Operating Instructions - ACS-CONTROL
User manual M2
User
manual
M2
Direct voltage
/ direct
current 0-20 mA, 4-20 mA, 0-10 VDC
Operating Instructions
Direct voltage / direct current 0-20 mA, 4-20 mA, 0-10 VDC
DAL-111x000S
Direct voltage / direct current 0-20 mA, 4-20 mA, 0-10 VDC
Technical features:
Technical features:
• red display of -19999…99999 Digits (optional: green, orange or blue display)
minimal
installation
depth: 70 mm
without
plug-in
screw
terminal
•• red
display
of -19999…99999
Digits
(optional:
green,
orange
or blue display)
•• minimal
min/max-memory
installation depth: 70 mm without plug-in screw terminal
•• min/max-memory
30 additional adjustable supporting points
display
flashing
at threshold
value exceedance
/ threshold value undercut
•• 30
additional
adjustable
supporting
points
zero-key
for triggering
of Hold,
Tara
•• display
flashing
at threshold
value
exceedance / threshold value undercut
•• zero-key
permanent
min/max-value
recording
for triggering of Hold, Tara
•• permanent
volume metering
(Totaliser)recording
min/max-value
mathematic
functions
like reciprocal value, square root, squaring or rounding
•• volume
metering
(Totaliser)
setpoint generator
•• mathematic
functions like reciprocal value, square root, squaring or rounding
•• setpoint
sliding average
determination
generator
brightness
control
•• sliding
average
determination
•• brightness
programming
interlock
via access code
control
protection class
IP65 atvia
theaccess
front side
•• programming
interlock
code
•• protection
plug-in screw
terminal
class IP65 at the front side
optional:
2 relay
outputs
•• plug-in
screw
terminal
optional: 2sensor
supply or analog output
•• optional:
relay outputs
optional: sensor
galvanicsupply
isolated
digital input
•• optional:
or analog
output
accessories:
PC-based
configuration-kit
•• optional:
galvanic
isolated
digital input PM-TOOL with CD & USB-adapter for devices without
keypad and for a simple adjustment of standard devices
• accessories: PC-based configuration-kit PM-TOOL with CD & USB-adapter for devices without
keypad and for a simple adjustment of standard devices
M2_11GB.pdf update: 17.03.2015
96x48
M2_11GB.pdf update: 17.03.2015
96x48
Order code
0
2
3
4
power supply
230V AC
10...30V DC galvanic seperated
230V AC with sensor supply 24V DC/50 mA and digital input (no analog output possible)1)
10...30V DC galvanic seperated with sensor supply 24V DC/ 50 mA and
digital input (no analog output possible) 1)
0
function input
0...10V, 0/4...20mA
0
DAL-111
2
0
0
function output
display
0
standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S
0
standard, protection IP65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
Contents
1.
Brief description
2
2.
Assembly
3
3.
Electrical connection
4
4.
Functions and operation description
6
4.1. Programming software PM-TOOL
7
Setting up the device
8
5.1. Switching on
8
5.2. Standard parameterisation (flat operation level)
8
5.
Value assigment for triggering of the singal input
5.3. Programming interlock „RUN“
11
Activation/Deactivation of the programming interlock or change into the professional level
respectively back into the flat operation level
5.4. Extended parameterisation (professional operation level)
5.4.1. Signal input parameter „INP“
12
12
Value assigment for triggering of the singal input incl. linearisation
5.4.2. General device parameter „FCT“
15
Higher device functions like Hold, Tara, min/max permanent, setpoint function respectively
nominal value function, average determination, brightness control, as well as the control of the
digital input and the keyboard configuration
5.4.3. Safety parameter „COD“
19
Assignment of user and master code for locking or access to certain
parameters like e.g. analog output and alarms, etc.
5.4.4. Analog output parameter „Out“
20
Analog output functions
5.4.5. Relay functions „rel“
22
Parameter for the definition of the setpoints
5.4.6. Alarm parameter „AL1…AL4“
24
Activator and dependencies of the alarms
5.4.7. Totaliser (Volume metering) „tot“
26
Parameter for calculation of the sum function
6.
Reset to factory settings
27
Reset of the parameter to the factory default settings
7.
Alarms / Relays
28
Function principle of the switching outputs
8.
Sensor alignment
29
Function diagram for sensors with existing trimming resistor
9.
Technical data
30
10.
Safety advices
32
11.
Error elimination
33
1
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
3
1. Brief description
1. Brief description
The panel
panelmeter
meterDAL-111
M2-11 isis aa 5-digit device
device for
for direct
directcurrent/direct
current/directvoltage
voltagesignals
signalsand
and
a visual
threshold
The
a visual
threshold
value monitoring
monitoringvia
viathe
thedisplay.
display.
configuration
happens
via front
four front
keys
the optional
PC
value
TheThe
configuration
happens
via four
keys or
via or
thevia
optional
PC
software PM-TOOL.
PM-TOOL.An
Anintegrated
integratedprogramming
programminginterlock
interlockprevents
preventsunrequested
unrequestedchanges
changesofofthe
theparameters
parameters
software
and can
can be
be unlocked
unlocked again
again by
by an
an individual
individual code.
code. Optional
Optional the
the following
following functions are available:
available: aa supply
supply for
for
and
the sensor,
sensor,aadigital
digitalinput
input
triggering
of Hold
(Tara)
an analog
for further
processing
the
forfor
triggering
of Hold
(Tara)
or anoranalog
outputoutput
for further
processing
in the in the
equipment.
equipment.
By use
use of
of the
the two
two optional
optional galvanic isolated setpoints, free adjustable threshold values can be
By
be controlled
controlled and
and
reported to
to aa superior
superior master
master display.
display.
reported
The electrical
electrical connection
connection is
is carried
carried out
out on the back side via plug-in terminals.
The
Selectable functions
functions like
like e.g.
e.g.the
therequest
requestofofthe
themin/max-value,
min/max-value,an
anaverage
averagedetermination
determinationofofthe
themeasuring
measuring
Selectable
signals, aa nominal
nominal preset
preset respectively
respectively setpoint
setpointpreset,
preset,aadirect
directchange
changeofofthreshold
thresholdvalue
valueininoperation
operationmode
mode
signals,
and additional
additional measuring
measuring supporting
supporting points for linearisation complete the modern device concept.
and
2
4
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
2. Assembly
2. Assembly
Please read the Safety advices on page 32 before installation and keep this user manual for future reference.
48,0
3,0
Se
alin
g
M2
,0
89
Gap for physical unit
1.
2.
3.
After removing the fixing elements, insert the device.
Check the seal to make sure it fits securely.
Click the fixing elements back into place and tighten the clamping screws by hand. Then use a
screwdriver to tighten them another half a turn.
CAUTION! The torque should not exceed 0.1 Nm!
The dimension symbols can be exchanged before installation via a channel on the side!
3
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5
3. Electrical connection
3. Electrical connection
Type
Type DAL-111x000S
M2-1VT5B.0001.470CD with a supply of 115 VAC
Type DAL-111x000S
M2-1VT5B.0001.570CD with a supply of 230 VAC
Type
Type
M2-1VT5B.0001.670CD with a supply of 10-30 VDC
Type DAL-111x000S
Connection examples:
Below you find some connection examples, which demonstrate some practical applications. Devices with
current inputs / voltage inputs, without sensor supply.
DAL-111 in combination with a
2-wire-sensor 4-20mA
DAL-111 in combination with a
3-wire-sensor 0/4-20mA
DAL-111 in combination with a
3-wire-sensor 0-10V
6
4
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
3. Electrical connection
M2 devicesdevices
DAL-111
With current / voltage input in combination with a 24 VDC sensor supply.
DAL-111 with digital input in combination
with 24 VDC sensor supply
DAL-111 with digital input and
external voltage supply source
5
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
7
4. Function and operation description
4. Function and operation description
Operation
The operation is divided into three different levels.
Menu level (delivery status)
This level is for the standard settings of the device. Only menu items which are sufficent to set the device
into operation are displayed. To get into the professional level, run through the menu level and parameterise
“prof“ under menu item RUN.
Menu group level (complete function volume)
Suited for complex applications as e.g. linkage of alarms, setpoint treatment, totaliser function etc. In this
level function groups which allow an extended parameterisation of the standard settings are availabe. To
leave the menu group level, run through this level and parameterise „uloc„ under menu item RUN.
Parameterisation level:
Parameter deposited in the menu item can here be parameterised. Functions, that can be changed or
adjusted, are always signalised by a flashing of the display. Settings that are made in the parameterisation
level are confirmed with [P] and thus safed. By pressing the [O]-key (zero-key) it leads to a break-off of the
value input and to a change into the menu level. All adjustments are safed automatically by the device and it
changes into operating mode, if no further key operation is done within the next 10 seconds.
Level
Key
Description
Change to parameterisation level and deposited values.
Menu level
Keys for up and down navigation in the menu level.
Change into operation mode.
To confirm the changes made at the parameterization level.
Parameterisation
level
Adjustment of the value / the setting.
Change into menu level or break-off in value input.
Change to menu level.
Menu group level
Keys for up and down navigation in the menu group level.
Change into operation mode or back into menu level.
8
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-843076Eggenfelden l www.acs-controlsystem.de l [email protected]
4. Function and operation description
Function chart:
4.1 Parameterisation software PM-TOOL:
Part of the PM-TOOL are the software on CD and an USB-cable with device adapter. The connection
happens via a 4-pole micromatch-plug on the back side of the device, to the PC-side the connection
happens via an USB plug.
System requirements: PC incl. USB interface
Software: Windows XP, Windows VISTA
With this tool the device configuration can be generated, omitted and safed on the PC. The parameters can
be changed via the easy to handle program surface, whereat the operating mode and the possible selection
options can be preset by the program.
CAUTION!
During parameterisation with connected measuring signal, make sure that the measuring signal has no
mass supply to the programming plug. The programming adapter is galvanic not isolated and directly
connected with the PC. Via polarity of the input signal, a current can discharge via the adapter and destroy
the device as well as other connected components!
7
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
9
5. Setting up the device
5. Setting up the device
5.1. Switching-on
Once the installation is complete, you can start the device by applying the voltage supply. First, check once
again that all electrical connections are correct.
Starting sequence
For 1 second during the switching-on process, the segment test (8 8 8 8 8) is displayed followed by an
indication of the software type and, after that, also for 1 second the software version. After the starting
sequence, the device switches to operation/display mode.
5.2. Standard parameterisation: (Flat operation level)
To parameterise the display, press the [P]-key in operating mode for 1 second. The display then changes to
the menu level with the first menu item TYPE.
Menu level
Parameterisation level
Selection of the input signal, TYPE:
Default: sens.u
There are several measuring input options: 0-20 mA, 4-20 mA or 0-10 VDC signals as works
calibration (without application of the sensor signal) and SenSU (voltage) or SENSA (current) as
sensor calibration (with the sensor applied). Confirm the selection with [P] and the display
switches back to menu level.
Setting the measuring range end value, END:
Default: 10000
Set the end value from the smallest to the highest digit with [▲] [▼] and confirm each digit with
[P]. A minus sign can only be parameterized on the highest value digit. After the last digit, the
display switches back to the menu level. If Sens was selected as input option, one can only
select between noca and cal. With noca, only the previously set display value is taken over, and
with cal, the device takes over both the display value and the analogue input value
Setting up the measuring range start/offset value, offs:
Default: 0
Enter the start/offset value from the smallest to the highest digit with [▲] [▼] and confirm each
digit with [P]. After the last digit the display switches back to the menu level. If Sens was
selected as input option, one can only select between noca and cal. With noca, only the
previously set display value is taken over, and with cal, the device takes over both the display
value and the analogue input value.
10
8
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
Menu level
Parameterisation level
Setting the comma, decimal point, dot:
Default: 0
The decimal point on the display can be moved with [▲] [▼] and confirmed with [P]. The
display then switches back to the menu level again.
Setting up the display time, SEC:
Default: 1.0
then
The display time is set with [▲] [▼]. The display moves up in increments of 0.1 up to 1 second
and in increments of 1.0 up to 10.0 seconds. Confirm the selection by pressing the [P] button.
The display then switches back to the menu level again.
Selection of analog output, Out.rA:
Default: 4-20
Three output signals are available: 0-10 VDC, 0-20 mA and 4-20 mA, with this function, the
demanded signal is selected.
Setting up the final value of the analog output, Out.En:
Default: 10000
The final value is adjusted from the smallest digit to the highest digit with [▲] [▼] and digit by
digit confirmed with [P]. A minus sign can only be parameterised on the highest digit. After the
last digit, the device changes back into menu level.
Setting up the initial value of the analog output, Out.OF:
Default: 0
The final value is adjusted from the smallest digit to the highest digit with [▲] [▼] and digit by
digit confirmed with [P]. A minus sign can only be parameterised on the highest digit. After the
last digit, the device changes back into menu level.
Threshold values / limit values, LI-1:
Default: 2000
This limit value defines the threshold, that leads to an activation / deactivation of the alarm.
9
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
11
5. Setting up the device
Menu level
Parameterisation level
Hysteresis for limit values, HY-1:
Default: 0
The difference to the threshold value that causes the delay of the actuation of the alarm, is
defined by the hysteresis.
Function if display falls below / exceeds limit value, FU-1:
Default: high
The limit value undercut can be selected with Louu (LOW = lower limit value) and limit value
exceedance can be selected with high (HIGH = upper limit value). If e.g. limit value 1 is on a
switching threshold of 100 and occupied with function high, the alarm will be activated by
reaching the threshold. If the limit value is allocated to Low, an alarm will be activated by
undercut of the threshold.
Threshold values / limit values, LI-2:
Default: 3000
This limit value defines the threshold, that leads to an activation / deactivation of the alarm.
Hysteresis for threshold values, HY-2:
Default: 0
The difference to the threshold value that causes the delay of the actuation of the alarm, is
defined by the hysteresis.
Function if display falls below / exceeds limit value, FU-2
Default: high
The limit value undercut can be selected with Louu (LOW = lower limit value) and limit value
exceedance can be selected with high (HIGH = upper limit value). If e.g. limit value 1 is on a
switching threshold of 100 and occupied with function high, the alarm will be activated by
reaching the threshold. If the limit value is allocated to Low, an alarm will be activated by
undercut of the threshold.
12
10
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
Menu level
Parameterisation level
User code (4-digit number-combination, free available), U.CodE:
Default: 0000
If this code is set (>0000), all parameters are locked for the user, if LOC has been selected under
menu item run. By pressing [P] for approx. 3 seconds in operation mode, the message CODE is
shown in the display. Enter the preset u.code to get access to the for the user unlocked set of
parameters. The code needs to be entered bevor each try of parameterisation, as long as all
parameters are released by the A.Code (Master code) again.
Master code (4-digit number-combination free available), A.CodE:
Default: 1234
After LOC has been activated under menu item Run, this code can be used for unlocking all
parameters. By pressing [P] for approx. 3 seconds in operation mode, the message CODE is
shown in the display and offer the user access to all parameters by entering A.codE. While
leaving this parameterisation it can be unlocked permanently under run by selecting ULOC or
ProF. So, at an anew pressing of [P] in operating mode, an anew entereing of the code is not
needed.
5.3. Programming interlock
Activation / Deactivation of the programming interlock or completion of the standard
parameterisation with change into menu group level (complete function volume), run:
Default: uloc
Choose between the deactivated key lock Uloc (works setting), the activated key lock Loc, or the
menu group level ProF with the navigation keys [▲] [▼]. Confirm the selection with [P]. After
this, the display confirms the settings with "- - - - -", and automatically switches to operating
mode. If Loc was selected, the keyboard is locked. To get back into the menu level, press [P]
for 3 seconds in operating mode. Now enter the CODE (works setting 1234) that appears using
[▲] [▼] plus [P] to unlock the keyboard. FAIL appears if the input is wrong.
To parameterise further functions, ProF needs to be set. The device confirms this setting with
„- - - - - „ and changes automatically into operation mode. By pressing [P] for approx. 3 seconds
in operation mode, the first menu group InP is shown in the display and thus confirms the
change into the extended parameterisation. It stays as long activated as ULOC is entered in
menu group RUN, thus the display is set back in standard parameterisation again.
11
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
13
5. Setting up the device
5.4. Extended parameterisation (Professional operation level)
5.4.1. Signal input parameters
Menu group level
Menu level
Menu level
Parameterisation level
Selection of the input signal, TYPE:
Default: sens.u
There are several measuring input options: 0-20 mA, 4-20 mA or 0-10 VDC signals as works
calibration (without application of the sensor signal) and SenSU (voltage) or SENSA (current) as
sensor calibration (with the sensor applied). Confirm the selection with [P] and the display
switches back to menu level.
Setting the measuring range end value, END :
Default: 10000
Set the end value from the smallest to the highest digit with [▲] [▼] and confirm each digit with
[P]. A minus sign can only be parameterized on the highest value digit. After the last digit, the
display switches back to the menu level. If Sens was selected as input option, one can only
select between noca and cal. With noca, only the previously set display value is taken over, and
with cal, the device takes over both the display value and the analogue input value
Setting up the measuring range start/offset value, offs:
Default: 0
Enter the start/offset value from the smallest to the highest digit with [▲] [▼] and confirm each
digit with [P]. After the last digit the display switches back to the menu level. If Sens was
selected as input option, one can only select between noca and cal. With noca, only the
previously set display value is taken over, and with cal, the device takes over both the display
value and the analogue input value.
Setting the comma, decimal point, dot:
Default: 0
The decimal point on the display can be moved with [▲] [▼] and confirmed with [P]. The
display then switches back to the menu level again.
14
12
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
Menu level
Parameterisation level
Setting up the display time, SEC:
Default: 1.0
then
The display time is set with [▲] [▼]. The display moves up in increments of 0.1 up to 1 second
and in increments of 1.0 up to 10.0 second. Confirm the selection by pressing the [P] button.
The display then switches back to the menu level again.
Rescaling the measuring input values, EndA:
Default: 10000
With this function, rescale the input value of e.g. 19.5 mA (works setting) without applying a
measuring signal.
Rescaling the measuring input values, OFFA:
Default: 0
With this function, rescale the input value of e.g. 3.5 mA (works setting) without applying a
measuring signal.
Setting up the tare/offset value, tArA:
Default: 0
The given value is added to the linearized value. In this way, the characteristic line can be
shifted by the selected amount.
Setting up the balance point, Adj.pt:
Default: 08000
The balance point for the final value can be chosen from the measuring range by Sens.u with
0…10 V or Sens.A with 0…20 mA in %. The preset 80.000% result from the widespread
detuning of the melt pressure sensors.
Setting up the physical unit, UnIt:
Default: no
One can choose between the above shown physical units. It will be displayed on the 5th digit of
the display, thus the range of value is limited to -1999…9999.
13
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
15
5. Setting up the device
Menu level
Parameterisation level
Number of additional setpoints, SPCt:
Default: 00
30 additional setpoints can be defined to the initial- and final value, so linear sensor values are
not linearised. Only activated setpoint parameters are displayed.
Display values for setpoints, dIS.01 … dIS.30:
Under this parameter setpoints are defined according to their value. At the sensor calibration,
like at final value/offset, one is asked at the end if a calibration shall be activated.
Analog values for setpoints, InP.01 … InP.30:
The setpoints are always preset according to the selected input signal mA/V. The demanded
analog values can be freely adjusted in ascending order.
Device undercut, dI.Und:
Default: -i9999
With this function the device undercut (_ _ _ _ _) can be defined on a definite value. Exception is
input type 4-20 mA, it already shows undercut at a signal <1 mA, so a sensor failure is marked.
Display overflow, dI.OUE:
Default: 99999
_____
With this function the display overflow (
) can be defined on a definite value.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–INP–“.
16
14
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
5.4.2. General device parameters
Menu group level
Menu level
Menu level
Parameterisation level
Display time, DISEC:
Default: 01.0
then
The display time is set up with [▲] [▼]. Thereby switch up to 1 second in increments of 0.1
and up to 10.0 seconds in increments of 1.0. With [P] the selection is confirmed and the device
changes into menu level.
Rounding of display values, round:
Default: 00001
This function is for instable display values, where the display value is changed in steps of 1, 5,
10 or 50. This does not affect the resolution of the optional outputs. With [P] the selection is
confirmed and the device changes into menu level.
Arithmetics, ArItH:
Default: no
Reciprocal
Root extraction
Square
With this function the calculated value, not the measurand, is shown in the display. With no, no
calulation is deposited. With [P] the selection is confirmed and the device changes into menu
level.
Sliding average determination, AVG:
Default: 10
Under this menu item, the number of measurements that need to be averaged are preset. The
averaging time results from the product of measuring time SEC and the averaged measurements
AVG. With selection of AVG in menu level DISPL the result is shown in the display and evaluated
when entered in the alarm AL1-Al4 or the analog output Outpt.
Zero point slowdown, ZErO:
Default: 00
At the zero point slowdown, a value range around the zero point can be preset, so the display
shows a zero. If e.g.10 is set, the display would show a zero in the value range from -10 to +10;
below continue with -11 and beyond with +11. The maximum adjustable range of value is 99.
15
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
17
5. Setting up the device
Menu level
Parameterisation level
Solid contstant value, const:
Default: 0
The constant value can be evaluated like the current measurand via the alarms or the analog
output. The decimal place cannot be changed for this value and is taken over from the current
measurand. So, with this value a setpoint generator can be realised via the analog output.
Furthermore it can be used as calculated difference. At this the constant value needs to be
subtracted from the current measurand and the difference is evaluated in the alerting or via the
analog output. Thus regulation can be displayed quite easy with this parameterisation.
Minimum constant value, con.mi:
Default: -i9999
The minimum constant value is selected and adjusted from the smallest to the highest digit with
[▲] [▼] and confirmed digit per digit with [P]. A minus sign can only be adjusted on the highest
digit. After the last digit the display changes back into menu level.
Maximum constant value, con.ma:
Default: 99999
The maximum constant value is selected and adjusted from the smallest to the highest digit
with [▲] [▼] and confirmed digit per digit with [P]. A minus sign can only be adjusted on the
highest digit. After the last digit the display changes back into menu level.
Display, dISPL:
Default: actua
With this function the current measurand, the min/max-value, the totaliser, the processcontrolled hold-value, the sliding average value, the constant value or the difference between
constant value and current value can be allocated to the display. With [P] the selection is
confirmed and the device changes into menu level.
Brightness control, Light:
Default: 10
The brightness of the display can be adjusted in 11 levels from 00 = very dark to 10 = very
bright via this parameter or alternatively via the navigation keys from the outside. During the
start of the device the level that is deposited under this parameter will always be used, even
though the brightness has been changed via the navigation keys in the meantime.
18
16
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
Menu level
Parameterisation level
Display flashing, FLASH:
Default: no
A display flashing can be added as additional alarm function either to single or to a combination
of off-limit condition. With no, no flashing is allocated.
Assignment (deposit) of key functions, tASt:
Default: no
For operation mode, special functions can be deposited on the navigation keys [▲] [▼], in
particular this function was made for devices in housing size 48x24mm which do not have a 4th
key ([O]-key). If the min/max-memory is activated with EHtr, all measured min/max-values are
safed during operation and can be recalled via the navigation keys. The values get lost by
restart of the device. If the threshold value correction LI.12 or LI.34 is choosen, the values of the
threshold can be changed during operation without disturbing the operating procedure. With
tArA the device is set temporarily on a parameterised value. The device acknowledges the
correct taring with oo0oo in the display. Set.tA switches into the offset value and can be adjusted
via the navigation keys. Via totAL the current value of the totaliser can be displayed for approx.
7 seconds, after this the device switches back on the parameterised display value. If tot.rE is
deposited, the totaliser can be set back by pressing the navigation keys [▲] [▼], the device
acknowledges this with ooooo in the display. By allocation on EHt.rE the min/max-memory is
deleted. At ActuA the measuring value is shown for approx. 7 seconds, after this the device
switches back on the parameterised display value. With light the brightness of the display is
adjusted. This setting is not safed and gets lost during a restart of the device. Via selection L1.1,
L1.1-2, li.1-3, l1.1-4 threshold values can be addressed via the navigation keys; they can be
changed digit per digit or taken over by pushing the [P]-key. The adjustment is taken over
directly, an excisting limit value monitoring and the current measurement will not be influenced
by this. If no is selected, the navigation keys are without any function in the operation mode.
17
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
19
5. Setting up the device
Menu level
Parameterisation level
Special function [O]-key, tASt.4:
Default: no
…
For the operation mode, special functions can be deposited on the [O]-key. Activate this
function by pressing the key. With tArA the device is set temporarily on zero and safed
permanently as offset. The device acknowledges the correct taring by showing ooooo in the
display. Set.tA switches into the offset value and can be adjusted via the navigation keys. Via
totAL the current value of the totaliser can be displayed for approx. 7 seconds, after this the
device switches back on the parameterised display value. If tot.rE is deposited, the totaliser
can be set back by pressing the navigation keys [▲] [▼], the device acknowledges this with
ooooo in the display. EHt.rE deletes the min/max-memory. If HOLD has been selected, the moment
can be held constant by pressing the [O]-key and is updated by releasing the key. Advice: Hold
is activated only, if HOLD was selected under parameter DISPL. ActuA shows the measurand for
approx. 7 seconds, after this the device switches back on the parameterised display value. The
same goes for AvG, here the sliding average value will be displayed. Via se.cal a sensor
calibration is done by pressing the zero key, the operating diagram is shown in chapter 8. The
constant value const can be called up via the key or adjusted digit per digit. At AL-1…AL-4 an
output can be set and therewith can e.g. a setpoint adjustment be done. If no is selected, the
[O]-key is without any function in the operation mode.
Special function digital input, dIG.In:
Default: no
…
For the operation mode, the above shown parameters can be laid on the optional digital input,
too. Functions description see tASt.4.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–fct–“.
20
18
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
5.4.3. Safety parameters
Menu group level
Menu level
Menu level
Parameterisation level
Adjustment of user code, U.Code:
Default: 0000
Via this code reduced sets of parameters out.le and al.lev can be released during locked
programming. Further parameters are not available via this code. The U.CodE can only be
changed via the correct input of the A.CodE (Master code).
Master code, A.Code:
Default: 1234
By entering A.CodE the device will be released and all parameters unlocked.
Release/ lock analog output parameters, Out.LE:
Default: all
Analog output parameters can be locked or released for the user:
- En-oF: the initial or final value can be changed in operation mode
- Out.EO: the output signal can be changed from e.g. 0-20 mA to 4-20 mA or 0-10 VDC
- ALL: analog output parameters are released
- no: all analog output parameters are locked
Release/lock alarm parameters, AL.LEU:
Default: all
This parameter describes the user release/user lock of the alarm.
- LIMIt: here only the range of value of the threshold values 1-4 can be changed
- ALrM.L: here the range of value and the alarm trigger can be changed
- ALL: all alarm parameters are released
- no: all alarm parameters are locked
19
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
21
5. Setting up the device
Menu level
Parameterisation level
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–cod–“.
5.4.4. Analog output parameters
Menu group level
Menu level
Menu level
Parameterisation level
Selection reference analog output, OutPt:
Default: actua
The analog output signal can refer to different functions, in detail this are the current
measurand, min/max-value or totaliser function/sum-function, the sliding average value, the
constant value or the difference between the current value and the constant value. If HoLd is
selected the signal of the analog output will be hold and processed just after deactivation of
HOLD. With [P] the selection is confirmed and the device changes into menu level.
Selection analog output, Out.rA:
Default: 4-20
There are 3 output signals availabe: 0-10 VDC, 0-20 mA and 4-20 mA. With this function the
demanded signal can be selected.
Setting up the final value of the analog output, Out.En:
Default: 10000
The final value can be adjusted from the smallest to the largest digit with [▲] [▼]. Confirm
each digit with [P]. A minus sign can only be parameterized on the highest value digit. After the
last digit, the display switches back to the menu level.
22
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
20
5. Setting up the device
Menu level
Parameterisation level
Setting up the initial value of the analog output, Out.OF:
Default: 00000
The initial value can be adjusted from the smallest to the largest digit with [▲] [▼]. Confirm
each digit with [P]. A minus sign can only be parameterized on the highest value digit. After the
last digit, the display switches back to the menu level.
Overflow behavior, O.FLoU:
Default: edge
To recognise and evaluate faulty signals, e.g. by a controller, the overflow behavior of the
analog output can be defined. As overflow can be seen either EdGE, that means the analog
output runs on the set limits e.g. 4 mA and 20 mA, or to.OFF (input value smaller than initial
value, analog output changes on e.g. 4 mA), to.End (higher than final value, analog output
changes on e.g. 20 mA). If to.MIn or to.MAX is set, the analog output changes on the smallest or
highest possible binary value. This means that values of e.g. 0 mA, 0 VDC or values higher
than 20 mA or 10 VDC can be reached. With [P] the selection is confirmed and the device
changes into menu level.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–out–“.
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
21
23
5. Setting up the device
5.4.5. Relay functions
Menu group level
Menu level
Menu level
Parameterisation level
Alerting relay 1, rEL-1:
Default: al-1
….
….
Each setpoint (optional) can be linked up via 4 alarms (by default). This can either be inserted
at activated alarms AL1/4 or deactivated alarms ALN1/4. If LOGIC is selected, logical links are
available in the menu level LoG-1 and CoM-1. Access to these two menu levels is via LOGIC, at all
other selected functions, these two parameters are overleaped. Via On/OFF the setpoints can be
activated/deactivated, in this case the output and the setpoint display are set/not set on the
front of the device. The parameters Cal, Cal.of and CAL.en can only be used in accordance with
the semi-automatic calibration (Chapter 8. Sensor alignment). At Cal the relay switches during
sensor calibration, at cal.of during offset calibration and at Cal.en during the calibration of the
final value. With [P] the selection is confirmed and the device changes into menu level.
Logic relay 1, Log-1
Default: or
Here, the switching behavior of the relay is defined via a logic link, the following schema
describes these functions with inclusion of AL-1 and AL-2: This parameter can only be selected if
LOGIC was selected under REl-1 .
A1 v A2
As soon as a selected alarm is activated, the relay
operates. Equates to operating current principle.
A1 v A2 = A1 Λ A2
The relay operates only, if no selected alarm is
active. Equates to quiescent current principle.
A1 Λ a2
The relay operates only, if all selected alarms are
active.
A1 Λ A2 = A1 v A2
As soon as a selected alarm is not activated, the
relay operates.
____ _ _
____ _ _
With [P] the selection is confirmed and the device changes into menu level.
24
22
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
Menu level
Parameterisation level
Alarms for relay 1, CoM-1:
Default: a.1
….
The allocation of the alarms to relay 1 happens via this parameter, one alarm or a group of
alarms can be chosen. This parameter can only be selected if LOGIC was selected under REl-1.
With [P] the selection is confirmed and the device changes into menu level.
Alerting relay 2, reL-2:
Default: al-2
….
….
Each setpoint (optional) can be linked up via 4 alarms (by default). This can either be inserted
at activated alarms AL1/4 or deactivated alarms ALN1/4. If LOGIC is selected, logical links are
available in the menu level LoG-1 and CoM-1. Access to these two menu levels is via LOGIC, at all
other selected functions, these two parameters are overleaped. Via On/OFF the setpoints can be
activated/deactivated, in this case the output and the setpoint display are set/not set on the
front of the device. The parameters Cal, Cal.of and CAL.en can only be used in accordance with
the semi-automatic calibration (Chapter 8. Sensor alignment). At Cal the relay switches during
sensor calibration, at cal.of during offset calibration and at Cal.en during the calibration of the
final value. With [P] the selection is confirmed and the device changes into menu level.
Logic relay 2, LoG-2:
Default: or
Here, the switching behavior of the relay is defined via a logic link, the following schema
describes these functions with inclusion of AL-1 and AL-2: This parameter can only be selected if
LOGIC was selected under REl-1.
A1 v A2
As soon as a selected alarm is activated, the relay
operates. Equates to operating current principle.
A1 v A2 = A1 Λ A2
The relay operates only, if no selected alarm is
active. Equates to quiescent current principle.
A1 Λ a2
The relay operates only, if all selected alarms are
active.
A1 Λ A2 = A1 v A2
As soon as a selected alarm is not activated, the
relay operates.
____ _ _
____ _ _
With [P] the selection is confirmed and the device changes into menu level.
23
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
25
5. Setting up the device
Menu level
Parameterisation level
Alarms for relay 2, CoM-2:
Default: a.2
….
The allocation of the alarms to relay 2 happens via this parameter, one alarm or a group of
alarms can be chosen. This parameter can only be selected if LOGIC was selected under REl-2.
With [P] the selection is confirmed and the device changes into menu level.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–rel–“.
5.4.6. Alarm parameters
Menu group level
Menu level
Menu level
Parameterisation level
Dependency of alarm 1, ALrM.1:
Default: actua
The dependency of alarm 1 can be related to special functions, in detail these are the current
measurand, the min/max-value, the totaliser value/sum value, the sliding average value, the
constant value or the difference between the current measurand and the constant value. If Hold
is selected the alarm is hold and processed just after deactivation of HOLD. EHtEr causes the
dependency either by pressing the [O]-key on the front of the housing or by an external signal
via the digital input. With [P] the selection is confirmed and the device changes into menu level.
Example:
By using the maximum value Alarm.1 = Max.va in combination with a threshold monitoring
Fu-1 = High, an alarm confirmation can be realised. Use the navigation keys or the 4th key for
confirmation.
26
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
24
5. Setting up the device
Menu level
Parameterisation level
Threshold values / limits, LI-1:
Default: 2000
This limit value defines the threshold, that leads to an activation / deactivation of the alarm.
Hysteresis for threshold values, HY-1:
Default: 00000
The difference to the threshold value that causes the delay of the actuation of the alarm, is
defined by the hysteresis.
Function for threshold value exceedance/undercut, Fu-1:
Default: high
The limit value undercut can be selected with Louu (LOW = lower limit value) and limit value
exceedance can be selected with high (HIGH = upper limit value). If e.g. limit value 1 is on a
switching threshold of 100 and occupied with function high, the alarm will be activated by
reaching the threshold. If the limit value is allocated to Low, an alarm will be activated by
undercut of the threshold.
Switching-on delay, ton-1:
Default: 000
For limit value 1 one can preset a delayed switching-on of 0-100 seconds.
Switching-off delay, toF-1:
Default: 000
For limit value 1 one can preset a delayed switching-off of 0-100 seconds.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–Ali–“.
The same applies to –Al2– to –Al4–.
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
25
27
5. Setting up the device
5.4.7. Totaliser (Volume metering)
Menu group level
Menu level
Menu level
Parameterisation level
Totaliser state, total:
Default: off
The totaliser makes measurements on a time base of e.g. l/h possible, at this the scaled input
signal is integrated by a time and steadily (select Stead) or temporarily (select temp) safed.
Choose the quick storage for numerous filling processes and the permanent storage for
consumption measurings. At the permanent storage Stead, the current cumulative value is
safed at each totaliser reset and furthermore, every 30 minutes in the non-volatile memory of
the device. If Off is selected, the function is de-activated. With [P] the selection is confirmed
and the device changes into menu level.
Time base, t.base:
Default: sec
Under this parameter the time base of the measurement can be preset in seconds, minutes or
hours.
Totaliser factor, Facto:
Default: ieo
…
Here the factor (100…106) respectively the divisor for the internal calculation of the measuring
value is assigned.
Setting up the decimal point for the totaliser, tot.dt:
Default: 0
The decimal point of the device can be adjusted with the navigation keys [▲] [▼]. With [P] the
selection is confirmed and the device changes into menu level.
28
26
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
6. Reset to factory settings
Menu level
Parameterisation level
Totaliser reset, tot.re:
Default: 00000
The reset value is adjusted from the smallest to the highest digit with the navigation keys
[▲] [▼] and digit per digit confirmed with [P]. After the last digit, the display switches back to
the menu level. The activator for the reset is parameter driven via the 4th key or via the optional
digital input.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–tot–“.
Programming interlock:
Menu-group level
Description see page 11, menu-level run
6. Reset to factoty settings
To return the unit to a defined basic state, a reset can be carried out to the default values.
The following procedure should be used:
• Switch off the power supply
• Press button [P]
• Switch on voltage supply and press [P]-button until „- - - - -“ is shown in the display.
With reset, the default values of the program table are loaded and used for subsequent operation. This sets
the unit back to the state in which it was supplied.
Caution! All application-related data are lost.
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
27
29
7. Alarms / Relays
7. Alarms / Relays
This device has 4 virtual alarms that can monitor one limit value in regard of an undercut or exceedance.
Each alarm can be allocated to an optional relay output S1-S2; furthermore alarms can be controlled by
events like e.g. hold or min/max-value.
Function principle of alarms / relays
Alarm / Relay x
Deactivated, instantaneous value, min/max-value, hold-value, totaliser
value, sliding average value, constant value, difference between
instantaneous value and constant value or an activation via the digital
input or the [O]-key.
Switching threshold
Threshold / limit value of the change-over
Hysteresis
Broadness of the window between the switching thresholds
Working principle
Operating current / Quiescent current
Operating current
By operating current the alarm S1-S2 is off
below the threshold and on on reaching the
threshold.
Quiescent current
By quiescent current the alarm S1-S2 is on
below the threshold and switched off on
reaching the threshold.
Switching-on delay
The switching-on delay is activated via an
alarm and e.g. switched 10 seconds after
reaching the switching threshold, a shortterm exceedance of the switching value does
not cause an alarm, respectively does not
cause a switching operation of the relay. The
switching-off delay operates in the same
way, keeps the alarm / the relay switched
longer for the parameterised time.
30
28
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
8. Sensor calibration offset / final value
8. Sensor calibration offset / final value
The device is equipped with a semi-automatic sensor calibration (SENSu/SENSa). A switching output operates
the trimming resistor, which exists in some sensors. An adjustment of offset and final value takes place,
after which the sensor can be used directly. Depending on parameterisation, the calibration can be realized
via the 4th key or via the digital input. It is possible to key during the calibration steps. So, reference signals
can be connected manually. However the calibration will be interrupted after 30 seconds.
Press actuator for minimum 3
seconds.
Activate optional switching
output.
For calibration
problems or 30
seconds
holding time.
For minimum 1 measuring cycle,
minimum 1s or maximum per actuator.
Current measuring range value,
e.g. 0.061
For minimum 1 measuring cycle
or with actuator.
Switch-off/switch-on optional
switching output, e.g. 7,132
For minimum 1 measuring cycle,
minimum 1s or maximum per actuator.
Current measuring range value.
For minimum 1 measuring cycle,
minimum 1s or maximum per
actuator.
For calibration
problems or 30
seconds
holding time.
Optional: switch-off switching output and
display for minimum 1 measuring cycle or
minimum 1s holding time.
Back to regular operation mode.
29
Back to regular operation mode,
after 1s or 1 measuring cycle.
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
31
9. Technical data
9. Technical data
Housing
Dimensions
96x48x70 mm (BxHxD)
96x48x89 mm (BxHxD) including plug-in terminal
Panel cut-out
92.0+0.8 x 45.0+0.6 mm
Wall thickness
up to 15 mm
Fixing
screw elements
Material
PC Polycarbonate, black, UL94V-0
Sealing material
EPDM, 65 Shore, black
Protection class
standard IP65 (Front), IP00 (Back side)
Weight
approx. 200 g
Connection
plug-in terminal; wire cross-section up to 2.5 mm2
Display
Digit height
14 mm
Segment colour
red (optional green, orange or blue)
Display range
-19999 up to 99999
Setpoints
one LED per setpoint
Overflow
horizontal bars at the top
Underflow
horizontal bars at the top
Display time
0.1 to 10.0 seconds
Input
Measuring range
Ri
Measuring error
Digit
min. -22…max. 24 mA
0/4 – 20 mA
~100 Ω
0.1 % of measuring range
±1
min. -12…max. 12 VDC
0 – 10 VDC
~200 kΩ
0.1 % of measuring range
±1
Digital input
< 2.4 V OFF, 10 V ON, max. 30 VDC
RI ~ 5 kΩ
Accuracy
32
Temperature drift
100 ppm / K
Measuring time
0.1…10.0 seconds
Measuring principle
U/F-conversion
Resolution
approx. 18 bit at 1s measuring time
30
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
9. Technical data
Output
Sensor supply
24 VDC / 50 mA; 10 VDC / 20 mA
Analog output
0/4-20 mA / burden 350Ohm; 0-10 VDC / burden 10kOhm, 16 bit
Switching outputs
Relay with change-over contacts
Switching cycles
250 VAC / 5 AAC; 30 VDC / 5 ADC
30 x 103 at 5 AAC, 5 ADC ohm resistive burden
10 x 106 mechanically
Diversification according to DIN EN50178 /
Characteristics according to DIN EN60255
Power supply
230 VAC ± 10 % max. 10 VA
10-30 VDC galv. isolated, max. 4 VA
Memory
EEPROM
Data life
≥ 100 years at 25°C
Ambient conditions
Working temperature
0°…50°C
Storing temperature
-20°…80°C
Weathering resistance
relative humidity 0-80% on years average without dew
EMV
EN 61326
CE-sign
Conformity according to directive 2004/108/EG
Safety standard
According to low voltage directive 2006/95/EG
EN 61010; EN 60664-1
31
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
33
10. Safety advices
10. Safety advices
10.
10. Safety
Safety advices
advices
Please
Please read
read the
the following
following safety
safety advice
advice and
and the
the assembly
assembly chapter
chapter 2
2 before
before installation
installation and
and keep
keep it
it
for
future
reference.
for future reference.
Proper
Proper use
use
The DAL-111--device is designed for the evaluation and display of sensor signals.
The M2-11-device
M2-11-device is
is designed
designed for
for the
the evaluation
evaluation and
and display
display of
of sensor
sensor signals.
signals.
The
Danger!
Danger!
Careless use
use or
or improper
improper operation
operation can
can result
result in
in
Careless
personal
injury
and/or
cause
damage
to
the
equipment.
personal injury and/or cause damage to the equipment.
Control of
of the
the device
device
Control
The panel
panel meters
meters are
are checked
checked before
before dispatch
dispatch and
The
and sent
sent out
out in
in perfect
perfect condition.
condition. Should
Should there
there be
be
any
visible
damage,
we
recommend
close
examination
of
the
packaging.
Please
inform
the
any visible damage, we recommend close examination of the packaging. Please inform the
supplier immediately
immediately of
of any
any damage.
damage.
supplier
Installation
Installation
The DAL-111-device
M2-11-device must
must
bebe
installed
byby
a suitably
qualified
The
must
installed
a suitably
qualifiedspecialist
specialist (e.g.
(e.g. with
with a
qualification in
in
The
M2-11-device
be
installed
by
a
suitably
qualified
specialist
(e.g.
with
aa qualification
qualification
in
industrial
electronics).
industrial
industrial electronics).
electronics).
Notes on
on installation
installation
Notes
There must
must be
be no
no magnetic
magnetic or
or electric
electric fields
fields in
in the
the vicinity
vicinity of
of the
the device,
device, e.g.
e.g. due
due to
to
•• There
transformers, mobile
mobile phones
phones or
or electrostatic
electrostatic discharge.
discharge.
transformers,
The fuse
fuse rating
rating of
of the
the supply
supply voltage
voltage should
should not
not exceed
exceed a
a value
value of
of 6A
6A N.B.
N.B. fuse.
fuse.
•• The
Do not
not install
install inductive
inductive consumers
consumers (relays,
(relays, solenoid
solenoid valves
valves etc.)
etc.) near
near the
the device
device and
and
•• Do
suppress
any
interference
with
the
aid
of
RC
spark
extinguishing
combinations
or
free-wheeling
suppress any interference with the aid of RC spark extinguishing combinations or free-wheeling
diodes.
diodes.
Keep input,
input, output
output and
and supply
supply lines
lines separate
separate from
from one
one another
another and
and do
do not
not lay
lay them
them parallel
parallel with
with
•• Keep
each
other.
Position
“go”
and
“return
lines”
next
to
one
another.
Where
possible
use
twisted
pair.
each other. Position “go” and “return lines” next to one another. Where possible use twisted pair.
So, you
you receive
receive best
best measuring
measuring results.
results.
So,
Screen off
off and
and twist
twist sensor
sensor lines.
lines. Do
Do not
not lay
lay current-carrying
current-carrying lines
lines in
in the
the vicinity.
vicinity. Connect
Connect the
the
•• Screen
screening
on
one
side
on
a
suitable
potential
equaliser
(normally
signal
ground).
screening on one side on a suitable potential equaliser (normally signal ground).
The device
device is
is not
not suitable
suitable for
for installation
installation in
in areas
areas where
where there
there is
is a
a risk
risk of
of explosion.
explosion.
•• The
Any electrical
electrical connection
connection deviating
deviating from
from the
the connection
connection diagram
diagram can
can endanger
endanger human
human life
life
•• Any
and/or
can
destroy
the
equipment.
and/or can destroy the equipment.
The terminal
terminal area
area of
of the
the devices
devices is
is part
part of
of the
the service.
service. Here
Here electrostatic
electrostatic discharge
discharge needs
needs to
to be
be
•• The
avoided. Attention!
Attention! High
High voltages
voltages can
can cause
cause dangerous
dangerous body
body currents.
currents.
avoided.
Galvanic isolated
isolated potentials
potentials within
within one
one complex
complex need
need to
to be
be placed
placed on
on an
an appropriate
appropriate point
point
•• Galvanic
(normally
earth
or
machines
ground).
So,
a
lower
disturbance
sensibility
against
impacted
(normally earth or machines ground). So, a lower disturbance sensibility against impacted
energy can
can be
be reached
reached and
and dangerous
dangerous potentials,
potentials, that
that can
can occur
occur on
on long
long lines
lines or
or due
due to
to faulty
faulty
energy
wiring, can
can be
be avoided.
avoided.
wiring,
34
32
32
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
11. Error elimination
11. Error elimination
Error description
Measures
1.
The unit permanently indicates
overflow.
• The input has a very high measurement, check
the measuring circuit.
• With a selected input with a low voltage signal, it
is only connected on one side or the input is open.
• Not all of the activated supporting points are
parameterised. Check if the relevant parameters
are adjusted correctly.
2.
The unit permanently shows
underflow.
• The input has a very low measurement, check the
measuring circuit .
• With a selected input with a low voltage signal, it
is only connected on one side or the input is open.
• Not all of the activated supporting points are
parameterised. Check if the relevant parameters
are adjusted correctly.
3.
The word "HELP " lights up in the
7-segment display.
• The unit has found an error in the configuration
memory. Perform a reset on the default values
and reconfigure the unit according to your
application.
4.
Program numbers for parameterising
of the input are not accessible.
• Programming lock is activated
• Enter correct code
5.
"Err1" lights up in the 7-segment
display
• Please contact the manufacturer if errors of this
kind occur.
6.
The device does not react as
expected.
• If you are not sure that the device has been parameterised before, then follow the steps as written
in chapter 6 and set it back to its delivery status.
33
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
35

Pegel
Druck


Temperatur Durchfluss
Registrierung
Visualisierung
¸



Füllstand



Messumformer
Sensorik
USV
Wir erwarten Ihren Anruf.
ACS-CONTROL-SYSTEM GmbH
Lauterbachstr. 57
D- 84307 Eggenfelden
know how mit System
Ihr Partner für Messtechnik und Automation
¸
[email protected]
www.acs-controlsystem.de
Stand 07/2014
ACS-CONTROL-SYSTEM
Tel: +49 (0) 8721-9668-0
Fax: +49 (0) 8721-9668-30
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement