SCD 5850MP3
DEUTSCH
ENGLISH
FRANÇAIS
NEDERLANDS
ESPAÑOL
SCD 5850MP3
ENVIRONMENTAL PROTECTION
Do not dispose of this product with the normal household waste at the end
of its life cycle. Return it to a collection point for the recycling of electrical
and electronic devices. This is indicated by the symbol on the product,
user manual or packaging.
The materials are reusable according to their markings. By reusing, recycling or
other forms of utilization of old devices you make an important contribution to
the protection of our environment.
Please contact your local authorities for details about collection points.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1
CAUTION - INVISIBLE LASER RADIATION WHEN OPENING
THE COVER OR PRESSING THE SAFETY INTERLOCK. AVOID
EXPOSURE TO THE LASER BEAM.
This symbol indicates the presence of dangerous
voltage inside the enclosure, sufficient enough to
cause electric shock.
WARNING
Risk of electric shock
Do not open!
Caution: To reduce the risk of electric shock, do not remove the cover (or back). There
are no user serviceable parts inside. Refer servicing to qualified service personnel.
This symbol indicates the presence of important
operating and maintenance instructions for the
device.
Safety, Environmental and Setup Instructions
•
Use the device in dry indoor environments only.
•
Protect the device from humidity.
•
Do not open the device. RISK OF ELECTRIC SHOCK! Refer opening and servicing to qualified personnel.
•
Connect this device to a properly installed and earthed wall outlet only. Make sure the mains voltage corresponds with
the specifications on the rating plate.
•
Make sure the mains cable stays dry during operation. Do not pinch or damage the mains cable in any way.
•
A damaged mains cable or plug must immediately be replaced by an authorized service center.
•
In case of lightning, immediately disconnect the device from the mains supply.
•
Children should be supervised by parents when using the device.
•
Clean the device with a dry cloth only.
Do NOT use CLEANING AGENTS or ABRASIVE CLOTHS!
•
Do not expose the device to direct sunlight or other heat sources.
•
Install the device at a location with sufficient ventilation in order to prevent heat accumulation.
•
Do not cover the ventilation openings!
•
Install the device at a safe and vibration-free location.
•
Install the device as far away as possible from computers and microwave units; otherwise radio reception may be
disturbed.
•
Do not open or repair the enclosure. It is not safe to do so and will void your warranty. Repairs only by authorized
service/ customer center.
•
The device is equipped with a “Class 1 Laser”. Avoid exposure to the laser beam as this could cause eye injuries.
•
Only use mercury and cadmium-free batteries.
•
Used batteries are hazardous waste and NOT to be disposed of with the household waste!!! Return the batteries to your
dealer or to collection points in your community.
•
Keep batteries away from children. Children might swallow batteries. Contact a physician immediately if a battery was
swallowed.
•
Check your batteries regularly to avoid battery leakage.
Used batteries are hazardous waste and NOT to be disposed
of with the household waste! As a consumer you are legally
obligated to return all batteries for environmentally responsible
recycling – no matter whether or not the batteries contain harmful
substances*).
Return batteries free of charge to public collection points in your
community or to shops selling batteries of the respective kind.
Only return fully discharged batteries.
*) marked Cd = cadmium, Hg = mercury, Pb = lead
1. FUNCTION SWITCH
CD/TAPE (OFF)/RADIO
16. AC SOCKET
2. BAND SWITCH
18. FM STEREO LED INDICATOR
3. FM ANTENNA
19. CASSETTE COMPARTMENT
4. CD DOOR
20. NO FUNCTION
5. TUNING KNOB
21. CASSETTE PLAY BUTTON
6. BASS BOOST BUTTON
22. CASSETTE REWIND BUTTON
7. CD SKIP/SEARCH FORWARD
BUTTON 23. CASSETTE FAST FORWARD
BUTTON
8. CD SKIP/SEARCH BACKWARD
BUTTON 24. CASSETTE STOP/EJECT BUTTON
9. CD PROGRAM BUTTON
10. CD MODE BUTTON
11. CD STOP BUTTON
12. CD PLAY/PAUSE BUTTON
13. LCD DISPLAY
14. STEREO HEADPHONE JACK
17. BATTERY DOOR
25. CASSETTE PAUSE BUTTON
26. SPEAKER LEFT
27. SPEAKER RIGHT
28. DIAL POINTER
29. FOLDER UP BUTTON
30. FOLDER DOWN BUTTON
15. VOLUME CONTROL KNOB
English - 1
AC OPERATION
Before operation please ensure voltage on the set corresponds to voltage of
your local area. Unravel AC line cord; insert one end into AC socket on the
set while the other end into a standard AC outlet.
Remarks:
In case of malfunction due to electrostatic discharge (ESD), reset the unit by
reconnecting AC cord again to resume to normal operation.
When not in use – Unplug AC power cord completely from AC power socket.
Warning:
The power cable/disconnect device shall remain easy to operate/disconnect.
When you are not going to use the unit for a long period of time, disconnect
the AC power cord. Where the mains plug or an appliance coupler is used as
disconnecting device, the disconnecting device shall remain operable.
BATTERY OPERATION
Disconnect AC cord set completely. Open the BATTERY DOOR and insert UM2/ “C” size x 8 batteries (not supplied) making sure the indicated battery
polarity is observed.
When not in use – Remove all batteries if the unit will not be used for few
months or more.
RADIO OPERATION
1. Slide FUNCTION SWITCH to “RADIO” position.
2. Slide BAND SWITCH to the desired waveband.
3. Turn the TUNING KNOB to your desired radio station.
4. Adjust sound level by rotating VOLUME CONTROL KNOB.
5. To turn off radio, simply slide FUNCTION SWITCH to “TAPE (OFF)” position.
FM stereo indicator
When tuned to FM Stereo broadcast “FM ST. LED INDICATOR” will light up.
In some weak signal areas, FM Stereo signal may not be strong enough and
can cause excessive background noise. In this case, slide the BAND SWITCH
to “FM” position.
Antennas
For best reception, fully extend FM ANTENNA to receive FM stations.
For AM reception, the unit has a built-in antenna, turn the whole unit for best
reception.
English - 2
Play/Pause mode
1. When PLAY/PAUSE BUTTON is pressed during CD
stop mode, the first track will be played. The Play
indicator “” and specific number of track is being
played will be shown on LCD DISPLAY
.
2. For interruption while CD is playing, press CD
PLAY/PAUSE BUTTON once. The Play indicator “”
will blink continuously on LCD DISPLAY.
3. Though the sound stops, disc will continue to spin.
To resume playback, press CD PLAY/PAUSE BUTTON once again. Music
will start from the exact position where it was interrupted.
4. To stop CD playback, press CD STOP BUTTON once whether CD is in Play
or Pause mode; LCD DISPLAY will show the total number of tracks in the
disc again.
5. To turn off the unit, slide FUNCTION SWITCH to “TAPE (OFF)” position.
Skip and Search mode
1. During play or pause mode, when CD SKIP/SEARCH FORWARD or
BACKWARD BUTTON is pressed once, it will go to next track or go
back to the beginning of the track respectively.
2. During play mode, when CD SKIP/SEARCH FORWARD or BACKWARD
BUTTON is pressed and held, it will search the track with audible
high-speed forward or backward playback.
Repeat mode
1. Repeat 1:
When MODE BUTTON is pressed once, Repeat
” will be shown on LCD DISPLAY.
indicator “
This single track of music will be repeated.
2. Repeat All:
When MODE BUTTON is pressed twice, Repeat All
” will be shown on LCD DISPLAY.
indicator “
The whole disc can be played continuously.
3. To cancel repeat function
Press MODE BUTTON repeatedly until Repeat
indicator disappears from LCD DISPLAY.
English - 5
Random play mode
This feature allows tracks on the disc to be played in random order.
1. During CD stop mode, press MODE BUTTON three times. The “
indicator will be shown on LCD DISPLAY and play
automatically.
2. To cancel random play function, press MODE
BUTTON again. The “
” indicator will
disappear from LCD DISPLAY.
”
Program mode
1. During CD stop mode, press PROGRAM BUTTON once. The “PROGRAM”
indicator and number of Program to be memorized starts from the first
” will light up and blink continuously.
program “
Press CD SKIP/SEARCH FORWARD or
BACKWARD BUTTON to your desired musical
track, LCD DISPLAY will show the appropriate track
number. Press PROGRAM BUTTON to store this
track in memory.
2. Repeat above procedure until all desired tracks have been programmed.
A total of 20 tracks can be stored in memory.
Remarks:
Whenever CD SKIP/SEARCH FORWARD or
BACKWARD BUTTON is pressed, it will always
show the last programmed track first to recall your
memory.
” and
After complete programming, LCD DISPLAY will show “
flash continuously.
3. Press CD PLAY/PAUSE BUTTON once to start
program playback and CD Play indicator “” will
light up.
4. To check the program you have stored after
complete programming, press PROGRAM BUTTON once during CD stop
mode; then press CD SKIP/SEARCH FORWARD BUTTON once, LCD
DISPLAY will show the first programmed track number. Repeat above
procedure to read all programmed memory.
5. To cancel programmed memory:
¾ During CD stop mode, press CD STOP BUTTON once.
or
¾ Open CD DOOR during CD stop mode.
The “PROGRAM” indicator will disappear from LCD DISPLAY.
English - 6
PLAYING MP3 DISC
Getting started
Note:
Should skipping of tracks occur during MP3 disc playing, try reduce
the volume.
When MP3 disc is playing, do not open CD DOOR.
1. Pull up CD DOOR. Put a MP3 disc into CD compartment and close the
door. Set FUNCTION SWITCH to “CD” position.
Note: Ensure CD DOOR is closed properly and locked in place.
2. When CD DOOR is closed with a MP3 disc inside,
total track number in the disc will be shown on LCD
DISPLAY and go to stop mode.
3. If there is no disc inside, LCD DISPLAY will show
” and go to stop mode.
“
4. If CD DOOR is not closed, LCD DISPLAY will show
“
”.
Play/Pause mode
1. When PLAY/PAUSE BUTTON is pressed during CD stop mode, the first
track will be played. The Play indicator “” and
” indicator will be shown to indicate MP3 disc
“
is being played. LCD DISPLAY will show specific
track number is being played.
2. To select specific musical track inside the MP3 disc.
MP3 music can be stored into CD disc with or without folder according to
your “MP3 burning method”.
a. If MP3 disc is
downloaded without
dividing into folder, all
track number will be
shown directly in LCD
DISPLAY. The Album
number will only show
after pressing FOLDER UP or DOWN BUTTON.
b. If music is stored into different folders, you’ve to select specific Album
number first by pressing FOLDER UP or DOWN BUTTON; afterwards
press CD SKIP/SEARCH FORWARD or BACKWARD BUTTON to
select specific track number of music inside this Album.
English - 7
Example: To select Album # 4, track # 3
Step – 1:
Press FOLDER UP or DOWN
BUTTON to select Album # 4.
Step – 2:
Press CD SKIP/SEARCH
FORWARD or BACKWARD BUTTON to select Track # 3 inside
this Album # 4
3. For interruption while MP3 disc is playing press CD
PLAY/PAUSE BUTTON once. The Play indicator “” will blink continuously
on LCD DISPLAY.
4. Though the sound stops, disc will continue to spin. To resume playback,
press CD PLAY/PAUSE BUTTON once again. Music will start from the
exact position where it was interrupted.
5. To stop MP3 disc, press CD STOP BUTTON once whether MP3 disc is in
Play or Pause mode.
6. To turn off the unit, slide FUNCTION SWITCH to “TAPE (OFF)” position.
Repeat mode
1. Repeat 1:
When MODE BUTTON is pressed once, Repeat
indicator “
” will light. This single track of music
will be repeated.
2. Repeat Folder:
When MODE BUTTON is pressed twice,
“
” and “
” indicators will be shown.
This specific folder will be played repeatedly.
Remarks:
The folder and track number will be shown every 2 seconds alternatively.
3. Repeat All:
When REPEAT BUTTON is pressed three times,
” will be shown.
Repeat All indicator “
The whole disc can be played continuously.
4. To cancel repeat function
Press MODE BUTTON repeatedly until Repeat
indicator disappears from LCD DISPLAY.
English - 8
Random play mode
This feature allows tracks on the disc to be played in random order.
1. During CD stop mode, press MODE BUTTON four
times, “
” indicator will be shown on LCD
DISPLAY. Press PLAY/PAUSE BUTTON once to start
the playback.
2. To cancel Random play function, press MODE
BUTTON again, “
” indicator will disappear from LCD DISPLAY.
Program mode
1. During CD stop mode, press PROGRAM BUTTON once. The “PROGRAM”
indicator and number of Program to be memorized
starting from the first program “
” will light up
and blink continuously. Press FOLDER UP or DOWN
BUTTON, then press CD SKIP/SEARCH FORWARD
or BACKWARD BUTTON to select your desired
musical track. LCD DISPLAY will show track number of this specific Album
to be programmed. Press PROGRAM BUTTON to store this track in
memory.
2. Repeat above procedure until all desired tracks have been programmed.
Remarks:
Whenever FOLDER UP or DOWN BUTTON is pressed, it will always show
the last programmed Album number first to recall your memory.
A total of 20 tracks can be stored in memory. After complete
” and blink
programming, LCD DISPLAY will show “PROGRAM
continuously.
3. To start Programmed playback, press CD PLAY/PAUSE BUTTON once.
CD Play indicator “”, “PROGRAM” and track number of the specific
Album will light up.
Example: Album # 3, Track # 2.
4. To check the program you have stored after complete programming,
press PROGRAM BUTTON once during CD stop mode. LCD DISPLAY will
” and blink continuously. Press FOLDER UP or DOWN
show “
English - 9
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement