HDBaseT VGA and Composite Scaler Over CAT5e/6/7

HDBaseT VGA and Composite Scaler Over CAT5e/6/7
Control Your Video
VIDEO WALL VIDEO PROCESSORS
MULTIVIEWERS DIGITAL SIGNAGE
EXTENDERS CONTROL CENTERS
SCALERS WIRELESS
HDBaseT VGA and Composite Scaler Over CAT5e/6/7
Transmitter with LAN Support
Model #: HBT-C6POE-VGA-S
© 2015 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or
warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted
by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and claims any
express or implied warranty, relating to its products are is strictly prohibited.
Product Application & Market Sectors
Corporate
House Of Worship
Military
Residential
Education
Industrial
Medical
Aviation
www.avenview.com
TABLE OF CONTENTS
1.
GETTING STARTED...........................................................................................................................1
1.1 Important Safeguards...............................................................................................................1
1.2 Safety Instructions...................................................................................................................1
1.3 Regulatory Notices Federal Communications Commission (FCC)............................ 2
2.
INTRODuCTION ........................... ..................................................................................................3
3.
FEATURES ....................................... ...................................................................................................3
Package Contents......................................................................................................................4
ation....................................................................................................................4
6.
APPLICATION DIAGRAM ...................................................................................................................5
7.
PANEL DESCRIPTION
...................................................................................................................6
7.1 INPUT PANEL (FRONT PANEL) .................................................................................................6
7.2 INPUT PANEL (REAR PANEL)
.................................................................................................7
7.3 REMOTE CONTROL .....................................................................................................................8
8. RS-232 PIN DEFINITIONS ....................................................................................................................9
9. RS-232 COMMANDS..... .......................................................................................................................10
Pane ...........................................................................................................................................12
11. INPUT RESOLUTION SUPPORT..........................................................................................................14
12. INSTALLATION ....................................................................................................................................15
13. GENERAL TROUBLESHOOTING .......................................................................................................15
14. SPECIFICATIONS .................................................................................................................................16
www.avenview.com
Page
3
1. GETTING STARTED
SECTION 1: GETTING STARTED
1.1 Important Safeguards
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
What the warranty does not cover
•• Any product, on which the serial number has been defaced, modified or removed.
•• Damage, deterioration or malfunction resulting from:
•• Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to
follow instructions supplied with the product.
•• Repair or attempted repair by anyone not authorized by us.
•• Any damage of the product due to shipment.
•• Removal or installation of the product.
•• External causes to the product, such as electric power fluctuation or failure.
•• Use of supplies or parts not meeting our specifications.
•• Normal wear and tear.
•• Any other causes which does not relate to a product defect.
•• Removal, installation, and set-up service charges.
1.2 Safety Instructions
The HBT-C6POE-VGA-S has been tested for conformance to safety regulations and requirements, and has been certified
for international use. However, like all electronic equipments, the HBT-C6POE-VGA-S should be used with care. Read the
following safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.
! Do not dismantle the housing or modify the module.
! Dismantling the housing or modifying the module may result in electrical shock or burn.
! Refer all servicing to qualified service personnel.
! Do not attempt to service this product yourself as opening or removing housing may expose you to dangerous voltage
or other hazards
! Keep the module away from liquids.
! Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on
to the housing, unplug the module immediately.
! Have the module checked by a qualified service engineer before using it again.
! Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
www.avenview.com
Page
1
1.3 Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment.
Warning symbols
Description
ONLY USE THE PROVIDED POWER CABLE OR POWER
ADAPTER SUPPLIED. DO NOT TAMPER WITH THE
ELECTRICAL PARTS. THIS MAY RESULT IN ELECTRICAL
SHOCK OR BURN.
DO NOT TAMPER WITH THE UNIT. DOING SO WILL
VOID THE WARRANTY AND CONTINUED USE OF THE
PRODUCT.
THE VIDEO BOARDS ARE VERY SENSITIVE TO STATIC.
PLEASE ENSURE IF RACK MOUNTED OR INSTALLED ON A
SURFACE, IT SHOULD BE IN A GROUNDED ENVIROMENT.
www.avenview.com
Page
2
2.
Introduction
The HBT-C6POE-VGA-S is an HDBaseT™ Transmitter Scaler that supports PC (VGA) or Composite Video (CV) input. It is
capable of scaling and switching video sources and sending the digital signal over CAT5e/6/7 cable to the Receiver at a distance
of up to 100 meters, along with an external audio input, 2-way IR, RS-232 and bidirectional LAN support. Control is via onpanel buttons or IR remote control and there is an On-screen Display (OSD) providing selection and system information. The
HBT-C6POE-VGA-S provides a full range of output resolutions, from 640 up to 1080p and WUXGA (RB). The bidirectional
Power over Ethernet (PoE) function provides greater flexibility during installations.
3.
FEATURES
• Supports PC/CV scaling to a full range of HDTV or PC resolutions up to 1080p and WUXGA (RB).
• Transmission of uncompressed data over a single CAT5e/6/7 cable up to 100m/328ft.
• 5Play™ convergence: Video and Audio, LAN serving, bidirectional Power over Ethernet (PoE) and Control (IR RS-232 bypass).
• Supports IR, Remote control, RS-232 (bypass) and on-panel controls.
• Provides bidirectional 24V DC power to or receive from compatible PoE Receiver through CAT5e/6/7 cable.
• Supports Ethernet transmission rates up to 100 Mbps.
• Supports NTSC and PAL formats for Composite Video input.
Note:
1. This system was tested with CAT6/23AWG cables, results may vary with cables of different specifications.
2. The PoE function is designed for powering compatible Receiver units only—non-PoE Receivers will need their own power
supply. Receivers from other brands may not be compatible.
3. DO NOT connect the LAN connection to the CAT5e/6/7 port. Doing so may cause a power shutdown and may damage the
device.
www.avenview.com
Page
3
Package Contents
Before you start the installation of the converter, please check the package contents.
1
HBT-C6POE-VGA-S
X1
2
X1
3
USER’S MANUAL
X1
ation
•• Put the product in a level and stable location. If the product falls, it may cause damage or malfunction to components
within the casing.
•• Do not place the product in temperatures under 0˚C or over 50˚C. High humidity may also cause the unit to malfunction.
•• Use the DC power adapter with correct specifications supplied with the unit. If the improper power supply is used, this
may result in malfunction of the unit and may cause fire.
•• Do not twist or pull by force the ends of the HDMI cable. It can cause malfunction.
www.avenview.com
Page
4
6.
ApplICATION DIAGRAM
www.avenview.com
Page
5
7.
pANEl DESCRIpTION
7.1 INPUT PANEL (HBT-C6POE-VGA-S) Front Panel
7
1
2
3
4
5
6
8
9
1. SERVICE: Reserved for manufacturer use only.
2. IR RECEIVER WINDOW: Receives only the IR signal
from the supplied remote control for this device only.
3. PC: Connect to a PC/Laptop source device with a D-Sub
15pin cable.
4. CV: Connect to a composite video source such as a
DVD/Video player.
5. AUDIO: Connect to an analog stereo (L/R) audio
source with a 3.5mm mini-jack cable.
6. MENU: This button enters the On-Screen Display
(OSD) menu.
7. INPUT (–) Button & CV/PC LED: Press the INPUT
(−) button to toggle between CV or PC inputs. When
in CV mode the LED will be lit, off when in PC mode.
8. −/+: Use these buttons to navigate down and up
in the on-screen menu.
9. ENTER: Press to confirm selection.
Note:
Pressing '−' (MINUS) and ENTER simultaneously will immediately
switch the output resolution of the device to 720p60.
Pressing '+' (PLUS) and ENTER simultaneously will immediately switch
the output resolution of the device to XGA (1024×768).
www.avenview.com
Page
6
pANEl DESCRIpTION
7.2 INPUT PANEL (HBT-C6POE-VGA-S) Back Panel
1
2
3
1. POWER LED: This LED will illuminate when the
device is connected to an active power supply.
4
5
6
7
2. DC 24V: Connect the 24 V DC power supply to the
unit and plug the adaptor into an AC outlet. Only one
unit requires powering if both the Transmitter and
Receiver are both PoE compatible.
3. RS-232 IN: Connect to a PC or RS-232 control system
with a D-Sub 9 pin male cable for the transmission of
RS-232 commands.
4. LAN: Connect to an active network for LAN serving.
When any compatible LAN equipped receivers are
connected, this allows the network access (including
internet access if available) to be shared between any
connected LAN equipped receivers. Connect any
Ethernet equipped device e.g. a Smart TV or games
console to the LAN port of a receiver for that device
to share the network/internet access.
5. IR Blaster: Connect the supplied IR Blaster cable for IR
signal transmission. Place the IR Blaster in direct line-ofsight of the equipment to be controlled.
6. IR Extender: Connect the supplied IR Receiver cables
for IR signal reception. Ensure that remote being used is
within the direct lineof-sight of the IR Extender.
7. CAT5e/6/7 OUT: Connect to the Receiver unit with a single CAT5e/6/7 cable for transmission of all data signals.
MODE LED: This LED will illuminate when the power is connected.
LINK LED: This LED will illuminate when connected to a Receiver unit
that is connected with a TV/monitor that is displaying the signal.
www.avenview.com
Page
7
7.3
REMOTE CONTROL
1 INPUT: Press this button to toggle between the CV or PC input.
2 EXIT: Press this button to exit the menu or the current selection in the
on-screen menu.
1
2
3 MENU: Press this button to enter into the OSD menu.
INPUT
EXIT
MENU
3
OK
4 RESET: Press this button to return the device to the factory default settings.
5
4
RESET
5 AUTO ADJUST: Press this button tooptimize the positioning of the picture
AUTO
ADJUST
6
(picture centering) on the screen.
6 OK & ▲▼◄►: Press 'OK' to confirm the selection or use the directional
buttons to navigate the on-screen menus.
7.4 IR Cable Pin Assignment
IR Blaster
1 Power
2 IR Blaster Signal
3 NC
IR Extender
1 IR Signal
2 Power
3 Ground
www.avenview.com
Page
8
8.
RS-232 PIN DEFINITIONS
PIN
DEFINE TX / RX
1
N/C
2
TxD/RxD
3
RxD/TxD
4
NC
5
GND
6
NC
7
NC
8
NC
9
NC
RS-232 SETTINGS
Baud Rate: 9600bps
Data Bit: 8 bits parity:
None
Flow Control: None
Stop Bit: 1
www.avenview.com
Page
9
9.
RS-232 COMMANDS
COMMAND
DESCRIPTION
S SOURCE 1~2
1=VIDEO
2=PC
R SOURCE
Reports the numerical equivalent for the
SOURCE setting (as listed above)
S OUTPUT 0~25
0=Native
12=1600×1200
1=640×480
13=1920×1080
2=800×600
16=1920×1200
3=1024×768
17=480p
5=1360×768
[email protected]
6=1280×720
[email protected]
7=1280×800
[email protected]
8=1280×1024
22=576p
9=1440×900
[email protected]
10=1400×1050
[email protected]
11=1680×1050
[email protected]
R OUTPUT
Reports the numerical equivalent for the
OUTPUT setting (as listed above)
S SIZE 0~6
0=OVERSCAN
4=LETTER BOX
1=FULL
5=UNDER 2
2=BEST FIT
6=UNDER 1
3=PAN SCAN
R SIZE
Reports the numerical equivalent for the SIZE
setting (as listed above)
S CONTRAST 0~60
Sets the numerical value for the CONTRAST
setting (0~60)
R CONTRAST
Reports the numerical value for the CONTRAST
setting (0~60)
S BRIGHTNESS 0~60
Sets the numerical value for the BRIGHTNESS
setting (0~60)
R BRIGHTNESS
Reports the numerical value for the BRIGHTNESS
setting (0~60)
www.avenview.com
Page
10
COMMAND
DESCRIPTION
S HUE 0~60
Sets the numerical value for the HUE setting
((0~60)
R HUE
Reports the numerical value for the HUE setting
(0~60)
S SATURATION 0~60
Sets the numerical value for the SATURATION
setting (0~60)
R SATURATION
Reports the numerical value for the SATURATION
setting (0~60)
S SHARPNESS 0~30
Sets the numerical value for SHARPNESS setting
(0~30)
R SHARPNESS
Reports the numerical value for the SHARPNESS
setting (0~30)
S NR 0~3
0=OFF
2=MIDDLE
1=LOW
3=HIGH
R NR
Reports the numerical equivalent for the NOISE
REDUCTION setting (as listed above)
S AUDIO DELAY 0~3
0=OFF
2=110ms
1=40ms
3=150ms
R AUDIO DELAY
Reports the numerical equivalent for the AUDIO
DELAY setting (as listed above)
S AUDIO MUTE 0/1
0=ON
R AUDIO MUTE
Reports the numerical equivalent for the AUDIO
MUTE setting (as above)
S KEY LOCK 0/1
0=ENABLE
R KEY LOCK
Reports the numeric equivalent for the KEY
LOCK setting (as listed above)
FW
Checks the FIRMWARE version
S RESET 1
Sets the numerical equivalent for the RESET
setting (as left)
1=MUTE
1=DISABLE
Note:
1. RS-232 commands will not execute unless followed by a carriage
return and LF (Line Feed).
2. Commands are not case-sensitive.
3. Resolutions 1~16 are RGB encoded and 17~25 are YUV encoded.
www.avenview.com
Page
11
10. OSD MENU
1ST LAYER
2ND LAYER
3RD LAYER
DISPLAY
OUTPUT
Native
4TH LAYER
640x480 60
800x600 60
1024x768 60
1360x768 60
1280x720 60
1280x800 60
1280x1024 60
1440x900 60
1400x1050 60
1680x1050 60
1600x1200 60
1920x1080 60
1920x1200 60
720x480P 60
1280x720P 60
1920x1080I 60
1920x1080P 60
720x576P 50
1280x720P 50
1920x1080I 50
1920x1080P 50
SIZE
SIZE
OVER SCAN
FULL
ASPECT RATIO
PAN SCAN
LETTER BOX
UNDER 2
UNDER 1
www.avenview.com
Page
12
1ST LAYER
2ND LAYER
3RD LAYER
SIZE
MODE INFO
INFO
4TH LAYER
ON
OFF
PC (PC mode only) AUTO SETUP
NO
YES
H_POSITION
0~60 (30)
V_POSITION
0~60 (30)
PHASE
CLOCK
WXGA/XGA
XGA
WXGA
RESET
NO
YES
COLOR
COLOR
R
G
B
R OFFSET
G OFFSET
B OFFSET
CONTRAST
0~60
BRIGHTNESS
0~60
HUE
0~600~60
SATURATION
0~60
SHARPNESS
0~60
NR.
OFF
LOW
MIDDLE
HIGH
www.avenview.com
Page
13
1ST LAYER
2ND LAYER
3RD LAYER
AUDIO
VOLUME
0~100
DELAY
OFF
4TH LAYER
40ms
110ms
150ms
SOUND
ON
MUTE
SETUP
FACTORY RESET
NO
YES
KEY LOCK
OFF
ON
INFORMATION
INPUT
OUTPUT
REVISION
Note: Items in Bold are the default settings.
11. Input Resolutions Support
INPUT RESOLUTION
CV
PC
NTSC/PAL

-
[email protected]/72/75 Hz
-
[email protected]/60/72/75 Hz
-
[email protected]/70/75 Hz
-
[email protected]/75 Hz
-
[email protected] Hz
-
1280×[email protected] Hz
-
1680×[email protected] Hz (RB)
-
1920×[email protected] Hz
-








www.avenview.com
Page
14
12.
Installation(HBT-C6POE-VGA-S)
To setup Avenview HBT-C6POE-VGA-S please follow these steps for connecting to a device:
1. power off all sources such as media player, set-top box, pC etc;
2. Connect VGA video Source to the VGA INpuT of (HBT-C6POE-VGA-S);
3. Connect HBT-C6POE-VGA-S to HBT-C6POE-R with a CAT5e/6 at the CAT5e/6 OUT;
4. Connect HBT-C6POE-R to TV/Monitor with HDMI Cable;
5. K
6. power on VGA Source and TV/MONITOR;
7. When the Input is connected and turned on the corresponding POWER lED will light.
13. GENERAl TROuBlESHOOTING
PROBLEM
POSSIBLE SOLUTION
•• Check if connection to the source and the display are correct.
•• Ensure that display device supports resolution from 640 up to 1080p.
NO IMAGE
•• please use the supplied power supply-24V DC
•• Check LI3RZHUlED light DQGMode / Link lights on the CAT5E/6 connector
MODE LED: This LED will illuminate when the power is connected.
LINK LED: This LED will illuminate when connected to a Receiver unit that is connected
with a TV/monitor that is displaying the video and audio signal.
• Check INPUT (–) Button & CV/PC LED: Press the INPUT (−) button to toggle
between CV or PC inputs. When in CV mode the LED will be on, LED off
when in PC mode. (Section 3 panel Description)
please use the supplied power supply-24V DC
www.avenview.com
Page
15
14. Specifications
Item
UNITS
UNIT DESCRIPTION
OUTPUT BANDWIDTH
Description
HBT-C6POE-VGA-S
HDBaseT™ Transmitter Scaler
300MHz / 10.2Gbps
CV RESOLUTION SUPPORT
VGA RESOLUTION SUPPORT
CAT5 RESOLUTION SUPPORT
NTSC/PAL
VGA~WUXGA (RB)
4HD: Up to [email protected] Hz / PC: Up to WUXGA (RB)
IR FREQUENCY
30~50 kHz
1×Composite Video, 1×VGA, 1×3.5mm, Mini-jack (L/R),
INPUT
1×RS-232, 1×LAN,
1×IR Extender
OUTPUT
DIMENSIONS (WxDxH)
1×CAT5e/6/7, 1×IR Blaster
7.9" x 5.7" x 1.2" (Jacks Included)
NET WEIGHT
POWER SUPPLY
1.33lbs
24V/2.7A DC / 110-240V
POWER CONSUMPTION
ESD PROTECTION
16W
Human body model - ±15kV (air gap discharge) &±8kV (contact discharge)
Environmental
Operating Temperature
Storage Temperature
Relative Humidity
32˚ ~ 104˚F (0˚ to 40˚C)
-4˚ ~ 140˚F (-20˚ ~ 60˚C)
20~90% RH (non-condensing)
www.avenview.com
Page
16
Avenview Warranty Certificate
AVENVIEW CORP. (“Avenview”) warrants Avenview-branded product(s) contained in the original packaging against defects in materials and workmanship when used
normally in accordance with Avenview's enclosed manual guidelines for a period of THREE (3) YEARS from the date of original retail purchase - Warranty Period. Avenview’s
published guidelines include but are not limited to information contained in technical specifications, user manuals and service communications.
LABOR: During the Warranty Period of THREE (3) YEARS, Avenview will repair or replace the product(s) at no cost using new or used parts equivalent to novel performance
and reliability if the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Labor applicable to product(s) after Warranty Period. For labor costs,
please contact [email protected]
PARTS: During the Warranty Period of of THREE (3) YEARS, Avenview will supply new or rebuilt replacements in exchange for defective parts of the product(s) at no cost if
the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Parts applicable to product(s) after Warranty Period. For part(s) costs, please contact
[email protected]
To obtain Warranty: (a) proof of purchase in the form of a bill of sale or receipted invoice reflecting that the registered product(s) is within warranty period must be presented
to obtain warranty service; (b) product(s) must be registered at time of purchase. Failure to do so will result in applicable parts and labor charges. Returning product(s) must
be shipped in Avenview’s original packaging or in packaging pertaining equal degree of protection to Avenview’s. Both Avenview and purchaser are responsible for freight
charges and brokerages when shipping the product(s) to the receiver.
NOT COVERED BY THIS WARRANTY
This warranty does not apply to any non-Avenview branded product(s); non-registered Avenview product(s). This warranty does not apply: (a) to cosmetic damage, including
but not limited to scratches, dents and broken cords; (b) to damage caused by use with another product; (c) to damage caused by accident, abuse, misuse, liquid contact, fire,
earthquake or other external cause; (d) to damage caused by operating the Avenview product(s) outside Avenview’s manuals or guidelines; (e) to damage caused by service
performed by anyone who is not a representative of Avenview or an Avenview authorized personnel; (f) to defects caused by normal wear and tear or otherwise due to the
normal aging of the Avenview product(s), or (g) if any serial number has been removed or defaced from the Avenview product(s).
AVENVIEW IS NOT LIABLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR
CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOSS OF USE; LOSS OF REVENUE; LOSS OF ACTUAL OR
ANTICIPATED PROFITS (INCLUDING LOSS OF PROFITS ON CONTRACTS); LOSS OF THE USE OF MONEY; LOSS OF ANTICIPATED SAVINGS; LOSS OF BUSINESS;
LOSS OF OPPORTUNITY; LOSS OF GOODWILL; LOSS OF REPUTATION; LOSS OF, DAMAGE TO, COMPROMISE OR CORRUPTION OF DATA; OR ANY INDIRECT
OR CONSEQUENTIAL LOSS OR DAMAGE REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER.
Some states do not allow the inclusion or limitation of incidental or consequential damages, or allow limitations on duration implements of the Warranty Period; therefore the above limitations or
exclusions may not be applicable to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
275 Woodward Avenue, Kenmore, NY 14217
1.866.508.0269
www.avenview.com
Control Your Video
TECHNICAL SUPPORT
Avenview USA
Avenview Head Office
275 Woodward Avenue
Kenmore, NY 14217
Phone: 1.716.218.4100
Fax: 1.866.387.8764
Email: [email protected]
Avenview Canada
Avenview Sales
151 Esna Park Drive, Units 11 & 12
Markham, ON, L3R 3B1
Phone: 1.905.907.0525
Fax: 1.866.387.8764
Email: [email protected]
Avenview Europe
Avenview Europe
Demkaweg 11
3555 HW Utrecht
Netherlands
Phone: +31(0)85.2100.613
Email: [email protected]
Avenview Hong Kong
Unit 8, 6/F., Kwai Cheong Centre,
50 Kwai Cheong Road,
Kwai Chung, N.T.
Hong Kong
Phone: 852.3575.9585
Email: [email protected]
Disclaimer
While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of
Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this
documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequential damages
in connection with the furnishing, performance, or use of the Avenview hardware, software, or other products and documentation provided herein.
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability, function or design.
With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties regarding such products, including but
not limited to, the implied warranties of merchantability, fitness for a particular purpose, and non-infringement.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement