Operating Instructions - ACS-Control
User manual M2
Thermocouple Type K, B, S, N, E, T, R, L, J
User manual M2
Operating Instructions
Thermocouple Type K, B, S, N, E, T, R, L, J
DAL-111x800S
Thermo couple Typ K, B, S, N, E, T, R, L, J
Technical features:
• red display of -19999…99999 digits (optional: green, orange or blue display)
features: depth: 70 mm without plug-in screw terminal
•Technical
minimal installation
• min/max-memory
• red display of -19999…99999 digits (optional: green, orange or blue display)
• display flashing at threshold value exceedance / threshold value undercut
• minimal installation depth: 70 mm without plug-in screw terminal
• permanent min/max-value recording
• min/max-memory
• brightness control
• display flashing at threshold value exceedance / threshold value undercut
• programming interlock via access code
• permanent min/max-value recording
• protection class IP65 at the front side
• brightness control
• plug-in screw terminal
• programming interlock via access code
• optional: 2 relay outputs
• protection class IP65 at the front side
• optional: analog output
• plug-in screw terminal
• accessories: PC-based configuration-kit PM-TOOL with CD & USB-adapter for devices without
• optional: 2 relay
outputs
keypad
and for a simple adjustment of standard devices
• optional: analog output
• accessories: PC-based configuration-kit PM-TOOL with CD & USB-adapter for devices without
keypad and for a simple adjustment of standard devices
M2_1TGB.pdf update: 12.03.2015
96x48
M2_1TGB.pdf update: 12.03.2015
96x48
Order code
0
2
3
4
power supply
230V AC
10...30V DC galvanic seperated
230V AC with sensor supply 24V DC/50 mA and digital input (no analog output possible)1)
10...30V DC galvanic seperated with sensor supply 24V DC/ 50 mA and
digital input (no analog output possible) 1)
9
function input
weighing technology
0
DAL-111
2
8
0
function output
display
0
standard configuration
S
0
standard, protection IP65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
Contents
1.
Brief description
2
2.
Assembly
3
3.
Electrical connection
4
4.
Functions and operation description
5
4.1. Programming software PM-TOOL
6
Setting up the device
7
5.1. Switching on
7
5.2. Standard parameterisation (flat operation level)
7
5.
Value assigment for triggering of the singal input
5.3. Programming interlock „RUN“
10
Activation/Deactivation of the programming interlock or change into the professional level
respectively back into the flat operation level
5.4. Extended parameterisation (professional operation level)
5.4.1. Signal input parameter „INP“
11
11
Value assigment for triggering of the singal input
5.4.2. General device parameter „FCT“
13
Higher device functions like min/max permanent, brightness control, as well as the control of
the keyboard configuration
5.4.3. Safety parameter „COD“
15
Assignment of user and master code for locking or access to certain
parameters like e.g. analog output and alarms, etc.
5.4.4. Analog output parameter „Out“
16
Analog output functions
5.4.5. Relay functions „rel“
18
Parameter for the definition of the setpoints
5.4.6. Alarm parameter „AL1…AL4“
20
Activator and dependencies of the alarms
6.
Reset to factory settings
21
Reset of the parameter to the factory default settings
7.
Alarms / Relays
22
Function principle of the switching outputs
8.
Technical data
23
9.
Safety advices
25
10.
Error elimination
26
1
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
3
1. Brief description
1. Brief description
1.
1. Brief
Brief description
description
The panel meter DAL-111 is a 5-digit device for several thermocouple types and a visual threshold value moniThe panel meter M2-1T is a 5-digit device for several thermocouple types and a visual threshold value
The panel
M2-1T
is a 5-digit device
for via
several
thermocouple
and a PC
visual
threshold
value
toring
via themeter
display.
The configuration
happens
four front
keys or viatypes
the optional
software
PM-TOOL.
monitoring via the display. The configuration happens via four front keys or via the optional PC software PMmonitoring
viaprogramming
the display. The
configuration
via four
front keys
or via
the optional
software
PMAn
integrated
interlock
preventshappens
unrequested
changes
of the
parameters
andPC
can
be unlocked
TOOL. An integrated programming interlock prevents unrequested changes of the parameters and can be
TOOL.
prevents
unrequested
changesa of
the parameters
and can
be
again
byAn
anintegrated
individual programming
code. Optionalinterlock
the following
functions
are available:
supply
for the sensor,
a digital
unlocked again by an individual code. Optional an analog output for further processing in the equipment is
unlocked
again byofanHold
individual
code.
Optional
an analog
output
for furtherinprocessing
in the equipment is
input
for triggering
(Tara) or
an analog
output
for further
processing
the equipment.
available. And on demand two free adjustable setpoints with which threshold values can be controlled and
available.
And
onoptional
demandgalvanic
two freeisolated
adjustable
setpoints
which threshold
By
use of the
two
setpoints,
freewith
adjustable
thresholdvalues
valuescan
can be
be controlled
controlled and
and
reported to a superior master display.
reportedto
toaasuperior
superior master
master display.
display. The electrical connection is carried out on the back side via plug-in terreported
The electrical connection is carried out on the back side via plug-in terminals.
The electrical connection is carried out on the back side via plug-in terminals.
minals.
Selectable functions like e.g. the request of the min/max-value or a direct change of threshold value in
Selectablefunctions
functionslike
likee.g.
e.g.thethe
request
of the
min/max-value
a direct
change of threshold
value in
Selectable
request
of the
min/max-value,
an or
average
determination
of the measuring
operation mode complete the modern device concept.
operation
mode complete
the modern setpoint
device concept.
signals,
a nominal
preset respectively
preset, a direct change of threshold value in operation mode
and additional measuring supporting points for linearisation complete the modern device concept.
4
2
2
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
2. Assembly
2. Assembly
Please read the Safety advices on page 25 before installation and keep this user manual for future reference.
48,0
3,0
Se
alin
g
M2
,0
89
Gap for physical unit
1.
2.
3.
After removing the fixing elements, insert the device.
Check the seal to make sure it fits securely.
Click the fixing elements back into place and tighten the clamping screws by hand. Then use a
screwdriver to tighten them another half a turn.
CAUTION! The torque should not exceed 0.1 Nm!
The dimension symbols can be exchanged before installation via a channel on the side!
3
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5
3. Electrical connection
3. Electrical connection
with a supply of 230 VAC
Type M2-1TR5B.040X.570CD
DAL-111x800S
Type M2-1TR5B.040X.670CD
DAL-111x800S
with a supply of 10-30 VAC
6
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-843074Eggenfelden l www.acs-controlsystem.de l [email protected]
4. Function and operation description
4. Function and operation description
Operation
The operation is divided into three different levels.
Menu level (delivery status)
This level is for the standard settings of the device. Only menu items which are sufficent to set the device
into operation are displayed. To get into the professional level, run through the menu level and parameterise
“prof“ under menu item RUN.
Menu group level (complete function volume)
Suited for complex applications as e.g. linkage of alarms, setpoint treatment, totaliser function etc. In this
level function groups which allow an extended parameterisation of the standard settings are availabe. To
leave the menu group level, run through this level and parameterise „uloc„ under menu item RUN.
Parameterisation level:
Parameter deposited in the menu item can here be parameterised. Functions, that can be changed or
adjusted, are always signalised by a flashing of the display. Settings that are made in the parameterisation
level are confirmed with [P] and thus safed. By pressing the [O]-key (zero-key) it leads to a break-off of the
value input and to a change into the menu level. All adjustments are safed automatically by the device and it
changes into operating mode, if no further key operation is done within the next 10 seconds.
Level
Key
Description
Change to parameterisation level and deposited values.
Menu level
Keys for up and down navigation in the menu level.
Change into operation mode.
To confirm the changes made at the parameterization level.
Parameterisation
level
Adjustment of the value / the setting.
Change into menu level or break-off in value input.
Change to menu level.
Menu group level
Keys for up and down navigation in the menu group level.
Change into operation mode or back into menu level.
5
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
7
4. Function and operation description
Function chart:
4.1 Parameterisation software PM-TOOL:
Part of the PM-TOOL are the software on CD and an USB-cable with device adapter. The connection
happens via a 4-pole micromatch-plug on the back side of the device, to the PC-side the connection
happens via an USB plug.
System requirements: PC incl. USB interface
Software: Windows XP, Windows VISTA
With this tool the device configuration can be generated, omitted and safed on the PC. The parameters can
be changed via the easy to handle program surface, whereat the operating mode and the possible selection
options can be preset by the program.
CAUTION!
During parameterisation with connected measuring signal, make sure that the measuring signal has no
mass supply to the programming plug. The programming adapter is galvanic not isolated and directly
connected with the PC. Via polarity of the input signal, a current can discharge via the adapter and destroy
the device as well as other connected components!
8
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
6
5. Setting up the device
5. Setting up the device
5.1. Switching-on
Once the installation is complete, you can start the device by applying the voltage supply. First, check once
again that all electrical connections are correct.
Starting sequence
For 1 second during the switching-on process, the segment test (8 8 8 8 8) is displayed followed by an
indication of the software type and, after that, also for 1 second the software version. After the starting
sequence, the device switches to operation/display mode.
5.2. Standard parameterisation: (Flat operation level)
To parameterise the display, press the [P] key in operating mode for 1 second. The display then changes to
the menu level with the first menu item TYPE.
Menu level
Parameterisation level
Selection of the input signal, tYPE:
Default: typ.l
Available are 9 types of thermocouple as input options (L, J, K, B, S, N, E, T, R). Confirm the
selection with [P] and the display switches back to menu level.
Type of temperature measurement, UNIT:
Default: °c
Select between °C and °F to display the temperature. Confirm the selection with [P] and the
display switches back to menu level.
Setting the decimal point / physical unit, DOT:
Default: 0.0
The decimal point and the physical unit of the device can be adjusted with [▼] [▲]. If e.g.
temperature measurement was selected in °C, one can select 0°C respectively 0.0°C in the
parameterisation level. Confirm the selection with [P] and the display switches back to menu
level.
Reference junction correction, OFFS:
Default: 0.0
The value for the sensor calibration is aligned from the smallest to the highest digit [▼] [▲] and
confirmed digit per digit with [P]. After the last digit, the device changes back into menu level.
During a temperature measurement in °C the value calibration can be adjusted between -20.0
and +20.0 and can be set during a measurement in °F between -36.0 and +36.0. The adjusted
offset temperature is added on the reference junction temperature and then allocated as a
proportional thermo voltage. An alignment of the offset needs to be done, based on a reference
temperature of the reference junction temperature (generally 10°C…40°C). If the measurement
is switched later on, the value is rounded.
7
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
9
5. Setting up the device
Menu level
Parameterisation level
Setting up the display time, SEC:
Default: 1.0
then
The display time is set with [▲] [▼]. The display moves up in increments of 0.1 up to 1 second
and in increments of 1.0 up to 10.0 seconds. Confirm the selection by pressing the [P] button.
The display then switches back to the menu level again.
Selection of analog output, Out.rA:
Default: 4-20
Three output signals are available: 0-10 VDC, 0-20 mA and 4-20 mA, with this function, the
demanded signal is selected.
Setting up the final value of the analog output, Out.En:
Default: 850.0
The final value is adjusted from the smallest digit to the highest digit with [▲] [▼] and digit by
digit confirmed with [P]. A minus sign can only be parameterised on the highest digit. After the
last digit, the device changes back into menu level.
Setting up the initial value of the analog output, Out.OF:
Default: -200.0
The final value is adjusted from the smallest digit to the highest digit with [▲] [▼] and digit by
digit confirmed with [P]. A minus sign can only be parameterised on the highest digit. After the
last digit, the device changes back into menu level.
Threshold values / limit values, LI-1:
Default: 200.0
This limit value defines the threshold, that leads to an activation / deactivation of the alarm.
Hysteresis for limit values, HY-1:
Default: 0.0
The difference to the threshold value that causes the delay of the actuation of the alarm, is
defined by the hysteresis.
8
10
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
Menu level
Parameterisation level
Function if display falls below / exceeds limit value, FU-1:
Default: high
The limit value undercut can be selected with Louu (LOW = lower limit value) and limit value
exceedance can be selected with high (HIGH = upper limit value). If e.g. limit value 1 is on a
switching threshold of 100 and occupied with function high, the alarm will be activated by
reaching the threshold. If the limit value is allocated to Low, an alarm will be activated by
undercut of the threshold.
Threshold values / limit values, LI-2:
Default: 300.0
This limit value defines the threshold, that leads to an activation / deactivation of the alarm.
Hysteresis for threshold values, HY-2:
Default: 0.0
The difference to the threshold value that causes the delay of the actuation of the alarm, is
defined by the hysteresis.
Function if display falls below / exceeds limit value, FU-2
Default: high
The limit value undercut can be selected with Louu (LOW = lower limit value) and limit value
exceedance can be selected with high (HIGH = upper limit value). If e.g. limit value 1 is on a
switching threshold of 100 and occupied with function high, the alarm will be activated by
reaching the threshold. If the limit value is allocated to Low, an alarm will be activated by
undercut of the threshold.
User code (4-digit number-combination, free available), U.CodE:
Default: 0000
If this code is set (>0000), all parameters are locked for the user, if LOC has been selected under
menu item run. By pressing [P] for approx. 3 seconds in operation mode, the message CODE is
shown in the display. Enter the preset u.code to get access to the for the user unlocked set of
parameters. The code needs to be entered bevor each try of parameterisation, as long as
A.Code (Master code) all parameters are unlocked again.
9
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
11
5. Setting up the device
Menu level
Parameterisation level
Master code (4-digit number-combination free available), A.CodE:
Default: 1234
After LOC has been activated under menu item Run, this code can be used for unlocking all
parameters. By pressing [P] for approx. 3 seconds in operation mode, the message CODE is
shown in the display and offer the user access to all parameters by entering A.codE. While
leaving this parameterisation it can be unlocked permanently under run by selecting ULOC or
ProF. So, at an anew pressing of [P] in operating mode, an anew entereing of the code is not
needed.
5.3. Programming interlock
Activation / Deactivation of the programming interlock or completion of the standard
parameterisation with change into menu group level (complete function volume), run:
Default: uloc
Choose between the deactivated key lock Uloc (works setting), the activated key lock Loc, or the
menu group level ProF with the navigation keys [▲] [▼]. Confirm the selection with [P]. After
this, the display confirms the settings with "- - - - -", and automatically switches to operating
mode. If Loc was selected, the keyboard is locked. To get back into the menu level, press [P]
for 3 seconds in operating mode. Now enter the CODE (works setting 1234) that appears using
[▲] [▼] plus [P] to unlock the keyboard. FAIL appears if the input is wrong.
To parameterise further functions, ProF needs to be set. The device confirms this setting with
„- - - - -„ and changes automatically into operation mode. By pressing [P] for approx. 3 seconds
in operation mode, the first menu group InP is shown in the display and thus confirms the
change into the extended parameterisation. It stays as long activated as ULOC is entered in
menu group RUN, thus the display is set back in standard parameterisation again.
12
10
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
5.4. Extended parameterisation (Professional operation level)
5.4.1. Signal input parameters
Menu group level
Menu level
Menu level
Parameterisation level
Selection of the input signal, tYPE:
Default: typ.l
Available are 9 types of thermocouple as input options (L, J, K, B, S, N, E, T, R). Confirm the
selection with [P] and the display switches back to menu level.
Type of temperature measurement, UNIT:
Default: °c
Select between °C and °F to display the temperature. Confirm the selection with [P] and the
display switches back to menu level.
Setting the decimal point / physical unit, DOT:
Default: 0.0
The decimal point and the physical unit of the device can be adjusted with [▼] [▲]. If e.g.
temperature measurement is selected in °C, one can select 0°C respectively 0.0°C in the
parameterisation level. Confirm the selection with [P] and the display switches back to menu
level.
Reference junction correction, OFFS:
Default: 0.0
The value for the sensor calibration is aligned from the smallest to the highest digit [▼] [▲] and
confirmed digit per digit with [P]. After the last digit, the device changes back into menu level.
During a temperature measurement in °C the value calibration can be adjusted between -20.0
and +20.0 and can be set during a measurement in °F between -36.0 and +36.0. The adjusted
offset temperature is added on the reference junction temperarture and then allocated as a
proportional thermo voltage. An alignment of the offset needs to be done, based on a reference
temperature of the reference junction temperature (generally 10°C…40°C). If the measurement
is switched later on, the value is rounded.
11
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
13
5. Setting up the device
Menu level
Parameterisation level
Setting up the display time, SEC:
Default: 1.0
then
The display time is set with [▲] [▼]. The display moves up in increments of 0.1 up to 1 second
and in increments of 1.0 up to 10.0 seconds. Confirm the selection by pressing the [P] button.
The display then switches back to the menu level again.
Device undercut, dI.Und:
Default: -i9999
With this function the device undercut (_ _ _ _ _) can be defined on a definite value. Exception is
input type 4-20 mA, it already shows undercut at a signal <1 mA, so a sensor failure is marked.
Display overflow, dI.OUE:
Default: 99999
_____
With this function the display overflow (
) can be defined on a definite value.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–INP–“.
14
12
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
5.4.2. General device parameters
Menu group level
Menu level
Menu level
Parameterisation level
Display time, DISEC:
Default: 01.0
then
The display time is set up with [▲] [▼]. Thereby switch up to 1 second in increments of 0.1
and up to 10.0 seconds in increments of 1.0. With [P] the selection is confirmed and the device
changes into menu level.
Rounding of display values, round:
Default: 00001
This function is for instable display values, where the display value is changed in 1-, 5-, 10- or
50-steps. This does not affect the resolution of the optional outputs. With [P] the selection is
confirmed and the device changes into menu level.
Display, dISPL:
Default: actua
With this function the current measurand or the min-/max value can be allocated to the display.
With [P] the selection is confirmed and the device changes into menu level.
Brightness control, Light:
Default: 15
The brightness of the display can be adjusted in 16 levels from 00 = very dark to 15 = very
bright via this parameter or alternatively via the navigation keys from the outside. During the
start of the device the level that is deposited under this parameter will always be used, even
though the brightness has been changed via the navigation keys in the meantime.
13
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
15
5. Setting up the device
Menu level
Parameterisation level
Display flashing, FLASH:
Default: no
A display flashing can be added as additional alarm function either to single or to a combination
of off-limit condition. With no, no flashing is allocated.
Assignment (deposit) of key functions, tASt:
Default: no
For the operation mode, special functions can be deposited on the navigation keys [▲] [▼], in
particular this function is made for devices in housing size 48x24mm which do not have a 4th
key ([O]-key). If the min/max-memory is activated with EHtr, all measured min/max-values are
safed during operation and can be recalled via the navigation keys. The values get lost by
restart of the device. If the threshold value correction LI.12 or LI.34 is choosen, the values of the
threshold can be changed during operation without disturbing the operating procedure. Under
Light the brightness can be changed during operation. If no is selected, the navigation keys are
without any function in the operation mode.
Special function [O]-key, tASt.4:
Default: no
For the operation mode, special functions can be deposited on the [O]-key. This function is
activated by pressing the key. Set.OF adds a defined value to the currently displayed value.
EHt.rE deletes the min/max-memory. ActuA shows the measuring value for approx. 7 seconds,
after this the device switches back onto the parameterised display value. If no is selected, the
[O]-key is without any function in the operation mode.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–fct–“.
14
16
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
5.4.3. Safety parameters
Menu group level
Menu level
Menu level
Parameterisation level
Adjustment of user code, U.Code :
Default: 0000
Via this code reduced sets of parameters out.le and al.lev can be unlocked during locked
programming. Further parameters are not available via this code. The U.CodE can only be
changed via the correct input of the A.CodE (Master code).
Master code, A.Code:
Default: 1234
By entering A.CodE the device will be released and all parameters unlocked.
Release/ lock analog output parameters, Out.LE:
Default: all
Analog output parameters can be locked or released for the user:
- at En-oF the initial or final value can be changed in operation mode
- at Out.EO the output signal can be changed from e.g. 0-20 mA to 4-20 mA or 0-10 VDC
- at ALL analog output parameters are released
- at no all analog output parameters are locked
Release/lock alarm parameters, AL.LEU:
Default: all
This parameter describes the user release/user lock of the alarm.
- LIMIt, here only the range of value of the threshold values 1-4 can be changed
- ALrM.L, here the range of value and the alarm trigger can be changed
- ALL, all alarm parameters are released
- no, all alarm parameters are locked
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–cod–“.
15
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
17
5. Setting up the device
5.4.4. Analog output parameters
Menu group level
Menu level
Menu level
Parameterisation level
Selection reference analog output, OutPt:
Default: actua
The analog output signal can refer to different functions, in detail this are the current measuring
value, min-value or max-value. With [P] the selection is confirmed and the device changes into
menu level.
Selection analog output, Out.rA:
Default: 4-20
There are 3 output signals availabe: 0-10 VDC, 0-20 mA and 4-20 mA. With this function the
demanded signal can be selected.
Setting up the final value of the analog output, Out.En:
Default: 850.0
The final value can be adjusted from the smallest to the largest digit with [▲] [▼]. Confirm
each digit with [P]. A minus sign can only be parameterized on the highest value digit. After the
last digit, the display switches back to the menu level.
Setting up the initial value of the analog output, Out.OF:
Default: -200.0
The initial value can be adjusted from the smallest to the largest digit with [▲] [▼]. Confirm
each digit with [P]. A minus sign can only be parameterized on the highest value digit. After the
last digit, the display switches back to the menu level.
18
16
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
Menu level
Parameterisation level
Overflow behavior, O.FLoU:
Default: edge
To recognise and evaluate faulty signals, e.g. by a controller, the overflow behavior of the
analog output can be defined. As overflow can be seen either EdGE, that means the analog
output runs on the set limits e.g. 4 mA and 20 mA, or to.OFF (input value smaller than initial
value, analog output changes on e.g. 4 mA), to.End (higher than final value, analog output
changes on e.g. 20 mA). If to.MIn or to.MAX is set, the analog output changes on the smallest or
highest possible binary value. This means that values of e.g. 0 mA, 0 VDC or values higher
than 20 mA or 10 VDC can be reached. With [P] the selection is confirmed and the device
changes into menu level.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–out–“.
17
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
19
5. Setting up the device
5.4.5. Relay functions
Menu group level
Menu level
Menu level
Parameterisation level
Alerting relay 1, rEL-1:
Default: al-1
….
….
Each setpoint (optional) can be linked up via 4 alarms (by default). This can either be inserted
at activated alarms AL1/4 or deactivated alarms ALN1/4. If LOGIC is selected, logical links are
available in the menu level LoG-1 and CoM-1. Access to these two menu levels is via LOGIC, at all
other selected functions, these two parameters are overleaped. Via On/OFF the setpoints can be
activated/deactivated, in this case the output and the setpoint display are set/not set on the
front of the device. With [P] the selection is confirmed and the device changes into menu level.
Logic relay 1, Log-1
Default: or
Here, the switching behavior of the relay is defined via a logic link, the following schema
describes these functions with inclusion of AL-1 and AL-2: This parameter can only be selected if
LOGIC was selected under REl-1 .
A1 v A2
As soon as a selected alarm is activated, the relay
operates. Equates to operating current principle.
A1 v A2 = A1 Λ A2
The relay operates only, if no selected alarm is
active. Equates to quiescent current principle.
A1 Λ a2
The relay operates only, if all selected alarms are
active.
A1 Λ A2 = A1 v A2
As soon as a selected alarm is not activated, the
relay operates.
____ _ _
____ _ _
With [P] the selection is confirmed and the device changes into menu level.
Alarms for relay 1, CoM-1:
Default: a.1
….
The allocation of the alarms to relay 1 happens via this parameter, one alarm or a group of
alarms can be chosen. This parameter can only be selected if LOGIC was selected under REl-1.
With [P] the selection is confirmed and the device changes into menu level.
20
18
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
Menu level
Parameterisation level
Alerting relay 2, reL-2:
Default: al-2
….
….
Each setpoint (optional) can be linked up via 4 alarms (by default). This can either be inserted
at activated alarms AL1/4 or deactivated alarms ALN1/4. If LOGIC is selected, logical links are
available in the menu level LoG-1 and CoM-1. Access to these two menu levels is via LOGIC, at all
other selected functions, these two parameters are overleaped. Via On/OFF the setpoints can be
activated/deactivated, in this case the output and the setpoint display are set/not set on the
front of the device. With [P] the selection is confirmed and the device changes into menu level.
Logic relay 2, LoG-2:
Default: or
Here, the switching behavior of the relay is defined via a logic link, the following schema
describes these functions with inclusion of AL-1 and AL-2: This parameter can only be selected if
LOGIC was selected under REl-1 .
A1 v A2
As soon as a selected alarm is activated, the relay
operates. Equates to operating current principle.
A1 v A2 = A1 Λ A2
The relay operates only, if no selected alarm is
active. Equates to quiescent current principle.
A1 Λ a2
The relay operates only, if all selected alarms are
active.
A1 Λ A2 = A1 v A2
As soon as a selected alarm is not activated, the
relay operates.
____ _ _
____ _ _
With [P] the selection is confirmed and the device changes into menu level.
Alarms for relay 2, CoM-2:
Default: a.2
….
The allocation of the alarms to relay 1 happens via this parameter, one alarm or a group of
alarms can be chosen. This parameter can only be selected if LOGIC was selected under REl-1.
With [P] the selection is confirmed and the device changes into menu level.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–rel–“ .
19
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
21
5. Setting up the device
5.4.6. Alarm parameters
Menu group level
Menu level
Menu level
Parameterisation level
Depedency of alarm.1, ALrM.1:
Default: actua
The dependency of alarm 1 can be related to special functions, in detail these are the current
measurand, the min-value or the max-value. EHtEr causes the dependency either by pressing
the [O]-key on the front of the housing or by an external signal via the digital input. With [P] the
selection is confirmed and the device changes into menu level.
Example:
By using the maximum value Alarm.1 = Max.va in combination with a threshold monitoring
Fu-1 = High, an alarm confirmation can be realised. Use the navigation keys or the 4th key for
confirmation.
Threshold values / limits, LI-1:
Default: 200.0
This limit value defines the threshold, that leads to an activation / deactivation of the alarm.
Hysteresis for threshold values, HY-1:
Default: 0.0
The difference to the threshold value that causes the delay of the actuation of the alarm, is
defined by the hysteresis.
Function for threshold value exceedance/-undercut, Fu-1:
Default: high
The limit value undercut can be selected with Louu (LOW = lower limit value) and limit value
exceedance can be selected with high (HIGH = upper limit value). If e.g. limit value 1 is on a
switching threshold of 100 and occupied with function high, the alarm will be activated by
reaching the threshold. If the limit value is allocated to Low, an alarm will be activated by
undercut of the threshold.
22
20
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
6. Reset to factory settings
Menu level
Parameterisation level
Switching-on delay, ton-1:
Default: 000
For limit value 1 one can preset a delayed switching-on of 0-100 seconds.
Switching-off delay, toF-1:
Default: 000
For limit value 1 one can preset a delayed switching-off of 0-100 seconds.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–Ali–“.
The same applies to –Al2– to –Al4–.
Programming interlock:
Menu-group level
Description see page 10, menu-level run
6. Reset to factory settings
To return the unit to a defined basic state, a reset can be carried out to the default values.
The following procedure should be used:
• Switch off the power supply
• Press button [P]
• Switch on voltage supply and press [P]-button until „- - - - -“ is shown in the display.
With reset, the default values of the program table are loaded and used for subsequent operation. This sets
the unit back to the state in which it was supplied.
Caution! All application-related data are lost.
21
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
23
7. Alarms / Relays
7. Alarms / Relays
This device has 4 virtual alarms that can monitor one limit value in regard of an undercut or exceedance.
Each alarm can be allocated to an optional relay output S1-S2; furthermore alarms can be controlled by
events like e.g. min/max-value.
Function principle of alarms / relays
Alarm / Relay x
Deactivated, instantaneous value, min/max-value or an activation via the
[O]-key.
Switching threshold
Threshold / limit value of the change-over
Hysteresis
Broadness of the window between the switching thresholds
Working principle
Operating current / Quiescent current
Operating current
By operating current the alarm S1-S2 is off
below the threshold and on on reaching the
threshold.
Quiescent current
By quiescent current the alarm S1-S2 is on
below the threshold and switched off on
reaching the threshold.
Switching-on delay
The switching-on delay is activated via an
alarm and e.g. switched 10 seconds after
reaching the switching threshold, a shortterm exceedance of the switching value does
not cause an alarm, respectively does not
cause a switching operation of the relay. The
switching-off delay operates in the same way,
keeps the alarm / the relay switched longer
for the parameterised time.
22
24
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
8. Technical data
8. Technical data
Housing
Dimensions
96x48x70 mm (BxHxD)
96x48x89 mm (BxHxD) including plug-in terminal
Panel cut-out
92.0+0.8 x 45.0+0.6 mm
Wall thickness
up to 15 mm
Fixing
screw elements
Material
PC Polycarbonate, black, UL94V-0
Sealing material
EPDM, 65 Shore, black
Protection class
standard IP65 (Front), IP00 (Back side)
Weight
approx. 200 g
Connection
plug-in terminal; wire cross-section up to 2.5 mm2
Display
Digit height
14 mm
Segment colour
red (optional green, orange or blue)
Display range
-19999 up to 99999
Setpoints
one LED per setpoint
Overflow
horizontal bars at the top
Underflow
horizontal bars at the top
Display time
0.1 to 10.0 seconds
Input
Measuring range
Measuring error
(at 1 second measuring time)
Digit
Type L (Fe-CuNi alter Typ)
-200.0…-900.0°C
2K
±1
Type J (Fe-CuNi)
-210.0…1200.0°C
2K
±1
Type K (NiCr-NiAL)
-270.0…1372.0°C
2K
±1
Type B (Pt30Rh-Pt6Rh)
80.0…1820.0°C
2K
±1
Type S (Pt10Rh-Pt)
-50.0…1768.0°C
2K
±1
Type N (NiCrSi-NiSi)
-270.0…1300°C
2K
±1
Type E (NiCr-CuNi)
-270.0…1000.0°C
2K
±1
Type T (Cu-Cu-Ni)
-270.0…400.0°C
2K
±1
Type R (Pt13Rh-Pt)
-50.0…1768.0°C
2K
±1
Characteristic line error
< ±1
Reference junction
Thermistor
23
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
25
8. Technical data
Accuracy
Temperature drift
100 ppm / K
Measuring time
0.1…10.0 seconds
Measuring principle
U/F-conversion
Resolution
0.1°C or 0.1°F
Output
Analog output
0/4-20 mA / burden 350 Ohm; 0-10 VDC / burden 10 kOhm, 16 bit
Switching outputs
Relay with change-over contacts
Switching cycles
250 VAC / 5 AAC; 30 VDC / 5 ADC
30 x 103 at 5 AAC, 5 ADC ohm resistive burden
10 x 106 mechanically
Diversification according to DIN EN50178 /
Characteristics according to DIN EN60255
Power supply
230 VAC 50/60 Hz, ±10 % max. 10 VA
10-30 VDC galv. isolated, max. 4 VA
Memory
EEPROM
Data life
≥ 100 years at 25°C
Ambient conditions
26
Working temperature
0…50°C
Storing temperature
-20…80°C
Weathering resistance
relative humidity 0-80% on years average without dew
EMV
EN 61326
CE-sign
Conformity according to directive 2004/108/EG
Safety standard
According to low voltage directive 2006/95/EG
EN 61010; EN 60664-1
24
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
9. Safety advices
9. Safety advices
9. Safety advices
9. Safety advices
Please read the following safety advices and the assembly chapter 2 before installation and keep
Please
readreference.
the following safety advices and the assembly chapter 2 before installation and keep
it
for future
it for future reference.
Proper use
Proper use
The DAL-111--device is designed for the evaluation and display of sensor signals.
The M2-1T-device is designed for the evaluation and display of sensor signals.
The M2-1T-device is designed for the evaluation and display of sensor signals.
Attention! Careless use or improper operation can result in
Attention! Careless
or and/or
improper
operation
can
in
personal use
injury
cause
damage
to result
the equipment.
personal injury and/or cause damage to the equipment.
Control of the device
Control of the device
The panel meters are checked before dispatch and sent out in perfect condition. Should there be
The visible
panel meters
arewe
checked
beforeclose
dispatch
and sentofout
perfect condition.
there be
any
damage,
recommend
examination
theinpackaging.
Please Should
inform the
any
visible
damage,
we
recommend
close
examination
of
the
packaging.
Please
inform
the
supplier immediately of any damage.
supplier immediately of any damage.
Installation
Installation
The M2-1T-device must be installed by a suitably qualified specialist (e.g. with a qualification in
TheM2-1T-device
DAL-111-device
must
installed
bysuitably
a suitably
qualified
specialist(e.g.
(e.g.with
withaaqualification
qualificationinin
The
must
be be
installed
by a
qualified
specialist
industrial
electronics).
industrial
electronics).
industrial electronics).
Notes on installation
Notes on installation
• There must be no magnetic or electric fields in the vicinity of the device, e.g. due to
• There
must be
no phones
magnetic
or electric fields
in the vicinity of the device, e.g. due to
transformers,
mobile
or electrostatic
discharge.
transformers, mobile phones or electrostatic discharge.
• The fuse rating of the supply voltage should not exceed a value of 6A N.B. fuse.
• The fuse rating of the supply voltage should not exceed a value of 6A N.B. fuse.
• Do not install inductive consumers (relays, solenoid valves etc.) near the device and
• Do
not install
inductive with
consumers
solenoid
valvescombinations
etc.) near the
device and
suppress
any interference
the aid of(relays,
RC spark
extinguishing
or free-wheeling
suppress
any
interference
with
the
aid
of
RC
spark
extinguishing
combinations
or
free-wheeling
diodes.
diodes.
• Keep input, output and supply lines separate from one another and do not lay them parallel with
• Keep
input, Position
output and
supply
lines separate
from
one another.
another and
do possible
not lay them
parallel pair.
with
each other.
“go”
and “return
lines” next
to one
Where
use twisted
each
other.
Position
and “return
lines” next to one another. Where possible use twisted pair.
So, you
receive
best “go”
measuring
results.
So, you receive best measuring results.
• Screen off and twist sensor lines. Do not lay current-carrying lines in the vicinity. Connect the
• Screen
off on
andone
twist
sensor
Dopotential
not lay current-carrying
linessignal
in the
vicinity. Connect the
screening
side
on a lines.
suitable
equaliser (normally
ground).
screening on one side on a suitable potential equaliser (normally signal ground).
• The device is not suitable for installation in areas where there is a risk of explosion.
• The device is not suitable for installation in areas where there is a risk of explosion.
• Any electrical connection deviating from the connection diagram can endanger human life
• Any
electrical
connection
deviating from the connection diagram can endanger human life
and/or
can destroy
the equipment.
and/or can destroy the equipment.
• The terminal area of the devices is part of the service. Here electrostatic discharge needs to be
• The
terminal
area ofHigh
the voltages
devices is
part
of the
service. Here
discharge needs to be
avoided.
Attention!
can
cause
dangerous
bodyelectrostatic
currents.
avoided. Attention! High voltages can cause dangerous body currents.
• Galvanic isolated potentials within one complex need to be placed on an appropriate point
• Galvanic
one So,
complex
need
to be placed
on an against
appropriate
point
(normally isolated
earth orpotentials
machineswithin
ground).
a lower
disturbance
sensibility
impacted
(normally
earth
or
machines
ground).
So,
a
lower
disturbance
sensibility
against
impacted
energy can be reached and dangerous potentials, that can occur on long lines or due to faulty
energy
can be
beavoided.
reached and dangerous potentials, that can occur on long lines or due to faulty
wiring, can
wiring, can be avoided.
25
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden
l www.acs-controlsystem.de l [email protected]
25
27
10. Error elimination
10. Error elimination
Error description
Measures
1.
The unit permanently indicates overflow.
• The input has a very high measurement, check the
measuring circuit.
• The input is open.
2.
The unit permanently shows underflow.
• The input has a very low measurement, check the
measuring circuit .
• The input is open.
3.
The word "HELP " lights up in the
7-segment display.
• The unit has found an error in the configuration
memory. Perform a reset on the default values and reconfigure the unit according to your application.
4.
Program numbers for parameterising of
the input are not accessible.
• Programming lock is activated
• Enter correct code
5.
"Err1" lights up in the 7-segment display
• Please contact the manufacturer if errors of this kind
occur.
6.
The device does not react as expected.
• If you are not sure that the device has been parameterised before, then follow the steps as written in
chapter 6 and set it back to its delivery status.
7.
The displayed temperature differs from
the reference temperature.
• Check if the right thermocouple type was selected
under „type“.
• Slightly differences can be corrected via the reference
junction correction „Offs“. If the parameter that needs
to be compensated lies outside of -10…10°C
respectively -18…18°F, then you shoud search for a
systematic error. If the available adjustment range is
not sufficient, a fault in the test setup seems likely.
8.
Clear drift of the displayed temperature
over time.
• Avoid airflow, strong heat sources or switched sinks in
the direct vicinity of the terminal strip of the device.
They lead to measuring errors at the reference
junction. Seal off the connection are of the device, if
neccessary, with help of iron sheets or an appropriate
housing construction.
M2_1TGB.pdf
28
26
update: 12.03.2015
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
29

Pegel
Druck


Temperatur Durchfluss
Registrierung
Visualisierung
¸



Füllstand



Messumformer
Sensorik
USV
Wir erwarten Ihren Anruf.
ACS-CONTROL-SYSTEM GmbH
Lauterbachstr. 57
D- 84307 Eggenfelden
know how mit System
Ihr Partner für Messtechnik und Automation
¸
[email protected]
www.acs-controlsystem.de
Stand 03/2015
ACS-CONTROL-SYSTEM
Tel: +49 (0) 8721-9668-0
Fax: +49 (0) 8721-9668-30
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement