User Guide

User Guide
Technical Specifications
Power
AC 120V~60Hz or AC 230/240/250V~50Hz
Fuse
20mm Glass 10A Fast Blow
Lamp
MSD 250/2
Dimension
360mm x 397mm x 503mm
Weight
26 kg
I
User Guide
Professional Entertainment Technology
7. Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in which
the fixture operates: damp, smoky or particularly dirty surrounding can cause greater
accumulation of dirt on the unit’s optics.
TABLE OF CONTENTS
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
1. Safety Instruction
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60
days.
2. Technical Specification
2.1 Inserting/Exchanging rotating gobos
2.2 Beam angel
EC Declaration of Conformity
3. Lamp
We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55014-1: 1993, EN61000-3-2: 1995, EN61000-3-3: 1995
EN55014-2: 1997 CATEGORY II
EN61000-4-2: 1995, EN61000-4-3: 1995, EN61000-4-4: 1995
EN61000-4-5: 1995, EN61000-4-6: 1995, EN61000-4-11: 1994
&
Harmonized Standard
4. How To Set The Unit
4.1 Control Panel
4.2 Main Function
2-
-
5. How To Control The Unit
5.1 Master/Slave Built-In Preprogrammed Function.
5.2 Easy Controller
EN60598-1: 1993
Safety of household and similar electrical appliances
Part 1 : General requirem ents
5.3 Universal DMX Controller
5.4 DMX512 Configuration
5.5 DMX512 Connection
Following the provisions of the Low Voltage Directive 73/23/EEC and 93/68/EEC.
6. Troubleshooting
EC Declaration of Conformity
We declare that our products (remote controller) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55015: 1993
EN50082-1: 1997
EN61000-3-2: 1995
EN61000-3-3: 1995
7. Fixture Cleaning
1. Safety Instruction
H. If The IM-7S pan belt is broken
1. Turn off the main power.
Please read carefully the instruction, which includes important
2. Unscrew all the screws (A) and open the base-housing cover (B).
information about the installation, usage and maintenance.
3. Unplug all the connect wires (C) that from the arm to PC board and igniter.
WARNING
4. Unscrew the screws (D) that fix the bridge (E).
♦
Please keep this User Guide for future consultation. If you sell the unit to another
5. Unscrew the screws (F) that fix the axis gear (G).
user, be sure that they also receive this instruction booklet.
6. Change a new belt (H) by going through all connecting wires that from the arm to base,
♦
Unpack and check carefully there is no transportation damage before using the unit.
♦
Before operating, ensure that the voltage and frequency of power supply match the
7. Set up the gear axis to the bridge and screwed it. Note: do not press the belt.
and through the bridge for correct position.
power requirements of the unit.
8. Put the belt around the axis gear and motor gear.
♦
The unit is designed for use with the MSD 250/2 . Do not use any other type of lamp.
9. Plug all the connect wires (C) that form the arm to PC board and igniter.
♦
It’s important to ground the yellow/green conductor to earth in order to avoid electric
10. Adjust the pan home position.
shock.
11.Screw the base-housing cover (B).
♦
The unit is for indoor use only. Use only in a dry location.
♦
The unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces. Be sure that no ventilation slots are b locked.
♦
Disconnect main power before fuse/lamp replacement or servicing.
♦
Replace fuse/lamp only with the same type.
♦
Make sure there are no flammable materials close to the unit while operating, as it
3-
-
is fire hazard.
♦
G
Use safety chain when fixes this unit. D on’t handle the unit by taking its head only,
H
but always by taking its base.
♦
Maximum ambient temperature is Ta : 40 ? . Don’t operate it where the temperature
A
E
C
is higher than this.
♦
D
D
B
Unit surface temperature may reach up to 85? . Don’t touch the housing bare-hand
during its operation, and allow about 15 minutes to cool down before replacing bulb
F
or serving, as the unit could be very hot.
♦
In the event of serious operating problem, stop using the unit immediately. Never try
to repair the unit by yourself. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical a ssistance
B
A
center. Always use the same type spare parts.
♦
Don’t connect the device to any dimmer pack.
♦
Do not touch any wire during operation as high voltage might be causing electric
shock.
A
.
Pay attention to the belt tension when install the belt.
Please refer to the photos below:
Warning
♦ To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
♦ Never touch bulb with bare fingers as it is very hot after using.
♦ Hot lamp explosion hazard. Do not open the unit within five minutes after switching off.
♦ Do not start on the unit without bulb enclosure or housing are damaged.
♦ The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
♦ Do not look directly at the light while the bulb is on.
Caution
There are no user serviceable parts inside the unit. Do not open the housing or attempt
any repairs yourself. In the unlikely event your unit may require service, please contact
Photo 1
your nearest dealer.
4-
-
Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit
is firmly fixed to avoid vibration and slipping while operating. Always ensure that the
structure to which you are attaching the unit is secure and is able to support a weight of 30
kgs for each unit
Photo 2
2. Technical Specification
G. If The IM-8S pan belt is broken
Power supply
1. Turn off the main power.
- AC 120V~60Hz or 230V/240V/250V 50/60Hz
2. Unscrew all the screws (A) and open the base-housing cover (B).
- AC 120V 60Hz / 230V 50Hz
3. Unplug all the connect wires (C) that from the arm to PC board and igniter.
Lamp
4. Unscrew the screws (D) that fix the bridge (E).
- Discharge lamp MSD 250/2 GY 9.5(IM-8S)
5. Unscrew the screws (F) that fix the axis gear (G).
- Discharge NSD HTI 150W GY 9.5 (IM-7S)
6. Change a new belt (H) by going through all connecting wires that from the arm to base,
Optical system
and through the bridge for correct position.
- Standard 13° focused beam angle.
7. Set up the gear axis to the bridge and screwed it. Note: do not press the belt.
- Focus adjustable by DMX control.
8. Put the belt around the axis gear and motor gear.
Shutter/Dimmer
9. Plug all the connect wires (C) that form the arm to PC board and igniter.
- Blackout, 0~100 smooth dimming and strobe speed variable(1~10 flashes per second).
10. Adjust the pan home position.
Gobo wheel
11.Screw the base-housing cover (B).
- Independent gobo wheel with 7 gobos plus open, gobos are interchangeable: 4 metal
gobos, 2 glass gobos, and 1 effect gobo.
- Gobo wheel rotates with variable speed, giving shaking effect.
Color wheel
- Independent color wheel with 9 dichroic mirrors plus white.
- Color wheel rotates with variable speed, giving rainbow effect.
Movement
- Pan: 540° in 2.8 second.
- Tilt: 270° in 1.6 second.
DMX Channels
- Standard DMX512 signal addressing and can be controlled by any universal DMX controller.
IM-8S
IM-7S
Channel 1
Pan motion
Pan motion
Channel 2
Tilt motion
Tilt motion
Channel 3
Shutter/ Shaking
Shutter/ Shaking
Channel 4
Gobo
Gobo
Channel 5
Color
Color
Channel 6
Gobo Rotation
Gobo Rotation
Channel 7
Dimmer
Dimmer
Channel 8
Focus
Dimension: 360mm x 397mm x 503mm (IM-8S)
373mm x 295mm x 451 mm(IM-7S)
Weight: 26 kg(IM-8S)
13 kg(IM-7S)
5-
-
6. Troubleshooting
2.1 Inserting/Exchanging rotating gobos
Following are a few common problems that may occur during operation. Here are
DANGER!
Install the gobos with the device switched off only.
Unplug from mains before changing gobos!
some suggestions for easy troubleshooting:
A. The unit does not work, no light and the fan does not work
Open the cover by loosening the fastening screw at the sides of the cover.
1. Check the connect power and main fuse.
If you wish to use other forms and patterns as the standard-gobos, or if the gobos are to be
2. Measure the mains voltage on the main connector.
exchanged, remove the fixation ring with an appropriate tool. Remove the gobo and insert the
3. Check the power on LED.
new gobo. Press the fixation-ring together and ins ert it in the front of the gobo.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
of the unit or the previous one.
4. Try to use another DMX controller.
5. Check in the DMX cables run near or run alongside to high voltage cables that may
cause damage or interference to DMX interface circuit.
C. Some units don’t respond to the easy controller
6-
-
1. You may have a break in the DMX cabling. Check the LED for the response of the
master/ slave mode signal.
2. Wrong DMX address in the unit. Set the proper address.
D. No response to the sound
CAUTION!
Never unscrew the screws of the rotating gobo as the ball bearing
will otherwise be opened!
1. Check the unit that is not receiving DMX signal.
2. Check microphone to see if it is good by tapping the microphone
E. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.
F. The lamp is cutting out intermittently
1. The lamp is not working well. Check the main voltage either too high or too low.
2. Internal temperature may be too high. Check and if necessary replace the fan on the
head.
2.2 Beam angel
3. Lamp
5.5 DMX512 Connection
The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.
In case of replacement of the lamp or maintenance, do not open the
fixture within 15 minutes until the unit cools down after switching off.
Because of its high internal pressure, there might be a risk that the Discharge lamp
would explode during operation. The lamp emits intense UV radiation which is harmful to
the eyes and skin. The high luminance of the arc can cause severe damage to the retina
if looks directly at the lamp.
Discharge lamp : MSD 250/2(IM-8S
NSD HTI 150W(IM-7S)
1. Always switch off the main supply and never handle
the lamp or luminaries when is hot.
2. Do not touch the bulb with bare hands. If this
happens, clean the lamp with denatured alcohol and
wipe it with a lint free cloth before installation.
3. The lamp generates UV radiation. Never operate the
lamp without appropriate shielding.
4. When burning, the lamp operates at high pressure and
there is a slight risk of arc tube rupture. The risk
increases with age, temperature and improper handling
of the lamp. Do not use the lamp any longer than its
specified life.
5. Make sure the lamp is located in the center of the
reflector for the best spot. Adjust lamp position by
screws A, B and C.
7-
-
1. If you use a controller with 5 pins DMX connector, you need to use a 5 to 3 pin adapter.
2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120-ohm 1/4W
resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the
DMX-output of the last unit.
3. Connect the unit together in a “daisy chain” by XLR plug from the output of the unit to the
input of the next unit. The cable can not branched or split to a “Y” cable. DMX512 is a very
high-speed signal. Inadequate or damaged cables, soldered joints or corroded connectors
can easily distort the signal and shut down the system.
4. The DMX output and input connectors are pass-through to maintain the DMX circuit, when
power is disconnected to the unit.
5. Each lighting unit needs to have an address set to receive the data sent by the controller.
The address number is between 0-511 (usually 0 & 1 are equal to 1).
6. The end of the DMX512 system should be terminated to reduce signal errors.
7. 3 pin XLR connectors are more popular than 5 pins XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5.4 DMX512 Configuration
4. How To Set The Unit
4.1 Control Panel
Display
To show the various menus and the selected functions.
LED
8-
-
DMX
MASTER
SLAVE
SOUND
On
On
On
Flashing
DMX input present
Master Mode
Slave Mode
Sound activation
MENU
DOWN
UP
ENTER
To select the programming functions
To go backward in the selected functions
To go forward in the selected functions
To confirm the selected functions
Button
Remote controller input
By connect to the 1/4” microphone jack to control the unit for Stand by, Function and Mode
Sensitivity
To adjust the sensitivity for microphone receiving.
Microphone
To receive audio signal for sound activation.
DMX input/output
For DMX512 link, use 3-pin XLR plug cable to link the unit together.
IM-7S without focus channel.
4.2 Main Function
5.2 Easy Controller
To select any of the pre-set functions, press the MENU button up to when the required one is
The easy remote controller is used only in master/slave mode. By
shown on the display. Select the function by ENTER button and the display will blink. Use
connecting to the 1/4” microphone jack of the first unit, you will find
DOWN and UP button to change the mode. Once the required mode has been selected,
that the remote control on the first unit will control all the other units
press the ENTER button to setup or it will automatically return to the main functions without
for Stand by, Function and Mode.
any change after idling 8 seconds. To go back to the functions without any change press the
MENU button. The main functions are shown below:
Stand by Blackout the unit
Strobe
1.Gobo/Color sync.
Function
strobe
2.Sync. strobe
3.Two-light strobe
Mode
Sound 1
(LED off )
X/Y moving pattern
selection
( 12 patterns )
Color/Gobo selection
1. Hold on for gobo
change.
2. Press shortly for
color change.
Sound 2
Slow/Sound 3
(LED normal blinking) (LED on)
X/Y moving setting
1.Pan position
2.Tilt position
3.Dimmer
Position/ Latch
(LED fast blinking)
9-
-
5.3 DMX Controller
If you use a universal DMX controller to control the units, you have to set DMX address from
1 to 512 channel so that the units can receive DMX signal.
Press the MENU button up to when the
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press and keep ENTER button pressed up to when the
display stops blinking or storing automatically 8 seconds later. To go back to the functions
without any change press the MENU button again. Please refer to the following diagram to
address your DMX512 channel for the first 4 units.
DMX address can be setting remotely by IL-0824 controller. No need to calculate the DMX
channels of each fixture in the chain.
5. How To Control The Unit
DMX512 Address Setting
You can operate the unit in three ways:
1. By master/slave built-in preprogram function
Press the MENU button up to when the
is show ing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
2. By easy controller
Once the address has been selected, press the ENTER button to setup or automatically
3. By universal DMX controller
return to the main functions without any change after 8 seconds. To go back to the functions
without any change press the MENU button again.
No need to turn the unit off when you change the DMX address, as new DMX address setting
will be effected at once. Every time you turn the unit on, it will show IM8S / IM-7S on the
Show Mode
display and move all the motors to their ‘home’ position and you may hear some noises for
about 20 seconds. After that the unit will be ready to receive DMX signal or run the built-in
Press the MENU button up to when the
programs.
button and the display will blink. Use DOWN and UP button to select the
is showing on the display. Pressing ENTER
(show 1) or
(show 2) or
(show 3) or
(show 4) mode. Once the mode has been
selected, press the ENTER button to setup or automatically return to the main functions
5.1 Master/Slave Built-In Preprogrammed Function
without any change after 8 seconds. To go back to the functions without any change press
the MENU button again.
You can select blackout mode
in
(yes blackout) or
(no blackout)
mode while the unit is turned on. By linking the units in master/slave connection, the first unit
10-
will control the other units to give an automatic, sound activated, synchronized light show.
This function is good when you want an instant show. You have to select
-
(show 1) or
(show 2) or
(show 3) or
(show 4) mode by easy controller. Its
DMX input jack will have nothing plugged into it, and Its master LED will be constantly on and
sound LED will flash to the music. The other units will have to set in slave mode
and
select
(normal) or
(2 light show) mode, Their DMX cables plugged into the
DMX input jacks (daisy chain) and the slave LED lights will constantly on.
Show 1 mode - Fixture is placed on the floor. Tilt movement angle 210°.
Show 2 mode - Fixture is fixed under ceiling. Tilt movement angle 90°.
Show 3 mode - Fixture is placed on the floor, Pan/Tilt movement in front,
Pan movement angel 160°,Tilt movement angel 90°.
Show 4 mode - Fixture is fixed on the floor, Pan/Tilt movement in top.
Pan movement angel 160°,Tilt movement angel 90°.
Slave Mode
2-light show
Press the MENU button up to when the
In
(slave mode),
means the unit works normally and
2-light show. In order to create a great light show, you can set
get contrast movement to each other, even if you have two units only.
means
on the second unit to
is show ing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
(normal) or
(2 light show) mode. Once the mode has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8 seconds. To go
back to the functions without any change press the MENU button again.
Blackout Mode
Press the MENU button up to when the
Display Inversion
It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to
is show ing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
(yes
when the
blackout) or
(no blackout) mode. Once the mode has been selected, press the
ENTER button to setup or automatically return to the main functions without any change after
is blinking on the display. Use the ENTER button to change to the mode
(display inversion), It will automatically store after 8 seconds. Or press the ENTER
button again return to the mode
the MENU button.
8 seconds. To go back to the functions without any change press the MENU button again.
(display normal). To go back to the functions press
Display normal mode for the fixture putting on the floor.
Color Mode
Press the MENU button up to when the
Display inversion mode for the fixture fixing under ceiling.
is show ing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
Focus Adjust
(normal) or
(split color) mode. Once the mode has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8 seconds. To go
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button, the unit will focus on tilt 90°, and then the unit will focus on pan 0°, pan 90°, pan180°,
back to the functions without any change press the MENU button again.
pan270° in every pressing ENTER button. Use DOWN and UP button to adjust focus. To go
back to the functions press the MENU button again.
Pan Inversion
Press the MENU button up to when the
Self-Test
is show ing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
(normal) or
(pan inversion) mode. Once the mode has been selected, press the ENTER button
to setup or automatically return to the main functions without any change after 8 seconds. To
11-
-
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button and the unit will run self-test by built-in program. To go back to the functions press the
MENU button again.
go back to the functions without any change press the MENU button again.
Fixture Hours
Tilt Inversion
Press the MENU button up to when the
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
(normal) or
(tilt inversion) mode. Once the mode has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8 seconds. To go
back to the functions without any change press the MENU button again.
functions press the MENU button again.
Reset
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button and all channels of the unit will return to their standard position. To go back to the
Led Display
Press the MENU button up to when the
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button and the display will show the number of working hours of the unit. To go back to the
functions press the MENU button again.
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
(Led on) or
(Led off) mode. Once the mode has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8 seconds. To go
back to the functions without any change press the MENU button again.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement