User manual M2
User manual M2
Setpoint generator
0…10 V; 0…20 mA
optional with switching points
Device performance:
• red display of -19999…99999 digits (optional: green, orange, blue)
• minimal installation depth: 70 mm without plug-in terminal
• definable adjustment for the setpoint
• configurable output area between 0…10 V or 0…20 mA
• adjustable increments per keystroke
• display flashing at limit exceedance / limit undercut
• digital inputs for key switch or external adjusting keys
• zero-key for quick recall of a default value
• configurable code as adjustment protection for the setpoint
• different operation options for the adjustment of the setpoint
• optional starting performance with last adjustment value or default value
• optional speed levels for the adjustment of the setpoint
• quick reaction during adjustment of the setpoint value (Ramp function)
• programming lock via code entry
• protection class IP65 at the front
• plug-in srew terminal
• optional 2 relay outputs (Changer)
• accessories: PC-based configuration-kit PM-TOOL with CD & USB-adapter for devices
without keypad and for a simple adjustment of standard device
M2_1GGB.pdf update: 28.03.2014
96x48
Identification
STANDARD-TYPES
Setpoint generator
Housing size: 96x48 mm
ORDER NUMBER
M2-1GR5B.00X0.570CD
M2-1GR5B.00X0.670CD
Options – break-down of order code:
M 2- 1 G R 5 B. 0 0 X 0. 6 7 0 C D
Standard type M-line
Dimension
D physical unit
Installation depth
incl. plug-in terminal 89 mm
2
Version
C C
Housing size
B96xH48xD70 mm
1
Type of display
Setpoint generator
Switching points
0 no switching points
2 2 relay outputs
G
Protection class
1 without keypad,
operation on the back
7 IP65 / pluggable terminal
Display colour
Blue
Green
Red
Yellow
B
G
R
Y
Number of digits
5-digits
5
Supply voltage
4 115 VAC
5 230 VAC
6 10-30 VDC galv.insulated
14 mm
B
Measuring input
0 without
Digital input
without
0
Analog output
X 0-10 VDC, 0/4-20 mA
Digit height
Sensor supply
0 without
Please state physical unit by order, e.g. m/min
Contents
1.
Brief description
2
2.
Assembly
3
3.
Electrical connection
4
4.
Functions and operation description
6
4.1. Programming software PM-TOOL
7
Setting up the device
8
5.1. Switching on
8
5.2. Standard parameterisation (flat operation level)
8
5.
Value assigment for triggering of the singal output
5.3. Programming interlock „RUN“
11
Activation/Deactivation of the programming interlock or change into the professional level
respectively back into the flat operation level
5.4. Extended parameterisation (professional operation level)
5.4.1. Signal input parameter „INP“
11
11
Value assigment for setpoint, triggering of digital inputs and assignment of keys, as well as
the behaviour at device start
5.4.2. General device parameter „FCT“
14
Adjustment of the optical alarm (display flashing)
5.4.3. Safety parameter „COD“
14
Assignment of user and master code for locking or access to certain
parameters like e.g. analog output and alarms, etc.
5.4.4. Analog output parameter „Out“
16
Analog output functions
5.4.5. Relay functions „rel“
17
Parameter for the definition of the setpoints
5.4.6. Alarm parameter „AL1…AL4“
19
Activator and dependencies of the alarms
6.
Reset to factory settings
20
Reset of the parameter to the factory default settings
7.
Alarms / Relays
21
Function principle of the switching outputs
8.
Technical data
22
9.
Safety advices
24
10.
Error elimination
25
1
1. Brief description
1. Brief description
Setpoint function
A setpoint generator enables the user to adjust operating parameters of a machine (like e.g. an oven
temperature, rotational speed or filling weight) in the most easiest way and relays it via the integrated
outputs to a superior control. Thereby the production engineer can determine the adjustment range and
thus guarantee a safe operation. This makes the setpoint generator an ideal device for simple control with
a few parameter or for a more complex regulation, where a simple relation between setpoint value and the
machine behavior that needs to be controlled is not possible (e.g. the filling weight of an ampoule filling
system).
For the setpoint generator the display value is changed manually by the user, depending on the adjustment
type via the front keys or via the digital inputs. The possible adjustment range is definable via the
parameters End and Offs. An output quantity Out.ra with the output range Out.En to Out.OF is allocated to
them. By changing the setpoint in the display, the initial value is linear and carried isochronous. The
following values result from a adjustment range of the setpoint from 0…2000 and an accordingly selected
output range from 4…20 mA:
4 mA = 0
12 mA = 1000
20 mA = 2000
Additionally alarms and relays can be used to warn the user about critical settings or to activate an change
of operation mode, depending on the setpoiont.
To secure the favoured setpoint against accidental adjustment, a releasing code S.Code can be activated or
an electric key-switch can be provided. If an external key-switch is used via digital input 1, then the device
shows a –LOC– in the display by any attempt of adjustment via the keys [▲] [▼].
By operating the setpoint via the front keys, a default value/initial value start can be recalled via the [O]–
key. It can be used for one system as emergency switch, too.
This initial value is loaded in the basic setting during system start and displayed. If L.star was selected
instead of l.save as reset behaviour reset, the device loads up the last adjusted effective setpoint. The latter
is safed approx. 1 minute after each change of the setpoint.
The two excisting digital inputs react depending on the setting of in.lev to a HiGh- or a Low- signal.
2
2. Assembly
2. Assembly
Please read the Safety advice on page 24 before installation and keep this user manual for future reference.
3,0
48,0
M2
Se
alin
g
ion
llat
a
t
Ins
1.
2.
3.
,0
89
l.
inc
th
p
de
l
ina
erm
t
n
g-i
plu
After removing the fixing elements, insert the device.
Check the seal to make sure it fits securely.
Click the fixing elements back into place and tighten the clamping screws by hand. Then use a
screwdriver to tighten them another half a turn.
CAUTION! The torque should not exceed 0.1 Nm!
The dimension symbols can be exchanged before installation via a channel on the side!
3
3. Electrical connections
3. Electrical connections
Type M2-1GR5B.00X0.470CD supply of 115 VAC
Type M2-1GR5B.00X0.570CD supply of 230 VAC
Type M2-1GR5B.00X0.670CD with a supply of 10-30 VDC
4
3. Electrical connections
M2 devices with frequency input/ pulse input
5
4. Function and operation description
4. Function and operation description
Operation
The operation is divided into three different levels.
Menu level (delivery status)
This level is for the standard settings of the device. Only menu items which are sufficent to set the device
into operation are displayed. To get into the professional level, run through the menu level and
parameterise “prof“ under menu item RUN.
Menu group level (complete function volume)
Suited for complex applications as e.g. linkage of alarms, setpoint treatment, totaliser function etc. In this
level function groups which allow an extended parameterisation of the standard settings are availabe. To
leave the menu group level, run through this level and parameterise „uloc„ under menu item RUN.
Parameterisation level:
Parameter deposited in the menu item can here be parameterised. Functions, that can be changed or
adjusted, are always signalised by a flashing of the display. Settings that are made in the parameterisation
level are confirmed with [P] and thus safed. Pressing the [O]-key (zero-key) leads to a break-off of the
value input and to a change into the menu level. All adjustments are safed automatically by the device and
it changes into operating mode, if no further key operation is done within the next 10 seconds.
Level
Key
Description
Change to parameterisation level and deposited values.
Menu level
Keys for up and down navigation in the menu level.
Change into operation mode.
To confirm the changes made at the parameterization level.
Parameterisation level
Adjustment of the value / the setting.
Change into menu level or break-off in value input.
Change to menu level.
Menu group level
Keys for up and down navigation in the menu group level.
Change into operation mode or back into menu level.
6
4. Function and operation description
Function chart:
4.1 Parameterisation software PM-TOOL:
Part of the PM-TOOL are the software on CD and an USB-cable with device adapter. The connection is
done via a 4-pole micromatch-plug on the back side of the device, to the PC-side the connection happens
via an USB plug.
System requirements: PC incl. USB interface
Software: Windows XP, Windows VISTA
With this tool the device configuration can be generated, omitted and safed on the PC. The parameters can
be changed via the easy to handle program surface, whereat the operating mode and the possible selection
options can be preset by the program.
7
5. Setting up the device
5. Setting up the device
5.1. Switching-on
Once the installation is complete, you can start the device by applying the voltage supply. Before, check once
again that all electrical connections are correct.
Starting sequence
For 1 second during the switching-on process, the segment test (8 8 8 8 8) is displayed followed by an indication
of the software type and, after that, also for 1 second the software version. After the starting sequence, the
device switches to operation/display mode.
5.2. Standard parameterisation: (flat operation level)
To parameterize the display, press the [P]-key in operating mode for 1 second. The display then changes to the
menu level with the first menu item TYPE.
Menu level
Parameterisation level
Selection of the adjustment type for the setpoint / default value, TYPE:
Default: f.tast
With F.tASt the setpoint is adjusted by [▲] [▼], furthermore the adjusment can be locked via
the external input 1. At F.InPu there is a direct selective input of the setpoint via [P] [▲] [▼]. For
the adjustment [▲] or [▼] needs to be pressed first. Via input 1 the adjustment lock is
controlled. With E.tASt the adjustment of the setpoint via the external inputs 1 (+) and 2 (-) is
done. There is no additional input lock. This has to be realised by an electrical connection of the
keys if required. Confirm the selection with [P] and the display switches back to menu level.
Setting up the adjustment end value, END:
Default: 10000
Set the end value from the smallest to the highest digit with [▲] [▼] and confirm each digit with
[P]. A minus sign can only be parameterized on the leftmost digit. After the last digit, the display
switches back to the menu level. The value that is set here, can later on not be exceeded while
adjusting the setpoint.
Setting up the adjustment start/offset value, offs:
Default: 0
Enter the start/offset value from the smallest to the highest digit with [▲] [▼] and confirm each
digit with [P]. A minus sign can only be parameterized on the leftmost digit. After the last digit
the display switches back to the menu level. The value that is set here, can later on not be
undercut while adjusting the setpoint.
Setting up the adjustment initial value, StArt:
Default: 0
The initial value, which is loaded by start or on [O], is adjusted from the smallest to the highest
digit with [▲] [▼] and confirmed digit per digit with [P]. A minus sign can only be parameterized on the leftmost digit. After the last digit the display changes back into menu level.
8
5. Setting up the device
Menu level
Parameterisation level
Setting up the increments, Step:
Default: 1
The increments for the adjustment types F.tast and E.Tast are adjusted from the smallest to the
highest digit with [▲] [▼] and confirmed digit per digit with [P]. After the last digit the display
changes back into menu level. Per keystroke the setpoint is changed by the increment, which
can be selected from 1…99999.
Maximum possible change acceleration, speed:
Default: pace.i
Via speed the maximum possible change accleration of the setpoint in permanent activation of
up or down can be set. At Pace.1 no multiplication of the increment takes place. For each other
Pace-step the maximum speed muliplies tenfold to pace.4 with factor 1000. The change
acceleration is gradually increased at permanent active up or down.
Setting the decimal point, dot:
Default: 0
The decimal point on the display can be moved with [▲] [▼] and confirmed with [P]. The
display then switches back to the menu level again. The adjusted decimal point has no
influence on the increment and is displayed without additional dependency.
Setting up the switching-on behaviour, reset:
Default: l.star
With this parameter the setpoint behaviour after the switching-on of the device can be selected
by [▲] [▼] and confirmed with [P]. With L.save the last effective setting is taken over as
setpoint during switching-on, the change is taken over after 30 seconds and is then available as
initial value. At L.StAr the defined initial value Start is loaded.
Setting the active input level, In.lev:
Default: HIGH
The active input level can be adjusted to low or high with [▲] [▼]. With [P] the selection is
confirmed and the display changes back into menu level. This is a very important setting, as it
is used for all operation types type!
Setting the code for the adjustment lock, s.code:
Default: 0000
The code for the adjustment lock is adjusted from the smallest to the highest digit with [▲] [▼]
and confirmed digit per digit with [P]. After the last digit the display changes back into menu
level. If the s.code is set on a value unequal 0000, the code lock is activated for type, F.tast and
f.inpu. This means at each adjustment attempt the enable code s.code is recalled. For typesettings E.tast the enable code s.code has no meaning.
9
5. Setting up the device
Menu level
Parameterisation level
Selection of analog output, Out.rA:
Default: 0-10
Two output signals are available: 0-10 VDC and 0-20 mA. They can be selected with [▲] [▼]
and are confirmed digit by digit with [P]. The output area can be limited via OUT.En and out.of to
e.g. 4-20 mA.
Setting up the output-final value, Out.En:
Default: 10.000
The output-final value is adjusted from the smallest digit to the highest digit with [▲] [▼] and
digit by digit confirmed with [P]. After the last digit the display changes back into menu level.
Depending on the output signal out.ra, the value relates to a voltage between 0…10 V or a
current between 0…20 mA and is reached, if the adjustment final value END is reached as
setpoint.
Setting up the initial value of the analog output, Out.OF:
Default: 00.000
The output-initial value is adjusted from the smallest digit to the highest digit with [▲] [▼] and
digit by digit confirmed with [P]. After the last digit the device changes back into menu level.
Depending on the output signal out.ra, the value relates to a voltage between 0…10 V or a
current between 0…20 mA and is reached, if the adjustment initial value offs is reached as
setpoint
User code (4-digit number-combination free available), U.CodE:
Default: 0000
With this code (>0000), all parameters are locked, if LOC was selected under menu item run
before. By pushing [P] for approx. 3 seconds during operation mode, the message Code
appears in the display. To get to the reduced parameters that were activated for the user, the
preset U.Code needs to be entered. This code has to be entered before each attempt of
parameterisation, until the A.Code (Master code) activates all parameters again.
Master code (4-digit number-combination free available), A.CodE:
Default: 1234
This code can activate all parameters, after LOC has been activated under menu item run
before. By pushing [P] for approx. 3 seconds during operation mode, the message Code
appears in the display and thus enables the user to reach all parameters by entering the A.codE.
Under run the parameterisation can be activated permanently by selecting ULOC or ProF, thus at
an anew pushing of [P] in operation mode, the code needs not to be entered again.
10
5. Setting up the device
Menu level
Parameterisation level
5.3. Programming interlock
Activation / Deactivation of the programming interlock or completion of the standard
parameterisation with change into menu group level (complete function volume), run:
Default: uloc
Choose between the deactivated key lock Uloc (works setting), the activated key lock Loc, or the
menu group level ProF with the navigation keys [▲] [▼]. Confirm the selection with [P]. After
this, the display confirms the settings with "- - - - -", and automatically switches to operating
mode. If Loc was selected, the keyboard is locked. To get back into the menu level, press [P]
for 3 seconds in operating mode. Now enter the CODE (works setting 1234) that appears using
[▲] [▼] plus [P] to unlock the keyboard. FAIL appears if the input is wrong.
To parameterise further functions, ProF needs to be set. The device confirms this setting with
„- - - - - „ and changes automatically into operation mode. By pressing [P] for approx. 3 seconds
in operation mode, the first menu group InP is shown in the display and thus confirms the
change into the extended parameterisation. It stays as long activated as ULOC is entered in
menu group RUN, thus the display is set back in standard parameterisation again.
5.4. Extended parameterisation (professional operation level)
5.4.1. Signal input parameters
Menu group level
Menu level
Menu level
Parameterisation level
Selection of the adjustment type for the setpoint / default value, TYPE:
Default: f.tast
With F.tASt the setpoint is adjusted by [▲] [▼], furthermore the adjustment can be locked via
the external input 1. At F.InPu there is a direct selective input of the setpoint via [P] [▲] [▼]. For
the adjustment [▲] or [▼] needs to be pressed first. Via input 1 the adjustment lock is
controlled. With E.tASt the adjustment of the setpoint via the external inputs 1 (+) and 2 (-) is
done. There is no additional input lock. This has to be realised by an electrical connection ot the
keys if required. Confirm the selection with [P] and the display switches back to menu level.
11
5. Setting up the device
Menu level
Parameterisation level
Setting up the adjustment end value, END:
Default: 10000
Set the end value from the smallest to the highest digit with [▲] [▼] and confirm each digit with
[P]. A minus sign can only be parameterized on the leftmost digit. After the last digit, the display
switches back to the menu level. The value that is set here, can later on not be exceeded while
adjusting the setpoint.
Setting up the adjustment start/offset value, offs:
Default: 0
Enter the start/offset value from the smallest to the highest digit with [▲] [▼] and confirm each
digit with [P]. A minus sign can only be parameterized on the leftmost digit. After the last digit
the display switches back to the menu level. The value that is set here, can later on not be
undercut while adjusting the setpoint.
Setting up the adjustment initial value, StArt:
Default: o
The initial value, which is loaded by start or on [O], is adjusted from the smallest to the highest
digit with [▲] [▼] and confirmed digit per digit with [P]. A minus sign can only be parameterized on the leftmost digit. After the last digit the display changes back into menu level.
Setting up the increments, Step:
Default: 1
The increments for the adjustment types F.tast and E.Tast are adjusted from the smallest to the
highest digit with [▲] [▼] and confirmed digit per digit with [P]. After the last digit the display
changes back into menu level. Per keystroke the setpoint is changed by the increment, which
can be selected from 1…99999.
Maximum possible change acceleration, speed:
Default: pace.4
Via speed the maximum possible change accleration of the setpoint in permanent activation of
up or down can be set. At Pace.1 no multiplication of the increment takes place. For each other
Pace-step the maximum speed muliplies tenfold to pace.4 with factor 1000. The change
acceleration is gradually increased at permanent active up or down.
12
5. Setting up the device
Menu level
Parameterisation level
Setting the decimal point, dot:
Default: o
The decimal point on the display can be moved with [▲] [▼] and it is confirmed with [P]. The
display then switches back to the menu level again. The adjusted decimal point has no
influence on the increment and is displayed without additional dependency.
Setting up the switching-on behaviour, reset:
Default: l.star
With this parameter the setpoint behaviour after the switching-on of the device can be selected
by [▲] [▼] and confirmed with [P]. With L.save the last effective setting is taken over as
setpoint during switching-on. At L.StAr the defined initial value Start is loaded.
Setting the active input level, In.lev:
Default: high
The active input level can be adjusted to low or high with [▲] [▼]. With [P] the selection is
confirmed and the display changes back into menu level. This is a very important setting, as it
is used for all operation types type!
Setting the code for the adjustment lock, s.code:
Default: 0000
The code for the adjustment lock is adjusted from the smallest to the highest digit with [▲] [▼]
and confirmed digit per digit with [P]. After the last digit the display changes back into menu
level. If the s.code is set on a value unequal 0000, the code lock is activated for type, F.tast and
f.inpu. This means at each adjustment attempt the releasing code s.code is recalled. For typesettings E.tast the enable code s.code has no meaning.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–INP-“.
13
5. Setting up the device
5.4.2. General device parameters
Menu group level
Menu level
Menu level
Parameterisation level
Display flashing, FLASH:
Default: no
A display flashing can be added as additional alarm function either to single or to a combination
of off-limit condition. With no, no flashing is allocated.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „– fct –“.
5.4.3. Safety parameters
Menu group level
Menu level
Menu level
Parameterisation level
User code U.Code:
Default: o000
Via this code reduced sets of parameters can be released. A change of the U.CodE can only be
done via the correct input of the A.CodE (master code).
Master code, A.Code:
Default: 1234
By entering A.CodE the device will be unlocked and all parameters are released.
14
5. Setting up the device
Menu level
Parameterisation level
Release/lock analog output parameters, Out.LE:
Default: all
Analog output parameter can be locked or released for the user:
- At En-oF the initial or final value can be changed in operation mode.
- At Out.EO the output signal can be changed from e.g. 0-20 mA to 4-20 mA or 0-10 VDC.
- At ALL analog output parameters are released.
- At no all analog output parameters are locked.
Release/lock alarm parameters, AL.LEU:
Default: all
This parameter describes the user relase/user lock of the alarm.
- LIMIt, here only the range of value of the threshold values 1-4 can be changed.
- ALrM.L, here the range of value and the alarm trigger can be changed.
- ALL, all alarm parameters are released.
- no, all alarm parameters are locked.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „– COD –“ .
15
5. Setting up the device
5.4.4. Analog output parameters
Menu group level
Menu level
Menu level
Parameterisation level
Selection analog output, Out.rA:
Default: 0-10
Two output signals are available, 0-10 VDC and 0-20 mA, they can be selected with [▲] [▼]
and confirmed with [P]. A limitation of the output range can be done via Out.en and Out.OF to e.g.
4-20 mA.
Setting up the output-final value, Out.En:
Default: 10.000
The output-final value is adjusted from the smallest to the highest digit with [▲] [▼] and
confirmed digit per digit with [P]. After the last digit the display changes back into menu level.
Depending on the adjusted output signal Out.rA the value corresponds to a voltage of 0…10 V
or a current of 0…20 mA and is reached, when the adjustment-final value END is reached as
setpoint.
Setting up the analog output-initial value, Out.OF:
Default: 00.000
The analog output-initial value is adjusted from the smallest to the highest digit with [▲] [▼]
and confirmed digit per digit with [P]. After the last digit the display changes back into menu
level. Depending on the adjusted output signal Out.rA the value corresponds to a voltage of
0…10 V or a current of 0…20 mA and is reached, when the adjustment-initial value OFFS is
reached as setpoint.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „– out –“.
16
5. Setting up the device
5.4.5. Relay functions
Menu group level
Menu level
Menu level
Parameterisation level
Alarm relay 1, rEL-1:
Default: off
….
….
Each setpoint (optional) can be linked up via 4 alarms (by default). This can either be inserted
at activated alarms AL1/4 or deactivated alarms ALN1/4. If LOGIC is selected, logical links are
available in the menu level LoG-1 and CoM-1. One can only get to these two menu levels via LOGIC,
at all other selected functions, these two parameters are overleaped. Via On/OFF the setpoints
can be activated/de-activated, in this case the output and the setpoint display are set/not set on
the front of the device. With [P] the selection is confirmed and the device changes into menu
level.
Logic relay 1, Log-1
Default: or
Here, the switching behavior of the relay is defined via a logic link, the following schema
describes these functions with inclusion of AL-1 and AL-2:
A1 v A2
As soon as a selected alarm is activated, the relay
operates. Equates to operating current principle.
A1 v A2 = A1 Λ A2
The relay operates only, if no selected alarm is
active. Equates to quiescent current principle.
A1 Λ a2
The relay operates only, if all selected alarms are
active.
A1 Λ A2 = A1 v A2
As soon as a selected alarm is not activated, the
relay operates.
____ _ _
____ _ _
With [P] the selection is confirmed and the device changes into menu level.
Alarms for relay 1, CoM-1:
Default: a.1
….
The allocation of the alarms to relay 1 happens via this parameter, one alarm or a group of
alarms can be chosen. With [P] the selection is confirmed and the devices changes into menu
level.
17
5. Setting up the device
Menu level
Parameterisation level
Alarm relay 2, reL-2:
Default: off
….
….
Each setpoint (optional) can be linked up via 4 alarms (by default). This can either be inserted
at activated alarms AL1/4 or deactivated alarms ALN1/4. If LOGIC is selected, logical links are
available in the menu level LoG-1 and CoM-1. One can only get to these two menu levels via LOGIC,
at all other selected functions, these two parameters are overleaped. Via On/OFF the setpoints
can be activated/de-activated, in this case the output and the setpoint display are set/not set on
the front of the device. With [P] the selection is confirmed and the device changes into menu
level.
Logic relay 2, LoG-2:
Default: or
Here, the switching behavior of the relay is defined via a logic link, the following schema
describes these functions with inclusion of AL-1 and AL-2:
A1 v A2
As soon as a selected alarm is activated, the relay
operates. Equates to operating current principle.
A1 v A2 = A1 Λ A2
The relay operates only, if no selected alarm is
active. Equates to quiescent current principle.
A1 Λ a2
The relay operates only, if all selected alarms are
active.
A1 Λ A2 = A1 v A2
As soon as a selected alarm is not activated, the
relay operates.
____ _ _
____ _ _
With [P] the selection is confirmed and the device changes into menu level.
Alarms for relay 2, CoM-2:
Default: a. 2
….
The allocation of the alarms to relay 2 happens via this parameter, one alarm or a group of
alarms can be chosen. With [P] the selection is confirmed and the devices changes into menu
level.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „– rel –“.
18
5. Setting up the device
5.4.6. Alarm parameters
Menu group level
Menu level
Menu level
Parameterisation level
Threshold values / limit values, LI-1:
Default: 2000
For both limit values, two different values can be parameterized. With this, the parameters for
each limit value are called up one after another.
Hysteresis for limit values, HY-1:
Default: o0000
A hysteresis function exists for all limit values, that reacts according to the settings (threshold
exceedance / threshold undercut).
Function if display falls below / exceeds limit value, FU-1:
Default: high
The limit value undercut can be selected with Louu (LOW = lower limit value) and limit value
exceedance can be selected with high (HIGH = upper limit value). If e.g. limit value 1 is on a
switching threshold of 100 and occupied with function high, the alarm will be activated when
reaching the threshold. If the limit value is allocated to Low, an alarm will be activated by
undercut of the threshold.
Switching-on delay, ton-1:
Default: 000
For limit value 1 one can preset a delayed switching-on of 0-100 seconds.
19
6. Reset to default values
Menu level
Parameterisation level
Switching-off delay, toF-1:
Default: 000
For limit value 1 one can preset a delayed switching-off of 0-100 seconds.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „– Ali –“ .
The same applies to –Al2– to –Al4–.
Programming interlock:
Description see page 11, menu-level run
Menu-group level
6. Reset to factoty settings
To return the unit to a defined basic state, a reset can be carried out to the default values.
The following procedure should be used:
• Switch off the power supply
• Press button [P]
• Switch on voltage supply and press [P]-button until „- - - - -“ is shown in the display.
With reset, the default values of the program table are loaded and used for subsequent operation. This sets
the unit back to the state in which it was supplied.
Caution! All application-related data are lost.
20
7. Alarms / Relais
7. Alarms / Relays
This device has 4 virtual alarms that can monitor one limit value in regard of an undercut or
exceedance. Each alarm can be allocated to an optional relay output S1-S2.
Function principle of alarms / relays
Alarm / Relay x
Deactivated, instantaneous value, min/max-value, Hold-value, totaliser
value
Switching threshold
Threshold / limit value of the change-over
Hysteresis
Broadness of the window between the switching thresholds
Working principle
Operating strom / Quiescent current
Operating current
By operating current the alarm S1-S4 is off below
the threshold and on on reaching the threshold.
Quiescent current
By quiescent current the alarm S1-S4 is on
below the threshold and switched off on reaching
the threshold.
Switching-on delay
The switching-on delay is activated via an alarm
and e.g. switched 10 seconds after reaching the
switching threshold, a short-term exceedance of
the switching value does not cause an alarm,
respectively does not cause a switching
operation of the relay. The switching-off delay
operates in the same way, keeps the alarm / the
relay switched longer for the parametrised time.
21
8. Technical data
8. Technical data
Housing
Sizes
96x48x70 mm (BxHxD)
96x48x89 mm (BxHxD) incl. plug-in terminal
Panel cut-out
92.0+0.8 x 45.0+0.6 mm
Wall thickness
up to 15 mm
Fixing
screw elements
Material
PC polycarbonate, black, UL94V-0
Sealing material
EPDM, 65 Shore, black
Protection class
standard IP65 (front), IP00 (back side)
Weight
approx. 200 g
Connection
plug-in terminal; wire cross section up to 2.5 mm2
Display
Digit height
14 mm
Segment colour
red (optional green, yellow or blue)
Range of display
-19999 to 99999
Setpoints
one LED per setpoint
Overflow
horizontal bars at the top
Underflow
horizontal bars at the bottom
Input
Transmitter
2 digital inputs
HTL level
TTL level
< 2.4 V OFF; > 10 V ON, max. 30 VDC
< 1.9 V OFF, > 4.6 V ON
Input resistance
RI ~ 5 kΩ
Output
Contact supply
15 VDC / 10 mA
Analog output
0/4-20 mA / burden ≤ 500Ω;
0-10 VDC / burden ≥ 10 kΩ,
16 Bit
Switching output
Relay with change-over
contacts Switching cycles
250 VAC / 5 AAC; 30 VDC / 5 ADC
30 x 103 at 5 AAC, 5 ADC ohm resistive load
10 x 106 mechanically
Diversity according to DIN EN50178
/ Characteristics according to DIN EN60255
Power pack
230 VAC +/- 10 % max. 10 VA
10-30 VDC galv. insulated, max. 4 VA
22
8. Technical data
Memory
EEPROM
Data life
≥ 100 years at 25°C
Ambient conditions
Working temperature
0…50°C
Storing temperature
-20…80°C
Climatic density
relative humidity 0-80% on years average without dew
EMV
EN 61326
CE-sign
Conformity to directive 2004/108/EG
Safety standard
EN 61010; EN 60664-1
23
9. Safety advices
9. Safety advices
Please read the following safety advice and the assembly chapter 1 before installation and keep it for
future reference.
Proper use
The M2-1G-device is designed for the evaluation and display of sensor signals.
Attention! Careless use or improper operation can result in
personal injury and/or cause damage to the equipment.
Control of the device
The panel meters are checked before dispatch and sent out in perfect condition. Should there be any
visible damage, we recommend close examination of the packaging. Please inform the supplier
immediately of any damage.
Installation
The M2-1G-device must be installed by a suitably qualified specialist (e.g. with a qualification in
industrial electronics).
Notes on installation
• There must be no magnetic or electric fields in the vicinity of the device, e.g. due to transformers,
mobile phones or electrostatic discharge.
• The fuse rating of the supply voltage should not exceed a value of 6A N.B. fuse.
• Do not install inductive consumers (relays, solenoid valves etc.) near the device and suppress
any interference with the aid of RC spark extinguishing combinations or free-wheeling diodes.
• Keep input, output and supply lines separate from one another and do not lay them parallel with
each other. Position “go” and “return lines” next to one another. Where possible use twisted pair.
This way, best measuring results can be received.
• Screen off and twist sensor lines. Do not lay current-carrying lines in the vicinity. Connect the
screening on one side on a suitable potential equaliser (normally signal ground).
• The device is not suitable for installation in areas with a risk of explosion.
• Any electrical connection deviating from the connection diagram can endanger human life and/or
can destroy the equipment.
• The terminal area of the device is part of the service. Here, electrostatic discharge needs to be
avoided. Attention! High voltages can cause dangerous body currents.
• Galvanic isolated potentials within one complex need to be placed on an appropriate point (normally
earth or machines ground). So, a lower disturbance sensibility against impacted energy can be
reached and dangerous potentials, that can occur on long lines or due to faulty wiring, can be
avoided.
24
10. Error elimination
10. Error elimination
1.
Error description
Measures
The device shows –LOC– at the attempt
of change.
• The adjustment lock for the setpoint is active,
please check if there is a key-switch.
• The active input signal In.lev has to be adjusted
to HIGH instead of LOW or vice versa.
-LOC2.
By the code recall for the setpoint
appears FAIL or there is an unexpected
code-recall.
CodE
FAIL
• At an unexpected code recall, S.CodE needs to
be set on a value unequal 0000. Check the
parametrisation and set back the parameter.
• If FAIL appears after entering the code, check
the S.CodE in the parameterisation.
3.
The word "HELP " lights up in the
7-segment display.
• The unit has found an error in the configuration
memory. Perform a reset on the default values
and re-configure the unit according to your
application.
4.
The display does not change back to
parametrisation after pressing [P].
• Programming lock is activated
• Enter correct code
5.
"Err1" lights up in the 7-segment
display
• Please contact the manufacturer if errors of this
kind occur.
6.
The device does not react as
expected.
• If you are not sure if the device has been
parameterised before, then follow the steps as
written in chapter 6 and set it back to its
delivery status.
25
M2_1GGB.pdf
update: 28.03.2014
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement