advertisement
▼
Scroll to page 2
of 17
Content Accessories ………………………………………………………………………………………………………………………………………...02 Unit Installation………………………………………………………………………………………………………………………………..03 Wire Connection………………………………………………………………………………………………………………………………03 Parking Brake Connection ………………………………………………………………………………………………………04 Speaker connection……………………………………………………………………………………………………………………….05 Button Description………………………………………………………………………………………………………………………….06 Remote Control………………………………………………………………………………………………………………………………..07 Main Menu…………………………………………………………………………………………………………………………………………...09 Radio Operation……………………………………………………………………………………………………………………………….09 USB /SD Operation………………………………………………………………………………………………………………………..10 Settings Operation ………………………………………………………………………………………………………………………..10 Bluetooth Operation……………………………………………………………………………………………………………………..12 Aux-In Operation ……………………………………………………………………………………………………………………………13 Troubleshooting ……………………………………………………………………………………………………………………………..15 General Specification…………………………………………………………………………………………………………………..16 To ensure safety while driving and to comply with laws, drivers should not watch video or operate the video device while driving. 01 Accessories Package contains the following accessories for installation and operation of the unit. (1) Washer, Spring (2) Washer, M5 Nut (3) Screw (4) Bolt (5) Mounting Strap Remote Control (5) Rubber Cushion 1 (6) Screw 1 1 8 1 Left 1 Right (7)installation bracket 1 1 Power Cable Trim Ring 02 User Manual Unit Installation Bracket Screw 1. Put the 2 brackets to the left and right side of the unit; 2. Use screws to fix the brackets to the unit. Wire Connection The Description of the Input/output Interface of the Rear Chassis. 03 Parking Brake Connection In order to view videos, the parking brake wire must be connected, and the vehicle stopped. Connecting the reversing line to taillight on the car 04 Speaker Connection After connecting, when you start up the reverse gear, the unit will receive the picture from car rear view camera. Connect the speakers according the following diagram, incorrect connections will damage the unit or your loudspeakers. Correct connection Left front - Right front | Left rear - Right rear Incorrect connections 05 Button Description 1 7 8 2 3 4 5 6 1. MIC 2. RETURN Button Press it back to main previous menu. 3. HOME BUTTON Press home button to return back to main menu. 4. SOURCE BUTTON Press source button to change mode. 5. POWER / MUTE Button /VOL Press it to turn on the unit. Press and hold for 2 seconds to turn the unit off .Press the button. briefly to mute .Please notes that the volume will be muted on all audio output connector. Press VOL knob to power on unit and Press and hold for 2 seconds to turn the unit off Rotate VOL knob to increase or reduce the volume. 6. USB/SD/AUX USB for Multimedia playback files only. insert a USB into this slot and the unit will automatically start reading and playback. * Supported Music File Format: MP3, WMA files. SD card slot, for Multimedia playback files only. Insert a SD CARD into this slot and the unit will automatically start reading and playback. * Supported Music File Format: MP3, WMA files Put the Aux plug into the Aux-In jack which was marked on front panel. 7. Display Display Information when operation the unit. 8. Remote Sensor Remote control signal receiving window. Max distance is 6-8 meters, 45 angels. 06 Remote Control 1 ○ 2 ○ 3 ○ 4 ○ 5 ○ 6 ○ 10 ○ 7 ○ 11 ○ 8 ○ 12 ○ 9 ○ 13 ○ 1: POWER 2: MODE 3: LEFT 4: PREVIOUS/Accept 5: VOLUMN DOWN 6: MUTE/BLUETOOTH 7: UP 8: OK 9: DOWN 10: MENU 11: SERARCH 12: RIGHT 13: NEXT/REJECT 14: VOLUMN UP 14 ○ 1. POWER button Power on or power off. 2. MODE button Press it to select the mode: radio, USB (if there is a USB device in the unit), SD (if there is a SD/MMC card in the unit), Bluetooth, Aux-In. 3. LEFT button Press it to move the cursor left. 4. / ACCEPT button to skip to the previous track, press and hold button for two In USB, SD mode, press seconds to activate fast reverse (REW) search in a track. button to select station backward automatically, touch again will stop In radio mode, press and hold button frequency down. select station. In Bluetooth mode, press to make a call after inputted a phone number or accept an incoming call. 5. VOLUME DOWN button Press to decrease volume level. 6. Mute button/Bluetooth button Short press to mute the volume output, press again to resume volume. Long press this button to enter into Bluetooth mode (Handsfree). 7. UP button Press it to move the cursor up. 8: ENTER Press it to confirm your selection. 9. DOWN button Press it to move the cursor down. 07 Remote Control 10. MENU Press it to show main menu. 11. SEARCH button Press it to search the radio station automatically. 12. RIGHT button Press it to move cursor right. 