STD32 User Manual
STD32
User Manual
Revision 1.2
Important information
This technical description contains important information for start up and use of the STD32.
Read it carefully before you start working with the STD32.
The warranty will be void should damage occur due to non-compliance with these instructions
for use. We cannot accept any responsibility for consequential loss.
We cannot be held responsible for material loss or personal injury that is due to incompetent
use or non-compliance with the safety instructions. The warranty will be void in such
circumstances.
The STD35 contains highly integrated components which can be damaged by electrostatic
discharge if the user would open the housing.
CEP preserves the right to change the included information without notice and doesn’t take
responsibility for errors in the document and/or missing information.
Therefore only touch the STD32 on the housing or connectors and avoid touching
the components on the board.
Safety Instructions
When using products which are exposed to electric voltage the valid VDE-regulations
have to be observed. Especially VDE 0100, VDE 0550/0551, VDE 0700, VDE 0711
and VDE 0860 are applicable.







All wiring work has to be done in a voltage free state only
All cables and wires which are energized and connected to the device, the module, or
components have to be checked regularly for any damage to the isolation shielding or
fractures in the cables. If the supply cables are visibly damaged the device has to be taken
out of operation immediately until the faulty cable has been exchanged
Before putting a device into operation, it has to be clarified, whether this device or module
is appropriate for the field of application. In case of doubt ask a specialists or the
manufacturer of the device.
Please note that we are not responsible for any errors in usage or connection. Therefore we
cannot accept any responsibility for consequential loss.
Before opening the device always disconnect the mains adapter or make sure that the
device is disconnected from the power supply.
Components, modules or devices have to be built into a housing before they are put into
operation. During installation they should not be connected to any power supply .
You should only use tools on components, modules, or devices if they are disconnected
from the power supply, and residual electric charge (which may still be stored in some
components inside the device) has been discharged.
2





When using components or modules it is necessary to strictly observe the specification
given in the corresponding description of these components.
If a description for a private end-customer does not clearly state which electric data is valid
for a component or a module, how to wire the device, which external components, or
additional devices can be connected or which parameters these components are allowed to
have, a specialist must be contacted.
Devices which operate with greater than 35 Volts have to be connected by a specialist.
Before putting the device into operation it should be checked that there is no current
leakage on the housing.
In case that measurements with the opened housing are necessary, an isolatingtransformer has to be integrated for safety reasons. Alternatively the voltage can be
supplied by an appropriate power supply which complies with the safety regulations. All
wiring work has to be done in a voltage free state only.
Table of Contents
Important information ......................................................................................................................... 2
Safety Instructions .............................................................................................................................. 2
1
Introduction................................................................................................................................. 5
2
Background Information ............................................................................................................... 6
2.1
GSM-Network in general......................................................................................................... 6
2.2
GPRS .................................................................................................................................... 6
2.3
Quadband Frequencies........................................................................................................... 6
2.4
E-Mail via SMTP ..................................................................................................................... 6
3
Operating Conditions .................................................................................................................... 7
4
Proper Use .................................................................................................................................. 7
5
Introduction................................................................................................................................. 8
6
Quick start up ............................................................................................................................ 10
6.1
General preparations............................................................................................................ 10
6.2
Hardware preparations ......................................................................................................... 10
6.3
Configuration Call ................................................................................................................ 11
6.4
Quick configuration check..................................................................................................... 11
7
Basic SMS Commands................................................................................................................. 12
7.1
Table of Basic Commands .................................................................................................... 12
7.2
Send SMS Commands .......................................................................................................... 13
7.3
Explanation of the commands ............................................................................................... 13
7.4
Examples for SMS Commands ............................................................................................... 15
8
E-Mail functionality via GPRS ....................................................................................................... 16
8.1
Configuration of the E-Mail functionality ................................................................................ 16
8.2
Additional E-Mail configuration possibilities ............................................................................ 18
9
Complete list of commands ......................................................................................................... 21
10
Connecting the camera............................................................................................................ 25
11
Configuration Tool .................................................................................................................. 27
12
Troubleshooting ...................................................................................................................... 28
13
Accessories ............................................................................................................................ 29
14
Technical data ........................................................................................................................ 30
15
Document history.................................................................................................................... 31
4
1
Introduction
Thank you very much for purchasing our CEP STD32 telemetry device!
The STD32 offers the user the possibility to remotely switch ON or OFF electronic devices and
to receive alarm messages via (SMS). You can switch devices either with an SMS or using a
simple voice call. Alarm messages (SMS) can be received with any mobile phone supporting
SMS functionality.
With the new generation of the STD32 you now also have the possibility to receive alarm
messages via e-mail.
With the help of the digital camera which is available as an accessory, pictures can be taken
and sent via e-mail triggered by an alarm.
We wish you success and joy in using your new STD32!
Concerning the user manual
This document is meant to help you use the various functions of the device in the most optimal
way. Therefore we ask you to please read this manual carefully.
If you are in a hurry and want to make yourself familiar with the details of the product later,
then please read chapter 6 “Quick Start-up” first.
There you will find all necessary information to put the device into operation.
The information in this document has been gathered after thorough inspection but they are not
be taken as assurance of end product properties.
The written approval of CEP AG is mandatory before you can pass on or reproduce this
documentation for this product or the software or use the content.
CEP reserves the right to change the data mentioned here without prior notice and does not
take any responsibility for technical inaccuracies and/or omissions. This manual has been
thoroughly checked; should you nevertheless find an error or want to express criticism or make
suggestions, please send an e-mail to
E-Mail: [email protected]
Oberhaching, 21st Feb 2014
© 2014 CEP AG, Oberhaching, Germany
2
Background Information
2.1 GSM-Network in general
The GSM Network (Global System for Mobile Communications) is a standard for all-digital
mobile phone networks. GSM has been created to provide a mobile telephone system offering
the users Europe wide mobility and voice services compatible with ISDN or analog services.
Originally GSM has been designed for voice calls, the transmission of text messages (SMS) and
the transmission of data with a constant data speed. With the success of the internet an
evolution of GSM started. The GSM network was expanded to offer packet oriented data
transmission (e.g. via GPRS) while keeping all other features and being fully downwards
compatible.
2.2 GPRS
GPRS (General Packet Radio Service) is a packet oriented transmission service which is used in
the mobile networks and which is supported by almost all network providers.
With GPRS you only have a virtually existing permanent connection to the other party. Only
when you really transmit data will the channel will be used, otherwise it is free for other users.
This means that no channel will be reserved permanently for a user (as it is with a GSM voice
call). Therefore the GPRS-bills depend more on the actual data volume transmitted than on the
connect time.
If the device is booked into the GPRS-Net it will automatically be assigned an IP-Address and
can exchange data with any server accessible via the internet,
Before you can use the GPRS-Interface the SIM-Card must be activated for GPRS. To order this
functionality please talk to your mobile network provider.
2.3 Quadband Frequencies
When a device is “quadband” it means that it uses the four major GSM frequencies and that it
is compatible with most GSM networks worldwide.
These four frequencies are 850 MHz and 1900 MHz (on the American continent) and 900 MHz
and 1800 MHz, which are used in almost all other countries worldwide (Europe and Asia).
In contrast to a triband mobile phone which only supports 900/1800 and 1900 or 850/1800
and 1900 a quadband device can be used in almost every GSM network worldwide.
2.4 E-Mail via SMTP
SMTP (Simple Mail Transfer Protocol) is a method used to send e-mails over the internet. The
STD32 establishes a connection to an SMTP server which will send the e-mail to the given email address. The STD comes preconfigured with an E-Mail service subscribed by CEP. Please
note, however, that CEP does not maintain own infrastructure for the E-Mail service. Changes
in external services may take place at any time and are beyond our control. For more
information see chapter 8.
6
3
Operating Conditions














4
Operate the STD32 only with a supply voltage between 7-32V DC and have in mind the
polarity! (see picture1) Use a stabilized power supply with minimum 1A output current. (we
recommend to use only the original CEP power supply). If you use a mains adapter for
power supply it has to conform with the VDE regulations.
Devices with an operating voltage greater than 35 Volts which are connected to the relay
have to be installed by a specialist observing the VDE regulations.
Loads connected to the device are not allowed to exceed 1000 W per relay.
The maximum voltage of the outputs is 250 VAC (alternating current)
The maximum switching power per relay is 6 A (depending on the width of the PCB tracks)
When installing the device make sure that the supply cable has a sufficient diameter
During operation the temperature has to be between -20° and 55° Celsius.
Protect the device from humidity, spray water and heat.
In case of condensation allow a period of about 2 hours for acclimatization.
Do not operate the device in areas where inflammable gas, vapors, or dust are or could be
present.
Do not expose the device to heavy vibrations.
The unit may only be repaired by a specialist.
Only original parts have to be used when repairing the unit. The use of differing spare parts
can cause serious material loss or personal injury.
No special operation position of the device has to be observed.
Proper Use
The device is designed for the remote switching of devices via the GSM network as well as the
remote retrieval of status information of the inputs and the generation of SMS messages or emails after status has changed at the inputs. A different utilization of the device other than the
one described above is not allowed.
5
Introduction
The STD32 is a telemetry module which is easy to install and simple to use.
With the STD32 you can control two relays and monitor the status of two digital inputs with
one or several common mobile phones.
Apart from the STD32 you only need a valid SIM Card of any network provider (GSM850 / 900
/ 1800 or 1900 MHz)
While using prepaid SIM-cards one shall always keep aware of the amount of remaining credit
left on the card, so that in case of alarms a message can be sent.
Typical fields of application are



the opening of (garage) doors
switching on and off light and alarm devices as well as generating alarm messages (SMS or
e-mail)
the retrieval of information from door sensors, movement sensors or level sensors
You can for example open your garage door with a call or get a message (via SMS or e-mail) in
case your house alarm system gets triggered. In connection with the CEP camera you can get
a photo via e-mail
As shown in Figure 1 the STD 32 has 3 sets of connector terminals.
Pins 2 and 3 of the output connector are used to connect a device to the relay of output 1.
Pins 5 and 6 are the connections for the relay of output 2. Pins 1 and 4 are reserved and
should not be used.
On the input connector pins 2 and 4 are connected to the positive sides of the optocouplers for
inputs 1 and 2 respectively. Pins 1 and 3 are the negative sides of the same optocouplers.
When voltage is present across the optocouplers the inputs will be activated. Pins 5 and 6 are
reserved.
8
Power to the device is supplied VIN input and the GND input of the power connector.
The ANT connector is where the GSM antenna with FME-female should be attached.
LED Signals:
The Status and I/O LEDs are labelled on the PCB.
When the engine is booked into the GSM network the GSM LED flashes once every 2 seconds.
The status LEDs show the status of the inputs and outputs. RLY1 and RLY2 are on if the
corresponding relay is activated. OPT1 and OPT2 signal the status of the optocoupler inputs
IN1 and IN2.
The EXT LED is on as long as the camera is active.
The RD and GR system LEDs show the current system status and are described later on.
Please observe the maximum output voltage of the relays and the maximum input voltage of
the inputs! In chapter 3. “Operating Conditions” you will find further information on this.
6
Quick start up
In the following section it is described step by step what you have to do to administrate the
STD32 without long preparation.
6.1 General preparations
You need an activated SIM card of a GSM network provider. The PIN of this card has to be
deactivated or set to “0000”(4 times zero).
Alternatively you could use the PIN “2468”.
To change or deactivate the PIN you can use a common mobile phone. The instructions how to
change or deactivate the PIN are described in the manual of your mobile phone.
If you use a SIM card with a PIN different from “0000” or “2468” in the STD32, the
STD32 will use a “wrong” PIN. After the second attempt to power up the device
your SIM card will be blocked. In this case you need to use the “PUK” to assign a
new PIN to your card. Please look into the user guide of your mobile phone. There
you find how to use the PUK to de-block the SIM card.
Should you wish to use a SIM card which does not require a PIN, this is also possible and the
STD32 recognizes this and will behave accordingly.
In the following we will refer to the “master mobile” as the mobile telephone which you want
to use to switch the outputs and to configure the STD32 via calls.
To be able to administer the STD32 with your master mobile it is necessary that the “incognito”
or “private call” function of the mobile is deactivated. This means the master mobile has to
transmit the mobile telephone number with every call. To change the settings please refer to
the user guide of your mobile telephone.
To test the setting you can call a different mobile phone; there your phone number or name
should be displayed.
6.2 Hardware preparations
Before connecting the supply voltage to the STD32 please insert the SIM card into the SIM
card holder: To open the SIM card holder move it sideways and flip it open; insert the card
(mind the proper orientation of the card) and close it again. To lock it in place move the top
sideways in the opposite direction.
Now please connect the GSM antenna which is part of the delivery to the proper antenna
connector on the STD32 board.
After that connect the power supply
10
Please always observe the polarity (see picture 1) and that you have a proper power
supply. (see chapter 3.”Operating Conditions”)
6.3 Configuration Call
After having connected the power supply the green system LED will be illuminated for approx.
5 seconds (system start). Shortly after that the GSM LED will be activated. Now the STD32 will
automatically try to connect to the GSM network. As soon as this is done, the GSM LED will be
flashing once every 2 seconds.
As soon as the red and green system LED are toggling the STD32 is ready and waiting for the
configuration.
Now call with master mobile the phone number of the SIM card which is inside the STD32. The
STD32 will accept the call and cancel it a few seconds later. During this call, a four digit DTMF
sequence is sent to the caller and you will hear them on your mobile phone.
With this call the STD32 is configured to the master mobile.
Pay attention:
As long as the STD32 still has the factory defaults it shows this by the toggling the red and
green system LEDs. From this moment on you have three minutes to configure the STD32 with
the configuration call.
After 3 minutes (without configuration call done in between) the device switches off. If you
switch it on again afterwards the STD32 is again expecting the configuration.
In case the STD32 will be disconnected from the power supply after a successful configuration
by a power failure it will automatically send a SMS/E-mail with the text “START-UP ALARM” to
the preconfigured telephone number as soon as the power supply is established again.
6.4 Quick configuration check
To check whether the configuration was successful you can now make the following quick
configuration check.
Take your master mobile and call the telephone number of the SIM-Card inside the STD32.
This call should be cancelled by the STD32 and the Relay 1 should switch for one second
(watch LED L1 to see the status of the relay).
Now the basic configuration is done which means that all future events will be sent to the
master mobile and that Relay 1 can be switched from that mobile phone.
To use the additional functions of the STD32 please continue reading chapter 7 “Basic SMS
Commands”
7
Basic SMS Commands
7.1 Table of Basic Commands
Factory settings
R
Status of I/Os
ST?
Start-up alarm SMS on/off
S:1. / S:0.
Relay 1 on
O1ON.
Relay 1 off
O1OFF.
Relay 2 on
O2ON.
Relay 2 off
O2OFF.
Switching time Relay 1
O1:xxxxx. (seconds)
Switching time Relay 2
O2:xxxxx. (seconds)
Delay before reply (Relay 1) 0 = no message
A1:xxx. (seconds)
Delay before reply (Relay 2) 0 = no message
A2:xxx. (seconds)
Time of activation Input 1
I1:xxx. (seconds)
Time of activation Input 2
I2:xxx. (seconds)
Invert Input 1
V1:x. (x= 1/0 )
Invert Input 2
V2:x. (x= 1/0 )
2nd alarm number
C2:<number>.
3rd alarm number
C3:<number>.
4th alarm number
C4:<number>.
5th alarm number
C5:<number>.
new password
PN:xxxx.
event text 1
E1:<text>.
event text 2
E2:<text>.
Start-up alarm Text
PT:<text>.
add clip to the extended clip list
CL:<nummer>.
remove clip from the extended clip list
CD:<nummer>.
12
7.2 Send SMS Commands
By sending a SMS to the STD32 you can switch the outputs or make individual configuration
settings.
Those SMS have the following format which is described below:
In order to avoid unauthorized usage, every configuration command to the STD32 must start
with a 4-digit password. Control commands (for example: switching an output or status
requests) do not require a password.
The factory set password is the last four digits of the IMEI number of your STD32. You find
your devices IMEI printed on a sticker on the back of the housing.
The last four digits of the IMEI being the password for your device must always be kept a
secret. In this example the keyword is “4244”.
The IMEI cannot be changed! Although the password can be changed if needed for security
purposes, you should keep in mind that every command – including setting back to factory
settings – requires the knowledge of the password.
All commands (except R: and ST?) must end with a full stop “.”!
All commands can be sent in one SMS; each command has to be separated from the next by a
full stop (see examples).
Any command parameter that includes a full stop must be put in quotation marks (e.g.
“[email protected]”.).
The parameters for the seconds e.g. command “O1:xxxxx.” can have 1-5 digits. Valid
parameters are e.g. 1 (for 1 second), 90 (for 90 seconds) or 99999 for (99999 seconds). No
leading “zeros” have to be added. Example: “O1:110” stands for 110 seconds.
Please observe the difference between the figure ‘0’ and the letter ‘O’!. (“O1ON.”
contains twice the letter O; “V1:0.” contains once the figure 0)
A configuration command should look like the following example:
7.3 Explanation of the commands
Switching outputs via SMS


After the STD32 has received a SMS with the text “O1ON.” (Output 1 ON) from the
configured mobile phone, the relay 1 switches for one second. With the SMS “O2ON.” relay
2 switches for one second.
To get feedback of the actual status of the inputs and outputs just send a SMS with “ST?”
Configuration-SMS (attention 4-digit keyword required!)







The SMS “R:” is sets the STD32 back to the factory settings. Please note that this SMS can
be sent from any mobile phone as long as the 4-digit keyword is known. This ensures that
the STD32 can still be used even if the original master mobile (phone number) is no longer
available.
You can activate or deactivate the Start-up SMS (START-UP ALARM) with the SMS “S:x.” (x
= 1 or 0).
A SMS with the text “O1:xxxxx.” or “O2:xxxxx.” (xxxxx = seconds) configures the switching
time of the relays. The STD32 saves these settings so that they are still available after the
supply voltage has been restored.
If the switching time has been set to 0 by a configuration SMS the corresponding relay
switches permanently at every call. If the relay has been active before it will afterwards be
inactive
and
vice
versa.
In this case a SMS with the text “O1ON.” from the configured mobile phone switches the
relay 1 permanently on. A SMS with “O1OFF.” permanently switches off relay 1. Relay 2
reacts accordingly to SMS messages with “O2ON.” and “O2OFF.”.
The SMS “A1:xxx.” or “A2:xxx.” (x = seconds) sets the delay after which a reply SMS is sent
after an output has been activated. This can be helpful if you want to switch something on
or off and would like to measure the result of this output control with one of the inputs of
the STD32. Therefore the new status after the switching of the output is transmitted.
With a SMS containing the text “I1:xxx.” or “I2:xxx.” (xxx = seconds) you can configure the
time the inputs have to be activated before the STD32 sends out an alarm SMS
A SMS with the text “V1:x.” or “V2:x.” (x = 1 or 0) can change the polarity of the inputs. If
x=1 an alarm SMS will be sent in case the input has not been activated for the configured
time. The default value is x=0 which means that the STD32 will send an event alarm in
case the input has been activated longer than the configured time
Please note that the brackets “<“ and “>“in the following commands are not part of the
commands but are included in order to increase the readability of the overview!
Four additional alarm numbers (mobile phones) can be defined using C2: - C5: commands.
These numbers are allowed to set relay 1 by a call and they are informed via SMS in case of
Start-up or events. These numbers are not allowed to send configuration SMS messages.
If an alarm number is given in international format, the number must start with ‘+’.
(e.g. +491721234567)



With the “PN:<4digit password>.” command the password can be changed. The password
can include letters and figures but no special characters are allowed. All letters have to be
in capital. The standard password (factory setting) is the last 4 digits of the IMEI (see
chapter SMS Commands).
The texts of the event or start-up SMS can be changed with the commands “E1:<text1>.”,
“E2:<text2>.” and “PT:<startup text>.”. The message length must not exceed 64
characters. Do not use command syntax inside a message text. The ‘.’ is the
terminating character of the text. Each new text must be sent in a separate SMS.
If you have to use punctuation in the event text, use quotation marks at the beginning and
at the end of the event text. For example:
1234 E1:"Example Event 1.".
You can generate an extended clip list of 1000 clip numbers. The numbers stored in the clip
list are allowed to switch relay 1 with a phone call. Use “CL:” to generate the clip list and
add further phone numbers. With “CD:” you can delete a phone number from the list. Be
aware that you cannot read out the clip list (getting SMS messages) because it could by far
14

exceed the size limitation of SMS texts. If an asterisk “*“ is added to the clip list, any
incoming call will trigger relay 1.
The ST? command reads out the current status of the device including all inputs and
outputs. Most settings cannot be read back from the device remotely and without the
configuration tool.
Please note that all commands listed in the section “Configuration SMS” require the 4-digit
keyword at the beginning.
7.4 Examples for SMS Commands
Please note that for these examples the 4-digit password 4244 has been chosen.
Instead of this password you have to use your 4-digit password of your STD32!
Start-up alarm off, relay 1 on, relay 2 off, time of 4244 S:0.O1ON.O2OFF.I1:5.
activation of input 1: 5 sec
Switching time of relay 1 = 90 seconds
4244 O1:90.
Reset settings to factory settings
4244 R:
Configuration of the second alarm number
4244 C2:+491721234567.
Deleting a alarm number
4244 C2:.
Configuration of a new password
4244 PN:AB12.
Adding a new clip to the extended clip list
4244 CL:+491721234567.
Removing the clip from the extended clip list:
4244 CD:+491721234567.
8
E-Mail functionality via GPRS
Netzbetreiber z.B Vodafone
Internet
SMTP E-Mail Server z.B. AOL
IP
Port
Benutzername
Passwort
APN
Benutzername
Passwort
STD32
The STD32 offers you the possibility to get messages via SMS and via e-mail.
8.1 Configuration of the E-Mail functionality
If you need a full stop "." in a parameter as it is for example in an e-mail address, the
complete parameter has to be put into quotation marks (“...”) (e.g. "[email protected]"),
otherwise the "." would be seen as the end of the command.
Additionally you have to take care to send the 4-digit keyword at the beginning of each
configuration SMS.
To be able to use the e-mail functionality the following parameters have to be set.
GPRS settings
(to set up an internet connection)

Name of the APN (Access Point Name)
APN:<text>.
User name for APN
APNUSR:<text>.
Password for APN
APNPWD:<text>.
With the commands “APN:<text>.”, “APNUSR:<text>.” and “APNPWD:<text>.” you make
the basic settings to build up a GPRS (internet) connection. You need to get the necessary
data from your GSM network provider
Example (Vodafone, Germany):
The GSM network provider Vodafone gives you the following details:
APN: web.vodafone.de
User: vodafone
Password: vodafone
16
Thus you would have to send the following SMS:
Username
4244APN: „web.vodafone.de“.APNUSR:vodafone.APNPWD:vodafone.
APN
Password
SMTP settings
(to send e-mails)
IP- Address of the SMTP Server
SMTPIP:<text>.
Port of the SMTP Server
SMTPPORT:xxxxx.
User name for SMTP Server
SMTPUSR:<text>.
User password for SMTP Server
SMTPPWD:<text>.
In most cases it is not necessary to configure any of the SMTP settings as the
device come preconfigured for the e-mail server subscribed by CEP, which is a
free service for STD32 users. If the user wishes to use another server it must
support plain text authentication. CEP does not maintain a list of mail providers
the support plain text authentication, this information must come the provider
of the mail server.
As noted in Section 2.4 E-Mail via SMTP, CEP does not maintain own
infrastructure for the E-Mail service. Changes in external services may take
place at any time and are beyond our control.
Specific settings:
Recipient for e-mail transmission
Recipient e-mail address

TO:<text>.
With the command “TO:<text>.” you define the recipient e-mail address. You can list up to
5 e-mail addresses each separated by a <;>. The max. length per e-mail address is 75
characters. Default status: no e-mail address is entered. If at least one e-mail address is
defined an e-mail transmission is started at following events: start up, input1, input 2.
8.2 Additional E-Mail configuration possibilities
You can make further configuration settings for the e-mail functionality. With the following
commands you can define e-mail recipients who should only get an e-mail in case of a certain
event. For every event there can be a different email recipient.
Event 1 (Input1)
Recipient e-mail address
TO1:<text>.
Subject line of the e-mail
SUB1:<text>.
Body of the e-mail
BODY1:<text>.
Event 2 (Input2)
Recipient e-mail address
TO2:<text>.
Subject line of the e-mail
SUB2:<text>.
Body of the e-mail
BODY2:<text>.
Start Up Event
Recipient e-mail address
TO3:<text>.
Subject line of the e-mail
SUB3:<text>.
Body of the e-mail
BODY3:<text>.
Incoming Call Event
Recipient e-mail address
TO4:<text>.
Subject line of the e-mail
SUB4:<text>.
Body of the e-mail
BODY4:<text>.
Photo SMS Event


Recipient e-mail address
TO5:<text>.
Subject line of the e-mail
SUB5:<text>.
Body of the e-mail
BODY5:<text>.
With the command “TOx:<text>.” (x = 1 to 5 see above) you define the recipient e-mail
address (only for this event). You can list up to 5 e-mail addresses each separated by a
<;>. The max. length per e-mail address is 75 characters. Default status: no e-mail address
is entered.
With the command “SUBx:<text>.” (x = 1 to 5 see above) the subject line of the e-mail
is defined. The max. length is 128 characters per text. The default value is "STD32 x event"
18

You can define the body text of the e-mail with the command “BODYx:<text>.” (x = 1 to
5 see above). The max. length is 160 characters per body text. The default value is
empty, meaning no text is sent.
Additional settings










Senders e-mail address
FROM:<text>.
Priority of the e-mail
PRIO:<x>.
E-mail as HTML or Text
HTML:<x>.
E-mail code
CHARSET:text>.
Sender in subject line
FROMSUB:text>.
Send attachment
ATT:<x>.
E-mail address in CC
CC:<text>.
E-mail adress in BCC
BC:<text>.
Request picture via SMS
PHOTO.
Activate camera (on/off)
CAM:<x>.
With the command “FROM:<text>.” you can configure the sender e-mail address. The max.
length is 75 characters.
“PRIO:<x>.” sets the priority with which the e-mail will be displayed. Possible values are
from 1 to 5. The default value is 3 (normal priority).
With the command “HTML:<x>.” you can define whether the e-mail should be sent as a
HTML message or as a text message (1 = HTML and 0 = text). The default value is 0.
With the command “CHARSET:text>.” you indicate with which coding the e-mail will be
sent. The default value is "UTF-8". Normally you do not have to change this.
If you want to enter the sender into the subject line you have to send the command
“FROMSUB:text>.”. The max. length is 75 characters. No senders e-mail address is entered
here as default value.
With the command “ATT:<x>.” you can configure whether an attachment should be send
or not (1 = send attachment, 0 = no attachment). The default value is 1 (send
attachment).
If you want to put a recipient on CC (Carbon Copy) you can do this with the command
“CC:<text>.”. The max. length is 75 characters. No e-mail addresses are entered as a
default value.
To put a recipient in BCC (Blind Carbon Copy) use the command “BC:<text>.”. The max.
length is 75 characters.. No BCC e-mail addresses are entered as a default value
To make a picture and send it via e-mail send the SMS command “PHOTO.”.
You can deactivate the camera functionality when the camera is connected to the STD32
with the command “CAM:0.” and activate it with “CAM:x.”. The camera offers different
resolutions and you can select the desired camera resolution (x):
1 = 80 x 60
3 =160 x 120
5 = 320 x 240
7 = 640 x 480
The default value is 0.
20
9
Complete list of commands
Configuration Commands
R:
reset default device settings
ST?
request device status SMS
S:
1 - enable startup SMS
0 - disable startup SMS
M1: set phone number nr 1 (change master number)
C2:
set phone number nr 2
C3:
set phone number nr 3
C4:
set phone number nr 4
C5:
set phone number nr 5
PN:
set different password (max 4)
E1:
set message text for INPUT 1 event (max 64)
E2:
set message text for INPUT 2 event (max 64)
PT:
set message text for POWER-UP event (max 64)
Inputs & Outputs commands
O1ON
turn relay 1 on
O1OFF
turn relay 1 off
O2ON
turn relay 2 on
O2OFF
turn relay 2 off
O1:xxxxx
defines time period for relay 1 action (in seconds)
O2:xxxxx
defines time period for relay 2 action (in seconds)
A1:xxxxx
Delay before reply (Relay 1) 0 = no message
A2:xxxxx
Delay before reply (Relay 2) 0 = no message
I1:xxx
debounce time for input 1 (in seconds)
I2:xxx
debounce time for input 2 (in seconds)
P1:xxx
Event counter for input 1 (after xxx Input Events, a Message
is sent)
P2:xxx
Event counter for input 2 (after xxx Input Events, a Message
is sent)
V1:x
1 - invert input 1
0 - normal input 1
V2:x
1 - invert input 2
0 - normal input 2
CLIP commands
CL:
add clip list number, asterisk symbol (*) is also supported
CD:
remove clip list number
DATA commands
EMAIL:
1 - enable email feature
0 - disable email feature
default is enabled
SMTPIP:XXXXX defines SMTP server IPv4 address
example SMTPIP:"smtp.aol.com"
max length is 32
SMTPPORT:
defines SMTP server PORT
example SMTPPORT:2121
value must be a number, in range 0..
default is 25
APN:
defines GPRS APN (for emails)
example APN:internet
max length is 32
default is internet
APNUSR:
defines GPRS USERNAME (for emails)
example APNUSR:Patryk
max length is 32
default is empty
APNPWD:
defines GPRS PASSWORD (for email)
example APNPWD:Patryk
max length is 32
default is empty
SMTPUSR:
defines smtp username (used for authentication - this is
22
not APN username!)
example SMTPUSR:"p.szymczak"
max length is 64 (according to RFC0821, chapter 4.5.3.
SIZES)
default is empty
SMTPPWD:
defines smtp password (used for authentication - this is
not APN password!)
example SMTPPWD:"p.szymczak"
max length is 64 (according to RFC0821, chapter 4.5.3.
SIZES)
default is empty
FROM:
defines email sender
example FROM:"[email protected]"
max length is 25
default is empty
TO:
defines up to 5 email recipients (separated by ";"), each
one max 25 characters
example TO:"[email protected]"
max length of field is 129 [(5*25+1)-1]
default is empty
TO1:
defines recipient address for INPUT 1 event
SUB1:
defines email subject that will be sent to "TO1" address
TO2:
defines recipient address for INPUT 2 event
SUB2:
defines email subject that will be sent to "TO2" address
TO3:
defines recipient address for STARTUP event
SUB3:
defines email subject that will be sent to "TO3" address
TO4:
defines recipient address for CALL event
SUB4:
defines email subject that will be sent to "TO4" address
TO5:
defines recipient address for PHOTO event
SUB5:
defines email subject that will be sent to "TO5" address
TO6:
defines recipient address for MOTION event
SUB6:
defines email subject that will be sent to "TO6" address
TO7:
defines additional recipient address for STATIONARY
event
SUB7:
defines email subject that will be sent to "TO7" address
BODY:
defines general body
substitution variables
content
that
can
contain
Camera commands
CAM:
0 - disable camera feature
1 - enable camera feature with photo size 80×64
3 - enable camera feature with photo size 160×128
5 - enable camera feature with photo size 320×240
7 - enable camera feature with photo size 640×480
default is 7 - enabled, with the biggest photo size
PHOTO
used without any parameters, triggers email with cam photo
sending
DOTA commands
DOTAAPN:internet.DOTAAPNUSR:"".DOTAAPNPWD:"".DOTAREQ.
DOTAUSR:
set FTP username (max 16)
DOTAPWD:
set FTP password (max 16)
DOTASERVER:
set FTP server IPv4 or domain (max 64)
DOTAFILE:
set filename (max 64)
DOTAAPN:
set APN (max 24)
DOTAAPNUSR:
set APN username (max 12)
DOTAAPNPWD: set APN password (max 12)
DOTAREQ
trigger DOTA
For Information about software update with DOTA (Download Over The Air) please contact our
Support ([email protected])
24
Misc commands
VERSION?:
requests current software version
10 Connecting the camera
The STD35 is offers the possibility to monitor an object or a room with the help of the CEP
camera optional accessory for the STD35
A picture can be sent as an attachment to the preconfigured e-mail address in the case of an
alarm. This allows you to take further action if necessary (e.g. call the police if you see a
burglar on the photo)
To be able to use this functionality you only have to connect the CEP camera to the camera
plug on the STD35 (see picture 1) and to activate the email-feature and the camera.
After the software of the STD35 has recognized the camera the pictures can be sent via e-mail
in the following ways:



E-mail with JPEG attachment in alarm situation
E-mail with JPEG attachment after incoming call
E-mail with JPEG attachment after SMS request
In case the light intensity is not enough at the survey area the infrared light of the camera will
be activated automatically. Please note that due to the infrared light there will be a loss of
colors in the picture.
The CEP camera has an adjustable sun shade (metal plate over the camera). Please take into
consideration when adjusting the sun shade that the insolation is changing during the day.
TIP:
To make sure that all desired objects will be in the picture, that
the sun shade is in a good position and/or that the illumination
of the room will lead to satisfactory picture we recommend to
take “test pictures” after the installation. Only then you can rely
on the full functionality of the CEP camera.
26
11 Configuration Tool
Besides configuring The STD35 via SMS, or using a configuration call it is possible to use the
CEP configuration tool to implement all setting. This tool allows the user to connect the device
to a standard PC via a special STDx accessory cable.
Once the cable is connected the STD35 can be monitored and completely configured using the
software provided. The configuration tool allows the user to configure devices without having
to manually construct SMS commands or send any SMS to the device. You will get further
information via [email protected]
12 Troubleshooting
Problem
Possible Reason
Solution
GSM LED stays dark
No supply voltage-
Connect power supply
GSM
LED
cyclically
blinks
twice No SIM card / Improper Insert SIM card properly or
contact with SIM card
carefully clean contact area of
SIM card
GSM LED
cyclically
blinks
thrice PIN is not “0000”
Change SIM card’s PIN to “0000”
GSM LED constantly on
No
GSM
network Connect antenna /
available / no antenna
Change antenna position
connected
GSM LED dies after 3 minutes
No configuration
STD32 does not react on Device
is
configuration
call
(not configured
accepting the call)
Make configuration call
already Set back to factory settings
STD32 does not react to a Wrong IMEI number in Check IMEI number. / Wait until
configuration SMS
the SMS / SMS not yet SMS is delivered
delivered
STD32 does not react to an The mobile phone does Activate the transmission of the
SMS, or call, although booked not transmit the phone phone number in your mobile
to the network
number (“Incognito”)
phone
System LEDs toggle
No configuration
received by STD32
28
call Make configuration call
13 Accessories
CEP AG is offering accessory parts for the STD32 which have been thoroughly tested to work
with the STD32 and which have been approved for the use with the STD32. Therefore we
strongly recommend to use only accessory parts of CEP AG. The warranty will be null and void
if you use other than the original CEP accessory parts.
Please contact your supplier or CEP AG regarding the original accessory parts. The
recommended accessory parts mainly consist of :
GSM – magnetic antenna
-Part-Number 12021
FME – female connector and 2,5m cable
GSM – roof mount antenna
-Part – Number 12006
FME – female connector,
3m cable, waterproof
Configuration Tool & Cable
-Part Number 16212
STD35 accessory connector
14 Technical data









GSM: Quad Band EGSM 850/900/1800/1900 MHz
Compatible with ETSI GSM Phase 2 + Standard
Output power:
Class 4 (2W @ 850/900 MHz)
Class 1 (1W @ 1800/1900 MHz)
Temperature range: -20°C - +55°C
Weight approx. 220 grams
Dimensions: 150x65x45 mm (lxwxh)
Supply voltage: 7-32V
Idle current:15mA, peak up to 1.8A
Max. output current: 6A
Max. output voltage: 250V AC
Input voltage (digital inputs)
logic 1 (threshold >7V): max 32V
logic 0 (threshold <1,5V) :
min 0V
In case of technical problems or questions concerning the STD32,
please get in contact with your STD32 reseller.
For all other questions please call:
Sales: +49 (0) 89 / 4902686-0
30
15 Document history
Revision
Datum
Changes
Rev. 01
2nd March 2009
Completely new version
Rev. 02
23rd March 2009
Delta translations, camera
resolution
Rev 1.0
21st March 2012
Updated for new STD32
Rev 1.1
11th December
2013
Rev 1.2
21st February 2014
Updates to sections 2.4 & 8.
Imprint
These operating instructions are published by CEP AG
No reproduction (including translation) is permitted in whole or part e.g. photocopy,
microfilming or storage in electronic data processing equipment, without the express written
consent of the publisher.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
© Copyright 2014 by CEP AG
CEP AG
Raiffeisenallee 12b
D-82041 Oberhaching
Germany
www.cepag.de
CEP reserves the right to change, correct and/or improve the content any time and without
prior notice without being obliged to do so. No responsibility is taken for the correctness of the
information.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement