM –
(6): ALBM + p PTY/MTL (programme type/Metal)
button 9, 14 q TA button 12, 13 r DSPL (display mode change) button s OFF (Stop/Power off) button*
*
Warning when installing in a car without an ACC (accessory) position on the ignition switch
After turning off the ignition, be sure to press
(OFF) on the unit for 2 seconds to turn off the clock display.
Otherwise, the clock display does not turn off and this causes battery drain.
XR-CA430X/CA440
This section is extracted from instruction manual.
3
XR-CA430X/CA440
2
A
AUDIO OUT REAR
B
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
Source selector*
Signalquellenwähler*
Sélecteur de source*
Selettore di fonte*
Geluidsbronkiezer*
BUS CONTROL IN
*
not supplied nicht mitgeliefert non fourni non in dotazione niet meegeleverd
3
*
1
Insert with the cord upwards.
Mit dem Kabel nach oben einsetzen!
Insérez avec le câble vers le haut.
Inserire con il cavo rivolto verso l’alto.
Inbrengen met het snoer naar boven.
from car aerial*
2
von Autoantenne*
2
a partir de l’antenne de la voiture*
2
dall’antenna dell’auto*
2
van een auto-antenne*
2
7
BUS AUDIO
IN
AUDIO OUT REAR
BUS AUDIO
IN
AUDIO OUT
REAR
L
R
Supplied with XA-C30
Mit dem XA-C30 geliefert
Fourni avec le XA-C30
In dotazione con il modello XA-C30
Geleverd met de XA-C30
Source selector
(not supplied)
Signalquellenwähler
(nicht mitgeliefert)
Sélecteur de source (non fourni)
Selettore di fonte
(non in dotazione)
Geluidsbronkiezer
(niet meegeleverd)
XA-C30
Supplied with the CD/MD changer
Mit dem CD/MD-Wechsler geliefert
Fourni avec le changeur de CD/MD
In dotazione con il cambia CD/MD
Geleverd met de CD/MD-wisselaar
REMOTE IN
Fuse (10 A)
Sicherung (10 A)
Fusible (10 A)
Fusibile (10 A)
Zekering (10 A)
BUS CONTROL IN
8
Max. supply current 0.3 A max. Versorgungsstrom 0,3 A
Courant max. fourni 0,3 A
Alimentazione massima fornita 0,3 A
Max. voedingsstroom 0,3 A
RCA pin cord (not supplied)
Cinchkabel (nicht mitgeliefert)
Cordon à broche RCA (non fourni)
Cavo a piedini RCA (non in dotazione)
Tulpstekkersnoer (niet meegeleverd)
Blue/white striped
Blauweiß gestreift
Rayé bleu/blanc
A strisce blu e bianche
Blauw/wit gestreept
A
AMP REM
Light blue
Hellblau
Bleu ciel
Azzurro
Hemelsblauw
B
ATT
9
5 7 from the car’s power connector vom Lautsprecheranschluss des Fahrzeugs a partir du connecteur d’alimentation de la voiture dal connettore di alimentazione dell’auto van de autovoedingsstekker
4
4
5 continuous power supply permanente Stromversorgung alimentation continue alimentazione continua continu voeding power aerial control
Motorantennen-Steuerleitung antenne électrique comando dell’antenna elettrica automatische antenne
7
8 switched power supply geschaltete Stromversorgung alimentation commutée alimentazione commutata geschakelde voeding
Positions 1, 2, 3 and 6 do not have pins.
An Position 1, 2, 3 and 6 befinden sich keine Stifte.
Les positions 1, 2, 3 et 6 ne comportent pas de broches.
Le posizioni 1, 2, 3 e 6 non hanno piedini.
De posities 1, 2, 3 en 6 hebben geen pins.
earth
Masse masse terra aarding
8
*
1 XR-CA440 only nur XR-CA440 modèles XR-CA440 uniquement solo XR-CA440 alleen XR-CA440
*
2
Note for the aerial connecting
If your car aerial is an ISO (International
Organisation for Standardisation) type, use the
supplied adaptor 7 to connect it.
First connect the car aerial to the supplied adaptor, then connect it to the aerial jack of the master unit.
*
2
Hinweis zum Anschließen der Antenne
Wenn Ihre Fahrzeugantenne der ISO-Norm (ISO =
International Organization for Standardization -
Internationale Normungsgemeinschaft) entspricht, schließen Sie sie mithilfe des
mitgelieferten Adapters 7 an.
Verbinden Sie zuerst die Fahrzeugantenne mit dem mitgelieferten Adapter und verbinden Sie diesen dann mit der Antennenbuchse des
Hauptgeräts.
*
2
Remarque sur le raccordement de l’antenne
Si votre antenne de voiture est de type ISO
(organisation internationale de normalisation),
utilisez l’adaptateur fourni 7 pour la raccorder.
Raccordez d’abord l’antenne de voiture à l’adaptateur fourni et, ensuite, à la prise d’antenne de l’appareil principal.
*
2
Nota per il collegamento dell’antenna
Se l’antenna della macchina è di tipo ISO
(International Organization Standardization),
utilizzare l’adattatore 7 in dotazione per
collegarla.
Collegare prima l’antenna della macchina all’adattatore in dotazione, quindi collegarla alla presa dell’antenna dell’apparecchio principale.
*
2
Opmerking bij de antenne-aansluiting
Indien uw wagen is uitgerust met een antenne van het type ISO (International Organisation for
Standardization), moet u die aansluiten met
behulp van de meegeleverde adaptor 7.
Sluit eerst de auto-antenne aan op de meegeleverde adaptor en vervolgens de antennestekker op het hoofdtoestel.
1 3 5 7 from the car’s speaker connector vom Lautsprecheranschluss des Fahrzeugs a partir du connecteur de haut-parleur de la voiture dal connettore del diffusore dell’auto van de autoluidsprekerstekker
2 4 6 8
1
2
+
–
Speaker, Rear, Right
Lautsprecher hinten rechts haut-parleur, arrière, droit
Diffusore, posteriore, destro
Luidspreker, achter, rechts
Speaker, Rear, Right
Lautsprecher hinten rechts haut-parleur, arrière, droit
Diffusore, posteriore, destro
Luidspreker, achter, rechts
5
6
+
–
Speaker, Front, Left
Lautsprecher vorne links haut-parleur, avant, gauche
Diffusore, anteriore, sinistro
Luidspreker, voor, links
Speaker, Front, Left
Lautsprecher vorne links haut-parleur, avant, gauche
Diffusore, anteriore, sinistro
Luidspreker, voor, links
3
4
+
–
Speaker, Front, Right
Lautsprecher vorne rechts haut-parleur, avant, droit
Diffusore, anteriore, destro
Luidspreker, voor, rechts
Speaker, Front, Right
Lautsprecher vorne rechts haut-parleur, avant, droit
Diffusore, anteriore, destro
Luidspreker, voor, rechts
7
8
+
–
Speaker, Rear, Left
Lautsprecher hinten links haut-parleur, arrière, gauche
Diffusore, posteriore, sinistro
Luidspreker, achter, links
Speaker, Rear, Left
Lautsprecher hinten links haut-parleur, arrière, gauche
Diffusore, posteriore, sinistro
Luidspreker, achter, links
Negative polarity positions 2, 4, 6, and 8 have striped cords.
An den negativ gepolten Positionen (2, 4, 6 und 8) befinden sich gestreifte Adern.
Les positions de polarité négative 2, 4, 6 et 8 sont dotées de cordons rayés.
Le posizioni a polarità negativa 2, 4, 6 e 8 hanno cavi rigati.
De negatieve posities 2, 4, 6 en 8 hebben gestreepte kabels.
4
XR-CA430X/CA440
Cautions
• This unit is designed for negative earth 12 V DC operation only.
• Do not get the wires under a screw, or caught in moving parts
(e.g. seat railing).
• Before making connections, turn the car ignition off to avoid short circuits.
• Connect the power connecting cord 9 to the unit and speakers before connecting it to the auxiliary power connector.
• Run all earth wires to a common earth point.
• Be sure to insulate any loose unconnected wires with electrical tape for safety.
Notes on the power supply cord (yellow)
• When connecting this unit in combination with other stereo components, the connected car circuit’s rating must be higher than the sum of each component’s fuse.
• When no car circuits are rated high enough, connect the unit directly to the battery.
Power connection
Power connectors may vary depending on the car. Check your car’s power connector diagram to make sure the connections match correctly. There are two basic types. You may need to switch the positions of the jump connector. Before connecting the unit to the car’s power supply, be sure to match the position of the jump connector to the car’s pin order. If the power connector of your car does not match the connector on the unit, use the connector 9. If you have any questions or problems connecting your unit that are not covered in this manual, please consult the car dealer.
WARNING
Shifting the fuse
Check the pin position of the power connector of the car with the table in connection diagram (
3). If positions 4 and 7 are reversed, remove the fuse and shift it to the lower position as shown in the illustration.
Vorsicht
• Dieses Gerät ist ausschließlich für den Betrieb bei 12 V Gleichstrom
(negative Erdung) bestimmt.
• Achten Sie darauf, dass die Kabel nicht unter einer Schraube oder zwischen beweglichen Teilen wie z. B. in einer Sitzschiene eingeklemmt werden.
• Schalten Sie, bevor Sie irgendwelche Anschlüsse vornehmen, die
Zündung des Fahrzeugs aus, um Kurzschlüsse zu vermeiden.
• Verbinden Sie das Stromversorgungskabel 9 mit dem Gerät und den
Lautsprechern, bevor Sie es mit dem Hilfsstromanschluss verbinden.
• Schließen Sie alle Erdungskabel an einen gemeinsamen
Massepunkt an.
• Aus Sicherheitsgründen müssen alle losen, nicht angeschlossenen
Drähte mit Isolierband isoliert werden.
Hinweise zum Stromversorgungskabel (gelb)
• Wenn Sie dieses Gerät zusammen mit anderen Stereokomponenten anschließen, muss der Autostromkreis, an den die Geräte angeschlossen sind, eine höhere Leistung aufweisen als die Summe der Sicherungen der einzelnen Komponenten.
• Wenn kein Autostromkreis eine so hohe Leistung aufweist, schließen
Sie das Gerät direkt an die Batterie an.
Stromanschluss
Die Stromanschlüsse verschiedener Fahrzeuge können sich voneinander unterscheiden. Überprüfen Sie anhand des
Stromanschluss-Schaltplans des Fahrzeugs, ob die Anschlüsse
übereinstimmen. Es gibt zwei Grundtypen. Sie müssen möglicherweise die Position des Überbrückungsanschlusses umschalten. Bevor Sie das Gerät an die Stromversorgung des
Fahrzeugs anschließen, stellen Sie sicher, dass die Position des
Überbrückungsanschlusses mit der Stiftbelegung des Fahrzeugs
übereinstimmt. Wenn der Stromanschluss des Fahrzeugs nicht mit dem Anschluss am Gerät übereinstimmt, verwenden Sie
Anschluss 9. Sollten beim Anschließen des Geräts Fragen oder
Probleme auftreten, auf die in dieser Anleitung nicht eingegangen wird, wenden Sie sich bitte an Ihren Autohändler.
ACHTUNG
Versetzen der Sicherung
Vergleichen Sie die Stiftposition des Stromanschlusses im
Fahrzeug mit der Tabelle im Anschlussdiagramm (
3). Sind die
Stiftpositionen 4 und 7 umgekehrt, entfernen Sie die Sicherung und bringen sie, wie in der Abbildung gezeigt, stattdessen unten an.
Précautions
• Cet appareil est conçu pour fonctionner sur courant continu de 12 V avec masse négative.
• Evitez de fixer des vis sur les câbles ou de coincer ceux-ci dans des pièces mobiles (par exemple, armature de siège).
• Avant d’effectuer des raccordements, éteignez le moteur pour éviter les courts-circuits.
• Brancher le cordon d’alimention 9 sur l’appareil et les haut-parleurs avant de le brancher sur le connecteur d’alimentation auxiliaire.
• Rassembler tous les fils de terre en un point de masse commun.
• Veillez à isoler tout fil avec du chatterton tout fil lâche non raccordé.
Notes sur le cordon d’alimentation (jaune)
• Lorsque cet appareil est raccordé à d’autres éléments stéréo, la valeur nominale des circuits de la voiture raccordée doit être supérieure à la somme des fusibles de chaque élément.
• Si aucun circuit de la voiture n’est assez puissant, raccordez directement l’appareil à la batterie.
Raccordement de l’alimentation
Les connecteurs d’alimentation peuvent varier suivant le modèle de la voiture. Vérifiez le diagramme du connecteur d’alimentation de votre voiture pour vérifier si les connexions correspondent. On distingue deux types de base. Il se peut que vous deviez commuter les positions du cavalier. Avant de raccorder l’appareil à l’alimentation de la voiture, faites correspondre la position du cavalier à l’ordre des broches de la voiture. Si le connecteur d’alimentation de votre véhicule ne correspond pas au connecteur de l’appareil, utilisez le connecteur 9. Si vous avez des questions ou des problèmes au sujet du raccordement de votre appareil qui ne sont pas abordés dans le présent mode d’emploi, consultez votre concessionnaire automobile.
AVERTISSEMENT
Décalage du fusible
Vérifiez la position de la broche du connecteur d’alimentation de la voiture dans le tableau des schémas de raccordement (
3). Si les positions 4 et 7 sont inversées, retirez le fusible et décalez-le sur la position inférieure comme indiqué dans l’illustration.
Attenzione
• Questo apparecchio è stato progettato per l’uso solo a 12 V CC con massa negativa.
• Evitare che i cavi rimangano bloccati da una vite o incastrati nelle parti mobili (ad esempio nelle guide scorrevoli dei sedili).
• Prima di effettuare i collegamenti, spegnere il motore dell’automobile onde evitare di causare cortocircuiti.
• Collegare il cavo di collegamento dell’alimentazione 9 all’apparecchio e ai diffusori prima di collegarlo al connettore di alimentazione ausiliare.
• Portare tutti i cavi di massa a un punto di massa comune.
•Per sicurezza, assicurarsi di isolare qualsiasi cavo non collegato mediante apposito nastro.
Note sul cavo di alimentazione (giallo)
• Se questo apparecchio viene collegato in combinazione con altri componenti stereo, la potenza nominale dei circuiti dell’automobile deve essere superiore a quella prodotta dalla somma dei fusibili di ciascun componente.
• Se la potenza nominale dei circuiti dell’automobile non è sufficiente, collegare l’apparecchio direttamente alla batteria.
Collegamento con l’alimentazione
I connettori di alimentazione possono essere diversi a seconda del tipo di automobile. Controllare il diagramma relativo al connettore di alimentazione della propria auto per assicurarsi che i collegamenti corrispondano perfettamente. Esistono due principali tipi di connettore di alimentazione. Potrebbe essere necessario cambiare le posizioni del connettore ponticello. Prima di collegare l’apparecchio all’alimentazione dell’auto, assicurarsi di far corrispondere la posizione del connettore ponticello all’ordine dei piedini dell’auto. Se il connettore di alimentazione dell’auto non è compatibile con quello dell’apparecchio, utilizzare il connettore
9. In caso di domande o problemi relativi al collegamento dell’apparecchio non contemplati in questo manuale, contattare il rivenditore dell’automobile.
AVVERTENZA
Come spostare il fusibile
Verificare la posizione del piedino del connettore di alimentazione dell’auto utilizzando la tabella nello schema di collegamento (
3).
Se i piedini 4 e 7 sono invertiti, rimuovere il fusibile e spostarlo nella posizione più in basso come mostrato nella figura.
Let op!
• Dit apparaat is ontworpen voor gebruik op gelijkstroom van een
12 Volts auto-accu, negatief geaard.
• Zorg ervoor dat de draden niet onder een schroef of tussen bewegende onderdelen (b.v. zetelrail) terechtkomen.
• Alvorens aansluitingen te verrichten moet u het contact afzetten om kortsluiting te vermijden.
• Sluit het netsnoer 9 aan op het toestel en de luidsprekers vooraleer u het op de hulpvoedingsaansluiting aansluit.
• Sluit alle aarddraden op een gemeenschappelijk aardpunt aan.
•Voorzie niet aangesloten draden om veiligheidsredenen altijd van isolatietape.
Opmerkingen bij de voedingskabel (geel)
• Wanneer u dit toestel aansluit samen met andere componenten, moet het vermogen van de aangesloten autostroomkring groter zijn dan de som van de zekeringen van elke component afzonderlijk.
• Wanneer het vermogen ontoereikend is, moet u het toestel rechtstreeks aansluiten op de batterij.
Voedingsaansluiting
Voedingsstekkers kunnen verschillen van auto tot auto. Controleer het voedingsschema van uw auto om na te gaan of de aansluitingen kloppen. Er zijn twee basistypes. Eventueel moeten de posities van de jumpstekker worden omgewisseld. Alvorens het toestel aan te sluiten op de voeding van de auto, moet u controleren of de jumpstekkerpositie overeenkomt met de pinvolgorde. Gebruik stekker 9 indien de voedingsstekker van uw auto niet past op de stekker van het toestel. Voor alle vragen en problemen in verband met het toestel kunt u terecht bij uw autodealer.
WAARSCHUWING
Verplaatsen van de zekering
Controleer de penpositie van de voedingsstekker in de auto aan de hand van het aansluitschema (
3). Als de posities 4 en 7 omgekeerd zijn, moet u de zekering verwijderen en deze in de onderste positie aanbrengen zoals aangegeven in de afbeelding.
Parts list (
1)
The numbers in the list are keyed to those in the instructions.
Caution
Handle the bracket 1 carefully to avoid injuring your fingers.
Teileliste (
1)
Die Nummern in der Liste sind dieselben wie im Erläuterungstext.
Vorsicht
Seien Sie beim Umgang mit der Halterung 1 vorsichtig, damit Sie sich nicht die Hände verletzen.
Liste des composants (
1)
Les numéros de l’illustration correspondent à ceux des instructions.
Avertissement
Manipulez avec précautions le support 1 pour éviter de vous blesser aux doigts.
Elenco dei componenti (
1)
I numeri nella lista corrispondono a quelli riportati nelle istruzioni.
Attenzione
Maneggiare la staffa 1 con cautela per evitare di ferirsi le mani.
Onderdelenlijst (
1)
De nummers in de afbeelding verwijzen naar die in de montageaanwijzingen.
Opgelet
Houd de beugel 1 voorzichtig vast zodat u uw vingers niet verwondt.
1
Connection example (
2)
Notes (
2-A )
• Be sure to connect the earth cord before connecting the amplifier.
• If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated.
Tip (
2-B- )
For connecting two or more CD/MD changers, the source selector
XA-C30 (optional) is necessary.
Connection diagram (
3)
A
To AMP REMOTE IN of an optional power amplifier
This connection is only for amplifiers. Connecting any other system may damage the unit.
B
To the interface cable of a car telephone
Warning
If you have a power aerial without a relay box, connecting this unit with the power connecting cord 9 may damage the aerial.
Notes on the control leads
• The power aerial control lead (blue) supplies +12 V DC when you turn on the tuner or when you activate the AF (Alternative
Frequency), TA (Traffic Announcement) function.
• When your car has built-in FM/MW/LW aerial in the rear/side glass, connect the power aerial control lead (blue) or the accessory power input lead (red) to the power terminal of the existing aerial booster. For details, consult your dealer.
• A power aerial without a relay box cannot be used with this unit.
Memory hold connection
When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker.
• Do not connect the earth lead of this unit to the negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit.
• To avoid a malfunction, do not use the built-in speaker wires installed in your car if the unit shares a common negative (–) lead for the right and left speakers.
• Do not connect the unit’s speaker cords to each other.
1
Anschlussbeispiel (
2)
Hinweise (
2-A)
• Schließen Sie unbedingt zuerst das Massekabel an, bevor Sie den
Verstärker anschließen.
• Wenn Sie einen gesondert erhältlichen Endverstärker anschließen und den integrierten Verstärker nicht benutzen, wird der
Signalton deaktiviert.
Tipp (
2-B- )
Zum Anschließen von zwei oder mehr CD/MD-Wechslern wird der gesondert erhältliche Signalquellenwähler XA-C30 benötigt.
Anschlussdiagramm (
3)
A
An AMP REMOTE IN des gesondert erhältlichen Endverstärkers
Dieser Anschluss ist ausschließlich für Verstärker gedacht.
Schließen Sie nichts anderes daran an. Andernfalls kann das
Gerät beschädigt werden.
B
An Schnittstellenkabel eines Autotelefons
Warnung
Wenn Sie eine Motorantenne ohne Relaiskästchen verwenden, kann durch Anschließen dieses Geräts mit dem Stromversorgungskabel 9 die Antenne beschädigt werden.
Hinweise zu den Steuerleitungen
• Die Motorantennen-Steuerleitung (blau) liefert + 12 V Gleichstrom, wenn Sie den Tuner einschalten oder die AF- (Alternativfrequenzen) oder die TA-Funktion (Verkehrsdurchsagen) aktivieren.
• Wenn das Fahrzeug mit einer in der Heck-/Seitenfensterscheibe integrierten FM (UKW)/MW/LW-Antenne ausgestattet ist, schließen Sie die Motorantennen-Steuerleitung (blau) oder die
Zubehörstromversorgungsleitung (rot) an den
Stromversorgungsanschluss des vorhandenen
Antennenverstärkers an. Näheres dazu erfahren Sie bei Ihrem
Händler.
• Es kann nur eine Motorantenne mit Relaiskästchen angeschlossen werden.
Stromversorgung des Speichers
Wenn die gelbe Stromversorgungsleitung angeschlossen ist, wird der
Speicher stets (auch bei ausgeschalteter Zündung) mit Strom versorgt.
Hinweise zum Lautsprecheranschluss
• Schalten Sie das Gerät aus, bevor Sie die Lautsprecher anschließen.
• Verwenden Sie Lautsprecher mit einer Impedanz zwischen 4 und 8
Ohm und ausreichender Belastbarkeit. Ansonsten können die
Lautsprecher beschädigt werden.
• Verbinden Sie die Lautsprecheranschlüsse nicht mit dem Wagenchassis und verbinden Sie auch nicht die Anschlüsse des rechten mit denen des linken Lautsprechers.
• Verbinden Sie die Masseleitung dieses Geräts nicht mit dem negativen
(–) Lautsprecheranschluss.
• Versuchen Sie nicht, Lautsprecher parallel anzuschließen.
• An die Lautsprecheranschlüsse dieses Geräts dürfen nur
Passivlautsprecher angeschlossen werden. Schließen Sie keine
Aktivlautsprecher (Lautsprecher mit eingebauten Verstärkern) an, da das Gerät sonst beschädigt werden kann.
• Um Fehlfunktionen zu vermeiden, verwenden Sie nicht die im
Fahrzeug installierten, integrierten Lautsprecherleitungen, wenn am
Ende eine gemeinsame negative (–) Leitung für den rechten und den linken Lautsprecher verwendet wird.
• Verbinden Sie nicht die Lautsprecherkabel des Geräts miteinander.
1
Exemple de raccordement (
2)
Remarques (
2-A)
• Raccordez d’abord le fil de masse avant de connecter l’amplificateur.
• Si vous raccordez un amplificateur de puissance en option et si vous n’utilisez pas l’amplificateur intégré, le bip sera désactivé.
Conseil (
2-B- )
Dans le cas du raccordement de deux changeurs de CD/MD ou plus, le sélecteur de source XA-C30 (en option) est indispensable.
Schémas de raccordement (
3)
A
Au niveau du AMP REMOTE IN d’un amplificateur de puissance en option
Cette connexion existe seulement pour les amplificateurs. Le raccordement à tout autre système peut endommager l’appareil.
B
Vers le câble d’interface d’un téléphone de voiture
Avertissement
Si vous disposez d’une antenne électrique sans boîtier de relais, le raccordement de cet appareil avec le cordon d’alimentation
9 peut endommager l’antenne.
Remarques sur les fils de commande
• Le fil de commande de l’antenne (bleu) fournit du courant continu de
+12 V lorsque vous allumez la radio ou lorsque vous activez la fonction
AF (fréquence alternative) ou la fonction TA (messages de radioguidage).
• Lorsque votre voiture est équipée d’une antenne FM/MW/LW intégrée dans la vitre arrière/latérale, raccordez la sortie de commande de l’antenne (bleu) ou l’entrée d’alimentation des accessoires (rouge) à la borne de l’amplificateur d’antenne existant. Pour plus de détails, consultez votre revendeur.
• Une antenne électrique sans boitier de relais ne peut pas être utilisée avec cet appareil.
Raccordement pour la sauvegarde de la mémoire
Lorsque le fil d’entrée d’alimentation jaune est connecté, le circuit de la mémoire est alimenté en permanence même si la clé de contact est sur la position d’arrêt.
Remarques sur le raccordement des haut-parleurs
• Avant de raccorder les haut-parleurs, mettez l’appareil hors tension.
• Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms avec une capacité de manipulation adéquate pour éviter de les endommager.
• Ne raccordez pas les bornes du système de haut-parleurs au châssis de la voiture et ne raccordez pas les bornes du haut-parleur droit à celles du haut-parleur gauche.
• Ne raccordez pas le câble de masse de cet appareil à la borne négative
(–) du haut-parleur.
• N’essayez pas de raccorder les haut-parleurs en parallèle.
• Raccordez uniquement des haut-parleurs passifs. Le raccordement de haut-parleurs actifs (avec amplificateurs intégrés) aux bornes des hautparleurs peut endommager l’appareil.
• Pour éviter tout dysfonctionnement, n’utilisez pas les fils des hautparleurs intégrés installés dans votre voiture si l’appareil partage un fil négatif commun (–) pour les haut-parleurs droit et gauche.
• Ne raccordez pas entre eux les cordons des haut-parleurs de l’appareil.
1
Esempi di collegamento (
2)
Note (
2-A)
• Assicurarsi di collegare il cavo di terra prima di collegare l’apparecchio all’amplificatore.
• Se si effettua il collegamento di un amplificatore di potenza opzionale e l’amplificatore incorporato non viene utilizzato, il segnale acustico si disattiva.
Suggerimento (
2-B- )
Per collegare due o più cambia CD/MD, è necessario utilizzare il selettore di fonte XA-C30 (opzionali).
Schema di collegamento (
3)
A
A AMP REMOTE IN di un amplificatore di potenza opzionale
Questo collegamento è riservato esclusivamente agli amplificatori. Non collegare un tipo di sistema diverso onde evitare di causare danni all’apparecchio.
B
Al cavo interfaccia di un telefono per auto
Avvertenza
Quando si collega l’apparecchio con il cavo di alimentazione
9, si potrebbe danneggiare l’antenna elettrica se questa non dispone di scatola a relè.
Note sui cavi di controllo
• Il cavo (blu) di controllo dell’antenna elettrica fornisce alimentazione pari a +12 V CC quando si attiva il sintonizzatore o la funzione TA
(notiziario sul traffico) AF (frequenza alternativa).
• Se l’automobile è dotata di antenna FM/MW/LW incorporata nel vetro posteriore/laterale, collegare il cavo (blu) di controllo dell’antenna elettrica o il cavo (rosso) di ingresso dell’alimentazione opzionale al terminale di alimentazione del preamplificatore dell’antenna esistente. Per ulteriori informazioni, consultare il proprio fornitore.
• Non è possibile utilizzare un’antenna elettrica senza scatola a relè con questo apparecchio.
Collegamento per la conservazione della memoria
Quando il cavo di ingresso alimentazione giallo è collegato, viene sempre fornita alimentazione al circuito di memoria anche quando l’interruttore di accensione è disattivato
Note sul collegamento dei diffusori
• Prima di collegare i diffusori spegnere l’apparecchio.
• Usare diffusori di impedenza compresa tra 4 e 8 ohm e con capacità di potenza adeguata, altrimenti i diffusori potrebbero venir danneggiati.
• Non collegare i terminali del sistema diffusori al telaio dell’auto e non collegare i terminali del diffusore destro a quelli del diffusore sinistro.
• Non collegare il cavo di terra di questo apparecchio al terminale negativo (–) del diffusore.
• Non collegare i diffusori in parallelo.
• Non collegare alcun diffusore attivo (con amplificatore incorporato) ai terminali dei diffusori dell’apparecchio perché si potrebbero danneggiare i diffusori attivi. Assicurarsi di collegare diffusori passivi a questi terminali.
• Per evitare problemi di funzionamento, non utilizzare i cavi dei diffusori incorporati installati nell’automobile se il terminale dell’apparecchio condivide un cavo comune negativo (–) per i diffusori destro e sinistro.
• Non collegare fra loro i cavi dei diffusori dell’apparecchio.
1
Voorbeeldaansluitingen (
2)
Opmerkingen (
2-A)
• Sluit eerst de massakabel aan alvorens de versterker aan te sluiten.
• Wanneer u een los verkrijgbare vermogensversterker aansluit en de ingebouwde versterker niet gebruikt, wordt de pieptoon uitgeschakeld.
Tip (
2-B- )
Om twee of meer CD/MD-wisselaars aan te sluiten, hebt u de geluidsbronkiezer XA-C30 (optioneel) nodig.
Aansluitschema (
3)
A
Naar AMP REMOTE IN van een los verkrijgbare vermogensversterker
Deze aansluiting is alleen bedoeld voor versterkers. Door een ander systeem aan te sluiten kan het toestel worden beschadigd.
B
Naar het interface-snoer van een autotelefoon
Opgelet
Indien u beschikt over een elektrische antenne zonder relaiskast, kan de antenne worden beschadigd wanneer u dit toestel aansluit met behulp van de voedingskabel 9.
Opmerking betreffende de aansluitsnoeren
• De antennevoedingskabel (blauw) levert +12 V gelijkstroom wanneer u de tuner aanschakelt of de AF (Alternative Frequency), TA (Traffic
Announcement) functie activeert.
• Wanneer uw auto is uitgerust met een FM/MW (MG)/LW (LG)-antenne in de achterruit/voorruit, moet u de antennevoedingskabel (blauw) of de hulpvoedingskabel (rood) aansluiten op de voedingsingang van de bestaande antenneversterker. Raadpleeg uw dealer voor meer details.
• Met dit apparaat is het niet mogelijk een automatische antenne zonder relaishuis te gebruiken.
Instandhouden van het geheugen
Zolang de gele stroomdraad is aangesloten, blijft de stroomvoorziening van het geheugen intact, ook wanneer het contact van de auto wordt uitgeschakeld.
Opmerkingen betreffende het aansluiten van de luidsprekers
• Zorg dat het apparaat is uitgeschakeld, alvorens de luidsprekers aan te sluiten.
• Gebruik luidsprekers met een impedantie van 4 tot 8 Ohm en let op dat die het vermogen van de versterker kunnen verwerken. Als dit wordt verzuimd, kunnen de luidsprekers ernstig beschadigd raken.
• Verbind in geen geval de aansluitingen van de luidsprekers met het chassis van de auto en sluit de aansluitingen van de rechter en linker luidspreker niet op elkaar aan.
• Verbind de massakabel van dit toestel niet met de negatieve (–) aansluiting van de luidspreker.
• Probeer nooit de luidsprekers parallel aan te sluiten.
• Sluit geen actieve luidsprekers (met ingebouwde versterkers) aan op de luidspreker-aansluiting van dit apparaat. Dit zal leiden tot beschadiging van de actieve luidsprekers. Sluit dus altijd uitsluitend luidsprekers zonder ingebouwde versterker aan.
• Om defecten te vermijden mag u de bestaande luidsprekerbedrading in uw auto niet gebruiken wanneer er een gemeenschappelijke negatieve (–) draad is voor de rechter en linker luidsprekers.
• Verbind de luidsprekerdraden niet met elkaar.
5
XR-CA430X/CA440
4 A
(OFF)
(RELEASE)
5 1
1
2
182 mm
53 mm
Bend these claws outward for a tight fit, if necessary.
Falls erforderlich, diese Klammern für einen sicheren Halt hochbiegen.
Plier ces griffes vers l’extérieur pour assurer, si nécessaire, une implantation correcte.
Piegare questi morsetti verso l’esterno per un‘installazione più sicura, se necessario.
Indien nodig kunt u deze lipjes ombuigen voor een steviger bevestiging.
B
3
5
6
6
6 5
5
4
Dashboard
Armaturenbrett
Tableau de bord
Cruscotto
Dashboard
1
4
Fire wall
Motorraumtrennwand paroi ignifuge
Parete frangifiamma
Brandschot
2
3
Precautions
• Choose the installation location carefully so that the unit will not interfere with normal driving operations.
• Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperature, such as in direct sunlight or near heater ducts.
• Use only the supplied mounting hardware for a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 20°.
How to detach and attach the
front panel (
4)
Before installing the unit, detach the front panel.
4-A To detach
Before detaching the front panel, be sure to press
(OFF).
Press
(RELEASE), then slide the front panel a little to the left, and pull it off towards you.
4-B To attach
Attach part A of the front panel to part B of the unit as illustrated and push the left side into position until it clicks.
Mounting example (
Installation in the dashboard
5)
Vorsichtsmaßnahmen
• Wählen Sie den Einbauort sorgfältig so aus, dass das
Gerät beim Fahren nicht hinderlich ist.
• Bauen Sie das Gerät so ein, dass es keinen hohen
Temperaturen (keinem direkten Sonnenlicht, keiner
Warmluft von der Heizung), keinem Staub, keinem
Schmutz und keinen starken Vibrationen ausgesetzt ist.
• Für eine sichere Befestigung verwenden Sie stets nur die mitgelieferten Montageteile.
Hinweis zum Montagewinkel
Das Gerät sollte in einem Winkel von weniger als 20° montiert werden.
Abnehmen und Anbringen der
Frontplatte (
4)
Nehmen Sie die Frontplatte vor dem Einbau des
Geräts ab.
4-A Abnehmen
Schalten Sie das Gerät vor dem Abnehmen der
Frontplatte unbedingt mit
(OFF) aus. Drücken Sie
(RELEASE), schieben Sie anschließend die Frontplatte ein wenig nach links und ziehen Sie sie auf sich zu heraus.
4-B Anbringen
Setzen Sie Teil A der Frontplatte wie in der Abbildung dargestellt an Teil B des Geräts an und drücken Sie die linke Seite der Frontplatte an, bis sie mit einem Klicken einrastet.
Précautions
• Choisir soigneusement l’emplacement de l’installation afin que l’appareil ne gêne pas la conduite normale du véhicule.
• Eviter d’installer l’appareil dans un endroit exposé à des températures élevées, comme en plein soleil ou à proximité d’une bouche d’air chaud, ou à de la poussière, saleté ou à des vibrations violentes.
• Pour garantir un montage sûr, n’utiliser que le matériel fourni.
Réglage de l’angle de montage
Ajuster l’inclinaison à un angle inférieur à 20°.
Precauzioni
• Scegliere con attenzione la posizione per l’installazione in modo che l’apparecchio non interferisca con le operazioni di guida del conducente.
• Evitare di installare l’apparecchio dove sia soggetto ad alte temperature, come alla luce solare diretta o al getto di aria calda dell’impianto di riscaldamento, o dove possa essere soggetto a polvere, sporco e vibrazioni eccessive.
• Utilizzare solo il materiale di montaggio in dotazione per un’installazione stabile e sicura.
Regolazione dell’angolo di montaggio
Regolare l’angolo di montaggio in modo che sia inferiore a 20°.
Voorzorgsmaatregelen
• Kies de installatieplaats zorgvuldig zodat het toestel de bestuurder niet hindert tijdens het rijden.
• Installeer het apparaat niet op plaatsen waar het blootgesteld wordt aan hoge temperaturen, b.v. in direct zonlicht of bij de warme luchtstroom van de autoverwarming, aan sterke trillingen, of waar het in contact komt met veel stof of vuil.
• Gebruik voor het veilig en stevig monteren van het apparaat uitsluitend de bijgeleverde montageonderdelen.
Maximale montagehoek
Installeer het apparaat nooit onder een hoek van meer dan 20° met het horizontale vlak.
Retrait et pose de la façade (
4)
Avant d’installer l’appareil, déposer la façade.
4-A Pour la retirer
Avant de déposer la façade, ne pas oublier d’appuyer sur
(OFF). Appuyer ensuite sur (RELEASE), puis faire glisser la façade légèrement vers la gauche et enlever la façade en tirant à soi.
4-B Pour la fixer
Fixer la partie A de la façade sur la partie B de l’appareil, comme indiqué sur l’illustration, puis appuyer sur le côté gauche jusqu’au déclic.
Exemple de montage (
Installation dans le tableau de bord
5)
Come rimuovere e reinserire il pannello anteriore (
4)
Prima di installare l’apparecchio rimuovere il pannello anteriore.
4-A Per rimuoverlo
Prima di rimuovere il pannello anteriore, premere
(OFF). Premere (RELEASE), quindi far scorrere leggermente il pannello anteriore verso sinistra e tirarlo verso di sé.
4-B Per reinserirlo
Applicare la parte A del pannello anteriore alla parte B dell’apparecchio come mostrato nell’illustrazione e premere il lato sinistro fino a sentire uno scatto.
Verwijderen en bevestigen van het afneembare voorpaneel (
4)
Verwijder, alvorens met het installeren te beginnen, het afneembare voorpaneel.
4-A Verwijderen
Vergeet niet, voordat u het voorpaneel verwijdert, eerst op
(OFF) te drukken. Druk vervolgens op de
(RELEASE) toets, schuif het voorpaneel iets naar links en trek het naar u toe.
4-B Bevestigen
Breng deel A van het voorpaneel aan op deel B van het apparaat zoals afgebeeld en druk op de linkerzijde tot deze vastklikt.
Esempio di montaggio (
5)
Installazione nel cruscotto
Montagevoorbeeld (
5)
Montage in het dashboard
Warning when installing in a car without ACC (accessory) position on the ignition key switch
Be sure to press
(OFF) on the unit for two seconds
to turn off the clock display after turning off the engine.
When you press
(OFF) only momentarily, the clock display does not turn off and this causes battery wear.
RESET button
When the installation and connections are completed, be sure to press the RESET button with a ball-point pen, etc.
Montagebeispiel (
5)
Installation im Armaturenbrett
Warnhinweis zur Installation des
Geräts in einem Auto mit
Zündschloss ohne Zubehörposition
ACC oder I
Drücken Sie am Gerät unbedingt zwei Sekunden lang
(OFF), um die Uhrzeitanzeige auszurschalten,
nachdem Sie den Motor ausgeschaltet haben.
Wenn Sie
(OFF) nur kurz drücken, wird die
Uhrzeitanzeige nicht ausgeschaltet und der
Autobatterie wird Strom entzogen.
Avertissement en cas d’installation dans une voiture dont le contact ne comporte pas de position ACC (accessoires)
Appuyez sur la touche
(OFF) de l’appareil pendant
deux secondes pour désactiver l’affichage de l’horloge après avoir coupé le moteur.
Si vous n’appuyez que brièvement sur
(OFF), l’affichage de l’horloge ne disparaît pas, ce qui provoque la décharge de la batterie.
Touche RESET
Quand l’installation et les raccordements sont terminés, appuyer sur la touche RESET avec un stylo à bille, ou un autre objet pointu.
Taste RESET
Nach der Installation und dem Anschluss muss die
Taste RESET mit einem Kugelschreiber o. ä. gedrückt werden.
Informazioni importanti per quando si effettua l’installazione su un’auto sprovvista della posizione ACC sull’interruttore di accensione
Assicurarsi di premere
(OFF) sull’apparecchio per
due secondi per spegnere il display dell’orologio dopo che il motore è stato spento.
Se si preme
(OFF) solo per un attimo, il display dell’orologio non si spegne causando in questo modo lo scaricamento della batteria.
Tasto RESET
Dopo avere terminato l’installazione e i collegamenti, assicurarsi di premere il tasto RESET con la punta di una penna a sfera, o simile.
Opgelet bij het monteren in een auto waarvan het contactslot geen
ACC (accessory) stand heeft
Druk
(OFF) op het toestel gedurende twee seconden
in om de klokweergave uit te schakelen na het afzetten van de motor.
Indien u slechts even op
(OFF) drukt, verdwijnt de tijdindicatie niet waardoor de batterij uitgeput raakt.
RESET-toets
Druk, nadat u het apparaat heeft geïnstalleerd en de aansluitingen heeft gemaakt, met een balpen of een ander puntig voorwerp op de RESET-toets.
6
XR-CA430X/CA440
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1.
DISASSEMBLY FLOW
Note 1:
The process described in can be performed in any order.
Note 2:
Without completing the process described in , the next process can not be performed.
Note 3:
Illustration of disassembly is omitted.
SET
FRONT PANEL SECTION
(Note 3)
COVER
(Note 3)
2-2. MECHANISM DECK (MG-25L-136)
(Page 7)
2-3. MAIN BOARD
(Page 8)
2-4. HEAT SINK (ISO)
(Page 8)
Note:
Follow the disassembly procedure in the numerical order given.
2-2.
MECHANISM DECK (MG-25L-136)
6 mechanism deck
(MG-25L-136)
4 connector (CN351)
5 screw (PTT2.6
×
6)
3 flexible board
(CNP301)
2 sub panel assy
1 screw (PTT2.6
×
6)
1 four screws
(PTT2.6
×
6)
7
XR-CA430X/CA440
2-3.
MAIN BOARD
2 two ground point screws (PTT2.6
×
6)
3 rubber cap (25)
1 screw (PTT2.6
×
10)
4 main board
1 two screws
(PTT2.6
×
10)
2-4.
HEAT SINK (ISO)
2 heat sink (ISO)
1 seven screws
(PTT2.6
×
10)
8
SECTION 3
ASSEMBLY
• This set can be assembled in the order shown below.
3-1.
ASSEMBLY FLOW
3-2. HOUSING
(Page 10)
3-3. ARM (SUCTION)
(Page 10)
3-4. LEVER (LDG-A)/(LDG-B)
(Page 11)
3-5. GEAR (LDG-FT)
(Page 11)
3-6. GUIDE (C)
(Page 12)
3-7. MOUNTING POSITION OF
CAPSTAN/REEL MOTOR (M901)
(Page 12)
XR-CA430X/CA440
9
XR-CA430X/CA440
Note:
Follow the assembly procedure in the numerical order given.
3-2.
HOUSING
5 Fit projection on C part.
2
Install the hanger onto two claws of the housing.
4 Fit claw on B part.
7
Hold the hanger by bending the claw.
1
Install the catch to the hanger. hanger
3
Put the housing
under A part.
6 Fit projection on D part.
housing
C
part
8
Hold the hanger by bending the claw.
D
part
A
part
B
part
3-3.
ARM (SUCTION)
2
Move the arm (suction) in the arrow direction and fit on projection.
projection
1
Fit the arm (suction) on the shaft.
10
3-4.
LEVER (LDG-A) / (LDG-B)
shaft A
shaft B
shaft C
XR-CA430X/CA440
shaft A
shaft B
1
Fit the lever (LDG-A) on
shafts A – C and install it.
3
type-E stop ring 2.0
2
Fit the lever (LDG-B) on
shafts A and B and
install it.
3-5.
GEAR (LDG-FT)
gear (LDG-D) hole
5
gear (LDG-FT) hole lever (LDG-A) gear (LDG-FB)
4
Align hole in the gear (LDG-D) with hole the lever (LDG-A).
6
polyethylene washer
2
tension spring (LD-2)
1
2
tension spring (LD-1)
3
Move the lever (LDG-B) in the arrow direction.
11
XR-CA430X/CA440
3-6.
GUIDE (C)
2
guide (C)
1
three claws
3-7.
MOUNTING POSITION OF CAPSTAN/REEL MOTOR (M901)
Note: Mount the motor so that the angle between of the motor and the hole for the screw becomes 30
°
as shown in this figure.
two precision screws
(P2
×
2) capstan/reel motor
(M901)
30˚
12
SECTION 4
MECHANICAL ADJUSTMENTS
1. Clean the following parts with a denatured-alcohol-moistened swab: playback head pinch roller rubber belt idler capstan
2. Demagnetize the playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. The adjustments should be performed with the power supply voltage (14.4 V) unless otherwise noted.
TORQUE MEASUREMENT
Mode Torque Meter
Forward
Forward
Back Tension
Reverse
Reverse
Back Tension
FF, REW
CQ-102C
CQ-102C
CQ-102RC
CQ-102RC
CQ-201B
Meter Reading
2.95 – 6.37 mN•m
(30 – 65 g•cm)
(0.42 – 0.90 oz•inch)
0.05 – 0.44 mN•m
(0.5 – 4.5g•cm)
(0.01 – 0.06 oz•inch)
2.95 – 6.37 mN•m
(30 – 65 g•cm)
(0.42 – 0.90 oz•inch)
0.05 – 0.44 mN•m
(0.5 – 4.5g•cm)
(0.01 – 0.06 oz•inch)
5.89 – 19.61 mN•m
(60 – 200 g•cm)
(0.83 – 2.78 oz•inch)
TAPE TENSION MEASUREMENT
Mode Tension Meter
Forward
Reverse
CQ-403A
CQ-403R
Meter Reading more than 60 g
(more than 2.12 oz) more than 60 g
(more than 2.12 oz)
XR-CA430X/CA440
SECTION 5
ELECTRICAL ADJUSTMENTS
TAPE DECK SECTION
0 dB=0.775 V
TAPE SPEED ADJUSTMENT
Setting:
test tape
WS-48A
(3 kHz, 0 dB) frequency counter
10 k
Ω set
+
–
AUDIO OUT REAR jack (CNJ151)
Procedure:
1. Put the set into the FWD PB mode.
2. Adjust adjustment resistor for inside capstan motor so that the reading on the frequency counter becomes 3,000 Hz.
Specification: Constant speed
Frequency counter
2,955 to 3,075 Hz
Adjustment Location:
– SET UPPER VIEW –
Tape Speed Adjustment
TUNER SECTION
Tuner section adjustments are done automatically in this set.
13
XR-CA430X/CA440
SECTION 6
DIAGRAMS
6-1.
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:
•
X
: parts extracted from the component side.
•
Y
: parts extracted from the conductor side.
• : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side: Parts on the pattern face side seen from
(Conductor Side) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(Component Side) the parts face are indicated.
Note on Schematic Diagram:
• All capacitors are in
µ
F unless otherwise noted. pF:
µµ
F
50 WV or less are not indicated except for electrolytics and tantalums.
• All resistors are in
Ω
and
1
/
4
W or less unless otherwise specified.
•
C
: panel designation.
• A : B+ Line.
• Power voltage is dc 14.4V and fed with regulated dc power supply from ACC and BATT cords.
• Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions.
no mark : FM
(
〈〈
) : MW/LW
〉〉
: TAPE PLAYBACK
∗
: Impossible to measure
• Voltages are taken with a VOM (Input impedance 10 M
Ω
).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F
: FM f
: MW/LW
E
: TAPE PLAYBACK
L
: BUS AUDIO IN
• Waveforms
– MAIN Board –
1 IC51
4
(OSCO) 3 IC501 qh
(XOUT)
5 Vp-p
2.3 Vp-p
232 ns
2 IC501 qs
(OSCOUT)
30.8
µ s
– KEY Board –
4 IC901 y;
(OSC)
3.4 Vp-p
2.6 Vp-p
54.4 ns
27.4
µ s
14
• IC Block Diagrams
– MAIN Board –
IC51 SAA6588T-118
20
19
18 17 16 15 14 13
MULTI
PATH
DETECTOR
POWER SUPPLY
& RESET
57kHz
8th ORDER
BAND-PASS FILTER
CLOCKED
COMPARATOR
RDS/RDBS
DEMODULATOR
TEST
CONTROL
RDS/RDBS
DECODER
CLOCK
SIGNAL QUALITY
DECODER
4 5
4
INTERFACE
REGISTER
DATA
OSCILLATOR
& CLOCK
CLOCK
DATA
IIC BUS SLAVE
TRANSCEIVER
PAUSE
DETECTOR
12 11
1 2 3 4 5 6 7 8 9 10
IC301 CXA2509AQ-T4
PBFB2
PBRIN2
31
32
PBREF2
33
PBFIN2
34
VCT
PBGND
35
36
PBFIN1 37
PBREF1 38
PBRIN1
PBFB1
39
40
30
VCT
29 28 27 26
120
µ
/70
µ
T2
– +
F2
F1
X1
+
X1
25
NR BIAS
TAPE/AUX
TAPE EQ
LPF
FWD/RVS
VCC
+
–
F3
24 23 22 21
24dB
+ –
MS
MODE
20
19
18
17
16
MSMODE
DRSW
TAPESW
INSW
NC
MS ON/
OFF
DETECT
15 NC
14 MSOUT
13 DGND
–
+
T1
+ –
12 MSTC
11 G1FB
1
120
µ
/70
µ
2 3 4 5 6 7
24dB
8 9 10
XR-CA430X/CA440
15
XR-CA430X/CA440
IC331 TDA7402TR
ACINLF
SWINR
SWINL
34
35
36
ACOUTR
ACOUTL
37
38
CREF
39
33 32 31
ACIN
OUTPUT
SELECTOR
MAIN
SECOND
FRONT
REAR
SW
30 29 28 27
MONO-
FADER
MONO-
FADER
MIXER
MONO-
FADER
MONO-
FADER
26 25
MONO-
FADER
MONO-
FADER
SUBWOOFER
+PHASE
CONTROL
24 23
LP
HP
VOICE
BANDPASS
BASS
TREBLE
VOLUME
SOFTMUTE
LOUDNESS
COMPANDER
LOUDNESS
MUX 40
IN-GAIN
+
IN-GAIN
+AUTO ZERO
MUTE
MD1
MD1G
41
42
MD2
MD2G
43
44
MAIN SOURCE
SELECTOR
MIXING
SELECTOR
SECOND SOURCE
SELECTOR
MAIN
INPUT
MULTIPLEXER
FM
PHONO
MAIN CH0 AUX
AM
1 2 3 4 5 6 7 8 9 10 11
SUPPLY
HIGH-CUT
S&H
25kHz
LP
PULSE
FORMER
QUAL
BEEP
DEMODULATOR
+STEREO ADJUST
+STEREO BLAND
MULTIPATH
DETECTOR
PILOT
CANCELATION
PIL DET
D/A
CONVERTER
PLL
80kHz
LP
AM/FM
NOISE BLANKER
22 VDD
21
20
SCL
SDA
19 GND
18 SM
17 QUAL
16 MPOUT
15 MPIN
14 LEVEL
13 MPX
12
AMIF
16
IC351 LB1930M-TLM
VCC
NC
1
2
IN1
3
BUFFER
IN2
4
BUFFER
S-GND 5
CONTROL
CIRCUIT
MOTOR
DRIVE
CIRCUIT
10
NC
9
8
7
OUT1
NC
OUT2
6 P-GND
IC581 MM1175XFF
BUS ON
OUT
1
RESET
OUT
2
BATT 3
CLK
OUT
4
RESET
SWITCH
BATT
SWITCH
VREF 5
DATA
IN/OUT
6
GND
7
14 VCC
13
RESET
IN
12
BUS ON
IN
11
CLK
IN
10
BATT
CHECK
9 DATA IN
8 DATA OUT
IC611 BA4908-V3
REGULATOR
1 2 3 4
–
+
OVER VOLTAGE
PROTECT
5 6 7 8 9
–
+
10
+
– –
+
11 12
17 17
XR-CA430X/CA440
XR-CA430X/CA440
6-2.
PRINTED WIRING BOARD – MAIN Board –
BUS AUDIO
IN
AUDIO OUT
REAR
(CA440)
REMOTE IN
IC90
C331
+
(CA440)
IC301
C510
(CA440)
(CA430X)
(CA440)
IC751
16 15 14 13 9 10 11 12 6 5 18 17
8
4
7
IC581
BUS CONTROL
IN
18
17
10
9
CN781
(FRONT VIEW)
11 13 15
12
4
14
5
6
16
7
8
F781
IC611
18
17
9 11 13
10 12 14
4
5
6
VIO
GRY
WHT
GRN
REAR RCH+
FRONT RCH+
FRONT LCH+
REAR LCH+
15
16
GRN/BLK
WHT/BLK
GRY/BLK
VIO/BLK
REAR LCH–
FRONT LCH–
FRONT RCH–
REAR RCH–
BLU
BLU/WHT
TEL ATT
AMP REM
BLU
RED
ANT REM
ACC
7
8
BLK
YEL
GND
BATT
IC551
IC351
• Semiconductor Location
Ref. No.
Location
D708
D709
D710
D721
D722
D723
D724
D731
D732
D613
D614
D622
D703
D704
D705
D706
D707
D552
D553
D581
D582
D585
D586
D610
D611
D1
D51
D55
D90
D91
D92
D351
D352
K-3
K-3
K-2
D-9
D-9
D-9
C-8
D-8
C-8
D-10
D-10
D-8
K-3
K-3
K-4
K-4
K-3
F-12
H-5
E-12
D-13
D-12
B-13
E-12
E-12
F-5
H-5
J-7
F-2
F-3
I-5
H-12
G-13
Ref. No.
Location
D733
D734
D781
C-10
D-9
D-11
Q353
Q354
Q551
Q571
Q581
Q583
Q601
Q602
Q621
Q622
Q90
Q91
Q171
Q181
Q271
Q281
Q351
Q352
IC51
IC90
IC301
IC331
IC351
IC501
IC551
IC581
IC611
IC751
J-2
E-2
G-4
D-4
I-13
I-7
K-10
D-11
F-14
A-7
H-12
G-12
I-10
H-10
E-12
G-9
J-13
J-13
D-7
D-7
I-5
F-2
B-5
B-4
B-5
B-4
H-12
I-12
18 18
6-3.
SCHEMATIC DIAGRAM – MAIN Board (1/3) – •
See page 14 for Waveform.
•
See page 15 for IC Block Diagrams.
XR-CA430X/CA440
19 19
XR-CA430X/CA440
6-4.
SCHEMATIC DIAGRAM – MAIN Board (2/3) – •
See page 14 for Waveforms.
•
See page 15 for IC Block Diagrams.
20 20
6-5.
SCHEMATIC DIAGRAM – MAIN Board (3/3) – •
See page 15 for IC Block Diagrams.
21 21
XR-CA430X/CA440
G
H
• Semiconductor
Location
Ref. No.
Location
D901
D991
G-10
F-9
IC901 F-7
LED902 C-1
LED903 C-2
LED906 C-1
LED922 C-13
LED923 C-14
LED940 C-12
LED950 C-3
XR-CA430X/CA440
6-6.
PRINTED WIRING BOARD – KEY Board –
1 2 3
A
KEY BOARD
(COMPONENT SIDE)
B
C
D
E
4 5 6 7 8 9 10 11 12 13 14
+
ATT
LED902, 903, 922,
923, 940, 950
A K
A K A K
VOL
(ILLUMINATION)
MODE
A
SOURCE
K
−
S2
K1
SEL
S1
A1
1
LCD901
LIQUID CRYSTAL DISPLAY
A1
S1
AE
K1
S2
A1
S1
BTM
SENS
K1
S2
A1
S1
−
1
DISC
K1
S2
A1
S1
+
2
K1
S2
A1
S1
REP
3
K1
S2
A1
S1
SHUF
4
K1
S2
A1
S1
−
BL SKIP
5
K1
S2
ALBM
A1
S1
+
ATA
6
K1
S2
A1
S1
MTL
PTY
K1
S2
50
(ILLUMINATION)
SEEK
AMS
A K
D-BASS
A K
MBP
S2
K1
TA
S1
A1
A1
S1
DSPL
K1
S2
OFF
A1
S1
K1
S2
11
(11)
KEY BOARD
(CONDUCTOR SIDE)
F
PL901
(LCD BACK LIGHT)
PL902
(LCD BACK LIGHT)
K K
K A K
22 22
1-683-350-
11
(11)
XR-CA430X/CA440
6-7.
SCHEMATIC DIAGRAM – KEY Board – •
See page 14 for Waveform.
GND
GND
NC
GND
KEY-1
KEY-0
CE-LCD
DATA-LCD
CLK-LCD
+B
+B
PANEL
CN901
12P
LSW900(1/2)
OFF
SOURCE
VOL
+
ATT
VOL
-
MODE
ALBM +
ATA
6
AE
BTM
SENS
DISC -
1
DISC +
2
ALBM -
BL SKIP
5
REP
3
SHUF
4
LSW901(1/2)
S902
LSW903(1/2)
LSW904(1/2)
LSW905(1/2)
S906
LSW907(1/2)
LSW908(1/2)
LSW909(1/2)
LSW910(1/2)
LSW911(1/2)
LSW912(1/2)
LSW913(1/2)
LSW914(1/2)
R996 1k
R998 1k
R997 1k
D901
UMZ6.8ENTR
CE
DI
CL
R931
1.5k
R941
1.5k
R951
1.5k
R932
680
R942
680
R952
680
R933
680
R943
680
R953
680
R934
680
R944
680
R954
680
R935
680
R945
680
R955
680
R936
680
R946
680
R956
680
R937
680
R947
680
R957
680
R990
2.2k
R991
2.2k
R992
2.2k
PL901
(LCD BACK LIGHT)
LSW900(2/2)
R919
∗
R929
∗
R939
∗
LSW920(2/2)
∗ R919,929,939
10 (CA440)
22 (CA430X)
LED940
CL-190FG (CA440)
CL-190SR (CA430X)
(ILLUMINATION)
LSW923(2/2)
PL902
(LCD BACK LIGHT)
LSW925(2/2)
LSW901(2/2)
LSW926(2/2)
LSW927(2/2)
LSW908(2/2)
LSW909(2/2)
LSW910(2/2)
LSW911(2/2)
LSW913(2/2)
LSW914(2/2)
LSW912(2/2)
LSW907(2/2)
LSW903(2/2)
LSW904(2/2)
LED950
∗
LED902
∗
∗
LED902,903
CL-190PG (CA440)
CL-190SR (CA430X)
SOURCE
LED903
∗
∗
LED906
CL-190FG (CA440)
CL-190SR (CA430X)
MODE
LED906
∗
∗
LED950
CL-190FG (CA440)
CL-190SR (CA430X)
(ILLUMINATION)
LSW905(2/2) LSW921(2/2)
R981
470
LED922
∗
∗
R967
680
R977
680
R987
680
R995
1M
R994
330k
C994
100p
∗
D991
UDZ-TE-17-4.7B (CA440)
UDZ-TE-17-5.1B (CA430X)
R999
0
D991
∗
C991
0.022
C992
0.1
C993
0.1
R983 1k
R984 1k
R985 1k
SEG47
SEG48
SEG49
COM1
COM2
COM3
COM4
LED923
LSW924(2/2)
R980
1k
CE
CL
DI
∗
LED922,923
CL-190PG (CA440)
CL-190SR (CA430X)
D-BASS
C995 0.22
R910
6.8k
R911
10k
R912
15k
R913
22k
R914
47k
R901
680
R921
680
R902
680
R922
680
R903
680
R923
680
R904
1k
R924
1k
R905
1.5k
R925
1.5k
R906
1.5k
R926
1.5k
R907
2.2k
R927
2.2k
R908
3.3k
R909
4.7k
SEEK AMS
LSW920(1/2)
LSW921(1/2)
S922
LSW923(1/2)
LSW924(1/2)
LSW925(1/2)
SEL
D-BASS
SEEK AMS
MBP
DSPL
LSW926(1/2)
LSW927(1/2)
TA
MTL
PTY
LCD901
LIQUID CRYSTAL DISPLAY
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
23 23
XR-CA430X/CA440
6-8.
IC PIN FUNCTION DESCRIPTION
•
MAIN BOARD IC501 MN101C49KSA1 (SYSTEM CONTROLLER)
Pin No.
1
2
3
4
5
14
15
16
17
18
10
11
12
13
8
9
6
7
19
20
21 to 23
24
25
26
27
28
29
30, 31
32
33
34
35
40
41
42
43
36
37
38
39
Pin Name
VREF–
VSM
NIL
KEYIN1
KEYIN0
RCIN0
QUALITY
MPTH
NIL
VREF+
VDD
OSCOUT
OSCIN
VSS
XI
XO
MMOD
LCDSO
LCDCE
LCDCKO
NCO
SYSRST
BUSON
KEYACK
DAVN
BUIN
SIRCS
NIL
NIH
RESET
TUNON
BEEP
PW_ON
NCO
ACCIN
NCO
TELATT
NIH
BUSSO
BUSSI
I/O Description
I
Reference voltage (0V) input terminal (for A/D converter)
I
I
FM and AM signal meter voltage detection signal input from the FM/AM tuner unit (TU1)
(A/D input)
I Not used (fixed at “L”)
I
Key input terminal (A/D input) S907, S908, LSW905 to LSW915
(SEEK/AMS – . m, SEEK/AMS + > M, MBP, D-BASS D, DSPL, MTL PTY, TA,
ATA 6, BL SKIP 5, SHUF 4, REP 3, 2 DISC +, 1 DISC– keys input)
Key input terminal (A/D input) S901 to S906, LSW901 to LSW904 (OFF, SRC SOURCE, +
(VOLUME), – (VOLUME), MODE o, SEL, Z, ATF, BTM SENS, AF keys input)
I Rotary remote commander key input terminal (A/D input) (XR-CA440 only)
I Noise level detection signal input at SEEK mode (A/D input)
I Multi-path detection signal input from the RDS decoder (IC51) (A/D input)
I Not used (fixed at “L”)
I
Reference voltage (+5V) input terminal (for A/D converter)
—
Power supply terminal (+5V)
O Main system clock output terminal (18.432 MHz)
I Main system clock input terminal (18.432 MHz)
—
Ground terminal
I
Sub system clock input terminal (32.768 kHz)
O Sub system clock output terminal (32.768 kHz)
I Selection signal of memory mode input terminal “L”:single chip mode (fixed at “L”)
O Serial data output to the liquid crystal display driver (IC901)
O Chip enable signal output to the liquid crystal display driver (IC901) “H” active
O Serial data transfer clock signal output to the liquid crystal display driver (IC901)
O Not used (open)
O
Reset signal output to the SONY bus interface (IC581) “L”: reset
O Bus on/off control signal output to the SONY bus interface (IC581) “L”: bus on
I
Input of acknowledge signal for the key entry Acknowledge signal is input to accept function and eject keys in the power off status On at input of “H”
I
Synchronized detection signal of RDS data block input from the RDS decoder (IC51)
“H” active
I
Battery detection signal input from the SONY bus interface (IC581)
“L” is input at low voltage
I
SIRCS remote control signal input terminal Not used (open)
I Not used (fixed at “L”)
I Not used (fixed at “H”)
I
System reset signal input from the reset signal generator (IC551) and reset switch (S551)
“L”: reset “L” is input for several 100 msec after power on, then it changes to “H”
O Tuner system power supply on/off control signal output “H”: tuner power on
O Beep sound drive signal output to the power amplifier (IC751)
O Main system power supply on/off control signal output “H”: power on
I Not used (open)
I Accessory detection signal input “L”: accessory on
O Not used (open)
I Telephone attenuate signal input At input of “H”, the signal is attenuated by –20 dB
I Not used (fixed at “H”)
O Serial data output to the SONY bus interface (IC581)
I Serial data input from the SONY bus interface (IC581)
24 24
90
84
85
86
87
88
89
Pin No.
44
45
46
47
Pin Name
BUSCKO
IIC SIO
NCO
IIC CKO
48
49
50
51
52
AMPON
AMPATT
ATT
NCO
AMSON
F/ROUT
MTLON
TAPATT
NCO
AMSIN
NCO
VOLATT
NCO
FLASH_W
TESTIN
RCIN1
NCO
EEP SIO
EEP CKO
COLSEL
NCO
57
58
59
60 to 64
65
66
67
68 to 73
74
75
76
77 to 81
53
54
55
56
82 AD ON
83
ILLON
REL
POS3
POS2
POS0
POS1
LMLOD
LMEJ
I/O Description
O Serial data transfer clock signal output to the SONY bus interface (IC581)
I/O
Two-way data IIC bus with the FM/AM tuner unit (TU1), RDS decoder (IC51) and electrical volume (IC331)
O Not used (open)
O
IIC bus clock signal output to the FM/AM tuner unit (TU1), RDS decoder (IC51) and electrical volume (IC331)
O
Standby on/off control signal output to the power amplifier (IC751)
“L”: standby mode, “H”: amplifier on
O Muting on/off control signal output to the power amplifier (IC751) “L”: muting on
O Audio line muting on/off control signal output “H”: muting on
O Not used (open)
O
Tape auto music sensor control signal output to the CXA2509AQ (IC301)
“L”: auto music sensor on
I
I
I
I
O
Forward/reverse control signal output to the CXA2509AQ (IC301)
“L”: reverse direction, “H”: forward direction
O METAL on/off control signal output to the CXA2509AQ (IC301) “H”: METAL on
O
Tape muting on/off control signal output to the CXA2509AQ (IC301) “H”: muting on
Active at ATA, FF/REW mode
O Not used (open)
I
Whether a music is present or not from CXA2509AQ (IC301) is detected at auto music sensor
“L”: music is present, “H”: music is not present
O Not used (open)
O
Pre amplifier muting on/off control signal output to the electrical volume (IC331)
“L”: muting on
O Not used (open)
I
Internal flash memory data write mode detection signal input terminal “L”: data write mode
Not used (open)
I
I
Setting terminal for the test mode “L”: test mode, normally fixed at “H”
Rotary remote commander shift key input terminal (XR-CA440 only) “L”: shift key on
O Not used (open)
I/O Two-way data bus for tuner EEPROM with the FM/AM tuner unit (TU1)
I/O
Two-way bus clock signal for tuner EEPROM with the FM/AM tuner unit (TU1)
I
Setting terminal for the illumination color
“L”: amber (XR-CA430X: AMBER), “H”: green (XR-CA440: GREEN)
O Not used (open)
O
A/D converter power control signal output terminal
When the KEYACK (pin wh) that controls reference voltage power for key A/D conversion input is active, “L” is output from this terminal to enable the input
O
Power on/off control signal output of the illumination LED and liquid crystal display driver
(IC901) “H”: power on
I
Rotation detection signal input from supply reel sensor and take-up reel sensor on the mechanism deck
Tape position (EJECT/FF/REW/REV/
FWD mode) detect input from the tape operation switch on the deck mechanism
POS3: “L”: REV and EJECT mode, “H”: others mode
POS2: “L”: REW mode, “H”: others mode
POS0: “L”: EJECT mode, “H”: others mode
POS1: “L”: FF and FWD mode, “H”: others mode
O
O
Motor drive signal output to the loading motor drive (IC351) “H” active
(For the loading direction and forward side operation) *1
Motor drive signal output to the loading motor drive (IC351) “H” active
(For the eject direction and reverse side operation) *1
XR-CA430X/CA440
Pin No.
91
92
93
94
95
96 to 99
100
Pin Name
TAPEON
CMON
NOSESW
NS_MASK
DAVSS
NCO
DAVCC
*1 Loading motor control
Mode
Terminal
LMLOD (pin il )
LMEJ (pin o; )
I/O Description
O
Power on/off control signal output of the loading motor drive (IC351) and capstan/reel motor
(M901) “H”: motor on
O
Capstan/reel motor (M901) drive signal output terminal “H”: motor on
I
Front panel block remove/attach detection signal input
“L”: front panel is attached, “H”: front panel is removed
O
Discharge control signal output for the noise detection circuit “H”: discharge
—
Ground terminal (for D/A converter)
O Not used (open)
— Power supply terminal (+5V) (for D/A converter)
STOP
“L”
“L”
LOADING/
FORWARD
“H”
“L”
EJECT/
REVERSE
“L”
“H”
BRAKE
“H”
“H”
25
XR-CA430X/CA440
NOTE:
• -XX and -X mean standardized parts, so they may have some difference from the original one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑ ↑
Parts Color Cabinet's Color
7-1. CHASSIS SECTION
9
SECTION 7
EXPLODED VIEWS
• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Accessories are given in the last of the electrical parts list.
MG-25L-136
#1
F781
15
8
7
main board section
6
#3
10
16
11
12
13
3
4
5
#3
2
#1
1
14
#1
#1 front panel section
Ref. No.
3
4
1
2
5
6
* 7
* 8
9
10
Part No.
Description
3-042-244-11 SCREW (T)
3-224-862-04 PANEL, SUB
X-3370-437-3 LOCK ASSY
3-027-437-51 DOOR, CASSETTE
3-935-003-01 SPRING, TORSION
3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT
3-046-991-01 SPACER (COVER R)
3-046-990-01 SPACER (COVER L)
3-040-995-31 COVER
3-012-859-21 CAP (25), RUBBER
Remark Ref. No.
Part No.
* 11
* 12
* 13
14
15
Description Remark
3-045-878-01 PLATE (TU), GROUND
3-045-877-02 CUSHION (TU)
3-033-846-02 INSULATED PLATE
3-009-813-61 CHASSIS
1-782-381-11 CORD (WITH CONNECTOR) (ISO P&S)
(POWER)
16
F781
#1
#3
1-777-989-41 CORD (WITH CONNECTOR) (AMP REM/ATT)
1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A/32V)
7-685-792-09 SCREW +PTT 2.6X6 (S)
7-685-794-09 SCREW +PTT 2.6X10 (S)
26
XR-CA430X/CA440
7-2. FRONT PANEL SECTION
not supplied
(KEY board)
#4
#4
#4
52
53
60
59
58
57
56
61
LCD901
62
63
64
55
54
66
65
51
Ref. No.
Part No.
51
51
52
53
54
Description Remark
A-3337-043-A PANEL COMPLETE ASSY, FRONT (CA430X)
A-3337-047-A PANEL COMPLETE ASSY, FRONT (CA440)
3-236-597-01 BUTTON (RELEASE)
3-231-816-01 SPRING (RELEASE)
3-236-587-01 PANEL, FRONT (CA430X)
54
55
56
57
58
59
3-236-587-11 PANEL, FRONT (CA440)
3-236-591-01 BUTTON (R) (Z. + > M SEEK AMS m . –. MBP. DSPL. OFF)
3-236-593-01 BUTTON (D-BASS)
3-236-589-01 BUTTON (PRESET)
(AF. SENS. 1. 2. 3. 4. 5. 6. PTY. TA)
3-236-590-01 BUTTON (L) (ATT. + VOL –. MODE. SEL)
3-236-592-01 BUTTON (SOURCE)
Ref. No.
Part No.
60
61
61
62
63
Description
3-236-596-01 PLATE (LCD), GROUND
3-236-598-01 ILLUMINATOR (LCD) (CA430X)
3-236-598-11 SHEET (ILLUMINATOR) (CA440)
3-236-595-01 PLATE (LCD), LIGHT GUIDE
3-236-599-01 SHEET (REFLECTOR)
64
65
66
#4
1-694-883-11 CONDUCTIVE BOARD, CONNECTION
3-236-588-01 PANEL, FRONT BACK
X-3378-490-2 CASE (PANEL) ASSY
Remark
LCD901 1-804-622-11 DISPLAY PANEL, LIQUID CRYSTAL (CA430X)
LCD901 1-804-628-11 DISPLAY PANEL, LIQUID CRYSTAL (CA440)
7-685-106-19 SCREW +P 2X10 TYPE2 NON-SLIT
27
XR-CA430X/CA440
7-3. MAIN BOARD SECTION
101
102
103
#2
TU1
#3
#3
104
Ref. No.
Part No.
101
101
* 102
* 103
* 104
Description
A-3340-278-A MAIN BOARD, COMPLETE (CA430X)
A-3340-284-A MAIN BOARD, COMPLETE (CA440)
3-224-902-01 HEAT SINK (REG)
3-040-998-01 BRACKET (IC)
3-224-899-01 HEAT SINK (ISO) (CA440)
Remark Ref. No.
Part No.
* 104
TU1
#2
#3
Description
3-224-899-11 HEAT SINK (ISO) (CA430X)
A-3220-812-A TUNER UNIT (TUX-020)
7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
7-685-794-09 SCREW +PTT 2.6X10 (S)
Remark
28
XR-CA430X/CA440
7-4. MECHANISM DECK SECTION
(MG-25L-136)
160
159
163
158
A
161
HP901
154
155
#6
157
162
156
A
M901
164
153
152
168
not supplied
168
#7
166
167
151
165
Ref. No.
Part No.
151
* 152
* 153
154
155
Description
A-3291-667-A CLUTCH (FR) ASSY
3-019-130-01 LEVER (LDG-A)
3-019-131-05 LEVER (LDG-B)
3-228-690-01 SPRING (LD-1), TENSION
3-020-540-01 SPRING (LD-2), TENSION
156
157
158
* 159
160
161
3-020-542-01 GEAR (LOADING FT)
3-341-753-11 WASHER, POLYETHYLENE
3-020-533-01 HOUSING
3-020-532-01 ARM (SUCTION)
3-020-534-01 HANGER
3-933-346-01 CATCHER
Remark Ref. No.
Part No.
162
163
164
165
166
Description
3-933-344-22 GUIDE (C)
3-927-100-21 SCREW (+PS 2X10), SPECIAL
3-364-151-01 WASHER
A-3220-811-A MECHANISM DECK ASSY
3-017-302-01 BELT (25)
167
168
3-026-636-01 FLYWHEEL (F)
3-701-437-21 WASHER
HP901 1-500-157-21 HEAD, MAGNETIC (PLAYBACK)
M901 A-3291-665-A MOTOR ASSY, MAIN (CAPSTAN/REEL)
#6 7-624-104-04 STOP RING 2.0, TYPE-E
#7 7-627-553-17 PRECISION SCREW +P 2X2 TYPE 3
Remark
29
XR-CA430X/CA440
KEY
NOTE:
• Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set.
• -XX and -X mean standardized parts, so they may have some difference from the original one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
SECTION 8
ELECTRICAL PARTS LIST
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u:
µ
, for example: uA. .
:
µ
A. .
uPB. . :
µ
PB. .
uPD. . :
µ
PD. .
uPA. . : uPC. . :
µ
µ
PA. .
PC. .
• CAPACITORS uF:
µ
F
• COILS uH:
µ
H
When indicating parts by reference number, please include the board.
Ref. No.
Part No.
Description
KEY BOARD
**********
1-694-883-11 CONDUCTIVE BOARD, CONNECTION
3-236-595-01 PLATE (LCD), LIGHT GUIDE
3-236-596-01 PLATE (LCD), GROUND
3-236-598-01 ILLUMINATOR (LCD) (CA430X)
3-236-598-11 SHEET (ILLUMINATOR) (CA440)
Remark Ref. No.
Part No.
Description Remark
LED940 8-719-038-05 LED CL-190FG-CD-T (ILLUMINATION)
(CA440)
LED940 8-719-061-16 LED CL-190SR-CD-T (ILLUMINATION)
(CA430X)
LED950 8-719-038-05 LED CL-190FG-CD-T (ILLUMINATION)
(CA440)
LED950 8-719-061-16 LED CL-190SR-CD-T (ILLUMINATION)
(CA430X)
3-236-599-01 SHEET (REFLECTOR)
< CAPACITOR >
C991 1-164-227-11 CERAMIC CHIP 0.022uF
10% 25V
C992 1-107-826-11 CERAMIC CHIP 0.1uF
10% 16V
C993 1-107-826-11 CERAMIC CHIP 0.1uF
C994 1-162-927-11 CERAMIC CHIP 100PF
10%
5%
16V
50V
C995 1-127-715-11 CERAMIC CHIP 0.22uF
10% 16V
< SWITCH >
LSW900 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (Z)
(CA430X)
LSW900 1-786-124-11 SWITCH, KEY BOARD (WITH LED) (Z)
(CA440)
LSW901 1-771-883-11 SWITCH, TACTILE (WITH LED) (OFF) (CA430X)
LSW901 1-786-113-11 SWITCH, TACT (WITH LED) (OFF) (CA440)
LSW903 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (VOL +)
(CA430X)
< CONNECTOR >
CN901 1-794-312-11 PIN, CONNECTOR 12P
< DIODE >
D901 8-719-085-72 DIODE UMZ6.8ENTR
D991 8-719-056-79 DIODE UDZ-TE-17-4.7B (CA440)
D991 8-719-976-99 DIODE UDZ-TE-17-5.1B (CA430X)
< IC >
IC901 8-759-365-90 IC LC75824W
< LIQUID CRYSTAL DISPLAY >
LCD901 1-804-622-11 DISPLAY PANEL, LIQUID CRYSTAL (CA430X)
LCD901 1-804-628-11 DISPLAY PANEL, LIQUID CRYSTAL (CA440)
< LED >
LSW903 1-786-124-11 SWITCH, KEY BOARD (WITH LED) (VOL +)
(CA440)
LSW904 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (ATT)
(CA430X)
LSW904 1-786-124-11 SWITCH, KEY BOARD (WITH LED) (ATT)
(CA440)
LSW905 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (VOL –)
(CA430X)
LSW905 1-786-124-11 SWITCH, KEY BOARD (WITH LED) (VOL –)
(CA440)
LSW907 1-771-883-11 SWITCH, TACTILE (WITH LED)
(ALBM +, ATA, 6) (CA430X)
LSW907 1-786-113-11 SWITCH, TACT (WITH LED) (ALBM +, ATA, 6)
(CA440)
LSW908 1-771-883-11 SWITCH, TACTILE (WITH LED) (AE) (CA430X)
LSW908 1-786-113-11 SWITCH, TACT (WITH LED) (AE) (CA440)
LSW909 1-771-883-11 SWITCH, TACTILE (WITH LED) (BTM, SENS)
(CA430X)
LED902 8-719-038-07 LED CL-190PG-CD-T (SOURCE) (CA440)
LED902 8-719-061-16 LED CL-190SR-CD-T (SOURCE) (CA430X)
LED903 8-719-038-07 LED CL-190PG-CD-T (SOURCE) (CA440)
LED903 8-719-061-16 LED CL-190SR-CD-T (SOURCE) (CA430X)
LED906 8-719-038-05 LED CL-190FG-CD-T (MODE o) (CA440)
LED906 8-719-061-16 LED CL-190SR-CD-T (MODE o) (CA430X)
LED922 8-719-038-07 LED CL-190PG-CD-T (D-BASS) (CA440)
LED922 8-719-061-16 LED CL-190SR-CD-T (D-BASS) (CA430X)
LED923 8-719-038-07 LED CL-190PG-CD-T (D-BASS) (CA440)
LED923 8-719-061-16 LED CL-190SR-CD-T (D-BASS) (CA430X)
LSW909 1-786-113-11 SWITCH, TACT (WITH LED) (BTM, SENS)
(CA440)
LSW910 1-771-883-11 SWITCH, TACTILE (WITH LED) (DISC –, 1)
(CA430X)
LSW910 1-786-113-11 SWITCH, TACT (WITH LED) (DISC –, 1)
(CA440)
LSW911 1-771-883-11 SWITCH, TACTILE (WITH LED) (DISC +, 2)
(CA430X)
LSW911 1-786-113-11 SWITCH, TACT (WITH LED) (DISC +, 2)
(CA440)
30
XR-CA430X/CA440
Ref. No.
Part No.
Description Remark
LSW912 1-771-883-11 SWITCH, TACTILE (WITH LED)
(ALBM –, BL SKIP, 5) (CA430X)
LSW912 1-786-113-11 SWITCH, TACT (WITH LED)
(ALBM –, BL SKIP, 5) (CA440)
LSW913 1-771-883-11 SWITCH, TACTILE (WITH LED) (REP, 3)
(CA430X)
LSW913 1-786-113-11 SWITCH, TACT (WITH LED) (REP, 3) (CA440)
LSW914 1-771-883-11 SWITCH, TACTILE (WITH LED) (SHUF, 4)
(CA430X)
Ref. No.
Part No.
Description
R923 1-216-819-11 METAL CHIP
R924 1-216-821-11 METAL CHIP
R925
R926
R927
R929
R929
1-216-823-11 METAL CHIP
1-216-823-11 METAL CHIP
1-216-825-11 METAL CHIP
1-216-797-11 METAL CHIP
1-216-801-11 METAL CHIP
680
1K
1.5K
1.5K
2.2K
10
22
5%
5%
5%
5%
5%
5%
5%
KEY
Remark
1/16W
1/16W
LSW914 1-786-113-11 SWITCH, TACT (WITH LED) (SHUF, 4) (CA440)
LSW920 1-771-476-11 SWITCH, KEY BOARD (WITH LED)
(SEEK AMS M >) (CA430X)
LSW920 1-786-124-11 SWITCH, KEY BOARD (WITH LED)
(SEEK AMS M >) (CA440)
LSW921 1-771-883-11 SWITCH, TACTILE (WITH LED) (SEL) (CA430X)
LSW921 1-786-113-11 SWITCH, TACT (WITH LED) (SEL) (CA440)
LSW923 1-771-476-11 SWITCH, KEY BOARD (WITH LED)
(SEEK AMS m .) (CA430X)
LSW923 1-786-124-11 SWITCH, KEY BOARD (WITH LED)
(SEEK AMS m .) (CA440)
LSW924 1-771-476-11 SWITCH, KEY BOARD (WITH LED) (MBP)
(CA430X)
LSW924 1-786-124-11 SWITCH, KEY BOARD (WITH LED) (MBP)
(CA440)
LSW925 1-771-883-11 SWITCH, TACTILE (WITH LED) (DSPL)
(CA430X)
R931
R932
R933
R934
R935
1-216-823-11 METAL CHIP
1-216-819-11 METAL CHIP
1-216-819-11 METAL CHIP
1-216-819-11 METAL CHIP
1-216-819-11 METAL CHIP
R936 1-216-819-11 METAL CHIP
R937 1-216-819-11 METAL CHIP
R939
R939
R941
1-216-797-11 METAL CHIP
1-216-801-11 METAL CHIP
1-216-823-11 METAL CHIP
1.5k
680
680
680
680
680
680
10
22
1.5k
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
(CA430X)
1/16W
(CA440)
1/16W
LSW925 1-786-113-11 SWITCH, TACT (WITH LED) (DSPL) (CA440)
LSW926 1-771-883-11 SWITCH, TACTILE (WITH LED) (TA) (CA430X)
LSW926 1-786-113-11 SWITCH, TACT (WITH LED) (TA) (CA440)
LSW927 1-771-883-11 SWITCH, TACTILE (WITH LED) (MTL, PTY)
(CA430X)
LSW927 1-786-113-11 SWITCH, TACT (MTL, PTY) (WITH LED)
(CA440)
R942 1-216-819-11 METAL CHIP
R943 1-216-819-11 METAL CHIP
R944 1-216-819-11 METAL CHIP
R945 1-216-819-11 METAL CHIP
R946 1-216-819-11 METAL CHIP
R947
R951
R952
R953
R954
1-216-819-11 METAL CHIP
1-216-823-11 METAL CHIP
1-216-819-11 METAL CHIP
1-216-819-11 METAL CHIP
1-216-819-11 METAL CHIP
680
680
680
680
680
680
1.5k
680
680
680
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
< PILOT LAMP >
PL901 1-518-743-11 LAMP (LCD BACK LIGHT) (CA430X)
PL901 1-518-743-51 LAMP (LCD BACK LIGHT) (CA440)
PL902 1-518-743-11 LAMP (LCD BACK LIGHT) (CA430X)
PL902 1-518-743-51 LAMP (LCD BACK LIGHT) (CA440)
R901
R902
R903
R904
R905
R906
R907
R908
R909
R910
R911
R912
R913
R914
R919
R919
R921
R922
< RESISTOR >
1-216-819-11 METAL CHIP
1-216-819-11 METAL CHIP
1-216-819-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-823-11 METAL CHIP
1-216-823-11 METAL CHIP
1-216-825-11 METAL CHIP
1-216-827-11 METAL CHIP
1-216-829-11 METAL CHIP
1-218-867-11 RES-CHIP
1-216-833-11 METAL CHIP
1-216-835-11 METAL CHIP
1-216-837-11 METAL CHIP
1-216-841-11 METAL CHIP
1-216-797-11 METAL CHIP
1-216-801-11 METAL CHIP
1-216-819-11 METAL CHIP
1-216-819-11 METAL CHIP
680
680
680
1K
1.5K
1.5K
2.2K
3.3K
4.7K
6.8K
10K
15K
22K
47K
10
22
680
680
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
R955 1-216-819-11 METAL CHIP
R956 1-216-819-11 METAL CHIP
R957
R967
R977
1-216-819-11 METAL CHIP
1-216-819-11 METAL CHIP
1-216-819-11 METAL CHIP
680
680
680
680
680
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/10W
R983 1-216-821-11 METAL CHIP
R984 1-216-821-11 METAL CHIP
R985 1-216-821-11 METAL CHIP
R987
R990
1-216-819-11 METAL CHIP
1-216-825-11 METAL CHIP
R991 1-216-825-11 METAL CHIP
R992 1-216-825-11 METAL CHIP
R994 1-216-851-11 METAL CHIP
R995
R996
1-216-857-11 METAL CHIP
1-216-821-11 METAL CHIP
R997 1-216-821-11 METAL CHIP
R998 1-216-821-11 METAL CHIP
R999 1-216-864-11 METAL CHIP
1K
1K
1K
680
2.2K
2.2K
2.2K
330K
1M
1K
1K
1K
0
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
(CA430X)
< SWITCH >
S902 1-771-884-11 SWITCH, TACTILE (WITH LED) (SOURCE)
S906 1-771-884-11 SWITCH, TACTILE (WITH LED) (MODE o)
S922 1-771-884-11 SWITCH, TACTILE (WITH LED) (D-BASS)
**************************************************************
1/16W
(CA440)
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
(CA430X)
1/16W
(CA440)
1/16W
1/16W
1/16W
1/16W
1/16W
31
XR-CA430X/CA440
MAIN
*
*
*
Ref. No.
Part No.
Description
A-3340-278-A MAIN BOARD, COMPLETE (CA430X)
A-3340-284-A MAIN BOARD, COMPLETE (CA440)
*********************
Remark
Ref. No.
Part No.
Description Remark
C183 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C184 1-164-489-11 CERAMIC CHIP 0.22uF
10% 16V
3-040-998-01 BRACKET (IC)
3-224-899-01 HEAT SINK (ISO)
3-224-902-01 HEAT SINK (REG)
7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
7-685-794-09 SCREW +PTT 2.6X10 (S)
C185 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C191 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C192 1-164-315-11 CERAMIC CHIP 470PF
C201 1-162-959-11 CERAMIC CHIP 330PF
C202 1-162-959-11 CERAMIC CHIP 330PF
5%
5%
5%
50V
50V
50V
C1
C2
C3
C4
C5
C6
C7
C8
C13
C14
C22
C23
C24
C52
C53
C54
C55
C57
C58
C59
C60
C61
C62
C63
C64
C90
C92
C93
C94
C95
C96
C97
C98
C99
5%
10%
20%
10%
20%
10%
10%
10%
10%
10%
10%
10%
0.5PF
5%
20%
10%
5%
5%
10%
10%
10%
10%
5%
5%
10%
16V
16V
16V
50V
50V
50V
25V
C104 1-164-489-11 CERAMIC CHIP 0.22uF
10% 16V
C105 1-107-826-11 CERAMIC CHIP 0.1uF
10% 16V
C119
C120
< CAPACITOR >
1-162-918-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
1-126-947-11 ELECT
1-162-968-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
1-124-589-11 ELECT
1-107-823-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
1-109-982-11 CERAMIC CHIP
1-109-982-11 CERAMIC CHIP
1-162-968-11 CERAMIC CHIP
1-164-227-11 CERAMIC CHIP
1-165-176-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
1-162-915-11 CERAMIC CHIP
1-162-919-11 CERAMIC CHIP
1-124-589-11 ELECT
18PF
0.1uF
47uF
0.0047uF 10%
0.1uF
47uF
0.47uF
0.01uF
1uF
1uF
0.0047uF 10%
0.022uF
0.047uF
0.1uF
10PF
22PF
47uF
1-107-826-11 CERAMIC CHIP 0.1uF
1-162-959-11 CERAMIC CHIP 330PF
1-164-505-11 CERAMIC CHIP
1-164-739-11 CERAMIC CHIP
1-162-966-11 CERAMIC CHIP
1-162-964-11 CERAMIC CHIP
1-164-315-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
1-165-176-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
1-162-964-11 CERAMIC CHIP
1-162-959-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
C106 1-126-160-11 ELECT
1-162-915-11 CERAMIC CHIP
1-162-915-11 CERAMIC CHIP
C171 1-124-233-11 ELECT
2.2uF
560PF
0.0022uF 10%
0.001uF
470PF
0.1uF
1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
1-164-315-11 CERAMIC CHIP 470PF
1-162-915-11 CERAMIC CHIP 10PF
1-107-823-11 CERAMIC CHIP 0.47uF
10% 16V
0.047uF
0.1uF
0.1uF
0.001uF
C101 1-162-959-11 CERAMIC CHIP 330PF
C102
C103
330PF
0.01uF
1uF
10PF
10PF
C141 1-126-160-11 ELECT 1uF
C142 1-163-251-11 CERAMIC CHIP 100PF
C174
C175
1-164-489-11 CERAMIC CHIP
1-162-964-11 CERAMIC CHIP
C181 1-124-233-11 ELECT
10uF
0.22uF
0.001uF
10uF
10%
5%
10%
5%
0.5PF
20% 50V
0.5PF
0.5PF
20%
5%
20%
10%
10%
50V
16V
16V
50V
16V
16V
16V
25V
10V
10V
50V
25V
16V
16V
50V
50V
16V
16V
50V
16V
50V
50V
50V
50V
16V
50V
50V
50V
50V
50V
50V
16V
16V
50V
20% 16V
C203 1-162-970-11 CERAMIC CHIP 0.01uF
10% 25V
C204 1-164-489-11 CERAMIC CHIP 0.22uF
10% 16V
C205 1-107-826-11 CERAMIC CHIP 0.1uF
C206 1-126-160-11 ELECT 1uF
10%
20%
16V
50V
C208 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C219
C220
1-162-915-11 CERAMIC CHIP
1-162-915-11 CERAMIC CHIP
C241 1-126-160-11 ELECT 1uF
C242 1-163-251-11 CERAMIC CHIP 100PF
C271 1-124-233-11 ELECT
C274
C275
C281 1-124-233-11 ELECT 10uF
C283 1-163-251-11 CERAMIC CHIP 100PF
C284 1-164-489-11 CERAMIC CHIP 0.22uF
10% 16V
C285
C301
C302 1-131-651-11 TANTALUM CHIP 10uF
C303 1-162-927-11 CERAMIC CHIP 100PF
C304 1-107-826-11 CERAMIC CHIP 0.1uF
C305
C306
C307 1-162-970-11 CERAMIC CHIP 0.01uF
10% 25V
C309 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C331 1-162-970-11 CERAMIC CHIP 0.01uF
10% 25V
C332
C335 20%
50V
16V
C336 1-162-970-11 CERAMIC CHIP 0.01uF
10% 25V
C337 1-124-584-00 ELECT 100uF 20% 10V
C340 1-107-823-11 CERAMIC CHIP 0.47uF
10% 16V
C351
C352
C355 1-124-234-00 ELECT
C356
C357
C504
C505
1-126-934-11 ELECT
1-164-156-11 CERAMIC CHIP
1-162-915-11 CERAMIC CHIP
1-162-918-11 CERAMIC CHIP
0.001uF
22uF
0.47uF
0.01uF
0.0047uF 10%
0.1uF
0.1uF
C353 1-162-974-11 CERAMIC CHIP 0.01uF
C354 1-124-233-11 ELECT 10uF
22uF
C358 1-162-974-11 CERAMIC CHIP 0.01uF
C501 1-124-589-11 ELECT 47uF
C503 1-162-915-11 CERAMIC CHIP 10PF
C506 1-162-919-11 CERAMIC CHIP 22PF
C507 1-162-959-11 CERAMIC CHIP 330PF
C510 1-162-964-11 CERAMIC CHIP 0.001uF
10% 50V
C511
C551
1-164-489-11 CERAMIC CHIP
1-162-964-11 CERAMIC CHIP
1-162-964-11 CERAMIC CHIP
1-124-234-00 ELECT
1-107-823-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
1-162-968-11 CERAMIC CHIP
1-124-233-11 ELECT
1-164-156-11 CERAMIC CHIP
1-164-156-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
1-125-710-11 DOUBLE LAYER
10PF
10PF
10uF
0.22uF
0.001uF
10uF
220uF
0.1uF
10PF
18PF
0.01uF
0.1F
C552 1-126-934-11 ELECT 220uF
C553 1-107-826-11 CERAMIC CHIP 0.1uF
C571 1-126-160-11 ELECT 1uF
0.5PF
0.5PF
20%
5%
20%
10%
10%
20%
5%
10%
20%
20%
5%
10%
10%
10%
20%
20%
20%
20%
0.5PF
0.5PF
5%
5%
5%
10%
20%
10%
20%
50V
50V
50V
50V
16V
16V
50V
16V
50V
50V
16V
16V
50V
16V
16V
25V
25V
25V
50V
16V
16V
16V
25V
50V
16V
50V
50V
50V
50V
50V
25V
5.5V
16V
16V
50V
32
Ref. No.
Part No.
Description
C581 1-162-970-11 CERAMIC CHIP 0.01uF
C584 1-164-156-11 CERAMIC CHIP 0.1uF
C585 1-126-933-11 ELECT
C611 1-126-157-11 ELECT
C615 1-126-157-11 ELECT
100uF
10uF
10uF
Remark
10% 25V
25V
20% 16V
20% 16V
20% 16V
C616 1-126-157-11 ELECT
C617 1-126-157-11 ELECT
C622 1-124-589-11 ELECT
C752 1-136-165-00 FILM
C754 1-124-233-11 ELECT
C902
C903
1-164-489-11 CERAMIC CHIP
1-164-489-11 CERAMIC CHIP
< CONNECTOR >
10uF
10uF
47uF
0.1uF
10uF
0.22uF
0.22uF
20% 16V
20% 16V
20% 16V
5% 50V
20% 16V
C755 1-126-157-11 ELECT
C781 1-107-885-31 ELECT
10uF 20% 16V
3300uF 20% 16V
C782 1-163-009-11 CERAMIC CHIP 0.001uF
10% 50V
C783 1-163-009-11 CERAMIC CHIP 0.001uF
10% 50V
C785 1-163-009-11 CERAMIC CHIP 0.001uF
10% 50V
10% 16V
10% 16V
CN301 1-785-694-11 CONNECTOR, FFC/FPC 7P
CN351 1-784-490-11 CONNECTOR, FFC/FPC 11P
CN581 1-580-907-31 PLUG, CONNECTOR (BUS CONTROL IN)
CN701 1-794-311-21 PLUG, CONNECTOR 12P
CN781 1-794-070-12 PIN, CONNECTOR (ISO)
< JACK >
CNJ151 1-774-699-12 JACK, PIN 4P
(AUDIO OUT REAR, BUS AUDIO IN)
< DIODE >
XR-CA430X/CA440
MAIN
Ref. No.
Part No.
Description
D722 8-719-079-42 DIODE 1ZB22 (TPA3)
D723 8-719-079-42 DIODE 1ZB22 (TPA3)
Remark
D724 8-719-079-42 DIODE 1ZB22 (TPA3)
D731 8-719-079-42 DIODE 1ZB22 (TPA3)
D732 8-719-079-42 DIODE 1ZB22 (TPA3)
D733 8-719-079-42 DIODE 1ZB22 (TPA3)
D734 8-719-079-42 DIODE 1ZB22 (TPA3)
D781 8-719-049-38 DIODE 1N5404TU
< IC >
8-759-492-59 IC SAA6588T/V2-118
IC301 8-752-079-78 IC CXA2509AQ-T4
IC331 8-759-653-27 IC TDA7402TR
IC351 8-759-527-33 IC LB1930M-TLM
IC501 6-801-201-02 IC MN101C49KSA1
IC551 8-759-682-69 IC XC61CN4302MR
IC581 8-759-096-16 IC MM1175XFF
IC611 8-759-661-47 IC BA4908-V3
< JACK >
J1 1-815-185-12 JACK (ANT) (FM/AM ANTENNA IN)
J561 1-566-822-41 JACK (REMOTE IN) (CA440)
< SHORT >
D1
D51
D55
D90
D91
8-719-056-65 DIODE 1SS372-TE85L
8-719-404-50 DIODE MA111-TX
8-719-404-50 DIODE MA111-TX
8-719-404-50 DIODE MA111-TX
8-719-404-50 DIODE MA111-TX
D92 8-719-976-99 DIODE UDZ-TE-17-5.1B
D351 8-719-977-22 DIODE UDZ-TE-17-9.1B
D352 8-719-970-02 DIODE 1SR139-400T-32
D552 8-719-067-56 DIODE MA112-TX
D553 8-719-404-50 DIODE MA111-TX (CA440)
D581 8-719-056-93 DIODE UDZ-TE-17-18B
D582 8-719-056-82 DIODE UDZ-TE-17-6.2B
D585 8-719-072-70 DIODE MA2ZD14001S0
D586 8-719-056-93 DIODE UDZ-TE-17-18B
D610 8-719-970-02 DIODE 1SR139-400T-32
D611 8-719-970-02 DIODE 1SR139-400T-32
D613 8-719-970-02 DIODE 1SR139-400T-32
D614 8-719-970-02 DIODE 1SR139-400T-32
D622 8-719-404-50 DIODE MA111-TX
D703 8-719-109-97 DIODE MA4068-M (TA)
JC1
JC3
JC4
JC5
JC6
1-216-295-00 SHORT
1-216-295-00 SHORT
1-216-296-11 SHORT
1-216-296-11 SHORT
1-216-296-11 SHORT
JC7
JC8
1-216-296-11 SHORT
1-216-296-11 SHORT
JC9 1-216-296-11 SHORT
JC10 1-216-295-00 SHORT
JC11 1-216-295-00 SHORT
JC12 1-216-296-11 SHORT
JC14 1-216-296-11 SHORT
JC15 1-216-296-11 SHORT
JC17 1-216-296-11 SHORT
JC18 1-216-295-00 SHORT
JC50 1-216-296-11 SHORT
JC51 1-216-296-11 SHORT
JC53 1-216-296-11 SHORT
JC54 1-216-295-00 SHORT
JC90 1-216-295-00 SHORT
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
D704 8-719-109-97 DIODE MA4068-M (TA)
D705 8-719-109-97 DIODE MA4068-M (TA)
D706 8-719-034-94 DIODE MA4180-M (TA)
D707 8-719-109-97 DIODE MA4068-M (TA)
D708 8-719-109-97 DIODE MA4068-M (TA)
D709 8-719-109-97 DIODE MA4068-M (TA)
D710 8-719-109-97 DIODE MA4068-M (TA)
D721 8-719-079-42 DIODE 1ZB22 (TPA3)
JC106 1-216-295-00 SHORT
JC301 1-216-295-00 SHORT
JC302 1-216-295-00 SHORT
JC331 1-216-295-00 SHORT
JC351 1-216-295-00 SHORT
JC352 1-216-295-00 SHORT
JC353 1-216-295-00 SHORT
JC552 1-216-296-11 SHORT
JC581 1-216-295-00 SHORT
JC588 1-216-295-00 SHORT
JC622 1-216-295-00 SHORT
0
0
0
0
0
0
0
0
0
0
0
33
XR-CA430X/CA440
MAIN
Ref. No.
Part No.
Description
JC623 1-216-295-00 SHORT
JC701 1-216-295-00 SHORT
JC702 1-216-295-00 SHORT
JC751 1-216-296-11 SHORT
JC752 1-216-296-11 SHORT
JC753 1-216-295-00 SHORT
JC754 1-216-296-11 SHORT
JC755 1-216-296-11 SHORT
JC759 1-216-296-11 SHORT
JC761
JC762
JC763
JC764
JC765
1-216-295-00 SHORT
1-216-295-00 SHORT
1-216-296-11 SHORT
1-216-296-11 SHORT
1-216-295-00 SHORT
JC766 1-216-296-11 SHORT
JC767 1-216-295-00 SHORT
< COIL >
L501
L502
L781
1-410-501-11 INDUCTOR
1-410-501-11 INDUCTOR
1-419-476-11 INDUCTOR
< TRANSISTOR >
2.2uH
2.2uH
250uH
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Remark
Ref. No.
Part No.
R12
R13
R21
R51
R52
R1
R2
R3
R8
R9
R53
R54
R55
R56
R59
Q90
Q91
8-729-027-59 TRANSISTOR
8-729-120-28 TRANSISTOR
Q171 8-729-920-21 TRANSISTOR
Q181 8-729-920-21 TRANSISTOR
Q271 8-729-920-21 TRANSISTOR
Q281 8-729-920-21 TRANSISTOR
Q351 8-729-015-11 TRANSISTOR
Q352 8-729-047-76 TRANSISTOR
Q353 8-729-900-53 TRANSISTOR
Q354 8-729-106-60 TRANSISTOR
Q551 8-729-027-23 TRANSISTOR
Q571 8-729-120-28 TRANSISTOR
Q581 8-729-900-53 TRANSISTOR
Q583 8-729-120-28 TRANSISTOR
Q601 8-729-106-60 TRANSISTOR
Q602 8-729-900-53 TRANSISTOR
Q621 8-729-027-23 TRANSISTOR
Q622 8-729-900-53 TRANSISTOR
< RESISTOR >
DTC144EKA-T146
2SC2412K-T-146-QR
DTC314TK-T-146
DTC314TK-T-146
DTC314TK-T-146
DTC314TK-T-146
2SD1802FAST-TL
FMC2A-T148
DTC114EKA-T146
2SB1132-T100-R
DTA114EKA-T146
2SC2412K-T-146-QR
DTC114EKA-T146
2SC2412K-T-146-QR
2SB1132-T100-R
DTC114EKA-T146
DTA114EKA-T146
DTC114EKA-T146
1-216-809-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-837-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-841-11 METAL CHIP
1-216-845-11 METAL CHIP
1-218-867-11 RES-CHIP
1-216-809-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-853-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-837-11 METAL CHIP
1-216-817-11 METAL CHIP
1-216-797-11 METAL CHIP
100
100
22K
100
100
47K
100K
6.8K
100
100
470K
1K
22K
470
10
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/10W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
Description
R60
R91
R92
R93
R95
1-216-797-11 METAL CHIP
1-216-825-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-845-11 METAL CHIP
1-216-857-11 METAL CHIP
R96
R97
R98
R99
1-216-809-11 METAL CHIP
1-216-833-11 METAL CHIP
1-216-833-11 METAL CHIP
1-216-825-11 METAL CHIP
R100 1-216-825-11 METAL CHIP
R101 1-216-817-11 METAL CHIP
R102 1-216-851-11 METAL CHIP
R103 1-216-835-11 METAL CHIP
R104 1-216-836-11 METAL CHIP
R141 1-216-833-11 METAL CHIP
R142 1-216-821-11 METAL CHIP
R170 1-216-809-11 METAL CHIP
R171 1-216-809-11 METAL CHIP
R175 1-216-841-11 METAL CHIP
R180 1-216-809-11 METAL CHIP
R181 1-216-809-11 METAL CHIP
R185 1-216-841-11 METAL CHIP
R191 1-249-437-11 CARBON
R192 1-218-867-11 RES-CHIP
R201 1-216-817-11 METAL CHIP
R202 1-216-851-11 METAL CHIP
R203 1-216-835-11 METAL CHIP
R204 1-216-836-11 METAL CHIP
R241 1-216-833-11 METAL CHIP
R242 1-216-821-11 METAL CHIP
R270 1-216-809-11 METAL CHIP
R271 1-216-809-11 METAL CHIP
R275 1-216-841-11 METAL CHIP
R280 1-216-809-11 METAL CHIP
R281 1-216-809-11 METAL CHIP
R285 1-216-841-11 METAL CHIP
R301 1-216-836-11 METAL CHIP
R302 1-216-845-11 METAL CHIP
R303 1-216-828-11 METAL CHIP
R304 1-216-835-11 METAL CHIP
R305 1-216-797-11 METAL CHIP
R306 1-216-849-11 METAL CHIP
R331 1-249-393-11 CARBON
R332 1-216-841-11 METAL CHIP
R335 1-216-809-11 METAL CHIP
R336 1-216-809-11 METAL CHIP
R351 1-216-821-11 METAL CHIP
R352 1-249-383-11 CARBON
R353 1-216-829-11 METAL CHIP
R354 1-216-833-11 METAL CHIP
R500 1-247-807-31 CARBON
R501 1-247-807-31 CARBON
R502 1-216-821-11 METAL CHIP
R507 1-216-821-11 METAL CHIP
R508 1-216-821-11 METAL CHIP
R509 1-216-821-11 METAL CHIP
R511 1-216-833-11 METAL CHIP
100
100
47K
100
100
47K
18K
100K
3.9K
15K
100
47K
47K
6.8K
470
330K
15K
18K
10K
1K
1K
100
100
47K
100
470
330K
15K
18K
10K
10
2.2K
100
100K
1M
100
10K
10K
2.2K
2.2K
100
100
1K
1K
1K
1K
10K
10
220K
10
47K
100
100
1K
1.5
4.7K
10K
Remark
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/4W
1/10W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/4W
1/4W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/4W
1/16W
1/16W
1/16W
1/16W
1/6W
1/16W
1/16W
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
34
Ref. No.
Part No.
Description
R513 1-216-833-11 METAL CHIP
R514 1-216-845-11 METAL CHIP
R516 1-216-845-11 METAL CHIP
R517 1-216-845-11 METAL CHIP
R518 1-216-845-11 METAL CHIP
R520 1-216-845-11 METAL CHIP
R521 1-216-821-11 METAL CHIP
R522 1-216-821-11 METAL CHIP
R523 1-216-821-11 METAL CHIP
R526 1-216-845-11 METAL CHIP
R527 1-216-845-11 METAL CHIP
R528 1-216-845-11 METAL CHIP
R529 1-216-845-11 METAL CHIP
R530 1-216-845-11 METAL CHIP
R531 1-216-845-11 METAL CHIP
R532 1-216-845-11 METAL CHIP
R533 1-216-845-11 METAL CHIP
R535 1-216-845-11 METAL CHIP
R538 1-216-813-11 METAL CHIP
R539 1-216-813-11 METAL CHIP
R543 1-216-845-11 METAL CHIP
R545 1-216-809-11 METAL CHIP
R547 1-247-807-31 CARBON
R550 1-216-841-11 METAL CHIP
R551 1-216-845-11 METAL CHIP
R552 1-216-845-11 METAL CHIP
R555 1-208-806-11 RES-CHIP
R556 1-208-806-11 RES-CHIP
R557 1-247-807-31 CARBON
R559 1-216-845-11 METAL CHIP
R561 1-216-849-11 METAL CHIP
R562 1-208-806-11 RES-CHIP
R562 1-216-845-11 METAL CHIP
100
100K
220K
10K
100K
220
220
100K
100
100
47K
100K
100K
10K
10K
1K
100K
100K
100K
100K
100K
100K
100K
100K
100K
10K
100K
100K
100K
100K
100K
1K
1K
R563 1-216-809-11 METAL CHIP
R564 1-216-809-11 METAL CHIP
R569 1-216-845-11 METAL CHIP
R570 1-216-845-11 METAL CHIP
R571 1-216-829-11 METAL CHIP
R572 1-216-841-11 METAL CHIP
R573 1-249-425-11 CARBON
R576 1-216-845-11 METAL CHIP
R577 1-216-841-11 METAL CHIP
R578 1-216-845-11 METAL CHIP
R580 1-216-809-11 METAL CHIP
R581 1-216-821-11 METAL CHIP
R582 1-216-835-11 METAL CHIP
R583 1-216-809-11 METAL CHIP
R586 1-216-833-11 METAL CHIP
R587 1-216-833-11 METAL CHIP
R588 1-216-821-11 METAL CHIP
R589 1-216-841-11 METAL CHIP
R595 1-216-845-11 METAL CHIP
R603 1-216-825-11 METAL CHIP
100
1K
15K
100
10K
10K
1K
47K
100K
2.2K
4.7K
47K
4.7K
100K
47K
100K
100
100
100K
100K
XR-CA430X/CA440
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
MAIN
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
Remark
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
Ref. No.
R608
R609
R753
R756
R902
R903
R904
Part No.
Description
R604 1-216-833-11 METAL CHIP
R606 1-247-791-11 CARBON
R607 1-247-791-11 CARBON
1-249-399-11 CARBON
1-249-399-11 CARBON
R625 1-216-805-11 METAL CHIP
R701 1-216-809-11 METAL CHIP
R751 1-249-417-11 CARBON
1-249-429-11 CARBON
1-216-222-00 RES-CHIP
R757 1-216-222-00 RES-CHIP
R758 1-216-222-00 RES-CHIP
R760 1-216-222-00 RES-CHIP
1-216-845-11 METAL CHIP
1-216-845-11 METAL CHIP
1-216-845-11 METAL CHIP
10K
22
22
33
33
47
100
1K
10K
10K
10K
10K
10K
100K
100K
100K
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
Remark
1/16W
1/4W
1/4W
1/4W
1/4W
1/16W
1/16W
1/4W
1/4W
1/8W
1/8W
1/8W
1/8W
1/16W
1/16W
1/16W
< SWITCH >
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/4W
S551 1-692-431-21 SWITCH, TACTILE (RESET)
< THERMISTOR >
TH501 1-803-350-21 THERMISTOR, POSITIVE
5%
5%
1/16W
1/16W
5% 1/16W
0.5% 1/10W
0.5% 1/10W
TU1
< TUNER >
A-3220-812-A TUNER UNIT (TUX-020)
< VIBRATOR >
5%
5%
5%
5%
5%
5%
5%
1/4W
1/16W
5% 1/10W
0.5% 1/10W
5%
(CA440)
1/16W
(CA430X)
X51 1-579-242-41 VIBRATOR, CRYSTAL (4.332MHz)
X501 1-781-294-21 VIBRATOR, CRYSTAL (18.432MHz)
X502 1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz)
***********************************************************
MISCELLANEOUS
**************
5%
5%
5%
5%
5%
1/16W
(CA440)
1/16W
(CA440)
1/16W
(CA440)
1/16W
(CA430X)
1/16W
15
16
64
1-782-381-11 CORD (WITH CONNECTOR) (ISO P&S)
(POWER)
1-777-989-41 CORD (WITH CONNECTOR) (AMP REM/ATT)
1-694-883-11 CONDUCTIVE BOARD, CONNECTION
F781 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A/32V)
HP901 1-500-157-21 HEAD, MAGNETIC (PLAYBACK)
1/16W
1/4W
1/16W
1/16W
1/16W
LCD901 1-804-622-11 DISPLAY PANEL, LIQUID CRYSTAL (CA430X)
LCD901 1-804-628-11 DISPLAY PANEL, LIQUID CRYSTAL (CA440)
M901 A-3291-665-A MOTOR ASSY, MAIN (CAPSTAN/REEL)
************************************************************
ACCESSORIES
************
1/16W
1/16W
1/16W
1/16W
1/16W
3-238-147-11 MANUAL, INSTRUCTION (ENGLISH, GERMAN,
FRENCH, ITALIAN, DUTCH)
3-238-149-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
GERMAN, FRENCH, ITALIAN, DUTCH)
***********************************************************
1/16W
1/16W
1/16W
1/16W
1/16W
35
XR-CA430X/CA440
Ref. No.
Part No.
Description
PARTS FOR INSTALLATION AND CONNECTIONS
**************************************
501
502
503
504
505
X-3381-409-1 FRAME ASSY, FITTING
X-3381-148-1 SCREW ASSY (BS2), FITTING
3-236-673-01 COLLAR
3-233-644-02 SPRING, FITTING
1-465-459-21 ADAPTER, ANTENNA
506
507
Remark
1-782-381-11 CORD (WITH CONNECTOR) (ISO P&S)
(POWER)
1-777-989-41 CORD (WITH CONNECTOR) (AMP REM/ATT)
Ref. No.
Part No.
Description
501 502
503
FRAME ASSY
×
1
SCREW, FITTING
×
1
BUSHING
×
1
504
COLLAR
×
1
+K 5X8
×
2
SCREW ASSY (BS2), FITTING
505
SPRING, FITTING
×
2
506
POWER CORD
×
1
507
ADAPTER, ANTENNA
×
1
AMP REM/ATT CORD
×
1
Remark
36
MEMO
XR-CA430X/CA440
37
XR-CA430X/CA440
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page.
Ver.
Date
2002.01
2003.01
Description of Revision
New
Change of Part No. for IC501 on MAIN board
(ECN-CSA06072)

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- cassette player
- FM/MW/LW tuner
- 4-channel power amp
- 45W x 4 max output
- tone controls
- remote control (XR-CA440 only)
- auxiliary input
- power aerial control
- telephone ATT control
- BUS audio control