Corded telephone LJ-180
User Guide
LJ-180
Please read these instructions
carefully before use and keep this
User Guide for future reference.
Contents
LJ-180
Contents
I. Introduction.........................................................................................
Telephone features...............................................................................
Function button index............................................................................
II. Getting started...................................................................................
How to connect the batteries................................................................
How to connect the handset and telephone line...................................
How to set the dial mode for your type of telephone exchange............
Wall mounting……………………………………………………………….
III. Using the telephone.........................................................................
How to set the display contrast.............................................................
How to set date and time......................................................................
Ringer volume control...........................................................................
How to select ringer melody..................................................................
2-way speaker function.........................................................................
How to make a call...............................................................................
How to receive a call.............................................................................
OUT memory........................................................................................
How to delete the OUT number............................................................
Redial function......................................................................................
Auto-redial function…………………………………………………………
Hold function.........................................................................................
Memory.......................................................................………………….
Flash function........................................................................................
How to lock telephone numbers............................................................
Alarm function.......................................................................................
“Don’t disturb” function..........................................................................
IV. Clip (Caller ID) – Calling line identification presentation.............
How to review Clip numbers.................................................................
How to delete Clip numbers..................................................................
How to make a call from the Clip memory............................................
How to set the prefix………………………………………………………..
How to set the local area code..............................................................
V. Help...................................................................................................
Important advice..................................................................................
1
2
2
3
4
4
4
4
4
5
5
5
5
6
6
6
6
7
7
7
7
8
8
9
9
9
10
11
11
11
12
12
12
13
13
I. Introduction
LJ-180
I. Introduction
Important!
Please read these instructions carefully before use and keep this User Guide for future reference.
Telephone components supplied:
telephone set (base unit + handset),
handset cord,
line cord,
user guide,
guarantee card.
Telephone features
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
12-digits, green backlit LCD display
10 two-touch number memory
CLIP(Caller ID) – calling line identification
presentation in FSK/DTMF European system
104 memory locations
telephone number review
date and time display
local area code enter
prefix
call back
Alarm-clock
Call timer
Adjustable display contrast
Date and time setting
Last number redial
30 redial number memory
2-way speaker function
2-way speaker volume switch
Pre-dial function
Flash
16 types of ringer sound selectable
(8 melody ringers)
Ringer volume control
“Don’t disturb” function
Music on hold
Tone/pulse dialing
Lock for long distance calls
Wall mounting
2
I. Introduction
LJ-180
Function button index
1. Handset hole
16. RECALL button
2. Handset loudspeaker
17.BRIGHT button
3. Base loudspeaker
18. VOLUME button
4. Wall clip
19. OUT button
5. Hook switch
20. IN USE indicator
6. RINGER LOW/HI switch
21. Keypad
7. MODE P/T switch
22. Handset microphone
8. 9V power supply socket
23. Handset sockets
9. Key socket
24. SET/HOLD button
10. LINE OUT socket
25. DEL/TIME button
11. LINE IN socket
12. LCD display
26. FLASH button
13. UP button
27. RD/ARD button
14. DOWN button
28. Base microphone
15. STORE button
29. SP-PHONE button
Note!
The line sockets LINE OUT, LINE IN, the RINGER LOW/HI switch, the MODE P/T switch, the DC9V
socket, the handset sockets are located on the side of the base unit. In addition, on the side of the base unit,
is the socket for blocking telephone numbers.
1
2
3
45
6
7
8
9
10
11
12
13
14
15
16
UP
DOWN
STORE
SET/HOLD
RECALL
BRIGHT
OUT
DEL/TIME
1
4
7
VOLUME
2
5
8
0
ABC
GHI
JKL
PQRS
TUV
*
FLASH
22
23
24 25
RD/ARD
26
27
3
3
6
9
#
DEF
MNO
17
18
19
20
WXYZ
SP-PHONE
28 29
21
II. Getting started
LJ-180
II. Getting started
How to connect the batteries
Remove the cover of the battery compartment on the underside of the base unit.
Fit three 1,5V AA batteries,
Replace the battery compartment cover.
Note!
Instead of batteries, the adaptor to the DC9V socket, which is placed on the side of the base unit can be
connected. The parameters of the adaptor must be as follows:
inside voltage –
UIN = 230V, f =50 Hz
outside voltage–
Uout = 9V DC
current
Ioutmin = 100 mA
standard plug (Φ=2.1 mm)
with „-” inside.
Adaptor is not in complete!
How to connect the handset and telephone line
Plug one end of the coiled handset cord into the handset and the other end into the
socket on the side of the telephone.
Insert the base unit’s telephone line plugs into the PTT wall socket and telephone socket
LINE IN as shown on the illustration.
Note!
The telephone is equipped with two line sockets. These sockets are connected in parallel. It does not matter,
where the telephone line and second telephone are connected.
How to set the dial mode for your type of telephone exchange
These are two different modes a telephone can use to communicate with the local exchange.
Modern telephone exchanges accept TONE dialling, but some older exchanges accept only
PULSE dialling. This telephone is capable of either type of dialling- but if your local telephone
exchange is a modern one that accepts TONE dialling, this is the best type to use, because:
it gives you much faster connections,
it allows you to use special functions if they are available in your area.
To set the right dial mode:
move the MODE P/T switch to T or P position.
Note!
Special functions are available only if the relevant operator services have been subscribed to.
If more information is required, please contact the office or your network provider.
Wall mounting
The wall mount brackets are located underneath the telephone base unit. The telephone can be
conveniently wall mounted near the PTT line socket.
To mount the base onto the wall:
drill two holes into the wall in the correct position, a distance of 130mm apart. Put the
screws into the wall, leaving about 5 mm free to hang the wall mounting bracket,
set the wall clip in the right position,
replace the handset on the base unit,
hang the telephone onto the screws.
YOUR TELEPHONE IS NOW READY FOR USE!!!
4
III. Using the telephone
LJ-180
III. Using the telephone
How to set the display contrast
The setting factory is 3.
To set the display contrast:
press the BRIGHT button, until the display will show the right setting for you.
Press the DEL/TIME button to return to the standby mode.
If the DEL button is not pressed, the telephone will return to standby mode after several seconds.
The setting will be stored.
How to set date and time
To set date and time:
press the SET/HOLD button. The display will show - 0 1 2 3 4 5 6 7 -.
Press the 1 button. The display will show the symbol 2004 indicating the year. The one
before last digit will be flashing.
Use the keypad to enter the right digits. For example, if you want to set the year 2007:
•
press the 0 button, the last digit will start to flash,
•
then, press the 7 button.
After setting the year, the first digit indicating the month will start to flash. Use the
keypad to enter the right digits. For example, if you want to set August:
•
press the 0 button, the next digit will start to flash,
•
then, press the 8 button.
After setting the month, the first digit indicating the day will start to flash. Use the keypad
to enter the right digits. For example, if you want to set the 27th day of month:
•
press the 2 button, the next digit will start to flash,
•
press the 7 button.
After setting the day, the first digit indicating the hours will start to flash. Use the keypad
to enter the right digits. For example, if you want to set 16.00:
•
press the 1 button, the second digit will start to flash,
•
press the 6 button.
After setting the hour, the first digit indicating the minutes will start to flash. Use the
keypad to enter the right digits. For example, if you want to set the 59th minute:
•
press the 5 button, the last digit will start to flash,
•
press the 9 button.
After entering the minutes, the telephone will return to standby mode automatically. All settings will
be stored.
Note!
♦ If incorrect buttons are pressed, the settings will not be
confirmed.
♦ During the setting, press the UP or DOWN button to move between the
digits (to choose the digit, you want to change).
Ringer volume control
The volume at which the base unit will ring for an incoming call can be adjusted.
To select the volume you prefer:
move the RING LOW/HI switch to:
LOW position– low ringing volume
or
HI position– high ringing volume.
5
III. Using the telephone
LJ-180
How to select the ringer melody
One ringer melody can be selected from among 16 ringer melodies. The settings rING 01-08
indicate the normal ringers and settings rING 09-16 indicate the melody ringers.
To select one ringer melody:
press the SET/HOLD button. The display will show - 0 1 2 3 4 5 6 7 -.
Press the 7 button. The display will show an actual setting rING 09. The ringer melody
will be played.
Press the UP or DOWN button to select the right signal (melody).
Press the SET/HOLD button to confirm the setting. The display will show the symbol
- 0 1 2 3 4 5 6 7 – again.
Press the DEL/TIME button. The telephone will return to the standby mode.
If the DEL/TIME button is not pressed, the telephone will return to standby mode after several
seconds. The setting will be stored.
Note!
The melody ringers are available only, when the batteries are placed in
the battery compartment. If there are no batteries, only the normal
ringer will sound.
2-way speaker function
The 2-way speakerphone function allows a number to be dialed, or a call to be made, without the
handset needing to be lifted. The party on the other end of the line will automatically be able to
hear and to be heard through the speaker located in the base unit of the telephone. When using
this function, the user needs to speak within a reasonable distance of the telephone microphone in
order that the microphone may pick-up voice sound. This function may also be used to make a
conference call between several parties in the same office.
Using the SP-PHONE button, the 2-way speakerphone function can be switched on/off. After
pressing the SP-PHONE button, the display will show the timer.
In addition, the VOLUME button can be used to adjust the volume of the loudspeaker.
How to make a call
To make a call:
lift the handset from the base unit
or
press the SP-PHONE button. The display will show the timer.
When the PTT on-line signal is heard, the required number should be dialed. The
number will be displayed. After several seconds, the call time counter will be switched
on.
To end your conversation, replace the handset on the base unit or press the SP-PHONE
button. The time of your last call can be displayed by pressing the OUT button (see the
chapter: ”OUT memory”)
Note!
The telephone number in the standby mode can also be entered (before lifting the handset or pressing the
SP-PHONE button).If you wish to delete the last incorrect digit, press the DEL/TIME button. If you wish to
make a call, press the BACK÷ button. The 2-way speaker function will be switched on and the number will
be dialed automatically.
How to receive a call
When the telephone rings:
lift the handset from the base unit or press the SP-PHONE button.
After completing your conversation, replace the handset on the base unit or press the
SP-PHONE button.
6
III. Using the telephone
LJ-180
OUT memory
Your telephone can store 30 the most recently dialed numbers in the OUT memory. They can be
reviewed by pressing the OUT button in standby mode. Each number may consist of up to 16
digits.
To review OUT numbers:
press the OUT button. The display shows the last number dialed.
Press the OUT button again to display the time of this call and the number of the
memory location.
Press the OUT button again. The display shows the number, stored in the lower
memory location.
Press the OUT button again to display the time of this call and the number of the
memory location.
By pressing the OUT button, the remaining numbers can be reviewed.
If the OUT button is not pressed, the telephone will return to standby mode after several seconds.
If the memory is empty, the display will show the symbol - - - End - - -.
To make a call:
press the OUT button to select the number.
Press the RD/ARD button. The 2-way speaker function will be switched on and the
number will be dialed automatically.
After the call, replace the handset on the base unit or press the SP-PHONE button.
How to delete an OUT number
To delete an individual number:
press the OUT button to select the number, to be deleted.
Press the DEL/TIME button twice. The number will be removed.
To delete the all numbers:
Press the OUT button.
Press and hold the DEL/TIME button until - - - End - - - is displayed. After several
seconds, the telephone will return to standby mode. All numbers will be removed.
Last number redial
Your telephone automatically stores the last number dialed of up to 32 digits long. This function
can be used, when the number is busy.
To redial:
lift the handset or press the SP-PHONE button.
Press the RD/ARD button. The last number will be displayed and dialed.
Autoredial function
The Autoredial function allows the last number to be redialed during the using the 2-way speaker
button. This operation can be repeated many times, until a connection is made.
To dial the number again:
press the RD/ARD button. The 2-way speaker function will be switched off briefly. After
an interval, the 2-way speaker function will be switched on and the number will be dialed
again automatically.
7
III. Using the telephone
LJ-180
Hold function
The Hold function allows music to be switched on during the conversation. After pressing the
HOLD button, the person on the other end of the line will automatically be able to hear music. This
function may be used, for example, in offices while a client is on hold.
To switch the hold music on:
inform the person on the other end of the line about a music pause.
Press the SET/HOLD button. The display will show Hold. The telephone will start to
play music.
Note!
In activating this function using the UP or DOWN button, you may select the melody you wish the caller to
hear. There are 8 melodies available, from which you can choose. These are indicated by symbols from 01
to 08.
You can replace the handset on the base. The connection will not be interrupted. The
hold music will be heard through the speaker located in the base unit of the telephone.
Lift the handset or press the SP-PHONE button to continue speaking. The Hold function
will be switched off.
Note!
If the handset is not replaced on the base, press the SET/HOLD button again to switch the hold music off.
Memory
Your telephone can store 10 telephone numbers in the two-touch memory. The number can then
be dialed by pressing two buttons. The two-touch memory locations are located under the buttons
of the keypad. Each number that is stored can have up to 16 digits.
To store a number in the memory:
press the STORE button. The display will show INPUt CodE_.
Enter the number, to be stored in the memory. The number will be displayed.
Press the STORE button a second time.
Now press one of the number buttons (0-9). This gives you the code under which your
number will be stored. The telephone will return to standby mode.
To dial a number using the memory :
lift the handset or press the SP-PHONE button.
Press the RECALL button.
Next press the appropriate code number key (0-9). The number will be displayed and
dialed.
Note!
If there is no number under the code number key, the telephone displays symbol NO COdE.
Replace the handset or press the SP-PHONE button to end the call.
Note!
1. Storing a number in the memory automatically deletes any previous number kept under the individual
code number you choose.
2. The stored numbers can be reviewed in the standby mode. To display the number from the code number
key:
press the RECALL button,
press the code number key. The number will be displayed.
8
III. Using the telephone
LJ-180
How to delete a number from one-touch and two-touch memory
During the review:
Press the DEL/TIME button twice. The number will be removed. The telephone will return to
standby mode.
Flash function
This allows various switchboard facilities such as call transfer and conference calls to be
used. Contact your communications manager or the person responsible for maintaining your
switchboard to find out what facilities are available.
The telephone allows the following values to be set: 90ms, 120ms, 180ms, 300ms, 600ms
and 1000ms
To set the right Flash value:
press the SET/HOLD button. The display will show - 0 1 2 3 4 5 6 7 -.
Press the 2 button. The display will show an actual setting. The factory setting is 600ms.
Press the UP or DOWN button to select the right value.
Press the SET/HOLD button to confirm the setting.
Press the DEL/TIME button. The telephone will return to standby mode.
If the DEL/TIME button is not pressed, the telephone will return to standby mode after several
seconds. The setting will be stored.
How to transfer a call.
To transfer a call from one internal number to another:
press the FLASH button.
Enter the number, to which you want to transfer the call.
Replace the handset on the base unit.
How to lock the telephone numbers.
The telephone can be blocked so that it is impossible to make a call beginning with the digit „0”,
for example:
a Long Distance or International call, a Party Line call, or, in the case of an office switchboard,
where the number „0” facilitates an outside line , it can block an extension number from being
used by an unauthorized person. This is an invaluable feature in the prevention of unauthorized
calls and the safeguarding of a telephone bill from unauthorized expense.
In order to use this feature the key must be placed in the lock located on the underside of the
telephone, and then turned to the required position:
“green dot” position - the telephone can be used to dial all numbers on the keypad
including „0”.
“red dot” position – the telephone can used to block all numbers.
“yellow dot” position - the telephone has the lock activated and the number „0” cannot
be dialed.
Alarm function
Your telephone may be used as alarm clock. Up to three different times may be stored
simultaneously, using the alarm function. The telephone will emit the alarm signal for 40 seconds.
To program the alarm:
1. press the SET/HOLD button. The display will show - 0 1 2 3 4 5 6 7 -.
2. Press the 5 button. The display will show AL 123.
3. Press the 1 button to set the first alarm. The display will show symbol AL 1OFF. Alarm is off.
4. Press the */. button to switch alarm on. The display will show AL 1 12-00. The first digit of
the clock will flash.
9
III. Using the telephone
LJ-180
5. Using the keypad, enter the hour and minute. For example, if you wish to set 15:37, press the
following digits 1537.
6. Press the SET/HOLD button. The display will show AL
123.
7. Press the 2 button. The display will show symbol AL 2OFF.
8. Repeat steps 4 and 5 to set the second alarm.
9. Press the SET/HOLD button. The display will show AL
123.
10. Press the 3 button, if you wish to set the third alarm. The display will show
AL 3OFF.
11. Repeat steps 4 and 5 to set the third alarm.
12. Press the SET/HOLD button. The display will show AL
123.
13. Press the SET/HOLD button once more to confirm the setting. The display will show
– 0 1 2 3 4 5 6 7 -.
14. Press the DEL/TIME button. The telephone will return to the standby mode.
If the DEL/TIME button is not pressed, the telephone will return to standby mode after several
seconds. The setting will be stored.
Note!
You do not have to set three alarms . After displaying symbol AL 123, select the alarm, you wish to set.
The alarm signal will be played every day. The alarm can be switched off by pressing the
DEL/TIME button.
Note!
The alarm will only function when the batteries are located in the battery compartment or the
base unit is connected to a power supply.
To switch the alarm off, set the AL 1OFF symbol by pressing the */. button.
„Don’t disturb” function.
Your telephone allows the ringer to be switched off.
To switch the ringer off:
press and hold the BRIGHT button, until SLEEP 0-30 is displayed. The ringer is then
switched off for 30 minutes. This is a factory setting.
To change the time, press the UP or DOWN button. Each time this button is pressed,
the setting is changed by about 30 minutes. The maximum time that the ringer may be
switched off is 23 hours and 30 minutes.
Note!
If the UP or DOWN button is not pressed within 5 seconds, the setting will be confirmed as the minimum
time (30 minutes).
Press the SET/HOLD button to confirm the setting.
Press the DEL/TIME button. The telephone returns to the standby mode and the display
shows SLEEP and clock.
Note!
a) If no further buttons are pressed, the telephone will return to standby mode after several seconds. The
settings will be stored.
b) If you have an activated CLIP service, all numbers will be stored in the memory.
c) Remember, that the flashing display also informs of incoming calls.
To switch the „Don’t disturb” function off
lift the handset or press the SP-PHONE button briefly. The telephone will return to the
standby mode.
10
IV. Clip (Caller ID)- Calling line identification presentation
LJ-180
IV. Clip (Caller ID)- calling line identification presentation
Note!
CLIP function is only available if you have subscribed to the relevant operator services or those of another
Provider. If more information is required, please contact the Customer Service Office in your area..
Your telephone displays and stores the number of the caller. The number is displayed until the UP
or DOWN button is pressed or the handset lifted. The number can be identified using the FSK
system and DTMF
The FSK system is the best to use, because:
it allows the sending of statements, which define the status of the number,
it allows the automatic setting of time and date.
The telephone can store a maximum of 104 numbers.
Together with the number, date, time and statements (symbols) are also stored. The display can
show the following symbols:
NEW- a new number is stored in the memory,
REP- the number is repeated,
- - - P - - -- the number is private and cannot be displayed,
- - - O - - - - the number is unknown and cannot be shown,
Error (- - - E- - - )- an error has occurred in sending the number.
The number is identified and stored in the following form:
for example- 0 42 1234567,
The identified number consists of:
0- prefix,
42- local area code,
1234567- number of subscriber.
Note!
If the clip memory is full, storing a new number automatically deletes the first stored number.
How to review Clip numbers
If new numbers are stored, the NEW indicator flashes. The number is displayed until the UP or
DOWN button is pressed or the handset lifted.
After displaying new numbers, the NEW symbol disappears from the display. New numbers
change their status to old numbers.
To review all numbers:
press the UP button, the display will show the number stored in the first memory
location. After next pressing the UP button, the display will show date and time.
Press the DOWN button, the display will show the number stored in the last memory
location. After next pressing the DOWN button, the display will show date and time.
Use the UP and DOWN buttons to review all numbers
Note!
If there are no numbers in the memory, after pressing one of the buttons, the display will show - - - End - - -.
How to delete Clip numbers
To delete an individual number:
press the UP or DOWN button to select the number you want to remove.
Press the DEL/TIME button twice. The number will be removed.
Using the UP, DOWN and DEL/TIME buttons the remaining numbers can be removed.
To delete all numbers:
press the UP or DOWN button.
Press and hold the DEL/TIME button, until the telephone will show - - - End - - -. After
several seconds, the telephone will return to standby mode. All numbers will be deleted.
11
IV. Clip (Caller ID)- Calling line identification presentation
LJ-180
How to make a call from Clip memory
To make a call:
press the UP or DOWN button to select the number.
Now, press the RD/ARD button. The 2-way speaker function will be switched on and the
number will be dialed automatically.
Replace the handset or press the SP-PHONE button to end the call.
Special case!
It may happen, that the number identified was stored without a prefix, which is necessary to make
long distance calls. Your telephone allows a prefix to be added at the beginning of the number
automatically. A prefix is added after pressing the RD/ARD button twice. In Poland, the prefix used
is 0.
To make a call using a number without a prefix:
press the UP or DOWN button to select the number.
Press the RD/ARD button twice. The 2-way speaker function will be switched on, the
prefix will be added and the number will be dialed automatically.
Replace the handset or press the SP-PHONE button to end the call.
How to set the prefix
To enter the prefix:
press the SET/HOLD button. The display will show - 0 1 2 3 4 5 6 7 -.
Press the 3 button. The display will show CodE - 12 -.
Press the 2 button. The display will show 0CodE - -.
Using the keypad, enter the prefix.
Press the SET/HOLD button to confirm the setting. The display will show CodE - 12 -.
Press the DEL/TIME button. The telephone will return to standby mode.
If no further buttons are pressed, the telephone will return to standby mode after several seconds.
The settings will be stored.
To delete the prefix:
press the SET/HOLD button. The display will show - 0 1 2 3 4 5 6 7 -.
Press the 3 button. The display will show CodE - 12 -.
Press the 2 button. The display will show an actual setting.
Press the */. button. The display will show symbol 0CodE - -.
Press the DEL/TIME button. The telephone will return to the standby mode.
How to set the local area code
At present, a local area code does not need to be entered to make local calls. This function can
only be used to specify local numbers. Entering a local area code in the memory removes it from
all numbers, which belong to the same area.
To enter the local area code:
press the SET/HOLD button. The display will show - 0 1 2 3 4 5 6 7 -.
Press the 4 button. The display will show ArEA - - - - -.
Using the keypad, enter the local area code.
Press the SET/HOLD button to confirm the setting.
Press the DEL/TIME button. The telephone will return to standby mode.
If no further buttons are pressed, the telephone will return to standby mode after several seconds.
The settings will be stored.
To delete the local area code:
press the SET/HOLD button. The display will show - 0 1 2 3 4 5 6 7 -.
Press the 4 button. The display will show an actual setting.
Press the */. button. The display will show symbol ArEA - - - - -.
Press the DEL/TIME button. The telephone will return to the standby mode.
12
V. Help
LJ-180
V. Help
Please read this Troubleshooting Guide in case of difficulty.
No signal in the handset:
check that the telephone is connected to the telephone line.
No dial tone:
check that the telephone is connected to the telephone line,
check that the MODE P/T switch is in the correct position.
In standby mode (when the handset is on the base unit), the display shows nothing:
check that batteries are correctly inserted into the battery compartment,
the batteries may be dead.
The telephone rings quietly or does not ring:
check that the RINGER LOW/HI switch is in the correct position.
the batteries are very low
Unable to switch on the 2-way speakerphone function:
the batteries are dead,
no batteries in the battery compartment.
No CLIP:
Clip function is not activated by your Provider.
Alarm function does not work:
check that there are batteries are in the battery compartment,
the batteries may be dead.
Important advice
Never use your telephone during a thunderstorm. Unplug it from the telephone line and
the mains socket when there are storms in your area
The telephone should not be installed near a sink, bath or shower. Electrical appliances
can cause serious injury if the user is wet or standing in water.
The telephone should be cleaned only when disconnected from the telephone PTT line.
Please clean the telephone with a soft cloth to prevent scratching.
Do not use chemical sprays or aerosols to clean the telephone.
Do not put the telephone in a wet, damp place or, in bright sunlight or where it could be
damaged.
This symbol on the products means that used electrical
and electronic products should not be mixed with general
household waste.
For proper treatment, recovery and recycling, please take
these products to designated collection points, where they
will be accepted on a free of charge basis. Alternatively,
in some countries you may be able to return your products to your local retailer upon the purchase
of an equivalent new product. Disposing of this product correctly will help to save valuable
resources and prevent any potential negative effects on human health and the environment which
could otherwise arise from inappropriate waste handling. Please contact your local authority for
further details of your nearest designated collection point.
13
Declaration of Conformity (CE)
LJ-180
DECLARATION OF CONFORMITY
Przedsiębiorstwo “DARTEL”
MANUFACTURER'S NAME:
ADDRESS:
29-100 Włoszczowa, Podlipie 26
TYPE OF PRODUCT:
Corded phone
PRODUCT NAME:
LJ-180
We inform, our products conform to the requirements of
the following Directives and Norms:
1) Radio & Telecom Terminal Equipment Directive 99/5/EEC,
2) Low Voltage Directive 73/23EEC,
norm PN-EN 60950 -1,
3) Electromagnetic Compatibility Directive (EMC) 89/336/EEC,
norm PN-EN 55022,
norm PN-EN 55024,
norms PN-EN 61000-4/-2/-3/-4/-5/-6/-8/-9/-11/.
Date:
August 2007
14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement