Contents: AWS 70
AWS 70
Band 4, 70 dB
Adjustable Gain 1700/2100 MHz
In-Building Wireless Smart Technology
Signal Booster
™
Contents:
Antenna Options & Accessories . . . . . . . . . . . . . . . . . . . . . . . . 1
Quick Install Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Outside Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the Inside Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing a Wilson Electronics Signal Booster. . . . . . . . . . . . . . 8
Powering up a Wilson Electronics Signal Booster . . . . . . . . . . . 8
Finding the Strongest Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Understanding the Signal Booster Lights . . . . . . . . . . . . . . . . 10
Warnings and Recommendations . . . . . . . . . . . . . . . . . . . . . . 12
Guarantee & Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Appearance of device and accessories may vary.
Note: This manual contains important safety and operating information. Please read and
follow the instructions in this manual. Failure to do so could be hazardous and result in
damage to your Signal Booster.
Installation Instructions for the Following
Wilson Electronics Signal Booster:
AWS 70 Band 4, 70 dB Adjustable Gain 1700/2100 MHz
In-Building Wireless Smart Technology ™ Signal Booster
Model # 272365 FCC ID: PWO272365 IC: 4726A-272365
Model # 272365G Only for use with International Carriers outside the U.S.A. and Canada
The term “IC” before the radio certification number only signifies that Industry Canada technical
specifications were met.
How it Works
Wilson Electronics Signal Boosters are bi-directional devices that deliver service
levels consistent with what would be expected in areas of high cell network coverage.
They amplify a weak or shadowed signal in mobile, marine, machine to machine
and in-building applications. When using a Wilson Electronics Signal Booster in
conjunction with Wilson Electronics antennas, the Outside Antenna will collect the
cell tower signal and send it through the cable to the Signal Booster. The signal is
then amplified and re-transmitted through the Inside Antenna into the room. Cell
phones and cellular data cards in that area then communicate with the improved
signal. When a cell phone or cellular device transmits, the signal is received by
the Inside Antenna, amplified by the Signal Booster and transmitted back to the
cell tower through the Outside Antenna.
Inside this Package
Note: Kits may contain different accessories
6V / 2.5A
AC/DC
Power Supply
Signal
Booster
(#859912)
Outdoor Antenna Option
1. Wide Band Directional Antenna
700 MHz - 2700 MHz (#304411)
See RF Safety Warning (page 12)
for proper installation.
1
Indoor Antenna Options & Accessories
A. Wide Band Panel Antenna 700-2700MHz
(multiple mounting options)
B. 50 Ohm Lightning Surge Protector with N-Connector
(#859902)
Splitter options on page 8
A
B
Appearance of device and accessories may vary.
1
To purchase, call Wilson Electronics Sales Department at: 800-204-4104
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Quick Install Overview
See Installation Diagram on page 3 & 4. Contact Wilson Electronics Technical
Support Team with any questions at 866-294-1660.
1. Select a location to install the Signal Booster that is away from excessive heat,
direct sunlight, moisture and has proper ventilation. Do not place the Signal
Booster in an air-tight enclosure.
2. Select a location on the roof of the building to install the Outside Antenna. Use
a cell phone in test mode to find the strongest signal from the cell tower. Visit
www.WilsonElectronics.com to find test mode function for your particular cell
phone (see page 9).
3. Run the Outside Antenna cable to the Signal Booster and attach it to the
connector labeled “Outside Antenna”. Run the Inside Antenna cable to the
Signal Booster and attach it to the connector labeled “Inside Antenna” (see
page 7 for more information on running cable). Lightning Surge Protection is
recommended for all in-building installations (see page 6).
4. Select a location for the Inside Antenna, preferably in the center of where the
signal needs to be amplified. A minimum separation distance of 20 vertical
(within the null zone) or 50 horizontal feet is necessary for proper operation.
If the inside coverage is not sufficient you may need to increase the separation
distance even further (see installation diagram on pages 3 & 4).
5. Before powering up the Signal Booster, verify that both the Outside Antenna
and the Inside Antenna are connected and check that all connections are tight.
Note: Be careful when plugging the connectors in so as not to bend the center
pins on the connectors.
6. The Signal Booster has been packaged with the gain control knobs adjusted to
the highest gain position. If the light is not green, please refer to pages 10-12.
Warning: Connecting the Signal Booster directly to a cell phone with use of
an adapter will damage the cell phone and/or the Signal Booster.
IMPORTANT NOTICE
• It is very important to power your Signal Booster using a surge protected AC
Power Strip with at least a 1000 Joule rating.
• Failure to do this will void your warranty in the event of a power surge or
lightning strike.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
2
Installation Diagram
Note: Per FCC rules, height not to
exceed 10m (32’ 9”) above ground.
Ou
Outside
ut
Antenna
An
t
See RF Safety Warning (page 12) for proper
installation.
Inside Antenna
Preferred Method: Place the Inside
Antenna in the ceiling facing down for
the best coverage.
coax cable
Note: The Inside Antenna may be
mounted on the wall directly under the
Outside Antenna, in the null zone, if
20 feet of vertical separation can be
maintained.
Null Zone: The area under the
Outside Antenna, where the
Outside Antenna radiates the least.
Note: A Lightning Surge Protector is
recommended for all building installations
(sold separately). Make sure the protector
is installed in line between the Outside
Antenna and the Signal Booster.
Inside Antenna
(Optional
second
antenna for
additional
coverage).
Power
Supply
Typical Installation
3
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
866 29 1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Before Getting Started
This guide will help you properly install your Wilson Electronics Signal Booster. It
is important to read through all of the installation steps for your particular
application prior to installing any equipment. Read through the instructions,
visualize where all the equipment will need to be installed and do a soft
installation before mounting any equipment. Contact Wilson Electronics Technical
Support with any questions at: 866-294-1660.
Splitter (2-way, 3-way or
4-way if using multiple
inside antennas)
Lightning
Surge Protector
(recommended)
Inside Antenna
(Optional
third antenna
for additional
coverage).
Signal
Booster
Surge Protector
Power Strip
Contact
C
t t Wilson
Wil
Electronics
El t i Technical
T h i l Support
S
t Team
T
with
ith any questions
ti
att 866-294-1660
866 294
4 1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
4
Reasons for Weak Cellular Signals
Anyone who uses a cell phone or cellular data card knows the frustration of not
being able to connect to or maintain a strong cellular signal. When this occurs, it
is generally due to one of two reasons:
1. Location of the Nearest Cell Tower – Cell towers are situated to provide
broad coverage; however, there are many areas in which signal strength
may be reduced by topographic features or by local government restrictions
on the height or placement of the towers themselves. Rural areas generally
have fewer cell towers than urban regions.
2. Natural and Man-Made Obstructions – Signal strength can also be negatively
affected by trees, hills, buildings, weather, and other obstructions. You may
be relatively close to a cell tower but still unable to make a call. This often
occurs in homes, offices and other buildings in which stucco, concrete or
metal walls may block the signal.
The Signal Booster works with two antennas. The Inside Antenna communicates
with your cellular device and the Outside Antenna communicates with the cell
tower. The Outside Antenna receives the cell tower signal and sends it through
the cable to the Signal Booster, where it is amplified and re-transmitted much
stronger through the Inside Antenna into the room. When the Inside Antenna
picks up a signal from your cellular device, the Signal Booster amplifies that
signal and transmits it through the cable to the Outside Antenna and back to the
cell tower.
Note: The Signal Booster will only operate if there is an adequate signal to amplify.
Outside Antenna Installation
(Wide Band Directional Antenna shown)
Drip hole on bottom
Cell Tower
The Outside Antenna should be mounted as shown in the illustration above.
The mounting bracket, included with Outside Antenna, is adjustable and will
accommodate pipe diameters from 1.25 inches to 2 inches (pipe sold separately
#901117). Mount the antenna so that there is at least 3 feet of clearance in all
5
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
directions around it. Position the antenna so that it has an unobstructed line of
sight to the cell tower’s strongest signal. Make sure the Outside Antenna is not
pointing across your own roof or at the Inside Antenna as this will cause the
oscillation protection circuitry to shut down the Signal Booster.
Warning: Lightning protection is recommended for all installations (sold
separately). Take extreme care to ensure that neither you nor the
antenna comes near any electric power lines.
Installing Lightning Protection
(sold separately)
Install the Lightning Surge Protector
(LSP) close to the Signal Booster.
Attach the cable from the Outside
Antenna to the surge protector, using
a short length of low loss cable; attach
one end to the LSP and the other to
the Outside Antenna connector on the
Signal Booster. Ensure the LSP is
properly grounded (ground wire not
included). LSP may be purchased at
www.WilsonElectronics.com or call
800-204-4104 (#859902).
To Outside
Antenna
Lightning
Surge Protector
(sold separately)
Ground Wire
(not included)
To Signal Booster
To Inside
Antenna
Signal Booster
Surge Protector Power Strip
Selecting a Direction for the Outside Antenna
Select a location on the roof of the building to install the Outside Antenna. Use a
cell phone in test mode to find the strongest signal from the cell tower (see page
9). To get the strongest signal possible, it is very important to set up your Outside
Antenna properly. The Inside and the Outside Antenna must be mounted in such
a way that they are able to pick up the best possible cell signal on the outside
of the building and provide the best possible signal on the inside of the building.
Mount the Outside Antenna as high as possible (see note on page 3) facing the
cell tower in an area with the best possible signal coverage.
Note: Never point the front of a directional antenna toward the Inside Antenna.
See Figures 1 & 2 on page 10.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
6
Mounting Tips for Running Outside Antenna Cable
If you are mounting the Outside Antenna on the roof of your building, we have
found that it is easiest to run your cable underneath the down side of your roof’s
flashing. If you have satellite TV service installed at your home or office, you
may be able to follow the same route as the satellite TV cables that are already
running from outside of your building to the inside.
After routing the cable, we recommend sealing any areas where the cable
passes into the building with silicone, cable bushings or other waterproof sealant
to keep your installation from leaking. If you are mounting the Outside Antenna
to the outside wall of your home or building, the simplest way is to run the cable
on the outside of the wall and attach it to the exterior of your home or office. Then
drill a hole through the wall where you want the cable to appear on the inside of
the building. Before drilling, make sure that there are no electrical outlets, sewer
or water pipes, or electrical wiring in the wall that you are about to drill through as
this could potentially harm you or damage the building.
After drilling the required hole, run the cable through and seal it with silicone,
cable bushings or other waterproof sealant to enclose the hole that you have
created. In some instances, it may be possible to run the cable up into the fascia
of the attic overhang. In this circumstance, the cable will be accessible in the attic
for further routing.
Installing the Inside Antenna
(Included in some kits)
Select a location for the Inside Antenna, preferably in the center of where the
signal needs to be amplified. A minimum separation distance of 20 vertical feet
(within the null zone) or 50 horizontal feet is necessary for proper operation.
If the inside coverage is not sufficient you may need as much as 75 feet of
horizontal separation. Refer to installation diagram on pages 3 & 4.
Inside
Antenna
Ceiling
Rafters
Ceiling
Drywall
f instance
i t
In some cases, multiple Inside Antennas may be required, for
iff you
have multiple rooms with poor signal. A signal may be split by using a splitter
7
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
(sold separately). Refer to configuration
on pages 3 & 4.
Splitter Options:
(sold separately)
Warning: An Inside Antenna must
have a separation distance from all
persons that is at least 15 inches for the
panel antenna.
2-way
(859957)
3-way
(859980)
4-way
(859981)
Installing a Wilson Electronics Signal Booster
Select a location to install the Signal Booster that is away from excessive heat,
direct sunlight, moisture and that has proper ventilation. Do not place the Signal
Booster in an air-tight enclosure. Recommended installation locations for inbuilding Signal Boosters are near a power outlet and in a closet, or on a shelf.
Note: It is important to have adequate air ventilation. Maintain at least 6 inches of
clearance from surrounding objects.
Run the Outside Antenna cable to the Signal Booster and attach it to the
connector labeled “Outside Antenna”. Run the Inside Antenna cable to the Signal
Booster and attach it to the connector labeled “Inside Antenna”.
Note: For distances of 20 feet or more, use Wilson low loss cable to prevent
significant signal loss. Be careful when plugging the connector in so as not to
damage the center pins on the connectors.
Powering up a Wilson Electronics Signal Booster
1. Never point the front of a Directional Outside Antenna toward the Inside
Antenna. See Figures 1 & 2 on page 10.
2. Ensure that both the Outside Antenna cable and the Inside Antenna cable are
connected to the Signal Booster and the connections are tight.
3. Plug the power supply into the Signal Booster input marked “POWER” (carefully,
to avoid damaging the center pin) and then into a surge protected AC Power
Strip with at least a 1000 Joule rating.
4. If the Signal Booster does not have a green light please see pages
10-12.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
8
5. Using multiple Signal Boosters in one installation could cause interference
to the cell tower. Except for the use of the In-Line (806215).
6. Contact Wilson Electronics Technical Support Team with any questions at
866-294-1660 or email [email protected] Technical Support
hours are 7 am to 6 pm MST.
Finding the Strongest Signal
Cell Signal
Outside
Wide Band
Antenna
Cell Tower
When installing your Signal Booster’s Outside Antenna, aiming it towards the
best signal source from you service provider is important. After you have
completed the install, the best way of getting the strongest signal is to have
one person on the roof to rotate the Outside Antenna, which is connected to
the Signal Booster. Turning the Outside Antenna about 45 degrees at a time,
while the second person is watching the signal strength on the phone inside
the building. This allows you to read the signal strength from the cell tower. It is
preferable to have the phone in the test mode so the actual signal strength can
be read, as bars are not the most accurate. Go to www.WilsonElectronics.com
for help in finding the test mode for your phone. Always make sure the person
inside the building gives the signal time to arrive and register on the phone
(between 10-30 seconds for phone to reset to the signal reading).
Signal Strength Graph
EXCELLENT
E
EX
XCE
XC
CEL
ELLENT
-50dB
-60dB
60
0dB
G
GOOD
OO
-70dB
70dB
-80dB
0dB
POOR
O R
-90dB
0d
-100dB
00
N
NO
SIGNAL
G L
-110dB
0d
Signal readings usually appear as a negative number (for example, -86). The closer
you get to zero the stronger the signal (see graph below).
9
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
CORRECT INSTALLATION
INCORRECT INSTALLATION
Point antennas away from each other
Inside Panel
Antenna
Never point antennas toward each other
Inside Panel
Antenna
Outdoor
Antenna
Signal Booster
Signal Booster
Figure 1
Figure 2
Understanding the Signal Booster Light and
Troubleshooting
The Signal Booster is equipped with one indicator light labeled “Mode”. The
Signal Booster will do one of the following 3 things:
Mode
Wil
This Signal Booster is supplied with separate uplink and downlink gain controls.
Note: Reset the Signal Booster by disconnecting and reconnecting the power
supply from the Signal Booster.
Note: All red lights must be resolved before orange lights.
1. GREEN
The indicator lights on the Signal Booster will be a green if the unit is powered
up and working properly.
2. ORANGE
The Signal Booster is experiencing receiver overload. The Signal Booster has
protection circuits to prevent the disruption of cell towers. If one or more of the
lights are orange, this indicates that the Signal Booster has automatically
reduced the gain due to close proximity to a cell tower. To view how much the
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
10
gain has been reduced, turn the knob down until the light turns green. This
is the Actual Gain that the Signal Booster is operating on. Since the Signal
Booster adjusts gain automatically, there is no need to turn the gain down. If the
gain is not adequate for good coverage, you will need to turn the gain to
maximum and then turn the Outside Antenna away from the cell tower until the
lights turn to green. If the Signal Booster will not respond, turn the gain down
5 dB and then turn the Outside Antenna away from the cell tower. Continue
to adjust the gain and the antenna position until the light turns green. Contact
Wilson Electronics Technical Support Team for assistance.
3. RED
If any of the lights on the Signal Booster are red, it is indicating the Signal
Booster has shut down to prevent an oscillation, most likely caused by
the Inside and Outside Antennas being physically too close to each other.
Without this patented protection, oscillations could be transmitted to the cell
tower, blocking calls to and from the cell tower. Oscillation occurs just like
in an audio system when you put a microphone next to a speaker and get
a big squeal. When the Inside Antenna is too close to the Outside Antenna,
the same type of oscillation occurs. If the Signal Booster has a red light, the
following steps need to be done for each affected band.
First, check the Signal Booster by unplugging the power supply and
removing the coax cables from the Signal Booster. Adjust the gain to
minimum and plug the Signal Booster back in. You should now have a green
light. If not, contact Wilson Electronics Technical Support Team.
If your lights are green then unplug the Signal Booster, reconnect the coax
cables and ensure all connections are tight. Plug the Signal Booster back in.
Increase the gain until you get a red light (for example, it may be at 50 dB
for the red light) then decrease the gain until you get a green light. If your
coverage is sufficient then you are done. If not, you will need to separate
the Inside and Outside antennas further apart. Separating the antennas is
very important to get the necessary gain for the system to provide maximum
coverage and a green light.
The Outside Antenna needs to be pointed at the cell tower with its back
facing towards the Inside Antenna (refer to Figures 1 & 2 on page 10).
Without proper orientation of the antennas, you will not be able to get the
maximum gain from the Signal Booster.
*Note: If the antennas cannot be sufficiently separated, the Signal Booster will
have to operate with reduced coverage by decreasing the gain until a green
light is obtained.
11
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
Warnings and Recommendations
Warning: The Directional Antenna must always be located so the back or
side points to the Inside Antenna. Never point the front of the
Outside Antenna toward the Inside Antenna – this is to prevent
oscillation.
Warning: Connecting the Signal Booster directly to the cell phone with use of
an adapter will damage the cell phone.
Warning: Use only the power supply provided. Use of a non-Wilson
Electronics product may damage your equipment.
Warning: RF Safety: FCC rules limit radiated power of Signal Boosters to
1 watt EiRP in the 1710-1750 MHz band. In order to meet this
requirement, the gain of any Outside Antenna used with this Signal
Booster must be offset by cable loss such that antenna gain less
cable loss does not exceed 2 dBi. The Outside Antenna must be
located at least 8 inches from all people and be installed no higher
than 10 meters (32’9”) above ground. The Inside Antenna gain less
cable loss may not exceed 13.2 dBi, and it must be located at least
8 inches from all people.
Warning: Verify that both the Outside Antenna and the Inside Antenna are
connected to the Signal Booster before powering up the Signal
Booster.
Recommendation: Lightning Surge Protection is recommended for all
in-building installations.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference and (2)
this device must accept any interference received, including interference that may
cause undesired operation. Changes or modifications made that are not expressly
approved by Wilson Electronics could void authority to operate this equipment.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
12
About Wilson Electronics
Wilson Electronics, LLC has been a leader in the wireless communications industry
for over 40 years. The company designs and manufactures Signal Boosters,
Antennas and related components that significantly improve cellular phone signal
reception and transmission in a wide variety of applications, mobile (marine, RV,
vehicles) and in-building (home, office, machine to machine).
With extensive experience in antenna and Signal Booster research and design, the
company’s engineering team uses a state-of-the-art testing laboratory, including
an anechoic chamber and network analyzers, to fine-tune antenna designs and
performance. For its Signal Boosters, Wilson Electronics uses a double electrically
shielded RF enclosure and cell tower simulators for compliance testing.
Wilson Electronics Signal Boosters feature patented Smart Technology ™ that
enables them to automatically adjust their power based on cell tower requirements.
By detecting and preventing oscillation (feedback), signal overload and interference
with other users, these Smart Technology ™ Signal Boosters improve network cell
phone areas without compromising carrier systems.
All products are engineered and assembled in the company’s 100,000-square-foot
headquarters in St. George, Utah. Wilson Electronics has product dealers in all 50
states as well as in countries around the world.
13
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronics 30-day money-back
guarantee. If for any reason the performance of any product is not acceptable, simply
return the product directly to the reseller with a dated proof of purchase.
2-Year Warranty
Wilson Electronics Signal Boosters are warranted for two (2) years against defects in
workmanship and/or materials. Warranty cases may be resolved by returning the product
directly to the reseller with a dated proof of purchase.
Signal Boosters may also be returned directly to the manufacturer at the consumer’s
expense, with a dated proof of purchase and a Returned Material Authorization (RMA)
number supplied by Wilson Electronics. Wilson Electronics shall, at its option, either repair
or replace the product. Wilson Electronics will pay for delivery of the repaired or replaced
product back to the original consumer if located within the continental U.S.
This warranty does not apply to any Signal Booster determined by Wilson Electronics to
have been subjected to misuse, abuse, neglect, or mishandling that alters or damages
physical or electronic properties.
Failure to use a surge protected AC Power Strip with at least a 1000 Joule rating will void
your warranty.
RMA numbers may be obtained by contacting Technical Support at 866-294-1660.
Disclaimer : The information provided by Wilson Electronics, LLC is believed to be
complete and accurate. However, no responsibility is assumed by Wilson Electronics,
LLC for any business or personal losses arising from its use, or for any infringements of
patents or other rights of third parties that may result from its use.
Copyright © 2013 Wilson Electronics, LLC All rights reserved.
One or more of the following U.S. Patent numbers may apply to the Signal Booster in this
product – 7,729,669; 7,486,929; 7,409,186; 7,783,318; 7,221,967
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Mon.- Fri. Hours: 7 am to 6 pm MST.
14
AWS 70 Specifications
AWS 70 Specifications
Model Number
272365
Antenna connectors
N-Female
Antenna impedance
50 ohms
Dimensions
5.7 x 4.2 x 1.5 inch (14.0 x 10.8 x 3.9 cm)
Weight
1.27 lbs (0.544 kg)
1710-1755 MHz uplink
2110-2155 MHz downlink
Frequency
1
Passband Gain (nominal)
65 dB Typical,
70 dB Maximum
1700 MHz - 2100 MHz
2
3
4
20 dB Bandwidth (nominal)
1700 MHz Band
85 MHz
2100 MHz Band
91 MHz
Maximum power output for
single cellular device (uplink)
Power Output
LTE
27.9 dBm
22.0 dBm
WCDMA
26.1 dBm
21.7 dBm
HSDPA
26.0 dBm
21.7 dBm
HSUPA
26.0 dBm
21.6 dBm
Power output for multiple channels
The maximum power is reduced
by the number of channels:
Noise Figure (typical downlink/uplink)
Isolation
Maximum power output
for single received
channel (downlink)
Maximum Power
Number of channels
1700 MHz Band
(uplink)
2100 MHz Band
(downlink)
2
18.4 dBm
23.6 dBm
3
18.3 dBm
18.3 dBm
4
12.3 dBm
17.6 dBm
5
10.4 dBm
15.7 dBm
6
8.8 dBm
14.1 dBm
3.5 dB nominal
> 90 dB
Power Requirements
110-240 V AC, 50-60 Hz, 8 W
Notes:
1. Nominal gain is the maximum gain at any frequency in the passband.
2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is
20 dB lower than the passband amplification. One of the frequencies is lower than the passband and the other is higher.
3. The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier
signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and
can cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction
and not by an attenuator at the output of the device.
4. The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled.
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
or email at: [email protected]
Phone: 866-294-1660 Local: 435-673-5021 Fax: 435-656-2432
www.twitter.com/WilsonCellular
www.facebook.com/WilsonCellular
110998_Rev04_06.20.13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement