MultiBio700 User Manual
MultiBio700 User Manual
Version: 1.0
Date: Oct. 2010
About This Manual
This document introduces the user interface and menu operations of MultiBio700.
For the installation please refer to Installation Guide.
Table of Contents
TABLE OF CONTENTS
1. INSTRUCTION FOR USE ............................................................................... 1
1.1 STANDING POSITION, POSTURE AND FACE EXPRESSION ................................. 1
1.2 ENROLLMENT FACE EXPRESSION .................................................................... 2
1.3 FINGER PLACEMENT........................................................................................ 3
1.4 USE OF TOUCH SCREEN ................................................................................... 4
1.5 TOUCH OPERATIONS ........................................................................................ 5
1.6 APPEARANCE OF DEVICE ................................................................................. 7
1.7 MAIN INTERFACE ............................................................................................ 8
1.8 VERIFICATION MODES ................................................................................... 10
1.8.1 Fingerprint Verification ...................................................................... 10
1.8.2 Face Verification ................................................................................ 12
1.8.3 Password Verification ....................................................................... 13
1.8.4 ID Card Verification ★ ..................................................................... 14
1.8.5 Combination Verification ★ ............................................................ 15
2. MAIN MENU .................................................................................................... 17
3. ADD USER....................................................................................................... 19
3.1 ENTERING A USER ID .................................................................................... 20
3.2 ENTERING A NAME ........................................................................................ 21
3. 3 ENROLLING A FINGERPRINT .......................................................................... 22
3. 4 ENROLLING A PASSWORD ............................................................................. 24
3. 5 ENROLLING A FACE ...................................................................................... 25
3.6 ENTERING A GROUP NO. ................................................................................ 26
3.7 MODIFY USER RIGHTS .................................................................................. 28
3.8 ENROLL PHOTOS ........................................................................................... 29
3.9 USER ACCESS SETTING ................................................................................. 30
I
MultiBio700 User Manual 1.0
3.10 ENROLLING AN ID CARD ★ ....................................................................... 33
4. USER MANAGEMENT .................................................................................. 34
4.1 EDIT A USER .................................................................................................. 35
4.2 DELETE A USER ............................................................................................. 36
4.3 QUERY A USER .............................................................................................. 37
5. COMMUNICATION SETTINGS .................................................................... 38
5.1 NETWORK SETTINGS ..................................................................................... 39
5.2 WIEGAND OUTPUT ........................................................................................ 41
5.2.1 Wiegand 26-bits Output Description ............................................... 42
5.2.2 Wiegand 34-bits Output Description ............................................... 44
5.2.3 Customized Format ........................................................................... 46
5.3 WIEGAND INPUT ........................................................................................... 50
6. SYSTEM CONFIGURATION ........................................................................ 51
6.1 GENERAL PARAMETERS ................................................................................ 52
6.2 INTERFACE PARAMETERS .............................................................................. 53
6.3 FINGERPRINT PARAMETERS ........................................................................... 54
6.4 FACE PARAMETERS........................................................................................ 56
6.5 LOG SETTINGS .............................................................................................. 58
6.6 KEYBOARD DEFINITIONS .............................................................................. 59
6.7 ACCESS SETTING ........................................................................................... 60
6.7.1 Time zone setting .............................................................................. 61
6.7.2 Holiday setting ................................................................................... 62
6.7.3 Group time zone setting ................................................................... 64
6.7.4 Unlock Combination Setting ............................................................ 67
6.7.5 Access control parameter................................................................. 69
6.7.6 Duress alarm parameter ................................................................... 71
II
Table of Contents
6.7.7 Anti-Pass back setting ...................................................................... 72
6.8 UPDATE ......................................................................................................... 73
7. DATA MANAGEMENT ................................................................................... 74
8. DATE/TIME SETTING ................................................................................... 77
8.1 SET DATE/TIME ............................................................................................ 77
8.2 BELL SETTING ★ ......................................................................................... 78
9. AUTO TEST ..................................................................................................... 80
10. USB DISK MANAGEMENT ........................................................................ 82
11. SYSTEM INFORMATION ........................................................................... 83
12. APPENDIX..................................................................................................... 84
APPENDIX 1 T9 INPUT INSTRUCTIONS ................................................................. 84
APPENDIX 2 INTRODUCTION OF WIEGAND .......................................................... 86
APPENDIX 3 PHOTO ID FUNCTION ...................................................................... 88
APPENDIX 4 MULTI-COMBINATION AUTHENTICATION MODE ★ ........................ 89
APPENDIX 5 ANTI-PASS BACK ★ ....................................................................... 93
APPENDIX 6 STATEMENT ON HUMAN RIGHTS AND PRIVACY ............................... 96
APPENDIX 7 ENVIRONMENT-FRIENDLY USE DESCRIPTION .................................. 98
1. Instruction for Use
1. Instruction for Use
1.1 Standing Position, Posture and Face Expression
1. Recommended standing-distance from device:
For users 5-6 feet tall (1.5m-1.85m) we recommend users
stand about 2 feet (0.5m) from the wall.
When viewing your image on the device display window,
step away if your image appears too bright. Step closer if
your image appears too dark.
2. Recommended face Expressions vs. poor Expressions:
3. Recommended Posture (pose) vs. poor Posture (pose):
"
Note: During enrollment and verification, try to have a relaxed unstrained face
expression and stand upright.
1
MultiBio700 User Manual 1.0
1.2 Enrollment Face Expression
During the enrollment, position your head such that your face appears in the center
of the device display window. The device will prompt you how to move your head.
Follow the voice prompts by first gently turning your head left, then right. Then your
head gently down, then up , and so on. There slight variations of head angles will
help the device better recognize your face when you attempt verifying:
The enrollment face experssion as follows:
Look ahead
Look at screen
Bow down
Turn left
Turn right
2
1. Instruction for Use
1.3 Finger Placement
Recommended fingers: The index finger, middle finger or the ring finger; the thumb
and little finger are not recommended (because they are usually clumsy on the
fingerprint collection screen).
1. Proper finger placement:
The finger is flat to the surface
and centered in fingered guide.
2. Improper finger placement:
Not flat to the surface
Slanting
Off-center
Off-center
Please enroll and verify your fingerprint by using the proper finger
placement mode. We shall not be held accountable for any consequences
arising out of the degradation in verification performance due to improper
user operations. We shall reserve the right of final interpretation and
revision of this document.
3
MultiBio700 User Manual 1.0
1.4 Use of Touch Screen
Touch the screen with one of your fingertips or the top of the forward edge of a
fingernail, as shown in the following figure. A broad point of contact may lead to
inaccurate pointing.
When the touch screen is less sensitive to the touch, you can perform screen
calibration through menu operations. Press [Menu] -> [Auto Test] -> [Calibration]
on the screen and a cross icon will be displayed. After you touch the center of the
cross at five locations on the screen correctly, the system automatically returns to
the main menu. Press [Exit] to return to the initial interface. For details, see the
description in 9. Auto Test.
Smear or dust on the touch screen may affect the performance of the touch screen.
Therefore, try to keep the screen clean and dust-free.
4
1. Instruction for Use
1.5 Touch Operations
1. Enter numbers: Press the
[User ID] key. The system
automatically
displays
the
number input interface. After
entering the user ID, press [OK]
to save or press [X] to cancel
and return to the previous
interface.
2. Enter Text: Press the [Name]
key. The system automatically
displays the text input interface.
After entering the user name,
press [X] to save and return to
the previous interface.
5
MultiBio700 User Manual 1.0
3. Modify parameters: Press
the default value of a parameter
and the system automatically
switches to another value of this
parameter.
6
1. Instruction for Use
1.6 Appearance of Device
1.Front View
Indicator
Touch Screen
Touch keys
Camera
Push Buttons
Fingerprint Sensor
2.Side View
ID Card Swipe Area
Reset Button
USB Port
7
MultiBio700 User Manual 1.0
1.7 Main Interface
™ Date
™ Screen Shortcut
™ Time
™ Attendance Status
™ Face Image
™ 1:1 Switch Key
™ Menu
1:1
™ 1:1 Switch button
™ Door Bell
① Date: Current date is displayed.
② Screen Shortcut Keys: Press this shortcut keys to display the attendance status
and enter the functional interface quickly. Users can customize the function of each
shortcut key. For details, see 6.6 Keyboard Definitions.
③ Time: Current time is displayed. Both the 12-hour and 24-hour time systems are
supported.
④ Attendance Status: Current attendance status is displayed.
⑤ Fingerprint Image: When the fingerprint image is displayed, the device is
8
1. Instruction for Use
currently in the fingerprint recognition mode.
⑥ 1:1 Switch Key: By pressing this key, you can switch to the 1:1 verification
modes, and enter the digital input interface. The function is same to ⑨[1:1] Switch
Button.
⑦ Menu: You can enter the main menu by touching this key.
⑧ Door Bell: For guest to ring the bell and ask for opening the door.
⑨ 1:1 Switch Button: You can enter the digital input interface of 1:1 verification
mode.
9
1. Instruction for Use
1.8 Verification Modes
1.8.1 Fingerprint Verification
1. 1:N fingerprint verification
In the fingerprint verification mode, the device compares
current fingerprint collected by the fingerprint collector with
all fingerprint data on the device.
1. The default main interface is the fingerprint verification
mode, see the figure on the right.
2. Press your finger on the fingerprint collector by adopting
the proper finger placement. For details, see 1.3 Finger
Placement.
3. If the verification is successful, the device prompt
“Verified”.
4. If the verification is not successful, the device prompt “Please try again”.
10
1. Instruction for Use
2. 1:1 fingerprint verification
In the 1:1 fingerprint verification mode, the device
compares current fingerprint collected through the
fingerprint collector with that in relation to the user ID
entered through keyboard. Adopt this mode only when it
is difficult to recognize the fingerprint.
1. Press [1:1] on the screen or [1:1] keyboard to enter the
1:1 fingerprint recognition mode.
2. Enter user ID and then press the "Fingerprint” icon to
enter 1:1 fingerprint recognition mode. If the prompt
“Unregistered user!” is displayed, the user ID is not exist.
3. Press your finger on the fingerprint collector by
adopting the proper finger placement. For details, see 1.3 Finger Placement.
4. If the verification is successful, , the device prompt “Verified”, otherwise the device
prompt “Please try again”.
11
MultiBio700 User Manual 1.0
1.8.2 Face Verification
1:1 face verification
In the 1:1 face verification mode, the device compares
current face collected through the camera with that in
relation to the user ID entered through keyboard. Adopt this
mode only when it is difficult to recognize the face.
1. Press [1:1] on the screen or [1:1] keyboard to enter the
1:1 recognition mode.
2. Enter user ID and then press the "1:1 Face” icon to enter
1:1 face recognition mode. If the prompt “Unregistered
user!” is displayed, the user ID is not exist.
3. Compare the face in a proper way. For details, see 1.1
Standing Position, Posture and Face Expression.
4. If the verification is successful, the device prompt “Verified”. The system will return
to the main interface if the verification is not passed within 20 seconds.
12
1. Instruction for Use
1.8.3 Password Verification
In the password verification mode, the device compares
the password entered with that in relation to the user ID.
1. Press [1:1] on the screen or [1:1] keyboard to enter the
password verification mode.
2. Enter the user ID and then press the "Key” icon to enter
password verification mode. If the prompt “Unregistered
user!” is displayed, the user ID is not exist.
3. Enter the password and press the “OK” icon to start the
password comparison.
4. If the verification is successful, the device prompt
“Verified”, otherwise the device prompt “Verify fail” and
return to password input interface.
13
MultiBio700 User Manual 1.0
1.8.4 ID Card Verification ★
" Note: Only the products with a built-in ID card module
support the ID card verification.
In the fingerprint verification mode, the device compares
current ID Card collected by the Card Reader with all ID
Card data on the device.
1. Swipe your ID Card on the Card Swipe Area by adopting
the proper way. For the Card Swipe Area, see 1.6
Appearance of Device.
3. If the verification is successful, the device prompt
“Verified”.
4. If the verification is not successful, the device prompt “Card not Registered”.
14
1. Instruction for Use
1.8.5 Combination Verification ★
The device support 20 verification modes, including FACE&PIN/FP/RF/PW 、
FP&PW、FP&RF、FACE&FP、FACE&PW、FACE&RF、FP、PW、RF、FACE&PIN、
FP/RF 、 PW/RF 、 FP/PW 、 PW&RF 、 PIN&FP 、 FP&PW&RF 、 PIN&FP&PW 、
FP&RF/PIN、FACE&FP&RF、FACE&FP&PW etc. For the detail, please refer to
Appendix 4 Multi-combination Authentication Mode.
" Note: RF means ID Card verification. Only the products with a built-in ID card
module support the ID card verification.
Here is the combination verification operation, we use the FACE&FP verification for
an example.
If you verify fingerprint first and then the face verify, operation as follows.
(1) The default main interface is the fingerprint verification mode, see the figure
below.
(2) Press your finger on the fingerprint collector by adopting the proper finger
placement. For details, see 1.3 Finger Placement.
(3) If the verification is successful, the device enter the 1:1 face recognition mode.
15
MultiBio700 User Manual 1.0
Compare the face in a proper way. For details, see 1.1 Standing Position, Posture and
Face Expression.
(4) If the verification is successful, the device prompt “Verified”. The system will
return to the main interface if the verification is not passed within 20 seconds.
Otherwise,
the
FACE&FP combination
verification
can
perform
such
as
FACE(1:N)+FP, PIN+FACE(1:1)+FP, PIN+FP(1:1)+FACE etc. The operation is
similar to the procedure introduced before.
16
2. Main Menu
2. Main Menu
There are two types of rights respectively granted to two types of users: the
Ordinary users and administrators. Ordinary users are only granted the rights of
face, fingerprint, password or card verification, while administrators are granted the
access to the main menu for various operations apart from having all the privileges
granted to ordinary users.
Press [Menu] on the initial interface to access the main menu, as shown in the
following figure:
The main menu includes nine submenus:
Add User: Through this submenu, you can add a new user and input the information
on the device, including the user ID, name, fingerprint, face, card, password, rights,
group No. and user access.
User Mgt.: Through this submenu, you can browse the user information stored on
the device, including the user ID, name, fingerprint, face, card, password, rights,
group No. and user access. And add, modify or delete the user information.
17
2 Main Menu
Comm.: Through this submenu, you can set related parameters for communication
between the device and PC, including the IP address, gateway, subnet mask, baud
rate, device No. and communication password.
System: Through this submenu, you can set system-related parameters, including
the basic parameters, interface parameters, fingerprint, face and attendance
parameters, Keyboard definitions, Access setting, firmware update etc. to enable the
device to meet user requirements to the greatest extent in terms of functions and
display.
Data Mgt.: Through this submenu, you can perform management of data stored on
the device, for example, deleting the attendance record, all data, clear administrator,
restore to factory settings and query records.
Date/Time: Through this submenu, you can set the alarm time and duration, or set
the Bell.
Auto Test: This submenu enables the system to automatically test whether
functions of various modules are normal, including the screen, collector, voice, face,
keyboard, clock tests and screen calibration.
Dn/Upload: Through this submenu, you can import user information and attendance
data stored in the device through a USB disk to related software or other fingerprint
recognition equipment.
Sys Info.: Through this submenu, you can browse the records and device
information.
Any user can access the main menu by pressing the [Menu] key if the
system is free from administrators. After administrators are configured
on the device, the device needs to verify the administrators’ identity
before granting them access to the main menu. To ensure device
security, it is recommended to set an administrator when using the
terminal initially. For detailed operations, see 3.7 Modify User Rights .
18
3. Add User
3. Add User
Press [Add] on the [User Mgt.] interface to display the [Add
User] interface as shown below.
User ID: Enter a user ID. 1 to 9 digits user IDs are
supported by default.
Name: Enter a user name. 12 characters user names are
supported by default.
Fingerprint: Enroll a user’s fingerprint and the Device
displays the number of enrolled fingerprints. A user can
enroll 10 fingerprints at maximum.
Password: Enroll a user’s password. 1 to 8 digits passwords
are supported by default.
Face: Enroll a user’s face.
Group No.: Set the group that the user belongs to. Valid
group No.: 1–24.
Role: Set the rights of a user. A user is set to ordinary
user by default and can also be set to administrator.
Ordinary users are only granted the rights of face,
fingerprint or password verification, while administrators
are granted the access to the main menu for various
operations apart from having all the privileges granted to
ordinary users.
Photo: Enroll a user’s photo. During user verification, the
user’s photo is displayed on screen.
User Access: Set the lock control and access control parameters.
19
MultiBio700 User Manual 1.0
3.1 Entering a User ID
The device automatically allocates an ID starting from 1 for
every user in sequence. If you use the ID allocated by the
device, you may skip this section.
1. Press [User ID] on the [Add User] interface to display
the user ID management interface.
" Tip: The user ID can be modified during initial
enrollment, but once enrolled, it cannot be modified.
2. On the displayed keyboard interface, enter a user ID
and press [OK]. If a prompt message “The user ID already
exists!” is displayed, enter another ID.
" Tip: The device supports 1 to 9 digits user IDs by
default. If you need to extend the length of current
user ID numbers, please consult our commercial
representatives
or
fore-sale
technical
support
personnel.
3. After the user ID is entered, press [Save] to save current
information and return to the previous interface. Press
[Exit] to return to the previous interface without saving
current information.
20
3. Add User
3.2 Entering a Name
Use T9 input method to enter the user name through the
keyboard.
1. Press [Name] on the [Add User] interface to display the
name input interface.
2. On the displayed keyboard interface, enter a user
name and press [X].
For details of operations on keyboard interface, see
Appendix 1 T9 Input Instructions.
3. After the user name is entered, press [Save] to save
current information and return to the previous interface.
Press [Exit] to return to the previous interface without
saving current information.
" Tip: The device supports the 1 to 12 characters names by default.
21
MultiBio700 User Manual 1.0
3. 3 Enrolling a Fingerprint
1. Press [Fingerprint] on the [Add User] interface to
display the [Enroll Fingerprint] interface.
2. On the displayed [Enroll Fingerprint] interface, place
your finger on the fingerprint collector properly
according to the system prompt. For details, see 1.3
Finger Placement.
3. Place the same finger on the fingerprint collector for
three consecutive times correctly. If the enrollment
succeeds, the system will display a prompt message
and automatically return to the [Add User] interface. If
the enrollment fails, the system will display a prompt
message and return to the [Enroll Fingerprint] interface. In this case, you need to
repeat the operations of step 2.
4. You can back up the enrolled fingerprint of a user by pressing [Fingerprint]. A user
can enroll 10 fingerprints at maximum.
5. Press [Save] to save current information and return to the previous interface.
Press [Exit] to return to the previous interface without saving current information.
22
3. Add User
23
MultiBio700 User Manual 1.0
3. 4 Enrolling a Password
1. Press [Password] on the [Add User] interface to display
the password management interface.
2. On the displayed keyboard interface, enter a password
and press [OK]. Re-enter the password according to the
system prompt and then press [OK].
"
Tip: The device supports the 1 to 8 digits
passwords by default.
3. After the password is entered, an interface is displayed
as shown below. Press [Save] to save current information
and return to the previous interface. Press [Exit] to return to
the previous interface without saving current information.
24
3. Add User
3. 5 Enrolling a Face
1. Press [Face] on the [Add User] interface to display the
face enrollment interface.
2. On the displayed face enrollment interface, turn your
head to the left and right slightly, raise and lower your
head according to the voice prompts, so as to enroll
different parts of your face into the system to assure
accurate
verification.
See
1.2
Enrollment
Face
Expression.
3. If your face image is enrolled successfully, the system
will display a prompt message and automatically return to
the [Add User] interface.
4. Press [Save] to save current information and return to the previous interface.
Press [Exit] to return to the previous interface without saving current information.
25
MultiBio700 User Manual 1.0
3.6 Entering a Group No.
During
face
enrollment,
the
device
automatically
allocates a group No. starting from 1 for every user in
sequence. When the number of users in Group No.1
reaches the upper limit, the rest users fall under Group
No.2 automatically. Up to 100 face images can be
enrolled in Group No.1 and only 50 face images can be
enrolled in other groups. If you use the group No.
allocated by the device, you may skip this section.
1. Press [Group No.] on the [Add User] interface to
display the group No. management interface.
2. On the displayed keyboard interface, enter your group
No. and press [OK].
3. After the group No. is entered, an interface is displayed as shown below. Press
[Save] to save current information and return to the previous interface. Press [Exit] to
return to the previous interface without saving current information.
" Tip: A valid group No. contains 1–24 digits. Please remember your own group
No.
26
3. Add User
27
MultiBio700 User Manual 1.0
3.7 Modify User Rights
" Note: There are two types of rights respectively granted to two types of users:
the ordinary users and administrators. Ordinary users are only granted the rights
of face, fingerprint, or password verification, while administrators are granted the
access to the main menu for various operations apart from having all the privileges
granted to ordinary users.
1. On the [Add User] interface, press [Role: User] to change the user into an
administrator.
2. After the modification is done, the interface is as shown below. Press [Save] to
save current information and return to previous interface; press [Exit] to directly
return to previous interface without saving current information.
28
3. Add User
3.8 Enroll Photos
If you have enrolled your photo in the system, the
system will display your enrolled photo in addition to
your ID and name after you pass the verification.
1. Press [Photo] on the [Add User] interface to display
the photo enrollment interface.
2. On the photo enrollment interface, stand naturally in
front of the screen. For details, see 1.1 Standing
Position, Posture and Face Expression. Press [Capture]
to capture the photo.
3. After taking the photo, press [Exit] to return to
previous interface.
4. After the photo is taken, press [Save] to save current information and return to
previous interface; press [Exit] to directly return to previous interface without saving
current information.
29
MultiBio700 User Manual 1.0
3.9 User Access Setting
Press [User Access] on the
[Add User] interface to display
the
user
access
setting
interface.
User Access setting is to set the
user right to verify and open the
door. Including Verify Type,
Time Zone and Duress FP
management.
1. Verify Type:
(1) Group Verify Mode: If the
user use the group verify mode
that he belong to.
(2) Individual verify mode:
Select the verify mode for this
user instead of the group verify
mode. That will not effect the
other user in the group.
" Note:
(1) Only the products with a built-in ID card module support the ID card verification.
(2) For the verify type, please refer to Appendix 4 Multi-combination Authentication
Mode. Only some type of device support Multi-combination authentication mode.
30
3. Add User
2. Time Zone:
(1) Group Time Zone: If the user use the group time zone that he belong to.
(2) Individual time zone: Select the time zone of this user instead of the group time
zone. That will not effect the other user in the group.
3. Duress FP:
Enroll a new duress fingerprint or cancel an exist one. In
any situation, only if the enrolled duress fingerprint is
verified, it will trigger the duress alarm.
Duress FP management:
(1) Register Duress FP:
Press [Reg. Duress FP] on the [User Access] interface to
display the [Enroll Fingerprint] interface. On the displayed
[Enroll Fingerprint] interface, place your finger on the
fingerprint collector properly according to the system
prompt. For details, see 1.3 Finger Placement.
31
MultiBio700 User Manual 1.0
(2) Cancel duress FP:
Press [Can.Duress FP] on the [User Access] interface to popup the confirm
message. Select [YES] to delete the enrolled duress FP, otherwise select [NO] to
cancel the operation.
32
3. Add User
3.10 Enrolling an ID Card ★
1. Press [Card] on the [Add User] interface to display the
[Enroll Card] interface.
2. The [Punch Card!] interface pops out as shown below.
Swipe your ID card properly in the swiping area. For
details, see 1.6 Appearance of the Device.
3. If the card passes the verification, the Device displays
a prompt message “Read Successfully! Card No.:
**********”, and returns to the [Add User] interface.
4. Press [Save] to save current information and return to
the previous interface. Press [Exit] to return to the
previous interface without saving current information.
33
4. User Management
4. User Management
Browse the user information, including the user ID,
name, fingerprint, face, ID card, password, rights, group
No. and user access settings. To add, edit or delete the
basic information of users.
Press [User Management] on the main menu interface
to display the user management interface.
The user is an administrator.
" Note: The users are listed in alphabetical order by last name. If you select a
user, you can access the editing interface of this user to edit or delete related user
information.
34
4. User Management
4.1 Edit a User
Select a user from the list to enter [User Info] interface.
The User ID cannot be modified, and the other operations are similar to those
performed to add a user. You can re-enroll your fingerprint and face image, change
your password and modify the management rights and group No.
For example: Change the user right from Administrator to ordinary user. As the
figure shown below.
35
MultiBio700 User Manual 1.0
4.2 Delete a User
On the [User Info] interface, you can delete all or partial user information.
1. Press [Delete] to delete a user.
2. On the interface displayed, click [YES] to delete current user and [NO] to return to
previous interface.
3. On the [User Info] interface, press [Name], [Fingerprint], [Face] or [Password] to
delete related user information and re-enroll the new information follow the device
prompt.
36
4. User Management
4.3 Query a User
To facilitate administrators to locate a user quickly from
a large number of enrolled users, the Device enables
user query by his/her “User ID”.
User ID Query:
1. Press [Query] on the [User Management] interface to
display the User ID query interface.
2. Enter the user ID on the displayed interface, and click
[OK] to locate the cursor to the desired user.
37
5. Communication Settings
5. Communication Settings
You can set related parameters for the communication between the Device and PC,
including the IP address, gateway, subnet mask, baud rate, equipment ID, and
communication password.
38
5. Communication Settings
5.1 Network Settings
When the Device communicates with the PC over Ethernet, you need to check the
following settings:
IP Address: The IP address is 192.168.1.201 by default and can be changed as
required; the IP address of the Device and that of the PC cannot be duplicated.
Subnet Mask: The subnet mask is 255.255.255.0 by default and can be changed as
required.
Gateway: The gateway is 0.0.0.0 by default. If the Device and the PC are not
located in the same network segment, you need to set the gateway.
When the Device communicates with the PC over serial ports (RS232/RS485), you
need to check the following settings:
RS232: This parameter is used to enable or disable the RS232 communication. If
the RS232 communication cables are used, set this parameter to “ON”.
RS485: This parameter is used to enable or disable the RS485 communication. If
the RS485 communication cables are used, set this parameter to “ON”.
Baud Rate: This parameter is used to set the baud rate for the communication
between the Device and the PC. It includes five options: 9600, 19200, 38400, 57600,
and 115200. The high baud rate is recommended for the RS232 communication to
achieve high communication speed, while the low baud rate is recommended for the
RS485 communication to achieve stable low-speed communication.
Device ID: This parameter is used to set the ID of device from 1 to 254. If the
RS232/RS485 communication is adopted, you need to enter the device ID on the
software communication interface.
Comm. Key: To enhance the security of attendance data, you can set a password
for the connection between the Device and PC. Once the password is set, you can
connect the PC with the Device to access the attendance data only after entering the
correct password. The default password is 0 (that is, no password). Once a
password is set, you need to enter this password before connecting the PC software
with the Device; otherwise, the connection is unsuccessful. 1 to 6 digits passwords
are supported.
39
MultiBio700 User Manual 1.0
Considering the massive data including the fingerprint and face templates
stored in the device, it is recommended to transfer the data between the
device and PC over network to enhance the transfer speed.
40
5. Communication Settings
5.2 Wiegand Output
Wiegand Format: The system has two built-in formats
Wiegand 26-bits and Wiegand 34-bits, and also
supports the format customization function to meet
individualized requirements.
Failed ID: Refers to the value output by the system
upon verification failure. The output format is subject to
the setting of “Wiegand Format”. The default value
scope of Failed ID is 0–65535.
Site Code: The site code is used for customized
Wiegand format. The site code is similar to the device
ID, but the site code is customizable and can be
duplicated among different devices. The default value scope of the site code is
0–255.
Pulse Width: Refers to the width of the Wiegand pulse in microseconds. The default
value scope of the pulse width is 1–1000.
Pulse Interval: Refers to the interval of the Wiegand pulse in microseconds. The
default value scope of the pulse width is 1–10000.
Output: Refers to the contents output upon successful verification. You can select
the “User ID” or “Card Number” as the output.
41
MultiBio700 User Manual 1.0
5.2.1 Wiegand 26-bits Output Description
The system has a built-in Wiegand 26-bits format. Press [Wiegand Format], and
select “Standard Wiegand 26-bits”.
The composition of the Wiegand 26-bits format contains 2 parity bits and 24 bits for
output contents (“User ID” or “Card Number”). The binary code of 24-bits represent
up to 16,777,216 (0–16,777,215) different values.
1
2
Even parity
25 26
User ID/Card Number
Odd parity bit
Definition of Fields:
Field
Meaning
Even parity bit
Judged from bit 2 to bit 13. The even parity bit is 1 if the
character has an even number of 1 bits; otherwise, the
even parity bit is 1.
User
ID/
Card
User ID/Card Number (Card Code, 0–16777215)
Number (bit 2-bit 25)
Bit 2 is the Most Significant Bit (MSB).
Odd parity bit
Judged from bit 14 to bit 25. The odd parity bit is 1 if the
character has an even number of 1 bits; otherwise, the odd
parity bit is 0.
For example, for a user with user ID of 12345, the enrolled card number is
0013378512 and the failed ID is set to 1.
1. When the output is set to “User ID”, the Wiegand output is as follows upon
successful verification:
00000000000110000001110011
Even parity bit User ID = Binary code of 12345 Odd parity bit
2. When the output is set to “Card Number”, the Wiegand output is as follows upon
42
5. Communication Settings
successful verification:
11100110000100011110100000
Even parity bit User ID = Binary code of 0013378512 Odd parity bit
3. The Wiegand output is as follows upon verification failure:
00000000000000000000000010
Even parity bit Failed ID = Binary code of 1
Odd parity bit
" Note: If the output contents exceed the scope allowed for the Wiegand format,
the last several bits will be adopted and first several bits are automatically discarded.
For example, the user ID 888 888 888 is 110 100 111 110 110 101 111 000 111 000 in
binary format. Wiegand26 only supports 24 bits, that is, it only outputs the last 24 bits,
and first 6 bits “110 100” are automatically discarded.
43
MultiBio700 User Manual 1.0
5.2.2 Wiegand 34-bits Output Description
The system has a built-in Wiegand 34-bits format. Press [Wiegand Format], and
select “Standard Wiegand 34-bits”.
The composition of the Wiegand 34-bits format contains 2 parity bits and 32 bits for
output contents (“User ID” or “Card Number”). The binary code of 32-bits represent
up to 4,294,967,296 (0–4,294,967,295) different values.
1
2
33 34
EvenPari
User ID/Card Number
Odd parity bit
Table 2 Definition of Fields
Field
Meaning
Even parity bit
Judged from bit 2 to bit 17. The even parity bit is 1 if the
character has an even number of 1 bits; otherwise, the
even parity bit is 1.
User
ID/Card
User ID/Card Number (Card Code, 0–4,294,967,295)
Number (bit 2-bit 33)
Bit 2 is the Most Significant Bit (MSB).
Odd parity bit
Judged from bit 18 to bit 33. The odd parity bit is 1 if the
character has an even number of 1 bits; otherwise, the
odd parity bit is 0.
For example, for a user with user ID of 123456789, the enrolled card number is
0013378512 and the failed ID is set to 1.
1. When the output is set to “User ID”, the Wiegand output is as follows upon
successful verification:
0000001110101101111001101000101011
Even parity bit User ID = Binary code of 123456789
Odd parity bit
44
5. Communication Settings
2. When the output is set to “Card Number”, the Wiegand output is as follows upon
successful verification:
0000000001100110000100011110100001
Even parity bit User ID = Binary code of 0013378512
Odd parity bit
3. The Wiegand output is as follows upon verification failure:
0000000000000000000000000000000010
Even parity bit
Failed ID = Binary code of 1
Odd parity bit
45
MultiBio700 User Manual 1.0
5.2.3 Customized Format
Apart from the two built-in formats Wiegand 26-bits and Wiegand 34-bits, the
system also supports the format customization function to meet individualized
requirements.
The customized format consists of two character strings: the data bits and parity
bits. These two character strings need to be defined separately. Data bits define the
number of binary bits output by Wiegand as well as the meaning of each bit. The
data bits output by Wiegand can be a card number (C), site code (s), facility code (f),
manufacturer code (m) and parity bits (p). Parity bits define the check mode of each
bit in data bits and ensure the correctness of data bits during transfer through the
parity check. The parity bits can be set to odd check (o), even check (e) and both
odd check and even check (b). There exists a one-to-one correspondence
relationship between the data bits and parity bits.
For example, the Wiegand26 can be customized as follows:
Definition of data bits: pssssssssccccccccccccccccp
Definition of parity bits: eeeeeeeeeeeeeooooooooooooo
" Note: Wiegand26 consists of 26 bits. The first bit is
th
the even parity bit of bits 2 to 13; the 26 bit is the odd
parity bit of bits 14 to 25; the second to the ninth bits are
the site code; the 10th to the 25th bits are the card
number.
For details about the Wiegand protocol, see Appendix 3
Introduction of Wiegand.
To customize Wiegand format, proceed as follows:
(1) Select [Define Format] and the [Set] key is then
enabled.
46
5. Communication Settings
(2) Press [Set] to display the [User Define Format] interface, as shown in the
following figure:
(3) Click the entry box below “Card Format” to display the following interface:
Display Input
Display the Numb
Cancel Input
Backspace
Confirm Input
Clear Input
Characters used to define data bits and their meanings:
c: Indicates the card number, that is, the output contents,
it can be set to User ID/Card Number through menu
operations.
f: Indicates the facility code which is 0 by default. It is not
configurable. To modify it, please contact the equipment
supplier.
m: Indicates the manufacturer code which is 0 by default.
It is not configurable. To modify it, please contact the
equipment supplier.
p: Indicates the parity position.
s: Indicates the site code which can be set from 0 to 255
by default.
47
MultiBio700 User Manual 1.0
(4) Click the entry box below “Parity Format” to display the following interface:
Characters used to define parity bits and their meanings:
o: Indicates the odd check, that is, there is an odd number of 1’s in the bit sequence
(including one parity bit). For example, for 1000110(0), the parity bit is 0 and there
are already three 1’s. After 0 is suffixed to 1000110, there is still an odd number of
1’s.
e: Indicates the even check, that is, there is an even number of 1’s in the bit
sequence (including one parity bit). For example, for 1000110(1), the parity bit is 1
and there are already three 1’s. After 1 is suffixed to 1000110, there is an even
number of 1’s.
b: Indicates both odd check and even check.
For example: Definitions of several universal Wiegand formats.
Wiegand34
Data bits:
pccccccccccccccccccccccccccccccccp
Parity bits:
eeeeeeeeeeeeeeeeeooooooooooooooooo
Note: Wiegand34 consists of 34 bits. The first bit is the even parity bit of bits 2 to 17;
the 34th bit is the odd parity bit of bits 18 to 33; the second to the ninth bits are the
site code; the 10th to the 25th bits are the card number.
Wiegand37a
Data bits: pmmmmsssssssssssscccccccccccccccccccp
Parity bits: oeobeobeobeobeobeobeobeobeobeobeobeoe
Note: Wiegand37a consists of 37 bits. The first bit is the odd parity bit of bits 3, 4, 6,
7, 9, 10, 12, 13, 15, 16, 18, 19, 21, 22, 24, 25, 27, 28, 30, 31, 33, 34 and 36; the 37th
bit is the odd parity bit of bits 2, 4, 5, 7, 8, 10, 11, 13, 14, 16, 17, 19, 20, 22, 23, 25,
26, 28, 29, 31, 32, 34 and 35; bits 4, 7, 10, 13, 16, 19, 22, 25, 28, 31 and 34
48
5. Communication Settings
participate in both odd and even parity check. Bits 2 to 5 are manufacturer code; bits
6 to 17 are the site code; bits 18 to 36 are the card number.
Wiegand37
Data bits:
pmmmffffffffffssssssccccccccccccccccp
Parity bits:
eeeeeeeeeeeeeeeeeeooooooooooooooooooo
Note: Wiegand37 consists of 37 bits. The first bit is the even parity bit of bits 2 to 18;
the 34th bit is the odd parity bit of bits 19 to 36; the second to the fourth bits are the
manufacturer code; the 5th to the 14th bits are facilitate code; the 15th to the 20th bits
are the site code; the 21st to the 36th bits are the card number.
Wiegand50
Data bits: pssssssssssssssssccccccccccccccccccccccccccccccccp
Parity bits:
eeeeeeeeeeeeeeeeeeeeeeeeeooooooooooooooooooooooooo
Note: Wiegand50 consists of 50 bits. The first bit is the even parity bit of bits 2 to 25;
the 50th bit is the odd parity bit of bits 26 to 49; the second to the 16th bits are the site
code; the 17th to the 49th bits are the card number.
49
MultiBio700 User Manual 1.0
5.3 Wiegand Input
Wiegand Format: The system has two built-in formats
Wiegand 26-bits and Wiegand 34-bits, and also supports
the format customization function to meet individualized
requirements. About the Wiegand format, please refer to
5.2 Wiegand Output.
Bit counts: Wiegand data digit length
Pulse width: Pulse width is 100 microseconds by default,
which can be adjusted from 20 to 800.
Pulse interval: It is 900 microseconds by default, which
can adjusted between 200 and 20000.
Input: Content contained in Wiegand input signal,
including User ID or card number.
50
6. System Configuration
6. System Configuration
Through the [System] menu, you can set system-related parameters, including the
General, Display, Fingerprint, Face, Log settings, Shortcut Def, Access Control Set.
and Firmware Update, to enable the device to meet user requirements to the
greatest extent in terms of functions and display.
51
MultiBio700 User Manual 1.0
6.1 General Parameters
Keyboard Clicks: This parameter is used to set whether
to generate beep sound in response to every keyboard
touch. Select “ON” to enable the beep sound, and select
“OFF” to mute.
Voice Prompts: This parameter is used to set whether to
play voice prompts during the operation of the Device.
Select “ON” to enable the voice prompt, and select “OFF”
to mute.
Volume (%): This parameter is used to adjust the volume
of voice prompts.
Lock Power Key: This parameter is used to set whether
to lock the power key. Select “ON” to disable the power key. If you select “OFF” and
press the power key, the Device will be shut down in three seconds.
52
6. System Configuration
6.2 Interface Parameters
Language: This parameter is used to display the
current
language
used
by
the
Device.
For
multilingual-capable Devices, you can switch between
different languages through this parameter.
Toolbar: This parameter is used to display style of the
shortcut keys on the initial interface. It can be set to
“Auto Hide” and “Permanent Display”. By selecting
“Auto Hide”, you can manually display or hide the
toolbar. By selecting “Permanent Display”, you can
permanently display the toolbar on the initial interface.
Sleep Time (S): This parameter is used to specify a
period after which the Device is put in sleep mode if not operated within this period.
You can bring up the Device from sleep by pressing any key or touching the screen.
53
MultiBio700 User Manual 1.0
6.3 Fingerprint Parameters
1: 1 Threshold: This parameter is used to set the
threshold of matching between current fingerprint and
the fingerprint template enrolled in the device in the 1:1
verification mode. If the similarity between current
fingerprint and the fingerprint template enrolled in the
Device is larger than this threshold, the matching is
successful; otherwise, the matching is not successful.
1: N Threshold: This parameter is used to set the
threshold of matching between current fingerprint and
the fingerprint template enrolled in the device in the 1:N
verification mode. If the similarity between current
fingerprint and the fingerprint template enrolled in the Device is larger than this
threshold, the matching is successful; otherwise, the matching is not successful.
The recommended thresholds are as follows:
(FRR)
High
Medium
Low
(FAR)
Low
Threshold
1: N
1:1
45
25
Medium
35
15
High
25
10
Algorithm Version: This parameter is used to select the fingerprint algorithm
version between 9.0 and 10.0. Please select the algorithm version with caution
because the fingerprint templates of these two algorithm versions are incompatible.
Fingerprint Image: This parameter is used to set whether to display the fingerprint
image on the screen during fingerprint enrollment or comparison. It has four values:
Show For Enroll: Display the fingerprint on the screen in enrolling process.
Show For Match: Display the fingerprint on the screen in verification process.
54
6. System Configuration
Always Show: Display the fingerprint on the screen in enrolling and verifying
process.
Never Show: Never display the fingerprint on the screen in any case.
55
MultiBio700 User Manual 1.0
6.4 Face Parameters
1: 1 Threshold: This parameter is used to set the
threshold of matching between current face and the face
template enrolled in the Device in the 1:1 verification
mode. If the similarity between current face and the face
template enrolled in the Device is larger than this
threshold, the matching is successful; otherwise, the
matching is not successful. The valid value scope is
55─120. The higher the threshold, the lower the FAR and
the higher the FRR, and vice versa.
1:1: N Threshold: This parameter is used to set the
threshold of matching between current face and the face
template enrolled in the Device in the 1:N verification mode. If the similarity between
current face and the face template enrolled in the Device is larger than this threshold,
the matching is successful; otherwise, the matching is not successful. The valid
value scope is 65─120. The higher the threshold, the lower the FAR and the higher
the FRR, and vice versa.
The recommended thresholds are as follows:
FRR
FAR
High
Low
Threshold
1: N
1:1
90
80
Medium
Medium
80
70
Low
High
75
65
Exposure: This parameter is used to set the exposure value of the camera.
Gain: This parameter is used to set the gain value of the camera.
Quality: This parameter is used to set a quality threshold for the face images
obtained. The Device accepts the face images and processes them by adopting the
56
6. System Configuration
face algorithm when their quality is higher than the threshold; otherwise, it filters
these face images.
" Note: Improper adjustment of the Exposure, Gain and Quality parameters may
severely affect the performance of the Device. Please adjust the Exposure
parameter only under the guidance of the after-sales service personnel from our
company.
57
MultiBio700 User Manual 1.0
6.5 Log Settings
Log Alert: When the available space is insufficient to
store the specified number of attendance records, the
Device will automatically generate an alarm (Value
scope: 1-99).
Dup. Punch Period (m): If a user’s attendance record
already exists and the user punches in again within the
specified
period
(unit:
minute),
his/her
second
attendance record will not be stored (Value scope: 1-60
minutes).
58
6. System Configuration
6.6 Keyboard Definitions
Define touch screen functional shortcut keys.
1. Press [Shortcut Def] to display the [Edit] interface, as shown below.
2. If you want to cancel the shortcut key, press [Status] to enter the edit interface,
select the value to Undefine.
3. Edit the item [Code], select [Label] (Six attendance state option). Select if the
state [Auto Switch] value, the interface shown as figure above.
4. Press [Save] to save the modification and exit.
59
MultiBio700 User Manual 1.0
6.7 Access Setting
Access control setting is to set user’s open door time
zone, control lock and related device’s parameters.
To unlock, the enrolled user must accord with the
following conditions:
1. The current unlock time should be in the effective time
of user time zone or group zone.
2. The group where user is must be in access control (or
in the same access control with other group, to open the
door together).
The system default the new enrolled user as the first
group, default group time zone as 1, access control as
the first group, and the new enrolled user is in unlock (if user has modified the
related setting of access control, the system will be changed with user’s
modification.)
60
6. System Configuration
6.7.1 Time zone setting
Time zone is the minimum unit of access control option.
The whole system can define 50 time zones. Every time
zone defines seven time sections (namely, a week).
Every time section is the effective time zone within 24
hours everyday. Every user can set 3 time zones. “or”
exists among the three zones. It is effective if only one is
satisfied. Every time section format is HH:MM-HH:MM,
namely, accurate to minute.
If end time is smaller than start time (23:57- 23:56), the
whole day is forbidden. If end time is bigger than start
time (00:00- 23:59), it is effective section.
Effective time zone for user unlocking:00:00-23:59 or end time is bigger than start
time.
"
Notice: System default time zone 1 as whole day open (namely, the new
enrolled user is unlocking).
61
MultiBio700 User Manual 1.0
6.7.2 Holiday setting
Special access control time may need during holiday. It is
different to modify everybody’s access control time. So a
holiday access control time can be set, which is
applicable for all employees.
1. Add holiday:
(1) Enter holiday add interface, press the key to edit the
items.
(2) Press the touch screen number key to set the value,
after setting, press [OK] to save, and press [X] for exit
and return to previous interface.
(3) Press [Save] to save current information and return to previous interface; press
[Exit] to directly return to previous interface without saving current information.
62
6. System Configuration
2. Edit holiday
Select the holiday to be edit and enter the edit interface.
The edit operation is similar to add holiday. After edit,
press [Save] to save and return to previous interface.
" Notice: If holiday access control time is set, user’s
open door time zone during holiday subject to the time
zone here.
3. Delete holiday
Select the holiday to be deleted. Press [Delete] to
popup the confirm interface as follows. Select [Yes] to
delete this holiday, otherwise select [No] to cancel the
operation.
63
MultiBio700 User Manual 1.0
6.7.3 Group time zone setting
Grouping is to manage employees in groups. Employee
in groups use group time zone by default. Group
members can also set user time zone. Every group can
hold there time zones. The new enrolled user belongs to
Group 1 by default and can also be allocated to other
groups.
1. Add group time zone
(1) Enter the Add Group interface, press the key to edit
the items.
Code: Enter the number edit interface to set the value.
VerType: Select the Group Verify Type.
Holiday No.: Select if the Time zone is valid in holiday.
Time Zone: Select the Group Time Zone.
(2) After editing, press [Save] to save current information
and return to previous interface; press [Exit] to directly
return to previous interface without saving current
information.
" Note:
(1) RF means ID Card verification. Only the products with a built-in ID card module
support the ID card verification.
(2) For Multi-combination verification please refer to Appendix 4 Multi-combination
Authentication Mode.
64
6. System Configuration
" Notice:
1. If holiday is effective, only when there is intersection between group zone and
holiday time zone, can the group member open the door.
2. If holiday is ineffective, the access control time of group member won’t be affected
by holiday.
2. Edit group time zone
Select the line to be edited. Press OK directly or press
menu to select edit in operating menu. After editing,
press [Save] to save current information and return to
previous interface; press [Exit] to directly return to
previous interface without saving current information.
65
MultiBio700 User Manual 1.0
3. Delete group time zone
Select the line to be deleted. Press [Delete] to popup
the confirm interface as follows. Select [Yes] to delete
this holiday, otherwise select [No] to cancel the
operation.
66
6. System Configuration
6.7.4 Unlock Combination Setting
Make various groups into different access controls to achieve multi-verification and
improve security. An access control can be made up of 5 groups at most.
1. Add Unlock Combination
(1) Enter holiday add Combination Setting interface, press
the key to edit the items.
(2) Press the touch screen number key to set the value,
after setting, press [OK] to save, and press [X] for exit and
return to previous interface.
(3) Press [Save] to save current information and return to
previous interface; press [Exit] to directly return to previous
interface without saving current information.
67
MultiBio700 User Manual 1.0
2. Edit Unlock Combination
Select the line to be edited. Press OK directly or press
menu to select edit in operating menu. After editing,
press [Save] to save current information and return to
previous interface; press [Exit] to directly return to
previous interface without saving current information.
3. Delete Unlock Combination
Select the line to be deleted. Press [Delete] to popup
the confirm interface as follows. Select [Yes] to delete
this holiday, otherwise select [No] to cancel the
operation
68
6. System Configuration
6.7.5 Access control parameter
Through the [Access] menu, you can set the parameters
of the electronic locks and related access control
devices.
Lock Delay: indicates the duration for the Device to
place the electric lock in open state. (Value scope: 1–10
seconds)
Door Sensor Delay: indicates the delay in checking the
door sensor after the door is open. If door sensor state is
inconsistent with the normal state set by the door sensor
switch, an alarm will be generated, and this period of time
is regarded as the “door sensor delay”. (Value scope:
1─99 seconds)
Door Sensor Mode: includes the None, Normally Open (NO), and Normally Closed
(NC) modes. “None” indicates that the door sensor switch is not used. “NO” indicates
that the door sensor is open in the normal state. “NC” indicates that the door sensor
is closed in the normal state.
Alarm Delay: indicates the duration from the detection of door sensor exceptions to
the generation of alarm signals. (Value scope: 1─99 seconds)
Failure Alarm Threshold: When the failed press times reach the set times, alarm
signal will come out.(effective value 1~9 times)
NC Time Zone: Set time zone for access control NC. Nobody can unlock during this
time zone.
NO Time Zone: Set time zone for access control NO. The lock is always in enabling
state during this time zone.
Valid in Holiday: Define time zone for NO or NC. Whether the time zone set in time
zone is effective.
Notice:1. When time zone is set for NO or NC, please set door
sensor mode as None, or alarm signal may come out during time zone of NO or NC.
69
MultiBio700 User Manual 1.0
" Notice:
1. If the Time Zone of normally open or normally closed has been set, please switch
door sensor to no, otherwise it will produce alarm signal during Normal close Time
Zone or Normal open Time Zone .
2. If the normally open or normally closed Time Zone is not defined yet the time, the
equipment will prompt that you define the Time Zone, and transferred to the Time
Zone interface, to adding.
70
6. System Configuration
6.7.6 Duress alarm parameter
There is duress alarm parameter setting in the device.
When employee come across duress, select duress
alarm mode, the device will open the door as usual. But
the alarm signal will be sent to the alarm.
1:1
Trigger: if select “Yes”, when user use 1:1 match
mode, alarm signal will come out. Or there is no alarm
signal.
1:N
Trigger: if select “Yes”, when user use 1:N match
mode, alarm signal will come out. Or there is no alarm
signal.
Password Trigger: If select “Yes”, when user use
password verification mode, alarm signal will come out. Or there is no alarm signal.
Alarm Delay: After duress alarm gets started, the alarm signal is not output directly.
But it can be defined. After some time, alarm signal will be generated automatically
(0-255 seconds).
71
MultiBio700 User Manual 1.0
6.7.7 Anti-Pass back setting
Set the device Anti-Pass back function.
APB Direction: There are four options: None, APB-Out,
APB-In, APB-Out/In.
Device Status: There are three options: Exit Control,
Entry Control and none.
Anti-Pass back function please refer to Appendix 5
Anti-Pass back.
Anti-Pass back setting operation:
(1) Enter Anti-Pass back setting interface, press the key to
edit the items.
(2) Press the touch screen number key to set the value,
after setting, press [OK] to save, and press [X] for exit and return to previous
interface.
(3) Press [Save] to save current information and return to previous interface; press
[Exit] to directly return to previous interface without saving current information.
72
6. System Configuration
6.8 Update
You can upgrade the firmware program of the device by
using the upgrade file in the USB disk through this
function.
If you need the firmware upgrade file, please contact our technical
support
personnel.
Generally
the
firmware
upgrade
is
not
recommended.
73
7. Data Management
7. Data Management
Through the [Data Mgt.]
menu, you can perform
management of data stored
on the device, for example,
deleting
the
attendance
record,
all
data
promotional
and
pictures,
purging management rights
and resetting the device to
factory defaults.
1. Delete Transactions: Delete all the attendance records.
2. Delete All Data: Delete all the information of enrolled personnel, including their
fingerprints, face images and attendance records.
3. Clear Administrator: Change all administrators to ordinary users.
4. Restore to Factory Settings: Restore all parameter settings on the device to
factory settings.
" Notice: The employee information and attendance records will not be deleted
during restoration to factory settings.
5. Query Record: After check-in successfully, the employee’s attendance records
are saved in the device. You can easily query these attendance records.
User ID: Enter the user ID of the employee to query. If this field is left blank, you can
query the attendance records of all the employees. If you enter a user ID, you can
query the attendance record of the employee with this user ID.
Query Time Period: Select a time period to query, including the customized time
74
7. Data Management
period, yesterday, this week, last week, this month, last month, and all time periods.
Start and End: When you select a customized time period, you need to input a start
time and an end time. When you select other options for time period, the start and
end time will be automatically adjusted to the related time.
After setting the query conditions, press [Query] and the records that meet the
specified query conditions will be displayed on screen.
Select the row where the desired record is located, you can query the detailed
information of this records.
Press User ID and enter the edit interface, input the ID number and press [Query],
the query result will display as below.
75
MultiBio700 User Manual 1.0
76
8. Date/Time Setting
8. Date/Time Setting
8.1 Set Date/Time
The date and time of the device must be set accurately to
ensure the accuracy of attendance time.
1. Press [Menu] on the initial interface to display the main
menu interface.
2. Press [Time/Date] on the main menu interface to
display the time setting interface.
3. Select the desired date and time by pressing the
parameter. For the time format, there 10 format to select.
Both the 12-hour and 24-hour time systems are
supported.
4. Press [Save] to save current information and return to
the previous interface. Press [Exit] to return to the previous interface without saving
current information.
77
MultiBio700 User Manual 1.0
8.2 Bell Setting ★
Lots of companies need to ring their bells to signal the start and end of work shifts,
and they usually manually ring their bells or use electric bells. To lower costs and
facilitate management, we integrate the time bell function into the device. You can
set the alarm time and duration for ringing the bell based on your requirements, so
that the device will automatically play the selected ring tone and trigger the relay at
the alarm time, and stop playing the ring tone after the set duration.
Press [Bell] on the [Date/Time] menu to display the bell setting interface, as shown
in Figure below.
1. Add a bell
1) The displayed bell setting interface lists all the bells. Click [Add] to display the
[Add] interface.
2) On the [Add] interface, set the following parameters:
Bell Time: This parameter is used to set a time point when the Device automatically
plays a bell ring tone everyday.
Bell Date: This parameter is used to set which day the device automatically plays a
bell ring tone.
78
8. Date/Time Setting
Ring Tone: This parameter is used to set the bell ring tone.
Volume: This parameter is used to set the volume of ring tone.
Repeat: This parameter is used to set the alarm times.
State: This parameter is used to set whether to enable the bell.
Bell Type: You can select between internal ringing or external ringing. For internal
ringing, the ring tone is played by the loudspeaker of the device. For external ringing,
the ring tone is played by an external electric bell that is wired with the device.
2. Edit and delete a bell
Press a bell in the list on the bell setting interface to
display the [Edit] interface, with the similar operation as
“Add a bell”.
" Notice: Only some models have this function. If you need it, please contact our
business representative or technician.
79
9. Auto Test
9. Auto Test
The auto test enables the system to automatically test whether functions of various
modules are normal, including the screen, collector, voice, face, keyboard and clock
tests.
1. Test Screen: The device automatically tests the display effect of the color TFT
display by displaying full color, pure white and pure black and checks whether the
screen displays properly. You can continue the test by touching the screen or exit it
by pressing [Exit].
2. Test Fingerprint: The device automatically tests whether the fingerprint collector
works properly by checking whether the fingerprint images are clear and acceptable.
When the user places his/her finger in the fingered guide, the collected fingerprint
image is displayed on the screen in real-time. Press [Exit] to exit the test.
3. Test Voice: The device automatically tests whether the voice files are complete
and the voice quality is good by playing the voice files stored in the device. You can
continue the test by touching the screen or exit it by pressing [Exit].
4. Test Face: The device automatically tests whether the camera works properly by
80
9. Auto Test
checking whether the collected face images are clear and acceptable. Press [Auto
Test] to exit the test.
5. Test Keyboard: The device tests whether every key on the keyboard works
normally. Press any key on the [Keyboard Test] interface to check whether the
pressed key matches the key displayed on screen. The keys are dark-gray before
pressed, and turn blue after pressed. Press [Exit] to exit the test.
6. Test Time: The device tests whether its clock works properly by checking the
stopwatch of the clock. Touch the screen to start counting, and touch it again to stop
to check whether the counting is accurate. Press [Exit] to exit the test.
7. Screen Calibration:
You can perform all the menu operations by touching the screen with one of your
fingers or a touch pen. When the touch screen is less sensitive to the touch, you can
perform screen calibration through menu operations.
The Screen Calibration Operation:
(1) Press [Menu] on the initial interface to display the main
menu interface.
(2) Press [Calibration] on the [Auto Test] interface to
display the screen calibration interface.
(3) Touch the center of the cross “+”.
(4) Repeat Step 3 following the move of the “+” icon to
different locations on the screen.
(5) Touch the center of the cross at five locations on the
screen correctly. When the message “Calibrating screen,
pls wait……” is displayed on screen, the calibration
succeeds and the system automatically returns to the main
menu. If the calibration fails, the system will request recalibration starting from Step
3.
81
10. USB Disk Management
10. USB Disk Management
Through the [Dn/Upload] menu, you can import user information and attendance data
stored in a USB disk to related software or other fingerprint recognition equipment.
1. Download Transactions: Import all the attendance data from the device to a USB
disk.
2. Download User: Import all the user information, fingerprints and face images from the
device to a USB disk.
3. Download user photos: Import the employees’ photos from the device to a USB disk.
4. Upload User: Upload the user information, fingerprints and face images stored in a
USB disk to the device.
5. Upload User Photo: Upload the JPG documents that are named after the user IDs
and stored in a USB disk to the device, so that user photos can be displayed after the
employees pass the verification. See Appendix 3 Photo ID Function.
82
11. System Information
11. System Information
You can check the storage status as well as version
information
of
the
device
through
the
[System
Information] option.
Records: The number of enrolled users, administrators
and passwords is displayed on the [Records] interface;
the total fingerprint storage capacity and occupied
capacity as well as the total attendance storage
capacity
and
occupied
capacity
are
graphically
displayed respectively.
Device: The device name, serial number, version
information, vendor and date of manufacture are
displayed on the [Device] interface.
83
12. Appendix
12. Appendix
Appendix 1 T9 Input Instructions
The Device supports the input
of
English
characters,
numbers and symbols. Press
related button to input text. For
example,
press
[Name]
to
display the text input interface,
as shown in the figure:
①Keyboard Area
②Text DisplayArea
③Text List Area
④Exit
⑤Delete
⑥Enter
⑦Space
⑨Character/English
⑩Upper/Lower Case
84
12. Appendix
To enter a name, proceed as follows:
1. Press [Name] on the [Add] interface, as shown in Figure below.
2. Enter the letter characters, and a list of characters in relation to the letter is
presented in the text display area.
3. If the desired character is displayed in the text display area, press this character.
And this character is at the same time displayed on the [Name] button. Enter next
character by repeating Step 2.
4. After finishing the entry of name, press [X] to exit keyboard interface and return to
the previous interface.
85
MultiBio700 User Manual 1.0
Appendix 2 Introduction of Wiegand
Wiegand26 is an access control standard protocol established by the Access Control
Standard Subcommittee affiliated to the Security Industry Association (SIA). It is a
non-contact IC card reader interface and output protocol.
Wiegand26 defines the interface between the card reader and controller used in the
access control, security and other related industrial fields. Wiegand26 helps
standardize the work of the card reader designers and controller manufacturers. The
access control products manufactured by our company are also designed by
following this protocol.
Digital Signals
The figure below is a sequence diagram in which the card reader sends digital
signals in bit format to the access controller. In this sequence diagram, Wiegand
follows the SIA’s access control standard protocol for the 26-bit Wiegand card
reader (one pulse time ranges between 20us and 100us, and the pulse jump time
ranges between 200us and 20ms). Data1 and Data0 are high level (larger than Vol)
signals till the card reader prepares to send a data stream. The asynchronous
low-level pulse (smaller than Vol) generated by the card reader is sent to the access
control panel (The saw-tooth wave as shown in Figure below) through Data1 or
Data0. Data1 and Data0 pulses will neither overlap nor be generated synchronously.
The table below lists the maximum and minimum pulse width (a consecutive pulse)
and pulse jump time (time between pulses) allowed by the F series fingerprint
access control device.
86
12. Appendix
Figure: Sequence Diagram
Table: Pulse Time
Symbol
Definition
Typical Value of Reader
Tpw
Pulse Width
100 µs
Tpi
Pulse Interval
1 ms
87
MultiBio700 User Manual 1.0
Appendix 3 Photo ID Function
Some Devices also support the Photo ID function. The
Photo ID function is used to display the photo enrolled
by a user or stored in a USB disk on the screen in
addition to such information as the user ID and name.
[Operation Steps]
1. When the photo taken by the device is used, the
photo can be displayed upon successful verification.
2. To use a photo stored in a USB disk, proceed as
follows:
1) Create a folder with the name of “photo” in the USB
disk, and store users' photos under this folder.
2) The user photos must be in JPG format and named
after their IDs. For example, for the user with user ID of 154, the photo name must
be 154.jpg.
3) Insert the USB disk into USB slot on the device, and select USB Disk
Management -> Upload -> Upload Photos. Then user photos can be displayed upon
successful verification.
" Note:
1) The length of a user name cannot exceed 24 digits.
2) The recommended size of a user photo is less than 30kbit.
3) The uploaded new user photo will overwrite the existing photo in related to the
user ID.
4) To download user photos, select USB Disk Management -> Download ->
Download User Photos. A folder with the name of “photo” will be automatically
created on the USB disk, and all downloaded user photos are stored under this
folder.
88
12. Appendix
Appendix 4 Multi-combination Authentication Mode ★
Besides this function only is owned by the fingerprint access control machine that
has been appointed, the most fingerprint machine only has two way to verified by
fingerprint and password, we provide a personal or group Multi-combination
Authentication Mode for high security Access control area, verification type main
include five elements that are User Number (PIN), Fingerprint (FP), Face (FACE),
Password (PW) and RF card (RF), which can combine into multi-combination.
"
Note: The RF card is used for ID Card verification, the function of ID card
verification only is validity in the machine which ID card function is provided with.
These symbols illustrate what follow the table different means.
● “/” is or
●”+” follow next operation
● “&” is and
● FACE (Face)
● FP (fingerprint)
● PWD (Password)
● RF (RF card)
● PIN (user ID)
If Fingerprint, Face, Password and Card has been used to enroll user, the
verification procedure is follow.
Type
FACE&PIN/FP/PW/RF
What you do
FACE+PIN or RF or PW or RF is verified
1) PIN++FACE(1:1)
2) FP(1:N)
3) PIN+PW+“OK”
4) RF(1:N)
FP&PW
FP + PW are verified
1) FP(1:N)+PW+“OK”
89
MultiBio700 User Manual 1.0
2) PIN+FP(1:1)+PW+“OK”
3) PIN+PW+“OK”+FP
FP&RF
FP and RF are verified
1) RF+FP(1:1)
2) FP(1:N)+RF
3) PIN+FP(1:1)+RF
FACE&FP
FACE + FP are verified
1) FP(1:N)+FACE
2) FACE(1:N)+FP
3) PIN+FACE(1:1)+FP
4) PIN+FP(1:1)+FACE
FACE&PW
FACE + PW are verified
1) FACE(1:N)+PW+“OK”
2) PIN+FACE(1:1)+PW
3) PIN+PW+FACE
FACE&RF
FACE + RF are verified
1) FACE(1:N)+RF
2) PIN+FACE(1:1)+RF
3) RF(1:N)+FACE
FP
Only FP is verified.
1) PIN+FP(1:1)
2) FP(1:N)
PW
Only verify PW is verified
PIN+PW+“OK”
RF
Only RF is verified
RF(1:N)
FACE&PIN
FACE + PIN are verified
PIN+FACE(1:1)
90
12. Appendix
FP/RF
FP or RF is verified
1) PIN+FP(1:1)
2) RF(1:N)
3) FP(1:N)
PW/RF
FP or RF is verified
1) PIN+PW+“OK”
2) RF(1:N)
FP/PW
FP or PW is verified
1) PIN+FP(1:1)
2) FP(1:N)
3) PIN+PW+“OK”
PIN&FP
PIN + FP are verified
PIN+FP(1:1)
FP&PW&RF
FP + PW + RF are verified
1) FP(1:N)+PW+“OK”+RF
2) PIN+FP(1:1)+PW+“OK”+RF
3) RF(1:N)+PW+“OK”+FP
4) PIN+ PW+“OK”+FP(1:1)+RF
PIN&FP& PW
PIN + FP + PW are verified
1) PIN+PW+“OK”+FP(1:1)
2) PIN+FP(1:1)+PW+“OK”
FP & RF/PIN
FP + PIN, or FP + RF are verified
1) RF+FP(1:1)
2) FP(1:N)+RF
3) PIN+FP(1:1)
FACE&FP&RF
FACE + FP + RF are verified
1) FACE(1:N)+FP+RF
2) FP+FACE(1:1)+RF
91
MultiBio700 User Manual 1.0
3) RF(1:N)+FACE+FP
4) PIN+FP(1:1)+FACE+RF
5) PIN+FACE(1:1)+FP+RF
FACE&FP&PW
FACE + FP + PW are verified
1) FACE(1:N) +PW+“OK”+FP
2) FP+PW+“OK”+FACE(1:1)
3) PIN+FP(1:1) +PW+“OK”+FACE
4) PIN+FACE(1:1) +PW+“OK”+FP
5) PIN+PW+“OK”+FP+FACE
" Note: For combined verification, it is better to enroll all the elements in need of
the using verification mode, or verification will fail.
For example: User A use fingerprint for enrollment, while password is used for
verification, then the user cannot pass the verification.
92
12. Appendix
Appendix 5 Anti-Pass Back ★
【overview】
Sometimes, some illegal person follows the other one into the gate, which will
bring security problem. To prevent such risk, this function is enabled. In
record must match out record, or the gate won’t be open.
This function needs two machines to work together. One is installed inside
the door (master machine hereinafter), the other is installed outside the door
(slave machine hereinafter). Wigand signal communication is adopted
between the two machines.
【working principle】
The master machine has Wigand In and slave machine has Wigand Out.
Connect Wigand Out of slave machine to Wigand In of master machine.
Wigand output from slave machine must not own machine ID. The number
sent to master machine from slave machine must be found in the master
machine.
【function】
Judge whether it is anti-pass back according to user’s recent in-out record. In
record and out record must be matched. This machine supports out, in, or
93
MultiBio700 User Manual 1.0
out-in anti-pass back.
When master machine is set as “out anti-pass back”, if user wants to come in
and go out normally, his recent record must be “in”, or he cannot go out. Any
“out” record will be “anti-pass back refused”. For example, a user’s recent
record is “in”, his second record can be “out” or “in”. His third record is based
on his second record. Out record and in record must match.(Notice: If
customer has no record before, then he can come in but cannot go out. )
When the master machine is set as “in anti-pass back”, if the user wants to
come in and go out normally, his recent record must be “out”, or he cannot go
out. Any out record will be “anti-pass back refused” by the system. (Notice:
If the customer has no former record, then he can go out, but cannot come
in. )
When the master machine is set as “out-in anti-pass back”, if the user wants
to come in and go out normally, if his recent record is “out” and “in”, then his
next record must be “ in” and “out”.
【operation】
1. Select model
Master machine: Machine with Wiegand in function, except for F10 reader.
Slave machine: Machine with Wiegand Out function.
2. Menu setting
Anti-pass back
There are four options: in/out anti-pass back, out anti-pass back, in anti-pass
back, and none.
Out anti-pass back: Only user’s last record is in-record, can the door be
open.
In anti-pass back: Only user’s last record is out-record, can the door be
open.
Device status
There are three options: Control-in, control-out and none
94
12. Appendix
Control-in: When it is set, the verified record on the device is in-record.
Control-out: When it is set, the verified record on the device is out-record.
None: When it is set, close the device’s anti-pass back function.
3. Modify device’s Wiegand output format
When the two devices are communicating, only Wiegand signals without
device ID are received. Enter device menu-> communication option->
Wiegand option or enter software -〉basic setting -〉device management -〉
Wiegand, to modify “defined format” as “wiegand26 without device ID”.
4. Enroll user
The user must be on master machine and slave machine at the same time,
and user PIN must be the same. Therefore, it is necessary to enroll user on
master machine and slave machine at the same time.
5. Connection instruction
Wiegand communication is adopted for master machine and slave machine.
Refer to the following for connection:
Master
Slave
IND0
<----->
WD0
IND1
<----->
WD1
GND
<----->
GND
95
MultiBio700 User Manual 1.0
Appendix 6 Statement on Human Rights and Privacy
Dear Customers:
Thank you for choosing the hybrid biometric products designed and manufactured
by us. As a world-renowned provider of biometric technologies and services, we pay
much attention to the compliance with the laws related to human rights and privacy
in every country while constantly performing research and development.
We hereby make the following statements:
1.
All of our fingerprint recognition devices for civil use only collect the
characteristic points of fingerprints instead of the fingerprint images, and
therefore no privacy issues are involved.
2.
The characteristic points of fingerprints collected by our products cannot be
used to restore the original fingerprint images, and therefore no privacy issues
are involved.
3.
We, as the equipment provider, shall not be held legally accountable, directly or
4.
For any dispute involving the human rights or privacy when using our products,
indirectly, for any consequences arising due to the use of our products.
please contact your employer directly.
Our fingerprint products for police use or development tools support the collection of
the original fingerprint images. As for whether such a type of fingerprint collection
constitutes an infringement of your privacy, please contact the government or the
final equipment provider. We, as the original equipment manufacturer, shall not be
held legally accountable for any infringement arising thereof.
The law of the People’s Republic of China has the following regulations regarding
the personal freedom:
1.
Unlawful arrest, detention or search of citizens of the People's Republic of
China is prohibited; infringement of individual privacy is prohibited.
2.
The personal dignity of citizens of the People's Republic of China is inviolable.
96
12. Appendix
3.
The home of citizens of the People's Republic of China is inviolable.
4.
The freedom and privacy of correspondence of citizens of the People's
Republic of China are protected by law.
At last we stress once again that biometrics, as an advanced recognition technology,
will be applied in a lot of sectors including e-commerce, banking, insurance and legal
affairs. Every year people around the globe suffer from great loss due to the
insecurity of passwords. The biometric products actually provide adequate
protection for your identity under a high security environment.
97
Privacy Statement
Appendix 7 Environment-Friendly Use Description
The Environment Friendly Use Period (EFUP) marked on this product refers to the
safety period of time in which the product is used under the conditions specified in
the product instructions without leakage of noxious and harmful substances.
The EFUP of this product does not cover the consumable parts that need to be
replaced on a regular basis such as batteries and so on. The EFUP of batteries is
5 years.
Names and Concentration of Toxic and Hazardous Substances or Elements
Parts Name
Toxic and Hazardous Substances or Elements
Pb
Hg
Cd
Cr6+
PBB
PBDE
Chip resistor
×
○
○
○
○
○
Chip capacitor
×
○
○
○
○
○
Chip inductor
×
○
○
○
○
○
Chip diode
×
○
○
○
○
○
ESD components
×
○
○
○
○
○
Buzzer
×
○
○
○
○
○
Adapter
×
○
○
○
○
○
Screws
○
○
○
×
○
○
○: Indicates that this toxic or hazardous substance contained in all of the homogeneous
materials for this part is below the limit requirement in SJ/T11363-2006.
×: Indicates that this toxic or hazardous substance contained in at least one of the
homogeneous materials for this part is above the limit requirement in SJ/T11363-2006.
Note: 80% of the parts in this product are manufactured with non-hazardous
environment-friendly materials. The hazardous substances or elements contained cannot be
replaced with environment-friendly materials at present due to technical or economical
constraints.
98
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement