USER'S MANUAL
USER’S MANUAL
PODO-152
Media Player with Pedometer
For information and support, www.lenco.com
WARNINGS
•
Do not place naked flames, such as lighted candles on or near the product.
•
•
Do not place objects filled with liquids, such as vases on or near the product.
Do not use or store this product in a place where it is subject to direct sunlight, heat,
excessive dust or vibration.
•
Do not use this product with wet hands.
•
•
•
•
Do not clean this product with water or other liquids.
Do not block or cover the slots and holes in the product.
Do not push foreign objects into the slots or holes in the product.
Do not attempt to open this product yourself. There are no user serviceable parts
inside.
•
Do not allow children access to plastic bags.
SAFETY WARNINGS
•
•
Before using this product, read and follow all warnings and instructions.
This product is not intended for use by young children. Young children should be
properly supervised.
•
This product is intended for household use only and not for commercial or industrial
use.
•
•
Do not expose to dripping or splashing.
No naked flame sources, such as lighted candles, should be placed on the product.
•
Ventilation should not be impeded by covering ventilation openings with items such
as newspapers, table cloths, curtains and the like.
•
Make sure the unit is adjusted to a stable position. Damage caused by using this
product in an unstable position or by failure to follow any other warning or precaution
contained within this user manual will not be covered by warranty.
Lenco, suggests retaining the packaging in case for future transport of the product.
Prolonged exposure to loud sounds from personal music players may lead to
temporary or permanent hearing loss.
When participating in the traffic listening to a personal music player can make
the listener less aware of potential dangers such as approaching cars.
If at any time in the future you should need to dispose of this product please note that: All
batteries and accumulators need to be removed from this product (Removal of Waste
Batteries and Accumulators).
1.
Get to know the controls on Player
1
3
8
4
9
2
11
5
12
6
10
7
Item
Description
Item
Description
1
TFT Display
7
Mic Hole / Reset Switch Hole
2
Clip
8
(Previous / Fast-Backward)
(Next / Fast-Forward)
3
(Volume Up)
9
4
(Volume Down)
10
USB Mini Connector
5
Memory Card Slot
11
(Play / Pause / Standby ON OFF)
6
Earphone Output Jack
12
M (Menu / Enter / Select)
2.
About Player Battery
Player has an internal, non-user-replaceable battery. For best results, the first time you
use player, let it charge for about 2 hours or until the battery status icon in the “Connect”
screen shows that the battery is in full.
Battery is in full
Note: Player continues to use battery power after it’s been turned off, if unit isn’t used for a
while, the battery might need to be charged. Recharging the player at least 2 – 3 times in
three months for maintain the battery life and performance.
a.
b.
Charging the Battery:
You can charge the player battery in two ways:
Connect player to your computer. Or,
Use the USB power charger. (not included)
Connection and Charging:
Once you have connected player with computer / power charger, then you will see the
“Connect” screen appear on screen,
The level bars are running in battery status icon at the “Connect” screen. The battery is
in charging.
“Connect” Screen
In Charging
Important: The battery does not charge when your computer is in sleep. The USB port on
most keyboards does not provide enough power to charge the player. Connect player to a
USB 2.0 port on your computer only to prevent charge problem.
3.
Connecting and Disconnecting Player
You can connect the player with your computer to transfer those media files and
recorded voice memos when necessary, and to charge the battery.
a.
To Connecting Player
To connect player to your computer, plug the connector of USB Cable into a USB port
on your computer, and connect the other end to player, then the “Connect” screen
appear for view.
Now the player is ready for media files transfer with your computer and the battery is
charging.
You can transfer the media files by using the computer mouse use drag and place, or
copy and paste, in between the player and your computer. Disconnect it when you’re
done.
b.
To Disconnecting Player
It’s important not to disconnect player while it’s syncing or transferring files. Eject the
player before disconnect it.
To eject player, press and hold M button for about 2 seconds, the “Connect” screen will
switch to “Main Menu” screen. And now is safe to disconnect the player with your
computer. Unplug the USB cable from the player. Or,
If you’re using a Windows PC, you can also eject player in My Computer or by clicking
the “Safely Remove Hardware” icon in the Windows system tray, select the
correspondence name of USB Device and choose “Stop” > choose “Confirm” > choose
“Confirm” follow by the pop up windows you’re your computer.
If you’re using a Mac, you can also eject player by dragging the player icon on the
desktop to the Trash.
Disconnect the USB cable from the player and computer, simply remove it.
If you accidentally disconnect player without ejecting it, reconnect it to your computer
and sync again. However, some media file may loss.
4.
Getting Start the Player
Turn ON / OFF the player and use of Main Menu.
Press and hold
button for 3 – 4 seconds to turn ON the player, then you will see
any one of the following shown Main Menu screen, Music / Movie / Record /
Pedometer / Voice / Photo / Setup / Game / eBook, will appear on LCD after the
Loading and Opening screen have displayed.
To turn OFF the player, press and hold the
button for 3 – 4 seconds.
“Main Menu” screens
(If Music chooses)
(If Movie chooses)
(If Record chooses) (If Pedometer chooses)
(If Voice chooses)
(If Photo chooses)
(If Setup chooses) (If Game chooses)
(If eBook chooses)
5.
Use Setup Menu
You might need to set date & time or change some default setting as you desired in
setup sub menu before you start to use the player.
To go into setup menu, from main menu, choose “Setup” by use
/
button and
then press M button, a “Setup” menu appears to use.
You can go back to previous menu by press the
button during in setup menu. Or,
press and hold the M button to return to main menu.
Setup Menu
(Menu Page 1)
(Menu Page 2)
a.
To Setup “System time” (Date & Time):
Choose “System time” by using
/
time setting screen appears to use.
Press “+” button, the year is highlighted then adjusting to current year by pressing the
/
button. And repeating the adjusting methods by “+” and
/
button
button and then press M button, a date &
again for finished those items; Month, Date, Hour, Minute and seconds setting
adjustment.
Finally, you need to press the M button to confirm the adjustment and back to Setup
menu, if not the date & time will not to memorize and you need to adjust them again.
b.
To change “LCD set”
You can set the backlight to illuminate the screen for a certain amount of time as you
desired or make the backlight to always ON when every time you turn ON the player.
To change LCD backlight, choose “LCD set” > choose “Dark mode”, a level bar with
number appear then chose “0 (always On) / 5 / 10 / 15 / 20 / 25 / 30 / 35 / 40 / 45 / 50
(seconds)” as you desired by using M and
/
buttons. Choose “0” to prevent
the LCD backlight from turning to off. (choosing this option decrease battery
performance)
c.
To Change “Language”
This player can use difference OSD languages.
To set the language, choose “Language”, and then choose which language as you
desired by using M and
/
buttons.
d. To Set “Power Off”
The Power Off setting can extend the time between battery charges by turning OFF the
player when you are not using the controls or no operation. Also, Sleep function provided
for more choice.
To set power off time, choose “Power off”, then choose “Off time”, a levels bar with
number menu appear, then choose “0 - 200 seconds” as you want by using M and
/
buttons.
To set sleep time, choose “Power off”, then choose “Sleep time”, a levels bar with
number menu appear, choose “0 / 10 / 20 /30 / 40 / 50 / 60 / 70 / 80 / 90 / 100 / 110 /
120 minutes” as you want by using M and
/
buttons.
e. To Change “Online mode” (Applicable depend on Model)
You might need to change the online mode when connecting with computer system. In
the sense that some operating systems (under Windows 2K SP4) cannot support two driver
letters in one USB disk. The multiply driver is selected by device default; however, you can
change it when necessary.
To change type of disk, choose “Online mode” choose “Multiply driver / Normal only
(single ordinary disk) / Card only” by using M and
/
buttons.
f.
To View “Memory info”
You can view about the memory status of player, such as the numbers of remaining
memory space available and the percentage of memory have used.
To view the status, choose “Memory info” by using M and
/
buttons. An
information screen, remaining memory space available and percentage of memory
used, appear for view.
To return to setup menu or main menu press
button or press and hold M button
g.
To “Format Device”
You might need to format device the device memory. In some circumstances, the
device memory may be corrupted, or you may need to format the memory card if it newly
use with this device. However, you can format the device or memory card by the following
method but all data will be losses.
Choose “Format Device” then choose “Format Disk / Format Card” by using M and
/
buttons, and then choose OK to process or choose Cancel to exit and back
to setup menu.
h.
To View “Firmware Version”
You might need to view the details about firmware information inside the Player.
Choose “Firmware version” by using M and
screen appear for view.
i.
To return to setup menu or main menu, press
button or press and hold M button.
To “Firmware Upgrade” (System Utility Tools required)
You might need to upgrade the firmware for advanced the player performance or
/
buttons, an information
firmware getting trouble or damaged in some circumstance, such as electrostatic voltage
discharge issue happens. Please follow the instruction posted by the dealer (if any) or
follow the instruction from System Utility Tools if provided. It is not recommended to do if
the player is proper working.
j. To “Exit”
Select Exit to back to main menu. Or, press and hold the M button to go back main
menu.
6.
Use Music Menu
You can use music player to playback with supported music file format of audio coding;
WMA and MP3 are supported by the player. To open the music player in Main Menu:
From main menu, choose “Music” by using
Playing” screen appears to use.
/
and M button, a “Music Now
“Music Now Playing” Screen
a.
To Play Music
In Music Now Playing screen, press
Press
b.
Play Previous or Next Music
button to start the play.
button to pause the playing music. Press it again to play.
Press
Press
c.
Use Fast-Forward or Fast-Backward
Press and hold
button to use fast-forward
Press and hold
d.
Adjust volume level
In music playing, press or pressing
button to increase the volume levels, a change
volume control screen appears to view.
In music playing, press or pressing
button to decrease the volume levels, a change
volume control screen appears to view.
Wait for 6 – 8 seconds or press
button to return to music now playing screen.
button to play next music.
button to play previous music.
button to use fast-backward.
For hearing protection; a beep warning will be heard from earphone, or display warning
pop-up on TFT screen, when every time you increase the volume level and reach to the
default setting level which may exceed 85dB. Press M button to accept the warning and
enter into the volume control for increase the level and until to maximum level.
e.
Use Lyric Display
This player supports “*.LRC” lyric files and lyrics can synchronous displayed while
playing music if you music has lyric included. How to know whether the lyrics exist? If the
current song has matching lyric files, the color dot beside the Lyric Message icon will be
from red
in Music Now Playing screen.
turned to green color
Playing the music with lyrics, and then press and hold M button to enter the lyric display
mode and the lyrics is displaying and moving up accordingly with the playing music.
Press M button to cancel the lyrics display and go back to Music Now Play screen if
you want.
7.
Use Music Submenu in Music Stop Mode
You might need to selecting folders for music play and delete music files. To do this:
a.
Local Folder
In Music Now Playing screen, press
playing, then press M button to call up the Music Submenu.
In Music Submenu screen, choose “Local folder” a list menu appear, and then select
b.
button to stop the playing music if player is in
folder and / or choose a music file by using
/
and M button.
It will go back to music now playing screen once a music file is selected. Then press
button to play.
Delete file
In Music Submenu screen, choose “Delete file” a list menu appear, and then choose
which music file that you want to delete by using
/
and M buttons.
Once file is selected, press M button and choose Yes to confirm or No to cancel.
c.
Delete All
In Music Submenu screen, choose “Delete all” then selects “Yes / No” by using
button.
One “YES” or “NO” appear then press M button to confirm.
All music files will be deleted once YES is selected and confirmed, a “Deleting” screen
appear for a while and deleting process is in progress, then “Empty disk!” message will
shown on screen for few seconds.
d.
Exit
Select Exit to back to music now playing screen.
8.
Use Music Submenu in Music Playing Mode
You might need to do some changes for music playing, such as repeat, EQ settings for
/
music files… etc. To change setting:
a.
To Set Repeat
In music playing mode, press M button, a Music Submenu appear, then choose
“Repeat”, then choose “Normal / Repeat one / Folder / Repeat folder / Repeat all /
Random / Intro” as you desired by using
/
and M buttons.
b.
To Change Equalizer
In music playing mode, press M button, a Music Submenu appear, the choose
“Equalizer”, then choose “Natural / Rock / Pop / Classic / Soft / Jazz / DBB” as you
desired.
c. To set Replay Mode
Set Repeat A-B:
In Music Submenu, press M button, a list menu appear, then choose “Replay mode”
then choose “Replay”, a letter “A” is flashing in Music Now Playing screen, then press
button to select the starting point of track “A”.
Then a letter “B” is flashing once “A” is selected, use
button again to select the
ending point of track “B” which you want by using
distance of track is repeating.
button. And now the A – B
However, the repeating time and the replay gap time is depend on the set values of
Replay Time and Replay Gap have mentioned in below items.
To create another A – B distance of track to repeat, press
button again and then
again. a new created A – B distance of track is repeating.
To cancel the repeat A – B function, press the M button. Or press
button to pause.
Set Replay Times:
In music playing mode, press M button, a Music Sub-menu appear, the choose
“Replay times”, then choose “1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9 / 10” as you desired by using
/
and M buttons. The Player will replay those music file as your selected
number of times accordingly.
Replay Gap:
In music playing mode, press M button, a Music Sub-menu appear, the choose
“Replay Gap”, then choose “1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9 / 10 second(s)” as you desired
by using
/
and M buttons. The replay gap time in between music to music or
in repeat A- B will replay and stop according the selected number of time.
d.
Exit
Select Exit to back to music now playing screen.
9.
a.
Use Movie Menu
To Play Movie
From Main Menu, choose “Movie” by using
/
and M button, a “Movie Now
Playing” screen appears to use.
In Movie Now Playing” screen, press
key to start the play.
Press
button to pause and to back to Movie Now Playing screen. Press it again,
the video will play continue.
b.
To Play Previous or Next Video
Press
button to play next movie file.
Press
button to play previous movie file.
c.
Use Fast-Forward or Fast-Backward
Press and hold
button to play fast-forward.
Press and hold
button to play fast-backward.
d.
Adjust Volume Level
In movie playing, press or pressing
button to increase the volume levels.
In movie playing, press or pressing
button to decrease the volume levels.
To preset the volume level at movie stop mode, in Movie Now Playing screen press
/
key to preset your desired volume levels, a volume control screen appears to
view. Press
/ M button to return to Movie Now Playing.
For hearing protection; a beep warning will be heard from earphone, or display warning
pop-up on TFT screen, when every time you increase the volume level and reach to the
default setting level which may exceed 85dB. Press M button to accept the warning and
enter into the volume control for increase the level and until to maximum level.
10. Use Movie Submenu
You might need to selecting folders, delete movie files and set repeat for movie play.
you can make change during in the playing mode at Movie Now playing screen To do this:
In “Movie Now Playing” screen, press M button to enter to movie submenu.
a.
Local Folder
In movie submenu screen, choose “Local Folder”, a file list menu appear, and then select
folder and / or choose a desired movie file to play by using
/
and M button.
It will go back to music now playing screen once a music file is selected. Then press
button to play.
b.
Delete File
In movie submenu screen, choose “Delete file” a file list menu appear, and then choose which
movie file that you want to delete by using
/
buttons.
Once file is selected, press M button and choose “Yes” to confirm or “No” to cancel.
c.
Delete All
In movie submenu screen, choose “Delete all” then selects “Yes / No” by using
button.
One “YES” or “NO” appear then press M button to confirm.
All movie files will be deleted once YES is selected and confirmed, a “Deleting” screen
appear for a while and deleting process is in progress, then “Empty disk!” message will
shown on screen for few seconds.
d.
Repeat
In movie submenu, choose “Repeat”, then choose “Normal / Repeat one / Folder / Repeat
folder / Repeat all / Random / Intro” as you desired by using
e.
/
and M buttons.
Exit
Select Exit to back to music now playing screen.
11. Convert Video files into AMV
This tool can be used to transform those video files into AMV files on the computer
before you upload them to you player.
To install this video convert tool to you computer, click “Utilities > video conversion
software” in provided CD. (or stored in your Player)
Select “Setup” to start the install program, the software will automatically install to you
computer.
After installation is done, open AMV Video converter on the PC
Noted: This program is used to convert video files into AMV format, currently only AMV
format is supported.
/
Run “AMV Video Converter”, click
to choose the folder where to save the AMV
files, and then click
to select the folder where the original files are. The original file
will show in the file window once selected.
Select with highlight the unprocessed AMV files in the file window, the
highlighted into
. And then click
icon will be
icon and a dialog box will be shown.
Choosing pixels of AMV to “160x120” and Frames per second to “middle”, then click
OK to confirm.
Click
After conversion, the AMV files will play automatically for preview.
And now the converted AMV file is ready to transfer, you can simply copy and place
those converted AMV files to the media player.
to start converting.
Note: Only pixels in 160x120 can be supported.
12. Use Record Menu
You can use the player as a Voice Recorder and recording voice memos using the
built-in microphone.
a.
To Start Recording Voice Memo
From main menu, choose “Record” by using
Recording” screen appear to use.
/
and M buttons, a “Now
“Now Recording” Screen
b.
To Start / Pause Recording
Press
button to start the recording and the recording time is running.
Press
button to pause the recording and recording time will stop and flashing.
Press it again the recording and time will run continue.
c.
To Save and Stop Recording File
Press and hold M button, the recorded file will saving into memory.
13. Use Record Submenu (in Stop Mode)
You might need to change the folder locations which want to store the record file and /
or change record quality to better compression values.
In Now Recording screen at stop mode, press M button, a “Record Sub-menu appear
to use.
a.
Local folder
In record submenu, choose “Local folder” and then choose the folder name which you
want to save the record file by using
/
and M buttons.
Once folder name selected, press and hold the M button, then the folder location is
changed and go back to Now Recording screen.
And now you can see the folder name is changed at the Record Folder icon in “Now
Recording” screen.
b.
Record Type
In record submenu, choose “Record type”, then choose “32K BPS / 64K BPS / 128K
BPS / 256K BPS” values as you desired by using
/
and M buttons.
c.
Exit
Select Exit to back to now recording screen.
14. Use Pedometer
From main menu choose “Pedometer” by using
pedometer menu appears to use.
/
and M buttons. A
Pedometer Menu
a.
Setup your pedometer before start
Before you start to use the pedometer function, you need to input your personal
information and calibrates the player’s pedometer sensor to personalize it.
From pedometer menu, choose “Pedometer”, then choose “Setting” by using
/
and M buttons. A sub list menu appears to use.
Choose “Women / Man”, then choose stride “Walking / Jogging / Running”, a level
bar with number appear to choose. Input your average stride length, for example 80
(cm) refer to “Stride Length Measurement” as illustrated below, by using
/
and M buttons. Once average stride length is set, it will return to pedometer menu.
(Adjustment range can be set from 10 – 200 (cm) by increase / decrease 1 cm step)
b.
Choose “Setting” to change the setting again if you want.
Choose “Exit” to return to main menu.
Stride length measurement
Walk / Jog / Run 10 steps with your normal stride as illustrated below.
Measure the distance from START to END in centimeter (cm). Then calculate your
stride length by dividing the total distance by 10. Example:
Total distance = 800 cm
800 cm ÷ 10 steps = 80 cm
c.
Start / Exit pedometer counts & Look Up record
Choose “Start” to enter and start pedometer counts function when settings are
completed, the pedometer counts display is appearing and time is start running, from
“00:00:00”. At same time pedometer sensor is starting to counts your move. Now you
can start the walk.
Those wanted information; such as: Steps, Distance, Calorie burned and Speed, are
showing on pedometer counts display screen for view.
Pedometer Counts Display
To Exit pedometer counts function and Save the personal counts record, press M
button, a confirm screen appear, then choose “Yes” to confirm and the screen will
return to main menu. The record saved. Or, choose “No” to cancel and continue the
pedometer counts.
In pedometer menu, choose “Look up” to view the personal counts record. The player
is allowed storing maximum 2 personal counts record “Record 1 / Record 2”.
Moreover, the new records will overwrite the old Record 1 and Record 2. Press M
button to exit from personal counts record display and back to main menu.
Personal Counts Record
d.
Play Music in Pedometer Function
From pedometer menu, choose “Local folder / Card folder” > by using
/
and M buttons. A list menu with folders / files appears to choose.
Choose a folder and file, which music as the first music to play, when you start to play
song in pedometer counts display mode. The screen will return to pedometer menu.
Then,
Choose “Start” to enter the pedometer counts display mode. Press
button to start
the music play music with the pedometer counts function if you wish, and you can
button again. Or, just only using the pedometer counts
pause / stop by press
function.
e. Music controls in pedometer (same as music mode)
In pedometer counts mode
Press
button to start the play. Press it again to pause.
Press
button to play next music.
Press
button to play previous music.
Press and hold
button to use fast-forward
Press and hold
button to use fast-backward.
In music playing, press or pressing
button to increase the volume levels, a change
volume control screen appears to view.
In music playing, press or pressing
button to decrease the volume levels, a change
volume control screen appears to view.
Press
button to return to music now playing screen.
Note: In pedometer mode, some music settings are defaulted and cannot be changed.
Such as Repeat All (Cycling), In Order Play.
f.
Attaching the player for pedometer
Place the unit on Armband
Put the unit on your waistband and adjust it to
comfortable position.
Place the unit in your pocket
Do not place the unit in the back pocket of your pants, to
prevent sitting on it.
Close the zipper / button of your pocket (if available) to
prevent the unit from dropping.
Place the unit in your bag
Place the unit in a secure section or partition of your bag.
Make sure the unit is placed horizontal or vertical in a
pocket in the bag.
Hanging the unit from your neck
Attach a secure lanyard or string to the unit. (not
provided)
Place the lanyard around your neck and hang the unit as
illustrated.
NOTE: Make sure the lanyard / string is correctly sized to
easily remove the unit from around your neck. If used
hanging around neck, the lanyard / string can cause
strangulation. Do not place the unit with lanyard / string
around a child’s neck.
g.
The unit may not count steps correctly in the following conditions:
The unit is not positioned correctly.
When the front of the main unit is placed in the angle of
less than 60° or horizontal to the ground.
NOTE: The unit can count steps even if it is slanted or placed
upside-down, or if the main unit is perpendicular to the
ground.
The unit moves loosely.
When the unit is loose or flat in your pocket or bag (not in
a horizontal or vertical position).
When the unit swings from your belt, the top of your
pants or a bag.
Up and down movement.
Standing up and/or sitting down movement.
Playing sports other than walking.
Ascending or descending movement at stairs or in a
steep slope.
Walking at an inconsistent stride.
When you shuffle or wear sandals.
Starting and stopping or other forms of inconsistent
walking.
Walking extremely slowly.
Vibrations from a moving vehicle.
Such as riding a bicycle, automobile, train or bus.
15. Use Voice Menu
For playback and manage the recorded voice memos file.
From main menu, choose “Voice” menu by using
Now Playing” screen appear to use.
/
and M buttons, a “Voice
“Voice Now Playing” Screen
a.
To Play and Pause Recorded Voice Memos
In Voice Now Playing screen, press
button to start to play the recorded file.
Press
button to pause the playing file.
b.
To Play Previous or Next File
Press
button to play next file.
Press
c.
To Fast-Forward or Fast-Backward
Press and hold
buttons to use fast-forward
Press and hold
button to use fast-backward.
d.
Adjust volume level
In music playing, press or pressing
button to increase the volume levels, a change
volume control screen appears to view.
In music playing, press or pressing
button to decrease the volume levels, a change
volume control screen appears to view.
Wait for 6 – 8 seconds or press
button to return to music now playing screen.
button to play previous file.
16. Use Voice Submenu in Stop Mode
You might need to change some setting as you desired for playing Voice file, you can
make change during in the playing mode at Voice Now Playing screen
a.
Local Folder
In Voice Now Playing screen, press
button to pause / stop the playing file, if in
playing mode, then press M button to call up the voice submenu.
In Voice submenu screen, choose “Local folder” a list menu appear, and then select
folder and / or choose a voice file by using
/
and M button.
It will go back to music now playing screen once a music file is selected. Then press
button to play.
b.
Delete File
In voice submenu screen, choose “Delete file” a list menu appear, and then choose
which voice file that you want to delete by using
/
and M buttons.
Once file is selected, press M button and choose Yes to confirm or No to cancel.
c.
Delete All
In voice sub-menu screen, choose “Delete all” then selects “Yes / No” by using
button.
One “YES” or “NO” appear then press M button to confirm.
All music files will be deleted once YES is selected and confirmed, a “Deleting” screen
appear for a while and deleting process is in progress, then “Empty disk!” message will
/
shown on screen for few seconds.
d.
Exit
Select Exit to back to music now playing screen.
17. Use Voice Sub-menu in Playing Mode
You might need to do some changes for music playing, such as repeat, EQ settings for
music files… etc. To change setting:
a.
Repeat
In voice playing mode, press M button, a Music Sub-menu appear, then choose
“Repeat”, then choose “Normal / Repeat one / Folder / Repeat folder / Repeat all /
Random / Intro” as you desired by using
/
and M buttons.
b. Replay Mode
Set Repeat A-B:
In voice playing mode, press M button, a list menu appear, then choose “Replay
mode” then choose “Replay”, a letter “A” is flashing in Voice Now Playing screen, then
button to select the starting point of track “A”.
press
Then a letter “B” is flashing once “A” is selected, use
button again to select the
ending point of track “B” which you want by using
button. And now the A – B
distance of track is repeating.
However, the repeating time and the replay gap time is depend on the set values of
Replay Time and Replay Gap have mentioned in below items.
To create another A – B distance of track to repeat, press
again. a new created A – B distance of track is repeating.
button again and then
To cancel the repeat A – B function, press the M button. Or press
Set Replay Times:
button to pause.
In voice playing mode, press M button, a Music Sub-menu appear, the choose “Replay
times”, then choose “1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9 / 10” as you desired by using
/
and M buttons. The Player will replay those music file as your selected number of times
accordingly.
Replay Gap:
In voice playing mode, press M button, a Music Sub-menu appear, the choose “Replay
Gap”, then choose “1 / 2 / 3 / 4 / 5 / 6 / 7/ 8 /9 / 10 second(s)” as you desired by using
/
and M buttons. The replay gap time in between music to music or in repeat
A- B will replay and stop according the selected number of time.
c.
Exit
Select Exit to back to music now playing screen.
Note: Press and hold the M button will go back to Main Menu directly.
18. Use Photo Browse
You can use the player as picture / photo viewer:
To browse picture / photo file, from main menu choose “Photo” by using
M button, a list menu appear to use.
Choose a file by using
/
button, and then press
Press
button to stop and to go back to list menu for other files selection.
To change previous / next photo, press
/
button.
Press and hold M button to back to main menu.
/
and
button to play.
19. Use Photo Submenu in List Screen
You might need to change some setting for photo browse. To change setting:
a.
Local Folder
In list menu, press M button to call up the photo submenu.
In photo submenu, choose “Local folder” a list menu appear, and then choose folder
and file to browse by using
/
Once photo file is selected, press
and M button.
button to play.
b.
Playback Set
In photo submenu, choose “Playback set” and then choose “Manual play”. However,
/
button to browse next / previous photo in photo playing
you need to use
mode when Manual Play is selected.
Choose “Auto play”, a setting menu appear, then choose “2 / 3 / 4 / 5 / 5 / 6 / 7 / 8 / 9 /
10 seconds)” as you desired by using
/
and M buttons. The slide show
function is activated as your selected time gap to playing the photo files one by one
automatically.
c.
Delete file
In photo submenu, choose “Delete file” a list menu appear, and then choose which
photo file that you want to delete by using
/
button.
d.
Once file is selected, press M button and choose Yes to confirm or No to cancel.
Delete All
In photo submenu, choose “Delete all” then selects “Yes / No” by using
button.
One “YES” or “NO” appear then press M button to confirm.
All photo files will be deleted once YES is selected and confirmed, a “Deleting” screen
/
appear for a while and deleting process is in progress, then “Empty disk!” message will
shown on screen for few seconds.
e.
Exit
Select Exit for back to photo browse list menu screen.
20. Use Game Menu
There have a game name “Snake”. Control the snake move up, down, left and right to
eat the food (dot) which will exist somewhere on TFT screen. The snake’s body will get
longer at every eats for food, but don’t let the snake hit the walls and hit the snake body.
To play game, from Main menu, choose “Game” menu, then choose a game to play.
Control KEY instruction; Press:
Pause.
: up,
Press and hold M button to exit the game.
: down,
: left,
: right,
:
21. Use eBook Menu
You can use the player as a text reader with supported file format (.TXT).
a.
To open eBook
From main menu, choose “eBook” by using
appears to use.
Choose a file which you want to read by using
button to play.
Press
button to change next page,
Press
button to go back to previous page,
Back to list menu screen, press
button.
Go back to main menu, press and hold M button
/
and M buttons. A list menu
/
button, and then press
22. Us eBook Submenu in list menu screen
You might need to change some setting for eBook reading. To change setting:
a.
Local Folder
In eBook list menu screen, press M button to call up the eBook Submenu.
In eBook Submenu, choose “Local folder” a list menu appear, and then choose folder
and file by using
/
button.
Once file is selected, press M button then
b.
Playback Set
In eBook Submenu, choose “Playback set” and then choose “Manual play”. You need
to use
/
button to change next / previous page for reading when Manual Play
is selected. Or,
Choose “Auto play”, a setting menu appears, then choose “1 / 2 / 3 / 4 / 5 / 5 / 6 / 7 / 8
/ 9 / 10 second(s)” as you desired by using
/
and M buttons. The Page Flip
function is activated as your selected time gap to playing.
button to read.
c.
Delete file
In eBook Submenu, choose “Delete file” a list menu appear, and then choose which
eBook file that you want to delete by using
/
button.
d.
Once file is selected, press M button and choose Yes to confirm or No to cancel.
Delete All
In eBook Submenu, choose “Delete all” then selects “Yes / No” by using
/
button.
One “YES” or “NO” appear then press M button to confirm.
All eBook files will be deleted once YES is selected and confirmed, a “Deleing” screen
appear for a while and deleting process is in progress, then “Empty disk!” message will
shown on screen for few seconds.
e.
Exit
Select Exit for back to eBook list menu screen.
23. Us eBook Submenu in Playing Mode
You might need to add, select and delete some bookmark when you reading, to do this:
a.
Bookmark Select
b.
In eBook playing mode, choose “Bookmark select” by using
/
and M button.
Choose a stored bookmark which you want to call and then press M button to play.
Bookmark Delete
In eBook playing mode, choose “Bookmark delete” a list menu appears, and then
/
button.
choose which saved bookmark you want to delete by using
Once bookmark is selected, press M button to confirm. The bookmark is deleted and
go back to current reading play.
c.
Bookmark Add
In eBook playing mode, select the reading page you want to bookmark, press M button
to call up eBook submenu.
Choose “Bookmark Add” by using
/
button and then press M button, the
pages is saved into bookmark and go back to current reading page automatically.
d.
Exit
Select Exit for back to eBook list menu screen.
24. Use Memory Card Slot
This player allows you to play those support media files from your memory card
(T-Flash). Also it will increase the mobile hard disk memory capacity of the player if you use
this option.
a.
To Play From Memory Card:
Turn Off the player. Now insert your Micro SD memory card into the memory card slot
on side of player.
Turn On the player and now the Micro SD memory card, T-Flash, is ready to use.
The “Card folder” item will be existed to use when you enter into those music, movie,
photo, , Record, Voice and eBook submenu.
Go into the card folder and choose you desired folder(s) and file(s) to play.
To take out the Micro SD memory card, turn Off the player.
25. To Reset Player
In some circumstances the device may hanging and need to reset. This player has
design with built-in a mini tact switch which located at the bottom in the Mic hole, so it can
provide the reset function to restart the device pass through the Mic hole.
To do reset, Use a 0.8 mm stick or similar object (like tooth stick), and carefully insert
the stick, use dull side, into the Mic hole until you feel to hit the end. Actually that is the
tact switch button surface.
Then add a bit of force and you will get a click sound and feeling return from switch.
The device is reset; all settings are back to factory default. The device status LED will
light up and will go into play mode automatically.
Do not reset the device if it is proper working.
26. Trouble Shooting
Unit cannot turn ON
* Check battery is it charged with enough
energy.
No sound is heard from
headphone.
* Check whether Volume is set “0” and
connect the headphone plugs firmly.
* Check whether the headphone plug is
dirty.
* Corrupted MP3 may make a static noise
and the sound may cut off. Make sure that
the music files are not corrupted.
Characters in LCD are corrupted
* Check whether the right language has
been selected.
Download of music files fails.
* Check whether USB cable is damaged
and is connected properly.
* Check whether driver is installed correctly.
* Check whether the player’s memory is in
full.
27. Specification
Dimension
53.5 mm (H) x 43 mm (W) x 18 mm (D)
Weight
28g
LCD
1.8 Inches, Resolution (RGB)128 x 160
PC connection
USB 2.0 (high speed)
Earphone Impedance 32 Ohm
Internal Memory
See carton
Lithium 3.7V, 170mAh
Battery
Max. Play Time: > 8 - 10 Hours (MP3 music with power
saving mode)
Max. Output Power of L = 275mV(rms) at 32 Ohm
Earphone
R = 275mV(rms) at 32 Ohm
Frequency Responses
20Hz to 20,000Hz
SNR
> 60dB
Music Format
MP3 / WMA
32Kbps – 320kbps
Movie Format
AMV
Recorder Coding
WAV
Picture Format
JPEG / BMP / GIF
eBook Format
TXT
0 to 40℃
Audio
Operating
Temperature
Operating System
32 / 64 / 128 / 256kbps
Window 2000/XP/Vista/Win7, Mac 9.2 or above
28. Disclaimer
Updates to Firmware and/or hardware components are made regularly. Therefore
some of the instruction, specifications and pictures in this documentation may differ slightly
from your particular situation. All items described in this guide for illustration purposes only
and may not apply to particular situation. No legal right or entitlements may be obtained
from the description made in this manual
29. Service and support
For information: www.lenco.com
For support: http://lencosupport.zendesk.com
Lenco helpdesk:
Germany
0900-1520530
(Local charges)
The Netherlands 0900-23553626 (Local charges + 1ct p/min)
Belgium
02-6200115
(Local charges)
France
03-81484280
(Local charges)
The helpdesk is accessible from Monday till Friday from 9 AM till 6 PM.
When contacting Lenco, you will always be asked for the model and serial number of your
product. The serial number can be found on the back of the device. Please write down the
serial number below:
Model: PODO-152
Serial number:_________________________________
Lenco offers service and warranty in accordance to European law, which means that in
case of repairs (both during and after the warranty period) you should contact your local
dealer.
Important note: It is not possible to send products that need repairs to Lenco directly.
Important note: If this unit is opened or accessed by a non-official service center in any
way, the warranty expires.
This device is not suitable for professional use. In case of professional use, all warranty
obligations of the manufacturer will be voided.
This symbol indicates that the relevant electrical product or battery should
not be disposed of as general household waste in Europe. To ensure the
correct waste treatment of the product and battery, please dispose them in
accordance to any applicable local laws of requirement for disposal of
electrical equipment or batteries. In so doing, you will help to conserve
natural resources and improve standards of environmental protection in
treatment and disposal of electrical waste (Waste Electrical and Electronic
Equipment Directive).
Products with the CE marking comply with the EMC Directive (2004/108/EC)
and the Low Voltage Directive (2006/95/EC) issued by the Commission of
the European Community.
The declaration of conformity may be consulted at
http://www.lenco.eu/supportfiles/CE/jhvf7y80jasdol.pdf
®All rights reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement