Elektron SPS-1 UW, MKII, UW MKII drum machine User’s Manual

FCC compliance statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residentpial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
European Union regulation compliance statement
This product has been tested to comply with the 2004/108/EC EMC Directive and the 72/23/EC Low Voltage directive.
This symbol indicates that your product must be disposed of properly according to local laws and regulations.
The included switched-mode power supply is CEC Level IV compliant.
The device contains a non rechargable lithium perchlorate battery cell that may need to be recycled separately depending on local environmental laws. If the battery needs replacing, please contact Elektron or a local professional
technician for servicing.
INTRODUCTION...........................................................................................................1-1
CONVENTIONS IN THIS MANUAL..................................................................................................... 1-1
THE STORY OF THE MACHINEDRUM .......................................................................1-2
MACHINEDRUM SPS-1 MKII/SPS-1UW MKII MAIN FEATURES ...................................................... 1-2
USER INTERFACE AND CONNECTORS....................................................................1-4
FRONT PANEL .................................................................................................................................... 1-4
REAR CONNECTORS ........................................................................................................................ 1-6
RACK MOUNT KIT (ACCESSORY) .................................................................................................... 1-7
RACK MOUNT KIT ASSEMBLY ..................................................................................................... 1-7
CONNECTING THE UNIT ................................................................................................................... 1-7
CARE INSTRUCTIONS ....................................................................................................................... 1-7
THE LCD USER INTERFACE ......................................................................................1-9
LAYER EDIT AND WINDOWS ............................................................................................................ 1-9
QUICK START ............................................................................................................1-10
PLAYING AND TWEAKING DRUM SOUNDS................................................................................... 1-10
USING THE TRACK EFFECTS......................................................................................................... 1-10
SELECTING AND PLAYING A PATTERN ......................................................................................... 1-10
RECORDING A PATTERN USING GRID RECORDING ................................................................... 1-11
SETTING THE ACCENT PATTERN .................................................................................................. 1-11
SETTING THE SWING PATTERN..................................................................................................... 1-11
PATTERN LIVE RECORDING........................................................................................................... 1-12
PARAMETER LOCKS........................................................................................................................ 1-12
THE SOUND SYNTHESIS OF MACHINEDRUM .......................................................1-13
MACHINEDRUM KITS....................................................................................................................... 1-14
LOADING A KIT............................................................................................................................ 1-14
SAVING AND NAMING A KIT ...................................................................................................... 1-15
UNDO KIT..................................................................................................................................... 1-16
COPY KIT ..................................................................................................................................... 1-16
CLEAR KIT ................................................................................................................................... 1-17
KIT ASSEMBLY ............................................................................................................................ 1-17
SETTING MUTE AND TRIG RELATIONS OF A KIT.................................................................... 1-18
COPY MACHINE .......................................................................................................................... 1-19
CLEAR MACHINE ........................................................................................................................ 1-20
MACHINE PARAMETER EDITING.................................................................................................... 1-21
THE TRACK EFFECTS ..............................................................................................1-22
AMPLITUDE MODULATOR.......................................................................................................... 1-22
TRACK EQ ................................................................................................................................... 1-23
FILTER.......................................................................................................................................... 1-23
THE SAMPLE RATE REDUCER.................................................................................................. 1-24
THE ROUTING PAGE.................................................................................................1-25
DISTORTION................................................................................................................................ 1-25
VOLUME....................................................................................................................................... 1-25
PAN............................................................................................................................................... 1-26
DELAY SEND ............................................................................................................................... 1-26
REVERB SEND ............................................................................................................................ 1-26
LFO CONTROL ............................................................................................................................ 1-27
THE STEREO MASTER EFFECT SYSTEM .............................................................1-28
THE RHYTHM ECHO DELAY ...................................................................................................... 1-29
THE GATE BOX REVERB............................................................................................................ 1-30
MASTER EQ................................................................................................................................. 1-30
I of VI
THE DYNAMIX DYNAMICS PROCESSOR ................................................................................. 1-31
LOW FREQUENCY OSCILLATORS (LFO’s) ............................................................ 1-32
THE PATTERN SEQUENCER................................................................................... 1-35
CLASSIC VS EXTENDED ................................................................................................................. 1-35
CLASSIC EDITING ....................................................................................................................... 1-35
EXTENDED EDITING................................................................................................................... 1-35
TEMPO .............................................................................................................................................. 1-36
THE TEMPO SCREEN ................................................................................................................. 1-36
TAP TEMPO ................................................................................................................................. 1-36
EXTERNAL SYNCHRONIZATION ............................................................................................... 1-36
PATTERN MODE ............................................................................................................................... 1-37
PATTERN SELECTION ................................................................................................................ 1-37
PATTERN CHAINING ................................................................................................................... 1-37
PARAMETER TWEAKING............................................................................................................ 1-37
SCALE SETUP ............................................................................................................................. 1-38
COMPOSING A PATTERN ................................................................................................................ 1-39
GRID RECORDING ...................................................................................................................... 1-39
PATTERN PAGE FUNCTIONALITY ON MKI UNITS.................................................................... 1-39
LIVE RECORDING ....................................................................................................................... 1-39
NOTE COPY................................................................................................................................. 1-40
CLEAR NOTE PARAMETER LOCKS........................................................................................... 1-40
TRACK COPY............................................................................................................................... 1-41
CLEAR TRACK............................................................................................................................. 1-41
TRACK PAGE COPY.................................................................................................................... 1-42
CLEAR TRACK PAGE .................................................................................................................. 1-42
PATTERN COPY .......................................................................................................................... 1-43
CLEAR PATTERN......................................................................................................................... 1-44
TRACK MUTING................................................................................................................................ 1-44
THE TRACK MUTE WINDOW...................................................................................................... 1-44
MINIMISING THE MUTE WINDOW ............................................................................................. 1-45
ACCENT TRACK ............................................................................................................................... 1-45
SWING............................................................................................................................................... 1-46
THE SWING WINDOW................................................................................................................. 1-46
PARAMETER LOCKS........................................................................................................................ 1-47
PARAMETER LOCKS IN GRID RECORDING MODE ................................................................. 1-47
PARAMETER LOCKS IN LIVE RECORDING MODE .................................................................. 1-48
PARAMETER LOCK SLIDE............................................................................................................... 1-49
SONG MODE.............................................................................................................. 1-51
LOAD SONG................................................................................................................................. 1-51
PLAYING A SONG........................................................................................................................ 1-52
NAVIGATING A SONG ................................................................................................................. 1-52
SONG EDITING............................................................................................................................ 1-52
SONG ROW OFFSETS AND LENGTHS...................................................................................... 1-54
SONG TRANSPORT .................................................................................................................... 1-54
SONG LOOP ................................................................................................................................ 1-54
SONG JUMP................................................................................................................................. 1-55
SONG HALT ................................................................................................................................. 1-55
SONG MUTE ................................................................................................................................ 1-55
SAVE SONG ................................................................................................................................. 1-56
GLOBAL SETTINGS .................................................................................................. 1-57
TURBO MENU................................................................................................................................... 1-57
CONTROL ......................................................................................................................................... 1-58
II of VI
BASE CHANNEL ............................................................................................................................... 1-58
MAP EDITOR..................................................................................................................................... 1-59
LOCAL CONTROL ............................................................................................................................ 1-60
PROGRAM CHANGE ........................................................................................................................ 1-61
MECHANICAL SETTINGS (MKII UNITS ONLY) ............................................................................... 1-61
ROUTING .......................................................................................................................................... 1-62
OUTPUT ............................................................................................................................................ 1-62
TRIG .................................................................................................................................................. 1-63
FILE ................................................................................................................................................... 1-63
SYSEX SEND .................................................................................................................................... 1-64
ALL DATA SYSEX SEND ............................................................................................................. 1-65
GLOBAL SYSEX SEND ............................................................................................................... 1-66
SONG + PATTERN (+ KIT) SYSEX SEND................................................................................... 1-66
PATTERN (+ KIT) SYSEX SEND ................................................................................................. 1-66
KIT SYSEX SEND ........................................................................................................................ 1-66
SYSEX RECEIVE ......................................................................................................................... 1-66
GENERAL SYSEX RECEIVE....................................................................................................... 1-67
ORIGINAL PLACE SYSEX RECEIVE .......................................................................................... 1-68
SPECIFIC PLACE SYSEX RECEIVE........................................................................................... 1-68
SYSEX VERIFY............................................................................................................................ 1-69
SAMPLE MANAGER (SPS-1UW/SPS-1UW MKII ONLY) ................................................................. 1-70
THE DIFFERENCE BETWEEN ROM AND RAM MACHINES..................................................... 1-71
RAM TO ROM COPY ................................................................................................................... 1-71
GENERAL SAMPLE RECEIVE .................................................................................................... 1-72
SPECIFIC PLACE SAMPLE RECEIVE ........................................................................................ 1-73
ORIGINAL PLACE SAMPLE RECEIVE ....................................................................................... 1-74
SEND SAMPLES.......................................................................................................................... 1-74
ERASE SAMPLES........................................................................................................................ 1-75
SYNC ................................................................................................................................................. 1-75
TEMPO IN .................................................................................................................................... 1-76
CTRL IN........................................................................................................................................ 1-76
TEMPO OUT ................................................................................................................................ 1-77
CTRL OUT.................................................................................................................................... 1-78
EARLY STARTUP MENU ...........................................................................................1-79
TEST MODE ...................................................................................................................................... 1-79
EMPTY RESET.................................................................................................................................. 1-79
FACTORY RESET ............................................................................................................................. 1-79
SOFT RESET .................................................................................................................................... 1-79
MIDI UPGRADE ................................................................................................................................ 1-79
SEND UPGRADE .............................................................................................................................. 1-81
TECHNICAL INFORMATION......................................................................................1-82
SPECIFICATIONS ............................................................................................................................. 1-82
DIFFERENCES BETWEEN THE MKI AND MKII MODELS ......................................1-83
DESIGN ............................................................................................................................................. 1-83
POWER SUPPLY .............................................................................................................................. 1-83
S/N RATIO AND OUTPUTS .............................................................................................................. 1-83
SAMPLER SPECIFICATIONS (UW MODELS ONLY) ....................................................................... 1-83
PATTERN LENGTH ........................................................................................................................... 1-83
CREDITS.....................................................................................................................1-84
PRODUCT DESIGN AND DEVELOPMENT...................................................................................... 1-84
ADDITIONAL DESIGN ...................................................................................................................... 1-84
FACTORY DEFAULT SOUND DESIGN ............................................................................................ 1-84
III of VI
USER’S MANUAL .............................................................................................................................. 1-84
CONTACT INFORMATION......................................................................................... 1-84
ELEKTRON SUPPORT ..................................................................................................................... 1-84
ELEKTRON WEBSITE ...................................................................................................................... 1-84
DELIVERY ADDRESS ....................................................................................................................... 1-84
APPENDIX A: MACHINE REFERENCE
TRX......................................................................................................................................................A-1
BASS DRUM “TRX-BD”..................................................................................................................A-1
BASS DRUM “TRX-B2” ..................................................................................................................A-1
SNARE DRUM “TRX-SD” ...............................................................................................................A-1
TOM “TRX-XT”................................................................................................................................A-2
CLAP “TRX-CP”..............................................................................................................................A-2
RIM SHOT “TRX-RS”......................................................................................................................A-2
COW BELL “TRX-CB”.....................................................................................................................A-2
CLOSED HIHAT “TRX-CH”.............................................................................................................A-2
OPEN HIHAT “TRX-OH” .................................................................................................................A-2
CYMBAL “TRX-CY” ........................................................................................................................A-2
MARACAS “TRX-MA” .....................................................................................................................A-2
CLAVES “TRX-CL”..........................................................................................................................A-3
CONGAS “TRX-XC”........................................................................................................................A-3
EFM .....................................................................................................................................................A-4
BASS DRUM “EFM-BD” .................................................................................................................A-4
SNARE DRUM “EFM-SD”...............................................................................................................A-4
TOM “EFM-XT” ...............................................................................................................................A-4
CLAP “EFM-CP” .............................................................................................................................A-4
RIMSHOT “EFM-RS” ......................................................................................................................A-4
COWBELL “EFM-CB” .....................................................................................................................A-4
HIHAT “EFM-HH” ............................................................................................................................A-5
CYMBAL “EFM-CY” ........................................................................................................................A-5
E12.......................................................................................................................................................A-6
BASS DRUM “E12-BD”...................................................................................................................A-6
SNARE DRUM “E12-SD”................................................................................................................A-6
HIGH TOM “E12-HT” ......................................................................................................................A-6
LOW TOM “E12-LT” ........................................................................................................................A-6
CLAP “E12-CP”...............................................................................................................................A-6
RIMSHOT “E12-RS” .......................................................................................................................A-6
COW BELL “E12-CB” .....................................................................................................................A-7
CLOSED HIHAT “E12-CH” .............................................................................................................A-7
OPEN HIHAT “E12-OH”..................................................................................................................A-7
RIDE CYMBAL “E12-RC” ...............................................................................................................A-7
CRASH CYMBAL “E12-CC” ...........................................................................................................A-7
BRUSHED SNARE “E12-BR” .........................................................................................................A-7
TAMBOURINE “E12-TA” .................................................................................................................A-8
TRIANGLE “E12-TR” ......................................................................................................................A-8
SHAKER “E12-SH” .........................................................................................................................A-8
BONGO CONGO “E12-BC” ............................................................................................................A-8
P-I ........................................................................................................................................................A-9
BASS DRUM “PI-BD”......................................................................................................................A-9
SNARE DRUM “PI-SD”...................................................................................................................A-9
TOM “PI-XT” ...................................................................................................................................A-9
RIMSHOT “PI-RS” ..........................................................................................................................A-9
METALLICA “PI-ML” .......................................................................................................................A-9
MARACAS “PI-MA”.........................................................................................................................A-9
IV of VI
HI HAT “PI-HH” ...............................................................................................................................A-9
RIDE CYMBAL “PI-RC” ................................................................................................................A-10
CRASH CYMBAL “PI-CC” ............................................................................................................A-10
GND ................................................................................................................................................... A-11
SINUS “GND-SN” ......................................................................................................................... A-11
NOISE “GND-NS” ......................................................................................................................... A-11
IMPULSE “GND-IM” ..................................................................................................................... A-11
INP ..................................................................................................................................................... A-11
INPUT GATE A/B “INP-GA/B” ...................................................................................................... A-11
INPUT FILTER FOLLOWER A/B “INP-FA/B” ............................................................................... A-11
INPUT ENVELOPE A/B “INP-EA/B” ............................................................................................. A-11
MID ....................................................................................................................................................A-12
CTR ...................................................................................................................................................A-12
CONTROL ALL “CTR-AL” ............................................................................................................A-12
CONTROL 8 PARAMETERS “CTR-8P” .......................................................................................A-13
CONTROL RHYTHM ECHO DELAY “CTR-RE” ...........................................................................A-13
CONTROL GATE BOX REVERB “CTR-GB” ................................................................................A-14
CONTROL MASTER EQ “CTR-EQ”.............................................................................................A-14
CONTROL DYNAMIX PROCESSOR “CTR-DX”..........................................................................A-14
ROM (SPS-1UW ONLY) ....................................................................................................................A-15
ROM MACHINES “ROM-1 - ROM-48”..........................................................................................A-15
RAM (SPS-1UW MKII ONLY) ............................................................................................................A-15
RAM RECORD “RAM-R1 - RAM-R4” ...........................................................................................A-15
RAM PLAY “RAM-P1 - RAM-P4” ..................................................................................................A-16
RAM MACHINES TUTORIAL .......................................................................................................A-16
APPENDIX B:
MIDI CONTROL REFERENCE
DEFAULT MIDI MAPPINGS ...........................................................................................................B-1
CTRL-CHANGE MAPPINGS..........................................................................................................B-1
APPENDIX C:
INDEX
SYSEX REFERENCE
V of VI
VI of VI
INTRODUCTION
INTRODUCTION
Thank you for choosing the Machinedrum SPS-1 MKII/SPS-1UW MKII, Synthetic Percussion Sequencer. The Machinedrum is a powerful and intuitive tool for creating percussion
sounds and rhythm sequences. The Elektron development team would like to take this
opportunity to thank you for your choice of music creation tool. We hope that you will have
a lot of fun while exploring the vast possibilities of the Machinedrum. To make the most of
the SPS-1 MKII/SPS-1UW MKII, we would recommend you to carefully read the relevant
parts of this manual.
This manual is specifically written for the MKII versions of the Machinedrum family. However, although differences exist between the MKI and MKII models, this manual it is also
usable for MKI models. Please see “DIFFERENCES BETWEEN THE MKI AND MKII
MODELS” on page 83 for more details on exactly what differs between the two models.
CONVENTIONS IN THIS MANUAL
In this manual, we have used certain conventions to indicate input operations using knobs
and buttons and output from the user interface. These conventions are listed below:
Buttons are written in upper case with bold style, and they are enclosed in brackets. For
instance, the button “function” on the main panel is written [FUNCTION].
Menu names, certain modes and operations will be written in upper case. The SYNTHESIS
menu is an example of that.
Messages visible on the screen will be written in upper case with quotation marks. Like
this, “RECEIVING DUMP”.
Parameter abbreviations as they appear on the screen are written in bold style, for example PTCH.
Knobs are written in upper case with bold, italic style. For instance, the knob “level” is written LEVEL.
LED indicators like the record light are written <RECORD>.
The following symbols are used throughout the manual:
This symbol indicates information that you need to pay attention to.
This symbol indicates a tip that might make it easier interacting with the Machinedrum.
This symbol is not used, but it shows a nice ear.
1
THE STORY OF THE MACHINEDRUM
THE STORY OF THE MACHINEDRUM
The Machinedrum SPS-1 MKII/SPS-1UW MKII is a music instrument that presents new
methods for music synthesis and creation. It also traces its heritage to classic drum
machines.
The drum machine concept is more than 30 years old. Around the same time that Bob
Moog released his first commercial synthesizer for keyboard players, the first consumer
drum machines were also made available. Although primitive in design with only pre-programmed patterns to offer, they laid the foundation for a new area of electronically aided
music and sound creation.
What followed has formed a good part of the percussive basis for modern music. The drum
machines from Roland (the TR-series), Linn and Simmons are legendary and highly
regarded for their individual synthetic sound. The analogue drum machines were actually
advanced synthesizers, specially designed for creating a specific percussive sound. Today
respect is gained not by recreating the sound of an acoustic drum, but by adding to the
tonal palette of percussion. The method of “grid programming” has also offered a creative
approach to forming rhythms.
Percussion synthesis was a neglected area for many years. Straight static samples can
never replace the full possibilities of a powerful drum synthesizer / sequencer. With the
Machinedrum, we have incorporated the best ideas from the classic drum machines, using
specially designed “machines” for many types of percussion, combined with new rhythm
composing possibilities to make the SPS-1 MKII/SPS-1UW MKII the state of the art drum
synthesizer and sequencer.
For the sample enabled Machinedrum, the Machinedrum SPS-1UW MKII, where “UW” is
short for “UserWave”, inspiration was drawn from the 12-bit samplers of the 1980’s, for
example the EMU SP-1200. The sound from these instruments were often very characteristic and had a punch and grit that can be hard to obtain today. Combining samples with the
ease of use and flexibility that the Machinedrum environment offers will vastly expand the
sound shaping possibilities.
Not only getting inspiration from the past, the concept of the SPS-1UW MKII also makes it
possible to explore new sonic territories as it contains real time sampling features. All this
makes the Machinedrum UserWave an ideal companion for both forward-thinking DJ’s and
beat composers looking for a unique sound.
MACHINEDRUM SPS-1 MKII/SPS-1UW MKII MAIN FEATURES
The SPS-1 MKII/SPS-1UW MKII is built from three parts - the percussion synthesizer, the
effect system and the percussion sequencer.
The synthesizer holds 16 drum generating synthesizers - machines - simultaneously. Each
of the machines is designed for creating a specific drum sound, such as bass drum or
claves, from a set of parameters. The machines can belong to a varied set of MD-synths,
where every MD-synth have a different sound character.
The effect system consists of the TRACK EFFECT system and the STEREO MASTER
EFFECT System. The TRACK EFFECT system supplies Amplitude Modulation, 1-band
EQ, Resonant lo/band/hi-pass filter, Sample Rate Reduction and Distortion tied to each
2
THE STORY OF THE MACHINEDRUM
audio track. These effects can be used tightly together with the machines to form the
sound.
The STEREO MASTER EFFECT system consists of a delay, a reverb, an EQ and a
dynamics compressor. These effects operate on the mixed main output signal.
• SPS-1 MKII/SPS-1UW MKII features the MD-synths TRX, EFM, E12, PI and GND
that generate percussive sounds from different theories and practices. The SPS1UW MKII adds the sample handling ROM and RAM machines.
• The MD-synths offer specialised machines. Each machine is designed for creating
a specific drum sound, such as bass drum or claves.
• A wide variety of special machines are available. These allow creative usage of
the external inputs and extensive control options.
• The machines are arranged in kits together with settings for the track and master
effects, giving a total of 16 fully user controlled real time synthesized percussion
sounds.
• Each machine has up to eight parameters, which can be tweaked in real time by
the user.
• A machine used in a kit is assigned to one of the 16 tracks controlled by the
sequencer.
• Each track has its own track effect, consisting of amplitude Modulation, 1-band
EQ, resonant lo/band/hi-pass filter, sample rate reduction and distortion.
• The sequencer has full control over the machines, as well as the Track Effects.
• The STEREO MASTER EFFECT system consists of the RHYTHM ECHO, the GATE
BOX REVERB, the MASTER EQ and the DYNAMIX compressor. Each track has
separate send routing for the RHYTHM ECHO and the GATE BOX reverb.
• In addition to the MD-synths, the SPS-1 MKII/SPS-1UW MKII can also function as a
very competent MIDI sequencer by using machines especially designed for controlling external MIDI instruments.
• The SPS-1UW MKII can contain up to 2,5 MB of samples, divided into 48 sample
slots.
Machinedrum SPS-1/SPS-1 UW/SPS-1 MKII/SPS-1UW MKII USER’S MANUAL for operating system version
1.53. This manual (rev J) is copyright © 2001-2010 Elektron Music Machines MAV AB. All reproduction without
written authorization is strictly prohibited. The information in this manual may change without notice. Elektron’s
product names, logotypes, titles, words or phrases may be registered and protected by Swedish and international
law. All other brand or product names are trademarks or registered trademarks of their respective holders.
3
USER INTERFACE AND CONNECTORS
USER INTERFACE AND CONNECTORS
FRONT PANEL
&&
'
&*
&
(
&,
)
*
&-
+
''
,"&%
GLOBAL
SONG SETUP
'(
1/64
1:4
2:4
3:4
4:4
')
'*
3
HT
4
MT
5
LT
6
CP
7
RS
8
&'"&(
CB
9
CH
&)
10
OH
11
RC
12
CC
13
M1
14
M2
15
M3
16
M4
&."'&
The Machinedrum SPS-1 MKII/SPS-1UW MKII front panel:
1. Master volume control. Sets the volume for the main output and headphone jack.
2. The <SOUND SELECTION> LEDs. Used for indicating the current track in focus and for
showing which tracks are triggered.
3. [CLASSIC/EXTENDED] mode change key. Changes current editing mode between
CLASSIC and EXTENDED.
4. SOUND SELECTION wheel. Selects tracks and changes values during editing. You can
also select tracks by holding the [FUNCTION] key while pressing the corresponding
[TRIG] key.
5. [FUNCTION] key. Press and hold it for accessing the secondary function of another key.
6. [BANK] key. Used for switching between bank group A to D and E to H.
7. [A/E] key. Hold this key while pressing one of the [TRIG] keys to select a pattern in
either the A or the E bank, depending on which bank group is selected. The secondary
function is track muting.
8. [B/F] key. Hold this key while pressing one of the [TRIG] keys to select a pattern in
either the B or the F bank, depending on which bank group is selected. The secondary
function is accent pattern editing.
9. [C/G] key. Hold this key while pressing one of the [TRIG] keys to select a pattern in
either the C or the G bank, depending on which bank group is selected. The secondary
function is the pattern swing settings.
10.[D/H] key. Hold this key while pressing one of the [TRIG] keys to select a pattern in
either the D or the H bank, depending on which bank group is selected. The secondary
function is slide pattern editing.
11.The LCD graphical interface.
12.[ENTER/YES] key. Used for entering sub-menus and for confirming choices.
4
USER INTERFACE AND CONNECTORS
13.[EXIT/NO] key. Used for exiting the current menu and for deselecting options.
14.The arrow keys. Used for menu navigation. They are called [UP], [DOWN], [LEFT] and
[RIGHT].
15.LEVEL knob. Sets the overall volume level of the track in focus.
16.[TEMPO] key. Brings up the tempo menu. The current tempo is always indicated by the
speed the <TEMPO> LED is flashing.
17.DATA ENTRY knobs. Used for tweaking parameters for the machines and effects.
18.[SYNTHESIS/EFFECTS/ROUTING] toggle key. Switches the editing focus for the
DATA ENTRY knobs. The active page is indicated by the <SYNTHESIS>, <EFFECTS>
and <ROUTING> LEDs. The secondary function is calling the LFO edit menu.
19.[RECORD] key. Toggles grid edit mode on/off. Starts live recording if held while pressing
[PLAY]. In GRID RECORDING mode, the <RECORD> LED gives a steady light, while
in live recording it flashes. The secondary function is COPY.
20.[PLAY] key. Initiates playback of a pattern or song. Pressing [PLAY] a second time
pauses playback. The secondary function is the CLEAR operation.
21.[STOP] key. Stops the playback of a pattern or song. The secondary function is PASTE.
• The copy, clear and paste functions are tied to different data depending on the
context where they are used. Their use will be described in their respective parts
of this manual.
22.[PATTERN/SONG] key. Switches between pattern and song sequencer mode. The cur-
rent sequencer mode is indicated by the <PATTERN> and <SONG> LEDs. The secondary function is calling the GLOBAL EDIT menu.
23.[KIT] key. Opens the KIT menu. The secondary function is opening the SONG menu.
24.[TRIG] keys 1 to 16. Used for direct trigging of machine per track, and for placing notes
in th GRID RECORDING and LIVE RECORDING modes. Also used for choosing pattern, if pressed while holding [A-H] keys. They are also used for selecting track when
pressed while holding [FUNCTION]. Above each [TRIG] key is a <TRIG> LED.
25.[SCALE SETUP] key. Switches the editing focus of the [TRIG] keys between the differ-
ent pattern pages, if the scale length is longer than 16 steps. Above the [SCALE
SETUP] key the four <PATTERN PAGE> LEDs are placed. If for example 64 steps is
used in a pattern, all four LEDs will be lit. The LEDs are used for indicating which page
of the pattern currently being played or edited. Note that MKI units can have a maximum of 32 steps per pattern.
For scale lengths up to 16 steps, the <1:4> LED will stay lit and pressing [SCALE
SETUP] will have no effect. The secondary function of the [SCALE SETUP] key is
calling the SCALE SETUP menu.
5
USER INTERFACE AND CONNECTORS
REAR CONNECTORS
HEH"&$HEH"&JL
&
'
("*
+",
-"&&
&'"&(
&)
("*
+",
-"&&
&'"&(
&)
HEH"&B@>>$HEH"&JLB@>>
&
'
The Machinedrum SPS-1 MKII/SPS-1UW MKII rear connectors:
1.
Power on/off switch.
2.
6V DC power in.
• Caution! Use only an Elektron-approved power supply with your Machinedrum
SPS-1 MKII/SPS-1UW MKII. A power supply is included with all MKII models. It
can be used all over the globe without the need of voltage converters using an
appropriate power cord. Using the wrong type of adapter may damage your unit.
Damage caused by the use of incorrect power supply is not covered by warranty.
Please see “TECHNICAL INFORMATION” on page 82 for details about the MKII
power supply.
6
•
Note that the MKI models require a different power supply compared to the MKII
models. Please see “DIFFERENCES BETWEEN THE MKI AND MKII MODELS” on
page 83 for details about the power supply to be used with the MKI models.
3.
MIDI Thru.
4.
MIDI Out.
5.
MIDI In.
6.
Input B.
USER INTERFACE AND CONNECTORS
7.
Input A.
8.
Individual output F.
9.
Individual output E.
10. Individual output D.
11. Individual output C.
12. Main out right / Individual output B.
13. Main out left / Individual output A.
14. Stereo headphones output.
RACK MOUNT KIT (ACCESSORY)
The Machinedrum SPS-1 MKII/SPS-1UW MKII can be rack mounted in a standard 19”
rack, using the Machinedrum rack mount kit which is ordered separately. When rack
mounted, the unit occupies four standard height units plus whatever additional space is
needed to accommodate cables plugged into the unit at the back.
RACK MOUNT KIT ASSEMBLY
Make sure that you have a Philips screwdriver which is in good condition, and which is the
right size. Use the included M3x6mm size screws to secure the rack mount consoles on
each side of the Machinedrum. Make sure that all screws are fastened for secure operation
of the unit.
CONNECTING THE UNIT
Before you start connecting the Machinedrum to other units, make sure that everything is
switched off.
1. Insert the supplied DC adapter into the wall socket, and connect the small plug into the
rear of the Machinedrum unit.
2. Connect the main out L/R from the Machinedrum to your mixer or amplifier.
3. If MIDI control is desired, connect MIDI OUT from the Machinedrum to the device that
you wish to send data to. Connect the MIDI IN to the device that you wish to receive data
from. The MIDI THRU port “echoes” the data arriving at the MIDI IN port, so it can be
used for chaining MIDI units together.
4. Switch on all units.
CARE INSTRUCTIONS
To ensure many years of trouble free operation, please follow the advice below:
• Never use any aggressive cleaners on the casing or the LCD overlay. Remove
dust, dirt and fingerprints with a soft dry cloth. More persistent dirt can be
removed with a slightly damp cloth using only water.
• Never use sharp objects near the display to avoid scratches or damage. Also
avoid applying any pressure to the display itself.
• When transporting the Machinedrum, try to use the box and padding the Machinedrum originally shipped with, or comparable packaging.
• Make sure that you place the unit on a stable surface before use. If you mount the
unit in a rack, be sure to tighten all four screws in the rack mount holes.
• The memory used for storing patches and kits is powered by a battery inside the
unit. It will hold data at least 6 years before needing replacement. If the battery
7
USER INTERFACE AND CONNECTORS
needs replacement, the “BATTERY LOW” message will appear in the display. Contact Elektron support or your nearest repair center.
• Turn off the machine when it is not in use.
8
THE LCD USER INTERFACE
THE LCD USER INTERFACE
The center of Machinedrum SPS-1 MKII/SPS-1UW MKII editing is the LCD display. The
main interface screen is shown below:
1. The current tempo displayed with one decimal.
2. Four boxes showing the playback position in the pattern page.
3. The playback/recording status shown by the standard “record”, “play”, “pause” and
“stop” symbols;
,
,
and
.
4. Name and number of the current kit.
5. Specification of the MD-synth, machine and current data entry focus.
6. Level bar showing the overall volume level of the machine on the active track.
7. Up to eight control data entry values. They show what the DATA ENTRY knobs control
and also indicate the current data entry values. When two parameters depend on each
other in some way, they will have a small “clip” between them as shown below:
LAYER EDIT AND WINDOWS
When a function which puts a window on top of the main interface screen is opened, the
function of certain buttons and/or knobs will change. The buttons that are not used or
blocked can still be used to control the layer underneath. For example, when you have
called the tempo function it will make use of the SOUND SELECTION wheel, but you can
still use the DATA ENTRY knobs to control the track in focus. When a window has functions mapped to such interface controls, help is provided at the bottom of the window in the
form of icons representing these controls. The icons are:
The arrow buttons
The [FUNCTION] key
The SOUND SELECTION wheel
The [TRIG] keys
• All windows can be closed using the [EXIT/NO] key.
9
QUICK START
QUICK START
This quick start will guide you through some of the basic operations to allow you to start
using the SPS-1 MKII/SPS-1UW MKII right away. First connect it as described in section
“CONNECTING THE UNIT”, on page 7.
PLAYING AND TWEAKING DRUM SOUNDS
1. Press the [KIT] key.
2. Select the LOAD KIT icon in the menu and press [ENTER/YES]. You will now be pre-
sented with a list where you can select a kit name using the [UP] and [DOWN] keys.
3. Press [ENTER/YES] to load the kit. Exit the menu by pressing [EXIT/NO]
4. Now press any of the 16 [TRIG] keys to play the corresponding drum assigned to that
track. You will notice that the drum select LEDs in the upper left corner will light up
accordingly.
5. Turn the SOUND SELECTION wheel so that the <BD> LED is lit. <BD> is now the
“active track”, and every parameter that is being edited will be directed to the bass drum
track.
6. Make sure that the <SYNTHESIS> LED is lit by pressing the toggle key [SYNTHESIS/
EFFECTS/ROUTING].
7. Now, turn any of the DATA ENTRY knobs to tweak the corresponding bass drum
machine specific parameter. You can trigger the sound by pressing the first [TRIG] key
while you are turning the DATA ENTRY knob A to hear the pitch change.
• Instead of using the SOUND SELECTION wheel to choose the active track you can
hold the [FUNCTION] key while pressing the corresponding [TRIG] key.
• The DATA ENTRY knobs have accelerated editing when pressed. By default, the
knobs increase/decrease in steps of +1/-1. When pressed, the step length is
higher, allowing quicker adjustments.
USING THE TRACK EFFECTS
1. Press the [SYNTHESIS/EFFECTS/ROUTING] key until the <EFFECTS> LED is lit.
2. You can now edit the track effect parameters for the active track by turning the DATA
ENTRY knobs.
SELECTING AND PLAYING A PATTERN
1. Make sure you have loaded a kit. See the previous section for details on this.
2. Press the [CLASSIC/EXTENDED] key until the <CLASSIC> LED is lit. You are now in
CLASSIC mode. The difference between CLASSIC and EXTENDED mode is explained
in more detail on page 35.
3. Check the [PATTERN/SONG] key so that the <PATTERN> LED is lit.
4. Press the [BANK GROUP] key to select between banks A to D or E to H. Select pattern
bank A to D for this demonstration.
10
QUICK START
5. To select pattern A01, press and hold the pattern selection key [A/E] and then the
[TRIG] key 1. You can see the currently selected pattern in the lower left corner of the
display.
6. To play this pattern, simply press the [PLAY] key. The pattern will start playing and will
loop once it reaches the end. Pressing the [PLAY] key while playing pauses the playback. Holding the [STOP] key and pressing [PLAY] will immediately restart the playback
from the beginning. The amount of <SCALE> LEDs lit indicated the number of pages the
pattern consists of. For example, if two <SCALE> LEDs are lit, then the pattern consists
of two pages.
7. To change pattern during playback, simply select a pattern the same way as in step 4.
The display will show the selected pattern beside the current one, but with an arrow
pointing towards it. This indicates that once the current pattern has come to its end, the
selected pattern will begin to play.
8. To stop the playback of the pattern, press the [STOP] key.
• There might be occasions when the Machinedrum keeps making noise after you
press the [STOP] button. This situation can especially occur when using samples
with an infinite decay in the Machinedrum UserWave. In order to force all the
tracks to go quiet, quickly press the [STOP] button twice.
• The pattern page currently playing is indicated by the flashing of the <PATTERN
PAGE> LED.
RECORDING A PATTERN USING GRID RECORDING
1. You can input notes into a pattern in the sequencer, both while it is playing or while it is
currently stopped. Press the [RECORD] key to start grid recording. The <RECORD>
LED will be lit the whole time during the process.
2. Select the active track using the SOUND SELECTION wheel.
3. Press the [TRIG] keys to insert 16th notes where you wish to have the machine trig-
gered. Pressing the same [TRIG] key once more removes the note.
4. To edit other tracks, change the active track using the SOUND SELECTION wheel.
SETTING THE ACCENT PATTERN
1. Hold [FUNCTION] and press key [B/F] to access the ACCENT screen.
2. On this screen you can set the accent level for all of the accent trigs. Use the SOUND
SELECTION wheel to set the level.
3. The accent pattern is shown on all <TRIG> LEDs above the [TRIG] keys as long as you
are in the accent screen. To accent a note, simply select it by pressing the [TRIG] key.
To remove the accent, press the same key again.
SETTING THE SWING PATTERN
1. Hold [FUNCTION] and press key [C/G] to access the swing screen.
2. On this screen you can set the amount of swing on notes selected by the swing pattern.
Use the SOUND SELECTION wheel to set the level. A level of approximately 65%
should allow you to hear the effect.
3. The swing pattern is shown on all <TRIG> LEDs above the [TRIG] keys as long as the
swing screen is active. The default swing pattern affects every other note, starting with
11
QUICK START
the second. The swing pattern can be changed using the [TRIG] keys, but for normal
rhythm styles the default pattern is better left as it is.
PATTERN LIVE RECORDING
1. The LIVE RECORDING mode of a pattern allows you to play the sounds in the kit while
the pattern is playing. To start this mode, hold [RECORD] and then press [PLAY].
2. You can now “play” all the machines in the kit directly on the [TRIG] keys. All played
notes will be quantised to 16th notes, and you will be able to hear them the next time the
pattern starts all over.
3. The pattern will loop until you press the [STOP] key.
PARAMETER LOCKS
1. Press the [CLASSIC/EXTENDED] key until the <EXTENDED> LED is lit. You are now in
extended mode. The difference between CLASSSIC and EXTENDED mode will be
explained on page 35.
2. Now it is possible to lock parameters to a specific note in the pattern. In GRID RECORD-
ING mode, hold a [TRIG] key and then tweak a parameter. The parameter adjusted will
be inverted on the LCD screen to indicate that it now is locked to the value you have set.
The corresponding <TRIG> LED will flash rapidly to indicate that a parameter is locked
for that step.
3. In LIVE RECORDING mode, you can lock parameters by tweaking the knobs while
recording.
4. Parameters can be locked for several tracks simultaneously. To lock parameters for a
new track, just repeat the sequence from step 2 above.
5. To remove a lock, enter grid edit mode and press the [TRIG] key on the locked note
twice. This removes the lock and restores the note to be triggered. You can also hold the
[TRIG] key while clicking the DATA ENTRY knob corresponding to locked parameter.
You will see that the inversion disappears and that the parameter lock is removed.
12
THE SOUND SYNTHESIS OF MACHINEDRUM
THE SOUND SYNTHESIS OF MACHINEDRUM
Track 01
Accent Swing
MIDI OUT
Parameter Locks
& Slides
MD Pattern Sequencer
Step Seq
Track 16
MIDI IN
LFO 1
LFO 16
Track FX
Synthesis
MD Machine
Synthesis
Routing
OUT A—F
OUT A—F
Stereo Master Effects System
Rhythm Echo
Dynamix
EQ
MAIN MIX
Gate Box
The basic sound generating unit in the Machinedrum is called a machine. Each machine is
designed for generating a specific drum sound such as bass drum, snare or claves. However, this does not mean that you only have to use it for generating the sound indicated by
its name. The flexible synthesis and effects system can transform a sound completely,
allowing you to come up with unique percussion sounds.
The machines are grouped in MD-synths. You could see it as if the machines in an MDsynth belong to the same family. In the EFM family for example, there are a total of 8
machines for bass drum, snare drum, closed hi-hat etc. Despite the fact that each machine
is based on the family synthesis, each machine has a unique synthesis parameter set. The
parameters have been carefully selected to give you the best sound shaping possibilities
for that particular machine.
The MD-synths and their machines are covered in “Appendix A: MACHINE REFERENCE“.
Each of the 16 tracks can have any machine assigned to it. The assignment of machines
and their parameter settings are collected in so called “kits”. Editing the kits is discussed in
section “KIT ASSEMBLY”, on page 17.
13
THE SOUND SYNTHESIS OF MACHINEDRUM
Every track has its own dedicated effect module, called the TRACK EFFECT system. Each
track effect delivers hi/lo/band-pass resonant 24dB filter, amplitude modulation, 1-band eq
and sample rate reduction. The settings of effects are saved in the kit as well. The TRACK
EFFECT system is explained in section “THE TRACK EFFECTS”, on page 22.
The ROUTING page controls pan, delay send, reverb send, output distortion and volume.
The routing options are discussed in section “THE ROUTING PAGE”, on page 25.
The SPS-1 MKII/SPS-1UW MKII offers 16 assignable Low Frequency Oscillators (LFO’s)
that you can connect to any synthesis parameter, track effect or routing parameter. More
about the LFO’s can be found in section “LOW FREQUENCY OSCILLATORS (LFO’s)”, on
page 32.
The STEREO MASTER EFFECT system containing delay, reverb, EQ and compression
add further to the sound shaping possibilities of the Machinedrum. Read more about the
“THE STEREO MASTER EFFECT SYSTEM” on page 28.
MACHINEDRUM KITS
Machinedrum kits hold the information specified below:
•
•
•
•
•
•
The machine selected for each of the 16 tracks
Parameter settings for the 16 machines
Parameter settings for the TRACK EFFECT system
Parameter settings for routings to the STEREO MASTER EFFECT system.
Parameter settings for the STEREO MASTER EFFECT system
The kit name
All kits are battery backed and user definable. A total of 64 user kits can be stored in memory. When in EXTENDED mode, kits are connected to patterns. Selecting a new pattern will
then automatically load the associated kit. In CLASSIC mode, kits and patterns are not
linked. Read more about this in the chapter “CLASSIC VS EXTENDED” on page 35.
• You can either assemble a kit from scratch or modify an existing one and then
save it to a new position. Building your kit from an existing one is often quicker.
LOADING A KIT
1. Open the KIT window by pressing the [KIT] key
2. Use the arrow keys to move to the LOAD icon. Press [ENTER/YES] to open the LOAD
KIT menu.
14
THE SOUND SYNTHESIS OF MACHINEDRUM
3. The screen presents a list of the kits stored in memory. Use the [UP] and [DOWN] keys
to choose among the 64 kit slots. Press [ENTER/YES] to load the kit of your choice.
If you want to exit without loading a kit, press [EXIT/NO].
• Kits that are not associated with any pattern are distinguished by a little star after
the kit name.
SAVING AND NAMING A KIT
1. Open the KIT window by pressing the [KIT] key.
2. Use the arrow keys to move to the SAVE icon. Press [ENTER/YES] to open the SAVE
KIT menu.
3. The screen presents a list of the kits stored in memory. Use the [UP] and [DOWN] keys
to choose among the 64 kit slots. Press [ENTER/YES] to select the slot where you want
to save your kit.
4. The window opening will allow you to name the kit:
15
THE SOUND SYNTHESIS OF MACHINEDRUM
Use the SOUND SELECTION wheel or the [UP] and [DOWN] keys to cycle through the
letters. The [LEFT] and [RIGHT] keys move the cursor backwards and forwards on the
line.
5. Pressing the [FUNCTION] key gives access to the “high score” selection method, in
which you see all characters at the same time. Keep the [FUNCTION] key held while
navigating using the [LEFT], [RIGHT], [UP] and [DOWN] buttons. Release the [FUNCTION] key, when you have found the right letter.
6. When the kit naming procedure is completed, press [ENTER/YES] to save it.
7. If you want to exit without saving the kit, press [EXIT/NO].
UNDO KIT
There is a special kit in the first position of the kit list called the “UNDO KIT”.
When you have made unsaved changes to a kit and a new one is loaded, the unsaved old
kit will be stored in the UNDO KIT position. When saving a kit over an occupied position in
the kit list, the overwritten kit will also be saved in the UNDO KIT.
You can load the UNDO KIT to restore your most recent unintentionally lost kit. This can
often be useful in EXTENDED mode, where a pattern change automatically can change
kits. When you have needed to restore your kit using the UNDO kit, don’t forget to save it.
COPY KIT
When in the SAVE KIT or LOAD KIT menus you can copy and paste kits.
When you are in either the SAVE KIT or LOAD KIT menus, select the kit you want to copy,
hold down the [FUNCTION] key and press the [RECORD] button. A message saying
“COPY KIT” appears.
8. Use the [UP] and [DOWN] keys to scroll to the slot you want to copy the kit to.
16
THE SOUND SYNTHESIS OF MACHINEDRUM
9. To paste the kit into the slot, hold [FUNCTION] and press the [STOP] button. The mes-
sage “PASTE KIT” appears.
• If you want to undo the action, press the [FUNCTION] + [STOP] buttons again. The
message saying “UNDO KIT” indicates that the paste operation has been undone.
CLEAR KIT
You can also clear kits while in the SAVE or LOAD KIT menus.
1. Select the kit you want to clear, hold down the [FUNCTION] key and press the [PLAY]
button. A message saying “CLEAR KIT” appears.
• It is also possible to undo this operation. To undo the action, hold the function
[FUNCTION] button and press the [PLAY] button. The message saying “UNDO
KIT” indicates that the clear operation has been undone.
KIT ASSEMBLY
To assemble a kit, you need to select and assign your machines for each track. First open
the KIT window by pressing the [KIT] key.
1. Use the arrow keys to move to the EDIT icon. Press [ENTER/YES] to open the edit win-
dow.
2. The EDIT KIT menu is used for both selecting which machine to load to a track and for
specifying mute and trig groups. The <SOUND SELECTION> LEDs indicate which track
you are editing, also shown at the top of the EDIT KIT window. To change track position,
turn the SOUND SELECTION wheel left or right, or hold down the [FUNCTION] key and
press the corresponding [TRIG] key.
17
THE SOUND SYNTHESIS OF MACHINEDRUM
3. After choosing what track you want to change, use [LEFT] and [RIGHT] to choose
between the SYNTH, MACHINE and RELATE columns. [LEFT] and [RIGHT] are also
used for selecting MUTE/TRIG POS focus in the RELATE column. Once you have
entered a column, it will be highlighted and now you can use [UP] and [DOWN] to
choose from the available options.
Select the MD-synth by first selecting the SYNTH column with the [LEFT] and [RIGHT]
keys. Then move the focus using [UP] and [DOWN] to select the MD-synth of your
choice.
4. When you are satisfied with your choice, press [RIGHT] once to move the focus to the
MACHINE column. Select the machine using [UP] and [DOWN].
5. Finally you need to press the [ENTER/YES] key to confirm your selection. This will load
the machine with every value set to default.
• If you want to load a machine and keep the previous settings of the TRACK
EFFECT and ROUTING pages, hold [FUNCTION] while pressing the [ENTER/YES]
key.
• You can preview sounds without loading them. While in the EDIT KIT menu, make
sure that the <RECORD> LED is not lit and that the focus is on the MACHINE column. Then press the [TRIG] key corresponding to the active track. You will now
hear the default sound of the chosen machine.
• The MD-synth and the machine currently selected are shown as inverted text. The
focus, when moved away from the original selection, is a square window. Once
[ENTER/YES] is pressed, the current focus will be selected, thus changing the
focus to inverted text.
SETTING MUTE AND TRIG RELATIONS OF A KIT
Mute groups are useful for interleaving drums such as open and closed hi-hats. Trig groups
can be used for making layered drums, consisting of two drums on different tracks that are
triggered by one drum trig only.
18
THE SOUND SYNTHESIS OF MACHINEDRUM
1. In the EDIT KIT menu, move the focus using the [LEFT] and [RIGHT] keys to the
RELATE column. [LEFT] and [RIGHT] are also used for selecting the MUTE/TRIG POS
focus.
2. The mute relation is used for interleaving drums, such as open and closed hi-hats which
are supposed to stop the sound of each other when played. Use the [UP] and [DOWN]
keys to select which track is muted when the current machine is triggered.
3. The trigger relation is used for layering sounds. It can either be used to make a sound
richer or to combine two entirely different machines to make a new type of percussion.
Use [LEFT] and [RIGHT] to move to the TRIG POS position. Use the [UP] and [DOWN]
keys to select which track will be played in addition to the current when it is trigged. Confirm the selection by pressing the [ENTER/YES] key
• You can not use TRIG relations in a chain. If the bass drum is set to trigger the
snare, and the snare is set to trigger the cymbal, only the bassdrum and snare will
be played when the bass drum is triggered.
• Layering is a very powerful way to expand the sound palette of the SPS-1 MKII/
SPS-1UW MKII. Try using filtering to obtain the low frequency characteristics from
one sound and combine it with the higher frequencies from another. This is especially useful when creating new and interesting bass drum sounds.
COPY MACHINE
You can copy one machine and its settings from one track to another. It is also possible to
copy the current machine and its settings to another kit.
19
THE SOUND SYNTHESIS OF MACHINEDRUM
1. In the edit kit menu, press and hold [FUNCTION] and then press [RECORD]. A mes-
sage saying “COPY MACHINE” appears.
2. The settings are placed in the machine copy buffer. Now you can either change track
using the SOUND SELECTION wheel, or load a new kit and select a target track in
there.
3. Once the target track is selected, press and hold [FUNCTION] and then press [STOP] to
paste the machine settings from the copy buffer. A message saying “PASTE MACHINE”
appears.
• Any previous machine settings will be overwritten when pasting.
• Once the machine is copied into the copy buffer, it can be pasted many times to
several tracks or kits. It will stay in the buffer until it is replaced by a new one.
• The UNDO command is available for this operation. Press the [FUNCTION] +
[STOP] once more to undo the paste operation.
CLEAR MACHINE
It is possible to clear a track, so no machine is connected to it.
1. In the EDIT KIT menu, press and hold [FUNCTION] and then [PLAY] to clear the
machine. A message saying “CLEAR MACHINE appears.
2. A track that you have used the clear machine function on will be displayed like this:
20
THE SOUND SYNTHESIS OF MACHINEDRUM
• The clear machine operation can be undone by performing the operation one
more time. The message “UNDO MACHINE” will be shown in the display.
MACHINE PARAMETER EDITING
Machines are controlled by up to eight synthesis parameters that are accessed with the
DATA ENTRY knobs.
Press the [SYNTHESIS/EFFECTS/ROUTING] key until the <SYNTHESIS> LED is lit. The
rightmost text of the machine information area at the bottom left will show “SYNT” for synthesis. The machine parameters are now controlled by the DATA ENTRY knobs.
• Changes are not stored to the kit unless it is saved. Please see section “SAVING
AND NAMING A KIT”, on page 15 for information about saving kits.
For more information on specific parameters of the different machines, please see “Appendix A: MACHINE REFERENCE“.
21
THE TRACK EFFECTS
THE TRACK EFFECTS
The TRACK EFFECT system is available for all 16 tracks as an extension to the machine
percussion synthesis. The track effects consist of individual effects for every track.
The effects that are available for each track are:
•
•
•
•
Amplitude modulator
1-band parametric EQ
Adjustable lo/hi/bandpass Filter
Sample rate reduction
To access the track effects, press the [SYNTHESIS/EFFECTS/ROUTING] key until the
<EFFECTS> LED is lit. The rightmost text of the machine information area at the bottom
left will show “TFX” for effects. The TRACK EFFECT parameters for the active track are
now controlled by the DATA ENTRY knobs.
• The TRACK EFFECT system is a very powerful sound shaping tool. Use it to either
dramatically alter or subtly change the sound of a machine.
AMPLITUDE MODULATOR
The amplitude modulator is essentially a volume control which is controlled by a low frequency oscillator. It is also known as a tremolo. The frequency of the Machinedrum amplitude modulator can be very high, allowing extreme effects.
AMD controls the the modulation depth.
AMF controls the modulation frequency.
22
THE TRACK EFFECTS
TRACK EQ
Using the 1-band parametric EQ, you can boost or reduce a certain frequency band.
EQF controls which center frequency that will be affected by the EQ gain.
EQG controls the EQ gain. If set to a negative value, the volume of the frequency centered
around the EQF parameter will be reduced.
• If you find a bass drum lacking in punch, try adding a little EQ-gain in the lower
frequencies.
FILTER
The TRACK EFFECT system offers a resonant 24dB lo/hi/band-pass filter. The parameters
are untraditional, giving the user control of both the low and high filter cutoffs, as well as a
variable gap bandpass filter.
FLTF controls the base filter cutoff frequency. When the FLTW parameter is set to its highest value, changing the FLTF parameter has the function of a high-pass filter. When the
FLTF parameter is set to zero, the highpass-Q is disabled.
The illustration below shows the function of the filter.
FLTW controls the filter gap width, that is the distance between the highpass and lowpass
cutoff frequencies. When the FLTF is set to its minimum value, changing the FLTW param-
23
THE TRACK EFFECTS
eter has the function of a low-pass filter. When the FLTW parameter is set to its maximum,
the lowpass-Q is disabled.
FLTQ controls the filter quality Q parameter. The Q value controls how much the volume is
boosted around the low pass and high pass filter cut off frequencies.
THE SAMPLE RATE REDUCER
The sample rate reduction reduces the sample rate using sample and hold.
SRR controls the amount of sample rate reduction.
24
THE ROUTING PAGE
THE ROUTING PAGE
The ROUTING page controls routing of the sound through the distortion, volume and pan,
to the effect buses and also basic LFO control.
To access the ROUTING page, press the [SYNTHESIS/EFFECTS/ROUTING] key until the
<ROUTING> LED is lit. The rightmost text of the machine information area at the bottom
left will show “ROUT” for routing. The routing parameters for the active track are now controlled by the DATA ENTRY knobs.
DISTORTION
The distortion is applied after the TRACK EFFECTS but before volume and pan.
The DIST parameter controls the signal overload distortion.
VOLUME
This volume control is separate from the LEV overall gain control. You can control track
volume by parameter locks or by using the LFO system. The ACCENT feature can also be
used to affect volume of a track.
VOL controls the volume of the track
See section “LOW FREQUENCY OSCILLATORS (LFO’s)”, on page 32 for more information on LFO’s.
See section “PARAMETER LOCKS”, on page 12 for more information on parameter locks.
See section “ACCENT TRACK”, on page 45 for more information on the accent feature.
25
THE ROUTING PAGE
• The LEVEL overall gain control can not be locked or controlled by an LFO.
Instead, use the VOL parameter.
PAN
Here you control the stereo pan for the main stereo outputs. The default value is 0, which
places a sound in the center. When a track is assigned to an individual output, the PAN
parameter has no effect.
PAN positions the sound in the stereo field. A value of -64 will pan the sound hard left, a
value of +63 will pan the sound hard right.
• To get a more spacious sound, try to spread out the tracks in the stereo field using
the PAN parameter. Note though that the normal placement of the bass drum is
almost always in the center.
DELAY SEND
This is a send to the RHYTHM ECHO DELAY of the STEREO MASTER EFFECT system.
When a track is assigned to an individual output, no delay will be applied to the sound.
DEL controls the amount of signal that will be sent to the RHYTHM ECHO delay.
See page 29 for more information on the RHYTHM ECHO delay.
REVERB SEND
This is a send to the GATE BOX reverb of the STEREO MASTER EFFECT system. When
a track is assigned to an individual output, no reverb will be applied to the sound.
REV controls how much signal will be sent to the Machinedrum GATE BOX reverb.
See page 30 for more information on the GATE BOX Reverb.
26
THE ROUTING PAGE
LFO CONTROL
These parameters are identical to those found in the LFO menu.
LFOS controls the speed of the LFO
LFOD controls the modulation depth of the LFO
LFOM controls the mix between the two selectable LFO waveforms.
See section “LOW FREQUENCY OSCILLATORS (LFO’s)”, on page 32 for more information about the LFO’s.
27
THE STEREO MASTER EFFECT SYSTEM
THE STEREO MASTER EFFECT SYSTEM
The STEREO MASTER EFFECT system includes the RHYTHM ECHO delay, the GATE
BOX reverb, the MASTER EQ equalizer and the DYNAMIX dynamic processor (compressor).
The MASTER EQ and DYNAMIX processor effect the final stereo main out signal. The
RHYTHM ECHO and GATE BOX reverb can be fed signals from each of the 16 tracks
using the delay and reverb send parameters All master effect settings are saved as a part
of the kit. The MASTER EFFECTS is only available on the main outputs. You can’t use
them on the individual outputs.
• Even though you can’t parameter lock the master effects, you can still control
them using CTRL-machines. For more info about this, please see “Appendix A:
MACHINE REFERENCE“.
To access the STEREO MASTER EFFECT menu, follow the steps below.
1. Press the [KIT] key to open the kit menu.
2. Move to the MASTER FX icon, and press [ENTER/YES] to open the master effect
menu.
3. Use the [LEFT] and [RIGHT] arrow keys to select the effect you wish to edit.
• Since the master effect settings are stored in the kit, it is important to save the kit
if you wish to keep the changes.
28
THE STEREO MASTER EFFECT SYSTEM
THE RHYTHM ECHO DELAY
The RHYTHM ECHO delay is a multi-functional single tap delay with realtime adjustable
delay time. Some of its functionality can resemble tape loops and solid state CCD delays.
The delay time is synced to the tempo setting.
TIME controls the actual delay time. It is relative to the current tempo, and it is measured in
128th notes. For instance, for a two beat delay (8 16th notes) TIME should be set to 64.
MOD controls the delay time modulation depth.
MFRQ controls the delay time modulation frequency.
FB controls the delay feedback amount. The feedback is taken after the filter but before the
out gain control. FB set to central position with filter totally open gives unity feedback.
FILTF is the filter base frequency parameter. Please refer to section “FILTER”, on page 23
for a description of the functionality of the filter.
FILTW is the filter width parameter. Please refer to section “FILTER”, on page 23 for
description of the function.
MONO is the feedback panning control parameter. A low value gives ping pong style delay,
a high value preserves the stereo information, and a central position brings the delay feedback into the central panning position.
LEV is the out gain level control of the RHYTHM ECHO delay.
• Watch out if you are using FB levels greater than 63. The sound level of the
delayed signal will then constantly increase.
• To get a robotic effect on your drum sounds, turn up the delay send parameter
(DEL) for all sounds, set TIME to 1 and turn up FB to 55.
• You can use the RHYTHM ECHO delay to obtain pseudo stereo effects. Turn up the
DEL send of the sound you want to affect and in the RHYTHM ECHO delay menu,
turn TIME to 1, FB to zero and the MONO parameters to zero. Then set the PAN
parameter of the sound to either hard left or hard right.
29
THE STEREO MASTER EFFECT SYSTEM
THE GATE BOX REVERB
The GATE BOX reverb brings HiQ reverb tailored for percussion, with gating possibilities
for extra effects.
DVOL is the delay to reverb level parameter. This parameter allows the output of the
RHYTHM ECHO to be routed into the GATE BOX reverb.
PRED is the pre-delay parameter. The direct and delay signal mix is delayed by an amount
of time to give the impression of the reverbation arriving after the sound.
DEC is the decay time parameter. Decay time is the time it takes for the reverbation to die
out after a sound has ended. The decay parameter has a span of 0.5 to 3 seconds.
DAMP is the damping control parameter. Damping decreases the high frequencies to give
the impression of soft walls.
HP is a high-pass filter, filtering the output from the reverb.
LP is a low-pass filter, filtering the output from the reverb.
GATE sets the gate time. The reverbated signal is gated after this time, if the signal level is
low. The maximal value for this parameter gives infinite time - in other words, the gate is off.
LEV is the output level parameter of the GATE BOX reberb.
• Sometimes a small amount of gated reverb can be used on snare drums to make
them more distinct. If you are looking for the sound popular in the 1980’s, apply a
fairly large amount of gated reverb to the drum sounds.
MASTER EQ
The MASTER EQ equalizer is the final frequency shaping tool. It supplies one low shelf
and one high shelf filter that allow you to boost or reduce the high and low frequencies. It
also brings one parametric equalizer with frequency and Q-control.
LF is the cut/boost frequency parameter of the low shelf filter.
LG is the low shelf gain parameter that controls how much the low frequencies should be
boosted / reduced between -15dB and +15dB.
30
THE STEREO MASTER EFFECT SYSTEM
HF is the cut/boost frequency parameter of the high shelf filter.
HG is the high shelf gain parameter that controls how much the high frequencies should be
boosted / reduced between -15dB and +15dB.
PF is the parametric EQ frequency parameter, that is the center frequency of the parametric EQ band.
PG is the parametric EQ gain parameter. It controls how much the parametric EQ should
boost or reduce between -15dB and +15dB, at the frequency set by the “PF” parameter.
PQ is the parametric EQ Q factor. The Q controls the width of the band that is boosted or
reduced by the parametric EQ. High Q-values give a narrow band.
GAIN is the final out volume control. This parameter allows you to adjust the out volume of
the main stereo out.
THE DYNAMIX DYNAMICS PROCESSOR
The DYNAMIX dynamics processor is specially designed for compressing percussive
sounds.
ATCK controls the attack time, which is the time it takes the volume detector to react to the
Attack part of the sound signal. Long attack times let fast transients through the compressor.
REL controls the release time. This is the time it takes the volume detector to react to the
Release part of the sound signal. A long release time lifts the signal level as a sound
decays, flattening the dynamics.
TRHD sets the threshold level where the signal starts getting compressed (from -48 to
0dB).
RTIO controls the ratio by which the signal is compressed, when the threshold level is
reached. The ratio has a value in the range 1:1 to 1:256.
KNEE controls the soft knee transition. It makes the transition between compressed and
uncompressed signal smoother, by softening the knee. A low value gives a hard knee.
HP is the side chain High pass filter. This parameter highpass filters the sidechain signal of
the Compressor, so that it does not react to bass.
OUTG out gain raises the signal level. This is used to make up for the gain lost in the compressor.
MIX controls the cross mix between the compressed signal and the original signal. A high
value bypasses the DYNAMIX processor.
31
LOW FREQUENCY OSCILLATORS (LFO’s)
LOW FREQUENCY OSCILLATORS (LFO’s)
Each kit in the Machinedrum has 16 assignable low frequency oscillators (LFO), which can
be used to modulate track parameters. The speed of the LFO is synchronized to the global
tempo.
Each of the 16 LFO’s offers two synchronized waveforms. A mix control allows the output
to be set to any mix between the two waveforms. LFO EDIT
To edit an LFO, follow the steps described below.
Press [FUNCTION] and hold it, then press [SYNTHESIS/EFFECTS/ROUTING] to open
the LFO edit window. Use the SOUND SELECTION wheel to select the LFO to edit.
TRACK displays the target track for the chosen LFO. The LFO’s are by default mapped to
control their own tracks, but they can be set to modulate any track, including other LFO’s
for extra complex modulation waveforms.
PARAM selects the parameter you wish the LFO to modulate. All SYNTHESIS, TRACK
EFFECTS and ROUTING parameters are accessible by the LFO. You can modulate
another LFO by targeting the track it is assigned to, and select either its SPEED, DEPTH or
SHMIX parameters with the PARAM control.
SHP1 selects which waveform shape that can be used by the LFO. There are six types of
available LFO waveforms:
•
•
•
•
•
•
Triangle
Saw
Square
Linear decay
Exponential decay
Random
SHP2 offers inverted waveforms of the ones available in SHP1.
UPDTE controls the behaviour of the LFO. If the UPDTE parameter is set to “FREE”, the
LFO will never retrig. It will then continue to run regardless if new notes are trigged. If
UPDTE is set to “TRIG” the LFO is re-started each time the track is triggered. “HOLD” is a
sample and hold function, which freezes the value of the waveform at the time when the
track is triggered. It will remain frozen until trigged again. Note that LFO’s are only ever
restarted by trigging the corresponding track.
SPEED sets the update speed relative to the tempo in 1/128 note steps.
32
LOW FREQUENCY OSCILLATORS (LFO’s)
DEPTH controls how much the LFO will affect the sound.
SHMIX is a balance control. When set to zero the LFO only uses the SHP1 waveform as
modulation. At its maximum, only modulation by the SHP2 waveform is used.
Below is an illustration showing the behaviour of the waveforms of the LFO’s when set to
the different UPDTE options.
• As the LFO settings are stored in the kit, it is important to save the kit if you wish
to keep the changes.
• The SPEED, DEPTH and SHMIX parameters are also available from the ROUTING
page. As the parameters of the ROUTING page can be controlled by parameter
locks and even by other LFO’s, this can be a source for highly advanced LFO setups.
33
LOW FREQUENCY OSCILLATORS (LFO’s)
• If you select the same destination for two different LFO tracks their outputs will be
added, making advanced layered LFO’s possible.
• You can let a number LFO’s control several parameters of a machine. This allows
for percussion sounds that are constantly changing.
• Note that an LFO can modulate another LFO’s parameters as well, as long as the
modulated LFO is on a higher track. The LFO 03 can modulate the parameters of
the LFO 04, but not vice versa.
• Copy, paste, clear and undo functions are available for the LFO’s.
34
THE PATTERN SEQUENCER
THE PATTERN SEQUENCER
The sequencer is a central part of the Machinedrum. It is designed to be an inspirational
tool for pattern based rhythms.
The sequencer is designed both for live and studio use. The patterns can either be trigged
individually from the user interface, trigged by MIDI commands or they can be linked
together to form a song.
The sequencer has two main modes of operation, called PATTERN mode and SONG
mode. We will start by taking a look at the PATTERN mode and move on to the SONG
mode, but first we will take a look at a very central concept of the Machinedrum.
CLASSIC VS EXTENDED
The sequencer is tied to parameter control and kit selection in different ways, depending on
the editing mode currently selected.
The key [CLASSIC/EXTENDED] switches between the CLASSIC and the EXTENDED
mode, and the adjacent LED indicates which mode is currently active.
CLASSIC EDITING
In CLASSIC mode, the SPS-1 MKII/SPS-1UW MKII will behave much like a traditional
drum machine. In this mode, patterns simply keep trig information and have no associated
kits or parameter locks. Changing patterns will not recall any kit.
EXTENDED EDITING
In EXTENDED mode, each pattern is associated with a certain kit, which will be recalled
when the pattern is played. This way, you know playing a certain pattern always gives the
same result. In this mode, patterns also keep parameter lock data. See section “PARAMETER LOCKS”, on page 47 for more information about parameter locks. Working with
parameter locks in EXTENDED mode is the key to many unique Machinedrum possibilities.
• In EXTENDED mode, be careful to save any changes you have made to your kit
that you want to keep. Changing a pattern might change kit and then you will lose
the old kit settings.
• In EXTENDED mode, if two patterns use the same kit, the kit will not be reloaded
when changing pattern.
35
THE PATTERN SEQUENCER
TEMPO
THE TEMPO SCREEN
The TEMPO screen is opened by pressing the [TEMPO] key.
Now you can use the SOUND SELECTION wheel to change the current tempo in integer
steps. The [UP] and [DOWN] arrow keys change the decimal part of the tempo. Holding
[FUNCTION] while editing the tempo will delay the actual change of tempo until you
release the key.
• You can temporarily shift the tempo up or down by 10% by pressing the [LEFT] or
[RIGHT] arrow keys. This is very handy when manually syncing your Machinedrum to a turntable. Note that you do not need to be in the tempo screen to perform this tempo shift.
TAP TEMPO
To tap a tempo, hold the [FUNCTION] key and tap the [TEMPO] key at a steady rhythm.
After four consecutive taps the average tempo of the taps will be set as the new tempo and
it will be showed in the TAP TEMPO window. You can continue tapping the [TEMPO] key,
the tapped tempo average will continue updating.
EXTERNAL SYNCHRONIZATION
The Machinedrum SPS-1 MKII/SPS-1UW MKII can be set to either internal or external synchronization.
When in internal clock mode the Machinedrum outputs a high quality MIDI clock on the
MIDI OUT port. This can be used for keeping external gear in sync with the Machinedrum.
When in external midi clock synchronization mode the SPS-1 MKII/SPS-1UW MKII will stay
in sync with an external MIDI clock if present. When in external clock mode the tempo in
the upper left corner of the base LCD screen will show “EXT” for external synchronization.
The tempo screen will show the current average tempo. For more information about this,
see section “SYNC”, on page 75.
• The tempo is not stored in a pattern or a kit. However, songs can store tempo
changes.
36
THE PATTERN SEQUENCER
PATTERN MODE
To edit a pattern, first make sure that the <PATTERN> LED is lit by toggling the [PATTERN/
SONG] key. Then select a pattern as described below. Load a kit that you want to use.
Then edit the pattern, either by using GRID RECORDING or LIVE RECORDING.
PATTERN SELECTION
The Machinedrum has 8 banks of 16 patterns each. The banks are named
A,B,C,D,E,F,G,H. The [BANK] key selects between pattern banks A to D and E to H.
To select a pattern, press and hold the bank name key while pressing the [TRIG] key. For
selecting pattern A05, first make sure the <BANK> LEDs indicate that banks A to D are
selected, then press and hold key [A/E] while pressing the fifth [TRIG] key.
While the [BANK] keys are pressed you can tell which patterns are uninitialised by the 16
<TRIG> LEDs. LEDs that are lit indicate that the corresponding pattern contains data. You
will also see which pattern that is currently selected. The <TRIG> LED corresponding to
the active pattern will give off a rapid double blink.
The [BANK] keys are “sticky”, which means that if you let them go without pressing any
[TRIG] key you still have around two seconds for selecting your pattern. This simplifies one
hand operation of the Machinedrum. A message on screen will indicate that the [BANK]
key still is active and a graphic represantation will tell how much time is left for selecting
your pattern.
If pattern selection is done while the sequencer is playing, the selected pattern will not be
actived until the current pattern has played to its end. You will see the change in the display
as described in section “THE LCD USER INTERFACE”, on page 9.
PATTERN CHAINING
You can use pattern chaining to cue up patterns to be played after each other in a loop, like
a simple live sequencer for patterns. In PATTERN mode, hold a [BANK] button and then
press the [TRIG] keys corresponding to the patterns you want to chain. The patterns will be
chained in the order you select them. It is only possible to chain patterns from one bank,
and each pattern may only be chained once. Chaining is indicated by a double arrow
between the current and the next pattern.
[STOP] changes pattern if a pattern was previously selected as next pattern. That means
that if pattern A01 is started and A02 is cued to play after pattern A01, pressing [STOP]
and then [PLAY] will start playing at A02.
PARAMETER TWEAKING
By pressing the [FUNCTION] key and turning one of the DATA ENTRY knobs, the actual
parameter will be changed for every track. This is a quick way to make patterns sound dramatically different. Note that the values of the manipulated parameters may not be restored
when you turn them back the same amount of steps you first changed them. If track 1 has
a FLTW setting of 0 and track 2 has a FLTW setting of 127 and you change the FLTW
parameter 10 steps clockwise using [FUNCTION] + DATA ENTRY knob, track 1 will display
a FLTW value of 10 while track 2 still will have a value of 127.
• [FUNCTION] + DATA ENTRY knob will not affect UW RAM Recording Machines or
MIDI machines. However, if the active track contains a MIDI machine, [FUNCTION]
+ a DATA ENTRY knob will only affect other tracks containing MIDI machines. The
37
THE PATTERN SEQUENCER
same condition applies if the active track is a UW RAM Recording machine. Note
that CTRL machines are not affected by this function as active track or otherwise.
• When in the TRACK EFFECTS section, use [FUNCTION] + DATA ENTRY knob E or
F to apply a filter sweep to the whole pattern.
• By pressing [FUNCTION] + [CLASSIC/EXTENDED] the saved kit will reload
instantly. This comes in handy when a pattern has been heavily manipulated and
you want to quickly revert it back to its original settings.
SCALE SETUP
It is possible to change the length and step resolution of a pattern. By default a pattern is 4/
4 bars (16 steps) of length.
By pressing the [FUNCTION] key and then the [SCALE SETUP] key, you can set the scale
length and replay speed mode.
There are three values that can be changed in the SCALE SETUP screen. The focus is
moved with the [LEFT] and [RIGHT] keys.
• The leftmost number selects the number of steps in the pattern. The maximum
number of steps is determined by the total length. Use [UP] and [DOWN] to
increase/decrease the number of steps. The [TRIG] keys can also be used to set
the end step.
• The second value selects the total length of the scale. This is either 16, 32, 48 or
64 steps. If you use 17 steps or more in a pattern, the [SCALE SETUP] key is used
in GRID RECORDING mode to toggle the focus between the different pattern
pages.
• The third parameter is the tempo multiplier. There are four possible settings, “1X”,
“2X”, “3/4X” and “3/2X”. 2X allows a pattern to be played back at twice the global
tempo. 3/4X allows a pattern to be played back at three quarters of the global
tempo. 3/2X will play back a pattern twice as fast as the 3/4X setting. Double speed
is useful for increasing the step resolution to 32th notes. Three quarter-speed is
useful when the Machinedrum is playing alongside other instruments set to the
same BPM and you want the Machinedrum to play triplets.
• Even though you set a pattern to have a certain length using scale setup, you can
change this row by row in the song editor. See section “SONG MODE”, on page 51
for more information.
• When changing pattern length from 16 to 64 steps, the first 16-step pattern page
will be copied to all the subsequent pages, if the last other pages previously have
not been programmed.
38
THE PATTERN SEQUENCER
COMPOSING A PATTERN
GRID RECORDING
GRID RECORDING is a method of percussion composing that was first developed in vintage drum machines. In its default state, the 16 [TRIG] keys represent 1 bar of 16th notes.
1. To start recording, press the [RECORD] key. The <RECORD> LED on the left side of the
key is now firmly lit.
2. Select the track you wish to edit using the SOUND SELECTION wheel.
3. You can press [PLAY] if you would like to have the pattern playing during composing.
The LEDs above the [TRIG] keys will start to run to indicate the current step in the pattern. It will loop over and over, until you press [STOP] to stop the playback or [PLAY] to
pause it. The pattern page being played is indicated by the flashing of the corresponding
<PATTERN PAGE> LED.
4. Press the [TRIG] keys to toggle percussion trigging for the corresponding step. The
LEDs above the [TRIG] keys will indicate what steps will be triggered.
5. If the pattern contains more than 16 steps, switch to the pattern page you want to edit by
pressing the [SCALE SETUP] key. The active pattern page is being indicated by a firmly
lit <PATTERN PAGE> LED.
• In the Machinedrum, you work directly in the pattern memory. There is no need to
save patterns. If you wish to keep the data in a pattern, you will have to copy it to
another pattern before you begin editing it. See section “PATTERN COPY”, on
page 43 for more information on copying pattern data.
• If you exit the recording mode, you will not get the running LEDs above the [TRIG]
keys during playback.
• The copy, clear, paste and undo functions operate on a specific track when in
GRID RECORDING mode. See section “TRACK COPY” on page 41.
• The copy, clear, paste and undo functions operate on the full pattern when not in
GRID RECORDING mode. See section “PATTERN COPY” on page 43.
• An easy way to experiment with a pattern is to move all the trigged notes of a track
forwards or backwards. While in record mode, hold down [FUNCTION] while
pressing the [LEFT] or [RIGHT] arrow keys to perform this move. This is especially useful on tracks containing snare drums.
PATTERN PAGE FUNCTIONALITY ON MKI UNITS
On the MKI the pattern page is indicated by the LEDs <1/16>,<1/32:1> and <1/32:2>.
When patterns are up to 16 steps in length only the <1/16> LED is lit. When the pattern is
longer the <1/32:1> LED indicates the editing position being on the first page and <1/32:2>
indicates the second page.
LIVE RECORDING
Live recording is the second method of recording drum trigs. In this recording mode, the
[TRIG] keys are played like a drum set. The current kit is assigned to all [TRIG] keys, so all
16 tracks can be accessed at once.
1. To start recording using direct composing, hold [RECORD] while pressing [PLAY]. This
starts the sequencer recording and the <RECORD> LED starts to flash.
39
THE PATTERN SEQUENCER
2. You can now lay down your beat in real time by triggering the machines in your kit with
the [TRIG] keys.
3. To stop recording, press [STOP]. To exit recording but keep the sequencer playing the
pattern, press [PLAY].
4. To remove notes recorded, hold [EXIT/NO] and a [TRIG] key. All notes will be removed
for the part of the track that is played while the [EXIT/NO] and [TRIG] keys are held.
5.
• All live recorded data will be quantised to the current scale resolution (16th or
32nd notes).
NOTE COPY
It is possible to copy a note trig, complete with all parameter lock settings, and paste it to a
new location in the track.
1. Make sure you are in GRID RECORDING mode, indicated by the <RECORD> LED giv-
ing off a steady light.
2. Press and hold the note trig you want to copy and press the [RECORD] key. A window
saying “COPY NOTE” will appear.
3. Hold the [TRIG] key correspondning to the location you want to paste the note to and
press the [STOP] key to complete the paste operation. A window showing “PASTE
NOTE” will be shown.
CLEAR NOTE PARAMETER LOCKS
Instead of removing the parameter locks from a note you can also use the clear note locks
command.
1. Make sure you are in GRID RECORDING mode. The <RECORD> LED should be lit.
2. Hold and press the [TRIG] key you whose content you want to clear. Then press [PLAY]
to clear the note. The message “CLEAR NOTE LOCKS” will appear.
40
THE PATTERN SEQUENCER
• The clear note lock operation can be undone by performing the clear note operation one more time. The message “UNDO NOTE LOCKS” will be shown in the display.
TRACK COPY
In GRID RECORDING mode, it is possible to copy the contents of one track to another.
1. Make sure you are in GRID RECORDING mode, indicated by the <RECORD> LED giv-
ing off a steady light. Select the source track using the SOUND SELECTION wheel.
2. Hold [FUNCTION] while pressing [RECORD] to copy the data in the track.The message
“COPY TRACK” will be shown in the display.
3. Select the destination track using the SOUND SELECTION wheel.
4. Paste the data by pressing and holding [FUNCTION] and then pressing the [STOP] key.
A message saying “PASTE TRACK” will be shown in the display.
• The track data that is pasted consists of notes, the machine association, LFO settings and, if in EXTENDED mode, parameter locks. If the LFO is set to affect a
parameter on the same track it is remapped as it is pasted. If the LFO is set to
affect a parameter of another track the destination is kept but the LFO depth is set
to zero to avoid confusing results.
• Pasting a track overwrites any previous notes, data and parameter locks.
• The paste track operation can be undone by holding down the [FUNCTION] key
while pressing the [STOP] key. A message saying “UNDO TRACK” will be shown
in the display.
CLEAR TRACK
While in GRID RECORDING mode, it is possible to clear a track.
1. Make sure you are in GRID RECORDING mode. The <RECORD> LED should be lit.
41
THE PATTERN SEQUENCER
2. When you are in the track you wish to clear, press and hold [FUNCTION]. Then press
[PLAY] to clear the track. The message “CLEAR TRACK” will appear.
• The clear track operation can be undone by performing the clear track operation
one more time. The message “UNDO TRACK” will be shown in the display.
TRACK PAGE COPY
In GRID RECORDING mode you can also copy one page of trig data and paste it to
another page.
1. Make sure you are in GRID RECORDING mode, indicated by the <RECORD> LED giv-
ing off a steady light. Select the source track using the SOUND SELECTION wheel.
2. Go to the page you want to copy by pressing the [SCALE SETUP] key.
3. Hold the [SCALE SETUP] key and press [RECORD]. A message saying “COPY PAGE”
page will appear.
4. Go to the pattern page you want to paste the copied page into by pressing the [SCALE
SETUP] key. Paste the data by holding [SCALE SETUP] while pressing the [STOP] key.
A message saying “PASTE PAGE” will be shown in the display
• Pasting a track page overwrites any previous notes, data and parameter locks.
• The track page paste operation can be undone by holding down the [SCALE
SETUP] key while pressing the [STOP] key. A message saying “UNDO PAGE” will
be shown in the display.
CLEAR TRACK PAGE
It is also possible to clear a track page.
1. Make sure you are in GRID RECORDING mode.
42
THE PATTERN SEQUENCER
2. When you are in the track you wish to clear, press and hold [SCALE SETUP]. Then
press [PLAY] to clear the track. The message “CLEAR PAGE” will appear.
• The clear track page operation can be undone by holding the [SCALE KEY] and
pressing the [PLAY] key directly after the clear operation. The message “UNDO
PAGE” will be shown in the display.
PATTERN COPY
To copy the contents of a a pattern to another, follow the steps below.
1. Make sure you are not in GRID RECORDING mode, indicated by the <RECORD> LED
being unlit.
2. Select the source pattern. Hold [FUNCTION] while pressing [RECORD]. A message
“COPY PATTERN” will be shown in the display.
3. Change pattern to the destination where you wish to paste your pattern data by using the
[BANK] and [TRIG] keys.
4. Paste the data by pressing and holding [FUNCTION] and then pressing the [STOP] key.
The message “PASTE PATTERN” will be shown in the display.
• The pattern data that is copied consists of notes, the kit association (in
EXTENDED mode) and parameter locks.
• Pasting a pattern overwrites any previous notes, data and parameter locks.
• The copy pattern operation will copy the whole pattern including unsaved kit
changes.
• You can undo the paste operation by holding the [FUNCTION] key and pressing
the [STOP] key.
43
THE PATTERN SEQUENCER
CLEAR PATTERN
It is possible to clear a whole pattern of its contents.
1. Make sure you are not in GRID RECORDING mode.
2. Select the pattern you want to clear. Press and hold [FUNCTION]. Then press [PLAY] to
clear the pattern. A message “CLEAR PATTERN” will be shown in the display.
• The clear pattern operation can be undone by immediately performing the operation one more time. A message saying “UNDO PATTERN“ will be shown in the display.
TRACK MUTING
THE TRACK MUTE WINDOW
Tracks can be individually muted from the MUTE window. This is useful in a live setting,
you can mute out sounds in a looping pattern, thus creating variations.
1. Hold [FUNCTION] while pressing [A/E] to call forth the MUTE window.
2. In this window, there are 16 squares representing the 16 tracks. Use the [TRIG] keys to
toggle muting of the corresponding tracks. A muted track will be displayed as a “-” sign.
3. While holding [FUNCTION] and pressing the [TRIG] keys, the mute changes will be held
until [FUNCTION] is released. A track that is currently muted but will be unmuted when
[FUNCTION] is released is displayed as a “+” sign. A track that is currently not muted
but will be muted when [FUNCTION] is released is displayed as an “X” sign.
4. Release the [FUNCTION] key to perform all the prepared mute operations.
44
THE PATTERN SEQUENCER
MINIMISING THE MUTE WINDOW
While the MUTE window is active it occupies a large portion of the LCD screen. This can
be disturbing if you want to work with mutes at the same time as you want to access the
sound parameters.
To avoid this problem, the MUTE window transforms to a small centered window when a
DATA ENTRY knob is accessed while in MUTE mode. To return to the big MUTE window,
press the [ENTER/YES] button.
• In songs, mutes can be programmed specifically per row. For more information,
see section “SONG MUTE” on page 55.
• A muted track remains muted, even when the pattern is changed or if SONG mode
is entered or exited.
• Drums already trigged and still making sounds will continue to sound when
muted, but further trigs will be masked. This allows the drums to fade out in a natural way.
ACCENT TRACK
The Accent feature is used for quickly changing the accentuation for either a pattern as a
whole or for individual tracks. Accent raises the volume at selected positions within a pattern or a track.
1. Hold down the [FUNCTION] key while pressing the [B/F] key. This brings forth the
ACCENT window.
2. The accent value is set in steps up to 15, using [UP] and [DOWN] or the SOUND
SELECTION wheel.
3. Toggle the steps to be accented by pressing the [TRIG] keys. Accent is per default set to
ALL and will therefore affect the whole pattern. Place accents by pressing the [TRIG]
keys. Press the [RIGHT] arrow key if you want to accent individual tracks.
4. Move on to the next accent track by holding down [FUNCTION] and pressing the [TRIG]
key corresponding to the track whose accent you want to set.
45
THE PATTERN SEQUENCER
• You can copy, paste, clear and undo accent patterns, tracks and track pages.
Press [FUNCTION] + either the [RECORD], [PLAY] or [STOP] keys while the
ACCENT window is open to perform these operations on the accent pattern or
track. Press [SCALE SETUP] + either the [RECORD], [PLAY] or [STOP] keys if you
want affect the accent track page with these operations.
SWING
THE SWING WINDOW
Swing is used for adding a rhythmic “shuffle” to a pattern or to individal tracks. By default,
the swing will affect every second 16th note, starting on step 2. This is how the swing pattern will be restored after a clear pattern operation and will give the traditional shuffle-style
swing for a 4/4 single speed pattern.
When changing to double speed mode in the SCALE SETUP menu (see page 38) you
need to modify the swing pattern to get the same result in single speed mode. In double
speed mode, activate swing for every fourth note, starting with the third note.
More advanced swing effects can of course be made with other swing pattern setups, but
that is outside the scope of this manual. To add swing to a pattern, follow the steps below.
1. Hold [FUNCTION] while pressing [C/G] to open the SWING window.
2. Use the SOUND SELECTION wheel to set the desired amount of swing. The amount of
swing is set in percent. 50% is the default value, meaning that no swing will be applied,
and the maximum value is 80%.
3. The [TRIG] keys are used for toggling which pattern steps the swing will influence.
You can also have different swing settings for individual tracks. Note though that every
swing track will share the same percentage of swing. Here is how you set individual swing
tracks.
1. Hold [FUNCTION] while pressing [C/G] to open the SWING window.
2. Use the SOUND SELECTION wheel to set the desired amount of swing.
3. The [TRIG] keys are used for toggling which steps the swing will influence. Swing is per
default set to ALL which will affect the whole pattern. Press the [RIGHT] arrow key in
order to select individual swing tracks.
4. Once you have set the swing track and are satisfied, move on to the next swing track by
holding down [FUNCTION] and pressing the [TRIG] key corresponding to the track
46
THE PATTERN SEQUENCER
whose swing you want to set. Note though that all swing tracks use the same percentage of swing.
Below is a figure illustrating how notes are affected by various amounts of swing.
9
13
• You can copy, paste, clear and undo swing patterns and tracks. Press [FUNCTION]
+ either [RECORD], [PLAY] or [STOP] while the SWING window is open to perform
these operations. You can also copy, paste, clear and undo a swing track page by
pressing [SCALE SETUP] + either the [RECORD], [PLAY] or [STOP] keys.
• Try to swing only one or two tracks, for example the hi-hats, for creating rhythms
with a different feel compared to un-swinged patterns.
• Experiment with using only a few swing trigs in a swing pattern. This will create
just a few notes that are slightly off beat which can add a great deal of movement
to a pattern.
PARAMETER LOCKS
A parameter lock is a parameter locked to a certain value for a specific step. Parameter
locks can be programmed in GRID RECORDING mode and recorded in LIVE RECORDING mode. For parameter locks to come into effect, you need to be in EXTENDED mode.
All SYNTHESIS, TRACK EFFECT and ROUTING parameters can be locked. Parameter
locks are a very important part of creating unique and dynamic patterns with the Machinedrum.
PARAMETER LOCKS IN GRID RECORDING MODE
To program parameter locks in GRID RECORDING mode, follow the steps below.
1. First make sure you are in GRID RECORDING mode, by verifying that the <RECORD>
LED is firmly lit.
47
THE PATTERN SEQUENCER
2. Select the track you wish to do parameter locks for, using the SOUND SELECTION
wheel. Select a parameter page (SYNTHESIS, EFFECTS or ROUTING) for the DATA
ENTRY knobs.
3. Press and hold the [TRIG] key for the step where you want to add a lock. While holding
the [TRIG] key, you can now tweak the parameter of your choice with the DATA ENTRY
knobs. You can tell that the parameter has been locked by it being inverted on the LCD
screen. When the [TRIG] key is released, the trig for that position will hold the parameters that you just programmed. You can also click an unlocked DATA ENTRY knob once
to lock it to its current value.
4. You can verify which steps have parameter locks by looking at the <TRIG> LEDs. A
firmly lit <TRIG> LED means that it is not locked, whereas a rapid interval flash indicates
it does have one or more parameter locks.
5. If you want to view the current parameter lock settings for a step, hold the [TRIG] key.
You can tell which parameters are locked by them being inverted on the screen.
6. To remove all parameter locks for a step, hold the [TRIG] key and press the [PLAY] key.
You can also remove the locks by deleting the trig and reinserting it.
7. To remove one of more parameter lock for a step, hold the [TRIG] key and click the
DATA ENTRY knob you want to remove the lock for. You can tell that the lock has been
removed by the inversion disappearing for the parameter clicked.
• A lock is a snapshot of a parameter setting. It changes the parameter value from
its original value stored in the kit, but only for that note trig. The parameter will
change back to its default state on the next trig if no further parameter locks are
made for that note and parameter.
• A pattern can have a total of 64 individually locked parameters divided freely
between all tracks and parameters. When a parameter is locked on one step, that
parameter can be locked to individual values on all the steps of the track.
• Parameter locks only work in EXTENDED mode, but changing mode to CLASSIC
will not affect any pre-recorded locks. They will remain in the pattern, but they will
have no effect until the mode is set to EXTENDED again.
PARAMETER LOCKS IN LIVE RECORDING MODE
In LIVE RECORDING mode, you can record parameter locks live. To do this, follow the
steps below:
1. Go into live recording mode by holding down the [REC] button and then pressing the
[PLAY] key.
2. Select the track for which you wish to enter parameter locks by using the SOUND
SELECTION wheel or by pressing [FUNCTION] + the corresponding [TRIG] key. Select
a parameter page (SYNTHESIS, EFFECTS or ROUTING) for the DATA ENTRY knobs.
3. Record parameter locks by changing the corresponding DATA ENTRY knob while live
recording. When changing a parameter, the parameter lock will be set on the next note
played on the track. If a parameter is not changed between two drum trigs no parameter
lock will be made.
4. To remove specific parameter locks, press and hold [EXIT/NO] and a DATA ENTRY
knob. All parameter locks will be removed for that specific parameter and track on the
steps of the track that is played.
48
THE PATTERN SEQUENCER
• It is often a good idea to edit and fine tune the parameter locks in GRID RECORDING mode, after recording them in LIVE RECORDING mode.
PARAMETER LOCK SLIDE
The default behaviour for parameter locks is that the value changes exactly when the step
is played and not in between. By using slides, you can have the value of a parameter
locked on one step slide gradually to the value on the next. This behaviour is controlled by
the slide pattern or the slide tracks.
For a parameter to slide it needs to be parameter locked at two separate steps. If a slide
trig is set to the same step as there is a parameter lock, the parameter will slide to the next
parameter locked value. The speed of the slide is relative to the current tempo and the
slide is completed when the next position with a drum trig is reached.
To set slide trigs, follow the instructions below.
1. Hold [FUNCTION] while pressing [D/H] to open the SLIDE window.
2. Use the [TRIG] keys to select the steps for which parameter locks will slide to their next
locked value.
To set individual swing tracks, just follow the instructions below.
1. Hold [FUNCTION] while pressing [D/H] to open the SLIDE window.
2. Slide is per default set to ALL which will affect the whole pattern. Press the [RIGHT]
arrow key to be able to set individual slide tracks.
3. Once you have set the slide track and are satisfied, move on to the next slide track by
holding down [FUNCTION] and pressing the [TRIG] key corresponding to the track
where you want to place slide notes. Use the [TRIG] keys to select the steps for which
parameter locks will slide to their next locked value.
49
THE PATTERN SEQUENCER
• The speed of the slide is relative to the current tempo. The slide is always completed exactly when the next position with a drum trig is reached.
• Only parameters that are locked on the steps selected in the slide mode will slide
to their destination. Parameters that are unlocked will not slide.You can copy,
paste and clear slide patterns and tracks. Press [FUNCTION] + either [RECORD],
[PLAY] or [STOP] while the SLIDE window is open to perform these operations.
You can also copy, paste and clear a slide track page by pressing [SCALE SETUP]
+ either the [RECORD], [PLAY] or [STOP] keys. The paste and clear actions can be
undone.
50
SONG MODE
SONG MODE
A song is basically a number of patterns which are played in sequence. Each step in a
song can have its own settings for pattern start position, pattern length, tempo, and mute
information. You can also loop segments of a song or jump between locations within a
song. All this makes for a very powerful way of arranging your patterns. A song can be up
to 256 steps long, and the memory holds 32 songs.
You enter song mode by pressing the [PATTERN/SONG] key, so that the <SONG> LED is
lit. The screen will change to make room for the song list:
LOAD SONG
1. To load a song from memory, you first need to open the SONG window by pressing
[FUNCTION] and the [KIT] key.
2. Move to the LOAD icon and press [ENTER/YES].
3. Choose the song you wish to load from the list by using the [UP] and [DOWN] arrow
keys, and press [ENTER/YES] to execute.
• Loading a song will destroy any unsaved current song settings. Make sure to
store unsaved work you wish to keep before loading a song.
• The song only holds the information on what patterns should be played in
sequence. Accurate playback of a song depends on the patterns it uses being
unchanged since saving. Otherwise the song might sound differently.
• Machinedrum SPS-1 MKII/SPS-1UW MKII recognises MIDI Song Pointer Position,
which means that you can control the position in the song list from an external
sequencer. Note that you cannot reach song positions inside loops.
51
SONG MODE
PLAYING A SONG
1. Make sure that you are in SONG mode, and that a song is presently loaded.
2. To start the playback of a song, press [PLAY]. Pressing [PLAY] again pauses the play-
back.
3. To stop the playback, press [STOP].
NAVIGATING A SONG
The [UP] and [DOWN] keys can be used to manoeuvre the two indicators on the left and
right sides of the new song list. Pressing [ENTER/YES] will move the song pointer to the
position of the arrows.
When playing the song the arrows will blink and at every fourth blink they point in the direction of the song position pointer. When repeating a row in a song the number of turns left is
indicated to the right of the current pattern display.
In song mode [STOP] holds the position and another [STOP] moves the position pointer to
the beginning of the song.
• Songs are played until the end and will then stop. Of course, infinite loops can
make songs that never end.
• The current tempo will change, if the song has tempo changes in it.
SONG EDITING
The Machinedrum song editor is where the song is built. Here patterns are assigned to the
song. The behaviour of the patterns is also set in the song editor.
1. Hold the [FUNCTION] key and press the [KIT] key to open the SONG window.
52
SONG MODE
2. Move to the EDIT icon and press [ENTER/YES] to open the EDIT SONG screen.
This is where you arrange your patterns into a song. You can edit the song while it is
playing. The two filled arrows on each side of one of the steps are the song position
pointers. They indicate which song step the sequencer is currently playing. In the header
of the menu, next to the text “EDIT SONG” there is a counter, indicating how many bars
and beats the song has played.
3. Use the [UP] and [DOWN] keys to select the song row you wish to edit. The [LEFT] and
[RIGHT] keys allow you to move the focus between the pattern, repeat, offset, length,
BPM and mute settings. The SOUND SELECTION wheel alters the value of each setting.
4. The pattern settings are located in the PAT column. The SOUND SELECTION wheel is
used for choosing between patterns and functions. You can also select a pattern by holding the [BANK A-H] key and pressing a [TRIG] key.
5. The END mark indicates the end of the song. When this point is reached, the sequencer
will stop. You can also program loops in this column. See section “SONG LOOP”, on
page 54 for more information on loops.
6. The REP column controls how many times the current pattern will be repeated for that
particular row in the song.
7. Each row in the song can have its own BPM setting. You set the tempo in the BPM col-
umn. If you do not specify a BPM value on a step, the sequencer will use the last one
used in the song. If a song does not have any tempo settings, the sequencer will use the
current tempo.
• To insert a step in the song, use [FUNCTION] together with the [DOWN] key.
• To remove a step in the song, use [FUNCTION] together with the [UP] key.
• Copy, paste, clear and undo functions operate on rows in song edit
53
SONG MODE
SONG ROW OFFSETS AND LENGTHS
The OF LEN column can be used to override the default start offset and length settings for
the pattern assigned to that row.
The default start of a pattern is always zero. This means it will start to play from the beginning. The default length is set from scale setup (see section “SCALE SETUP”, on page 38).
The song row offset and length functions can be used to build complex rhythm structures. It
can also be used for exchanging certain parts of a pattern for certain song rows in order to
add, for example, a fill at the end of a pattern.
SONG TRANSPORT
It is possible to start playback from any row position in a song. To do this, move the editing
focus to the row you wish to start the playback from and press the [ENTER/YES] button. If
not in play mode, you will see the two filled arrows indicating the replay position move to
the current row.
If the song is currently playing when you select another row, you will first get two hollow
arrows on each side of the current row. The hollow arrows indicate which row will play next
once the current row reaches its end.
SONG LOOP
Song loops are a useful tool when creating a song. By using this command you can limit
the number of rows and make the structure of the song clearer. They can also be used for
setting up pattern loops in order to extend the Machinedrum’s limit of maximum 64 steps
per pattern.
To create a loop, turn the SOUND SELECTION wheel in the PAT column to right before the
A01-pattern, after the END indicator. When a loop is selected the second edit column controls which row to loop from. Use the SOUND SELECTION wheel or [BANK A-H] together
with a [TRIG] button to change what row to loop to. The third column selects how many
times the loop should be executed. Use the SOUND SELECTION wheel to select how
many times the loop shall be executed. The loop count can also be set to infinity.
54
SONG MODE
• Loops can be nested.
• A set of infinite loops can be very useful in a live setting. With a set of infinite
loops, the song transport functions can be used to jump between the looping patterns.
SONG JUMP
A loop can also be converted into a jump. A jump will refer to the song pointer position to
the row that you select. Insert a jump by turning the SOUND SELECTION wheel so that the
number of the second loop row becomes a number that is greater than the current row
number. The jump command will appear and no loop count column will be available. Use
the [RIGHT] arrow key to move the focus to the column where you insert which song row
you want the song position pointer to jump to.
SONG HALT
If you set the loop to loop to the current row it will change to a HALT statement. When the
song pointer reaches a HALT statement it will pause the playback. You then need to use
the song transport controls as described on page 54 to select a new position to start from.
SONG MUTE
In songs, you can mute individual tracks for each row. The mute pattern for each row is
accessed by moving the cursor to the MUT column and then pressing [ENTER/
YES].Tracks muted using song mute can not be unmuted using pattern mute.
This takes you to the familiar MUTE window as seen below.
55
SONG MODE
In this window you can set the tracks that will be muted for the row. The standard pattern
mute, set by [FUNCTION] + [A/E], applies as well, so tracks muted there as well as in the
song mute are silent.
SAVE SONG
1. Open the SONG window by holding [FUNCTION] and pressing the [KIT] key.
2. Use the [LEFT] and [RIGHT] keys to move to the SAVE icon. Press [ENTER/YES] to
call the SAVE SONG menu.
3. On the screen, you can find a list of the songs stored in memory. Use the [UP] and
[DOWN] keys to choose among the 32 song slots. Press [ENTER/YES] to select the slot
where you want to save your song.
4. A window opens where you can name the song:
Select characters using the SOUND SELECTION wheel. The arrow [LEFT] and
[RIGHT] keys move the cursor backwards and forwards on the line.
5. Pressing the [FUNCTION] key gives access to the “high score” selection method, in
which you see all characters at the same time. Keep the [FUNCTION] key held while
navigating using the [LEFT], [RIGHT], [UP] and [DOWN] buttons. Release the [FUNCTION] key, when you have found the right letter.
6. Once you are done naming the song, press [ENTER/YES] to save it.
7. If you want to exit without saving a song, press [EXIT/NO].
• The commands copy, paste, clear and undo are available in the SAVE SONG and
LOAD SONG menus.
56
GLOBAL SETTINGS
GLOBAL SETTINGS
The SPS-1 MKII/SPS-1UW MKII offers 8 different global settings positions. The multiple
global setups are useful for using the Machinedrum in more than one setup. You can have
one setup for studio use and another for live use, or maybe several different setups for different parts of your live set.
The items listed below are available in a the GLOBAL SETTINGS menu.
•
•
•
•
•
•
•
•
•
•
•
•
MIDI base channel
TRACK/PATTERN mappings for a MIDI keyboard
Local control on or off
Program change settings
Mechanical settings (MKII units only)
Output routings of tracks
Trig settings
Sysex send of pattern, song and kit data
Sysex receive of pattern, song and kit data
Sample manager (Machinedrum UserWave only)
Tempo and Sync settings
Turbo menu
To select a global setting and edit it:
1. Press [FUNCTION] and then the [PATTERN/SONG] key to open the GLOBAL SET-
TINGS menu.
2. Go to the global setting slot you wish to use, and press [ENTER/YES] to select it.
3. If you wish to enter the menu for the selected slot, you can either press [ENTER/YES]
once more or move the focus to the ENTER field and press [ENTER/YES].
TURBO MENU
The TURBO menu, only available in OS 1.53 and higher, allows you to use the Turbo protocol when connecting the Machinedrum to other units that have the Turbo protocol implemented. This will speed up MIDI transfer times considerably, which is handy if you for
example want to transfer sysex data or samples to another Machinedrum.
57
GLOBAL SETTINGS
1. Connect the MIDI OUT of your Machinedrum to the MIDI IN of the other unit and the
MIDI IN of your Machinedrum to the MIDI OUT of the other unit.
2. Press [FUNCTION] + [PATTERN/SONG] to open up the GLOBAL menu. Use the
[ARROW] keys to select TURBO. Press [ENTER/YES].
3. CURRENT SPEED shows the current multiplier of the MIDI transfer rate. When not con-
nected to a device using Turbo protocol compatible software, the speed will therefore be
x1.0. Select which NEGOTIATE speed you want use. The Machinedrum defaults to x10,
but this value can be lowered should it be needed. Press the [ENTER/YES] button to
start to negotiate. The CURRENT SPEED value will display the change of the MIDI
transfer rate.
• If you link two Machinedrums together where one of them is a MKI model, you
might not be able to get a CURRENT SPEED value exceeding 6.7x.
CONTROL
Here you choose how the Machinedrum will function in a MIDI context. For MKII versions,
this menu also allows you to select the resolution of the encoders.
BASE CHANNEL
Here you set which MIDI channels the Machinedrum will respond and send data to.
Follow these steps to set the MIDI base channel.
58
GLOBAL SETTINGS
1. Select the CONTROL row in the GLOBAL EDIT menu. Then select BASE CHANNEL
and press [ENTER/YES].
2. Select base channel using the [UP] and [DOWN] arrow keys. Press [ENTER/YES] to
make the actual selection.
The MIDI base channel is the first MIDI channel that the SPS-1 MKII/SPS-1UW MKII will
listen to and send data to. If the base channel is set to 1, the Machinedrum will use channels 1 through 4 to send and recognise MIDI data. The reason for using four channels is to
allow for easy access of control change messages to all parameters.
By using four channels in total, we have avoided using “non-registered parameters”
(“NRPN”), which are usually hard to make good use of from keyboards and from many
computer sequencers. In appendix B and C, we will look closer at how to control the
Machinedrum externally.
• If the MIDI base channel is turned below “1-4” it will display “--”. The Machinedrum will then not send out nor react to MIDI data. System common and System
real time MIDI messages, such as MIDI timing and MIDI synchronization, are not
affected. Use the “--” setting when you want to control other synthesizers but not
have them react to the internal sequencer of the Machinedrum. You can of course
still control other synths using the MIDI machines.
MAP EDITOR
The MAP EDITOR is used to setup how the Machinedrum will react to incoming MIDI
notes. You can trigger drum sounds, patterns and the start, stop and play functions of the
sequencer.
1. Select the CONTROL row in the GLOBAL EDIT menu. Then select MAP EDITOR and
press [ENTER/YES].
2. In the GROUP column, choose for which trig category you want to edit the mapping.
TRACK allows you to assign which MIDI notes that should trig which track sounds, PAT
A-H maps MIDI notes to specific patterns and finally CTRL allows you to let MIDI notes
59
GLOBAL SETTINGS
control the transport control of the SPS-1 MKII/SPS-1UW MKII. Then press the [RIGHT]
key to enter the MAPPING column for the chosen group.
3. From here you set the actual mappings for the options available for the group. Use the
SOUND SELECTION wheel to select a MIDI note to map to track, pattern, etc. Then
press [ENTER/YES] to confirm your choice. Please note that each MIDI key only can be
mapped to one function at once. If you select a MIDI key that is already in use, the previous mapping will be removed.
4. In the TRIG window you set how the Machinedrum should react when receiving a trig
signal. When set to GATE the Machinedrum pattern will start to play once receiving a
MIDI NOTE ON command and stop when receiving a MIDI NOTE OFF command. This
basically means that a pattern will play for as long as a key is being held on the external
trigging device. START will immediately initiate the new pattern once trigged. QUE functions much like how the internal Machinedrum sequcencer works, if a pattern is playing
and a new MIDI note is received, the pattern currently playing will play to its end before
patterns are switched.
• If you map a track to “--” it will neither respond to nor send out MIDI NOTE ON or
NOTE OFF messages.
• You can also use an external MIDI device when assigning MIDI notes. Move to the
row for which you want to change mapping, and then send a NOTE ON message
to the Machinedrum MIDI IN port (i.e. play the note on a connected keyboard).
LOCAL CONTROL
This menu is used for turning local control off or on.
1. Select the MIDI row in the GLOBAL EDIT menu. Then select LOCAL CTRL and press
[ENTER/YES].
2. The default setting is ON. When set to OFF, the Machinedrum will not trig internal
sounds when using the sequencer or pressing the [TRIG] keys. It will not react to the
DATA ENTRY knobs either. The unit will only make sounds when trigged by incoming
MIDI data. However, MIDI data is still being sent out from the Machinedrum.
60
GLOBAL SETTINGS
PROGRAM CHANGE
The SPS-1 MKII/SPS-1UW MKII can both transmit and receive MIDI Program change
messages. Here you decide how the Machinedrum should react to these messages.
1. Select the CONTROL row in the GLOBAL EDIT menu. Then select PRG CHANGE and
press [ENTER/YES].
2. You will be presented with available alternatives for handling program changes. When
the program change setting is set to OFF, the Machinedrum will neither transmit nor
receive program change messages. If set to IN the Machinedrum will respond to incoming program changes, but will not send out any program change data when a new pattern is selected. If set to OUT the Machinedrum will send program change messages
when a new pattern is selected, but will not respond to incoming program changes.
MECHANICAL SETTINGS (MKII UNITS ONLY)
If you have a MKII unit you can select the resolution of the encoders.
1. Select the CONTROL row in the GLOBAL EDIT menu. Then select MECH SETTINGS
and press [ENTER/YES].
2. The default resolution setting is 24. Turning an encoder one revolution will cover 24
parameter steps. If you increase the resolution to 32, turning an encoder one revolution
will cover 32 parameter steps.
61
GLOBAL SETTINGS
ROUTING
In the routing menu tracks can be assinged to the six available track outputs. You can also
select how the Machinedrum will react to incoming trig signals.
OUTPUT
Here the output routing of the tracks can be changed.
By default all tracks are routed to the main output. The main output consists of the outputs
A and B configured as a stereo pair. In the OUTPUT menu you can choose to route tracks
to the individual outputs, A to F. This is useful for placing certain tracks on separate mixer
channels, or affecting certain tracks with external effects.
Once you route a track to a single output (A,B,C,D,E or F) you bypass the STEREO MASTER EFFECT system, which is only available for sound leaving the main output. You can
route more than one track to an output if you want to.
To change the track routing to the outputs, follow these steps:
1. Select ROUTING in the GLOBAL EDIT menu. Then select OUTPUT and press [ENTER/
YES]..
2. Use the [UP] and [DOWN] arrow keys to select the track that you wish to route.
3. Select the output that you wish to route, using the [LEFT] and [RIGHT] keys.
• It is possible to route some tracks to the main outputs and others to A or B. This is
probably not very useful, as the tracks routed to A or B will appear as non-
62
GLOBAL SETTINGS
effected tracks hard panned to either left or right. If you use A and/or B as individual outputs, you probably do not want to use the MAIN A+B stereo out at all.
TRIG
Machinedrum SPS-1 MKII/SPS-1UW MKII allows the two audio inputs to be used for connecting external drum pads. The trig system is prepared for standard piezo elements as
used by most pads and require no amplification before being handled by the Machinedrum.
It is possible to set different trig settings for input A and B.
1. Select the ROUTING row in the GLOBAL EDIT menu. Move the focus to TRIG IN A by
pressing the [ENTER/YES] key. This will open the trig setting menu for the external
input.
GATE sets the input gate sensitivity. A low value makes the trig more sensitive.
SENS sets the sensitivity of the inputs. The higher the sensitivity the higher the reaction to
weak signals.
VMIN and VMAX sets the minimum and maximum velocity mapping. This controls the
dynamic range of the connected trig pads.
DEST defines which track sound will be trigged by the incoming signal.
FILE
In this menu, both SysEx and sample transfers are handled.
63
GLOBAL SETTINGS
SYSEX SEND
The sysex send function is used for dumping patterns, songs, kits, global settings or everything at once. It is also possible to dump specific ranges of patterns, kits or songs.
Before sending, make sure the connections are correct. See the figure below for an example of what the connections could look like when sending sysex data to a computer.
MIDI INTERFACE IN
USB CORD
MD MIDI OUT
1. Select the FILE row in the GLOBAL EDIT menu. Then select SYSEX SEND and press
[ENTER/YES].
2. Select the preferred data send method using the [UP] and [DOWN] arrow keys.
3. If the selected send method has the option to select ranges or a specific number, you
can now move the focus to the right. After that, you use [UP] and [DOWN] or the
64
GLOBAL SETTINGS
SOUND SELECTION wheel to select the lower and upper limit of the range. For pattern
selection [BANK A-H] together with [TRIG] buttons can also be used.
4. Make sure that the device you are sending the data to is ready and waiting.
5. To perform the send, press [ENTER/YES]. You will see a sysex message counter on the
bottom of the screen indicating how many sysex messages have been sent out of the
total amount of messages.
• You can always cancel the SYSEX SEND operation by pressing the [EXIT/NO] button.
ALL DATA SYSEX SEND
Use this option when you need to back up the entire memory of your Machinedrum. All patterns, songs, kits and global settings will be transmitted.
• No range can be selected for this send method.
• Because of the large amount of data transmitted, it may take several minutes to
complete the operation.
• On SPS-1UW/SPS-1UW MKII units the samples are NOT sent using ALL DATA
SYSEX SEND. Please refer to section “SAMPLE MANAGER (SPS-1UW/SPS-1UW
MKII ONLY)”, on page 70
• Speed up sysex dump times tenfold by using the Elektron TM-1 MIDI interface.
65
GLOBAL SETTINGS
GLOBAL SYSEX SEND
Sends all or a specific global setting from the 8 slots available.
SONG + PATTERN (+ KIT) SYSEX SEND
Sends the song or songs with the patterns used in them. If you are in EXTENDED mode,
you will also send the kits that are used in the patterns. In CLASSIC mode, you will only
send patterns and song data. Even if you currently are in CLASSIC mode, parameter locks
will still be transmitted. The range selects what song(s) will be sent.
PATTERN (+ KIT) SYSEX SEND
Sends a pattern or several patterns. If you are in EXTENDED mode, you will also send the
kits that are used in the patterns. In CLASSIC mode, you will only send patterns. Although
sent from CLASSIC mode, existing parameter locks will be transmitted. The range selects
the span of consecutive patterns that you wish to send.
KIT SYSEX SEND
Sends a kit or several kits. The range selects the span of consecutive kits.
SYSEX RECEIVE
The sysex receive function makes it possible to restore previously stored data back into the
Machinedrum.
66
GLOBAL SETTINGS
• Note that it is also possible to receive sysex data without being in the SYSEX REC
menu. In fact, you can receive sysex data anytime without having to be in a specific menu. For more info about this, please see “GENERAL SYSEX RECEIVE” on
page 67.
Before receiving data, make sure you have connected the SPS-1 MKII/SPS-1UW MKII
properly to the external device. See the figure below for an example of what the connections could look like when receiving sysex data from a computer.
USB CORD
MD MIDI IN
MIDI INTERFACE OUT
There are two methods for storing received sysex data, ORIGINAL PLACE and SPECIFIC
PLACE. There is also an additional method called VERIFY, which only verifies that the
messages received are correct.
• Receiving data works the same in both the CLASSIC and the EXTENDED edit
modes. If, for instance, patterns are saved with their kits (in EXTENDED mode),
and you receive them back while in CLASSIC mode, you will get the kits as well.
• To ensure that your data was received and stored correctly, please use the VERIFY option.
GENERAL SYSEX RECEIVE
You can send sysex data at any time to the Machinedrum. The playback of the sequencer
will not even halt. This applies to sysex data containing information about patterns, kits and
songs. Note that the only indication of a general sysex receive taking place is the blinking
pixel in the upper left corner of the LCD signalling activity on the MIDI in port. This general
transfer method works just like the original place sysex receive described below.
If you need to place the sysex data at a certain location in the Machinedrum, you need to
enter the SYSEX REC menu.
67
GLOBAL SETTINGS
ORIGINAL PLACE SYSEX RECEIVE
If you still want to use this menu, follow the instructions below.
To load sysex data into the same place as it was originally saved, follow the steps below:
1. Make sure you have connected the Machinedrum MIDI IN port to the MIDI OUT port of
the device that is sending the sysex data.
2. Select the MIDI row in the GLOBAL EDIT menu. Then select SYSEX REC and press
[ENTER/YES].
3. Select the ORIG receive method using the [UP] and [DOWN] arrow keys.
4. Press [ENTER/YES] to start receiving data. A message displaying “WAITING...” shows
up in the menu.
5. Now initiate the data send from the sending device.
6. A counter will display how many messages have been received, and, if you have a bad
connection, how many erroneous messages have been received and ignored.
• Received data will overwrite any previous data in the memory in the positions
where it is placed. Make sure you have backed up any important data using sysex
send.
• Receiving sysex data may take a while, depending on the size of the transmitted
data.
• You don’t have to enter this menu for receiving sysex data. Just send the data to
the Machinedrum at any time and it will store it where it was originally saved. See
“GENERAL SYSEX RECEIVE” on page 67 for more info.
SPECIFIC PLACE SYSEX RECEIVE
To relocate the data that you send to the Machinedrum, you need to use the SPECIFIC
receive method. You can specify starting positions for each category of data. Since the
Machinedrum does not know in advance what kind of and how much data you will send, it
will place the data beginning with the start position you specify. For example, if you specify
68
GLOBAL SETTINGS
KIT:03 and receive four kits, positions 3 to 7 will be written over no matter where the
received kits were originally placed.
To receive the data starting from a specified position, you need to:
1. Make sure that you have connected the Machinedrum MIDI IN port to the MIDI OUT port
of the device that is sending the sysex data.
2. Select the FILE row in the GLOBAL EDIT menu. Then select SYSEX REC and press
[ENTER/YES].
3. Select the SPEC receive method using the [UP] and [DOWN] arrow keys.
4. Move to the box to the right where you can select the starting position for the sysex data
that you will send to the Machinedrum. The first position, KIT, is the kit number that you
wish to start from. The second, PAT, is the pattern start position. The third, SONG, is the
song start position, and finally there is GLOB, which is the global setting start slot. You
set the parameters with the [UP] and [DOWN] keys. You can leave the other parameters
blank and only specify the KIT parameter if, for instance, you only want to transfer kits.
Columns which are not specified are treated as they would be in ORIG mode.
5. Press [ENTER/YES] to start receiving data. The message “WAITING...” shows up in the
menu.
6. Now initiate the data send from the sending device.
7. A message is shown on screen for each chunk of data received.
SYSEX VERIFY
When the verify function receives a sysex dump it will check if the dump contains any
errors. Since it is only a diagnostics tool, it will not overwrite any already existing data
inside the Machinedrum.
1. Make sure that you have connected the Machinedrum MIDI IN port to the MIDI OUT port
of the device that is sending the sysex data.
69
GLOBAL SETTINGS
2. Select the FILE row in the GLOBAL EDIT menu. Then select SYSEX REC and press
[ENTER/YES].
3. Select the VERF receive method using the [UP] and [DOWN] arrow keys.
4. Press [ENTER/YES] to start receiving data. The message “WAITING...” shows up in the
menu.
5. Initiate the data send from the sending device.
6. When the dump is finished you will see how many messages that were received and if
the dump contained any errors. No information has been overwritten.
SAMPLE MANAGER (SPS-1UW/SPS-1UW MKII ONLY)
This menu is where samples can be loaded, sent, erased, etc.
Samples are transferred to and from the SPS-1UW/SPS-1UW MKII via the MIDI ports. The
Machinedrum UserWave uses the MIDI sample Dump Standard (M-SDS) to transfer samples. This standard is supported by various sample editors, but we recommend our free
sample dump program C6, which you can find on the Elektron website. For more information about how to use C6, please check the C6 manual which is also available at the Elektron homepage.
There are two methods available for transferring samples: Closed loop and open loop.
Closed loop needs both the MIDI IN and OUT ports from the sending device connected to
the MIDI IN and OUT ports of the Machinedrum UserWave. Closed loop offers resending
and correction of erroneous data. If only the MIDI OUT port on the sending device is connected to the MIDI IN port on the Machinedrum UserWave, the transmission will resort to
70
GLOBAL SETTINGS
open loop transfer which offers no error correction. During transmission of the samples the
method used will be stated at the bottom of the screen.
In the MODE column you choose which action you want to perform. You can RECEIVE,
SEND and ERASE samples. In the POS/SIZE column all loaded samples and their respective sizes are listed. A slot that displays “--“ is empty. To the right of the POS/SIZE column
you can see what percentage of the DSP memory remains unused.
• All sample speeds from 4 kHz to 48 kHz are accepted and handled by the Machinedrum UserWave. Higher rates are accepted but the samples are downsampled to
half the sampling speed. The Machinedrum UserWave does not handle stereo
samples. All bit depths are accepted but will be played back at 12 bit.
• To preview a sample, move the focus to the POS/SIZE column and press [FUNCTION] + [ENTER/YES] when the sample you want to preview is higlighted. The previewed sample will be replayed using the track currently selected.
• The commands copy, clear, paste and undo are available in the sample manager.
You can, for example, copy content from the RAM machines and paste it into the
ROM slots. This is an easy way to permanently store a RAM machine recording.
• Note that you actually don’t have to be in the SAMPLE MGR menu in order to
receive samples. It is possible to send the samples to the Machinedrum UW at any
time. Note that playback of the sequencer will be halted when transmitting samples.
THE DIFFERENCE BETWEEN ROM AND RAM MACHINES
The Machinedrum offers two types of machines for storing samples: ROM and RAM
machines. The ROM machines keep the samples in memory even after the unit is switched
off. When the unit is turned on the samples stored in the ROM machines will be loaded
instantly.
The RAM machines on the other hand function a bit different. Their content is erased every
time the unit is switched off. You then have to fill them with sound data by either sampling
the internal engine or sample from the external inputs. They are best used for real time
sampling. Read about how they can be used in the “RAM MACHINES TUTORIAL” on
page A-16, found in APPENDIX A.
RAM TO ROM COPY
If you want to permanentely store the content of a RAM machine, you can copy it and paste
it to a ROM machine.
1. While in the SAMPLE MANAGER menu, move the focus to the RAM machine whose
content you wish to copy and then press [FUNCTION] + [REC].
2. Choose the ROM slot you want to copy the RAM machine to and then press [FUNC-
TION] + [STOP]. Since you can’t undo this operation you will be asked whether you
71
GLOBAL SETTINGS
want to perform the action or not. Press [ENTER/YES] if you want to proceed with the
copy operation.
3. A prompt will ask if you want to "RELOAD SAMPLES NOW?".
4. If you press the [ENTER/YES] button the content of all other RAM machines will be
erased. If you want to copy the other RAM machines as well it is very important that you
instead press the [EXIT/NO] key.
5. When you have copied all the RAM machines you can either press the [ENTER/YES]
key when being asked if you want to reload the samples, or exit the SAMPLE MANAGER. In either way, all the RAM machines will be emptied.
GENERAL SAMPLE RECEIVE
You don’t have to be in SAMPLE MGR menu to receive samples. This is possible to do at
any time and in any menu. This method of receiving samples functions exactly the same
way as the ORG option described in “ORIGINAL PLACE SAMPLE RECEIVE” on page 74.
1. Connect the MIDI cables correctly to the Machinedrum UserWave. The MIDI OUT port
on the MIDI interface should be connected to the MIDI IN port on the Machinedrum
UserWave. If you want to use the closed loop transfer method, connect the MIDI OUT of
the UserWave to the MIDI IN of the MIDI interface.
2. Load the samples you want to send to the Machinedrum into a suitable program, for
example C6.
3. Send the samples. A message will appear saying “RECEIVING SAMPLE”. The bar
below the text shows the progress of each sent sample. Playback of the sequencer will
be halted.
4. When the Machinedrum senses that no more samples are sent a new message may
appear stating “CLEANING”. When the cleaning is done the message “LOADING” will
appear and the samples are transferred to the DSP system.
72
GLOBAL SETTINGS
SPECIFIC PLACE SAMPLE RECEIVE
If you want to receive samples using the specific location method, please follow the instructions below.
1. Connect the MIDI cables correctly to the Machinedrum UserWave. The MIDI OUT port
on the MIDI interface should be connected to the MIDI IN port on the Machinedrum
UserWave. If you want to use the closed loop transfer method, connect the MIDI OUT of
the UserWave to the MIDI IN of the MIDI interface.
2. Load the samples you want to send to the Machinedrum into a suitable program, for
example C6.
3. Select the FILE row in the GLOBAL EDIT menu. Then select SAMPLE MGR and press
[ENTER/YES].
4. Select RECEIVE by using the [UP] and [DOWN] keys. Once the RECEIVE option is
highlighted, press the [ENTER/YES] button. The cursor will automatically jump to the
POS/SIZE window.
5. In the POS/SIZE window, choose the slot where you want the Machinedrum to receive
the sample by pressing the [UP] or the [DOWN] keys. Confirm by pressing [ENTER/
YES]. A message saying “WAITING” will start to blink, indicating that the unit is ready to
receive samples. Note that you can always cancel any operation by pressing the [EXIT/
NO] button.
6. Send the samples from your program.
7. When the Machinedrum UserWave is receiving samples, a bar at the bottom of the
screen will appear along with a message saying “RECEIVING”.
8. When the bar has been filled up the sample has been transferred. If there was a sample
in the slot before the new one was transferred, a message saying “CLEANING” will
appear.
73
GLOBAL SETTINGS
ORIGINAL PLACE SAMPLE RECEIVE
The Machinedrum UserWave can also receive several subsequent samples. To do this,
either just send the samples at any time to the unit, as described under “GENERAL SAMPLE RECEIVE” on page 72, or choose the ORG option located at the bottom in the POS/
SIZE menu.
After receiving the first sample the Machinedrum UserWave checks if there are more samples coming. If so, the subsequent samples will be placed after the first one in the order
they are received. Note that these subsequent samples will overwrite any samples that
might be stored in these slots.
• The MIDI Sample Dump Standard offers Sample Position to be included in the
dump. This is handy to use with the ORG method, as you can select any ROM slot
as the starting point for the sample transfer.
• The SPS-1UW/SPS-1UW MKII is always sysex device 0 when receiving data. Typically, you don’t have to bother about this.
• Use the Elektron TM-1 USB MIDI interface for up to 10x faster sample transfer
speed.
SEND SAMPLES
You can send samples from the Machinedrum UserWave to an external device, which will
most likely be a computer. You can use our program C6 for this task as well.
1. Make sure you have conneced the MIDI cables correctly. The MIDI IN port on the MIDI
interface should be connected to the MIDI OUT port on the Machinedrum UserWave. If
you want to use the closed loop transfer method, connect the MIDI IN of the UserWave
to the MIDI OUT of the MIDI interface.
2. Select the FILE row in the GLOBAL EDIT menu. Then select SAMPLE MGR and press
[ENTER/YES]
3. Choose SEND in the MODE menu and press the [ENTER/YES] key. The cursor will
automatically jump to the POS/SIZE window.
4. Set the program you are using to receive the samples with to listen for incoming data.
5. Choose which sample you want to send by using the [UP] and [DOWN] arrow keys.
Confirm the selection by pressing the [ENTER/YES] button. A bar will appear and when
it has filled up the sample has been transmitted. You will also see whether a closed loop
or an open loop transfer method is being used.
74
GLOBAL SETTINGS
• You can send every stored sample to make a complete sample dump. Scroll down
in the POS/SIZE window until you find the option that says ALL.
• You can also transmit samples stored in the RAM machines. Doing this you can
sample sounds from the Machinedrum UserWave and store them externally.
ERASE SAMPLES
Every sample loaded into the UserWave can also be erased. Erasing samples frees up
sample memory.
1. Select MIDI row in the global edit row. Then select SAMPLE MGR and press [ENTER/
YES].
2. Select ERASE by using the [UP] and [DOWN] arrows. Confirm the selection by pressing
the [ENTER/YES] button.
3. Choose which sample you want to erase by using the [UP] and [DOWN] arrows and
then press [ENTER/YES]. You will be prompted to confirm the removal of the sample.
Press the [ENTER/YES] button again to erase the sample. If you do not want to erase it,
press the [EXIT/NO] button.
• You can erase all samples at once. Just choose the ALL option located at the bottom of the scroll list in the POS/SIZE window.
SYNC
The Machinedrum can be synchronized to either internal or external MIDI clock. It can also
be configured to react to and transmit different kinds of control messages which is useful in
a studio environment where the SPS-1 MKII/SPS-1UW MKII is synchronized to other MIDI
devices.
75
GLOBAL SETTINGS
TEMPO IN
The Machinedrum can either follow its internal clock or follow the tempo of an external
source.
1. Select the SYNC row in the GLOBAL EDIT menu. Then select TEMPO IN and press
[ENTER/YES].
When TEMPO IN is set to EXTERNAL the Machinedrum is synced to incoming tempo via
MIDI. When locked to external clock signal, the BPM will display “EXT”. If the Machinedrum
does not receive a clock signal for a couple of seconds, it will revert back to following its
own internal clock.
Note that the internal clock of the SPS-1 MKII/SPS-1UW MKII is extremely precise. If you
are unsure about the timing of the incoming signal, we recommend that you leave the
TEMPO IN setting set to INTERNAL.
• When the Machinedrum is synced to an external clock signal and no longer
detects it, the SPS-1 MKII/SPS-1UW MKII will fall back to its internal clock. In this
situation, the sync source in the global settings will not change. Once the
Machinedrum begins to receive an external clock signal again, it will synchronize
to that signal.
CTRL IN
Here you decide how the Machinedrum should react to incoming MIDI control data.
1. Select the SYNC row in the GLOBAL EDIT menu. Then select CTRL IN and press
[ENTER/YES].
76
GLOBAL SETTINGS
When CTRL IN is set to ON the Machinedrum will respond to MIDI start, stop and continue
messages. Use this setting if you want to control the playback of the Machinedrum from an
external sequencer.
When the CTRL IN option is set to off the Machinedrum will ignore MIDI start, stop and
continue. With this setting the SPS-1 MKII/SPS-1UW MKII can have its tempo synchronized to an external source without having to stop the pattern currently playing if “stop” is
pressed on the external sequencer. This is practical if you want to use the Machinedrum as
a sound module and still have the LFO’s and the Rhythm Echo tempo synchronized.
TEMPO OUT
The Machinedrum can be set to send out tempo information.
1. Select the SYNC row in the GLOBAL EDIT menu. Then select TEMPO OUT and press
[ENTER/YES].
2. When set to ON the Machinedrum will send out MIDI clock. If you are going to tempo
sync other devices to your Machinedrum, make sure this setting is set to ON, otherwise
you can leave it set to OFF.
77
GLOBAL SETTINGS
CTRL OUT
The Machinedrum can be set to send out MIDI control data.
1. Select the SYNC row in the GLOBAL EDIT menu. Then select CTRL OUT and press
[ENTER/YES].
2. If you want to control for example an external sequencer from your Machinedrum you
will need to have CTRL OUT set to ON. The SPS-1 MKII/SPS-1UW MKII will then send
out MIDI start, stop and continue messages. Pressing the [PLAY] key on the Machinedrum will then start the external sequencer, pressing the [STOP] key will stop the external sequencer and so on.
78
EARLY STARTUP MENU
EARLY STARTUP MENU
To access this menu, hold down the [FUNCTION] key while powering up the Machinedrum.
From here you can perform a variety of maintenance tasks. To choose the different alternatives, press the corresponding [TRIG] key.
TEST MODE
To enter this mode, press the first [TRIG] key. If you have any trouble with your Machinedrum and suspect it may be due to a hardware problem, perform this self test. Everything
should come up as shown below. If not, contact Elektron support.
Here you can also check that every button and knob work as intended. Press the buttons
and turn the knobs and the <SOUND SELECTION> LEDs should light up. If something
does not work as supposed, please contact Elektron Support.
EMPTY RESET
To perform this operation, press the second [TRIG] key. This reset will clear all kits, patterns, songs and global settings. If you have a Machinedrum UserWave, an empty reset
will still retain the ROM samples in memory.
FACTORY RESET
To perform this operation, press the third [TRIG] key. This reset restores all patterns, kits,
songs and globals to the factory presets that was preinstalled when the Machinedrum originally shipped. For the Machinedrum UserWave, all ROM samples will also be reverted to
the factory defaults.
SOFT RESET
To perform this operation, press the fourth [TRIG] key. This is a milder form of reset which
will retain all data inside your Machinedrum. After a SOFT RESET no ROM samples will be
loaded for the Machinedrum UserWave. This might fix potential sample-related problems in
the sample manager.
MIDI UPGRADE
By choosing this option, the Machinedrum prepares itself to receive an OS upgrade via
MIDI.
79
EARLY STARTUP MENU
1. Check that all MIDI cables are connected correctly.
2. Load the new OS in an appropriate program capable of sending sysex files. We recom-
mend the program C6 which can be found on the Elektron website. You can also use
another Machinedrum with a more up to date OS. Connect it to the Machinedrum that is
supposed to be upgraded, and transmit the OS. Read more about this procedure in the
“SEND UPGRADE“ section.
3. Choose MIDI UPGRADE by pressing the fifth [TRIG] key. The Machinedrum will wait for
an OS to be transmitted to it and a message stating “READY TO RECEIVE MIDI
UPGRADE…” will appear on the screen.
4. Once the Machinedrum senses that an OS is being sent to it, the <SOUND SELEC-
TION> and the <TRIG> LEDs will light up one after another. Please note that this procedure takes a while.
5. When the transfer is finished the message “PREPARING FLASH” appears.
6. “PREPARING FLASH” is shortly followed by “UPDATING FLASH”. When this process is
finished the OS is updated. After the upgrade the operating system may upgrade the
bootstrap, do not turn off the unit before it has completed its start up sequence or
explicitely tells you to restart!
80
EARLY STARTUP MENU
SEND UPGRADE
With this option you can send the OS installed in your Machinedrum to a friend’s unit.
1. Connect the MIDI OUT on the Machinedrum with the latest OS to the MIDI IN on the
Machinedrum that is going to be upgraded. Enter the EARLY STARTUP menus on both
machines.
2. Enter the MIDI UPGRADE mode in the Machinedrum that is supposed to be upgraded
by pressing the fifth [TRIG KEY]. Make sure you see the message “READY TO
RECEIVE MIDI UPGRADE…” on the screen.
3. Press the sixth [TRIG] key of the Machinedrum that is used to send the OS upgrade.
This will start the transmission of the OS to the other Machinedrum.
• If you have installed OS 1.31 or above you can experience the speed of the Elektron TurboCharge protocol. You will need to have the MIDI IN port of the receiving
machine connected to the MIDI OUT port of the transmitting machine and vice
versa for this to function.
81
TECHNICAL INFORMATION
TECHNICAL INFORMATION
SPECIFICATIONS
PERCUSSION CONTROL SEQUENCER
ELECTRICAL SPECIFICATIONS
16 tracks
128 x 64 step patterns
32 songs
Supports swing, slide and accent
64 possible parameter locks on each pattern step
Full realtime control
Full MIDI support
384 MIDI controllable (MIDI CC) parameters
Impedance balanced audio outputs:
SOUND GENERATION SYSTEM
4 MD Synths
46 individual audio generating machines
5 effects on each track
4 stereo master effects
16 part synthesis
64 user programmable kits
SPS-1UW MKII ONLY
48 ROM slots for storing samples
4 RAM machines for real time sampling
TRACK EFFECTS
Amplitude modulation
1-Band EQ
Resonant 24dB lp/bp/hp filter
Sample rate reduction
Distortion
Main out level: +15dBu
Assignable outs level: +10dBu
Output impedance: 100 Ω unbalanced
S/N ratio: 100dBFS (20-20.000Hz)
Unbalanced audio inputs:
Input level: +7dBu maximum
Audio input impedance: 9 k Ω
SNR inputs: 98dBFS (20-20.000Hz)
Unit power consumption: 10W typical, 18W maximum.
Recommended power supply: 6V DC, 3A
HARDWARE
128x64 pixel backlit LCD
MIDI In/Out/Thru
6 x 1/4” impedance balanced audio out jacks
2 x 1/4” audio in jacks
1 x 1/4” stereo headphone jack
Advanced dual DSP system
44.1kHz, 24-bit D/A and A/D converters
Flash-EEPROM upgradable OS
USERWAVE ONLY
2,5 megabytes of non volatile sample memory
PHYSICAL SPECIFICATIONS
MASTER EFFECTS
Rhythm Echo delay
Gatebox reverb
Hi/Lo-shelf + parametric EQ
Dynamix processor
Steel casing with brushed aluminium panel
Dimensions: W340xD176xH63mm
(height including knobs and rubber feet)
Weight: approximately 2.8 kg
POWER SUPPLY (PSU-2) ELECTRICAL SPECIFICATIONS
Input voltage range: 100-240V (43-60Hz)
Input connector: IEC320-C8 (2 prong)
In-rush current: 50A maximum
Output voltage: 5.7-6.3V DC
Output current: 3.5A maximum
Output connector: 5.5x2.5mm DC plug, power at center
82
DIFFERENCES BETWEEN THE MKI AND MKII MODELS
DIFFERENCES BETWEEN THE MKI AND MKII MODELS
There exist a number of hardware differences between the MKI and MKII models of the
Machinedrum. Below is a compilation of the most important changes.
DESIGN
The height of the Machinedrum MKII is 63mm including rubber feet and knobs.
The height of a MKI unit including rubber feet and knobs is 77mm.
POWER SUPPLY
A switched-mode power supply is used for the MKII models which allow the units to be
used all over the globe without the need of voltage converters. The MKI models use an AC
power supply.
The output specification of the MKI power supply is: 6V AC, 2.5A, 50/60Hz. The plug size
of the MKI supply is the same as a MKII power supply.
S/N RATIO AND OUTPUTS
The S/N ratio of the outputs on the Machinedrum MKII is 100dB. The outputs of the MKII
units are impedance balanced.
The S/N ratio for a MKI unit outputs is 91dB and the outputs are unbalanced.
SAMPLER SPECIFICATIONS (UW MODELS ONLY)
The MKII has 48 ROM slots, 4 RAM machines and 2.5MB of sampling memory.
The MKI has 32 ROM slots, 2 RAM machines and 2.0MB of sampling memory.
PATTERN LENGTH
The pattern length of the MKII units can be up to 64 steps.
The MKI can have patterns containing a maximum of 32 steps.
83
CREDITS
CREDITS
PRODUCT DESIGN AND DEVELOPMENT
Anders Andersson
Magnus Forsell
Anders Gärder
Daniel Hansson
David Möllerstedt
Mikael Räim
ADDITIONAL DESIGN
Göran Finnberg
Jesper Kouthoofd
Erik Larsson
Charlie Storm
Fredrik Åhfeldt
FACTORY DEFAULT SOUND DESIGN
Daniel Troberg
USER’S MANUAL
Thomas Ekelund
Daniel Hansson
Jon Mårtensson
CONTACT INFORMATION
ELEKTRON SUPPORT
[email protected]
ELEKTRON WEBSITE
http://www.elektron.se
DELIVERY ADDRESS
Elektron Music Machines MAV AB
Erik Dahlbergsgatan 3
SE-411 26 Gothenburg
Sweden
84
Appendix A:
MACHINE
REFERENCE
In this appendix, the MD-synths of the SPS-1 MKII/SPS-1UW MKII will be
introduced. The individual machine parameters are presented for reference.
TRX
TRX is inspired by classic analogue drum
machine synthesis. With TRX we have not
tried to recreate any specific existing drum
machine, but to create a classic sound with
extended and relevant controls.
HOLD - Controls the initial hold time for the volume.
TICK - Adds a tick to make the start harder.
NOIS - Adds noise to the start of the sound.
DIRT - Controls a bit reduction function for the bassdrum.
DIST - A special type of distortion.
SNARE DRUM “TRX-SD”
BASS DRUM “TRX-BD”
PTCH - Controls the basic pitch of the drum.
PTCH - Controls the basic pitch of the drum.
DEC - Controls the decay time.
DEC - Controls the decay time.
BUMP - Adds a pitch shift at the start.
RAMP - Ramps the pitch.
RDEC - Speed of pitch ramp.
STRT - Makes the start harder.
NOIS - Adds noise to the start of the sound.
HARM - Adds extra harmonics.
BENV - Controls the envelope of the bump.
SNAP - Amount of snap.
TONE - Changes tonal quality.
TUNE - Detunes the drum.
CLIP - A special type of distortion.
CLIP - A special type of distortion.
BASS DRUM “TRX-B2”
PTCH - Controls the basic pitch of the drum.
DEC - Controls the decay time.
RAMP - Ramps the pitch.
A-1
CLOSED HIHAT “TRX-CH”
TOM “TRX-XT”
PTCH - Controls the basic pitch of the drum.
GAP - Changes the hi-hat gap.
DEC - Controls the decay time.
DEC - Controls the decay time.
RAMP - Ramps the pitch.
HPF - High pass filters the sound.
RDEC - Speed of pitch ramp.
LPF - Low pass filters the sound.
DAMP - Dampens the decay.
MTAL - Adds extra metal character to the sound.
DIST - Distortion.
OPEN HIHAT “TRX-OH”
DTYP - Hardness of the distortion.
CLAP “TRX-CP”
GAP - Changes the hi-hat gap.
DEC - Controls the decay time.
CLPY - Density of the clap.
HPF - High pass filters the sound.
TONE - Changes tonal quality.
LPF - Low pass filters the sound.
HARD - Harder claps.
MTAL - Adds extra metal character to the sound.
RICH - Enhances the richness of the sound.
RATE - Rate of the individual claps.
CYMBAL “TRX-CY”
ROOM - Adds a room sound.
RSIZ - Changes the size of the room.
RTUN - Changes the tonal quality of the room.
RIM SHOT “TRX-RS”
RICH - Adds extra richness to the sound.
DEC - Controls the decay time.
TOP - Amount of high frequency harmonics.
TTUN - Tunes the top.
SIZE - Changes the size of the cymbal.
PTCH - Controls the basic pitch.
PEAK - Gives the sound more edge.
DEC - Controls the decay time.
MARACAS “TRX-MA”
DIST - Distortion.
COW BELL “TRX-CB”
ATT - Length of the attack.
SUS - Length of the sustain.
PTCH - Controls the basic pitch.
REV - Reverses movement of the maracas.
DEC - Controls the decay time.
DAMP - Dampens the sound to make it more sparse.
ENH - Enhances the body of the sound.
RATL - Adds extra rattle to the sound.
DAMP - Dampens the decay part.
RTYP - Type of rattle.
TONE - Changes tonal quality.
TONE - Changes tonal quality.
BUMP - Adds a pitchshift at the start of the sound.
HARD - Gives the sound a harder character.
A-2
Appendix A: MACHINE REFERENCE
CLAVES “TRX-CL”
PTCH - Controls the basic pitch.
DEC - Controls the decay time.
DUAL - Introduces a dual attack.
ENH - Enhances the tone.
TUNE - Detunes the sound.
CLIC - Adds a click at the start.
CONGAS “TRX-XC”
PTCH - Controls the basic pitch of the drum.
DEC - Controls the decay time.
RAMP - Ramps the pitch.
RDEC - Speed of the pitch ramp.
DAMP - Dampens the decay part of the sound.
DIST - Distortion.
DTYP - Hardness of the distortion.
Appendix A: MACHINE REFERENCE
A-3
EFM
MFRQ - The modulation frequency.
The EFM MD-synth introduces Elektron’s
“Enhanced Feedback Modulation” algorithms.
The generated sound ranges from realistic
acoustic drums to wild, chaotic effects.
MDEC - The modulation decay time.
CLIC - Adds a click to the start of the drum.
CLAP “EFM-CP”
BASS DRUM “EFM-BD”
PTCH - Controls the basic pitch of the drum.
DEC - Controls the decay time.
PTCH - Controls the basic pitch of the drum.
CLPS - The number of claps.
DEC - Controls the decay time.
CDEC - The clap decay time. A higher value gives a longer
decay.
RAMP - The pitch ramp depth.
RDEC - The pitch ramp decay time. A higher value gives a
longer decay.
MOD - The frequency modulation depth.
MOD - The frequency modulation depth.
MDEC - The modulation decay time.
MFRQ - The modulation frequency.
HPF - High pass filter frequency.
MFRQ - The modulation frequency.
MDEC - The modulation decay time.
RIMSHOT “EFM-RS”
MFB - Modulation feedback.
SNARE DRUM “EFM-SD”
PTCH - Controls the basic pitch of the drum.
DEC - Controls the decay time.
PTCH - Controls the basic pitch of the drum.
MOD - The frequency modulation depth.
DEC - Controls the decay time.
HPF - High pass filter frequency.
NOISE - The amount of noise in the snare drum.
SNAR - Adds snare drum timbre to the sound.
NDEC - Noise decay time.
SPTC - The pitch of the snare drum timbre.
MOD - The frequency modulation depth.
SDEC - The decay of the snare drum timbre.
MFRQ - The modulation frequency.
SMOD - The modulation depth of the snare drum timbre.
MDEC - The modulation decay time.
COWBELL “EFM-CB”
HPF - High pass filter frequency.
TOM “EFM-XT”
PTCH - Controls the basic pitch.
DEC - Controls the decay time.
PTCH - Controls the basic pitch of the drum.
SNAP - The amount of snap in the beginning of the sound.
DEC - Controls the decay time.
FB - Feedback amount.
RAMP - The pitch ramp depth.
MOD - The frequency modulation depth.
RDEC - The pitch ramp decay time. A higher value gives a
longer decay.
MFRQ - The modulation frequency.
MDEC - The modulation decay time.
MOD - The frequency modulation depth.
A-4
Appendix A: MACHINE REFERENCE
HIHAT “EFM-HH”
PTCH - Controls the basic pitch of the hihat.
DEC - Controls the decay time.
TREM - Depth of the added tremolo.
TFRQ - Frequency of the tremolo.
MOD - The frequency modulation depth.
MFRQ - The modulation frequency.
MDEC - The modulation decay time.
FB - Feedback amount.
CYMBAL “EFM-CY”
PTCH - Controls the basic pitch of the cymbal.
DEC - Controls the decay time.
FB - Feedback amount.
HPF - High pass filter frequency.
MOD - The frequency modulation depth.
MFRQ - The modulation frequency.
MDEC - The modulation decay time.
Appendix A: MACHINE REFERENCE
A-5
E12
E12 is built on carefully processed sampled
percussion sounds with individual control.
BASS DRUM “E12-BD”
BEND - Pitch bend depth. Bends the pitch of the drum up
or down into the basic pitch.
LOW TOM “E12-LT”
PTCH - Controls the basic pitch of the drum.
DEC - Controls the decay time.
PTCH - Controls the basic pitch of the drum.
DEC - Controls the decay time.
SNAP - Depth of the snap. Introduces a more harsh
attack.
HP - High pass filter frequency.
HPQ - High pass filter “Q“ value.
SPLEN - Length of the snap.
START - Moves the start point of the drum forward.
STRT - Moves the start point of the drum forward.
RTRG - Number of drum retrigs.
RTRG - Number of drum retrigs.
RTIM - The time between each retrig. The time is relative
to the tempo.
BEND - Pitch bend depth. Bends the pitch of the drum up
or down into the basic pitch.
RTIM - The time between each retrig. The time is relative
to the tempo.
BEND - Pitch bend depth. Bends the pitch of the drum up
or down into the basic pitch.
CLAP “E12-CP”
SNARE DRUM “E12-SD”
PTCH - Controls the basic pitch of the drum.
PTCH - Controls the basic pitch of the clap.
DEC - Controls the decay time.
DEC - Controls the decay time.
HP - High pass filter frequency.
HP - High pass filter frequency.
RING - Introduces ringing overtones to the sound.
STRT - Moves the start point of the drum forward.
HPQ - High pass filter “Q“ value.
STRT - Moves the start point of the drum forward.
RTRG - Number of drum retrigs.
RTRG - Number of drum retrigs.
RTIM - The time between each retrig. The time is relative
to the tempo.
BEND - Pitch bend depth. Bends the pitch of the drum up
or down into the basic pitch.
RTIM - The time between each retrig. The time is relative
to the tempo.
BEND - Pitch bend depth. Bends the pitch of the drum up
or down into the basic pitch.
RIMSHOT “E12-RS”
HIGH TOM “E12-HT”
PTCH - Controls the basic pitch of the drum.
PTCH - Controls the basic pitch.
DEC - Controls the decay time.
DEC - Controls the decay time.
HP - High pass filter frequency.
HP - High pass filter frequency.
RRTL - Adds “ringing” to the sound.
HPQ - High pass filter “Q“ value.
STRT - Moves the start point of the drum forward.
RTRG - Number of drum retrigs.
RTIM - The time between each retrig. The time is relative
to the tempo.
STRT - Moves the start point of the drum forward.
RTRG - Number of drum retrigs.
RTIM - The time between each retrig. The time is relative
to the tempo.
A-6
Appendix A: MACHINE REFERENCE
BEND - Pitch bend depth. Bends the pitch of the drum up
or down into the basic pitch.
BEND - Pitch bend depth. Bends the pitch of the drum up
or down into the basic pitch.
RIDE CYMBAL “E12-RC”
COW BELL “E12-CB”
PTCH - Controls the basic pitch.
PTCH - Controls the basic pitch of the cymbal.
DEC - Controls the decay time.
DEC - Controls the decay time.
HP - High pass filter frequency.
HP - High pass filter frequency.
HPQ - High pass filter “Q“ value.
BELL - Introduces the sound from the inner bell of a ride
cymbal.
STRT - Moves the start point of the drum forward.
STRT - Moves the start point of the drum forward.
RTRG - Number of drum retrigs.
RTIM - The time between each retrig. The time is relative
to the tempo.
BEND - Pitch bend depth. Bends the pitch of the drum up
or down into the basic pitch.
RTRG - Number of drum retrigs.
RTIM - The time between each retrig. The time is relative
to the tempo.
BEND - Pitch bend depth. Bends the pitch of the drum up
or down into the basic pitch.
CLOSED HIHAT “E12-CH”
CRASH CYMBAL “E12-CC”
PTCH - Controls the basic pitch of the hihat.
PTCH - Controls the basic pitch of the drum.
DEC - Controls the decay time.
DEC - Controls the decay time.
HP - High pass filter frequency.
HP - High pass filter frequency.
HPQ - High pass filter “Q“ value.
STRT - Moves the start point of the drum forward.
HPQ - High pass filter “Q“ value.
STRT - Moves the start point of the drum forward.
RTRG - Number of drum retrigs.
RTIM - The time between each retrig. The time is relative
to the tempo.
BEND - Pitch bend depth. Bends the pitch of the drum up
or down into the basic pitch.
RTRG - Number of drum retrigs.
RTIM - The time between each retrig. The time is relative
to the tempo.
BEND - Pitch bend depth. Bends the pitch of the drum up
or down into the basic pitch.
OPEN HIHAT “E12-OH”
BRUSHED SNARE “E12-BR”
PTCH - Controls the basic pitch of the cymbal.
PTCH - Controls the basic pitch of the drum.
DEC - Controls the decay time.
DEC - Controls the decay time.
HP - High pass filter frequency.
STOP - Sets the length of the sound until it gets stopped
abruptly.
HP - High pass filter frequency.
STRT - Moves the start point of the drum forward.
STRT - Moves the start point of the drum forward.
RTRG - Number of drum retrigs.
RTRG - Number of drum retrigs.
RTIM - The time between each retrig. The time is relative
to the tempo.
RTIM - The time between each retrig. The time is relative
to the tempo.
REAL - Enhances the effect of the brush.
Appendix A: MACHINE REFERENCE
A-7
BEND - Pitch bend depth. Bends the pitch of the drum up
or down into the basic pitch.
BONGO CONGO “E12-BC”
TAMBOURINE “E12-TA”
PTCH - Controls the basic pitch of the drum.
DEC - Controls the decay time.
PTCH - Controls the basic pitch of the tambourine.
HP - High pass filter frequency.
BC - Varies the sound between a bongo and congo drum.
DEC - Controls the decay time.
STRT - Moves the start point of the drum forward.
HP - High pass filter frequency.
RTRG - Number of drum retrigs.
HPQ - High pass filter “Q“ value.
STRT - Moves the start point of the drum forward.
RTRG - Number of drum retrigs.
RTIM - The time between each retrig. The time is relative
to the tempo.
RTIM - The time between each retrig. The time is relative
to the tempo.
BEND - Pitch bend depth. Bends the pitch of the drum up
or down into the basic pitch.
BEND - Pitch bend depth. Bends the pitch of the drum up
or down into the basic pitch.
TRIANGLE “E12-TR”
PTCH - Controls the basic pitch of the triangle.
DEC - Controls the decay time.
HP - High pass filter frequency.
HPQ - High pass filter “Q“ value.
STRT - Moves the start point of the drum forward.
RTRG - Number of drum retrigs.
RTIM - The time between each retrig. The time is relative
to the tempo.
BEND - Pitch bend depth. Bends the pitch of the drum up
or down into the basic pitch.
SHAKER “E12-SH”
PTCH - Controls the basic pitch of the shaker.
DEC - Controls the decay time.
HP - High pass filter frequency.
SLEW - Controls the effect of shaking back and forth.
STRT - Moves the start point of the drum forward.
RTRG - Number of drum retrigs.
RTIM - The time between each retrig. The time is relative
to the tempo.
BEND - Pitch bend depth. Bends the pitch of the drum up
or down into the basic pitch.
A-8
Appendix A: MACHINE REFERENCE
P-I
RIMSHOT “PI-RS”
P-I is the physically informed MD-synth which
simulates the behaviour of acoustic drums.
BASS DRUM “PI-BD”
PTCH - Controls the basic pitch of the rim shot.
DEC - Controls the decay time.
HARD - A higher value gives a harder strike.
RING - The drum’s metallic ringing.
PTCH - Controls the basic pitch of the drum.
DEC - Controls the decay time.
RVOL - The volume of the snares’ rattling.
RDEC - The decay time of the rattling.
HARD - A higher value gives a harder strike.
HAMR - A higher value gives a softer mallet.
METALLICA “PI-ML”
TENS - Regulates the effect of the high tension in the skin
from a hard hit.
DAMP - Regulates the damping in the drum body.
SNARE DRUM “PI-SD”
PTCH - Controls the basic pitch of the sound.
DEC - Controls the decay time.
HARD - A higher value gives a harder strike.
TENS - Regulates the effect of a hard hit.
PTCH - Controls the basic pitch of the drum.
MARACAS “PI-MA”
DEC - Controls the decay time.
HARD - A higher value gives a harder strike.
TENS - Regulates the effect of the high tension in the skin
from a hard hit.
RVOL - The volume of the snares’ rattling.
RDEC - The decay time of the rattling.
RING - The drum’s metallic ringing.
DEC - Sets the decay time of the maraca.
GRNS - Adjusts the number of grains in the maraca.
GLEN - Adjusts the decay time for the individual grains.
SIZE - Regulates the size of the maraca.
TOM “PI-XT”
HARD - Regulates the hardness of the grains.
HI HAT “PI-HH”
PTCH - Controls the basic pitch of the drum.
DEC - Sets the decay time of the drum.
HARD - A higher value gives a harder strike.
HAMR - A higher value gives a softer mallet.
TUNE - Emulates different tuning of skins.
PTCH - Controls the basic pitch of the hi hat.
DEC - Sets the decay time of the hi hat.
DAMP - Regulates damping in the drum body.
CLSN - Simulates slight contact between the two cymbals
of the hihats.
SIZE - Regulates the size of the drum body.
RING - Controls the amount of ringing in the sound.
POS - Moves the striking point from the center to the edge.
AG - Enhances the high frequencies of the sound.
AU - Decreases the high frequencies of the sound.
BR - Controls the low frequences of the sound.
CLOS - Sets the time to closing the hi hat. A value of 127
means that that the hi hat does not close.
Appendix A: MACHINE REFERENCE
A-9
RIDE CYMBAL “PI-RC”
PTCH - Controls the basic pitch of the ride.
DEC - Sets the decay time of the ride.
HARD - Adds the impression of a hard hit.
RING - Controls the amount of ringing in the sound.
AG - Enhances the high frequencies of the sound.
AU - Decreases the high frequencies of the sound.
BR - Controls the low frequences of the sound.
GRAB - Sets the time to grabbing the cymbal. A value of
127 means that that the cymbal is never grabbed.
CRASH CYMBAL “PI-CC”
PTCH - Controls the basic pitch of the crash.
DEC - Sets the decay time of the crash.
HARD - Adds the impression of a hard hit.
RING - Controls the amount of ringing in the sound.
AG - Enhances the high frequencies of the sound.
AU - Decreases the high frequencies of the sound.
BR - Controls the low frequences of the sound.
GRAB - Sets the time to grabbing the cymbal. A value of
127 means that that the cymbal is never grabbed.
A-10
Appendix A: MACHINE REFERENCE
GND
GND is not really an MD-synth. It contains
some miscellaneous machines that can be
used for adding extra tonality, and an “empty”
machine called “---”.
ATCK - The input gate attack time. A high value makes the
gate open more slowly.
HLD - The input gate hold time. This parameter controls
how long the gate will be fully open for after the input signal level drops below the gate sensitivity level.
DEC - The input gate decay time. Sets the gate decay time
which comes after the gate hold phase.
SINUS “GND-SN”
INPUT FILTER FOLLOWER A/B “INP-FA/B”
This is an input envelope lowpass filter follower for the
A and B inputs. It is made for passing through external
audio. It does not react to trigs, other than you need to
trig it once for it to become active.
PTCH - Controls the basic pitch.
DEC - The decay time. A higher value gives a longer
decay.
RAMP - The pitch ramp.
RDEC - The pitch ramp decay.
ALEV - Controls the input volume.
NOISE “GND-NS”
GATE - The input gate sensitivity. A low value lets lower
signals through the gate.
FATK - The input filter attack time. A high value makes the
gate open more slowly.
DEC - The decay time. A higher value gives a longer
decay.
FHLD - The input filter gate hold time. This parameter controls how long the gate will be fully open for after the input
signal level drops below the gate sensitivity level.
FDEC - The input filter gate decay time. Sets the gate
decay time which comes after the gate hold phase.
IMPULSE “GND-IM”
FDPH - The input filter cutoff depth value. This controls
how much the filter cutoff value will be influenced by the
input gate envelope.
FFRQ - The input filter base cutoff frequency.
UP - The time that the impulse stays positive.
FQ - The input filter Q value.
UVAL - The value of the positive phase.
DOWN - The time that the impulse stays negative.
DVAL - The value of the negative phase.
INP
INPUT ENVELOPE A/B “INP-EA/B”
This is an envelope that treats external audio as a percussion source. It has two active envelopes, one for
the external audio and one the extra built in lowpass
filter. The envelopes are trigged using the standard
drum trig buttons.
The INP synth contains the machines that
effect the two external inputs of the Machinedrum.
INPUT GATE A/B “INP-GA/B”
This is a gate for the A and B inputs. It is made for
passing through external audio. It does not react to
trigs, other than you need to trig it once for it to
become active.
AVOL - Controls the input volume (Amplitude).
AHLD - The input amplitude hold time. A high value keeps
the input amplitude gate open longer.
ADEC - The input amplitude decay time.
FQ - The input filter Q value.
FDPH - The input filter cutoff depth value. This controls
how much the filter cutoff value will be influenced by the
input filter envelope.
VOL - Controls the input volume.
FHLD - The input filter cutoff hold time.
GATE - The input gate sensitivity. A low value lets lower
signals through the gate.
FDEC - The input filter cutoff decay time.
FFRQ - The input filter base cutoff frequency.
Appendix A: MACHINE REFERENCE
A-11
MID
The MIDI machines are used for controlling
external MIDI gear, such as synthesizers, connected to the MIDI OUT port of the Machinedrum. There are 16 MIDI machines in total,
each connected to the corresponding MIDI
channel. As there is no internal audio processing fo these machines, their controls extend
over the SYNTHESIS, EFFECT and ROUTING menus.
CC4D - Selects the Control Change message to be controlled by CC4V.
Routing window
CC5D - Selects the Control Change message to be controlled by CC5V.
CC5V - Sets the value of the Control Change chosen in
CC5D.
Synthesis window
PCHG - Performs a Program Change message between 0
and 126.
LFOS - Controls the speed of LFO of the MIDI machine.
LFOD - Controls the depth of the LFO of the MIDI
machine.
NOTE - Selects the MIDI note to be triggered, ranging from
C-2 to G8.
LFOM - Controls the balance between the waveforms of
the LFO of the MIDI machine.
N2 - If N2 differs from 0 it adds a second note (chord) N2
number of semitones from NOTE.
N3 - If N3 differs from 0 it adds a second note (chord) N3
number of semitones from NOTE.
LEN - Sets the length of the notes.
VEL - Sets the velocity for NOTE, N2 and N3.
PB - Controls the Pitch bend settings.
MW - Controls the Modulation Wheel.
AT - Controls the channel After Touch.
Track effects window
CTR
The control machines are used to automate
and making it easier to control the different
parameters of the sixteen available tracks as
well as offering control over the stereo master effects. Note that you can use LFO’s
alongside the stereo master effect control
machines, but not with the other control
machines.
CONTROL ALL “CTR-AL”
CC1D - Selects the Control Change message to be controlled by CC1V.
CC1V - Sets the value of the Control Change chosen in
CC1D.
CC2D - Selects the Control Change message to be controlled by CC2V.
CC2V - Sets the value of the Control Change chosen in
CC2D.
CC3V - Sets the value of the Control Change chosen in
CC3D.
This machine simultaneously controls the chosen
parameter or parameters for all 16 tracks. Manipulating
one parameter on the CTR-AL machine will affect the
corresponding parameter on all 16 tracks. Note that
CTRL-AL does not affect the MIDI machines or the
SYNTHESIS page of RAM RECORD machines. The
functionality of this machine is similar to the [FUNCTION] + DATA ENTRY knobs operation described on
page 37 . The major difference is that using this
machine, you can set trigs.
Synthesis window
This page controls the up to 8 available synthesis
parameters for every machine and track.
CC3D - Selects the Control Change message to be controlled by CC3V.
CC4V - Sets the value of the Control Change chosen in
CC4D.
A-12
Appendix A: MACHINE REFERENCE
Track effects window
Here you control the track effect parameters for all
tracks.
P1 TRK - Chooses the track that will be affected by the P1
parameter on the SYNTHESIS page.
P1 PAR - Chooses which parameter that will be affected
by the P1 parameter on the SYNTHESIS page.
P2-P4 TRK - The same function as P1 TRK
P2-P4 PAR - The same function as P1 PAR
Routing window
Routing window
Here you control the routing page parameters for all
tracks.
A continuation of the content in the EFFECTS menu.
The next 4 routings are made here.
CONTROL RHYTHM ECHO DELAY “CTR-RE”
CONTROL 8 PARAMETERS “CTR-8P”
This Control machine is used for grouping together
the parameters you manipulate the most into a single
window. The parameters can belong to different
tracks. This can be convenient in a live situation,
allowing less pressing of buttons to reach the desired
parameters. One CTR-8P machine can contain 8 of
these track and parameter short cuts. The CTR-8P can
also function as a sort of “trigless trig” since it can
manipulate parameters without trigging the corresponding drum sound.
Use this control machine to control the parameters of
the RHYTHM ECHO delay. The effects and routing
pages look the same for all the master effect control
machines, therefore they will be described only for the
RHYTHM ECHO delay.
Synthesis window
This page shows the same parameters as found in the
STEREO MASTER EFFECTS menu under the ECHO
tab.
Synthesis window
This page shows an overview of all the grouped
parameters, which tracks they belong to and what values they have.
TIME - Controls the actual delay time. It is relative to the
current tempo, and it is measured in 128th notes. For
instance, for a two beat delay (8 16th notes) TIME should
be set to 64.
MOD - Controls the delay time modulation depth.
MFRQ - Controls the delay time modulation frequency.
P1 - First shown is the track that P1 is assigned to. Under
the displayed track, the controlled parameter is visible.
Under this, the current value of the parameter is represented. Manipulating P1 will therefore manipulate the chosen parameter on the selected track.
FB - Controls the delay feedback amount. The feedback is
taken after the filter but before the out gain control. FB set
to central position with filter totally open gives unity feedback.
FILTF - The filter base frequency parameter. For a
description of the functionality of the filter, see “THE
RHYTHM ECHO DELAY” on page 29.
P2-P8 - The same function as P1
Track effects window
In this window, together with the ROUTING menu, you
assign the parameters and tracks that are going to be
visible in the overview in the SYNTHESIS menu. You
set up 4 of these track and parameter short cuts in the
TRACK EFFECTS window.
FILTW - The filter width parameter. Please refer to the text
found under the heading “THE RHYTHM ECHO DELAY”
on page 29 for a description of the functionality of the filter.
MONO - the feedback panning control parameter. A low
value gives ping pong style delay, a high value preserves
the stereo information, and a central position brings the
delay feedback into the central panning position.
LEV - The out gain level control of the RHYTHM ECHO
delay.
Appendix A: MACHINE REFERENCE
A-13
CONTROL MASTER EQ “CTR-EQ”
Effects window
This window is empty as no relevant controls can be
found here.
Use this control machine to control the parameters of
the MASTER EQ equalizer. The effect and routing
pages function the same way as described for the
RHYTHM EHCO delay.
Synthesis window
This page shows the same parameters as found in the
STEREO MASTER EFFECTS menu under the EQ tab.
Synthesis window
Here controls for the LFO of the track can be found.
LF is the cut/boost frequency parameter of the low shelf filter.
LFOD - Controls the depth of the LFO.
LG is the low shelf gain parameter that controls how much
the low frequencies should be boosted / reduced between
-15dB and +15dB.
LFOM - Controls the balance between the waveforms of
the LFO.
HF is the cut/boost frequency parameter of the high shelf
filter.
LFOS - Controls the speed of LFO.
CONTROL GATE BOX REVERB “CTR-GB”
Use this control machine to control the parameters of
the GATE BOX reverb. The effect and routing pages
function the same way as described for the RHYTHM
EHCO delay.
Synthesis window
This page shows the same parameters as found in the
STEREO MASTER EFFECTS menu under the REV tab.
HG is the high shelf gain parameter that controls how
much the high frequencies should be boosted / reduced
between -15dB and +15dB.
PF is the parametric EQ frequency parameter, that is the
center frequency of the parametric EQ band.
PG is the parametric EQ gain parameter. It controls how
much the parametric EQ should boost or reduce between 15dB and +15dB, at the frequency set by the “PF” parameter.
PQ is the parametric EQ Q factor. The Q controls the width
of the band that is boosted or reduced by the parametric
EQ. High Q-values give a narrow band.
GAIN is the final out volume control. This parameter allows
you to adjust the out volume of the main stereo out.
DVOL is the delay to reverb level parameter. This parameter allows the output of the RHYTHM ECHO to be routed
into the GATE BOX reverb.
PRED is the pre-delay parameter. The direct and delay
signal mix is delayed by an amount of time to give the
impression of the reverbation arriving after the sound.
DEC is the decay time parameter. Decay time is the time it
takes for the reverbation to die out after a sound has
ended. The decay parameter is active in the range of 0.5 to
3 seconds.
CONTROL DYNAMIX PROCESSOR “CTR-DX”
Use this control machine to control the parameters of
the DYNAMIX dynamic processor. The effect and routing pages function the same way as described for the
RHYTHM EHCO delay.
Synthesis window
This page shows the same parameters as found in the
STEREO MASTER EFFECTS menu under the DYN tab.
DAMP is the damping control parameter. Damping
decreases the high frequencies to give the impression of
soft walls.
HP is a high-pass filter, filtering the output from the reverb.
LP is a low-pass filter, filtering the output from the reverb.
GATE sets the gate time. The reverbated signal is gated
after this time, if the signal level is low. The maximal value
for this parameter gives infinite time - in other words, the
gate is off.
LEV is the output level parameter of the GATE BOX
reberb.
A-14
ATCK controls the attack time, which is the time it takes
the volume detector to react to the Attack part of the sound
signal. Long attack times let fast transients through the
compressor.
REL controls the release time. This is the time it takes the
volume detector to react to the Release part of the sound
Appendix A: MACHINE REFERENCE
signal. A long release time lifts the signal level as a sound
decays, flattening the dynamics.
RTRG - Sets the number of times a sample will retrig. If set
to 127 the sample will retrig infinitely.
TRHD sets the threshold level where the signal starts getting compressed (from -48 to 0dB).
RTIM - Defines the time between two retrigs. The time is
relative to the tempo. If the value is set to zero the RTRG
parameter will not affect anything.
RTIO controls the ratio by which the signal is compressed,
when the threshold level is reached. The ratio has a value
in the range 1:1 to 1:256.
KNEE controls the soft knee transition. It makes the transition between compressed and uncompressed signal
smoother, by softening the knee. A low value gives a hard
knee.
HP is the side chain High pass filter. This parameter highpass filters the sidechain signal of the Compressor, so that
it does not react to bass.
OUTG out gain raises the signal level. This is used to
make up for the gain lost in the compressor.
MIX controls the cross mix between the compressed signal
and the original signal. A high value bypasses the
DYNAMIX processor.
The ROM machines ROM-25 to ROM-48 operates
slightly differently since they are optimized for loops.
How the parameters differ from the other ROM
machines is described below.
HOLD - Set to a value of 127 the amplitude envelope is
open for 2 bars. A setting of 1 will keep the envelope open
for ¼ of a step (1/16 note)
STRT - This parameter is now linear which makes it easy
to find a position within a loop. In a 2-bar loop you will find
each ¼ note located every 128/8 = 16 parameter steps. So
for every 16 steps of the parameter you will find each beat
in the loop.
END - Also linear and functions basically the same way as
the STRT-parameter.
ROM (SPS-1UW ONLY)
The ROM Machines contains user exchangeable samples. There are 48 ROM machines in
total. Use these machines to add your personalized samples to the Machinedrum environment.
The content of the ROM machines remains in
the memory of the Machinedrum after powering down the unit.
ROM MACHINES “ROM-1 - ROM-48”
RAM (SPS-1UW MKII ONLY)
The RAM machines are designed for capturing sound in real time. They function a little bit
different from the other machines.
In order to capture and replay sound two different machines are needed, the RAM
RECORD and the RAM PLAY machines.
The content of the RAM machines are lost
when powering down the Machinedrum.
RAM RECORD “RAM-R1 - RAM-R4”
PTCH - Adjusts the pitch two octaves up or down. For the
first octave up or down, every third parameter step adjusts
the pitch one semi-note.
DEC - The Decay time. If the sample is looped, a setting of
127 will make it loop infinitely.
HOLD - Hold the amplitude envelope open for the specified time. A value of 127 keeps the envelope open for 1 bar
(16 steps). A value of 1 will keep the envelope open for 1/8
of a step.
These machines are used to capture sound. The RAM
RECORD machines can capture both internal sounds
and external sounds. You have 4 RAM RECORD
machines at your disposal.
Some DSP memory is always reserved for the RAM
machines. The memory is shared with the ROM
machines so the more memory left for the RAM
machines, the higher will the quality of the recording
be.
BRR - Bit Rate Reduction. When set to 127 the sample will
be of 2-bit quality.
STRT - Controls the start point of the sample. The parameter is exponential, giving a very fine control over the beginning of a sample.
END - Controls the end point of the sample. The sample
will be reversed if it is set to a lower value than the STRT
parameter.
MLEV – Sets the level of internal sound that is rerouted
from the Main outputs to the RAM RECORD machine.
When set to 0 the signal will be recorded “as is”. If set to a
positive value the recorded signal will increase in volume
compared to the original signal. If set to a negative value
the signal will decrease in volume.
Appendix A: MACHINE REFERENCE
A-15
MBAL – The recording is made monophonic and this
parameter decides how the recording from the Main outs
should be balanced.
3. Assign the first RAM PLAY machine (RAM-P1) to track
M2. This machine will play back the captured sample of
the RAM RECORD machine.
ILEV – Sets the level of input from the external inputs.
When set to 0 the signal will be recorded “as is”. If set to a
positive value the recorded signal will increase in volume
compared to the original signal. If set to a negative value
the recorded signal will decrease in volume.
4. Scroll the SOUND SELECTION wheel until track M1,
the track with the RAM RECORD machine, becomes
active.
IBAL – The recording is made monophonic. This parameter decides how the recording from the external inputs
should be balanced.
CUE1 – Sets the level of pre-listening for the sound coming from either the Main outputs or the external inputs. Be
careful with this parameter as it can generate feedback if
set too high.
5. Enter the SYNTHESIS page of the RAM RECORD
machine and make sure that MLEV is set to zero. Turn
down ILEV to -64. Doing this you will record sound from
the main outs and nothing from the external inputs. LEN
should be set to 64 and RATE to 127. This will capture one
bar with maximum recording quality.
CUE2 – Sets the pre-listening level of what is going to be
recorded if the RAM RECORD machine is triggered.
LEN – Defines how long the recording will be. A value of
127 will record for 2 bars. Each parameter value is ¼ of
step. If running low on DSP memory, turn this value down.
RATE – Turning this down will lower the quality of the
recording.
RAM PLAY “RAM-P1 - RAM-P4”
This machine is used for playing back the sound that
the corresponding RAM RECORD machine has captured. It functions exactly the same way as the ROM
machines 25-48.
6. Press the [REC] button and place a trig on the first step
of the pattern, then press [PLAY]. When the <TRIG> leds
of the pattern sequencer moves over the RAM RECORD
trig, the machine will start to record sound. Remove the trig
right after it has been trigged. This is because we don’t
want the machine to record a new take. The loop is now
stored in the RAM RECORD machine. It is time to play it
back.
7. Scroll the SOUND SELECTION wheel until track M2,
the track with the RAM PLAY machine, becomes active.
8. Make sure that the <RECORD> led is still lit and the
place a trig on step 5 of the pattern sequencer. You should
now hear the captured loop start playing over the already
programmed beat, changing the rhythm considerably.
9.Try experimenting with the loop. Place a trig on step 9 of
the pattern sequencer and parameter lock the STRT
parameter to a value of 16. The recorded loop will now
begin from a different start point further changing the style
of the beat.
RAM MACHINES TUTORIAL
The concept of how the RAM machines function can
be a bit hard to grasp since they work so differently
from the rest of the machines in the Machinedrum.
Here follows a short tutorial of how to set them up for
recording and playing back the sound from the main
outs. This tutorial assumes you are familiar with the
basic operation of the Machinedrum UserWave.
1. Make sure that the main out of Machinedrum UserWave
is connected to your mixer or sound card. You can also
plug a pair of headphones into the phones output. Compose a 1-bar pattern consisting of a bass drum, a snare
drum and some hi hats. The pattern should not contain any
other machines.
2. Assign the first RAM RECORD machine (RAM-R1) to
track M1. This machine will be used to capture the beat.
A-16
Appendix A: MACHINE REFERENCE
Appendix B:
MIDI CONTROL
REFERENCE
All machine parameters in the Machinedrum are accessible from MIDI control change messages. This appendix lists the available MIDI CTRL-change
mappings. The default MIDI NOTE ON mappings are also listed, although
these can be changed using the internal MIDI map editor.
DEFAULT MIDI MAPPINGS
CTRL-CHANGE MAPPINGS
MIDI base channel + 0:
+----------+------+-------+
| hex dec | note | track |
+----------+------+-------+
| 24
36 | C2 | 1
|
| 26
38 | D2 | 2
|
| 28
40 | E2 | 3
|
| 29
41 | F2 | 4
|
| 2b
43 | G2 | 5
|
| 2d
45 | A2 | 6
|
| 2f
47 | B2 | 7
|
| 30
48 | C3 | 8
|
| 32
50 | D3 | 9
|
| 34
52 | E3 | 10
|
| 35
53 | F3 | 11
|
| 37
55 | G3 | 12
|
| 39
57 | A3 | 13
|
| 3b
59 | B3 | 14
|
| 3c
60 | C4 | 15
|
| 3e
62 | D4 | 16
|
+----------+------+-------+
+----------+------+---------+
| hex dec | note | pattern |
+----------+------+---------+
| 40
64 | E4 |
A01
|
| 41
65 | F4 |
A02
|
| 43
67 | G4 |
A03
|
| 45
69 | A4 |
A04
|
| 47
71 | B4 |
A05
|
| 48
72 | C5 |
A06
|
| 4a
74 | D5 |
A07
|
| 4c
76 | E5 |
A08
|
| 4d
77 | F5 |
A09
|
| 4f
79 | G5 |
A10
|
| 51
81 | A5 |
A11
|
| 53
83 | B5 |
A12
|
| 54
84 | C6 |
A13
|
| 56
86 | D6 |
A14
|
| 58
88 | E6 |
A15
|
| 59
89 | F6 |
A16
|
+----------+------+---------+
+---------+------------------------------------+-----+-----+
| hex dec | Parameter
| Trn | Rec |
|---------+------------------------------------+-----+-----+
| 08
08 | Track 1 BD - Level
| X | X |
| 09
09 | Track 2 SD - Level
| X | X |
| 0a
10 | Track 3 HT - Level
| X | X |
| 0b
11 | Track 4 MT - Level
| X | X |
| 0c
12 | Track 1 BD - Mute (>0 mutes trk)
| X | X |
| 0d
13 | Track 2 SD - Mute (>0 mutes trk)
| X | X |
| 0e
14 | Track 3 HT - Mute (>0 mutes trk)
| X | X |
| 0f
15 | Track 4 MT - Mute (>0 mutes trk)
| X | X |
| 10
16 | Track 1 BD - Machine parameter 1
| X | X |
| 11
17 | Track 1 BD - Machine parameter 2
| X | X |
| 12
18 | Track 1 BD - Machine parameter 3
| X | X |
| 13
19 | Track 1 BD - Machine parameter 4
| X | X |
| 14
20 | Track 1 BD - Machine parameter 5
| X | X |
| 15
21 | Track 1 BD - Machine parameter 6
| X | X |
| 16
22 | Track 1 BD - Machine parameter 7
| X | X |
| 17
23 | Track 1 BD - Machine parameter 8
| X | X |
| 18
24 | Track 1 BD - AM Depth
| X | X |
| 19
25 | Track 1 BD - AM Rate
| X | X |
| 1a
26 | Track 1 BD - EQ Freq
| X | X |
| 1b
27 | Track 1 BD - EQ Gain
| X | X |
| 1c
28 | Track 1 BD - Filter base frequency | X | X |
| 1d
29 | Track 1 BD - Filter width
| X | X |
| 1e
30 | Track 1 BD - Filter Q
| X | X |
| 1f
31 | Track 1 BD - Sample rate reduction | X | X |
| 20
32 | Track 1 BD - Distortion
| X | X |
| 21
33 | Track 1 BD - Volume
| X | X |
| 22
34 | Track 1 BD - Pan
| X | X |
| 23
35 | Track 1 BD - Delay send
| X | X |
| 24
36 | Track 1 BD - Reverb send
| X | X |
| 25
37 | Track 1 BD - LFO Speed
| X | X |
| 26
38 | Track 1 BD - LFO Amount
| X | X |
| 27
39 | Track 1 BD - LFO Shape
| X | X |
| 28
| ..
| 3f
40 | Track 2 SD - Machine parameter 1
.. | ...
63 | ...
|
X
|
X
|
| 48
| ..
| 5f
72 | Track 3 HT - Machine parameter 1
.. | ...
95 | ...
|
X
|
X
|
| 60
| ..
| 77
96 | Track 4 MT - Machine parameter 1
.. | ...
119 | ...
|
X
|
X
|
This mapping can be changed in the MIDI map editor.
B-1
MIDI base channel + 1:
MIDI base channel + 3:
+---------+------------------------------------+-----+-----+
| hex dec | Parameter
| Trn | Rec |
|---------+------------------------------------+-----+-----+
| 08
08 | Track 5 LT - Level
| X | X |
| 09
09 | Track 6 CP - Level
| X | X |
| 0a
10 | Track 7 RS - Level
| X | X |
| 0b
11 | Track 8 CB - Level
| X | X |
| 0c
12 | Track 5 LT - Mute (>0 mutes trk)
| X | X |
| 0d
13 | Track 6 CP - Mute (>0 mutes trk)
| X | X |
| 0e
14 | Track 7 RS - Mute (>0 mutes trk)
| X | X |
| 0f
15 | Track 8 CB - Mute (>0 mutes trk)
| X | X |
| 10
16 | Track 5 LT - Machine parameter 1
| X | X |
| ..
.. | ...
| 27
39 | ...
|
| 28
40 | Track 6 CP - Machine parameter 1
| X | X |
| ..
.. | ...
| 3f
63 | ...
|
| 48
72 | Track 7 RS - Machine parameter 1
| X | X |
| ..
.. | ...
| 5f
95 | ...
|
| 60
96 | Track 8 CB - Machine parameter 1
| X | X |
| ..
.. | ...
| 77 119 | ...
+---------+------------------------------------+-----+-----+
| hex dec | Parameter
| Trn | Rec |
|---------+------------------------------------+-----+-----+
| 08
08 | Track 13 M1 - Level
| X | X |
| 09
09 | Track 14 M2 - Level
| X | X |
| 0a
10 | Track 15 M3 - Level
| X | X |
| 0b
11 | Track 16 M4 - Level
| X | X |
| 0c
12 | Track 13 M1 - Mute (>0 mutes trk) | X | X |
| 0d
13 | Track 14 M2 - Mute (>0 mutes trk) | X | X |
| 0e
14 | Track 15 M3 - Mute (>0 mutes trk) | X | X |
| 0f
15 | Track 16 M4 - Mute (>0 mutes trk) | X | X |
| 10
16 | Track 13 M1 - Machine parameter 1 | X | X |
| ..
.. | ...
| 27
39 | ...
|
| 28
40 | Track 14 M2 - Machine parameter 1 | X | X |
| ..
.. | ...
| 3f
63 | ...
|
| 48
72 | Track 15 M3 - Machine parameter 1 | X | X |
| ..
.. | ...
| 5f
95 | ...
|
| 60
96 | Track 16 M4 - Machine parameter 1 | X | X |
| ..
.. | ...
| 77 119 | ...
MIDI base channel + 2:
+---------+------------------------------------+-----+-----+
| hex dec | Parameter
| Trn | Rec |
|---------+------------------------------------+-----+-----+
| 08
08 | Track 9 CH - Level
| X | X |
| 09
09 | Track 10 OH - Level
| X | X |
| 0a
10 | Track 11 RC - Level
| X | X |
| 0b
11 | Track 12 CC - Level
| X | X |
| 0c
12 | Track 9 CH - Mute (>0 mutes trk) | X | X |
| 0d
13 | Track 10 OH - Mute (>0 mutes trk) | X | X |
| 0e
14 | Track 11 RC - Mute (>0 mutes trk) | X | X |
| 0f
15 | Track 12 CC - Mute (>0 mutes trk) | X | X |
| 10
16 | Track 9 CH - Machine parameter 1
| X | X |
| ..
.. | ...
| 27
39 | ...
|
| 28
40 | Track 10 OH - Machine parameter 1 | X | X |
| ..
.. | ...
| 3f
63 | ...
|
| 48
72 | Track 11 RC - Machine parameter 1 | X | X |
| ..
.. | ...
| 5f
95 | ...
|
| 60
96 | Track 12 CC - Machine parameter 1 | X | X |
| ..
.. | ...
| 77 119 | ...
B-2
Appendix B: MIDI CONTROL REFERENCE
Appendix C:
SYSEX
REFERENCE
This appendix lists all Machinedrum SPS-1 MKII/SPS-1UW MKII SYSEX
messages available for external control.
Conventions:
SYSEX kit sysex dump:
Data printed with a $ sign is written in hexadecimal format.
Data printed with a % sign is written in a binary bitfield
format.
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$52 | Kit dump ID
... | Kit data bytes
$f7 | SYSEX end
-------------------------Machinedrum SYSEX messages
-------------------------All SYSEX messages start with this sequence.
MIDI Byte | Purpose
------------+---------------------------$f0 | SYSEX Start
$00 | Europe/USA ID
$20 | Europe ID
$3c | Elektron ESI ID
$02 | Machinedrum SPS-1 ID
$00 | Base channel (Padding)
A complete SYSEX message looks like this:
$f0,$00,$20,$3c,$02,$00,command,...,$f7
SYSEX kit request:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$53 | Kit dump request ID
%00aaaaaa | Send kit number %aaaaaa (0 to 63) by sysex
$f7 | SYSEX end
SYSEX unused:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$54 | None
$f7 | SYSEX end
SYSEX global settings sysex dump:
SYSEX set current kit name:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$50 | Global settings dump ID
... | Global setting data bytes
$f7 | SYSEX end
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$55 | Set current kit name ID
... | 16 bytes ASCII (7-bit)
$f7 | SYSEX end
SYSEX global setting dump request:
SYSEX set active global setting:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$51 | Global setting dump request ID
%0000aaaa | Send global setting %aaaa (0 to 7) by sysex
$f7 | SYSEX end
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$56 | Set active global setting ID
%0000aaaa | Set global pos %aaaa (0 to 7) as active
$f7 | SYSEX end
C-1
|108
|109
|110
|111
SYSEX load pattern:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$57 | Load pattern ID
%0aaaaaaa | Load pattern %aaaaaaa (0 to 127)
$f7 | SYSEX end
MID-13
MID-14
MID-15
MID-16
|
|
|
|
If c = 1 the numbers below apply
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
SYSEX load kit:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$58 | Load kit ID
%00aaaaaa | Load kit %aaaaaa (0 to 63)
$f7 | SYSEX end
SYSEX save kit:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$59 | Save kit ID
%00aaaaaa | Save kit to pos %aaaaaa (0 to 63)
$f7 | SYSEX end
ROM-01|
ROM-02|
ROM-03|
ROM-04|
ROM-05|
ROM-06|
ROM-07|
ROM-08|
ROM-09|
ROM-10|
ROM-11|
ROM-12|
ROM-13|
ROM-14|
ROM-15|
ROM-16|
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
ROM-17|
ROM-18|
ROM-19|
ROM-20|
ROM-21|
ROM-22|
ROM-23|
ROM-24|
ROM-25|
ROM-26|
ROM-27|
ROM-28|
ROM-29|
ROM-30|
ROM-31|
ROM-32|
32
33
34
35
37
38
39
40
RAM-R1|
RAM-R2|
RAM-P1|
RAM-P2|
|
RAM-R3|
RAM-R4|
RAM-P3|
RAM-P4|
|
|
|
|
|
|
|
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
ROM-33
ROM-34
ROM-35
ROM-36
ROM-37
ROM-38
ROM-39
ROM-40
ROM-41
ROM-42
ROM-43
ROM-44
ROM-45
ROM-46
ROM-47
ROM-48
SYSEX set track routing:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$5c | Set track routing ID
%0000aaaa | Route track %aaaa (0 to 15)...
%00000bbb | ...to output specified by %bbb
$f7 | SYSEX end
SYSEX set midi note to track mapping:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$5a | Set midi note mapping ID
%0aaaaaaa | Associate note %aaaaaaa ($0=C0)...
%0000bbbb | ...with track %bbbb (0 to 15)
$f7 | SYSEX end
b:0
b:1
b:2
b:3
b:4
b:5
b:6
, OUTPUT A
,
B
,
C
,
D
,
E
,
F
,
MAIN (stereo pair A/B)
SYSEX assign machine:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$5b | Load machine ID
%0000aaaa | Select track %aaaa (0 to 15)...
%0bbbbbbb | ...and assign machine %bbbbbbb number (see
| list below)
%0000000c | 0 = SPS-1, 1 = SPS-1UW (optional parameter)
%000000dd | 0 = init synthesis, 1 = init synthesis +
| effects, 2 = init synthesis + effects +
| routing (optional parameter)
$f7 | SYSEX end
SYSEX set Rhythm Echo parameter:
00
01
02
03
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$5e | Set reverb parameter ID
%00000aaa | Target parameter %aaa (0 to 7)
%0bbbbbbb | Set value to %bbbbbbb (0 to 127)
$f7 | SYSEX end
GND-EMPTY
GND-SIN
GND-NS
GND-IM
64
65
66
67
68
69
70
71
72
C-2
P-I-BD
P-I-SD
P-I-MT
P-I-ML
P-I-MA
P-I-RS
P-I-RC
P-I-CC
P-I-HH
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
16
17
18
19
20
21
22
23
24
25
26
27
28
TRX-BD
TRX-SD
TRX-XT
TRX-CP
TRX-RS
TRX-CB
TRX-CH
TRX-OH
TRX-CY
TRX-MA
TRX-CL
TRX-XC
TRX-B2
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
32
33
34
35
36
37
38
39
|
|
|
|
|
|
80
81
82
83
84
85
INP-GA
INP-GB
INP-FA
INP-FB
INP-EA
INP-EB
| 96
| 97
| 98
| 99
|100
|101
|102
|103
|104
|105
|106
|107
EFM-BD
EFM-SD
EFM-XT
EFM-CP
EFM-RS
EFM-CB
EFM-HH
EFM-CY
MID-01
MID-02
MID-03
MID-04
MID-05
MID-06
MID-07
MID-08
MID-09
MID-10
MID-11
MID-12
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
|112
|113
|
|
|
|
|
|
|120
|121
|122
|123
E12-BD
E12-SD
E12-HT
E12-LT
E12-CP
E12-RS
E12-CB
E12-CH
E12-OH
E12-RC
E12-CC
E12-BR
E12-TA
E12-TR
E12-SH
E12-BC
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CTR-AL |
CTR-8P |
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$5d | Set delay tab parameter ID
%00000aaa | Target parameter %aaa (0 to 7)
%0bbbbbbb | Set value to %bbbbbbb (0 to 127)
$f7 | SYSEX end
SYSEX set Gate box parameter:
SYSEX set the EQ parameter:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$5f | Set eq parameter ID
%00000aaa | Target parameter %aaa (0 to 7)
%0bbbbbbb | Set value to %bbbbbbb (0 to 127)
$f7 | SYSEX end
SYSEX set Dynamix parameter:
CTR-RE
CTR-GB
CTR-EQ
CTR-DX
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$60 | Set dynamics parameter ID
%00000aaa | Target parameter %aaa (0 to 7)
%0bbbbbbb | Set value to %bbbbbbb (0 to 127)
$f7 | SYSEX end
Appendix C: SYSEX REFERENCE
SYSEX pattern dump request:
SYSEX set tempo:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$61 | Set tempo ID
%0aaaaaaa | Upper bits
%0bbbbbbb | Lower bits
$f7 | SYSEX end
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$68 | Pattern request ID
%0aaaaaaa | Send pattern %aaaaaaa
$f7 | SYSEX end
Note: Tempo = %aaaaaaabbbbbbb / 24, max 300 BPM, min 30 BPM
SYSEX song dump:
SYSEX set LFO:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$62 | Set LFO ID
%0aaaabbb| %aaaa=LFO number (0 to 15), %bbb=parameter
| number (0-7)
%0ccccccc | parameter value
$f7 | SYSEX end
Note: You can also use control change to set LFO; speed,
amount & shapemix.
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$69 | Song dump ID
... | Song data bytes (see separate documentation)
$f7 | SYSEX end
SYSEX song request:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$6a | Song request ID
%000aaaaa | send song %aaaaa (0 to 31)
$f7 | SYSEX end
SYSEX unused:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$63 | None
$f7 | SYSEX end
SYSEX reset midi note map:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$64 | Reset midi note map to Elektron’s mapping
$f7 | SYSEX end
SYSEX set receive position for dump:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$6b | Receive position ID
%000aaaab | receive pos on type 0001=global 0010=kit
| 0100=pattern 1000=song
%0ccccccc | to b=0 => pos ccccccc, b=1 original position
%0ddddddd | for ddddddd sysexes of this type
$f7 | SYSEX end
Note: Same as setting the receive parameters in the
SYSEX menu.
SYSEX set trig group:
SYSEX load song:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$65 | Set trig group ID
%000aaaa | Trigger track %aaaa (0 to 15)
%000bbbb | track %bbbb (0 to 15) to be triggered
$f7 | SYSEX end
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$6c | Load song ID
%000aaaaa | Load song %aaaaa (0 to 31)
$f7 | SYSEX end
SYSEX save song:
SYSEX set mute group:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$66 | Set mute group ID
%000aaaa | Mute control track %aaaa (0 to 15)
%000bbbb | track %bbbb (0 to 15) to be muted
$f7 | SYSEX end
SYSEX pattern dump:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$67 | Pattern dump ID
... | Pattern data bytes (see separate
| documentation)
$f7 | SYSEX end
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$6d | Save song ID
%000aaaaa | Save song to position %aaaaa (0 to 31)
$f7 | SYSEX end
SYSEX status request:
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$70 | Request status ID
%00aaaaaa | Status for parameter %aaaaaa (see list below)
$f7 | SYSEX end
0x01
0x02
0x04
0x08
0x10
0x20
Appendix C: SYSEX REFERENCE
Current
Current
Current
Current
Current
Current
global slot (0 to 7)
kit number (0 to 63)
pattern number (A1=0, A2=1, ... B1=16, ...)
song number (0 to 31)
sequencer mode (pattern mode=0, song mode=1)
lock mode (classic=0, extended=1)
C-3
SYSEX set status:
MIDI Byte
| Purpose
------------+---------------------------(SYSEX init)|
$71 | Set status ID
%00aaaaaa | Set parameter %aaaaaa to ...
%0bbbbbbb | ... value %bbbbbbb
$f7 | SYSEX end
0x01
0x02
0x04
0x08
0x10
0x20
0x22
Current
Current
Current
Current
Current
Current
Current
global slot (0 to 7)
kit number (0 to 63)
pattern number (A1=0, A2=1, ... B1=16, ...)
song number (0 to 31)
sequencer mode (pattern mode=0, song mode=1)
lock mode (classic=0, extended=1)
track (0 to 15)
SYSEX status response:
MIDI Byte
| Purpose
------------+---------------------------(SYSEX init)|
$72 | Status response ID
%00aaaaaa | Parameter %aaaaaa has ...
%0bbbbbbb | ... value %bbbbbbb (see list below)
$f7 | SYSEX end
0x01
0x02
0x04
0x08
0x10
0x20
0x22
Current
Current
Current
Current
Current
Current
Current
global slot (0 to 7)
kit number (0 to 63)
pattern number (A1=0, A2=1, ... B1=16, ...)
song number (0 to 31)
sequencer mode (pattern mode=0, song mode=1)
lock mode (classic=0, extended=1)
track (0 to 15)
TURBOMIDI PROTOCOL SYSEX DESCRIPTION
All TurboMIDI SYSEX messages start with this sequence:
MIDI Byte | Purpose
------------+---------------------------$f0 | SYSEX Start
$00 | Europe/USA ID
$20 | Europe ID
$3c | Elektron ESI ID
$00 | Generic Elektron product ID
$00 | Base channel (Padding)
SYSEX turbomidi speed negotiation (master)
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$12 | Speed negotiaton ID
%0000aaaa | Speed 1 value
%0000bbbb | Speed 2 value
$f7 | SYSEX end
SPEED1 >= SPEED2 (= if certified)
SPEED1, SPEED2 = 1 requires no handshaking
SYSEX turbomidi speed acknowledgement (slave)
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$13 | Speed acknowledgment ID
$f7 | SYSEX end
Acknowledge sent upon SPEEDNEG, always sent at 1xMIDI_SPEED
After speed acknowledgement is received SPEED1 is set on
both the master and slave device
SYSEX turbomidi speed test (master)
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$14 | Speed test (master) ID
$55 |
$55 |
$55 |
$55 |
$00 |
$00 |
$00 |
$00 |
$f7 | SYSEX end
Before the speedtest the master should allow the slave some
breathing by sending 16 0x00 bytes to allow setting of speed
and resetting of UART
A complete SYSEX message looks like this:
SYSEX turbomidi speed result (slave)
$f0,$00,$20,$3c,$00,$00,command,...,$f7
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$15 | Speed test (result) ID
$55 |
$55 |
$55 |
$55 |
$00 |
$00 |
$00 |
$00 |
$f7 | SYSEX end
SYSEX turboMIDI speed test 2 (master)
SYSEX turbomidi speed request
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$10 | Speed request ID
$f7 | SYSEX end
SYSEX turbomidi speed answer
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$11 | Speed answer ID
%aaaaaaaa | bit 0 = speed 2, bit 1, = speed 3.3...
%00000bbb | bit 0 = speed 13.3x, bit 1 = speed 16x,
| bit 2 = speed 20x
%cccccccc | contains certified speed bits
%00000bbb | contains certified speed bits
$f7 | SYSEX end
C-4
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$16 | Speed test 2 (master) ID
$f7 | SYSEX end
Appendix C: SYSEX REFERENCE
SYSEX turboMIDI speed result 2 (slave)
MIDI Byte | Purpose
------------+---------------------------(SYSEX init)|
$17 | Speed test 2 (result) ID
$f7 | SYSEX end
After reception of “speed result 2” SPEED2 is set on both
the master and slave device.
then active sensing is lost for more than 300ms the device
will revert to normal MIDI speed.
Negotiation Timing:
Length of master timeouts: 30 ms minimum
Length of slave timeouts: 15ms minimum, 25 ms maximum
The timeout is for a byte, not a message, a message could
take 15xN ms to reach the slave.
Possible Speed and Max Speed parameters:
SPEED
1
2
3
4
5
6
7
8
(9)
(10)
(11)
| x 31.25 kbit
|
1
|
2
|
3.33
|
4
|
5
|
6.66
|
8
|
10
|
13.3
|
16
|
20
|
|
|
|
|
|
|
|
|
|
|
|
Values within parentheses are not supported
Active sensing:
Active sensing should be sent from any device supporting
Turbo MIDI whenever a higher speed is used
(TM-1 approx 150ms between).
If a Turbo MIDI device receives active sensing and
Appendix C: SYSEX REFERENCE
C-5
C-6
Appendix C: SYSEX REFERENCE
INDEX
A
ACCENT 45
AMPLITUDE MODULATOR 22
B
BASE CHANNEL 58
C
CLASSIC MODE 35
CLEAR
Accent 46
Kit 17
Lfo 34
Machine 20
Parameter locks 40
Pattern 44
Sample 71
Slide 50
Song 56
Song row 53
Swing 47
Track 41
Track page 42
COMPRESSOR MASTER EFFECT 31
CONNECTING THE UNIT 7
COPY/PASTE
Accent 46
Kit 16
Lfo 34
Machine 19
Note 40
Pattern 43
RAM machine 71
Sample 71
Slide 50
Song 56
Song row 53
Swing 47
Track 41
Track page 42
D
DELAY
Delay send 26
Rhythm echo delay 29
DISTORTION 25
INDEX
E
EARLY START UP MENU 79
EDIT
Kit 17
Lfo 32
Machine 21
Pattern 37
Song 52
ELECTRICAL SPECIFICATIONS 82
EMPTY RESET 79
EQ
Master effect eq 30
Track eq 23
EXTENDED MODE 35
EXTERNAL CONTROL
Control in 76
Sync 75
Tempo in 76
Trigging 63
F
FACTORY RESET 79
FILTER 23
G
GLOBAL SETTINGS 57
Control 58
File 63
Routing 62
Sync 75
GRID COMPOSING
Parameter locks 47
GRID RECORDING 39
K
KIT
Assembly 17
Machine preview 18
Trig and mute relations 18
L
LCD USER INTERFACE 9
LFO’s 32
LIVE RECORDING 39
Parameter locks 48
LOAD
Kit 14
Song 51
LOCAL CONTROL 60
M
MAP EDITOR 59
MASTER EFFECTS
1
Dynamix dynamics processor 31
Gate box reverb 30
Master eq 30
Rhythm echo delay 29
MECHANICAL SETTINGS 61
MIDI SETTINGS 58
Base channel 58
Local control 60
Map editor 59
Program change 61
Turbo menu 57
MUTE
Song 55
Track 44
O
OS UPGRADE
Receive upgrade 79
Send upgrade 81
P
PAN 26
PARAMETER EDITING 21
PARAMETER LOCKS 47
Parameter slides 49
PATTERN CHAINING 37
PATTERN MODE 37
Grid recording 39
Live recording 39
Pattern chaining 37
Pattern tweaking 37
PATTERN SEQUENCER 35
POWER SUPPLY SPECIFICATIONS 6
PREVIEW
Machine 18
Sample 71
PROGRAM CHANGE 61
R
RACK MOUNT KIT 7
REVERB
Gate box 30
Reverb send 26
ROUTING 62
Output 62
ROUTING PAGE 25
Distortion 25
Lfo control 27
Pan 26
Reverb send 26
Volume 25
2
INDEX
S
SAMPLE MANAGER 70
Erase samples 75
Original place sample receive 74
Preview sample 71
Send samples 74
Specific place receive 73
SAMPLE RATE REDUCER 24
SAMPLE RECEIVE
General sample receive 72
Original place 74
Specific place 73
SAVE
Kit 15
Song 56
SCALE SETUP 38
SLIDES 49
SOFT RESET 79
SONG MODE 51
Jumps 55
Loops 54
Mutes 55
Offset and lengths 54
Song halt 55
Transport 54
STEREO MASTER EFFECT SYSTEM 28
SWING 46
SYNC 75
Control in 76
Control out 78
Tempo in 76
Tempo out 77
SYSEX RECEIVE 66
Original place 68
Specific place 68
Verify 69
SYSEX SEND 64
All sysex send 65
Global sysex send 66
Kit sysex send 66
Pattern + Kit sysex send 66
Song + Pattern + Kit 66
Song +Pattern + Kit sysex send 66
T
TECHNICAL INFORMATION 82
TEMPO 36
Sending MIDI clock 77
Tap tempo 36
TRACK EFFECTS 22
Amplitude modulator 22
Machine 21
Parameter locks 41
Pattern 43
Sample 71
Song 56
Song row 53
Swing 47
Track 42
Track copy 41
Track page 42
Eq 23
Filter 23
Sample rate reducer 24
TRIG 63
TURBO MENU 57
U
UNDO
Accent 46
Clear track 42
Clear track page 43
Kit 16
Lfo 34
INDEX
V
VOLUME 25
3
4
INDEX
">