Operating Instructions - ACS-CONTROL
User Manual M1
Operating Instructions
Direct voltage signals (via Shunt) 0-60-150 mV
DAK-101x300S
User
Manual M1
Direct voltage signals (via Shunt) 0-60-150 mV
Direct voltage signals (via Shunt) 0-60-150 mV
Technical features:
• red display of -1999…9999 digits (optional: green, orange or blue display)
• minimal installation depth: 27 mm without plug-in terminal
• adjustment via factory default or directly on the sensor signal
•Technical
min/max-memory
features:
• 10 adjustable supporting points
•• display
flashing
at threshold digits
exceedance
/ undershooting
red display
of -1999…9999
(optional:
green, orange or blue display)
•• tara
function
minimal installation depth: 27 mm without plug-in terminal
•• programming
via access
code on the sensor signal
adjustment viainterlock
factory default
or directly
•• protection
class IP65 at the front
min/max-memory
•• plug-in
terminalsupporting points
10 adjustable
•• pc-based
configuration
software
PM-TOOL
with CD and USB-adapter for devices without keypad
display flashing
at threshold
exceedance
/ undershooting
for a simple adjustment of standard devices
• tara function
• programming interlock via access code
• protection class IP65 at the front
• plug-in terminal
• pc-based configuration software PM-TOOL with CD and USB-adapter for devices without keypad
for a simple adjustment of standard devices
Order code
2
6
power supply
24V DC galvanic seperated
4-20mA 2-wire, current loop display
function input
3 Shunt 60 / 150 mV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
function output
0 display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DAK-101
2
0
9
standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
dimension strips and configuration as specified . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S
0
standard, protection IP65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
Content
1.
Brief description
2
2.
Assembly
2
3.
Electrical connection and conenction examples
3
4.
Function description and operation
4
4.1. Programming software PM-TOOL
4
Setting up the device
5
5.1. Switching on
5
5.2. Standard parameterisation (flat operation level)
5
5.
Value assignment for control of the signal input
5.3. Programming interlock RUN
6
Activation/Deactivation of the programming interlock or
change into extended parameterisation
5.4. Extended parameterisation
6
Superior device functions like e.g.:
6.
- rescaling of the input signals, EndA, OFFA
6
- parameterisation of a TARA-function, TARA
6
- zero point slowdown of the input signal, Zero
7
- allocation of functions onto the navigation keys
7
- adjustment of limit values for optical alarm, LI-1/2
7
- safety parameter for locking of the programming, Code
9
- input of supporting points for the linearisation of the input signals, spct
9
Reset to default values
9
Reset of the parameter onto delivery condition
7.
Alarms / Switching points
10
Functional principle of the optical switching points
8.
Technical data
11
9.
Safety advice
13
10.
Error elimination
14
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
1
3
1. Brief description
2. Assembly
1. Kurzbeschreibung
The panel instrument M1-72 is a 4-digit device for direct voltage signals (via Shunt) and a visual limit value
monitoring via the display. The configuration happens via three front keys or via the optional PC-software
The panel instrument DAK-101 is a 4-digit device for direct voltage signals (via shunt) and direct current signals and a visual
PM-TOOL.
An integrated programming interlock prevents unrequested changes of the parameter and can be
limit value monitoringvia the display. The configuration happens via three front keys or via the optional PC-software PM-TOOL.
unlocked
again
an individual
code.
An integratedvia
programming
interlock
prevents unrequested changes of the parameter and can be unlocked again via an individual code. The
electrical connection
happens
on the
rearside
via plug-interminals.
The electrical
connection
happens on
the rear
side
via plug-in
terminals.
Selectable
functionslike
like e.g.
of the
zeropoint
change ofathe
limit value
in operaSelectable
functions
e.g.the
therecall
recall
of min/max-value,a
the min/max-value,
a slowdown,a
zero pointdirect
slowdown,
direct
change
of the
ting mode an dadditional measuring supporting points for linearisation complete the modern device concept .
limit value in operating mode and additional measuring supporting points for linearisation complete the
modern device concept.
2. Assembly
Please read the Safety instructions on page 13 before installation and keep this user manual for future reference.
3,0
24,0
Se
alin
g
48
,0
1.
2.
3.
°C
l.
inc
h
0
t
,
54 dep inal
n
m
atio in ter
l
l
a
t
Ins plug
After removing the fixing elements, insert the device.
Check the seal to make sure it fits securely.
Click the fixing elements back into place and tighten the clamping screws by hand. Then use a
screwdriver to tighten them another half a turn.
CAUTION! The torque should not exceed 0.1 Nm!
4
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
3. Electrical connection
3. Electrical connection
Type
TypeDAK-101x300S
M1-7VR4A.0002.770CD – supply 24 VDC
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5
4. Function description and operation
4. Function description and operation
Operation
The operation is divided into two different levels.
Menu Level
Here it is possible to navigate between the individual menu items.
Parameterization level:
The parameters stored in the menu item can be parameterized here.
Functions that can be adjusted or changed are always indicated with a flashing of the display. Adjustments
made at the parameterization level should be always confirmed by pressing the [P] key to save them.
However, the display automatically saves all adjustments and then switches to operation mode if no further
keys are pressed within 10 seconds.
Level
Button
Description
Change to parameterization level with the relevant parameters
Menu level
For navigation at the menu level
To confirm the changes made at the parameterization level
Parameterization
level
To change the value or setting
Example:
Menu level
Parameterization level
4.1. Programming via configuration software PM-TOOL-MUSB12:
You receive the software on CD incl. an USB-cable with a device adapter. The connection is done via a 12pole micromatch connector plug on the back and the PC is connected via an USB connector plug.
System requirements:
PC with USB interface
Software:
Windows XP, Windows Vista
With this tool the device configuration can be created, skipped and safed on the PC. Via the easy to handle
program surface the parameter can be changed, whereat the mode of operation and the possible selection
options can be preset via the program.
CAUTION!
During parameterisation with connected measuring signal, make sure that the measuring signal has no mass
supply to the programming plug. The programming adapter is galvanic not isolated and directly connected
with the PC. Via polarity of the input signal, a current can discharge via the adapter and destroy the device as
well as other connected components!
4
6
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
5. Setting up the device
5. Setting up the device
5.1. Switching on
Once the installation is complete, you can start the device by applying the current loop. Check beforehand
once again that all the electrical connections are correct.
Starting sequence
For 1 second during the switching-on process, the segment test (8 8 8 8 8) is displayed, followed by an
indication of the software type and, after that, also for 1 second, the software version. After the start-up
sequence, the device switches to operation/display mode.
5.2. Standard parameterization:
To be able to parameterize the display, press the [P] key in operating mode for 1 second. The display then
changes to the menu level with the first menu item TYPE.
Menu level
Parameterization level
Selection of the input signal, TYPE:
Default: sens
There are several measuring inputs options: 0-60 mV or 0-150 mV signals as the works
calibration (without application of the sensor signal) and Sens as the sensor calibration (with the
sensor applied). Confirm the selection with [P] and the display switches back to menu level.
Setting the measuring range end value, END:
Default: 1000
Set the end value from the smallest to the highest digit with [▲] [▼] and confirm each digit with
[P]. A minus sign can only be parameterized on the highest value digit. After the last digit, the
display switches back to the menu level. If Sens was selected as the input option, you can only
select between noca and cal. With noca, only the previously set display value is taken over, and
with cal, the device takes over both the display value and the analogue input value.
Setting the measuring range start/offset value, offs:
Default: 0000
Enter the start/offset value from the smallest to the highest digit [▲] [▼] and confirm each digit
with [P]. After the last digit the display switches back to the menu level. If Sens was selected as
the input option, you can only select between noca and cal. With noca, only the previously set
display value is taken over, and with cal, the device takes over both the display value and the
analogue input value.
Setting the decimal point, dot:
Default: 0
The decimal point on the display can be moved with [▲] [▼] and confirmed with [P]. The
display then switches back to the menu level again.
5
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
7
5. Setting up the device
Menu level
Parameterization level
Setting the display time, SEC:
Default: 01.0
then
The display time is set with [▲] [▼]. The display moves up in increments of 0.1 up to 1 second
and in increments of 1.0 to 10.0 seconds. Confirm the selection by pressing the [P] button. The
display then switches back to the menu level again.
5.3. Programming interlock RUN
Activation / deactivation of the programming lock and completion of the standard
parameterization, run:
Default: uloc
With the aid of the [▲] [▼] keys, you can choose between the deactivated key lock Uloc (works
setting) and the activated key lock Loc. Make the selection with [P]. After this, the display
confirms the settings with "- - - -", and automatically switches to operating mode. If Loc was
selected, the keyboard is locked. To get back into the menu level, you must press [P] for 3
seconds in operating mode. You must now enter the CODE (works setting 1 2 3 4) that appears
using the [▲] [▼] keys plus [P] to unlock the keyboard. FAIL appears if the input is wrong.
5.3. Extended parameterization
By pressing the [▲] & [▼] buttons during standard parameterization for one second, the display switches to
the extended parameterization mode. Operation is the same as in standard parameterization.
Menu level
Parameterization level
Rescaling the measuring input values, EndA :
With the aid of this function, you can rescale the input value of e.g. 50 mV (works setting)
without applying a measuring signal. If sensor calibration has been selected, these parameters
are not available.
Rescaling the measuring input values, OFFA:
With the aid of this function, you can rescale the input value of e.g. 0,5 mV (works setting)
without applying a measuring signal. If sensor calibration has been selected, these parameters
are not available.
8
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
6
5. Setting up the device
Menu level
Parameterization level
Setting the tare/offset value, tArA:
Default: 0
The given value is added to the linerarized value. In this way, the characteristic line can be
shifted by the selected amount.
Zero point slowdown, ZErO:
Default: 0
With zero point slowdown, a value range around zero can be preselected at which the display
shows zero. If, for example, a 10 is set, the display would show a zero in the range from -10 to
+10 and continue below it with -11 and above it with +11.
Min/max-value inquiry - Assignment of key functions, Tast:
Default: no
Here, you can enter for the operating mode either a min/max-value inquiry or a threshold value
correction on the arrow keys.
If the min/max-memory is activated with EHER, the measured min/max-values will be saved
during operation and can be called up via the arrow keys [▲] [▼]. The values are lost if the
device is restarted.
If the threshold value correction LI.1 is selected, the limit values can be changed during
operation without hindering the operating procedure.
With tara the display is tared to zero and is saved permanently as offset. The device confirms
the correct taring by showing 0000 in the display. If No is parameterized, the navigation keys
[▼] [▲] have no function in operating mode.
Flashing of display, FLAS:
Default: no
Here, flashing of the display can be added as an extra alarm function, either to the first limit
value (select: LI-1), the second limit value (select: LI-2) or to both limit values (select: LI-12). With
No (works setting), no flashing is assigned at all.
Limit values / Limits, LI-1:
Default: 0200
For both limit values, two different values can be parameterized. With this, the parameters for
each limit value are called up one after the other.
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
7
9
5. Setting up the device
Menu level
Parameterization level
Hysteresis for limit values, HY-1:
Default: 0000
For both limit values, a hysteresis function exists that reacts according to the functional
principle (operating current / quiescent current).
Function if display falls below / exceeds limit value, FU-1:
Default: hi9h
To indicate if the value falls below the lower limit value, Louu can be selected (LOW = lower
limit value) and if it goes above the upper limit value, high can be selected (HIGH = upper limit
value). LOW corresponds to the quiescent current principle and HIGH to the operating current
principle.
Limit value / Limits, LI-2:
Default: 0300
For both limit values, two different values can be parameterized. With this, the parameters for
each limit value are called up one after the other.
Hysteresis for limit values, HY-2:
Default: 0000
For both limit values, a hysteresis function exists that reacts according to the functional
principle (operating current / quiescent current).
Function if display falls below / exceeds limit value, FU-2:
Default: hi9h
To indicate if the value falls below the lower limit value, Louu can be selected (LOW = lower
limit value) and if it goes above the upper limit value, high can be selected (HIGH = upper limit
value). LOW corresponds to the quiescent current principle and HIGH to the operating current
principle.
10
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
8
6. Reset to default values
Menu level
Parameterization level
Setting the code, CODE:
Default: 1234
With this setting, it is possible to select an individual code (works setting 1 2 3 4) for locking the
keyboard. To lock/release the key, proceed according to menu item run.
Supporting points - Number of additional supporting points, SPCt:
Default: 0
In addition to the start and end value, 8 extra supporting points can be defined to linearise nonlinear sensor values. Only the activated set point parameters are displayed.
Display values for supporting points, dIS1 … dIS5:
Under this parameter the supporting points are defined on a value basis. At the sensor
calibration one will be asked at the end (like at Final value/Offset, too), if a calibration shall be
triggered.
Analogue values for supporting points, INP1 … INP8:
Supporting points are always preset according to the selected input signal mV. Here the
desired analog values can be freely adjusted in ascending order.
6. Reset to default values
To return the unit to a defined basic state, a reset can be carried out to the default values.
The following procedure should be used:
• Switch off the power supply
• Press button [P]
• Switch on voltage supply and press [P]-button until „- - - -“ is shown in the display.
With reset, the default values of the program table are loaded and used for subsequent operation. This puts
the unit back to the state in which it was supplied.
Caution! All application-related data are lost.
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
9
11
7. Alarms and switching points
7. Alarms and switching points
Functional principle of the switching points
Limit value exceedance “High”
The setpoint S1-S2 is “off” below the
threshold and “on” on reaching the
threshold.
Limit value undercut “low”
The setpoint S1-S2 is “on” below
the threshold and switched “off”
on reaching the threshold.
Alarms / optical setpoint display
An activated setpoint can be optically indicated by flashing of the 7-segment display.
Functional principle of the alarms
12
Alarm
Deactivated, display value
Threshold
Threshold/limit value for switch over
Hysteresis
Width of the window between the thresholds
Operating principle
Limit value exceedance / limit value undercut
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
10
8. Technical data
8. Technical data
Housing
Dimensions
48x24
48x24x27 mm (BxHxT)
48x24x54 mm (BxHxT) including plug-in terminal
Panel cut-out
48x24
45.0+0.6 x 22.2+0.3 mm
Insulation thickness
up to 3 mm
Fixing
snap-in screw element
Material
PC Polycarbonate, black, UL94V-0
Sealing material
EPDM, 65 Shore, black
Protection class
standard IP65 (front), IP00 (back side)
Weight
approx. 100 g
Connection
plug-in terminal; wire cross section up to 2.5 mm 2
Display
Digit height
10 mm
Segment colour
red
Display range
-1999 to 9999
Setpoints
optical display flashing
Overflow
horizontal bars at the top
Underflow
horizontal bars at the bottom
Display time
0.1 to 10.0 seconds
Input
Measuring range
Ri
Measuring fault
Digit
min. -5…max. 80 mV
0-60 mV
12 kΩ
0.5 % of measuring range
±1
min. -10…max. 180 mV
0-150 mV
30 kΩ
0.5 % of measuring range
±1
Temperature drift
100 ppm / K
Measuring time
0.1…10.0 seconds
Measuring principle
U/F-conversion
Resolution
approx. 18 bit at 1s measuring time
Power pack
24 VDC ± 10 % max. 1 VA
Memory
EEPROM
Data life
≥ 100 years at 25°C
11
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
13
8. Technical data
Ambient conditions
Working temperature
0°C…60°C
Storing temperature
-20°C…80°C
Weathering resistance
relative humidity 0-80% on years average without dew
EMV
EN 61326
CE-sign
Conformity to directive 2004/108/EG
Safety standard
According to low voltage directive 2006/95/EG
EN 61010; EN 60664-1
14
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
12
9. Safety advices
9. Safety advice
Please read the following safety advice and the assembly chapter 2 before installation and keep it
for future reference.
Proper use
The M1-72-device
DAK-101--device
is designed
evaluation
display
of sensor
signals.
The
is designed
for for
thethe
evaluation
andand
display
of sensor
signals.
Danger!
Careless use or improper operation can result in
personal injury and/or damage to the equipment.
Control of the device
The panel meters are checked before dispatch and sent out in perfect condition. Should there be
any visible damage, we recommend close examination of the packaging. Please inform the
supplier immediately of any damage.
Installation
The
must
be be
installed
by by
a suitably
qualified
The M1-72-device
DAK-101-device
must
installed
a suitably
qualifiedspecialist
specialist (e.g.
(e.g. with
with aa qualification
qualification in
in
industrial
electronics).
industrial electronics).
Notes on installation
• There must be no magnetic or electric fields in the vicinity of the device, e.g. due to transformers,
mobile phones or electrostatic discharge.
• The fuse rating of the supply voltage should not exceed a value of 6A N.B. fuse.
• Do not install inductive consumers (relays, solenoid valves etc.) near the device and suppress
any interference with the aid of RC spark extinguishing combinations or free-wheeling diodes.
• Keep input, output and supply lines separate from each other and do not lay them parallel with
each other. Position “go” and “return lines” next to one another. Where possible use twisted pair.
So, the best measuring results can be received.
• Screen off and twist sensor lines. Do not lay current-carrying lines in the vicinity. Connect the
screening on one side on a suitable potential equaliser (normally signal ground).
• The device is not suitable for installation in areas where there is a risk of explosion.
• Any electrical connection deviating from the connection diagram can endanger human life and/or
can destroy the equipment.
• The terminal area of the devices is part of the service. Here electrostatic discharge needs to be
avoided. Attention! High voltages can cause dangerous body currents.
• Galvanic isolated potentials within one complex need to be placed on an appropriate point
(normally earth or machines ground). So, a lower disturbance sensibility against impacted energy
can be reached and dangerous potentials, that can occur on long lines or due to faulty wiring, can
be avoided.
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
13
15
10. Error elimination
10. Error elimination
Error description
Measures
1.
The unit permanently indicates
overflow.
• The input has a very high measurement, check
the measuring circuit.
• With a selected input with a low voltage signal, it
is only connected on one side or the input is
open.
• Not all of the activated setpoints are
parameterised. Check if the relevant parameters
are adjusted correctly.
2.
The unit permanently shows
underflow.
• The input has a very low measurement, check
the measuring circuit .
• With a selected input with a low voltage signal, it
is only connected on one side or the input is
open.
• Not all of the activated setpoints are
parameterised. Check if the relevant parameters
are adjusted correctly.
3.
The word "HELP " lights up in the
7-segment display.
• The unit has found an error in the configuration
memory. Perform a reset to the default values
and re-configure the unit according to your
application.
4.
Program numbers for parameterising
of the input are not accessible.
• Programming lock is activated
• Enter correct code
5.
"Err1" lights up in the 7-segment
display
• Please contact the manufacturer if errors of this
kind occur.
6.
The device does not react as
expected.
• If you are not sure if the device has been
parameterised before, then follow the steps as
written in chapter 6 and set it back to its delivery
status.
M1_72GB.pdf
16
14
update: 16.09.2014
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
ACS-CONTROL-SYSTEM GmbH l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
17

Pegel
Druck


Temperatur Durchfluss
Registrierung
Visualisierung
¸



Füllstand



Messumformer
Sensorik
USV
Wir erwarten Ihren Anruf.
ACS-CONTROL-SYSTEM GmbH
Lauterbachstr. 57
D- 84307 Eggenfelden
know how mit System
Ihr Partner für Messtechnik und Automation
¸
[email protected]
www.acs-controlsystem.de
Stand 07/2014
ACS-CONTROL-SYSTEM
Tel: +49 (0) 8721-9668-0
Fax: +49 (0) 8721-9668-30
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement