OPERATING INSTRUCTIONS DENTAL UNIT AND CHAIR

OPERATING INSTRUCTIONS DENTAL UNIT AND CHAIR
DENTAL UNIT AND CHAIR
OPERATING INSTRUCTIONS
IMPORTANT
This manual provides operating instructions for CP-ONE.
The instructions contained in this booklet should be thoroughly read and
understood before operating the unit and chair.
File this manual and refer back to it for future maintenance.
0197
TABLE OF CONTENTS
1. Overall view and major components----------------------------1
2. Dimensions and specifications
2-1. Dimensions---------------------------------------------------2
2-2. Specifications-------------------------------------------------2
3. Operating instructions
3-1. Control panel ------------------------------------------------3
3-2. Master switch-------------------------------------------------4
3-3. Chair operating instructions--------------------------------4
3-4. Control panel operating instructions ---------------------6
3-5. Unit supplement functions ---------------------------------8
3-6. Doctor table operating instructions------------------------10
3-7. Cuspidor unit operating instructions ---------------------11
3-8. Foot controller------------------------------------------------12
3-9. Assistant instrument holder---------------------------------12
4. Care and maintenance
4-1. Care and maintenance for chair ---------------------------13
4-2. Care and maintenance for unit ----------------------------13
5. Electromagnetic Compatibility (EMC)------------------------16
6. List of compatible handpieces ----------------------------------19
Intended Use of the Product
This product is an active therapeutic device intended for the exclusive use for diagnoses,
treatments and relative procedures of dentistry.
The product must be operated or handled by the qualified dentists or by dental staffs under
the supervision of the dentist.
Such dentists or dental staffs should instruct and/or assist the patients to approach to and
leave from the product.
Patients should not be allowed to operate or handle the product unless he/she is so instructed.
The product is supplied together with the handpieces like electric micromotor, air turbine
and/or motor, scaler and so on.
Environmental Requirements
Ambient Temperature
Operating +5℃ - +40℃
Atmospherical Pressure
600 hPa - 1060 hPa
Humidity
10 % - 80%
Storage -10℃ - +50℃
Compatibility of Handpieces
Use the compatible handpieces as shown on the attached list for this unit. (List of compatible
handpieces).
Important Notes
In case of the troubles, please contat Takara Belmont offices or your dealers.
Do not disassemble or attempt to repair.
Disassembly, repair or modifications shoud only be done by a qualified repair technician.
Attempts at disassembly, repair or modifications may lead to abnormal operation and accidents.
In case of disposal of equipment
When disposing the chair, appropriately dispose complying with all current applicable regulations and
local codes.
In EU area, EU directive 2002/96/EC on waste electrical and electronic equipment (WEEE) is applied
on this product. In this directive, environment conscious recycling/abandonment is obligated.
SYMBOLS
Chair last position
Chair auto return
Chair preset1
Chair preset2
Chair control
To raise the chair
To Recline
the backrest
To lower the chair
To raise
the backrest
Headrest
manual control
Film viewer on/off
Handpiece Setting
Fiber optic
handpiece light
on//off
Handpiece coolant
spray on/off
Micro motor
Forward/Reverse
select
Syringe
Function
Store
Bowl flush
Cupfiller
Timer
Dental light on/off
Air
Type B
Applied Parts
Non-ionizing
radiation
Manufacturer
Date of manufacture
Caution
It means “caution,
warnings, or
possibility to
danger”.
㹌
Water
㻨㻦
Authorized
representative in
the European
community
㻵㻨㻳
Separate
collection for
electrical and
electronic
equipment
㸶
Minus
Plus
1. OVERALL VIEW AND MAJOR COMPONENTS
2
1
3
20
21 22
14
4
11
5
6
15
8
10
14
9
7
23
16
12
17
19
18
27
13
25 26
24
Cuspidor unit front left
Fig.1-1-1 Overall view and major parts
1. Dental light (io5000)
16. Assistant control panel
2. Dental light horizontal arm
17. Power headrest control panel
3. Dental light pole
18. Chair control panel
4. Power headrest
19. Foot control (SE Type)
5. Backrest
6. Seat
7. Footrest
8. Armrest
9. Doctor table unit
10. Main control panel
11. Control housing
12. Handpiece holder (Place type)
20. Cuspidor bowl
21. Cupfiller nozzle
22. Bowl flush nozzle
23. Assistant holder arm
24. J-Box cover
25. Stop valve for water
26. Pressure gauge
27. Handpieces
(Micromotor, Air Turbine/Motor,
13. Doctor table arm
Scaler and etc.) Manufacturers recommend
14. Cuspidor unit
to use the handpieces with CE markings
15. Assistant holder
-1-
2. DIMENSIONS AND SPECIFICATIONS
2-1. Dimensions
-mm-
90
1730
370
486
90
440
648
120
24°
392
504
613
180°
40°
440
228
40°
508
138
150
398
1645
40
40
570
32
80
5
720
1050~1635
805
0
20
40
15
220
400~800
752
75
2000
570
220
320
600
903
2-2. Specifications
Seat initial height------------------------ 400mm
Seat lifting stroke----------------------- 400mm
Backrest movement--------------------- 0˚ ~ 80˚ above horizontal
Auto movements------------------------ 2 Preset, 1 Last position memory and 1 Auto return
Control voltage-------------------------- DC12V
Power consumption--------------------- 230V 50Hz 3.1A
Dental light------------------------------ io5000 (520 Type)
Net weight------------------------------- Chair
170 kg
Unit
90 kg
Maximum Load------------------------- 135 kg
Service Life------------------------------ 10 years
-2-
3. OPERATING INSTRUCTIONS
3-1. Control Panel
Control panels locations and functions are shown in Fig.3-1-1.
Doctor unit control panel
Assistant control panel
4
3
2
1
5
6
8
7 9 11 10 15 16 17 18 19 20
19
20
23
5
13 12
14 21 22
Power headrest control panel
24
Fig. 3-1-1
1. Power indicator
2. Lock indicator
3. Film viewer switch (Dental size)
4. Film viewer
5. Chair auto mode switch
6. Chair manual control switch
7. Handpiece coolant water switch
8. Handpiece coolant air indicator
for micro motor
9. Handpiece coolant water indicator
for micro motor
10. Light pack switch
11. Light pack indicator
12. Micro motor direction control switch
13. Micro motor direction indicator counter-clockwise
14. Micro motor direction indicator clockwise
15. Function indicator
16. Function switch
17. Store switch
18. Timer switch
19. Dental light switch
20. Cupfiller switch
21. Decrease switch
22. Increase switch
23. Bowl flush switch
24. Power headrest switch
-3-
3-2. Master Switch
Turn on the master switch located on the facing right side table (Refer to Fig.3-2-1),
the power indicator on the main control panel illuminates in green.
Note : CP mark in function indicator will be turned off if the unit is not operated for 30
seconds. It will appeare again when the unit is re-operated.
Master switch
Function indicator
MAIN
1 2
3
4
I
○
ON
OFF
Fig.3-2-1
CAUTION
Turn off the master switch after daily operation or in long term interval.
3-3. Chair Operating Instructions
CAUTION
Before operating the chair, confirm safety for the patient and the operator
3-3-1. Chair manual control switch
1) Seat lifting
Keep depressing
switch of the chair manual control switch until the seat is lifted up
to the desired position.
2) Seat lowering
Keep depressing
switch of the chair manual control switch until the seat is lowered
to the desired position.
3) Backrest reclining
Keep depressing
switch of the chair manual control switch until the backrest is
reclined to the desired position.
4) Backrest raising
Keep depressing
switch of the chair manual control switch until the backrest is
rased to the desired position.
5) Headrest extension
Keep depressing
switch of the power headrest control panel until the headrest
is lifted up to the desired position.
6) Headrest lowering
Keep depressing
switch of the power headrest control panel until the headrest
is lowered to the desired position.
-4-
7) Headrest forward
Keep depressing
switch of the power headrest control panel until the headrest
Keep depressing
switch of the power headrest control panel until the headrest
is raised up to the desired position.
8) Headrest retract
is retracted to the desired position.
3-3-2. Chair auto mode control switch
1) Preset Control
CP-ONE chair has two preset positions.
Momentary depress 1 button of the chair auto mode switch, the chair will move to the
preset-1 position automatically. ( Preset-2 is operated by 2 button.)
2) Preset position adjustment
Two preset position can be set.
Procedure 1.
1. Set seat and backrest in the desired position by manual control switches.
2. Keep depressing store button on chair preset panel until buzzer sounds Pi-,Pi-,Pi-.
3. While buzzer is sounding, press 1 button on doctor table or assistant side control panel
so that the position is memorized to preset 1, then the buzzer sound ceases.
4. Preset 2 is memorized by pressing 2 button as following 1 to 3.
Procedure 2.
1. Set seat and backrest in the desired position by manual control switches.
2. Keep depressing 1 button on doctor table or assistant side control panel until buzzer
sounds so that the position is memorized to Preset 1, then the buzzer sound ceases.
3. PRESET 2 is memorized by pressing 2 button as following 1 to 2.
3) Auto return
Momentary depress 0 button of the chair auto mode switch, the chair will move to the
initial position automatically.
(The seat is fully lowered and backrest is upright position.)
4) Last Position Memory
Momentary depress
button of the chair auto mode switch at chair treatment position,
Momentarily depress
button again, the backrest and seat will return to the previous
the backrest and seat will move to the mouth rinsing position automatically.
treatment position automatically.
5) Emergency Stop
During automatic procedure (preset, auto return and last position memory), momentarily
pressing any chair control switch will cancel the automatic movement immediately.
6) Safety lock
During the handpiece is running, the safety lock indicator illuminates in red and
all chair control switches are inactivated.
-5-
3-4. Control Panel Operating Instructions
3-4-1. Dental size film viewer switch (Fig.3-4-1)
Momentarily press the film viewer switch, film viewer turns on
until film viewer switch is pressed again.
3-4-2. Handpiece coolant water switch (Fig.3-4-2)
When both indicators are illuminated, coolant water comes out of the
handpiece when it is taken out of its holder and foot controller pedal is
depressed.
Momentarily pressing the handpiece coolant water switch will stop
spray water.
3-4-3. Light pack optional switch (Fig.3-4-3)
Momentarily press the light pack switch, the indicator illuminates
and the handpiece light turns on until the light pack switch is
pressed again.
3-4-4. Micromotor optional direction control switch (Fig.3-4-4)
Rotational direction of the micromotor can be changed by
momentarily pressing the micromotor direction control switch, and
rotational direction is indicated by the indicator.
Note ; Do not change rotational direction during micromotor
is running.
3-4-5..Function switch (Fig.3-4-5) / Store Switch (Fig.3-4-6)
This unit provides supplement functions (flushout system, control panel
switching sound on/off, fiber optic handpiece illumination timing, timer,
micromotor control and bowl flush timing). Supplement function are
selected by the function switch and set by the store switch.
Fig. 3-4-1
Fig. 3-4-2
Fig. 3-4-3
Fig. 3-4-4
Fig. 3-4-5
Fig. 3-4-6
3-4-6. Dental light switch (Fig.3-4-7)
Momentarily press the dental light switch, the dental light turns on
until the dental light switch is pressed again.
-6-
Fig. 3-4-7
3-4-7. Timer switch(Fig.3-4-8) / Time setting switches (Fig.3-4-9/Fig.3-4-10)
Timer can be set maximum 90 mins. 50 secs. in 10 secs. segment.
Momentarily press the timer switch, and set the time by pressing
switch and
switch.
Minimum setting time by
Minimum setting time by
switch is 10 seconds.
Fig.3-4-8
switch is 1 minute.
The setting time is indicated on the function indicator.
Example : Setting time 3 mins. 30 secs. is indicated as T s 03 : 30
in the function indicator.
Momentarily press the timer switch to start timer. The end of setting
time is informed by electronic sounds.
3-4-8. Cupfiller switch (Fig.3-4-11)
Momentarily press the cupfiller switch, cupfiller water comes out from
the cupfiller nozzle for about 6.5 seconds and stops automatically.
During the cupfilling, pressing the cupfiller switch stops filling.
Fig.3-4-9
Fig.3-4-10
Fig.3-4-11
Note : Do not press the cupfiller switch when a cup is not on the
cupfiller base.
3-4-9. Bowl flush switch (Fig.3-4-12)
Momentarily press the bowl flush switch, bowl flush water flushes for
about 6 seconds from the bowl flush nozzle and stops automatically.
During the bowl flushing, pressing the bowl flush switch stops bowl
flushing.
Keep pressing the bowl flush switch for about two seconds, water
flushes continuaously until the bowl flush switch is pressed again.
-7-
Fig.3-4-12
3-5. Unit Supplement Functions
3-5-1. Flush out system
The CP-ONE is equipped with two types of flush out system.
Short time flush out is for cleaning handpiece water lines.
Long time flush out is for handpiece water lines, bowl flush water line
and cupfiller water line.
1) Short time flush out F +
Momentarily press the function switch and momentarily press the
switch.
Pick up the handpieces from holder and set them in cuspidor bowl.
Momentarily pressing the foot controller starts short time flush out.
Water comes out from the handpiece and stops automatically in about
40 seconds.
During flush out, momentarily pressing the any one of F ,
foot controller will cancel flushout immediatly.
,
Function switch
or
2) Long time flush out F +
Momentarily press the function switch and momentarily press the
increase switch.
Pick up the handpieces from holder and set them in cuspidor bowl.
Momentarily pressing the foot controller starts long time flush out.
Flush out starts and cupfiller and bowl flush after another and stops
automatically in about 10 minute.
During flush out, momentarily pressing the any one of F ,
foot controller will cancel flushout immediatly.
,
or
3-5-2. Control panel switching sound on/off
Pressing a switch on the control panel makes an electronic sound. This
sound can be eliminated as follows;
Momentarily press the function switch twice and momentarily press
switch.
To return to original setting.
Momentarily press the function switch twice and momentarily press
switch.
-8-
Function switch
3-5-3. Fiber optic handpiece lighting mode
In case that fiber optic handpiece is installed, fiber optic turns on
when the handpiece is taken out of the holder, and turns off when
the handpiece is returned to the holder.
This could be changed as fiber optic on when the handpiece is taken
out of holder and drive air pedal of foot control is activated.
Momentarily press the function switch three times and press
switch.
Momentarily press the function switch three times and press
switch.
To return to original setting.
3-5-4. Electronic sound for timer
Electronic sound for timer can be changed.
Momentarily press the function switch four times.
Momentarily press one of 0 , 1 , 2 ,
electronic sound is to be memorized.
Function switch
switchs then the new
3-5-5. a. Micromotor maximum speed setting for PL970
The maximum rotation speed of the micromotor can be selected
3 steps (10000,20000,40000rpm). This function can be changed to 5
steps (5000,10000,20000,30000,40000rpm) as follows:
Momentarily press the function switch five times and press
switch.
Momentarily press the function switch five times and press
switch.
To return to original setting.
b. Micromotor maximum speed setting for PLMPPE021
The maximum rotation speed of the micromotor can be selected
3 steps (60 - 500, 1000 - 20000, 1000 - 40000rpm).
This function can be changed to 5steps (60 - 500, 60 - 1000,
1000 - 20000, 1000 - 30000, 1000 - 40000rpm) as follows:
Momentarily press the function switch five times and press
switch.
Momentarily press the function switch five times and press
switch.
To return to original setting.
3-5-6. Micromotor spray mode
In case that micromotor is installed, coolant air and water can be
operated independentry as follows;
Momentarily press the function switch six times and press
switch.
Momentarily press the function switch six times and press
switch.
To return to original setting.
-9-
Function switch
1
2
0
LP
Function switch
Function switch
Function switch
3-5-7. Cupfiller and bowl flush
Cupfiller and bowl flush are set to operate together (when cupfiller
switch is activated, bowl flush also starts).
To make these operate independentry.
Function switch
Momentarily press the function switch seven times and press
switch.
Momentarily press the function switch seven times and press
switch.
To return to original setting.
3-6. Doctor table operating instructions
MAIN
W A
A
1 2
3
4
I
○
Increase
Handpiece coolant water control knobs
Handpiece coolant air control knob
Syringe flow control knobs
Declease
Knob
3-6-1. Handpiece coolant water control
The handpiece coolant water control knobs are located at the front of doctor table bottom.
Each handpiece coolant water knob is lined up from the facing left.
The handpiece coolant water can be controlled independentry.
3-6-2. Handpiece coolant air control
The handpiece coolant air control knobs are located at the front of doctor table bottom.
The handpiece coolant air for all handpieces is controlled by an air control knob.
3-6-3. Syringe flow control knobs
Syringe flow control knobs for doctor are located at the right side of doctor unit bottom.
The syringe flow control knobs adjust syringe air and water flow.
The yellow capped knob is the air flow control knob, the blue capped knob is the water
control knob.
3-6-4. Table height adjustment
Hold the doctor table and slightly lift it up,
stopper ring will come up on upper swing
arm.
Slide up or down the stopper ring to
appropriate groove on upper swing arm.
Lower the doctor table to fix it at that height.
Upper swing arm
Stopper ring
Control housing
CAUTION
CAUTION
Turn off the master switch before
Handpieces
Refer to handpiece manufacturers operating instructions.
-10-
adjusting the table height.
3-7. Cuspidor unit operating instruction
3-7-1. Sensor cupfiller
Place a cup on the cupfiller base, water comes out from the cupfiller nozzle to fill the cup,
and stops automatically.
During filling the cup, momentarily pressing the cupfiller switch will stop filling.
Note : Use suitable disposable paper cup only.
Cupfiller nozzle
Sensor
Cup
Bowl flush nozzle
Cupfiller switch
Cupfiller base
Cuspidor bowl
3-7-2. Assistant panel
Assistant’s syringe air and water flow control knobs, service air and water outlet, service
water control knob, water heater switch, and mode selection switch for dental light are
located on the cuspidor unit control panel.
SENS.
MANU.
I I
Water heater switch
Service water outlet
control knob
Service water outlet
Mode selection switch
I
A
Syringe flow control knob
Increase
Decrease
W
Service air outlet
Knob
1) Syringe flow control knobs
The syringe flow control knobs adjust syringe air and water flow.
The yellow capped knob is the air flow control knob, the blue capped knob is the water
control knob.
2) Service water outlet
The service water outlet provides quick- connect water.
The water volume of service outlet can be adjusted by the service water outlet control
knob.
-11-
3) Service air outlet
The service air outlet provides quick- connect air.
Note : Turning a control knob counterclockwise increases flow volume and turning
clockwise decreases.
4) Water heater switch
Turn on (Press “1” side) the water heater switch, cupfiller water will be warmed up.
5) Mode selection switch for Dental light io5000
Dental light can be operated (on/off) either by the sensor switch located on the light
head, or by the doctor unit control panel and assistant control panel.
To operate by sensor switch : Set the switch lever to right(sens.).
To operate by control panel : Set the switch lever to left(manu.).
3-8. Foot controller
Pick up a handpiece from handpiece holder and depress the foot controller pedal,
the handpiece starts running and coolant water comes out from the handpiece.
Handpiece rotation speed can be controlled by the pressure of depressing the foot
controller pedal. During air handpiece is running, the drive air pressure is indicated in
the handpiece pressure gauge. Handpiece pressure gauge is located on the right side of
doctor table.
Note : Handpiece coolant water on/off can be
Pedal
controlled by the handpiece coolant
water switch on the doctor unit control
panel.
1) Safety lock system
During a handpiece is running, the lock indicator illuminates on the doctor unit control
panel and all movements of chair are locked for safety.
2) First priority system
If a handpiece is taken from the handpiece holder, any other handpiece will not operate
for safety.
3-9. Assistant instrument holder
Pick up a instrument(saliva ejector or vacuum handpiece) from the assistant holder,
and it starts working automatically.
Note : In central vacuum system, the vacuum handpiece will keep working for about
eight seconds after it is returned to its holder to clean the inside of vacuum hose.
-12-
4.CARE AND MAINTENANCE
CAUTION
Turn off the master switch at the initial position after daily operation or in long
term interval.
Turn off the main water valve after daily operation or in long term interval.
4-1. Care and maintenance for chair
4-1-1. Other than cleaning, no scheduled maintenance of chair is required.
CAUTION
Do not drench the chair for cleaning.
Do not use polishing powder, solvents, strong disinfectant and hot water for cleaning.
After cleaning, wipe with a dry soft cloth and keep dry.
Upholstery can be cleaned with a neutral detergent.
Paint parts, metal parts and plastic parts can be cleaned with DURR FD333 cleaner
( or equivalent).
Do not drench the chair and unit. Wipe all surfaces dry after cleaning.
4-2. Care and maintenance for unit
4-2-1. Cleaning unit
CAUTION
Do not drench the unit for cleaning.
Do not use polishing powder, solvents, strong disinfectant and hot water for cleaning
After cleaning, wipe with a dry soft cloth and keep dry.
All surfaces can be cleaned with DURR FD333 cleaner.
Spray the cleaner (DURR FD333) on cloth and wipe the surfaces with the cloth.
Do not drench the chair and unit. Wipe all surfaces dry after cleaning.
4-2-2. Cuspidor bowl
Take out the drain cap and the basket
strainer from the cuspidor bowl.
Unscrew the cuspidor bowl and remove it.
4-2-3. Solid collector
Pull out the solid collector with filter and
clean it.
-13-
Solid collector
Filter
Drain cap
Basket strainer
Cuspidor bowl
Cuspidor top
4-2-4 Handpiece
1. Vacuum Handpiece and Saliva Ejector
A. Pull and remove the top parts of each handpiece and
clean strainer.
B. After daily operation, run two cup of clean water through
handpieces to clean inside.
Sterilization
Vacuum Tip
Vacuum Tip/Saliva Ejector Tip/Vacuum Cap/Vacuum Handpice
Body/Saliva Ejector Handpiece Body can be sterilized with
Saliva Ejector
Tip
Vacuum Cap
autoclave. Vacuum handpiece body and saliva ejector body
must be assembled before autoclaving.
A. Wash off dirt of the handpiece with natural detergent.
Vacuum
Handpiece
Body
Vacuum
Hose
Saliva Ejector
Handpiece
Body
Saliva Ejector
Hose
Fig.4-3 Vacuum and Saliva Ejector
Handpiece
B. Rinse the handpiece with tap water
C. Insert the handpiece in a sterilization pouch and seal it.
D. Autoclave for 20 min. at 121℃
Note: The slide knob can be autoclaved 100 times and is an
expendable supply.
CAUTION
• Skip dry cycle.
Note: After cleaning the handpieces, apply a white vaseline lightly
on the upper parts (O-Ring) and screws parts for long life.
Keep the handpieces in a clean place
2. Micro Motor / Turbine / Scaler
Sterilize the handpiece according to manufacturer’s operating manual.
3. Belmont 77 Syringe
Remove the nozzle from syringe and clean it.
Sterilization
The nozzle can be sterilized with autoclave.
Nozzle
A. Wash off dirt of the nozzle with natural detergent.
B. Rinse the nozzle with tap water.
C. Insert the nozzle in a sterilization pouch and seal it.
D. Autoclave for 20 min. at 121℃
CAUTION
• Skip dry cycle.
Note: Keep the syringes in a clean place
4. Tubing and Hose
It is recommended that Durr FD333 be used to clean
the exterior parts of tubing and hose.
-14-
Belmont 77 syringe
4-2-5. Main water valve
Main water valve is located on the utility parts of
cuspidor unit. Turn off the main water valve after
daily operation or in long term interval.
Main water valve
4-2-6. Oil mist separator
Handpiece oil mist separator is located under the
doctor table. Once a week open the oil mist
separator and clean the oil mist filter.
Oil mist filter
Oil mist separator body
Open
Close
4-2-7. Drain valve for air filter
The drain valve is located on the utility parts of
cuspidor unit. Once a week open the drain valve
and drain off water from the air filter.
Drain valve
-15
5.ELECTROMAGNETIC COMPATIBILITY
Medical electrical equipment needs special precautions regarding EMC and needs to be installed and
put into service according to the EMC information provided in this manual.
Portable and mobile RF communications equipment can affect medical electrical equipment.
The equipment or system should not be used adjacent to or stacked with other equipment. If adjacent
or stacked use is necessary, the equipment or system should be observed to verify normal operation in
the configuration in which it will be used.
Guidance and manufacture’s declaration - electromagnetic emissions
The CP-One is intended for use in the electromagnetic environment specified below. The customer or the user of
the CP-One should assure that it is used in such an environment.
Emissions test
Compliance
Electromagnetic environment - guidance
RF emissions
The CP-One uses RF energy only for its internal
CISPR 11
function. Therefore, its RF emissions are very low
Group 1
and are not likely to cause any interference in nearby
electronic equipment.
RF emissions
The CP-One is suitable for use in all establishments,
Class B
CISPR 11
including domestic establishments and those directly
Harmonic emissions
connected to the public low-voltage power supply
Class A
IEC 61000-3-2
network that supplies buildings used for domestic
Voltage fluctuations/
purposes.
Flicker emissions
Complies
IEC 61000-3-3
Guidance and manufacture’s declaration - electromagnetic immunity
The CP-One is intended for use in the electromagnetic environment specified below. The customer or the user of
the CP-One should assure that it is used in such an environment.
IEC 60601
Electromagnetic environment Immunity test
Compliance level
test level
guidance
Electrostatic
±6 kV contact
±6 kV contact
Floors should be wood, concrete
discharge (ESD)
±8 kV air
±8 kV air
or ceramic file. If floors are
IEC 61000-4-2
covered with synthetic material,
the relative humidity should be
at least 30%.
Electrical fast
±2 kV for power
±2 kV for power
Mains power quality should be
transient/burst
supply lines
supply lines
that of a typical commercial or
IEC 61000-4-4
±1 kV for input/output
±1 kV for input/output
hospital environment.
lines
lines
Surge
±1 kV differential mode
±1 kV differential mode
Mains power quality should be
IEC 61000-4-5
±2 kV common mode
±2 kV common mode
that of a typical commercial or
hospital environment.
Voltage dips, short
<5% UT
<5% UT
Mains power quality should be
interruptions and
(>95% dip in UT)
(>95% dip in UT)
that of a typical commercial or
voltage variations
for 0.5 cycle
for 0.5 cycle
hospital environment. If the user
on power supply
40% UT
40% UT
of the CP-One requires continued
input lines
(60% dip in UT)
(60% dip in UT)
operation during power mains
IEC 61000-4-11
for 5 cycle
for 5 cycle
interruptions, it is recommended
70% UT
70% UT
that the CP-One be powered
(30% dip in UT)
(30% dip in UT)
from an uninterruptible power
for 25cycle
for 25cycle
supply or a battery.
<5% UT
<5% UT
(>95% dip in UT)
(>95% dip in UT)
for 5 s
for 5 s
Power frequency
3 A/m
3 A/m
Power frequency magnetic fields
(50/60 Hz)
should be at levels characteristic
magnetic field
of a typical location in a
IEC 61000-4-8
typical commercial or hospital
environment.
NOTE UT is the a.c. mains voltage prior to applications of the test level.
-16-
Guidance and manufacture’s declaration - electromagnetic immunity
The CP-One is intended for use in the electromagnetic environment specified below. The customer or the user of the
CP-One should assure that it is used in such an environment.
Compliance
Immunity test
IEC 60601 test level
Electromagnetic environment - guidance
level
Portable and mobile RF communications equipment should be used no closer to any part of
the CP-One, including cables, than the recommended separation distance calculated from the
equation applications to the Frequency of the
transmitter.
Conducted RF
IEC 61000-4-6
3 Vrms
150 kHz to 80 MHz
outside ISM bandsa
3 Vrms
Radiated RF
IEC 61000-4-3
3V/m
80 MHz to 2.5 GHz
3 V/m
Recommended separation distance
d = 1.2√P
d = 1.2√P 80 MHz to 800 MHz
d = 2.3√P 800 MHz to 2.5 GHz
Where P is the maximum output power rating
of the transmitter in watts (W) according
to the transmitter manufacturer and d is the
recommended separation distance in metres (m).
Field strengths from fixed RF transmitters, as
determined by an electromagnetic site survey,a
should be less than the compliance level in each
frequency range.b
Interference may occur in the vicinity of equipment marked with the following symbol:
NOTE 1 At 80 MHz and 800MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by adsorption
and reflection from structures, objects and people.
a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land
mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically
with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site
survey should be considered. If the measured field strength in the location in which the CP-One is used exceeds
the applicable RF compliance level above, the CP-One should be observed to verify normal operation. If
abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the
CP-One.
b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3V/m.
Essential performance (purpose of IMMUNITY testing)
Unless operated by the switches for chair control, the chair section of the CP-ONE does not make any
movements, except for sounding a buzzer and switching on/off the indicator.
-17-
Recommended separation distances between
Portable and mobile RF communications equipment and the CP-One
The CP-One is intended for use in an electromagnetic environment in which radiated RF disturbances are
controlled. The customer or the user of the CP-One can help prevent electromagnetic interference by maintaining a
minimum distance between portable and mobile RF communications equipment (transmitters) and the CP-One as
recommended below, according to the maximum output power of the communications equipment.
Separation distance according to frequency of transmitter
Rated maximum output power
m
of transmitter
150 kHz to 80 MHz
80 MHz to 800 MHz
800 MHz to 2.5 GHz
W
d = 1.2√P
d = 1.2√P
d = 2.3√P
0.01
0.12
0.12
0.23
0.1
0.38
0.38
0.73
1
1.2
1.2
2.3
10
3.8
3.8
7.3
100
12
12
23
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in
metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the
maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.
NOTE 1 At 80 MHz and 800MHz, the separation distance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by adsorption
and reflection from structures, objects and people.
-18-
6. LIST OF COMPATIBLE HANDPIECES
DESCRIPTION
Syringe
LUZZANI(3-way ) Minilight w/Light
LUZZANI(6-way ) Minilight w/Light
DCI(3-way )
Turbine
BIEN AIR BORA S36L / UNIFIX with LIGHT
NSK Ti-Max X
Air motor
BIEN AIR Aquilon 830 / UNIFIX with LIGHT /PM1132
NSK EX-203 / EX-6
Micromotor
BIEN AIR MC3LK / PLMP021PCB. / PM1132
BIEN AIR MC3LK / PL970 PCB. / PM1132
BIEN AIR ISOLITE(LK 40 IR E) / PLMP021PCB. / PM1132
BIEN AIR ISOLITE(LK 40 IR E) / PL970. / PM1132
NSK TIM-40J / DA-290N PCB. / EX-6
Scaler
SATELEC SP4055 w/Light
EMS SCALER
NSK VARIOS VA 150 LUX(w/light)
-19-
NOTE
Takara Belmont (UK) Ltd.
Belmont House
One St.Andrews Way,Bow,
London E3 3PA U.K.
Tel: (44)20 7515 0333
Fax:(44)20 7987 3596
TAKARA BELMONT CORPORATION
2-1-1, Higashishinsaibashi,Chuo-ku,Osaka, 542-0083, Japan
TEL : 81-6-6213-5945
FAX : 81-6-6212-3680
BOOK NO. AEFT16H0
Printed in Japan 1110
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement