USER MANUAL

USER MANUAL
USER MANUAL
for
UP-02D
ultrasonic nebulizer
0197
SANASOL
Verz. 01.
1
GENERAL INFORMATION
Thank you for choosing SANASOL’s device. The UP-02D ultrasonic medicine vaporizer was
developed for vaporizing water solvent medication, medicinal waters and physiological saline solution
for infants, until they will be 2 years old. The arising aerosol gets into the respiratory-tracts with the
help of the inhalation hood.
The vaporization of the fluid is performed by a piezo-ceramics, with the help of interference liquid
and a vaporizing membrane. The size of the generated particle makes it possible that the medicine
gets even into the bronchus.
The vaporization of medication is very economical, the device works efficiently until the last drop.
The device is suitable for the treatment of bronchitis, asthma bronchiale, laryngitis, pseudocroup,
mucoviscidosis etc., or to prevent pneumoconiosis.
While the using the constant watch of an adult is required!
Before the use of the device, read carefully this User’s Manual, and keep the ones written in there
while using it, in order for that your device can serve the longer.
With question, suggestion or complaint, turn to us with trust.
Zalaegerszeg, 15rd May, 2008.
Gábor Németh, Executive Director
2
I. CONSTRUCTION OF THE DEVICE
The UP-02D ultrasonic personal nebulizer consists of three main parts:
1. The vaporizing unit
2. Network adapter
3. Inhalation hood
3
The vaporizing unit consists of the following parts:
A vaporizer house
B vaporizer cap
C ventilator
On the vaporizer house you can find:
¾ The operating button, (1)
¾ The vaporizer insertion made from silicone rubbery
(2), and on its base you can find
¾ The vaporizer membrane (3)
You can find on the removable vaporizing cap the opening of
the suction house(4) and the air-inlet bores (5).
4
The hood consists of the following parts:
• Transparent hood – The hood consists of a truss made from plastic and a plastic foil, which covers it.
• Tube leading the aerosol in– This tube can be set up in every direction, and ensures so that in the
vaporizer arisen aerosol gets directly into the infant’s nose and mouth.
The hood
Legs
Transparent plastic cover
Openable part
Tube leading the aerosol in
Adjuster head for the suction house
Tube leading the aerosol in
Silicone rubbery drop-catcher
Suction house
5
II. FIRST INSTALLATION OF THE DEVICE
Interference liquid (distilled water) between the piezo ceramic and the vaporizing insertion is required for the working of the
vaporizer. The manufacturer fills up the device during the production. This inserted liquid may decrease during the use and
the storage. Since there can elapse a notable period between the manufacture and the use, so it can happen that this liquid
level drops off already before the first use. Therefore at the first use check the factory filled liquid’s presence. If the level does
not reach the vaporizing membrane on the bottom of the vaporizing insertion, you have to do the filing up of the device
according to instructions written in Chapter IV (pages 9 and 10).
NOTICE!
The pushbutton is continuously lighting after it was connected to the network. If the liquid level drops so much, that it would
endanger the functioning, the controlling electronics will disable the functioning, which is shown by the continuously flicker of
the pushbutton after it was connected to the network. In such cases the device can be only used again after it was filled up
with interference liquid.
The device has to be disinfected according to section V. (page 12) before the first
use!
With the applied vaporizer membrane you can vaporize any kind of, water solvent medicine.
6
III. THE USE OF DEVICE
1. Grab the top of the hood and open the legs ① one by one. The opened, and fixed position which is
indicated by a click.
2. Place the silicone drop-catcher ⑥ onto the end of the tube leading the aerosol in
⑤ and with your finger push it into the tube, according to the figure.
3. Insert the tube leading the aerosol in ⑤ into the opening on the hood’s top.
4. Take off the cap of the vaporizing unit.
5. Pour the medicine or liquid to be vaporized into the vaporizer insertion (max. 10 ml).
6. Put the cap back on the lower part of the vaporizing unit.
7. Flip the ventilator to the cap and connect the ventilator into the socket.
8. Connect the adapter first to the vaporizing unit, then to the network.
9. Connect the suction house ⑦ to the adjuster head ④according to the figure.
7
11. Insert the adjuster head ④ to the tube leading the aerosol in ⑤. At the
inserting pay attention to that the little protruding part on the adjuster head
④ should enter in one of the cuts on the side of the tube leading the
aerosol in ⑤.
12. Place the hood on the baby so that the openable part should be into the
direction of its body.
13. Posture the tube leading the aerosol in 4 so that its end should be
approximately 5 centimetres far from the baby’s nose, mouth.
14. Insert the suction house’s other end into the opening of the vaporizer device.
15. By pressing the pushbutton of the vaporizer device you can start the
treatment.
Pressing the pushbutton again for a short time the vaporization will stop. The vaporization automatically stops
also after 10 minutes are over. If the liquid to be vaporized is not consumed, or you would like to continue the
treatment after filling it up again, the vaporization can started again by pressing the pushbutton repeated for a
short time.
8
Important information and warnings relating to the use of the device
¾
¾
¾
¾
¾
Only by the doctor recommended medicine, and only in the prescribed dilution can be vaporized.
The device contains small sized components too. At dissembling keep them on such places, where the
baby could not reach it.
The vaporizing unit and the hood should be cleaned after each use. The cleaning process can be found
in the Section V (page 11). (Occasionally you can leave the unused medicine in the device until tthe next
use this does not damage the device.)
If the level of the interference liquid in the vaporizing unit drops so much that the vaporizing membrane of
the vaporizing insertion already doesn’t reach into it, the interference liquid has to be refilled. Refilling
has to be made as it is written in Chapter IV (page 9).
During the use the vaporizing insertion becomes worn due to the ultrasonic effect (small cracks appear in
the material of the vaporizing membrane in the form of white discolouration on the surface of the
membrane). This causes the reduction of the vaporizing performance in this case the vaporizing
insertion has to be replaced. Replacement must be made as written in the Chapter IV (page 8).
Do not operate the device with removed cap, because the device splashes the
medication
and the ultrasound – if you touch into the fluid – can cause painful injury.
D O N O T O P E R A T E T H E D E V I C E W ITH BROKEN OR DAMA G ED COVER!
If there would be any problem in connection with using the device, before turning to the service,
look as written in the Chapter IX (page 15).
9
IV. REFILLING OF THE INTERFERENCE LIQUID, REPLACEMENT OF THE VAPORIZING INSERTION
If the vaporizing insertion becomes worn during use due to the ultrasonic effect (white discolouration can be seen
on the rubbery membrane surface of the vaporizer), or the interference liquid’s level in the vaporizing unit so
much that the vaporizing insertion made from silicone rubbery doesn’t reach into it, the device has to be
disassembled, and the vaporizing insertion has to be replaced, and the interference liquid has to be refilled. The
replacement and the refill have to be done in the following way:
1. Insert the blank attached
to the device into the slots
on the inner side of the
fixing ring of the vaporizing
insertion.
2. Screw out the
ring anticlockwise.
3. If the fixing ring
has not lifted out
the vaporizing
insertion, remove it
from its place.
4. Pour out the fluid, which can be found even
there.
5. If it is needed clean the inner surface of the
tank.
Do the cleaning with a wet or alcoholic
cloth, do not use any other agent!
10
6. Fill up the tank with
25 ml distilled water.
For the refilling it is
recommended to use
a syringe.
Attention!
Do not use a needle in the syringe during
refilingl to avoid damages to the vaporizing
insertion!
Be careful not to touch the golden surfaced
ceramic with a hard object!
7. Replace the
vaporizing insertion.
If the old one is
worn, replace it with
a new one.
8. Screw back the
fixing ring, and tighten
it with the attached
blank.
ATTENTION! The lifetime of the vaporizing
insertion is significantly reduced, if the device is
run empty, without fluid to be vaporized. So if the
flui, medicined to be vaporized, i is out, do not
use the device further!
It is recommended to perform the sterilization
process written in the Chapter V (page 12)
during the replacement of the vaporizing
insertion and the refill ing of the interference
liquid.
The replacement of the worn vaporizing insertion
is provided by the manufacturer. See our
availability on the back cover.
11
V. CLEANING AND DISINFECTION
THE CLEANING AND DISINFECTION OF THE DEVICE IS EXCLUSIVELY ALLOWED TO BE
PERFORMED IN A STAGE IF IT IS DISCONNECTED, ANNEALED FROM THE MAINS POWER!
Cleaning (After every use)
¾
¾
¾
¾
¾
¾
Flip the ventilator from the cap before you start the cleaning.
Pour out the fluid, which remained in the device as you take off the cap.
Rinse the vaporizing insertion with clean water.
Wash the plastic components with running water.
Do the cleaning of the ventilator and the hood only with wet cloth.
Placing the cleaned device and its accessories onto clean surface dry them on air.
Wash the air filter of the ventilator (if it is needed) occasionally with running water.
The filter should be replaced only after it is completely dried.
Change the worn or damaged filter. (Is available at the manufacturer.)
A blocked filter reduces the air transport!
Do not use other agents (petrol, solvent etc) for the cleaning!
Take care that no water should get into connectors of vaporizing unit, and into the ventilator!
DURING THE CLEANING AND THE DISINFECTION, TAKE CARE NOT TO TOUCH THE RUBBERY MEMBRANE WITH A
SHARP OJECT, BECAUSE THAT COULD CAUSE THE DAMAGE OF THE MEMBRANE!
12
Disinfecting (as occasion requires)
Before the first use, or after a long storage, and to avoid re-contamination, the device has to be disinfected
occasionally. The way of the disinfecting:
Make an antiseptic solution from any cold antiseptic (eg. BARRYCIDAL 22) available at a pharmacy –on the
way prescribed for the agent-.
¾ Clean up the external surface of the vaporizer unit and the hood and the ventilator with a disinfectant, after it
clean it with clear water wetted cloth.
¾ Fill up the vaporizing membrane of the vaporizing unit with the solution, and soak it for the agent’s prescribed
contact time.
¾ Finishing the disinfection from the vaporizing insertion flush out extensively the antiseptic liquid with clear
water.
¾ Soak also the plastic and rubbery components into the antiseptic solution for the agent’s prescribed contact
time.
¾ The disinfected components have to be also flushed extensively with running water.
¾ Do over the network adapter (if is needed) occasionally with an antiseptic, mildly wet tissue.
Dry the so disinfected device and its accessories –placing them onto clear surface – on air.
¾
¾
¾
During the disinfection, take care not to let any water into the connectors of the vaporizing unit, and the
ventilator!
If water would get into the adapter during the cleaning or the disinfection (for example if it fell into water by accident),
you should not try to dry out the device, but send it promptly to the service. The device could be in that case damaged,
or could cause an electric shock. You MUSTN’T attach it again to the network!
13
VI. MAIN TECHNICAL DATAS
Voltage:
Performance:
Adaptor:
Vaporizing frequency:
UP-02, UP02 B
UP-02C
Particle size:
UP-02, UP-02B
UP-02C
Filling amount:
24 V DC
14 W
input: 100-240V AC
50/60 Hz 0,45A max
output: 24V DC 750 mA
2,4 MHz
Vaporizing output (measured with distilled
water, minimum)
UP-02:
UP-02B, UP-02C,
1 ml/min
Operating time/pause:
30/30 perc
Weight
vaporizing unit:
151 g
adapter:
110 g
Brutto:
261 g
Size:
110 x 50 x50mm
°
Storage temperature:
0 - +35 C
5 µ MMD
10 ml
Do not store the device permanently at temperatures under 0 C°, because the distilled water in the vaporizer
freezes, and this makes the device temporarily unserviceable!
The data, guidelines referring to the device’s electromagnetic immunity, output of the jam, and the
recommended protecting distances and the manufacturer’s statements can be found on the website
of the SANASOL Ltd. (www.sanasol.hu) among the downloads.
Manufacturer: SANASOL Kft.
u.13. H-8900 Zalaegerszeg, HUNGARY
: +36 92-511-381 Fax: +36 92-511-382
Skype: sanasol2
web: www.sanasol.hu
E-mail: [email protected]
Wlassics Gyula
14
VII. CONTENT OF THE PACKAGE
1. Vaporizing unit
2. Network adapter *
3. Ventilator
4. Hood
5. Cardboard box
6. User’s Manual
* Manufacturer of the adapter: GlobTek Inc.
15
IX. WHAT SHOULD I IF...
Failure symptom
Cause of the
To do
failure
The pushbutton There
is Check the presence of the interference liquid (distilled water) . Refill it if it is
is flickering after interference
needed (Chapter IV, pages 9 and 10).
it was connected liquid below the
to the network
vaporizing
insertion
Cracked ceramic If you can find the interference liquid, in that case the device is damaged, and
can only repaired in a special service.
The vaporizing The
vaporizing Check if you can see white discoloration on the vaporizing insertion’s bottom,
output of the insertion is worn on the vaporizing membrane. If yes, replace the vaporizing insertion. (Chapter
device
has
IV, pages 9 and 10)
decreased
The ceramic is If the replacement of the vaporizing insert had not solved the problem, most
worn
likely the replacement of the ceramic is required. Turn to the service.
The
device
vaporizes,
but
the
ventilator
does not rotate
The
device
vaporizes,
but
the fan does not
blow out the
aerosol.
The ventilator is
not connected
Water got into
the ventilator
Other defects
Water entered in
the air inlet ports
of the vaporizing
lid
Check if the connecting plug of the ventilator is pushed into the vaporizing unit
to the stop into the vaporizing unit.
Disconnect the fan, remove the fan, and let it dry (1 day). Try again after the fan
gets dry.
Contact the service.
Disconnect the fan, remove the fan, and remove the liquid from the air inlet
ports by blowing them out.
16
X. SYMBOLS USED ON THE DEVICE
WARNING! Read the Instruction Manual, and comply with those written in it!
B-type device
II. Class of protection against indirect contact (dual insulation)
Manufacturer
17
Declaration of conformity
Manufacturer:
Address:
Product typ:
SANASOL
SANASOL Meditechnika Kft.
Wlassics Gy. 13, H-8900 Zalaegerszeg, HUNGARY
Phone: +36 92 511 381
Fax: +36 92 511 382
e-mail: [email protected]
web: www.sanasol.hu
UP-02D Ultrasonic nebulizer
Serial number:
Class:
II.a (according to the Rule 11 of Annex IX of 93/42/ECC Directive)
We herewith declare on our sole responsibility that above product complies with the requirements of
EC Directive 93/42/EEC.
Applied standards:
Notified body:
Certificate No:
Certificate date:
Date of Issue:
For applies standards, please refer to Chapter IV.
Construction File.
TÜV Rheinland Product Safety GmbH
Am Grauen Stein, 51105 Köln (Notified Body No. 0197)
DD 60022053 0001
28. Aug. 2008.
01. Sept. 2008.
Issued by:
Managing Director
Gabor Nemeth
of
the
Technical
18
GUARANTEE
A period of 1 year for the unit after the date of purchase the proper construction, workmanship and materials of this product is
guaranteed by SANASOL. During this period of guarantee SANASOL will, without charge for labour or parts, repair or replace
the defect product or its defective parts.
The guarantee does not cover any of the following:
o
Transport costs and risk of transport.
o
Costs for repairs and/or defects resulting from repairs done by unauthorised persons. Should guarantee service be
required please apply to the retailer whom the product was purchased from for an authorised SANASOL distributor.
For the address refer to the product packaging/attached literature or to your specialised retailer. If you have difficulties
in finding SANASOL Kft., contact us for information.*
o
Periodic check-ups, maintenance and repair.
o
Failure or wear of accessories or attachments other than the main device itself, unless explicitly guaranteed above.
o
Costs resulting from non-acceptance of a claim.
o
Damages of any kind including personal caused accidentally or from misuse.
Repair or replacement under the guarantee does not give rise to any extension or renewal of the guarantee period.
The guarantee will be granted only if the complete product is returned together with the guarantee card and the original
invoice/cash ticket issued to the consumer by the retailer and customer. The guarantee card must be completed in full and
SANASOL reserves the right to refuse guarantee service if any unclear information has been given.
SANASOL Kft. becomes the owner of all exchanged parts or units.
*SANASOL Kft.
Wlassics Gy. 13., H-8900 Zalaegerszeg, Hungary
Phone: (92) 511-381
Fax: (92) 511-382
E-mail: [email protected]
19
GUARANTEE DOCUMENT
Product name: ULTRASONIC MEDICINE NEBULIZER
Type:
UP-02D
Product serial number:
Manufacturer: SANASOL Kft. Wlassics Gy u. 13. 8900. Zalaegerszeg, HUNGARY
Date of purchase: ……..day ……………….month ……... year
________________________
signature
_________________________
stamp of retailer
SERVICE:
SANASOL Kft.., 8900. Zalaegerszeg, Wlassics Gy u. 13. HUNGARY
: +36 92-511-381 Fax: +36 92-511-382
E-mail: [email protected]
Skype: sanasol2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement