Mig C160i
GB
Caddy
Mig C160i
Instruction manual
0440 000 001GB 20120110
Valid for serial no. 924-xxx-xxxx
-2-
1 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1
4
6
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
3 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
8
4.1
4.2
4.3
Lifting instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mains power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
8
9
5 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
5.1 Connection and control devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3 Polarity change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4 Wire feed pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.5 Replacing and inserting wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.5.1
Changing the feed roller groove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.6 Shielding gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.7 Overheating protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
11
11
12
13
13
13
13
6 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
6.1
6.2
Inspection and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the wire liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
14
7 FAULT TRACING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 ORDERING OF SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDER NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WEAR PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
15
16
17
18
19
Rights reserved to alter specifications without notice.
TOCe
-3-
GB
1
SAFETY
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or
near the equipment observes all the relevant safety precautions. Safety precautions must meet the
requirements that apply to this type of equipment. The following recommendations should be ob­
served in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the equip­
ment. Incorrect operation of the equipment may lead to hazardous situations which can result in in­
jury to the operator and damage to the equipment.
1.
Anyone who uses the equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding and cutting
2.
The operator must ensure that:
S no unauthorised person is stationed within the working area of the equipment when it is
started up.
S no-one is unprotected when the arc is struck
3.
The workplace must:
S be suitable for the purpose
S be free from drafts
4.
Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame-proof
clothing, safety gloves.
S Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5.
General precautions
S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during operation.
-4bc21e
© ESAB AB 2011
GB
WARNING
Arc welding and cutting can be injurious to yourself and others. Take precautions when welding and
cutting. Ask for your employer's safety practices which should be based on manufacturers' hazard
data.
ELECTRIC SHOCK - Can kill
S
Install and earth the unit in accordance with applicable standards.
S
Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S
Insulate yourself from earth and the workpiece.
S
Ensure your working stance is safe.
FUMES AND GASES - Can be dangerous to health
S
Keep your head out of the fumes.
S
Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS - Can injure eyes and burn skin.
S
Protect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S
Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S
Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE - Excessive noise can damage hearing
S
Protect your ears. Use earmuffs or other hearing protection.
S
Warn bystanders of the risk.
MALFUNCTION - Call for expert assistance in the event of malfunction.
Read and understand the instruction manual before installing or operating.
PROTECT YOURSELF AND OTHERS!
WARNING
Do not use the power source for thawing frozen pipes.
CAUTION
This product is solely intended for arc welding.
CAUTION
Class A equipment is not intended for use in residential locations where
the electrical power is provided by the public low-voltage supply system.
There may be potential difficulties in ensuring electromagnetic
compatibility of class A equipment in those locations, due to conducted
as well as radiated disturbances.
CAUTION
Read and understand the instruction manual before
installing or operating.
-5bc21e
© ESAB AB 2011
GB
Dispose of electronic equipment at the recycling facility!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical and/or
electronic equipment that has reached the end of its life must be disposed of at a
recycling facility.
As the person responsible for the equipment, it is your responsibility to obtain
information on approved collection stations.
For further information contact the nearest ESAB dealer.
ESAB can provide you with all necessary welding protection and accessories.
2
INTRODUCTION
ESAB's accessories for the product can be found on page 19.
Mig C160i is a portable welding power source in a compact design, intended for
MIG/MAG welding.
It is possible to switch between welding with solid wire/shielding gas and welding
with selfshielded cored wire without gas.
The power source operates with wire diameters from ∅0.6 to ∅1.0 mm. Pure argon,
mixed gas or pure CO2 may be used as shielding gases.
ESAB's accessories for the product can be found on page 19.
