XY Laser Kam CosmoSphere

XY Laser Kam CosmoSphere
Kam CosmoSphere
Multicolour spinning colour light sphere
M
A
N
U
A
L
V
E
R
S
I
O
N
1
.
0
2 5 - 0 5 - 2 0 1 6
For the latest instruction manual updates and information on the entire Kam range visit:
www.kam.co.uk
Kam products are manufactured by: Lamba plc, Unit 1, Southfields Road, Dunstable, Bedfordshire, United Kingdom LU6 3EJ
Telephone: (+44) (0)1582 690600 • Fax: (+44) (0)1582 690400 • Email: mail@lambaplc.com • Web: www.lambaplc.com
If this product is ever no longer functional please take it to a recycling plant for environmentally friendly disposal.
Due to continuous product development, specifications and appearance are subject to change.
© Copyright Lamba plc. E&OE.
XY Laser
Pan & tilt scanning colour laser
Thank you for purchasing this Kam product, we are sure that it will serve you for many years to come.
To optimise it’s performance, please read these instructions carefully to familiarise yourself with the basic operations of the unit.
Please retain them for future reference.This unit has been tested at the factory before being shipped to you. To prevent or reduce
the risk of electrical shock or fire, do not expose the unit to rain or moisture. To prevent a fire hazard, do not expose the unit to
any naked flame sources. Unplug this apparatus during lightning storms or if it is unlikely to be used for long periods of time.
When installing the unit, please ensure you leave enough space around the unit for ventilation. Slots and openings in the unit are
provided for ventilation to ensure reliable operation of the product and to protect it from overheating. To prevent fire hazard, the
openings should never be blocked or covered.
The unit is powered by the mains, always handle the power cable by the plug. Never pull out the plug by pulling on the cable.
Never touch the power cable when your hands are wet as this could cause an electric shock. Do not tie a knot in the cable. The
power cable should be placed such that it is not likely to be stepped on. A damaged power cable can cause a fire or give you an
electrical shock. Check the power cord periodicaly, if you ever find that it is damaged, replace it before using the unit again.
Contact your retailer for a replacement.
The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area
where this unit is to be used meets the requirements of the unit.
The lightning flash symbol inside a triangle is to alert the user to the presence high voltage within the unit’s enclosure
that may be of sufficient power to constitute a risk of electrical shock to persons. Caution: to prevent the risk of electric
shock, do not attempt to open the unit. No user-serviceable parts inside. Refer all servicing to qualified service
personnel. The exclamation mark inside a triangle is intended to alert the user to the presence of important operating
and maintenance instructions in the literature accompanying the appliance.
Select the installation location of your unit carefully. Avoid placing it in direct sunlight or locations subject to vibration and
excessive dust. Do not use the unit where there are extremes in temperature (do not exceede 40ºC).
Unpacking and safety Please unpack your new product carefully. Your new product should reach you in perfect condition.
Please check that no damage has occurred during transit. If any damage is found, do not operate your unit. Please contact the
retailer you purchased it from immediately. If there is any damage to the mains cable do not use the device. Always disconnect
the unit from the mains supply when carrying out any cleaning of the unit.
Manufacturer declarations
In compliance with the following requirements: RoHS Directive (2002/95/EU) and WEEE Directive (2002/96/EU).
If this product is ever no longer functional please take it to a recycling plant for environmentally friendly disposal.
CE declaration of conformity
R&TTE Directive (1999/5/EU), EMC Directive (2004/108/EU), Low Voltage Directive (2006/95/EU).
The declarations are available on application from certification@lambaplc.com
Before putting the devices into operation, please observe the respective country-specific regulations.
Overhead rigging
Important - the installation must be carried out by qualified service personal only. Improper installation can result in serious
injuries and /or damage to property. Overhead rigging required extensive experience. Working load limits should be respected,
certified installation materials should be used, the installed unit should be inspected regularly for safety.
l
l
l
l
l
l
l
Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing.
Locate the unit in a well ventilated spot, far away from any flammable materials and/or liquids. The fixture must be fixed at
least 50cm from surrounding walls
The device should be installed out of reach of people and outside of areas where persons may walk by or be seated.
Before rigging make sure that the installation area can hold minimum point load of 10 times the device`s weight.
The device should be well fixed; a free swinging mounting is dangerous.
Do not cover any ventilation opening as this may result in overheating
Before first time use, the unit should be inspected for safety. Inspection the unit regularly every year.
Packing list
Lighting unit and bracket
Power cable
Instruction manual
Warranty
AC power
The unit is supplied with a power plug appropriate to its voltage. Should any other connections be required they must be carried
out with the following configuration:
Cable (EU)
Cable (US)
Pin
International
Brown
Black
Live
L
Light blue
White
Neutral
N
Yellow/green
Green
Earth
DMX-512 connection
If you are using a standard DMX controller, you can connect the DMX output of the controller directly to the DMX input of the first
unit in a DMX chain. If you wish to connect a DMX controller with other XLR outputs you will need to use adapter cables.
DMX output
1 = Shield
2 = Signal (-)
3 = Signal (+)
DMX input
Connect the DMX output of the first unit in a DMX chain with the DMX input of the next unit in the chain. Always connect the the
output of one unit with the input of the next unit until all units are connected.
Rear panel features
Key to rear panel features
Number
Feature
Function
1
DMX input
3 pin XLR connector for DMX512 input communication.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
DMX output
Power input
Power output
Power switch
Fuse holder
Power ON LED
DMX IN LED
Auto mode LED
DMX OUT LED
LCD Touchscreen
Display reset button
RETURN button
Menu DOWN button
Menu UP button
ENTER button
3 pin XLR connector for DMX512 output communication.
Mains power input IEC socket
IEC connector socket for connecting multiple units
Switches the unit on and off
For 5A fuse replacement as and when required
Illumination shows unit is in operation
Illumination shows DMX input is connected
Illumination shows unit is in AUTO mode
Illumination shows DMX output is connected
Touchscreen display panel
Rotates display 180° and changes language
Illumination confirms unit is in Master mode
Illumination confirms unit is in sound to light mode
Selects chosen function
Function setting
This unit uses a very unique LED Colour touchscreen display. Functions can either be selected by pressing gently on the
touchscreen or by using the menu keys to the right hand side of the display
SET UP menu
DMX Address
DMX Mode
Run Mode
Direction Rev
Master Slave
Screen Saver
Factory Setting
Language
Function
DMX address setting. Can be changed using either the touch screen or buttons 14/15 above
Unit only operates in 21 Channel DMX Mode (see control table below)
DMX512
Unit operates in DMX mode
Auto Pr 1
Built in Show 1
Auto Pr 2
Built in Show 2
Auto Pr 3
Built in Show 3
Edit Pr
User editable auto program. Scenes can be created in Edit mode.
Sound Pr
Sound to light mode. Sound sensitivity can be adjusted in Advanced settings.
X Reversion
Y Reversion
Off / On - reverses rotational settings
XY Swap
Master
Unit operates in Master mode
Slave
Unit operates in Slave mode
Turns Screen saver on or off. When switched to off, display will turn black during periods of inactivity.
Enters ‘factory setting’ mode (not required for normal usage)
Changes language used on the display screen
Edit menu
The Edit menu is for creating your own light shows from scratch and also control each Lamp individually.
EDIT menu
Scenes Edit
Function
Edit programs 1-6
Edit Scenes 1-12
X Pos:
Y Pos:
XY Speed:
Open Run:
LightAuto:
Lamp 1:
Lamp 2:
Lamp 3:
Lamp 4:
Lamp 5:
Lamp 6:
Lamp 7:
Lamp 8:
Lamp 9:
Lamp 10:
Lamp 11:
Lamp 12:
Delay Time:
0-255
0-255
0-255
0-127 (Direction 1) 128-255 (Direction 2)
0-255 (pattern selection)
0-2 (off) 3-255 (pattern selection)
0-255 (pattern selection)
0-255 (pattern selection)
0-255 (pattern selection)
0-255 (pattern selection)
0-255 (pattern selection)
0-255 (pattern selection)
0-255 (pattern selection)
0-255 (pattern selection)
0-255 (pattern selection)
0-255 (pattern selection)
0-255 (pattern selection)
0-255
System menu
Version Info
Shows unit version number
DMX Values
DMX Signal values that the unit is receiving
System Error
Shows a list if any errors the unit may have encountered
Total Time
Shows the total operating time of the unit
The Use Time
Shows the current operating time of the unit
Lamp Reset
Resets the unit
Advanced Menu
X Hall state H
Sensors Inf
If unit is poperating correct, should read
Y Hall state H
X encoder
L
Y encoder
L
Reset adjust
No function
Touch Set
Calibrates the Touch screen
White Adjust
Adjusts the brightness of the RGBY lamps
Sound adjust
Adjusts the units sound sensitivity from 0-255
DMX address setting - When controlling the unit (or units) with a DMX controller, each one must be set with a specific DMX
address. You can choose to set all units with the same DMX address or you can set every unit with its own DMX address. If all
units are set with the same DMX address all units will be synchronised and operate in the same way.
If you set each unit with a different DMX address, they will receive the DMX signal from their own DMX address. You will now be
able to control each unit individually. The DMX address that you set for each unit must be determined by the number of channels.
This unit operates in 21 Channel mode, so you should set the starting address of the first unit to A001, the second unit must then
be set to A022 (1+21), the third to A043 (22+21) e.t.c.
21 Channel DMX control table
CH6
DMX channel
Value
Function
CH1
0-255
X Axis position (Rotating Arm)
CH2
0-255
Y Axis position (Rotating Sphere)
CH3
0-255
X Axis position (Rotating Arm) FINE TUNE
CH4
0-255
Y Axis position (Rotating Sphere) FINE TUNE
CH5
0-255
XY Speed
Y Axis Limitless Rotation
0-9
10-127
128-255
Off
Direction A (Slow/Fast/Slow)
Direction B (Slow/Fast/Slow)
CH7
CH8-CH19
12 Individual LED’s
CH20
Light effect
CH21
Auto mode
0-255
0-2
3-119
120-169
170-219
220-255
0-4
5-255
0-2
3-255
Master dimmer
Off
Colour Macro
4 Colour change
4 Colour (water running effect)
Strobe & colour change
Off
36 Group light effects
Off
Auto mode
Master/Slave operation
Connect the units in a Master/Slave chain via 3 pin DMX cables:
1. Connect the DMX output of the Master unit to the DMX input of the first Slave unit.
2. Next connect another DMX cable from the first Slave unit DMX output to the second Slave unit DMX input.
3. Continue in this fashion until all units are connected.
4. Set the Master Slave option to Master on the first unit, and Slave on the second unit
5. Slave unit will now follow the operation of the Master unit.
Product specification
Mains power / rated power
Control modes
Display
Light source
Beam angle
Operating temperature
DMX512 connections
Dimensions (WxDxH)
Nett weight
AC100~240V, 50/60Hz / 300W
21 Channel DMX512 / Auto / Sound-to-Light / Master/Slave
Colour touch screen LCD control panel
12 x 20W high power 4 in 1 LED’s
12°
0°C to 40°C
3 pins XLR male/female
320x230x400mm
7.0kg
Due to continuous product development, specifications and appearance are subject to change.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising