DIGITAL POWERMETER
DIGITAL POWERMETER
EPR-04S
EPR-04S
EPR-04S DIGITAL POWERMETER
FUNCTIONS OF BUTTONS
EPR-04S is a 3-phase digital powermeter and energymeter which measures:
-Active Power (W)
-Active Energy (kWh)
-Reactive Power (VAr)
-Reactive Energy (kVArh)
-Apparent Power (VA)
-Cosj
EPR-04S PC CONNECTION
These values are scrolled between by the set button (
) First 3 displays show
L1, L2 and L3 phase values and the 4th display show total value of each selected
measured value (W, VAr,VA,kWh or kVArh).
EPR-04S also measures Maximum Demand, Demand, maximum and minimum
values of power. EPR-04S has MODBUS serial interface.
31 DEVICE CAN BE CONNECTED AT SAME LINE
MAX. 1200 mt.
SET
When :
RS485/RS232
CONVERTER
B
A
1. W led lights: Active Power
2. VAr led lights: Reactive Power
3. VA led lights: Apparent Power
4. kWh led lights:
a-) A-I :Imported Active Energy
b-) A-E : Exported Active Energy
5. KVArh led lights:
a-) r-L
:Reactive-Inducitive Energy
b-) r-C :Reactive-Capacitive Energy
6. Cosj led lights :Cosj of the network
is measured.
PC
GND
ESC
Current Transformer Ratio Setup
In this menu, current transformer ratio is adjusted.
Note: If the current transformer is not used between the system and EPR-04S,
current transformer ratio is entered as 1.
Example:
; If a current transformer which has a ratio of 250/5A is used between
the system and EPR-04S; Current transformer ratio is entered as
= 250/5
= 50 .
Push SET button 5 seconds
L1
L2
L3
(Ctr menu is displayed)
DIGITAL
POWERMETER
Push SET button (The number which k
L1
EPR- 04S
is the last digit of second display
Cosj
blinks)
Operating Principle:
TR B
A GND
...
EPR-04S-31
TR B
A GND
TR B
EPR-04S-2
A GND
EPR-04S displays the energy and power values by multiplying voltage and current
ratios by values read from input. So, the displayed values are the real values of
system.
Energy Pulse Outputs
EPR-04S has 2 Energy Pulse Outputs; Pul1, Pul2.
Pul1 (Reactive Energy Pulse Output): A 400msec. pulse output is given, if measured
energymeter value increases 1 KVArh. Pul1 is used for Reactive Inductive energy
values.
Pul2 (Active Energy Pulse Output): A 400msec. pulse output is given, if measured
energy meter value increases 1KWh. Pul2 is used for both (Active Import) and
(Active Export) energy values. Min. pulse period is 1.6 sec.
9 PIN CONNEKTOR
EPR-04S-1
MAX. 1200 mt.
MAX. 1200 mt.
RS485/RS232
CONVERTER
...
EPR-04S-247
...
PC
Phase
Monitoring
Display
EPR-04S-31 EPR-04S-2 EPR-04S-1
REPEATER
Kilo led
L1
Mega led
L2
L2
Cosj
W
k
S
M
64EPR4S0/10-05
DIGITAL POWERMETER
L2
In this menu, voltage transformer ratio is adjusted.
Note: If the voltage transformer is not used between the system and EPR-04S,
voltage transformer ratio is entered as 1.
Example:
; If a voltage transformer which has a ratio of 34.5KV/100V is used
between the system and EPR-04S; Voltage transformer ratio is entered as
= 34500/100
= 345
L3
k
L3
M
EPR-04S
VAr VA kWh kWArh
Voltage Transformer Ratio Setup
Esc
Down
ESC
DIGITAL POWERMETER
W
k
S
M
Push SET button when (SAU SEt yES) appears at the display. (When
SAU SEt yES appears at the display,If you push ESC button or choose
no option instead of yES option, new data will be canceled and
previous value will be activated.
Set
SET
k
VAr VA kWh kWArh
L3
Push ESC button one by one until (SAU SEt yES) appears at the display.
Up
L1
Cosj
L2
k
L3
M
Push set button,Ctr is displayed. (Data is entered but is not activated
yet. For activating the new data please follow the below steps).
EPR- 04S
Total (S)
Monitoring
Display
8
Cosj
000
k
L2
M
By using UP-DOWN buttons, enter to the last digit of desired value.
kWh
kVArh
k
L2
M
SET
ESC
L1
k
L1
M
k
k
L1
M
000
k
By using UP-DOWN buttons,
enter to the second digit of
desired value
Set
Push SET button (The number
EPR-04S
Esc
which is the last digit of third
display blinks). If you did not
enter the second digit correct, you can reentry by pressing the ESC button
DIGITAL
POWERMETER
k
L3 k
S
L3
kWh
kVArh
Push SET button (The number which is in the middle of the third
display blinks. If you did not enter the third digit correct, you can
reentry by pressing the ESC button.
Phase Monitoring leds
L1
k
L3 k
By using UP-DOWN buttons, enter
to the third digit of desired value.
Min. and Max. values are defined for Active Power(W),reactive power(VAr) and
apparent power(VA). Demand values are defined for total active power(W),total
reactive power(VAr) and total apparent power(VA).
If measured instant value is smaller than min. value which was stored before, it
is stored as new min. value. If measured instant value is greater than max. value
which was stored before, it is stored as new max. value.
Demand value is the smallest value of the measured values in demand time. If
the smallest value of the measured values (for example 15 minute) in demand
time is greater than the demand value which was stored before, it is stored as
new demand value.
If one of defined parameters is displayed when deman button is pressed , min.,max
or demand values are displayed. When an undefined parameter is displayed if
demand button is pressed, instant value is continued to display.
For example when power factor is displayed instant values are continued to
display because min., max. and demand values are undefined.
CONNECTOR (DB9)
L2
Push SET button (First number of
the third display blinks). If you did not S
enter the fourth digit correct, you can
reentry by pressing the ESC button.
Watching of Min.,Max. and Demand Values:
B
A
GND
TRB A GND
By using UP-DOWN buttons enter to
the fourth digit of desired value.
Demand and Maximum Demand
Demand is average of power for the demand time. Demand time can be changed
between 1-60 minutes.
Maximum demand is the max. value of the average power values measured during
demand time. If the new average value exceeds the maximum demand value, the
new demand value is recorded as maximum demand.
U P TO 2 4 7 D E V I C E C A N B E C O N N E C T E D AT S A M E L I N E
B Y U S I N G R E P E AT E R .
When W led lights,it shows max.power values which are measured
instantaneously and it shows total average demand values. Also it is
used for moving upwards in the menu.
When W led lights,it shows min.power values which are measured
instantaneously and it shows total average demand demand values.
Also it is used for moving downwards in the menu.
It is used for passing between parameters such as W, Var, VA, KWh,
KVArh, cosj. When it is pressed for 5 second, adjustment mode is
entered. In the adjustment mode it is used for saving parameters and
moving to the sub menu.
In the adjustment mode, it is used for entering to the upper menu or
it is used for quiting from the adjustment mode without saving the
values.
Push SET button 5 seconds (Ctr menu is displayed)
Set
By using UP-DOWN buttons find the Utr menu.
Esc
Push SET button (The number which is the last digit of second display
blinks)
1
DIGITAL POWERMETER
DIGITAL POWERMETER
EPR-04S
EPR-04S
Push SET button 5 seconds
(Ctr menu is displayed)
000
k
SET
L1
k
L1
M
Cosj
000
W
k
L2
M
L2
L3
VAr VA kWh kWArh
Push set button,Utr is
displayed. (Data is entered but is not activated yet. For activating the
new data please follow the below steps.
L1
Push SET button 5 seconds
(Ctr menu is displayed)
Push ESC button one by one until (SAU SEt yES) appears at the display.
Push SET button whenl (SAU SEt yES) appears at the display. (When
SAU SEt yES appears at the display,If you push ESC button or choose
no option instead of yES option, new data will be canceled and
previous value will be activated.
Bu using UP-DOWN buttons
find Pýn menu.
Push SET button (Pýn ACt
menu is displayed.)
Demand Time Setup:
L1
Push SET button 5 seconds
(Ctr menu is displayed)
L1
L2
L3
DIGITAL
POWERMETER
k
Cosj
EPR- 04S
L3
By using UP-DOWN buttons, enter
to the second digit of desired value
S
By using UP-DOWN-SET
button enter the new
password
000
k
SET
Cosj
L1
k
L1
M
Cosj
000
W
k
L2
M
L2
L3
k
L3
M
VAr VA kWh kWArh
DIGITAL POWERMETER
Esc
Voltage
Measuring Input
k
L1
M
W
k
L2
M
L2
L3
k
L3
M
VAr VA kWh kWArh
Set
k
S
M
EPR-04S
Esc
DIGITAL POWERMETER
L1 L2 L3
N
1
4
2
3
IL1
5 6
k
K
L1
L2
l
L
7 8
9 10
In this menu, values of min.,max. or energymeters are erased.
It saves the instantaneously measured min. and max. values of EPR04S into its memory. Please kindly look at to the section of
FUNCTIONS OF BUTTONS for min. and max. values.
Note: Informations which are saved to the memory are not affected
from the electric interruptions.
In the CLr dE or En menu ; when you choose and quit from all menus,
if you confirm the changes,min. and max. values of all parameters or
values of energymeters are erased at the same time.For erasing the
values of min. and max. or energymeter;In the measurement position,
By using UP-DOWN buttons
find Pýn menu.
L1
Push SET button (Pýn ACt menu
is displayed.)
L2
2
L2
L3
Cosj
l
L
+
_
18 17 16 15
24 23 22 21 20 19
TR B A GND
RS-485
18 17 16 15
TR B A GND
RS-485
k
K
l
L
k
K
4
5 6
2
3
IL2
IL3
Un
7 8 9 10
13 14
l
L
k
K
L2
l
L
k
K
L3
Current
Measuring Input
IL1
L1 L2 L3 N
2
3
4
5 6
k
K
L3
IL2
IL3
7 8
9 10
l
Lk
K
l
L
3 Phase without neutral current input with
Aron wiring configuration
Max: 30 VDC
+
_
(12-48V DC)
+ + -
18 17 16 15
24 23 22 21 20 19
TR B A GND
RS-485
Voltage
Measuring Input
Auxiliary
Supply
Un
13 14
1A
l
L
k
K
N
1A
Max: 30 VDC
Voltage
Measuring Input
L2
ESC
N
1
+ + -
L1
SET
L1 L2 L3
IL1
L1
24 23 22 21 20 19
1
000
13 14
Auxiliary
Supply
Current
Measuring Input
+
_
EPR- 04S
kWh
kVArh
Voltage
Measuring Input
Un
(12-48V DC)
k
k
k
K
Max: 30 VDC
Auxiliary
Supply
3 Phase neutral
DIGITAL
POWERMETER
k
L3 k
Push SET button (The number
S
which is the last digit of second
display blinks)
3 Phase without neutral current input with
Aron wiring configuration
1A
N
L1
L3
+ + -
IL3
L3
Push SET button 5 sn.
(Ctr menu is displayed)
Monitoring and Erasing of minimum and maximum values:
l
L
(12-48V DC)
IL2
This menu is used for activating the user password.
After the user password is activated for entering to the menus;
while the instant values are observed,user password is required
if the
button is pushed for 5 sn. If the user password is
entered wrong device does not latch
Note: Factory default value of user password is 1234
For activating the user password; In the measurement mode,
Push SET button when (SAU SEt yES) appears at the display.
(When SAU SEt yES appears at the display,If you push ESC
button or choose no option instead of yES option, you quit
from adjustment menu without saving new settings and device
continues to work with previous settings.
L2
Max: 30 VDC
Current
Measuring Input
Activating the user password:
Push ESC button one by one until (SAU SEt yES) appears at
the display.
l
L
IL3
SET
Push SET button when (SAU SEt yES) appears at the display.
(When SAU SEt yES appears at the display,If you push ESC
button or choose no option instead of yES option, you quit
from adjustment menu without saving new settings and device
continues to work with previous settings.
Set
k
S
M
Push set button,dt is
EPR-04S
displayed. (Data is entered
but is not activated yet.
For activating the new data please follow the below steps).
k
K
IL2
ESC
Push SET button, Pýn CHg is displayed. Data is entered but is not
activated yet. For activating the new data please follow the below
steps).
Push ESC button one by one until (SAU SEt yES) appears at the
display.
Push SET button (The number which is the last digit of third display
blinks). If you did not enter the second digit correct, you can reentry
by pressing the ESC button.
k
K
L1
24 23 22 21 20 19
EPR- 04S
000
k
By using UP-DOWN-SET
button reenter the new password.
ESC
IL1
N
L3
kWh
kVArh
L3 k
000
L2
L1
N
(12-48V DC)
k
Cosj
~
1A
l
L
RS-485
+
_
By using UP-DOWN-SET button enter the old password
kWh
kVArh
Un
IL3
3 Phase without neutral
DIGITAL
POWERMETER
k
k
L3 k
L3
IN1
L2
Push SET button (The number
which is in the middle of the third
display blinks.)
ESC
L2
L2
l
L
k
K
Gnd A B TR
Auxiliary
Current Measuring Input
Supply Voltage Measuring Input
+ + -
L1
By using UP-DOWN buttons
find the dt menu.
By using UP-DOWN buttons,
enter to the last digit of
desired value.
L1
By using the UP-DOWN buttons S
find Pýn CHg menu.
In this menu,demand time is adjusted .
k
K
IL2
PR-16 Box Connection Diagram
This menu is used for changing the user password .
Note: Factory default value for user password is 1234
For changing the user password;In the measurement mode,
Esc
IL1
N
L3
L2
Changing of User Password:
Set
EPR-04S
DIGITAL POWERMETER
L2
L1
N
1A
L1
In this menu user password is defined and activated.
You must define and activate a 4 digit user password for preventing
device settings from the illegal usage.
There are 2 sub menu under the Pýn menu.
k
L3
M
k
S
M
~
User password Setup:
Push SET button (The number which is the last digit of third display
blinks). If you did not enter the second digit correct, you can reentry
by pressing the ESC button
By using UP-DOWN
buttons, enter to the last
digit of desired value.
Un
Push ESC button.
By using UP-DOWN buttons, enter to the second digit of desired value
RS-485
Auxiliary
Current Measuring Input
Supply Voltage Measuring Input
Push SET button.
(CLr dE is displayed)
ESC
Gnd A B TR
IN2
INC
PUL2
PUL1
PULC
Push SET button (The number
which is in the middle of the third S
display blinks. If you did not enter
the third digit correct, you can
reentry by pressing the ESC button.
By using the UP-DOWN buttons ;
If you want to delete the values choose
yEs, if not choose no.
IN1
kWh
kVArh
L3 k
IN2H
IN2L
IN1H
IN1L
PUL1H
PUL1L
PUL2H
PUL2L
Push SET button.(CLr dE no
menu is displayed)
k
(12-48V DC)
- + - +
(12-48V DC)
- + - +
Current
Measuring Input
L1 L2 L3
N
IL1
1
4
5 6
2
3
IN2
INC
PUL2
PUL1
PULC
Cosj
EPR- 04S
+
_
+
_
By using the UP-DOWN buttons
find the CLr dE or En menu.
DIGITAL
POWERMETER
IN1
L3
IN2H
IN2L
IN1H
IN1L
PUL1H
PUL1L
PUL2H
PUL2L
L2
L2
k
IN1
L1
IN2
INC
PUL2
PUL1
PULC
L1
Push SET button (First number of
the third display blinks). If you did
not enter the fourth digit correct,
you can reentry by pressing the
ESC button.
By using UP-DOWN buttons, enter
to the third digit of desired value.
Max: 30 VDC
Max: 30 VDC
IN2
INC
PUL2
PUL1
PULC
By using UP-DOWN buttons enter to the fourth digit of desired value.
IL2
18 17 16 15
TR B A GND
RS-485
Auxiliary
Supply
IL3
Un
7 8 9 10
N
13 14
1A
L1
L2
l
L
L3
3 Phase without neutral
7
k
K
l
L
k
K
l
L
3 Phase without neutral current input with
Aron wiring configuration
N
DIGITAL POWERMETER
DIGITAL POWERMETER
EPR-04S
EPR-04S
PR 19 Box Connection Diagram
L1
K
L2
k
By using UP-DOWN buttons enter to the fourth digit of desired value.
L
K
l
L
k
L3
K
l
L
k
N
1
2
IL1
3
4
L1
K
L2
k
5
IL2
( 12-48V DC )
InC In1 In2
L3
6
IL3
1
6
5
Pul C
( 12-48V DC )
InC In1 In2
IL3
GND A B TR
Pul 2
Auxiliary
Supply
Voltage Measuring Input
12
L2
8
L1
7
L1
N
Push SET button (The number which
is the last digit of third display blinks).
If you did not enter the second digit
correct, you can reentry by pressing
the ESC button)
N
10
L3
9
11
By using UP-DOWN buttons,
enter to the last digit of desired
value.
12
3 Phase neutral
L1
N
3 Phase without neutral current input with
Aron wiring configuration
ESC
W
k
L2
M
L1
L2
K
L2
k
L
K
l
L
k
L3
K
l
L
k
1
2
IL1
3
4
5
IL2
L1
K
L2
L3
L2
k
EPR- 04S
kWh
kVArh
By using UP-DOWN buttons find
000
k
SET
l
1
Pul 2
L2
8
Pul C
Auxiliary
Supply
N
10
11
1A
L3
9
4
5
IL2
Max: 30 VDC
GND A B TR
Voltage Measuring Input
L1
7
IL1
3
( 12-48V DC )
InC In1 In2
13 14 15 16 17 18
Pul 1
L2
8
L1
7
L1
N
N
10
11
Max: 30 VDC
Max: 30 VDC
+
_
Auxiliary
Current Measuring Input
Supply Voltage Measuring Input
~
L1
1A
L2
L3
N
L1
L2
L3
N
k
K
IL2
l
L
Un
~
1A
k
K
l
L
L1
k
K
RS-485
Auxiliary
Current Measuring Input
Supply Voltage Measuring Input
IL3
l
L
L2
L1
L2
L3
N
IL1
IMPORTANT NOTE: In order communicate with ENTES software Baudrate has
to be 38400 bps and parity has to be no
MODBUS RTU PROTOCOL
Standart MODBUS RTU message is shown below.
T
Adjustment of Parameters
Adjustment of Device ADDRESS
12
By using UP-DOWN buttons find
L1
N
IL3
l
L
k
K
l
L
FUNCTION
8 BIT
ADDRESS
8 BIT
DATA
NX8BIT
CRCH
CRCL
T
The T times corresponds to a time in which data must not be exchanged on the
communication bus to allow the connected devices to recognize the end of one
message and the beginning of another. This time must be at least 3.5 characters
at the selected baud rate. Adress range (1-247 ) is address of the connected
device. The data field contains data sent to the slave by master or data sent to
master by slave.
Push SET button 5 sec.
bulun
CRC is a error check method by using MODBUS RTU protocol and consists of
2 bytes.
Push SET button again.
Available Modbus Function:
ESC
03H
READ HOLD REGISTERS
06H
PRESET SINGLE REGISTER
10H
PRESET MULTIPLE REGISTERS
Read Hold (03) function is used for reading measured values and transformers ratio.
Registers can be read are between 0-68. For example to read phase1 voltage;
001
01 03 00 00 00 01 84 0A
Push SET button when (SAU SEt yES) appears at
the display. (When SAU SEt yES appears at the
display,If you push ESC button or choose no option instead
of yES option, you quit from adjustment menu without saving
new settings and device continues to work with previous settings.
01 Device adres
03 Function
00 MSB adres
00 LSB adres
00 Register number MSB
01 Register number LSB
84 CRC MSB
0A CRC LSB
Preset Single Register (06) function is used to set transformer ratio or for clearing
one of min.,max., Demand values.
Adjustment of Baud Rate
Baud Rate can be chosen as a value of 1200,2400,4800,9600,19200, 38400 bps
Push SET button 5 sec.
k
K
3 Phase without neutral current input with
Aron wiring configuration
6
IL2
N
L3
3 Phase neutral
DIGITAL POWERMETER
002
Gnd A B TR
IN2H
IN2L
IN1H
IN1L
PUL1H
PUL1L
PUL2H
PUL2L
IN2H
IN2L
IN1H
IN1L
PUL1H
PUL1L
PUL2H
PUL2L
RS-485
Push SET button when (SAU SEt yES) appears at the display.
(When SAU SEt yES appears at the display,If you push ESC
button or choose no option instead of yES option, you quit
from adjustment menu without saving new settings and device
continues to work with previous settings.
VAr VA kWh kWArh
Push ESC button one by one until (SAU SEt yES) appears
(12-48V DC)
- + - +
Gnd A B TR
W
k
S
M
Push SET button for saving the new value.
+
_
(12-48V DC)
- + - +
Push ESC button one by one until (SAU SEt yES) appears
k
L3
M
By using UP-DOWN buttons adjust the desired value.
PK 26 Box Connection Diagram
Push SET button for saving the new value.
L3
L2
EPR-04S has MODBUS RTU communication protocol which is optical isolated. All
measured parameters can be transfer to the computer.Transformer ratios and
parameters of communication can be set. Saved demand and energy values can
erase
Auxiliary
Supply
3 Phase without neutral current input with
Aron wiring configuration
IL1
IL3
Pul 2
L3
9
By using UP-DOWN buttons adjust the desired value.
Serial Communication
GND A B TR
Voltage Measuring Input
12
3 Phase without neutral
Un
6
RS485
19 20 21 22
1A
+
_
Pul 1
2
Current Measuring Input
RS485
19 20 21 22
13 14 15 16 17 18
l
6
IL3
+
_
Pul C
( 12-48V DC )
InC In1 In2
000
L
k
Current Measuring Input
Max: 30 VDC
Cosj
K
bulunuz
Push SET button again.
ESC
Push SET button, Pýn ACt oF is
displayed (Data is entered but
is not activated yet. For activating the new data please follow the below
steps)
Push ESC button one by one until (SAU SEt yES) appears at the
display..
k
L2
M
ESC
Push SET button 5 sec.
k
Push SET button whenl
(SAU SEt yES) appears at
Set
the display. (When SAU
EPR-04S
Esc
SEt yES appears at the
display,If you push ESC
button or choose no option instead of yES option, new data will be
canceled and previous value will be activated.
l
L3
Adjustment of Parity:
Parity can be adjust as NO, ODD or EVEN.
DIGITAL
POWERMETER
Cosj
k
L1
M
L
Push SET button when (SAU SEt yES) appears at the display.
(When SAU SEt yES appears at the display,If you push ESC button
or choose no option instead of yES option, you quit from adjustment
menu without saving new settings and device continues to work
with previous settings.
DIGITAL POWERMETER
L1
L1
Push ESC button one by one until (SAU SEt yES) appears
VAr VA kWh kWArh
k
600
Push SET button for saving the new value.
L3
k
L3
M
L3 k
S
L2
By using UP-DOWN buttons adjust the desired value.
k
S
M
L1
By using UP-DOWN buttons, enter
to the second digit of desired value
RS485
19 20 21 22
13 14 15 16 17 18
Pul 1
1A
11
4
IL2
Current Measuring Input
Auxiliary
Supply
N
10
L3
9
3
Max: 30 VDC
Pul 2
L2
8
L1
7
2
IL1
1A
+
_
Pul 1
l
Cosj
GND A B TR
Voltage Measuring Input
L1
k
L1
M
000
RS485
19 20 21 22
13 14 15 16 17 18
L
k
+
_
Pul C
K
l
l
Current Measuring Input
Max: 30 VDC
Push SET button (First number of the third display blinks). If you did
not enter the fourth digit correct, you can reentry by pressing the
ESC button
By using UP-DOWN
buttons, enter to the third
digit of desired value.
Set
Push SET button
EPR-04S
Esc
(The number which is in
the middle of the third
display blinks. If you did not enter the third digit correct, you can
reentry by pressing the ESC button)
L
ESC
Current transformers ratio can be set 5-10000, voltage transformer ratio can be
set 1-2000 min.,Max. and Demand values can be only clear. If sent value is
outside of this range device responds with an error message.
Setting CT to 100;
By using UP-DOWN buttons find
Push SET button again.
9
3
DIGITAL POWERMETER
DIGITAL POWERMETER
EPR-04S
EPR-04S
You may change setup parameters using the MPR-SW-1 / SW-2 Software: Set
Transformer ratios, Reset Energy and Demand values and change the device address
up to 247.
MPR-SW-2 can communicate with multiple (max. 247) EPR-04S devices.
The setup software will install the MPR-SW-1/SW-2 Software under START -> ENTES
-> Mpr-SW.exe directories. You may browse and run it
18
90mm
90mm
96mm
143
79.3mm
70mm
121
34.5
138.4
143
Type PR 19 (96x96)
DESCRIPTION
58mm
50mm
Type PR 16
96mm
58mm
Type PR 16
IMPORTANT NOTICE:
SIZE
(BYTE)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Please use the softwares own EXIT buttons while quitting the menu or the Main
Window.
10.8
30.1
7.6
9.5
60.6
TECHNICAL DATA
Clicking the START button on the main window, starts the real time analysis of EPR04S device values. SETTINGS button is for setting up communication parameters
(Adress, Parity, Baud Rate) between the PC and EPR-04S device. Both side parameters
should be the same for correct data transmission. There are CLEAR ENERGY and
CLEAR DEMAND buttons for resetting those values. Transformer ratio is able to setup
with the TRANS.RATIOS button on the main menu.
The Parameters are sent in 16bit Hexadecimal format. For Example, 230V
voltage will be sent as 00E6H. Cosj values shall be divided to 100. 0.98
Cosj will be sent as 0062H. While Cosj is a negative value the MSB bit will
be sent as 1. Energy values are sent in 8 bytes (in decimal).
1234567891234,567kWh = 12 34 56 78 91 23 45 67 / 1000
Specifications for data cable ;
- 24 AWG or thicker
- Less than 100 ohm/ km
- Nominal characteristic impedance at 100 kHz of 100 ohms
- Less than 60 pF/m mutual capacitance (between two wires in a pair)
- Less than 120 pF/m mutual pair capacitance ( the capacitance between
one wire and all others connected to earth).
- Twisted Pair
Graphic Button and Statistics :
The Graphic menu, shows records and values for past 1 year period on a graphical
interface. Users are able to choose the statistics period, hourly,daily and monthly
from the window shown below.
ERROR CODES
Slave device (EPR-04S) sends error message when receive any missing query.
Error codes are given below.
01 Invalid Function: If any message except given above is used, then 01 error messages
will be sent.
02 Invalid Register: EPR-04S uses registers between 0 and 57. If any message is been
sent out of this range, then 02 error message will be sent.
03 Invalid data: If any different value is been set for dedicated Transformer values and
nonzero for demand value, then error message 03 will be sent.
Operating Voltage (Un)
: Please look at the back labels on
the device
Operating frequency (f)
: 50/60 Hz
Auxiliary supply Power Consumption: < 4 VA
Measuring Input Power Consumption
: < 1VA
VIn
: 10-300VAC 50/60Hz. (L-N)
: 10-500VAC 50/60Hz. (L-L)
IIn
: 0.05 - 5.5 A~
Measuring Range
: 0-900 M (W,VAr,VA)
Measuring Category
: CAT III
Class
: 1±1digit [(%10-%110) xFull Scale]
Voltage Transformer Ratio
: 1 ... 2000
Current Transformer Ratio
: 1 ... 2000
Demand Time
: 1-60 min. (programmable)
Serial Interface
: MODBUS RTU (RS 485)
: Optically Isolated, programmable
: Baud Rate 1200-38400 bps
: Address 1-247
: No , odd ,even Parity
Pulse Output
: NPN Transistor
Switch Period
: Min. 1,6 Sec. (400 msec pulse
width)
Operation Current
: Max. 50 mA
Operation Voltage
: 5.....24 V DC, max. 30 VDC
Input
: 12...48 V DC
Ambient Temprature
: -5°C; +50°C
Display
: Red LED Display
Dimensions
: PR-19
Equipment Protection Class
: Double Insulation-Class II ( )
Box Protection Class
: IP 40
Box Material
: Non-flammable
Installation
: Panel Mounted (PR-16, PR-19)
Rail Mounted (PK-26)
Wire Thickness(for terminal block) : 2.5 mm2
Weight
: 0.45 kg (PR-19, PK-26)
0.8 kg (PR-16)
Installation Category
: Class III
26.5
106.0
10.0
Type PK-26
PRECAUTIONS FOR INSTALLATION AND SAFE USE
Failure to follow those instructions will result in death or serious injury.
- Disconnect all power before working on equipment..
- When the device is connected to the network, do not remove the front
panel.
- Do not try to clean the device with solvent or the like.Only clean with dry
cloth.
- Verify correct terminal connections when wiring.
- Electrical equipment should be serviced only by your component seller.
- No responsibility is assured by manufacturer or any of its subsidiaries for
any consequences arising out of the use of this material.
- Only for rack panel mounting.
M P R - S W -1 / S W - 2 : E P R - 0 4 S s e r i a l I n t e r f a c e S o f t w a r e
MPR-SW-1 / SW-2 Software is designed for use with EPR-04S device and analyze its
measurement values. MPR-SW -1 / SW-2 is able to view realtime measurements and
parameters on a PC screen. The software records all parameters and values into a
database for future graphical analysis. The Graphical Analysis is designed flexible
for view past records in hour,day and month periods. Inductive/Reactive and
Capacitive/Reactive values can be viewed on the main window. Energy reports can
also be viewed between specific dates.
4
21.5
53.0
58.0
8.5
S-REACTIVE POWER MAX
S-REACTIVE POWER MIN
T-REACTIVE POWER MAX
T-REACTIVE POWER MIN
R-APPARENT POWER MAX
R-APPARENT POWER MIN
S-APPARENT POWER MAX
S-APPARENT POWER MIN
T-APPARENT POWER MAX
T-APPARENT POWER MIN
ACTIVE ENERGY kWh.-1
ACTIVE ENERGY kWh.-2
ACTIVE ENERGY kWh.-3
ACTIVE ENERGY kWh.-4
ACTIVE ENERGY kWh.(EXPORT) -1
ACTIVE ENERGY kWh.(EXPORT) -2
ACTIVE ENERGY kWh.(EXPORT) -3
ACTIVE ENERGY kWh.(EXPORT) -4
REACTIVE ENERGY kVArhL-1
REACTIVE ENERGY kVArhL-2
REACTIVE ENERGY kVArhL-3
REACTIVE ENERGY kVArhL-4
REACTIVE ENERGY kVArhC-1
REACTIVE ENERGY kVArhC-2
REACTIVE ENERGY kVArhC-3
REACTIVE ENERGY kVArhC-4
VOLTAGE TRANS. RATIO
CURRENT TRANS. RATIO
DEMAND TIME (SEC.)
140mm
50mm
Dimensions
18
34.5
Tip 19
Type PR 19 (96x96)
14.0
SIZE ADDRESS
(BYTE)
2
1DH
2
1EH
2
1FH
2
20H
2
21H
2
22H
2
23H
2
24H
2
25H
2
26H
2
27H
2
28H
2
29H
2
2AH
2
2BH
2
2CH
2
2DH
2
2EH
2
2FH
2
30H
2
31H
2
32H
2
33H
2
34H
2
35H
2
36H
2
37H
2
38H
2
39H
92mm
Run The MPR-SW Program :
Wall
79.3mm
70mm
45.0
R-ACTIVE POWER
S-ACTIVE POWER
T-ACTIVE POWER
TOTAL ACTIVE POWER
R-REACTIVE POWER
S-REACTIVE POWER
T-REACTIVE POWER
TOTAL REACTIVE POWER
R-APPARENT POWER
S-APPARENT POWER
T-APPARENT POWER
TOTAL APPARENT POWER
R-COS
S-COS
T-COS
WATT DEMAND
V Ar DEMAND
VA DEMAND
WATT DEMAND MAX
V Ar DEMAND MAX
VA DEMAND MAX
R-ACTIVE POWER MAX
R-ACTIVE POWER MIN
S-ACTIVE POWER MAX
S-ACTIVE POWER MIN
T-ACTIVE POWER MAX
T-ACTIVE POWER MIN
R-REACTIVE POWER MAX
R-REACTIVE POWER MIN
92mm
Insert the Setup CD into the CD-ROM drive.
Browse the CD by double clicking My Computer and CD-Rom icons.
Run Setup.EXE by double clicking its icon or use the START menu button and
choose Run.
Write d:\setup.exe into the text box opened below.The setup program will install
the software to your computer.
90.0
00H
01H
02H
03H
04H
05H
06H
07H
08H
09H
0AH
0BH
0CH
0DH
0EH
0FH
10H
11H
12H
13H
14H
15H
16H
17H
18H
19H
1AH
1BH
1CH
Wall
MPR-SW Software Setup
01 10 00 37 00 02 00 64 00 C8 84 8F
01 Device Address
10 Function
00 MSB adres
37 LSB adres
00 Register number MSB
02 Register number LSB
04 Byte count
00 Data MSB
64 Data LSB
00 Data MSB
C8 Data LSB
84 CRC MSB
8F CRC LSB
ADDRESS DESCRIPTION
The area Measurements
on The Control Panel
140mm
01 Device Address
06 Function
00 MSB adres
37 LSB adres
00 Data MSB
64 Data LSB
D8 CRC MSB
35 CRC LSB
Preset Multiple Register(10H) is used to set more then one register at same time.
Setting CT to 100,Ut to 20;
99
01 06 00 37 00 64 D8 35
5
">