13. NEXT/REJECT button button to skip to the next track, press and hold button for two seconds to In USB, SD mode, press activate fast forward (FF) search in a track. button to select station forward automatically, touch again will stop In radio mode, press and hold button frequency up. select station. In Bluetooth mode, press to reject a call. 14. VOLUME UP button Press to increase volume level. Note: The distance may vary according to the brightness of ambient light. If the remote is not used for an extended period of time, remove the battery to prevent possible damage from battery leakage and corrosion. Do not place any objects between the remote control unit and the sensor on the unit. Do not drop the remote control onto the floor; it will damage it beyond repair. Do not use the remote control unit, while simultaneously operating the remote control unit of any other equipment; they may interfere resulting in improper operation. The battery normally last for about one year although depending how often the remote control is used. If the remote control unit isn’t working even when it is operated near the unit, replace the battery with a new battery of the same make and use only a lithium cell battery type: CR2025 (3V). Dispose empty batteries in accordance with your local governmental regulations. Do not short-circuit, disassemble, heat or dispose of fire or flames the battery. Keep the battery out of reach of children, should the battery be swallowed, immediately consult a doctor. 08 Main Menu The best way to discover the program is to explore each screen in detail, and to find out how to move from one to another. Read this chapter for a guided tour. Unit starts by displaying the main menu. This is the root of the screen hierarchy, and you can simply access all features by tapping on the touch screen buttons. Tap the icons to enter a desired mode. Slip the screen left and right to switch between the 2 menu pages. Page 1 Page 2 Radio Operation To start radio, tap radio button on main menu screen. Touch it to select station backward manually, touch and hold this icon to select station backward automatically. Touch it to select station forward manually, touch and hold this icon to select station. forward automatically. Touch it to select FM1—>FM2—>FM3. Touch it to select AM1—>AM2. Long Touch it to select station forward automatically. Touch again will stop select station. Long Touch it to select station backward automatically. Touch again will stop select station. Touch this button can turn on or turn off Local function. Touch this button to select mono sound reception. Touch this button can scan the stations from 1-6, Long Touch it to save the stations with good reception automatically and scan each station for about 5 seconds. Touch this button go to setting mode. Touch this button to adjust the brightness of TFT panel. Touch this button to return to main menu. 09 USB/SD Operation When a file of USB or SD card is played (music, video, photo), the screen will show following interface: Press it to repeat REP 1 => REP DIR => REP ALL Press it to skip to the previous track. Play/pause button. Press it to skip to the next track. Press it to play track randomly Rotate the image in the sequence of ×90×180×270×360 Zoom the image in or out in the sequence of ×2×3×4×5×1/2× 1/3 ×1/4 Press it to all file Press it to play video Settings Operation Setting Control Your device has default system setting, you can customize the settings to suit your personal needs. Once you change settings, your new settings will remain until you change it again. To start setting, tap it on main menu. General Control OSD Language : select English /Spanish Wallpaper :select and change the wallpaper setting Panel Adjust :calibrate the touch panel Radio Area :select radio area, from Europe— USA— South America—Russian— Asia Clock & Calendar :setting the clock and date SWC Key Beep : program Steering Wheel Control :set beep sound on or off Standby Display :set standby display on or off Version Restore Default Tap Wallpaper button to setup wallpaper 10 : just show you the firmware version Settings Operation Tap calendar setting button to calendar Tap SWC item to program SWC There are 3 wires for SWC function, connect to SWC1 (white), SWC2 (Brown), GND (Black) 1) First check whether the car has steering wheel button. 2) The steering wheel and the unit must be connected on the line. 3) While holding down the button on the steering wheel and the corresponding button on the SWC interface it will display complete setting. When all the buttons on the steering wheel and the corresponding button on the SWC interface complete setting, you can use the steering wheel button to operation the unit, such as in radio mode, press button or button to search station backward or forward. Note: 1. The “Enter” button and the “reset” button are not included in steering wheel, press the “enter” button to confirm the select, press the “reset” button to clear the former select. 2. The restriction of use SWC is the voltage between the adjacent buttons are above 0.2V that can be identified. Settings Operation Sound Control Sound Effect Subwoofer Loudness : select on/off Loud Cut off Freq: EQ : select Electric—Flat Reset User—Classic—Rock—Pop—Jazz— Subwoofer Connect the subwoofer to the unit using sub output (see electrical diagram), tap menu on screen enter into main menu setting choose setting menu. choose sound and set subwoofer on to enable subwoofer. Parking When the car is stopped and the parking brake is working, the screen can display the video image, otherwise the screen can't display the video image. Back View Camera This unit is equipped with back view camera output. The camera is used to observe the situation behind the vehicle when you are backing the car. Please connect your back view camera with the back car video input. And connect the reverse wire for back a car with the rear gear light. Rear view camera picture will be enabled when you are backing the car. 11 Bluetooth Operation Bluetooth section To enter bluetooth mode, you can tap bluetooth icon on main menu or long press the mute/bluetooth button on the remote control or press mode button on remote. Tap calling button to use phonebook functions. Tap bluetooth connect. Tap calling key pad menu. Tap call history. Pairing Mode At the 1st time when using bluetooth, you need to pair the mobile phone first. When a phone has not been paired with the unit, the BT icon and pairing mark will blink continually on the panel. When the unit have connect with phone, the BT icon will turn on and the mobile phone name (if available) will be display on the panel. According to mobile pairing device manual, after searching new device (BT friendly name: Planet Audio P650MB) select it, input password "0000" and confirm ok, device paring is finished. The phone name will available on the panel after the pairing is completed. It means device is connected and ready for bluetooth communication. Calling Button Tap on calling button to enter call mode. In call mode, the unit can be used as your phone, making and receiving calls are possible with bluetooth, simply tap phone number and tap to accept a call, and tap button to make a call. button button to hang up. and tap button for 3-4 seconds, the device 1) Tap the automatically makes a call to the latest call in its call log. 2) The volume will be operated separately while calling. (A2DP) Streaming Music Mode 12 Bluetooth Operation Tap music button enter to listen music for bluetooth in Streaming mode. Tap the button to played and paused ‘music’ in bluetooth main menu. You can select the function with the key for previous and next. A2DP (Advanced Audio Distribution Profile) Music Player A2DP is a function which can receive the audio frequency signal from the mobile phone, amplified by the car audio and played out by the car speakers. Notice: your mobile phone need to support A2DP. Tap the buttons on the screen as shown, or press corresponding buttons (pause/play, stop, previous/next) on remote control to play, pause, play previous, or next music file. Aux-In Aux-In MODE To start Aux-In Mode, tap Aux-In icon from main menu screen. connect the external audio signal source to this unit will display “NOW PLAYING”. Note: Aux-In does not support a video display function. So, there is “NO SIGNAL DETECTED” displayed if no audio signal input. Press the icon to be back to main menu. 13 Troubleshooting Symptom Power does not turn on (No sound is produced) General No sound output when operating the unit with amplifiers or power antenna attached Cause Remedy Fuse is blown Replace with fuse of the same amperage. If the fuse blows again, consult your store of purchase In correct wiring Consult your local retailer Power antennal lead is shorted to ground, excessive current is required or remote on the amplifiers or power antenna 1. Turn off the unit 2. Remove all wires attached to the power antenna lead, check each wire for a possible short to ground using an ohm meter 3. Turn on the unit 4. Reconnect each amplifier remote wire to the power antenna lead one by one. If the amplifiers turn off before all wires are attached, use an external replay to provide remote-on voltage (excessive current required) Unit needs to be Reset Using a pen or toothpick, press and release the Reset button. Panel or main unit Connectors are dirty Wipe the dirt off with a soft cloth moistened with cleaning alcohol Nothing happens when buttons are pressed Display is not Accurate 14 Troubleshooting symptom Cause Solution The car ignition is not on If the power supply is properly connected to the car accessory switch the ignition key to “ACC” The fuse is blown Replace the fuse Volume is in minimum Adjust volume to a desired level Wiring is not properly connected Check wiring connection No power No sound The operation keys do not work The built-in microcomputer is not operating properly due to noise Front panel is not properly fix into its place Sound skips The radio does not work, the radio station automatic selection does not work Press the power button for about 10 seconds to reset the unit The installation angle is more than 30 degrees Adjust the installation angle to less than 30 degrees The disc is extremely dirty or defective Clean the compact disc/try to play a new one The antenna cable is not connected the signals are too weak Insert the antenna cable firmly select a station manually 15 General Specification General Power supply Current consumption Maximum power output 11~16V DC Max. 10 A 80W x 4 channels (max) Compatible formats MP3,WMA,JPEG,AVI Dimensions (W x D x H) / weight 6.5” x 7.0” x 3.9” /4.15 lbs Working temperature range TFT display Screen size Resolution Aspect ration Brightness Contrast ratio FM radio Frequency range(Europe area) Frequency range(America area) Frequency range(Asia area) Frequency range(South America area) Frequency range(Russia area) -4°F -- +140°F FM:87.5 FM:87.5 FM:87.5 FM:87.5 FM:87.5 Preset memory stations 18 AM(MW)radio Frequency range(Europe area) Frequency range(America area) Frequency range(Asia area) Frequency range(South America area) Frequency range(Russia area) Preset memory stations Audio specification Frequency response TV Color System USB interface USB type 6.5 inch 800*480 pixel 4:3/16:9 460 cd/㎡ 500:1 –108MHz(Step 50KHz) –107.9MHz(Step 200KHz) –108MHz(Step 100KHz) –108MHz(Step 100KHz) –108MHz(Step 50KHz) 65-74MHz(Step 30KHz) AM:522-1620(Step AM:530-1710(Step AM:531-1602(Step AM:520-1710(Step AM:522-1620(Step 12 9KHz) 10KHz) 9KHz) 10KHz) 9KHz) 20 Hz-20 KHz Color system NTSC/PAL USB 2.0 full speed Specifications are subject to change without notice, mass and dimension are approximate. 16
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project