2.1
Equipment
The power source is supplied with:
S
S
S
S
S
S
Instruction manual
Welding gun MXL 180 (3m, fixed)
Return cable with clamp (3m, fixed)
Mains cable (3m, fixed, with plug)
Shoulder strap (see page 8)
Gas hose with quick connection (4.5m)
-6bc21e
© ESAB AB 2011
GB
3
TECHNICAL DATA
Power source
Mig C160i
Mains voltage
230 V, 1∼ 50/60 Hz
Permissible load at
35 % duty cycle
60 % duty cycle
100 % duty cycle
150 A / 21.5 V
120 A / 20 V
100 A / 19 V
Setting range
30A / 15.5 V-160A / 22 V
Open circuit voltage
60 V
Open circuit power
15 W
Efficiency at maximum current
82%
Power factor at maximum current
0.99
Wire feed speed
2.0 - 11.0 m/min
Wire diameter
Fe
Cored wire
0.8 (0.6-1.0)
0.8-1.0
Max. diameter wire bobbin
∅ 200 mm
Continual sound pressure at no-load
< 70 dB
Dimensions lxwxh
449 x 198 x 347 mm
Weight
12 kg
Operating temperature
-10 to +40oC
Transportation temperature
-20 to +55° C
Enclosure class
IP 23C
Application classification
Welding torch
MXL 180
Cooling
Air/shielding gas
Permitted load at 20 % duty cycle
Carbon dioxideCO2
Mixed gas Ar/CO2
Self-shielded
200 A
180 A
120 A
Permitted load at 35 % duty cycle
Carbon dioxide CO2
Mixed gas Ar/CO2
Self-shielded
180 A
150 A
100 A
Recommended gas flow
8–15 l/min
Wire diameter
0.6 - 1.0 mm
Weight
1.32 kg
Length cable assembly
3.0 m
Standard control cable
2- pole
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or cut at
a certain load without overloading. The duty cycle is valid for 40° C.
-7bc21e
© ESAB AB 2011
GB
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23C is designed for indoor and outdoor use.
Application class
The symbol
indicates that the power source is designed for use in areas with increased
electrical hazard.
4
INSTALLATION
The installation must be carried out by a professional.
Note
Mains supply requirements
High power equipment may, due to the primary current drawn from the mains supply, influence the
power quality of the grid. Therefore connection restrictions or requirements regarding the
maximum permissible mains impedance or the required minimum supply capacity at the interface
point to the public grid may apply for some types of equipment (see technical data). In this case it
is the responsibility of the installer or user of the equipment to ensure, by consultation with the
distribution network operator if necessary, that the equipment may be connected.
4.1
Lifting instruction
The power source is lifted by the handle or by the shoulder strap, supplied with the
power source. The strap is fastened as shown in the picture below.
4.2
Location
Position the welding power source in such a way that its cooling air inlets and outlets
are not obstructed.
-8bc21e
© ESAB AB 2011
GB
4.3
Mains power supply
Check that the unit is connected to the correct mains power supply voltage, and that
it is protected by the correct fuse size. A protective earth connection must be made,
in accordance with regulations.
Rating plate with supply connection data
Recommended fuse sizes and minimum cable area
Mig C160i
Mains voltage
230 V ±15% 1∼ 50/60 Hz
Mains cable area
3G1.5 mm2
Phase current, Ieff
10 A
Fuse anti-surge
16 A
NOTE! The mains cable areas and fuse sizes as shown above are in accordance with Swedish
regulations. Use the power source in accordance with the relevant national regulations.
Extension cable
If needed, it is recommended to use an extension cable, 3x2.5 mm2, of a maximum
length of 50m.
Supply from power generators
The power source can be supplied from different types of generators. However,
some generators may not provide sufficient power for welding. The generators with
AVR, equivalent or better type of regulation with rated power 5.5...6.5 kW are
recommended to supply the power source within it's full capacity.
It is also possible to use generators with lower rated power, starting from 3.0kW, but
in that case the setting must be proportionally limited. The power source is protected
against undervoltage. If the power supplied by the generator is not sufficient, the
welding is interrupted. Especially the welding start could be disturbed. In case of
disturbed welding process, either adjust the welding parameters or change to a more
powerful generator.
5
OPERATION
General safety regulations for handling the equipment can be found on
page 4. Read through before you start using the equipment!
NOTE: When moving the equipment use intended handle. Never pull on the gun.
WARNING
Rotating parts can cause injury, take great care.
-9bc21e
© ESAB AB 2011
GB
WARNING
Assure that the side panels are closed during operation.
WARNING
Risk of crushing when replacing the wire bobbin!
Do not use safety gloves when inserting the welding wire between the feed rollers.
WARNING!
Lock the bobbin in order to prevent it from
sliding off the hub.
5.1
Connection and control devices
1
Mains supply switch
6
Knob for setting of material thickness
2
Green indicating lamp, power supply ON
7
Knob for arc correction
3
4
5
Orange indicating lamp, overheating
Welding gun
Return cable
8
9
Connection for shielding gas
Mains cable
- 10 bc21e
© ESAB AB 2011
GB
5.2
Operation
The power source is not powered instantly when the mains switch (1) is turned on.
After approximately 2 seconds the green lamp (2) indicates that the power source is
ready.
If the welding gun trigger is pressed while the power source is being turned on, the
operation is disabled, until the trigger is released. This is also indicated by the
orange lamp (3).
The main knob (6) is scaled in mm and ga. The numbers point out recommended
thicknesses of the mild steel workpiece to be welded with 0.8 mm wire. This knob
simultaneously adjusts both the wire feed speed and the average output voltage.
The knob (7) sets the arc length correction or i.e. the voltage correction.
The return cable (5) must be reliably connected to the workpiece or to the welding
table.
The side panel covering the wire feeder must be closed prior to welding.
The power source is instantly switched with the mains switch (1).
5.3
Polarity change
+/- TERMINALS
The power source is delivered with the welding wire connected to the plus pole.
Some wires, e.g. shelfshielded cored wires, are recommended to be welded with
negative polarity. Negative polarity means that the wire is connected to the minus
pole and the return cable to the plus pole. Check the recommended polarity for the
welding wire you want to use.
- 11 bc21e
© ESAB AB 2011
GB
The polarity can be changed as follows:
1. Switch off the power source and disconnect the mains cable.
2. Open the side panel.
3. Bend the rubber covers back to give access to the +/- terminals.
4. Remove the nuts and washers. Note the correct order of the washers.
5. Change the position of the cables to the desired polarity (see marking).
6. Install the washers in correct order and tighten the nuts to spanner tightness.
7. Make sure the rubber covers are covering the +/- terminals.
5.4
Wire feed pressure
Start by making sure that the wire moves smoothly through the wire guide. Then
set the pressure of the wire feeder's pressure rollers. It is important that the
pressure is not too great.
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
Fig 1
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
Fig 2
To check that the feed pressure is set correctly, you can feed out the wire against
an insulated object, e.g. a piece of wood.
When you hold the gun approx. 5 mm from the piece of wood (fig. 1) the feed
rollers should slip.
If you hold the gun approx. 50 mm from the piece of wood, the wire should be
fed out and bend (fig. 2).
- 12 bc21e
© ESAB AB 2011
GB
5.5
S
S
S
S
S
S
S
Replacing and inserting wire
Open the side panel.
Place the spool on the hub and secure it with the lock.
Disconnect the pressure arm by folding it sidewards, the pressure roller slides
away.
Straighten out the new wire 10-20 cm. File away burrs and sharp edges from the
end of the wire before inserting it into the wire feeder.
Make sure that the wire goes properly into the feed roller groove and into the
outlet nozzle and the wire liner.
Secure the pressure arm.
Close the side panel.
Feed the wire through the welding gun until it comes out through the nozzle. This
operation should be carried out carefully, as the wire is ready for welding and an
unintentional arc may occur. Keep the gun off conducting parts during feeding the
wire through and terminate wire feeding instantly when the wire comes out.
See Technical Data, chapter 3, for suitable wire dimensions for each wire type.
Use only ∅200mm spools. Note! ∅100mm/1kg spools are not applicable.
WARNING!
Do not keep the welding gun near the ears or the face during the wire feeding,
as this may result in personal injury.
5.5.1 Changing the feed roller groove
The power source is delivered with the feed roller set for ∅0.8/1.0mm welding wire. If
you want to use it for ∅0.6mm wire you must change groove in the feed roller.
1. Fold back the pressure arm to release the pressure roller.
2. Switch on the power source and press the gun trigger to position the feed roller
so that the locking screw is visible.
3. Switch off the power source.
4. Use a 2mm Allen key to open the locking screw about half a turn.
5. Pull the feed roller off the shaft and turn it around. See marking on the side of the
feed roller for suitable wire diameters.
6. Put the roller back on the shaft and make sure it goes all the way in. You may
need to turn the roller to position the locking screw over the flat surface of the
shaft.
7. Tighten the locking screw.
5.6
Shielding gas
A mixture of carbon dioxide and argon or pure carbon dioxide can be used as
shielding gases.
5.7
Overheating protection
Overheating is indicated by lamp (3). A thermal overload fuse protects the unit against
overheating by disabling the welding if overheating occurs. The fuse resets automati­
cally when the unit has cooled.
- 13 bc21e
© ESAB AB 2011
GB
6
MAINTENANCE
Regular maintenance is important for safe, reliable operation.
CAUTION
All guarantee undertakings from the supplier cease to apply if the customer attempts any
work to rectify any faults in the product during the guarantee period.
6.1
Inspection and cleaning
Power source
S
S
S
Check regularly that the power source is free from dirt.
How often and which cleaning methods apply depend on: the welding process,
arc times, placement, and the surrounding environment. It is normally sufficient
to blow the dust out of the power source with dry compressed air (reduced
pressure) once a year.
Clogged or blocked air inlets and outlets otherwise result in overheating.
Welding gun
S
6.2
The welding gun's wear parts should be cleaned and replaced at regular
intervals in order to achieve trouble-free wire feed. Blow the wire guide clean
regularly and clean the contact tip.
Changing the wire liner
A. Loosen the fixing screw and take the roller off the axle.
B. Loosen the adaptor nut, straighten the gun cable and remove the liner.
C. Insert the replacement liner into the straightened cable until it touches the contact
tip.
D. Lock the liner with adaptor nut. Cut excess of liner so it sticks 7mm out of the tip
adaptor.
- 14 bc21e
© ESAB AB 2011
GB
7
FAULT TRACING
Try these recommended checks and inspections before sending for an authorised
service technican.
Type of fault
No arc
Welding current is interrupted
during welding
The overheating protection
trips frequently
Poor welding performance
8
Actions
S
Check that the mains power supply switch is turned on.
S
Check that the welding current supply and return cables are
correctly connected.
S
Check that correct current value is set.
S
Check whether the overheating protection has tripped.
(indicated by the orange lamp on the front).
S
Check the main power supply fuses.
S
Check to see whether the air inlet or outlet are clogged.
S
Make sure that you are not exceeding the rated data for the
power source (i.e. that the unit is not being overloaded).
S
Check that the welding current supply and return cables are
correctly connected.
S
Check that the correct current value is set.
S
Check that the correct welding wires are being used.
S
Check the main power supply fuses.
S
Check if proper rollers are applied and if the pressure of the
wire feeder's pressure rollers is properly set.
ORDERING OF SPARE PARTS
Repair and electrical work should be performed by an authorised ESAB service
technician. Use only ESAB original spare and wear parts.
Mig C160i is designed and tested in accordance with the international and European
standards 60974-1, 60974-5 and 60974-10. It is the obligation of the service unit which
has carried out the service or repair work to make sure that the product still conforms
to the said standard.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.
- 15 bc21e
© ESAB AB 2011
Diagram
- 16 bc21e
© ESAB AB 2011
Mig C160i
Order number
Ordering no.
Denomination
0349 310 850 Welding power source
Type
Notes
Caddy® Mig C160i, CE (Europe) 230 V, 1∼ 50/60 Hz
0349 300 556 Spare parts list
- 17 bc21o
© ESAB AB 2011
Mig C160i
Wear parts
Item
Denomination
Ordering no.
Gas nozzle
Gas nozzle/Tip insulator MXL
0700 200 054
0700 200 105
B
Contact tip
0700 200 063
0700 200 064
0700 200 065
0700 200 066
C
Nozzle spring
0700 200 078
D
Tip adaptor
0700 200 072
Wire liner
0700 200 085
0700 200 087
0700 200 091
A
E
Notes
W 0.6 M6x25
W 0.8 M6x25
W 0.9 M6x25
W 1.0 M6x25
W 0.6-0.8 Steel for Fe and Ss wire
W 0.9-1.2 Steel for Fe and Ss wire
W 0.9-1.2 PTFE for Al and CuSi wire
O-ring 3.5/IDX 1.8 (3.5x1.8mm)
Black nitrile rubber
O-ring
F
Feed roller
0349 311 890
G
Pressure roller
0349 312 062
H
Inlet nozzle
0455 049 002
W 0.6/0.8-1.0 V-groove
W 0.6-1.0
The feed rollers are marked with wire dimension in mm and inch.
- 18 bc21w
© ESAB AB 2011
Mig C160i
Accessories
Trolley with gas shelf . . . . . . . . . . . . . . . . . . . . . 0459 366 887
(incl. fixing kit for machine)
- 19 bc21a
© ESAB AB 2011
ESAB subsidiaries and representative offices
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna-Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Brussels
Tel: +32 2 745 11 00
Fax: +32 2 745 11 28
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
BULGARIA
ESAB Kft Representative Office
Sofia
Tel/Fax: +359 2 974 42 88
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Vamberk
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
ROMANIA
ESAB Romania Trading SRL
Bucharest
Tel: +40 316 900 600
Fax: +40 316 900 601
DENMARK
Aktieselskabet ESAB
Herlev
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
RUSSIA
LLC ESAB
Moscow
Tel: +7 (495) 663 20 08
Fax: +7 (495) 663 20 09
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
SPAIN
ESAB Ibérica S.A.
Alcalá de Henares (MADRID)
Tel: +34 91 878 3600
Fax: +34 91 802 3461
GERMANY
ESAB GmbH
Solingen
Tel: +49 212 298 0
Fax: +49 212 298 218
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
ESAB international AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
SWITZERLAND
ESAB AG
Dietikon
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
UKRAINE
ESAB Ukraine LLC
Kiev
Tel: +38 (044) 501 23 24
Fax: +38 (044) 575 21 88
ITALY
ESAB Saldatura S.p.A.
Bareggio (Mi)
Tel: +39 02 97 96 8.1
Fax: +39 02 97 96 87 01
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
BRAZIL
ESAB S.A.
Contagem-MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 02 20
Fax: +1 905 670 48 79
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
USA
ESAB Welding & Cutting Products
Florence, SC
Tel: +1 843 669 44 11
Fax: +1 843 664 57 48
Asia/Pacific
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
Africa
EGYPT
ESAB Egypt
Dokki-Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
SOUTH AFRICA
ESAB Africa Welding & Cutting Ltd
Durbanvill 7570 - Cape Town
Tel: +27 (0)21 975 8924
Distributors
For addresses and phone
numbers to our distributors in
other countries, please visit our
home page
www.esab.com
AUSTRALIA
ESAB South Pacific
Archerfield BC QLD 4108
Tel: +61 1300 372 228
Fax: +61 7 3711 2328
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 2326 3000
Fax: +86 21 6566 6622
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
JAPAN
ESAB Japan
Tokyo
Tel: +81 45 670 7073
Fax: +81 45 670 7001
MALAYSIA
ESAB (Malaysia) Snd Bhd
USJ
Tel: +603 8023 7835
Fax: +603 8023 0225
SINGAPORE
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
THE NETHERLANDS
ESAB Nederland B.V.
Amersfoort
Tel: +31 33 422 35 55
Fax: +31 33 422 35 44
www.esab.com
© ESAB AB
110915
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising