CANARM RICH104B03CH17 Installation Guide

Below you will find brief information for Chandelier RC-2. This document provides installation instructions for the Chandelier RC-2. It includes a section on safety precautions, detailed steps for installation, and information on how to assemble the different parts of the fixture.

PDF Download

Document

Chandelier

Questions or Concerns Contact Canarm At:

1-800-265-1833 (English) or 1-800-567-2513 (French)

REQUIRED: Wrench

Pliers

Phillips Screwdriver

Wire Cutters

Monday Through Friday 8:00am - 5:00pm E.S.T.

RC-2

03/03

Wiring supplies as required by electrical code

SAFETY PRECAUTIONS:

1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.

DO NOT REMOVE INSULATION FROM FIXTURE.

2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE

BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE

HAZARDS INVOLVED.

NOTE: Product May Not Look Exactly As Shown In Figures.

INSTALLATION:

Outlet Box

Mounting

Bracket

Outlet Box Screws

Nipple

Hex Nut

Attach the mounting bracket to the outlet box using electrical box screws and flat washers. Attach the nipple to the mounting bracket and adjust until it will clear the canopy when assembled (Place the canopy over the nipple and tighten the upper connector onto the nipple until snug.

The upper connector should hold the canopy snug to the ceiling). Lock the nipple in the correct position using the brass nut.

STYLE #1A

STYLE #1B

Bulb

Shade

Tube

Finial

Shade

Note: Refer to the style of assembly that matches the style of your fixture.

If your fixture has shades,

STYLE #1A - Place shade on tube, then install bulb.

STYLE #1B - Install bulb, shade then finial.

Power

Cord

Bulb

Tube

STYLE #2 - Remove spinner nut from socket. Position glass on lamp and secure with spinner nut.

Note: Glass may face up or down.

Chain

Spread one end of chain open and fasten to the lower connector. Weave the power cord and ground wire through the links in the chain. Spread the other end of the cord open and fasten to the upper connector. Lower

Connector

STYLE #2

Spinner

Nut

Note: If your fixture has candlestyle lights, slide the tubes over the uplight sockets

Upper Connector

Canopy

F eed the wires through the hole in the upper connector. Loosen off the nut on the upper connector and slide it down the chain towards the lower connector. Slide the canopy down the chain towards the lower connector.

Glass

Fixture

Socket

STYLE #3 - Install proper bulb type and wattage before assembling the glass. Remove ball screw from the curved stem. Position glass on lamp with the curved stem being inserted through the hole in the glass. Hand tighten the ball screw to secure the glass in place.

Nut

Feed the wires through the nipple and tighten the upper connector onto the nipple.

STYLE #3

Glass

Nipple

Hole

For Stem

Ball Screw

I f not already done, install proper bulb type and wattage.

Note: If your product does not have a bottom light, your fixture is complete.

Black

Canopy

Upper

Connector

Ground

Wire

White

Nut

Connect the copper wire to ground screw in electrical box. Connect the black wire (or wire marked “SPT-1”) from the fixture to the black wire in the electrical box and connect the white wire from the fixture to the white wire in the electrical box.

Tuck electrical wires into electrical box. Slide canopy into position and tighten in place by sliding upper connector nut into position and tighten.

Note: If required, hook the support arms onto fixture and then into the glass (or hoop).

Note: If required assemble centre body of fixture.

Note: If your product does not have any uplights, please proceed to Step#8.

Note: If required, spread the arms of the fixture out evenly.

Fibre

Washer

Fixture

Glass

Decorative

Cap

Stem

HexNut

Finial

Attach the stem to the fixture.

10.

Position the glass over the stem. Secure the glass in place using the fibre washer, hex nut, decorative cap and finial.

Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville, Ontario, K6V 5V6, Tel: (613) 342-5424, Fax: (613) 342-8437

Hello! I am an AI chatbot specifically trained to assist you with the RICH104B03CH17 Installation Guide. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key features

Safety precautions
Detailed installation steps
Assembly instructions
Wiring guidance
Proper bulb type and wattage
Support arm installation
Glass installation
Center body assembly

Frequently asked questions

Turn off electrical power before starting installation. Do not remove insulation from the fixture. Install the product in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.

Connect the copper wire to the ground screw in the electrical box. Connect the black wire (or wire marked “SPT-1”) from the fixture to the black wire in the electrical box and connect the white wire from the fixture to the white wire in the electrical box.

Refer to the style of assembly that matches your fixture and install proper bulb type and wattage. If your product does not have a bottom light, your fixture is complete.