Ilnstallat! - Sears Parts Direct

Ilnstallat! - Sears Parts Direct
Built-In Wall Oven
27" (68.6 cm) models
JKS10, JKP30, JKP35, JKP55, JKP70, JKP75,
PK916, PK956, ZEK938, ZEK958
Ilnstallat!on
nstruct=ons
30" (76.2 cm) models
JTP30, JTP35, JTP55, JTP70, JTP75, PT916,
PT920, PT956, PT960, ZET938, ZET958
If you have questions, call 1.800.GE.CARES
ge.com
Before You Begin
Read these instructions carefully and completely.
• IMPORTANT-save
instructions
these
for local inspector's
• IMPORTANT-observe
use.
all
governing
codes and ordinances.
• Note to Installer--Be
sure to leave these
instructions
with the consumer.
or visit our website at:
• Proper installation is the responsibility
of the installer and product failure due
to improper installation is NOT covered
under warranty.
• NOTE--This
grounded.
appliance
must be properly
• ATTENTION INSTALLER
• Note to Consumer--Keep
these
instructions for future reference.
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT permitted
on these products.
Parts Included
Materials Needed
(Appearance
will vary)
Wire Nuts
Screws For Installation
(8-18 x .750 flat head
Phillips wood screws)
27" (68.6 cm)
Metal Bottom Trim
Strain Relief Clamp
for 1/2" conduit
Junction
Box
36" (91 cm)
of String
Tools Needed
(68.6 cm)
Metal Bottom
Trim Assembly
(on some models or
can be purchased
separately)
31-10647
02-07 JR
30" (76.2 cm)
Metal Bottom Trim
Assembly
1/8" (3 mm) Drill Bit and
Electric or Hand Drill
Phillips
Screwdriver
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
For Your Safety
Electrical
• Be sure your oven is installed properly by
a qualified installer or service technician.
Requirements
• Be sure the oven is securely installed in a
cabinet that is firmly attached to the house
structure. Weight on the oven door could
cause the oven to tip and result in injury.
Never allow anyone to climb, sit, stand or
hang on the oven door.
• Make sure the cabinets and wall
coverings around the oven can withstand
the temperatures
(up to 200°F [93.3°C])
generated by the oven.
Rating plate is located on oven side trim,
side front frame or lower front frame.
WARNING:
F
Location
<4.1 KW
20 Amp
4.9 KW-7.2 KW
4.3 KW-6.2 KW
30 Amp
7.3 KW-9.6 KW
6.3 KW-8.3 KW
40 Amp
9.7 KW-12.0 KW
8.4 KW-10.4 KW
50 Amp
--
I
Check with your local utilities for electrical codes
which apply in your area. Failure to wire your oven
according to governing codes could result in a
hazardous condition. If there are no local codes,
your oven must be wired and fused to meet the
requirements of the National Electrical Code,
ANSI/NFPA No. 70-Latest Edition. You can
get a copy by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
This appliance must be supplied with the proper
voltage and frequency, and connected to an
individual, properly grounded branch circuit,
protected by a circuit breaker or fuse. See the
rating plate located on the oven frame to determine
the rating of the product. Use the chart below to
determine the minimum recommended dedicated
circuit protection.
<4.8 KW
r'--_
We recommend you have the electrical wiring
and hookup of your oven connected by a qualified
electrician. After installation, have the electrician
show you where your main oven disconnect is
located.
Electrical
Requirements
Recommended
Circuit Size
(Dedicated)
_
I
power to the oven supply line
must be shut off while line
connections are being made. Failure
to do so could result in serious injury
or death.
KW Rating
208V
--
Rating Plate
The electrical
KW Rating
240V
cont.
Effective January 1, 1996, the National
Electrical Code requires that new, but not existing,
construction utilize a four-conductor connection to
an electric oven. When installing an electric oven
in new construction, a mobile home, recreational
vehicle or an area where local codes prohibit
grounding through the neutral conductor,
follow the instructions in the section on NEW
CONSTRUCTION AND FOUR-CONDUCTOR
BRANCH CIRCUIT CONNECTION.
You must use a three-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz electrical
system. If you connect to aluminum wiring,
properly installed connectors approved for
use with aluminum wiring must be used.
2
Installation Instructions
Pre-lnstallation Checklist
Door removal is not a requirement for
installation of the product, but is an
added convenience. To remove the door:
ALL INSTALLATION
INFORMATION
ON THE FOLLOWING PAGES IS TO
BE USED FOR SINGLEAND
DOUBLE
OVEN INSTALLATION!
Open the oven door as far as it will go.
i
Remove packaging materials.
Check behind hinges and under
false bottom. Remove labels on the
outside of the door, plastic on trims
and panel, all tape around the oven,
and any shipping screws securing
the oven to the base pad.
F
Push both hinge
_._L.
Hinge
Unlocked
locks down toward
_l_'.!_b. Position
the door frame,
Hinge"':':':_
to the unlocked
s_ot __.d
position. This may
require a flat blade
Hinge
screwdriver.
Arm
DO NOT LIFT THE DOOR
BY THE HANDLE!
o_
Place hands on both sides of
the door, and close the oven
door to the removal position,
which is most of the way closed.
"T_-_
II_ji_:_
I_/
I_//
Oven Racks
[_
_
iterature
Pack
Open oven door and remove literature
pack and oven racks.
ift door
up and
out
until the
hinge arms
clear the slots.
Hinge Clears Slot
NOTE: The oven door is very heavy. Be sure
you have a firm grip before lifting the oven
door off the hinges. Use caution once the
door is removed. Do not lay the door on its
handle. This could cause dents or scratches.
Remove Installation Instructions from
literature pack and read them carefully
before you begin.
Be sure to place all literature, Owner's
Manual, Installations, etc. in a safe place
for future reference.
Place the oven on a table or platform
even with the cutout opening. (Platform
must support 150 Ibs. [68 Kg] single,
275 Ibs. [124 Kg] double.)
Remove the bottom trim from the top
of the oven. It will be installed at the end
of the installation process. The trim is
wrapped separately and taped to
the top of the unit.
3
Installation Instructions
Cutout for 27"(68.6cm)Single
Ovens only
Built-In
For JKS10, JKP30, JKP70, PK916, ZEK938 models only.
Cabinet
5" (12.7 cm)
Max. from the
left or right
Cabinet
--Width
_ side
l
Cutout
Allow 1" (2.5 cm)
for overlap of
oven over side
edges of cutout
Cutout Width
25" (63.5 cm)
Min.
Cutout Width
_"
Max.
20" (50.8 cm)
_joJ-"
j--
7-
of 20" (50.8 cm) for
clearance to adjacent
corners, drawers, walls,
etc. when door is open
Cutout
Height
22" (55.9 cm)
27 5/8"
Min. above
(70.2 cm) Min. base rail
28 1/8"
runners
level
with bottom
of cutout
Allow a minimum
23 1/2"
(59.7 cm) Min.
25" (63.5 cm) Min.
25 1/4" (64.1 cm) Max.
lOcm)
__. ___
32 1/2" (82.6 cm)
Cutout
or
-..
Depth
25 114" (64.1
2"x4"
(5crux
27" (68.6 cm)
Recommended
Cutout Location
from Floor
Junction Box
Location
_
"
Width
-.. Allow .......
1 3/8" (3.5 cm)
minimum for
overlap of
oven top and
bottom
of cutou_"-_
Recommended
cutout location
from floor 32 1/2"
Height
27 5/8" (70.2 cm) Min.
28 1/8" (71.4 cm) Max.
Alternate Junction
Box Location access from
adjacent cabinet
may be required
NOTE: If the cabinet does not
have a front frame and the sides
are less than 3/4" (1.9 cm) thick,
shim both sides equally to
establish the cutout width.
(82.6 cm)
2"x4"(5cmx
10cm)
or
equivalent
runners level
with bottom of cutout
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For
single ovens, the runners and braces
must support 150 Ibs (68 Kg).
T
f
24"
(61 cm)
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
1
I_-
18" (45.7 cm)
--i
27" (68.6 cm) "_
These ovens are not approved for
stackable installations.
4
Installation Instructions
Cutoutfor 27"(68.6
Ovensonly
DoubleBuilt-In
For JKP35, JKP55, JKP75, PK956, ZEK958 models only.
6"
(12.7 cm)
Max. from
the left or
Cabinet
right
(68.6
cm)
Cutout
Allow 1" (2.6 cm)
for overlap of
over over side
i
Junction Box
_F._
(63.5 cm) Men.
25 1/4" i
(64.1 cm) Ma_.
Cabinet Width
27" (68.6 cm)
Recommended
Cutout Location
from Floor
13 1/4" (33.7 cm)
Cutout Depth
23 5/8" (60 cm) Men.
Cutout Width
25" (63.5 cm) Men.
Location
iii zzI
25 1/4" (64.1 cm) Max.
edges of
(111.6 cm)
Cutout Height
Min,
iCut°ut
Above
iHeight
base rail
i49 11/t6"
i(126.2 cm) Men.
160 118"
i(127.3 cm) Max.
2" x 4"
(Scmx10cm)
or equivalent
runners
50 1/8" (127.3 cm) Max.
NOTE: If the cabinet does
not have a front frame and
the sides are less than 3/4"
(1.9 cm) thick, shim both
sides equally to establish
the cutout width.
20"(60.6
................
/
Allow a minimum
of 20" (50.8 cm)
for clearance to
adjacent corners,
drawers, walls, etc.
when door is open
Allow jj 1 3/8"
j
(3.6 cm) for
overlap of oven
top and bottom_
49 11/16" (126.2 cm) Men.
Recommended
cutout location
from floor 13 1/4"
(33.7 cm)
of cutout
If the cabinet does not have a solid bottom,
two braces or runners must be installed to
support the weight of the oven. For double
ovens, the runners and braces must
support 300 Ibs (135 Kg).
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
2" x 4"
(Scmx10cm)
or equivalent
runners
level
with bottom
of cutout
Suitable
Bracing
to Support
-T
5
18"cm)
(45.7
Over Centerline
of Cabinet
_-
Installation Instructions
IAICutout for 27" (68.6cm)Single
Built-In
Ovens only Under Counter
For JKS10, JKP30, JKP70, PK916, ZEK938 models only.
Gas or electric cooktops may
be installed over this oven.
See cooktop installation
instructions for cutout size,
See label on top of oven for
approved cooktop models.
240V / 208V
Junction Box
Location
25" (63.5 cm)
\.
\\
5"
(12.7 cm)
Max. from the
left or right
side
Gas and electrical connections
for gas cooktop must be located
in an adjacent accessible
location to the right.
Top and/or side fillers
may be necessary
if unit is positioned
between existing
cabinets. Be sure
they are attached
securely, since they
will anchor the oven
in the cabinet.
_25" (63.5 cm) Min.
25 1/4" (64.1cm) Max.
27 5/8" (70,2 cm) Min.
28 1/8" (71.4 cm) Max. "'; ""
Allow
"_
1 318"
(3.5 cm)
unit overlap top
bottom of
oven, 1" (2.6 cm)
unit overlap side
edges
22" (55.9 cm) Min.
Above Support
Platform
24" (61cm)
6
36" (91.4 cm)
Typical
Countertop
Height
Cabinetry
Cutout for 27" (68.6cm)Single
or
Double Built-In Ovens only- Over a
Warming Drawer
For JKS10, JKP30, JKP35, JKP55, JKP70, JKP75, PK916, PK956, ZEK938,
ZEK958 models only.
Single 27" (68.6 cm)
Double 27" (68.6 cm)
Oven Over
a Warming Drawer
Oven Over
a Warming Drawer
Anti-Tip Block
Against Rear
•Wall Per
Warming
Drawer
Requirement
Anti-Tip Block Against
Rear Wall Per Warming
Drawer Requirement
3" (7.6 cm)
Min,
3" (7.6 cm)
Min.
NOTE: Install the
oven only with
specific models
listed on the label
located on top of
the oven.
Per
Warming
Drawer
Requirement
Per Warming
Drawer
Req_
1" (2.6 cm) Min. Above Toekick
1" (2,6 cm) Min, Above Toekick or
Adjust to Oven Installation
Height
NOTE: Additional clearances between cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth and
height,
• When installing a Warming Drawer below
a single or double oven, a separate 120V,
60 Hz, properly grounded receptacle must
be installed. Refer to installation instructions
packed with the Warming Drawer for
specific installation requirements.
7
Cabinetry
Cutout for 27" (68.6cm)Single
Ovens
only- Below an Advantium or
Between an Advantium and a
Warming Drawer
For JKS10, JKP30, JKP70, PK916, ZEK938 models only.
Single 27" (68.6 cm) Oven
Below an Advantium
Per Advantium
Requirement
Single 27" (68.6 cm) Oven
Between an Advantium and
a Warming Drawer
Per AdvantiL
Requirement
3" (7.6 cm) Min.
Note: Install the
oven only with
specific models
listed on the label
located on top of
the oven.
NOTE: The middle rail separating the two
openings may need to be larger than the 3"
(7.6 cm) minimum shown. Always refer to the
individual installation instructions packed with
each product for specific requirements.
Combined Advantium
Oven Installation:
3" (7.6 cm) Min.
3" (7.6 cm) Min.
Per Warming
Drawer
Req
NOTE: Additional clearances may be
required. Check to be sure the oven
supports above the Warming Drawer
do not obstruct the required interior depth
and height. The middle rail separating the
openings may need to be larger than the 3"
(7.6 cm) minimum shown. Always refer to
the individual installation instructions packed
with each product for specific requirements.
and Wall
When installed in combination with a
single wall oven, use separate electrical
junction boxes.
. Refer to the Advantium oven installation
instructions for electrical requirements of
that product.
. These connections must be made
Warming Drawer
Combined with Advantium
and Single Oven:
Install a separate 120V, 60Hz, properly
grounded receptacle. See installation
instructions packed with each product
for specific requirements.
by a qualified electrician. All electrical
connections must meet National Electrical
Code or prevailing local codes.
8
Installation Instructions
Cutout for 30"(76.2
Ovens only
Built-In
cm)Single
For JTP30, JTP70, PT916, PT920, ZET938 models only.
Cutout
Width
28 1/2" (72.4 cm)
Min.
_
28 5/8" (72.7 cm).
Max.
Allow 11/16"
(1.75 cm) for
overlap of oven
over side edges
of cutout
----
Between
7 3/4" (19.7 cm)
Max.
Junction Box
Location
(junction box
may be
located in
/
___
IN
cutout
I
Recommended
Cutout Location
from Floor
32 1/2" (82.6 cm)
Cutout Depth
23 1/2" (69.7 cm) Min.
Cutout Width
28 1/2" (72.4 cm) Min.
28 6/8" (72.7 cm) Max.
22" (56.9 cm)
Bin, to
Bottom of
Junction Box
Cutout Height
"!-
- - "
S
Allow a minimum
of 21" {63.3 cm) for
clearance to adjacent
corners, drawers,
walls, etc. when
door is open
30" (76.2 cm)
I i
Inside Walls I [_ Height i
i .
Must Be
I I_ 27 1/4"
At Least
Min.
I tN (69.2 cm)
28 112"
I 1_ 27 5/16"
(69.4 cm) Max.
(72.4 cm)
Wide"
21" (53.3 cm)
cabinet)
adjacent
Cabinet Width
27 1/4" (69.2 cm) Min.
27 6/16" (69.4 cm) Max.
NOTE: If the cabinet does
not have a front frame and the
sides are less than 3/4" (1.9 cm)
thick, shim both sides equally to
establish the cutout width.
Recommended
cutout location
from floor 32 1/2"
top and 1W"
(3,2 cm) overlap
of oven bottom
of cutout_-_,
--
Cabinet
Width
30" (76.2 cm)
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For single
ovens, the runners and braces must
support 150 Ibs (68 Kg).
2" x 4"
(5 cm x 10 cm
or equivalent
runners level
with bottom
of cutout
Suitable
Bracing
to Support
Runners --
-F----- 64 21 5/8.9 cm) Over
Centerline
of Cabinet
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
\
Side by Side Installations
Install two wall ovens in separate cutouts.
Allow 2" (5.1 cm) min. between cutouts (PT920
models) or 6" (15.2 cm) min. between cutouts
(all other models).
Cutout Observe all
These ovens are not approved for
stackable installations.
2" (5.1 cm)
Min. (PT920)
dimensionsl_
and
6" (15.2 cm)
r_lu rements.
Min.
(other models
9
Cutout Observe all
dimensions
and
requirements.
Installation Instructions
IAICutoutfor30' 6.2cm)Double Built-InOvensonly
For JTP35, JTP55, JTP75, PT956, PT960, ZET958 models only.
Cutout
Width
28 112" (72.4 cm)
Min,
28 518" (72.7 cm)
==:
Max.
7 3/4"
(19.7 cm Junction Box
) Location
(junction box
may be
located in
adjacent
cabinet)
I
/
Allow 11/16"
(1.75 cm) for
overlap of oven
over side edges
of cutout
Allow a minimum
of 21" (53.3 cm) for
clearance to adjacent
corners, drawers,
walls, etc, when
door is open
Opening
Between
Inside Walls
Must Be At
Least 28 1/2"
_,llow1" (2.5 cm)
minimum for
overlap of oven
top and 1W"
(3.2 cm) overlap
of oven bottom
of cutout
-1
I
I
I
47" (119.4 cm)
Min.
to Bottom of
Junction Box
51 13/16" (131.6 cm)
Min.
51 15/16" (131.9 cm)
Max
Cabinet Width
30" (76.2 cm)
Recommended
Cutout Location
from Floor
12" (30.5 cm)
Cutout Depth
23 1/2" (59.7 cm) Min.
Cutout Width
28 1/2" (72.4 cm) Min.
28 5/8" (72.7 cm) Max.
Cutout Height
51 13/16" (131.6 cm) Min.
51 15/16" (131.9 cm) Max.
NOTE: If the cabinet does not
have a front frame and the sides
are less than 3/4" (1.9 cm) thick,
shim both sides equally to
establish the cutout width.
21" (53.3 cm)
--
i
Recommended
cutout location
(30.5 cm)
Cabinet
Width
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For
double ovens, the runners and braces
must support 275 Ibs (124 Kg).
Suitable
Bracing
to Support
Runners --_(54,
21 5/8"-------_
9 cm) Over
Centerline
of Cabinet
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
10
\
2" x 4"
(Scm
x 10cm)
or equivalent
runners level
with bottom
of cutout
Installation Instructions
IAICutout for 30" (76.2cm) Single Built-InOvens
only Under Counter
For JTP30, JTP70,
PT916, PT920, ZET938
Gas or electric cooktops may be installed over this oven. See
cooktop installation instructions for cutout size. See label on
top of oven for approved cooktop models.
models only.
240V / 208V
Junction Box
,\
Location (junction
box may be in
adjacent cabinet)
7 3/4"
25" (63.5 cm)
(19.7 cm)
\_
Top and/or side fillers
may be necessary
if unit is positioned
between existing
cabinets. Be sure
they are attached
securely, since they
will anchor the oven
in the cabinet.
,-
_"Max_
- 28 1/2" (72.4 cm) Min.
28 5/8" (72.7 cm) Max.
Allow
Gas and electrical
connections
for 30" (76,2 cm) gas cooktop must
be located in an adjacent accessible
location to the right, For 36" (91.4 cm)
be
madegaS
cooktoP,to
the left,the
connections
may
1"
overlap top
of oven,
11/16" (1.8 cm)
overlap side edges
of cutout and
1 1/4" (3.2 cm)
overlap bottom
of oven.
22" (55.9 cm) Min.
Above Support
Platform
36" (91.4 cm)
Typical
Countertop
Height
24" (61 cm)
4" (10.2 cm)
Typical
Toekick
NOTE: This oven is not approved to be installed under a
solid disk, induction or
downdraft modular cooktop.
=
Side by Side Installations
Cutout Observe all
dimensions
and
and
6"(15,2cm) Min.
requtrements. (othermodels) requirements.
Install two wall ovens in separate cutouts.
Allow 2" (5.1 cm) min. between cutouts
(PT920 models) or 6" (15.2 cm) min.
between cutouts (all other models).
CutoutObserve all
dimensionsl_
11
2" (5.1 cm)
Min, (PT920)
Cabinetry
Cutout for 30"(76.2cm) Single or Double
Built-In Ovens only- Over a
Warming Drawer
For JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960,
ZET938, ZET958 models only.
Double 30" (76.2 cm)
Oven Over a Warming
Drawer
Single 30" (76.2 cm)
Oven Over a Warming
Drawer
Block Against
Rear Wall Per Warming
Drawer Requirement
Anti-Tip Block
Against Rear
Wall Per
Warming
Drawer
Requirement
2" (5.1 cm)
Min.
NOTE: install the
2" (5.1 cm)
Min.
oven only with
specific models
Iisted on the labeI
Per Warming
Drawer
Requirement
located on top of
the oven.
Per Warming
Drawer
Requirement
1" (2.5 cm) Min. Above Toekick or
Adjust to Oven Installation
Height
1" (2,5 cm) Min. Above
NOTE: Additional clearances between cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior depth and
height.
Toekick
° When installing a Warming Drawer below
a single or double oven, a separate 120V,
60 Hz, properly grounded receptacle must
be installed. Refer to installation instructions
packed with the Warming Drawer for
specific installation requirements.
12
Cabinetry
IAICutoutfor 30"(76.2 cm) Single Ovens only Below an Advantium or Betweenan
Advantium and a Warming Drawer
For JTP30, JTP70, PT916, PT920, ZET938
Single 30" (76.2 cm)
Oven Below
an Advantium
models only.
Single 30" (76.2 cm) Oven
Between an Advantium
and a Warming Drawer
Requirement
Per Advantiu
Requirement
3" (7.6 cm) Min.
3" (7.6 cm) Min.
2" (5.1 cm) Min.
Note: Install the
oven only with
specific models
listed on the label
located on top of
the oven.
NOTE: Additional clearances may be
required. Check to be sure the oven
supports above the Warming Drawer
do not obstruct the required interior depth
and height. The middle rail separating the
openings may need to be larger than the
2" (5.1 cm) minimum shown. Always refer to
the individual installation instructions packed
with each product for specific requirements.
NOTE: The middle rail separating the two
openings may need to be larger than the 3"
(7.6 cm) minimum shown. Always refer to the
individual installation instructions packed with
each product for specific requirements.
Combined Advantium
Oven Installation:
Per Warming
Drawer
Req
and Wall
When installed in combination with a
single wall oven, use separate electrical
junction boxes.
. Refer to the Advantium oven installation
instructions for electrical requirements
of
that product.
. These connections must be made
Warming Drawer
Combined with Advantium
and Single Oven:
Install a separate 120V, 60Hz, properly
grounded receptacle. See installation
instructions packed with each product
for specific requirements.
by a qualified electrician. All electrical
connections must meet National Electrical
Code or prevailing local codes.
13
Installation Instructions
Electrical Connections
ATTENTION
Turn off the circuit breaker or remove
fuses to the oven branch circuit.
INSTALLER
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT permitted
on these products.
With the oven supported on a table or
platform in front of the cabinet opening,
connect the flexible conduit to the
electrical junction box as shown below.
Position the conduit in such a manner
that it will lie on top of the oven in
a natural loop when the oven is
installed. You will need to purchase
an appropriate strain relief clamp to
complete the connection of the conduit
to the junction box.
DO NOT shorten the flexible conduit.
The conduit strain relief clamp must be
securely attached to the junction box
and the flexible conduit must be securely
attached to the clamp. If the flexible
conduit will not fit within the clamp, do not
install the oven until a clamp of the proper
size is obtained.
Junction Box
Location
NOTE TO ELECTRICIAN:
The 3 power
leads supplied with this appliance are
UL recognized for connection to heavier
gauge household wiring. The insulation
of these 3 leads is rated at temperatures
much higher than the temperature
rating
of household wiring. The current carrying
capacity of the conductor is governed
by the wire gauge and the temperature
rating of the insulation around the wire.
Conduit
II
WARNING:
Improper
connection of aluminum house
wiring to copper leads can
result in an electrical hazard or fire.
Use only connectors designed for
joining copper to aluminum and follow
the manufacturer's
recommended
procedure closely.
oven on a
support to assist i
connecting conduit
U
14
_-_
Strain Relief Clamp
(not included)
must be used at
Junction Box
Installation Instructions
New Construction and
Four-Conductor Branch
Circuit Connection
• When installing
in new construction,
• When installing
in a mobile home, or
• When installing
in a recreational
Three-Conductor
Branch
Circuit Connection
When connecting to a three-conductor
circuit, if local codes permit:
or
vehicle,
branch
a. Connect the bare oven ground conductor
with the crimped neutral (white) lead to
the branch circuit neutral (white or gray
in color), using a wire nut.
or
• When local codes do not permit grounding
through neutral:
a. Cut the neutral (white) lead from the crimp.
Re-strip the neutral (white) lead to expose
the proper length of conductor.
[__ound
[email protected]_
and
Ground
o,
_'-_
II
_
Neutral Wires
JcUnTt_onBox
b. Connect the oven red lead to the branch
circuit red lead in accordance with local
codes, using a wire nut.
c. Connect the oven black lead to the branch
circuit black lead in accordance with local
codes, using a wire nut. If the residence
red, black or white leads are aluminum
conductors, see WARNING on page 14.
b. Attach the appliance grounding lead (green
or bare copper) in accordance with local
codes. If the residence grounding conductor
is aluminum, see WARNING on page 14.
d. Install Junction
c. Connect the oven neutral (white) lead to
the branch circuit neutral (white or gray)
in accordance with local codes, using a
wire nut.
d. Connect the oven red lead to the branch
circuit red lead and the oven black lead to
the branch circuit black lead in accordance
with local codes, using wire nuts. If the
residence red, black or white leads are
aluminum conductors, see WARNING
on page 14.
e. Install Junction
Box Cover.
15
Box Cover.
Installation Instructions
lcl Securing the Oven in the Opening
I_
Sliding the Oven Into the
Drilling the Pilot Holes and
Mounting the Oven
Opening
a. Loop (do not tie) a 36" (91 cm) string
around the conduit before the oven is slid
into place. This will keep the conduit from
falling behind the oven.
NOTE: Before drilling the pilot holes,
make sure the oven is pushed as far
back into the opening as it will go
and centered.
i
a,
Pull out on
string loop
while pushing
the oven into
the cabinet
i
Drill through the mounting holes (top and
bottom) of the side trim, for the #8 screws
provided.
Mounting
Hole
Locations
(Hole
may vary)
b. Lift oven into cabinet cutout using the oven
opening as a grip. Carefully push against
oven front frame. Do not push against
outside edges.
The screws must
be a minimum of
1/4" (6 mm) from
the front of the
cutout.
1111_
c. As you slide the oven back, pull the string
so that the conduit will lie on top of the
oven in a natural loop.
WARNING:
Mounting
screws must be used.
Failure
to
do so could result in the oven
falling out of the cabinet causing
serious injury.
d. When you are sure the conduit is out of the
way, slide the oven 3/4 way back into the
opening. Remove the string by pulling on
one end of the loop.
i
b. Secure the oven to cabinet with screws
provided.
NOTE: If the cabinet is particle board, you
must use #8 x 314" particle board screws.
These may be purchased at any hardware
store.
16
Installation Instructions
Installing the Metal
Bottom Trim
Preparing for the Bottom
Trim Installation
a. With oven installed, take the bottom trim
and center it on the bottom front edge of
the cabinet opening.
b. Using the trim
as a template,
mark the center
of each slot
(two total) where
the mounting holes
will be drilled.
c. Remove the trim.
d. Drill pilot holes into
the center of each
template mark.
a.
For 27" (68.6 cm)
Place the bottom metal trim centered over
the pre-drilled mounting holes. Tape the
edges of the trim down to maintain the
alignment.
Tmi°m_i_
p_oitsi_i_o°,_er_jllllll
I
b. Using
two trim screws provided, secure
the bottom trim to the bottom edge of the
cabinet.
Mark (2) Mounting _IIH
Hole Locations
_J_i
here
,
__,2
* Remove
Lower Trim
Before
Pre-drilling
Mounting
Holes
cm)
Lower Trim
models with
Lower Trim in
Position, Mark
(2) Mounting
Hole Locations
here
Side
_,
Side
"_'_!,
t _I_Y2
Trim Screw Locations for
30" (76.2 cm) models with
Lower Trim
IMPORTANT: If this unit is ever
removed from the cabinet or the oven
is ever pulled out for service, the trim
must be removed first or damage to
the trim will occur.
17
Installation Instructions
151Replacing the Oven Door
NOTE: The oven door is heavy. You
may need help lifting the door high
enough to slide it into the hinge slots.
Do not lift the door by the handle.
I-_
Open
the oven door as far as it
will
open.
r-_
Push the hinge locks up against the
front frame of the oven cavity, to the
locked position.
i
Hinge in
Locked Position
Lift the oven door by
placing one hand on
each side. The door is
heavy, so you may need
help. Do not lift the door
by the handle.
Notch of Hinge
Securely Fitted
into Bottom
Hinge Slot
r-_
r-_
With the door at the same angle as
the removal position, which is most of
the way closed, seat the notch of the
hinge arm into the bottom edge of the
hinge slot. The notch of the hinge arm
must be fully seated into the bottom
of the slot.
Hinge Arm
Bottom Edge
of Slot
Hinge Notch
18
Close the oven door.
Installation Instructions
Pre-Test Checklist
I_
emove all protective
and any stickers.
I_
heck to be sure that all wiring is
secure and not pinched or in contact
with moving parts.
Check that the bottom trim is installed
properly (see page 17).
film, if present,
Check to be sure the mounting screws
are installed and flush with the side trim
(see page 16).
t Operation Checklist
Remove all items from the inside
of the oven.
I&_
Check that conduit is securely
connected to the junction box.
Turn on the power to the oven. (Refer
to your Owner's Manual.) Verify that
the bake and broil units, and all
cooking functions operate properly.
Check that the circuit breaker is not
tripped nor the house fuse blown.
NOTE TO ELECTRICIAN:
The power
leads supplied with this appliance
are UL recognized for connections
to larger gauge household wiring.
The insulation of these leads is
rated at temperatures
much higher
than the temperature
rating of
household wiring. The current
carrying capacity of a conductor
is governed by the wire gauge and
also the temperature
rating of the
insulation around the wire.
NOTE: ALUMINUM
See your Owner's Manual for
troubleshooting
list.
A.
WIRING
WARNING:
IMPROPER
CONNECTION
OF ALUMINUM
HOUSE WIRING TO THE COPPER
LEADS CAN RESULT IN AN
ELECTRICAL HAZARD OR FIRE.
B. Splice copper wires to aluminum
wiring using special connectors
designed and UL approved for
joining copper to aluminum,
and follow the manufacturer's
recommended
connector
procedure closely.
NOTE: Wire used, location and
enclosure of splices, etc., must
conform to good wiring practice
and local codes.
19
Notes
20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement