Operating Instructions - ACS-CONTROL
User manual M3
Potentiometer > 1 kΩ…< 1000 kΩ
User manual M3
Operating Instructions
Potentiometer > 1 kΩ…< 1000 kΩ
DAL-311x6x0S
Potentiometer > 1kΩ…< 1000 kΩ
Technical features:
• red display of -19999…99999 digits (optional: green, orange, blue)
• installation: 120 mm without plug-in terminal
Technical features:
• min/max-memory
• 30 adjustable setpoints
•• red
display
of -19999…99999
digitsexceedance
(optional: green,
orange,
blue)
display
flashing
at threshold value
/ threshold
value
undercut
•• installation:
120
mm
without
plug-in
terminal
zero-key for triggering of Hold, Tara
•• min/max-memory
permanent min/max-value recording
•• 30
adjustable
setpoints
volume
metering
(totaliser)
•• display
flashing
at threshold
value exceedance
/ threshold
value undercut
mathematic functions
like reciprocal
value, square
root, squaring
or rounding
•• zero-key
for
triggering
of
Hold,
Tara
setpoint generator
•• permanent
min/max-value
recording
sliding average
determination
•• volume
metering
(totaliser)
brightness control
•• mathematic
functions
value, square root, squaring or rounding
programming
interlocklike
viareciprocal
access code
•• setpoint
generator
protection class IP65 at the front side
•• sliding
determination
plug-inaverage
screw terminal
•• brightness
control isolated digital input
optional: galvanic
•• programming
interlock
access code
optional: 1 or 2
analog via
outputs
•• protection
IP65 outputs
at the front
optional: 2class
or 4 relay
or 8side
PhotoMos outputs
•• plug-in
screw
terminal
optional: RS232 or RS485 interface
•• optional:
galvanicPC-based
isolated digital
input
accessories:
configuration-kit
PM-TOOL with CD & USB-adapter for devices without
• optional: 1 or 2 analog
keypadoutputs
and for a simple adjustment of standard devices
• optional: 2 or 4 relay outputs or 8 PhotoMos outputs
• optional: RS232 or RS485 interface
• accessories: PC-based configuration-kit PM-TOOL with CD & USB-adapter for devices without
keypad and for a simple adjustment of standard devices
M3_15GB.pdf update: 21.04.2015
96x48
Order code
Note
1)
sensor supply
only at 0/4...20 mA,
0...10V DC input
DAL-311
2
0
2
3
4
Y
power supply
100-240V AC
10...40V DC galvanic seperated
100-240V AC with sensor supply 24V DC/50mA and digital input 1)
10...40V DC galvanic seperated with sensor supply 24V DC/50mA and digital input
other voltages
6
function input
potentiometer measurement > 1 kOhm up to < 1000kOhm
A
B
C
D
E
Y
function output
0
6
1)
display + 2 relay outputs (changeover)
display + 4 relay outputs
display with analog output 0-10V/4-20mA, switchable
display + 2 relay with analog output 0-10V/4-20mA, switchable
display + 4 relay with analog output 0-10V/4-20mA, switchable
others outputs
standard configuration
S
0
standard, protection IP65
S
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
Contents
1.
Brief description
2
2.
Assembly
3
3.
Electrical connection
4
4.
Description of function and operation
5
4.1. Programming software PM-TOOL
6
Setting up the device
7
5.1. Switching on
7
5.2. Standard parameterisation (flat operation level)
7
5.
Value assignment for the triggering of the signal input
5.3. Programming interlock „RUN“
9
Activation/Deactivation of the programming interlock or change into
professional or flat operation level
5.4. Extended parametersation (professional operation level)
5.4.1. Signal input parameters „INP“
10
10
Value assignment for the triggering of the signal input incl. linearisation
5.4.2. General device parameters „FCT“
13
Superior device functions like Hold, Tara, min/max permanent, setpoint value function /
nominal value function, averaging, brightness control, as well as the control of the digital input and
keyboard layout
5.4.3. Safety parameters „COD“
17
Assignment of user and master code to lock or to receive access to defined parameter such as
analog output and alarms, etc
5.4.4. Serial parameters „ser“
18
Parameter for interface definition
5.4.5. Analog parameters „Out“ and „ou2“
19
Analog outpur functions
5.4.6. Relay functions „rel“
22
Parameter for setpoint definition
5.4.7. Alarm parameters „AL1…AL4“
24
Actuator and dependencies of the alarms
5.4.8. Totaliser (Volume metering) „tot“
26
Parameter for calculation of the sum function
6.
Reset to factory settings
27
Reset parameters onto the delivery state
7.
Alarms / Relays
28
Functional principle of the switching outputs
8.
Interfaces
29
Connection RS232 and RS485
9.
Sensor aligment
30
Diagram of functional sequences for sensors with existing adjustable resistor
10.
Technical data
31
11.
Safety advices
33
12.
Error elimination
34
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden
l www.acs-controlsystem.de l [email protected]
1
3
1. Brief description
1. Brief description
The panel
panelmeter
meterinstrument
M3-15 is DAL-311
a 5-digit isdevice
for device
potentiometer
values of values
>1kΩ of
to >1kΩ
<1000kΩ
and a visual
The
a 5-digit
for potentiometer
to <1000kΩ
and a
threshold
value
monitoring
via
the
display.
The
configuration
happens
via
four
front
keys
or
via
the
visual threshold value monitoring via the display. The configuration happens via 4 keys at the front
oroptional
via the
PC software
PM-TOOL.
An integrated
programming
interlockinterlock
prevents
unrequested
changes
of the of
paraoptional
PC software
PM-TOOL.
The integrated
programming
prevents
unrequested
changes
meters
and
can
be
unlocked
again
by
an
individual
code.
Optional
the
following
functions
are
available:
a
parameters and can be unlocked again with an individual code. Optional the following functions are
supply
for
the
sensor,
a
digital
input
for
triggering
of
Hold
(Tara)
or
two
analog
outputs
for
further
processing
available: a supply for the sensor, a digital input for triggering of Hold (Tara), two analog outputs and
in the equipment.
interfaces
for further evaluating in the unit.
By use
values
can
be controlled
With
helpofofthe
thegalvanic
galvanicisolated
isolatedsetpoints
setpoints(optional),
(optional),free
freeadjustable
adjustablethreshold
limit values
can be
controlled
and and
reported
to
a
superior
master
display.
reported to a superior master display.
Theelectrical
electricalconnection
connection isis done
carried
on the
back side
terminals.
The
viaout
plug-in
terminals
onvia
theplug-in
back side.
Selectable
functions
like
e.g.
the
request
of
the
min/max-value,
an
averageofdetermination
the measuring
Selectable functions like e.g. the recall of the min/max-value, an averaging
the measuringofsignals,
a
signals,
a
nominal
preset
respectively
setpoint
preset,
a
direct
change
of
threshold
value
in
operation
nominal presetting or setpoint presetting, a direct threshold value regulation during operation mode andmode
and additional
measuring
points for
linearisation
complete
the modern
further
measuring
setpointssupporting
for linearisation,
complete
the modern
device
concept.device concept.
4
2
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
2. Assembly
2. Assembly
Please read the Safety advices on page 33 before installation and keep this user manual for future reference.
M3
48,0
3,0
Se
alin
g
9,0
13
Gap for physical unit
1.
2.
3.
After removing the fixing elements, insert the device.
Check the seal to make sure it fits securely.
Click the fixing elements back into place and tighten the clamping screws by hand. Then use a
screwdriver to tighten them another half a turn.
CAUTION! The torque should not exceed 0.1 Nm!
The dimension symbols can be exchanged before installation via a channel on the side!
3
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5
3. Electrical connection
3. Electrical connection
Type DAL-311x6x0S
M3-1VR5B.0005.W70BD with a supply of 10-40 VDC galv. isolated, 18-30 VDC
Type
Type
M3-1VR5B.0005.S70BD with a supply of 100-240 VAC, DC ±10%
Type DAL-311x6x0S
DAL-311x6x0S with digital input and external
voltage source
6
4
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
4. Description of function and operation
4. Description of function and operation
Operation
The operation is divided into three different levels.
Menu level (delivery status)
This level was designed for the standard settings of the device. Only menu items which are sufficent to set
the device into operation are displayed. To get into the professional level, run through the menu level and
parameterise prof under menu item RUN.
Menu group level (complete function volume)
Suited for complex applications as e.g. linkage of alarms, setpoint treatment, totaliser function etc. In this
level function groups which allow an extended parameterisation of the standard settings are availabe. To
leave the menu group level, run through this level and parameterise uloc under menu item RUN.
Parameterisation level:
Parameters deposited in the menu item can here be parameterised. Functions, that can be changed or
adjusted, are always signalised by a flashing of the display. Settings that are made in the parameterisation
level are confirmed with [P] and thus saved. Pressing the [O]-key („zero-key“) leads to a break-off of the
value input and to a change into the menu level. All adjustments are saved automatically by the device and
changes into operating mode, if no further key operation is done within the next 10 seconds.
Level
Key
Description
Change to parameterisation level and deposited values.
Menu level
Keys for up and down navigation in the menu level.
Change into operation mode.
Parameterisation
level
To confirm the changes made at the parameterisation
level.
Adjustment of the value / the setting.
Change into menu level or break-off in value input.
Change to menu level.
Menu group level
Keys for up and down navigation in the menu group level.
Change into operation mode or back into menu level.
5
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
7
4. Description of function and operation
Function chart:
4.1 Parameterisation software PM-TOOL:
Part of the PM-TOOL are the software on CD and an USB-cable with device adapter. The connection is
done via a 4-pole micromatch-plug on the back side of the device, to the PC-side the connection ist done via
an USB plug.
System requirements: PC incl. USB interface
Software: Windows XP, Windows VISTA
With this tool the device configuration can be generated, omitted and saved on the PC. The parameters can
be changed via the easy to handle program surface, whereat the operating mode and the possible selection
options can be preset by the program.
8
6
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
5. Setting up the device
5.1. Switching on
Once the installation is complete, start the device by applying the voltage supply. Before, check once again
that all electrical connections are correct.
Starting sequence
For 1 second during the switching-on process, the segment test (8 8 8 8 8) is displayed followed by an
indication of the software type and, after that, also for 1 second the software version. After the starting
sequence, the device switches to operation/display mode.
5.2. Standard parameterisation (Flat operation level)
To parameterise the display, press the [P]-key in operating mode for 1 second. The display then changes to
the menu level with the first menu item TYPE.
Menu level
Parameterisation level
Selection of the input signal, tYPE:
Default: sens
Potentiometer values from >1 to <1000 kΩ are available as works calibration (without
application of the sensor signal) and as sensor calibration (with applied measuring signal).
Confirm the selection with [P] and the display switches back to menu level.
Setting the end value of the measuring range, END :
Default: 10000
Set the end value from the smallest to the highest digit with [▲] [▼] and confirm each digit with
[P]. A minus sign can only be parameterized on the highest value digit. After the last digit, the
display switches back to the menu level. If Sens was selected as input option, you can only
select between noca and cal. With noca, only the previously set display value is taken over, and
with cal, the device takes over both the display value and the analogue input value
Setting the start/offset value of the measuring range, offs:
Default: 0
Enter the start/offset value from the smallest to the highest digit with [▲] [▼] and confirm each
digit with [P]. After the last digit the display switches back to the menu level. If Sens was
selected as input option, you can only select between noca and cal. With noca, only the
previously set display value is taken over, and with cal, the device takes over both the display
value and the analogue input value.
Setting the decimal point, dot:
Default: 0
The decimal point on the display can be moved with [▲] [▼] and confirmed with [P]. The
display then switches back to the menu level again.
7
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
9
5. Setting up the device
Menu level
Parameterisation level
Setting up the display time, SEC:
Default: 1.0
then
The display time is set with [▲] [▼]. The display moves up in increments of 0.1 up to 1 second
and in increments of 1.0 up to 10.0 seconds. Confirm the selection by pressing the [P] button.
The display then switches back to the menu level again.
Selection of analog output, Out.rA:
Default: 4-20
Three output signals are available: 0-10 VDC, 0-20 mA and 4-20 mA, with this function, the
demanded signal is selected.
Setting up the final value of the analog output, Out.En:
Default: 10000
The final value is adjusted from the smallest digit to the highest digit with [▲] [▼] and digit by
digit confirmed with [P]. A minus sign can only be parameterised on the highest digit. After the
last digit, the device changes back into menu level.
Setting up the initial value of the analog output, Out.OF:
Default: 00000
The final value is adjusted from the smallest digit to the highest digit with [▲] [▼] and digit by
digit confirmed with [P]. A minus sign can only be parameterised on the highest digit. After the
last digit, the device changes back into menu level.
Threshold values / limits, LI-1:
Default: 2000
This value defines the threshold, that activates/deactivates an alarm.
Hysteresis for limit values, HY-1:
Default: 00000
The delayed reaction of the alarm is the difference to the threshold value, which is defined by
the hysteresis.
8
10
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
Menu level
Parameterisation level
Function for threshold value undercut / exceedance, Fu-1:
Default: high
A limit value undercut is selected with Louu (for LOW = lower limit value), a limit value
exceedance with High (for HIGH = higher limit value). If e.g. limit value 1 is on a threshold level
of 100 and allocated with function High, an alarm is activated by reaching of threshold level. If
the threshold value was allocated to Low, an alarm will be activated by undercutting the
threshold value, as long as the hysteresis is zero.
The same applies to Li-1 to LI-2 !
User code (4-digit number-combination, free available), U.CodE:
Default: 0000
If this code was set (>0000), all parameters are locked for the user, if LOC has been selected
before under menu item run. By pressing [P] for 3 seconds in operation mode, the display
shows COde. The U.Code needs to be entered to get to the reduced number of parameter sets.
The code has to be entered befor each parameterisation, until the A.Code (Master code) unlocks
all parameters again.
Master code (4-digit number-combination, free available), A.CodE:
Default: 1234
All parameters can be unlocked with this code, after LOC has been activated under menu item
run. By pressing [P] for 3 seconds in operation mode, the display shows COde and enables the
user to reach all parameters by entering the A.codE. Under run the parameterisation can be
activated permanently by selecting ULOC or ProF, thus at an anew pushing of [P] in operation
mode, the code needs not to be entered again.
5.3. Programming interlock „run“
Activation / deactivation of the programming lock or completion of the standard
parameterisation with change into menu group level (complete function range), run:
Default: uloc
With the navigation keys [▲] [▼], choose between the deactivated key lock Uloc (works
setting) and the activated key lock Loc, or the change into the menu group level ProF. Confirm
the selection with [P]. After this, the display confirms the settings with "- - - - -", and switches
automatically to operating mode. If Loc was selected, the keyboard is locked. To get back into
the menu level, press [P] for 3 seconds in operating mode. Now enter the CODE (works setting
1 2 3 4) that appears using [▲] [▼] plus [P] to unlock the keyboard. FAIL appears if the input is
wrong. To parameterise further functions ProF needs to be set. The device confirms this setting
with „- - - - -„ and changes automatically in operation mode. By pressing [P] for approx. 3
seconds in operation mode, the first menu group InP is shown in the display and thus confirms
the change into the extended parameterisation. It stays activated as long as ULOC or LOC is
entered in menu group RUN.
9
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
11
5. Setting up the device
5.4. Extended parameterisation (Professional operation level)
5.4.1. Signal input parameters
Menu group level
Menu level
Menu level
Parameterisation level
Selection of the input signal, tYPE:
Default: sens
Potentiometer values from >1 to <1000 kΩ are available as works calibration (without
application of the sensor signal) and as sensor calibration (with applied measuring signal).
Confirm the selection with [P] and the display switches back to menu level.
Setting the end value of the measuring range, END:
Default: 10000
Set the end value from the smallest to the highest digit with [▲] [▼] and confirm each digit with
[P]. A minus sign can only be parameterized on the highest value digit. After the last digit, the
display switches back to the menu level. If Sens was selected as input option, you can only
select between noca and cal. With noca, only the previously set display value is taken over, and
with cal, the device takes over both the display value and the analogue input value
Setting the start/offset value of the measuring range, offs:
Default: 0
Enter the start/offset value from the smallest to the highest digit with [▲] [▼] and confirm each
digit with [P]. After the last digit the display switches back to the menu level. If Sens was
selected as input option, you can only select between noca and cal. With noca, only the
previously set display value is taken over, and with cal, the device takes over both the display
value and the analogue input value.
Setting the comma, decimal point, dot:
Default: 0
The decimal point on the display can be moved with [▲] [▼] and confirmed with [P]. The
display then switches back to the menu level again.
12
10
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
Menu level
Parameterisation level
Setting up the display time, SEC:
Default: 1.0
then
The display time is set with [▲] [▼]. The display moves up in increments of 0.1 up to 1 second
and in increments of 1.0 up to 10.0 seconds. Confirm the selection by pressing the [P] button.
The display then switches back to the menu level again.
Rescaling the measuring input values, EndA:
Default: 10000
With this function, you can rescale the input value of e.g. 9.5 kΩ (works setting) without
applying a measuring signal.
Rescaling the measuring input values, OFFA:
Default: 0
With this function, you can rescale the input value of e.g. 1.5 kΩ (works setting) without
applying a measuring signal.
Setting up the tare/offset value, tArA:
Default: 0
The given value is added to the linearized value. In this way, the characteristic line can be
shifted by the selected amount.
Setting up the balance point, Adj.pt:
Default: 08000
The balance point for the final value can be chosen (in %) from the measuring range by Sense.
The preset 80.000% result from the widespread detuning of the melt pressure sensors. The
ADJ.PT is only used by the sensor alignment SE.Cal.
Setting up the physical unit, UnIt:
Default: no
One can choose between the above shown physical units. It will be displayed on the 5th digit of
the display.
11
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
13
5. Setting up the device
Menu level
Parameterisation level
Number of additional setpoints, SPCt:
Default: 00
30 additional setpoints can be defined to the initial value and final value, so linear sensor
values are not linearised. Only activated setpoint parameters are displayed.
Display values for setpoints, dIS.01 … dIS.30:
Under this parameter setpoints are defined according to their value. At the sensor calibration,
like at final value/offset, one is asked at the end if a calibration shall be activated.
Analog values for setpoints, InP.01 … InP.30:
The setpoints are always preset according to the selected input signal mA/V. The demanded
analog values can be freely adjusted in ascending order.
Device undercut, dI.Und:
Default: -i9999
With this function the device undercut (_ _ _ _ _) can be defined on a definite value.
Display overflow, dI.OUE:
Default: 99999
_____
With this function the display overflow (
) can be defined on a definite value.
Input variable of process value, SIG.in:
Default: a.meas
With this parameter, the device can be controlled via the analog input signals a.meas = 10 VAC,
50 VAC respectively 1.5 AAC or via the digital signals of the interface M.bus = RS232/RS485
(Modbus protocol). With [P] the selection is confirmed and the device changes into menu level.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–INP–“.
12
14
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
5.4.2. General device parameters
Menu group level
Menu level
Menu level
Parameterisation level
Display time, DISEC:
Default: 01.0
then
The display time is set up with [▲] [▼]. Thereby you switch up to 1 second in steps of 0.1 and
up to 10.0 seconds in steps of 1.0. With [P] the selection is confirmed and the device changes
into menu level.
Rounding of display values, round:
Default: 00001
This function is for instable display values, where the display value is changed in steps of 1, 5,
10 or 50. This does not affect the resolution of the optional outputs. With [P] the selection is
confirmed and the device changes into menu level.
Arithmetics, ArItH:
Default: no
Reciprocal
Root extraction
Square
With this function the calculated value, not the measuring value, is shown in the display. With
no, no calculation will be deposited. With [P] the selection is confirmed and the device changes
into menu level.
Sliding average determination, AVG:
Default: 10
Under this menu item, the number of measurements that need to be averaged are preset. The
averaging time results from the product of measuring time SEC and the averaged measurements
AVG. With selection of AVG in menu level DISPL the result is shown in the display and evaluated
when entered in the alarm AL1-Al4 or the analog output Outpt.
Zero point slowdown, ZErO:
Default: 00
At the zero point slowdown, a value range around the zero point can be preset, so the display
shows a zero. If e.g.10 is set, the display would show a zero in the value range from -10 to +10;
below continue with -11 and beyond with +11. The maximum adjustable range of value is 99.
13
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
15
5. Setting up the device
Menu level
Parameterisation level
Solid contstant value, const:
Default: 0
The constant value can be evaluated like the current measurand via the alarms or the analog
output. The decimal place cannot be changed for this value and is taken over from the current
measurand. So, with this value a setpoint generator can be realised via the analog output.
Furthermore it can be used as calculated difference. At this the constant value needs to be
subtracted from the current measurand and the difference is evaluated in the alerting or via the
analog output. Thus regulation can be displayed quite easy with this parameterisation.
Minimum constant value, con.mi:
Default: -i9999
The minimum constant value is selected and adjusted from the smallest to the highest digit with
[▲] [▼] and confirmed digit per digit with [P]. A minus sign can only be adjusted on the highest
digit. After the last digit the display changes back into menu level.
Maximum constant value, con.ma:
Default: 99999
The maximum constant value is selected and adjusted from the smallest to the highest digit
with [▲] [▼] and confirmed digit per digit with [P]. A minus sign can only be adjusted on the
highest digit. After the last digit the display changes back into menu level.
Display, dISPL:
Default: actua
With this function the current measuring value, the min-value/max-value, the totaliser, the
process-controlled hold-value, the sliding average value, the constant value or the difference
between constant value and current value can be allocated to the display. With [P] the
selection is confirmed and the device changes into menu level.
Brightness control, Light:
Default: 15
The brightness of the display can be adjusted in 16 levels from 00 = very dark to 15 = very
bright via this parameter or alternatively via the navigation keys from the outside. During the
start of the device the level that is deposited under this parameter will always be used, even
though the brightness has been changed via the navigation keys in the meantime.
16
14
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
Menu level
Parameterisation level
Display flashing, FLASH:
Default: no
A display flashing can be added as additional alarm function either to single or to a combination
of off-limit condition. With no, no flashing is allocated.
Assignment (deposit) of key functions, tASt:
Default: no
For the operation mode, special functions can be deposited on the navigation keys [▲] [▼], in
particular this function is made for devices in housing size 48x24mm which do not have a 4th
key ([O]-key). If the min/max-memory was activated by EHtr, all measured min/max-values are
saved during operation and can be recalled via the navigation keys. The values get lost by
restart of the device. If the threshold value correction LI.12 or LI.34 was choosen, the values of the
threshold can be changed during operation without disturbing the operating procedure. With
tArA the device is set temporarily on a parametrised value. The device acknowledges the
correct taring with oo0oo in the display. Set.tA switches into the offset value and can be adjusted
via the navigation keys. Via totAL the current value of the totaliser can be displayed, after this
the device switches back on the parameterised display value. If tot.rE was deposited, the
totaliser can be set back by pressing of the navigation keys [▲] [▼], the device acknowledges
this with showing ooooo in the display. By allocation on EHt.rE the min/max-memory is deleted.
At ActuA the measuring value is shown, after this the device switches back on the
parameterised display value With light the brightness of the display is adjusted. This setting is
not saved and gets lost at a restart fo the device. Via selection L1.1, L1.1-2, li.1-3, l1.1-4, in case of 8
switching points li.1-5…li.1-8, threshold values can be addressed via the navigation keys; they
can be changed digit per digit or taken over by pushing the [P]-key. The adjustment is taken
over directly, an excisting limit value monitoring and the current measurement will not be
influenced by this. If no is selected, the navigation keys are without any function in the operation
mode.
15
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
17
5. Setting up the device
Menu level
Parameterisation level
Special function [O]-key, tASt.4:
Default: no
…
For the operation mode, special functions can be deposited on the [O]-key. This function is
activated by pressing the key. With tArA the device is set temporarily on zero and saved
permanently as offset. The device acknowledges the correct taring by showing ooooo in display.
Set.tA switches into the offset value and can be adjusted via the navigation keys. Via totAL the
current value of the totaliser can be displayed, after this the device switches back on the
parameterised display value. If tot.rE was deposited, the totaliser can be set back by pressing
of the navigation keys [▲] [▼], the device acknowledges this with ooooo in the display. EHt.rE
deletes the min/max-memory. If HOLD has been selected, the moment can be hold constant by
pressing the [O]-key and is updated by releasing the key. Advice: Hold is activated only, if HOLD
was selected under parameter DISPL. ActuA shows the measuring value, after this the device
switches back on the parameterised display value. The same goes for AvG, here the sliding
average value will be displayed. Via se.cal a sensor calibration is done by pressing the zero
key, the operating diagram is shown in chapter 8. The constant value const can be called up via
the key or adjusted digit per digit. At AL-1…AL-4 an output can be set and therewith can e.g. a
setpoint adjustment be done. If no is selected, the [O]-key is without any function in the
operation mode.
Special function digital input, dIG.In:
Default: no
…
For the operation mode, the above shown parameters can be laid on the optional digital input,
too. Functions description see tASt.4.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–fct–“.
16
18
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
5.4.3. Safety parameters
Menu group level
Menu level
Menu level
Parameterisation level
Adjustment of user code, U.Code :
Default: 0000
Via this code reduced sets of parameters out.le and al.lev can be unlocked during locked
programming. Further parameters are not available via this code. The U.CodE can only be
changed via the correct input of the A.CodE (Master code).
Master code, A.Code:
Default: 1234
By entering A.CodE the device will be released and all parameters unlocked.
Release/ lock analog output parameters, Out.LE:
Default: all
Analog output parameters can be locked or released for the user:
- En-oF: the initial or final value can be changed in operation mode
- Out.EO: the output signal can be changed from e.g. 0-20 mA to 4-20 mA or 0-10 VDC
- ALL: analog output parameters are released
- no: all analog output parameters are locked
Release/lock alarm parameters, AL.LEU:
Default: all
This parameter describes the user release/user lock of the alarm:
- LIMIt: here only the range of value of the threshold values 1-4 can be changed
- ALrM.L: here the range of value and the alarm trigger can be changed
- ALL: all alarm parameters are released
- no: all alarm parameters are locked
17
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
19
5. Setting up the device
Menu level
Parameterisation level
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–cod–“.
5.4.4. Serial parameters
Menu group level
Menu level
Menu level
Parameterisation level
Device address, ADDR:
Default: 001
The device address is adjusted from the smallest to the largest digit with the navigation keys
[▲] [▼] and confirmed digit per digit with [P]. A device address up to max. 250 is available.
Interface data: Baudrate 9600 bit/s, 8 databyte, 1 stopbit, no parity (8n1).
ModBus operating modes, b.mode:
Default: ascii
There are two different types of operating modes: ASCII and rtu. Modbus transfers no binary
cycle, but the ASCII-Code. Thus it is directly readable, however the data throughput is smaller
in comparison to the RTU. Modbus RTU (RTU = Remote Terminal Unit) transfers the data in
binary-coded. This leads to a good data troughput, even though the data cannot be evaluated
directly, as they first need to be transfered into a readable format.
Timeout, tIout:
Default: 000
The monitoring of the data transfer is parameterised in seconds up to max. 100 seconds; there
is no monitoring with an input of 000. The timeout is adjusted from the smallest to the largest
digit with the navigation keys [▲] [▼] and confirmed digit per digit with [P]. After the last digit
the device changes back into menu level.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–SER–“.
18
20
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
5.4.5. Analog output parameters for analog output 1
Menu group level
Menu level
Menu level
Parameterisation level
Selection reference of analog output, OutPt:
Default: actua
The analog output signal can refer to different functions, in detail these are the current
measurand, the min-value, the max-value, the totaliser function/sum function, the constant
value or the difference between current measurand and constant value. If HoLd was selected,
the signal of the analog output will be kept. It can be continued processing after a deactivation
of Hold. With [P] the selection is confirmed and the device changes into menu level.
Selection analog output, Out.rA:
Default: 4-20
Three output signals are available 0-10 VDC, 0-20 mA and 4-20 mA. Select the desired signal
with this function.
Setting the final value of the analog output, Out.En:
Default: 10000
The final value is adjusted from the smallest to the highest digit with [▲] [▼] and confirmed
digit per digit with [P]. A minus sign can only be parameterised on the highest digit. After the
last digit the device changes back into menu level.
Setting the initial value of the analog output, Out.OF:
Default: 00000
The initial value is adjusted from the smallest to the highest digit with [▲] [▼] and confirmed
digit per digit with [P]. A minus sign can only be parameterised on the highest digit. After the
last digit the device changes back into menu level.
19
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
21
5. Setting up the device
Menu level
Parameterisation level
Overflow behaviour, O.FLoU:
Default: edge
To recognise and evaluate faulty signals, e.g. by a controller, the overflow behaviour of the
analog output can be defined. As overflow can be seen either EdGE, that means the analog
output runs on the set limits e.g. 4 and 20 mA, or to.OFF (input value smaller than initial value,
analog output switches on e.g. 4 mA), to.End (higher than final value, analog output switches on
e.g. 20 mA). If to.MIn or to.MAX is set, the analog output switches on the smallest or highest
possible binary value. This means that values of e.g. 0 mA, 0 VDC or values higher than 20 mA
or 10 VDC can be reached. With [P] the selection is confirmed and the device changes into
menu level.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–out–“.
Analog output parameters for analog output 2
Menu group level
Menu level
Menu level
Parameterisation level
Selection reference of analog output, Ou2Pt:
Default: actua
The analog output signal can refer to different functions, in detail these are the current
measurand, the min-value, the max-value the totaliser function/sum function, the constant value
or the difference between current measurand and constant value. If HoLd is selected, the signal
of the analog output will be kept. It can be continued processing after a deactivation of Hold.
With [P] the selection is confirmed and the device changes into menu level.
20
22
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
Menu level
Parameterisation level
Selection analog output, Ou2.rA:
Default: 4-20
3 output signals are available 0-10 VDC, 0-20 mA and 4-20 mA. Select the desired signal with
this function.
Setting the final value of the analog output, Ou2.En:
Default: 10000
The final value is adjusted from the smallest to the highest digit with [▲] [▼] and confirmed
digit per digit with [P]. A minus sign can only be parameterised on the highest digit. After the
last digit the device changes back into menu level.
Setting the initial value of the analog output, Ou2.of:
Default: 00000
The initial value is adjusted from the smallest to the highest digit with [▲] [▼] and confirmed
digit per digit with [P]. A minus sign can only be parameterised on the highest digit. After the
last digit the device changes back into menu level.
Overflow behaviour, Ou2.fl:
Default: edge
To recognise and evaluate faulty signals, e.g. by a controller, the overflow behaviour of the
analog output can be defined. As overflow can be seen either EdGE, that means the analog
output runs on the set limits e.g. 4 and 20 mA, or to.OFF (input value smaller than initial value,
analog output switches on e.g. 4 mA), to.End (higher than final value, analog output switches on
e.g. 20 mA). If to.MIn or to.MAX is set, the analog output switches on the smallest or highest
possible binary value. This means that values of e.g. 0 mA, 0 VDC or values higher than 20 mA
or 10 VDC can be reached. With [P] the selection is confirmed and the device changes into
menu level.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–ou2–“.
21
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
23
5. Setting up the device
5.4.6. Relay functions
Menu group level
Menu level
Menu level
Parameterisation level
Alarm relay 1, rEL-1:
Default: al-1
The same applies for relays 2-4
….
….
Each setpoint (optional) can be linked up via 4 alarms (by default). This can either be inserted
at activated alarms AL1/4 or deactivated alarms ALN1/4. If LOGIC was selected, logical links are
available in the menu level LoG-1 and CoM-1. Access to these two menu levels is via LOGIC, at all
other selected functions, these two parameters are overleaped. Via On/OFF the setpoints can be
activated/deactivated, in this case the output and the setpoint display are set/not set on the
front of the device. The parameters Cal, Cal.of and CAL.en can only be used in accordance with
the semi-automatic calibration (Chapter 9. Sensor alignment). At Cal the relay switches during
sensor calibration, at cal.of during offset calibration and at Cal.en during the calibration of the
final value. With [P] the selection is confirmed and the device changes into menu level.
Logic relay 1, Log-1
Default: or
Here, the switching behaviour of the relay is defined via a logic link, the following schema
describes these functions with inclusion of AL-1 and AL-2. This parameter can only be selected if
LOGIC was selected under REl-1 .
A1 v A2
As soon as a selected alarm is activated, the relay
operates. Equates to operating current principle.
A1 v A2 = A1 Λ A2
The relay operates only, if no selected alarm is
active. Equates to quiescent current principle.
A1 Λ a2
The relay operates only, if all selected alarms are
active.
A1 Λ A2 = A1 v A2
As soon as a selected alarm is not activated, the
relay operates.
____ _ _
____ _ _
With [P] the selection is confirmed and the device changes into menu level.
24
22
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
Menu level
Parameterisation level
Alarms for relay 1, CoM-1:
Default: a.i
….
The allocation of the alarms to relay 1 happens via this parameter, one alarm or a group of
alarms can be chosen. With [P] the selection is confirmed and the device changes into menu
level.
Alarm relay 5, reL-5:
Default: al-5
The same applies for relays 6-8
….
….
Each setpoint (optional) can be linked up via 4 alarms (by default). This can either be inserted
at activated alarms AL6/8 or deactivated alarms ALN6/8. If LOGIC was selected, logical links are
available in the menu level LoG-1 and CoM-1. Access to these two menu levels is via LOGIC, at all
other selected functions, these two parameters are overleaped. Via On/OFF the setpoints can be
activated/deactivated, in this case the output and the setpoint display are set/not set on the
front of the device. The parameters Cal, Cal.of and CAL.en can only be used in accordance with
the semi-automatic calibration (Chapter 9. Sensor alignment). At Cal the relay switches during
sensor calibration, at cal.of during offset calibration and at Cal.en during the calibration of the
final value. With [P] the selection is confirmed and the device changes into menu level.
Logic relay 5, LoG-5:
Default: or
Here, the switching behaviour of the relay is defined via a logic link, the following schema
describes these functions with inclusion of AL-1 and AL-2:
A1 v A2
As soon as a selected alarm is activated, the relay
operates. Equates to operating current principle.
A1 v A2 = A1 Λ A2
The relay operates only, if no selected alarm is
active. Equates to quiescent current principle.
A1 Λ a2
The relay operates only, if all selected alarms are
active.
A1 Λ A2 = A1 v A2
As soon as a selected alarm is not activated, the
relay operates.
____ _ _
____ _ _
With [P] the selection is confirmed and the device changes into menu level.
23
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
25
5. Setting up the device
Menu level
Parameterisation level
Alarms for relay 5, CoM-5:
Default: a.5
….
The allocation of the alarms to relay 5 happens via this parameter, one alarm or a group of
alarms can be chosen. With [P] the selection is confirmed and the device changes into menu
level.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–rel–“.
5.4.7. Alarm parameters
Menu group level
Menu level
Menu level
Parameterisation level
Dependency alarm 1, ALrM.1:
Default: actua
The dependency of alarm.1 can be related to special functions, in detail these are the current
measuring value, the min-value, the max-value, the totaliser value/sum-value, the constant
value or the difference between the current measurand and the constant value. If Hold was
selected, the alarm is hold and processed just after deactivation of HOLD. EHtEr causes the
dependency either by pressing the [O]-key on the front of the housing or by an external signal
via the digital input. With [P] the selection is confirmed and the device changes into menu level.
Example:
By using the maximum value Alarm.1 = Max.va in combination with a threshold monitoring Fu-1 =
High, an alarm confirmation can be realised. Use the navigation keys, the 4th key or the digital
input for confirmation.
24
26
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
Menu level
Parameterisation level
Threshold values / limit values, LI-1:
Default: 2000
The limit value defines the threshold, that activates/deactivates an alarm.
Hysteresis for threshold values, HY-1:
Default: 00000
The delayed reaction of the alarm is the difference to the threshold value, which is defined by
the hysteresis.
Function for threshold value undercut / exceedance, Fu-1:
Default: high
A limit value undercut is selected with Louu (for LOW = lower limit value), a limit value
exceedance with High (for HIGH = higher limit value). If e.g. limit value 1 is on a threshold level
of 100 and allocated with function High, an alarm is activated by reaching of the threshold level.
If the threshold value was allocated to Low, an alarm will be activated by undercutting the
threshold value, as long as the hysteresis is zero.
Switching-on delay, ton-1:
Default: 000
For limit value 1 one can preset a delayed switching-on of 0-100 seconds.
Switching-off delay, toF-1:
Default: 000
For limit value 1 one can preset a delayed switching-off of 0-100 seconds.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–Al1–“.
The same applies for Al2 to al8.
25
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
27
5. Setting up the device
5.4.8. Totaliser (Volume metering)
Menu group level
Menu level
Menu level
Parameterisation level
State of totaliser, total:
Default: off
The totaliser realizes measurements on a time base of e.g. l/h, there the scaled input signal is
integrated by a time and steadily (select Stead) or temporarily (select temp) safed. Select the
constant storage for consumption measurements and the quick storage for frequently filling
processes. During the constant storage STEAD the current sum value is saved at each totaliser
reset. Furthermore it is saved every 30 minutes in the not-quick storage of the device. If Off is
selected, the function is deactivated. With [P] the selection is confirmed and the device
changes into menu level.
Time base, t.base:
Default: sec
Under this parameter the time base of the measurement can be preset in seconds, minutes or
hours.
Totaliser factor, Facto:
Default: ie0
…
At this the factor (1E0…1E6) respectively the divisor for the internal calculation of the
measuring value is assigned.
Setting up the decimal point for the totaliser, tot.dt:
Default: 0
The decimal point of the device can be adjusted with the navigation keys [▲] [▼]. With [P] the
selection is confirmed and the device changes into menu level.
28
26Eggenfelden l www.acs-controlsystem.de l [email protected]
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307
6. Reset to default values
Menu level
Parameterisation level
Totaliser reset, tot.re:
Default: ooooo
The reset value is adjusted from the smallest to the highest digit with the navigation keys
[▲] [▼] and digit per digit confirmed with [P]. After the last digit, the display switches back to
the menu level. The activator for the reset is parameter driven via the 4th key or via the optional
digital input.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–tot–“.
Programming interlock, run:
Menu group level
Description see page 9, menu level run
6. Reset to default values
To return the unit to a defined basic state, a reset can be carried out to the default values.
The following procedure should be used:
• Switch off the power supply
• Press button [P]
• Switch on voltage supply and press [P]-button until „- - - - -“ is shown in the display.
With reset, the default values of the program table are loaded and used for subsequent operation. This sets
the unit back to the state in which it was supplied.
Caution! All application-related data are lost.
27
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
29
7. Alarms / Relays
7. Alarms / Relays
This device has 8 virtual alarms that can monitor one limit value in regard of an undercut or exceedance.
Each alarm can be allocated to an optional relay output S1-S4; furthermore alarms can be controlled by
events like e.g. Hold or min/max-value.
Function principle of alarms / relays
Alarm / Relay x
Deactivated, instantaneous value, min/max-value, hold-value, totaliser
value, sliding average value, constant value, difference between
instantaneous value and constant value or an activation via the digital
input or the [O]-key
Switching threshold
Threshold / limit value of the change-over
Hysteresis
Broadness of the window between the switching thresholds
Working principle
Operating current / quiescent current
Operating current
By operating current the alarm S1-S4 is off
below the threshold and on on reaching the
threshold.
Quiescent current
By quiescent current the alarm S1-S4 is on
below the threshold and switched off on
reaching the threshold.
Switching-on delay
The switching-on delay is activated via an
alarm and e.g. switched 10 seconds after
reaching the switching threshold, a short-term
exceedance of the switching value does not
cause an alarm, respectively does not cause a
switching operation of the relay. The
switching-off delay operates in the same way,
keeps the alarm / the relay switched longer for
the parameterised time.
30
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
28
8. Interfaces
8. Interfaces
The interface RS485 is connected via a screened data line with twisted wires (Twisted-Pair). On each end
of the bus segment a termination of the bus lines needs to be connected. This is neccessary to ensure a
secure data transfer to the bus. For this a resistance (120 Ohm) is interposed between the lines Data B (+)
and Data A (–).
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
29
31
9. Sensor alignment offset / final value
9. Sensor alignment offset / final value
The device is equipped with a semi-automatic sensor calibration (sense). A switching output operates the
trimming resistor, which exists in some sensors. An adjustment of offset and final value takes place, after
which the sensor can be used directly. Depending on parameterisation, the calibration can be realized via
the fourth key or via the digital input. It is possible to key during the calibration steps. So, reference signals
can be connected manually. However the calibration will be interrupted after 30 seconds.
Press actuator for minimum 3
seconds.
Activate optional switching output.
For calibration
problems or 30
seconds holding
time.
For minimum 1 measuring cycle, minimum
1s or maximum per actuator.
Current measuring range value,
e.g. 0.061
For minimum 1 measuring cycle or
with actuator.
Switch-off/switch-on optional switching
output, e.g. 7,132
For minimum 1 measuring cycle, minimum
1s or maximum per actuator.
Current measuring range value.
For minimum 1 measuring cycle,
minimum 1s or maximum per actuator.
For calibration
problems or 30
seconds holding
time.
Optional: switch-off switching output and display
for minimum 1 measuring cycle or minimum 1s
holding time.
Back to regular operation mode, after
1s or 1 measuring cycle.
Back to regular operation mode.
32
30
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
10. Technical data
10. Technical data
Housing
Dimensions
96x48x120 mm (BxHxD)
96x48x139 mm (BxHxD) incl. plug-in terminal
Panel cut-out
92.0+0.8 x 45.0+0.6 mm
Wall thickness
up to 15 mm
Fixing
screw elements
Material
PC Polycarbonate, black, UL94V-0
Sealing material
EPDM, 65 Shore, black
Protection class
standard IP65 (front), IP00 (back side)
Weight
approx. 300 g
Connection
plug-in terminal; wire cross-section up to 2.5 mm2
Display
Digit height
14 mm
Segment colour
red (optional green, orange or blue)
Display range
-19999 up to 99999
Setpoints
one LED per setpoint
Overflow
horizontal bars at the top
Underflow
horizontal bars at the top
Display time
0.1 to 10.0 seconds
Input
Measuring range
Measuring error
Digit
> 1k Ω … < 1.000 kΩ
1… 100 %
0.5 % of measuring range
±1
Digital input
< 2.4 V OFF, 10 V ON, max. 30 VDC
RI ~ 5 kΩ
Accuracy
Temperature drift
100 ppm / K
Measuring time
0.1…10.0 seconds
Measuring principle
U/F-conversion
Resolution
approx. 18 bit at 1s measuring time
31
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
33
10. Technical data
Output
Analog output
0/4-20 mA / burden ≤500 Ω; 0-10 VDC / burden ≥10 kΩ, 16 bit
Switching outputs
Relay with change-over contacts
Switching cycles
250 VAC / 5 AAC; 30 VDC / 5 ADC
30 x 103 at 5 AAC, 5 ADC ohm resistive burden
10 x 106 mechanically
Diversification according to DIN EN50178 /
Characteristics according to DIN EN60255
PhotoMos-outputs
Closer contacts: 30 VDC/AC, 0.4 A
Interface
Protocol
Modbus with ASCII or RTU-protocol
RS232
9.600 Baud, no parity, 8 Databit, 1 Stopbit,
cable length max. 3 m
RS485
9.600 Baud, no parity, 8 Databit, 1 Stopbit,
cable length max. 1000 m
Power supply
100-240 VAC 50/60 Hz, DC ±10% (max. 15 VA)
10-40 VDC, 18-30 VAC 50/60 Hz (max. 15 VA)
Memory
EEPROM
Data life
≥ 100 years / 25°C
Ambient conditions
Working temperature
0…50°C
Storing temperature
-20…80°C
Wheatering resistance
relative humidity 0-80% on years average without dew
EMV
EN 61326, EN 55011
CE-sign
Conformity according to directive 2004/108/EG
Safety standard
According to low voltage directive 2006/95/EG
EN 61010; EN 60664-1
34
32
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
11. Safety advices
11. Safety advices
Please read the following safety advices and the assembly chapter 2 before installation and keep
it for future reference.
Proper use
The M3-15-device
DAL-311--device
is designed
for the
evaluation
display
of sensor
signals.
The
is designed
for the
evaluation
andand
display
of sensor
signals.
Attention! Careless use or improper operation can result in
personal injury and/or cause damage to the equipment.
Control of the device
The panel meters are checked before dispatch and sent out in perfect condition. Should there be
any visible damage, we recommend close examination of the packaging. Please inform the
supplier immediately of any damage.
Installation
DAL-311-device
must
installed
bysuitably
a suitably
qualified
specialist(e.g.
(e.g.with
witha a
qualification
The M3-15-device
must
be be
installed
by a
qualified
specialist
qualification
in in
industrial electronics).
Notes on installation
• There must be no magnetic or electric fields in the vicinity of the device, e.g. due to
transformers, mobile phones or electrostatic discharge.
• The fuse rating of the supply voltage should not exceed a value of 6A N.B. fuse.
• Do not install inductive consumers (relays, solenoid valves etc.) near the device and
suppress any interference with the aid of RC spark extinguishing combinations or free-wheeling
diodes.
• Keep input, output and supply lines separate from one another and do not lay them parallel with
each other. Position “go” and “return lines” next to one another. Where possible use twisted pair.
So, you receive best measuring results.
• Screen off and twist sensor lines. Do not lay current-carrying lines in the vicinity. Connect the
screening on one side on a suitable potential equaliser (normally signal ground).
• The device is not suitable for installation in areas where there is a risk of explosion.
• Any electrical connection deviating from the connection diagram can endanger human life
and/or can destroy the equipment.
• The terminal area of the devices is part of the service. Here electrostatic discharge needs to be
avoided. Attention! High voltages can cause dangerous body currents.
• Galvanic isolated potentials within one complex need to be placed on an appropriate point
(normally earth or machines ground). So, a lower disturbance sensibility against impacted
energy can be reached and dangerous potentials, that can occur on long lines or due to faulty
wiring, can be avoided.
33
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
35
12. Error elimination
12. Error elimination
Error description
Measures
1.
The unit permanently indicates
overflow.
• The input has a very high measurement, check
the measuring circuit.
• With a selected input with a low voltage signal,
it is only connected on one side or the input is
open.
• Not all of the activated setpoints are
parameterised. Check if the relevant
parameters are adjusted correctly.
2.
The unit permanently shows
underflow.
• The input has a very low measurement, check
the measuring circuit.
• With a selected input with a low voltage signal,
it is only connected on one side or the input is
open.
• Not all of the activated setpoints are
parameterised. Check if the relevant
parameters are adjusted correctly.
3.
The word HELP lights up in the
7-segment display.
• The unit has found an error in the configuration
memory. Perform a reset on the default values
and reconfigure the unit according to your
application.
4.
Program numbers for parameterising
of the input are not accessible.
• Programming lock is activated.
• Enter correct code.
5.
Err1 lights up in the 7-segment display.
• Please contact the manufacturer if errors of
this kind occur.
6.
The device does not react as
expected.
• If you are not sure that the device has been
parameterised before, then follow the steps as
written in chapter 6 and set it back to its
delivery status.
M3_15GB.pdf
36
34
update: 21.04.2015
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
37

Pegel
Druck


Temperatur Durchfluss
Registrierung
Visualisierung
¸



Füllstand



Messumformer
Sensorik
USV
Wir erwarten Ihren Anruf.
ACS-CONTROL-SYSTEM GmbH
Lauterbachstr. 57
D- 84307 Eggenfelden
know how mit System
Ihr Partner für Messtechnik und Automation
¸
[email protected]
www.acs-controlsystem.de
Stand 04/2015
ACS-CONTROL-SYSTEM
Tel: +49 (0) 8721-9668-0
Fax: +49 (0) 8721-9668-30
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement