DNR / DWDR / IR Varifocal Vandal Dome

EV-2806-NMMQ (NTSC)
EV-2806-PMMQ (PAL)
DNR / DWDR / IR
Varifocal Vandal Dome Cameras
Installation Manual
3 Cameras in 1:
1 /3 ”
Sony Super HAD II CCD
2.8~12mm Varifocal lens
Digital Slow Shutter (DSS)
OSD with service monitor port
600 TV lines
Weatherproof (IP65)
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
ENFORCER DNR / DWDR / IR Varifocal Vandal Dome Cameras
Specifications:
Video output mode
Type
CCD
Resolution
Lens
# of IR LEDs
Pickup elements
Sync
Video output
Minimum illumination
S/N ratio
On screen display (OSD)
Motion detection
Backlight compensation
White balance
Electronic shutter
Auto gain
3D-DNR
Day & night (color)
Sharpness
Privacy
Operating voltage
Current draw
IP Rating
Operating temperature
Dimensions
Weight
EV-2806-NMMQ
NTSC
EV-2806-PMMQ
PAL
IR LED Dome Camera
Sony Super HAD II
600 TV Lines
2.8~12mm Varifocal
33
1/3”
768x494 pixels
752x582 pixels
Internal
1Vp-p composite video, 75Ω
0.000006-lux (LEDs ON)
>52dB (AGC OFF)
Built-in and controlled by internal joystick
4 zones
HLC/BLC/Off
ATW / AWC / MANUAL (1800°~10,500° K)
Auto/Manual (adjustable range: 1/60~1/120,000 sec)
Selectable: Low, Middle, High, Off
On/Off (adjustable range: 0~100)
Selectable: Color, Auto, B/W
On/Off (adjustable range: 0~31)
On/Off (8 programmable zones)
12VDC/24VAC ±10%
[email protected] (LEDs OFF), [email protected] (LEDs ON)
IP65
-4°~122° F (-20°~50° C)
51/2”x315/16” (140x100 mm)
32-oz (900g)
Parts List:
1 x Manual
1 x Camera
1 x Hex wrench
3 x Hex screws
1 x White rubber sleeve
1 x Black rubber sleeve
Dimensions:
1 x DC plug with
terminal block
Using the OSD:
OSD Joystick
51/2”(140mm)
315/16”
(100mm)
2
1 x Service monitor
port connector
Use the OSD joystick located on the
camera’s PC board to control the OSD
and configure the camera’s settings. See
the OSD manual for more details.
SECO-LARM U.S.A., Inc.
ENFORCER DNR / DWDR / IR Varifocal Vandal Dome Cameras
Overview:
Service monitor
port
OSD joystick
Mounting
screw
Wiring
notch
Zoom
Focus
Tilt
adjustment
knob
Set screw
Dome
Dome ring
Rubber
sleeve
(optional)
Female BNC
connector
Important:
Do not cut the DC jack or the
female BNC connector as this will
void the warranty.
DC Plug to
terminal block
DC Jack
Before Starting:
1. Please read this manual carefully and keep it for future
reference.
2. Use the camera within given temperature and electrical
limits.
3. Do not aim the LEDs directly at the eyes when the LEDs
are on.
4. Do not point the camera at the sun. Heat could damage
the camera, even when not in use.
5. Do not mount the camera in areas exposed to radiation,
strong magnetic fields, or strong electrical signals*.
6. Do not open or disassemble the camera. There are no
field-serviceable parts inside.
7. Do not drop the camera or subject it to strong
vibrations.
*Note: Many video monitors produce strong
electromagnetic fields close to the display CRT,
especially when the monitor is turned on or during
de-Gaussing, which occurs automatically with many
monitors when turning on.
Installation:
1. Run hidden cables from the video source and power
supply and connect to the camera. Do not cut the DC
jack or female BNC connector as this will void the
warranty. If needed, use the included SECO-LARM
DC plug with terminal block.
2. Test the voltage from the power supply.
Use 12VDC or 24VAC.
3. Undo the set screws on the side of the dome ring using
the included allen wrench and remove the dome from
the base.
4. Hold the camera against the wall, ceiling, or other
mounting surface while watching the monitor to find the
best mounting location. Mark that location
with a pencil.
Mount the base to the wall or ceiling using the four
included mounting screws. If the wall is made of brick,
drywall, or similar material, it may be necessary to use
screw anchors (not included).
SECO-LARM U.S.A., Inc.
5. If surface wiring, use the wiring notch in the base.
6. Adjust the camera angle as needed. Use the
OSD control joystick to adjust the camera settings
(See the OSD manual). Connect a service
monitor to the service monitor port connector for
on-site adjustments.
7. Test the video signal.
8. To adjust zoom and focus, loosen the lock knobs
by hand or with a screwdriver. Slide left or right to
adjust. Do not use power tools. Lens damage
may result
9. Reattach the dome to the camera.
10. Use the included allen wrench to tighten the set
screw, securing the dome to the base.
11. If needed, fit one of the included rubber sleeves
over the dome so that it covers the dome ring
and base.
12. Do a final test of the video camera and monitor.
3
ENFORCER DNR / DWDR / IR Varifocal Vandal Dome Cameras
Troubleshooting:
The screen is blank.
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the
monitor is connected properly.
The screen image is dim
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
The screen image has poor contrast.
Adjust the monitor’s contrast knob.
Change the position of the camera.
The screen image flickers.
Change the position of the camera.
The screen image is distorted.
Change the position of the camera.
The camera case is hot.
Check that the correct power supply is in use.
IR LEDs do not turn on.
Check that the correct power supply is in use.
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open
the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a
period of three (3) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of
any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is
not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999
4
Website: www.seco-larm.com
E-mail: [email protected]
PIKHR1
MiEV-2806-xMMQ_1106.docx
SECO-LARM U.S.A., Inc.