advertisement
IEM 100
UHF wireless system user manual
Musikhaus Thomann e.K.
Treppendorf 30
96138 Burgebrach
Germany
Telephone: +49 (0) 9546 9223-0
E-mail: [email protected]
Internet: www.thomann.de
23.02.2015, ID: 269815
Table of contents
Table of contents
IEM 100
3
Table of contents
UHF wireless system
4
General notes
1 General notes
Symbols and signal words
This user manual contains important information on safe operation of the device. Read and follow all safety notes and all instructions. Save this manual for future reference. Make sure that it is available to all persons using this device. If you sell the device to other users, be sure that they also receive this manual.
Our products are subject to a process of continuous development. We therefore reserve the right to make changes without notice.
This section provides an overview of the symbols and signal words used in this user manual.
IEM 100
5
General notes
Signal word
DANGER!
CAUTION!
NOTICE!
Warning signs
Meaning
This combination of symbol and signal word indicates an immediate dangerous situation that will result in death or serious injury if it is not avoided.
This combination of symbol and signal word indicates a pos‐ sible dangerous situation that can result in minor injury if it is not avoided.
This combination of symbol and signal word indicates a pos‐ sible dangerous situation that can result in material and environmental damage if it is not avoided.
Type of danger
Warning – danger zone.
UHF wireless system
6
Safety instructions
2 Safety instructions
Intended use
This device is intended to be used for the wireless transmission of audio signals to earplugs.
Use the device only as described in this user manual. Any other use or use under other oper‐ ating conditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.
This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety.
Safety
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and choke!
Never let children unattended use electrical devices.
IEM 100
7
Safety instructions
CAUTION!
Possible hearing impairment
The use of earphones at high volume over a longer period of time can cause per‐ manent hearing damage.
Adjust the output volume of your audio device to a medium value and use the earphones no longer than about one hour a day.
NOTICE!
Operating conditions
This device has been designed for indoor use only. To prevent damage, never expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt, and strong vibrations.
UHF wireless system
8
Safety instructions
NOTICE!
External power supply
The device is powered by an external power supply. Before connecting the external power supply, ensure that the input voltage (AC outlet) matches the voltage rating of the device and that the AC outlet is protected by a residual cur‐ rent circuit breaker. Failure to do so could result in damage to the device and pos‐ sibly the user.
Unplug the external power supply before electrical storms occur and when the device is unused for long periods of time to reduce the risk of electric shock or fire.
NOTICE!
Risk of fire due to incorrect polarity
Incorrectly inserted batteries may destroy the device or the batteries.
Ensure that proper polarity is observed when inserting batteries.
IEM 100
9
Safety instructions
NOTICE!
Possible damage by leaking batteries
Leaking batteries can cause permanent damage to the device.
Take batteries out of the device if it is not going to be used for a longer period.
UHF wireless system
10
Features and scope of delivery
3 Features and scope of delivery
The UHF wireless system IEM 100 is suitable for use as in-ear monitoring system especially for professional events, on rock stages and concert halls, theatres and musicals.
IEM 100
11
Features and scope of delivery
the t.bone IEM 100 770 MHz
(item no. 269815)
Your UHF wireless system IEM 100 consists of the following components: n
9.5" stereo transmitter IEM 100 ST
– Very high sensitivity at very high signal-to-noise ratio
– Input: 2 × XLR/1/4" phone combo socket
– Headphones outlet (1/4" phone socket) with volume control
– Mounting option for two transmitters side by side in a 19" rack
– Operating voltage supply: DC 12 V n
Bodypack receiver IEM 100 R
– Earplug outlet (1/8" mini phone socket) with volume control
– Operating voltage supply: 2 × AA cells (LR6, 1.5 V) n Earplugs EP 3
Ten systems can be operated simultaneously. The system operates within a frequency range of
768.000 MHz to 787.275 MHz, divided into 10 frequency groups. The frequency range is intended for use in Germany with regard to LTE.
Included accessories: 12V AC adapter, mounting hardware for rack mounting, antenna-con‐ verter and plastic case.
UHF wireless system
12
the t.bone IEM 100 800 MHz
(item no. 137618)
Features and scope of delivery
Your UHF wireless system IEM 100 consists of the following components: n
9.5" stereo transmitter IEM 100 ST
– Very high sensitivity at very high signal-to-noise ratio
– Input: 2 × XLR/1/4" phone combo socket
– Headphones outlet (1/4" phone socket) with volume control
– Mounting option for two transmitters side by side in a 19" rack
– Operating voltage supply: DC 12 V n
Bodypack receiver IEM 100 R
– Earplug outlet (1/8" mini phone socket) with volume control
– Operating voltage supply: 2 × AA cells (LR6, 1.5 V) n Earplugs EP 3
Ten systems can be operated simultaneously. The system operates within a frequency range of
791.850 MHz to 813.225 MHz, divided into 10 frequency groups.
Included accessories: 12V AC adapter, mounting hardware for rack mounting, antenna-con‐ verter and plastic case.
IEM 100
13
Features and scope of delivery
the t.bone IEM 100 863 MHz
(item no. 137793)
Your UHF wireless system IEM 100 consists of the following components: n
9.5" stereo transmitter IEM 100 ST
– Very high sensitivity at very high signal-to-noise ratio
– Input: 2 × XLR/1/4" phone combo socket
– Headphones outlet (1/4" phone socket) with volume control
– Mounting option for two transmitters side by side in a 19" rack
– Operating voltage supply: DC 12 V n
Bodypack receiver IEM 100 R
– Earplug outlet (1/8" mini phone socket) with volume control
– Operating voltage supply: 2 × AA cells (LR6, 1.5 V) n Earplugs EP 3
Four systems can be operated simultaneously. The system operates within a frequency range of 863.1 MHz to 864.4 MHz.
Included accessories: 12V AC adapter, mounting hardware for rack mounting, antenna-con‐ verter and plastic case.
UHF wireless system
14
Installation and starting up
4 Installation and starting up
4.1 General information
Unpack and carefully check that there is no transportation damage before using the unit. Keep the equipment packaging. To fully protect the device against vibration, dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage, respectively.
Establish all connections as long as the unit is switched off. Use the shortest possible highquality cables for all connections.
IEM 100
15
Installation and starting up
Notes on wireless transmission
n This device utilizes frequencies that are not harmonized within the European Union (EU) and therefore may only be used in certain EU member states. In all European countries, the frequencies used for the transmission of audio signals are strictly regulated. Before you start, make sure the frequencies are allowed in the respective country and check whether the operation must be reported to the appropriate authority.
n
Make sure that transmitter and receiver are both tuned to the same channel.
n
Never set multiple transmitters to the same channel.
n
Make sure that there are no metal objects between the transmitter and receiver.
n
Avoid interference from other radio or in-ear systems.
UHF wireless system
16
Installation and starting up
4.2 Transmitter
XLR connections for signal input on the transmitter
XLR/1/4" combo sockets for signal input on the transmitter. Drawing and table indicate the
XLR pin assignment (balanced wiring) as well as the pin assignment of a suitable 1/4" phone plug.
1
2
3
Ground, shielding
Positive signal (+)
Negative signal (–)
IEM 100
17
Installation and starting up
1
2
Signal
Ground, shielding
Phone socket for headphones outlet
Drawing and table indicate the pin assignment of a 1/4" TRS phone plug to be used.
1
2
3
Signal (left)
Signal (right)
Ground, shielding
Rack mounting
The unit has been designed for rack mounting in a standard 19-inch rack; it occupies one rack unit.
UHF wireless system
18
Connecting the operating supply voltage
Installation and starting up
NOTICE!
External power supply
The device is powered by an external power supply. Before connecting the external power supply, ensure that the input voltage (AC outlet) matches the voltage rating of the device and that the AC outlet is protected by a residual cur‐ rent circuit breaker. Failure to do so could result in damage to the device and pos‐ sibly the user.
Unplug the external power supply before electrical storms occur and when the device is unused for long periods of time to reduce the risk of electric shock or fire.
First, connect the power adapter to the transmitter and then plug the adapter into a mains wall outlet.
IEM 100
19
Installation and starting up
Mounting the antenna
Attach the included antenna to the back of the transmitter. To improve the transmission quality and for adaptation to the specific spatial conditions the antenna can be rotated and swivelled.
If there is not enough space for the direct mounting of the antenna on the unit, e.g. due to limited space in the rack, you can use the supplied coaxial cable to mount the antenna apart from the unit. Therefore use the BNC adapter.
Putting the audio connection into operation
Connect the audio inputs of the transmitter to suitable line outputs of your mixing console or amplifier. Slide the level adjustment switch (11) to the ‘–12 dB’ position. Set the input sensi‐ tivity control (2) to a middle position first.
To achieve best sound quality, a fine adjustment of this control may be required. If the input level is too low slide the level adjustment switch (11) to the ‘0 dB’ position.
4.3 Receiver
Inserting batteries into the receiver
Press on the snap-in locks at the side to open the battery compartment (18). Flip the lid open and insert the batteries respecting the correct polarity. Close the battery compartment and switch the transmitter on. The ‘RF’ LED (22) briefly lights up.
UHF wireless system
20
Installation and starting up
4.4 Taking the system into operation
n
Make sure that the receiver is switched off, the main switch (14) is set to the ‘OFF’ position.
n
Attach the receiver with the clip to your belt or guitar strap.
n
Insert the earplugs into the ear canal carefully and observe the markings ‘L’ and ‘R’ for left and right sides.
n
Turn the transmitter and the receiver on and test the transmission. Make sure that both transmitter and receiver are set to the same frequency group and the same channel. If nec‐ essary, adjust the volume on the receiver, the input sensitivity of the transmitter and the levels on your mixer or amp.
IEM 100
21
Components and functions
5 Components and functions
5.1 Transmitter
Front panel of the transmitter
UHF wireless system
22
Components and functions
1 POWER
Main switch to turn the device on or off. For turning on, keep this button pressed for one second.
2 INPUT LEVEL
Control for adjusting the input sensitivity.
3 Display
4 SET
Enter button for menu control.
5
/
Buttons for increasing / decreasing the currently indicated value.
6 PHONES
Headphones socket.
7 VOLUME
Headphones volume control.
IEM 100
23
Components and functions
Rear panel of the transmitter
24
UHF wireless system
Components and functions
8 DC INPUT
Connect the cable of the supplied mains adapter to this socket. If using another power adapter make sure it provides the correct voltage, plug polarity and sufficient power.
9, 10 LEFT INPUT / RIGHT INPUT
XLR/1/4" combo sockets (left and right channel) for the direct connection to a mixing console or another audio device that is used as signal source.
11 PAD
Level adjustment switch. Set this switch to the ‘–12 dB’ position to attenuate the input signals by 12 dB. In ‘0 dB‘ posi‐ tion, there is no attenuation.
Beneath, you find the indication of the frequency range, in which the unit operates. The specification here must match the specification on the rear side of the receiver.
12 ANTENNA
BNC mounting socket for the supplied UHF antenna. Make sure the frequency indicated on the antenna matches the frequency range indicated on the transmitter.
IEM 100
25
Components and functions
Display of the transmitter
A Limiter
Indicates limiter action as protection against volume peaks.
B Stereo/Mono
Indicates the selected operating mode (stereo or mono).
C Level indicator for left and right channel.
D
Indicates that the unit is locked to prevent unintentional operation.
E Indicates the frequency that is assigned to the set combination of frequency group
and channel (Ä Chapter 8.3 ‘Frequency charts’ on page 43).
F CHANNEL
Shows the selected channel.
G GROUP
Shows the selected frequency group.
UHF wireless system
26
5.2 Receiver
Front panel of the receiver
Components and functions
13 Flexible antenna.
14 ON/OFF/MAX
Main switch and volume control. Turn this knob clockwise past the point of resist‐ ance to turn on the receiver. Turn it further to increase the volume.
Turn this knob counter-clockwise to reduce the volume. Turn it further past the point of resistance to turn off the receiver.
15 Display
16 SET
Enter button for menu control.
17 Battery compartment for two AA cells (LR6), 1.5 V or comparable rechargeable bat‐ teries.
18 Battery compartment lid.
IEM 100
27
Components and functions
Top panel of the receiver
19 ESC
Function „Cancel/EXIT“ in the menu.
20
/
Buttons for increasing / decreasing the currently indicated value. The balance is regulated by pressing and holding the suitable key.
21 PHONES
1/8" mini phone socket (stereo) for the earplugs.
22 RF
This LED lights up on incoming radio signal.
UHF wireless system
28
Rear panel of the receiver
Components and functions
23 Indication of the frequency range in which the device operates. The specification here must match the specification printed on the back of the transmitter.
24 Clip to attach the transmitter to your belt or guitar strap.
IEM 100
29
Components and functions
Display of the receiver
H GR
Indicates the selected frequency group.
I CH
Indicates the selected channel.
J LIM
Indicates Limiter action as protection against volume peaks.
K HF
Indicates the activated high frequency boost function.
L Battery level indicator. Replace the batteries when only one bar remains displayed.
M Radio signal strength indicator (one to five bars).
N ST
Indicates an incoming stereo signal.
UHF wireless system
30
Components and functions
O
Indicates that the unit is locked to prevent unintentional operation.
P Indicates the frequency that is assigned to the set combination of frequency group
and channel (Ä Chapter 8.3 ‘Frequency charts’ on page 43).
IEM 100
31
Operating
6 Operating
6.1 Setting up the transmitter
Selecting frequency group and channel
Press the [SET] button repeatedly until the ‘GROUP’ field (frequency group) flashes in the dis‐ play. Use the ou buttons to increase or decrease the indicated value by one. When the desired value is shown press the [SET] button to confirm the setting and proceed to the next menu item.
Press the [SET] button repeatedly until the ‘CHANNEL’ field flashes in the display. Use the ou
buttons to increase or decrease the indicated value by one. When the desired value is shown press the [SET] button to confirm the setting and proceed to the next menu item.
In the lower right area, the display shows the used transmission frequency in MHz, that is
assigned to the set combination of frequency group and channel (Ä Chapter 8.3 ‘Frequency
UHF wireless system
32
Operating
Transmitter and receiver must be set to the same combination of frequency group and channel. If you use multiple wireless systems from this device family, for best results you should assign all systems to the same frequency group, but give each system a different channel.
Selecting the operating mode
Press the [SET] button repeatedly until the ‘Stereo’ or ‘Mono’ field flashes in the display. Use the ou buttons to toggle between mono and stereo operation. When the desired mode is shown, press the [SET] button for confirmation and to proceed to the next menu item.
IEM 100
33
Operating
Locking against changes
Adjusting the input level
Press the [SET] button repeatedly until ‘ON’ or ‘OFF’ and the symbol are flashing in the dis‐ play. Use the ou buttons to toggle between locked status (display = ‘ON’ ) and normal operation (display = ‘OFF’ ). In locked status, you can view the system settings, but you can't change them. In this case the display shows the symbol.
Press the [SET] button to confirm the setting and proceed to the next menu item.
The display shows the input level of the left and right channels in a bar display. Set the input sensitivity control (2) so that signal peaks reach the ‘0 dB’ marking. If the input level is still too low, slide the level adjustment switch (11) into the ‘0 dB’ position.
UHF wireless system
34
6.2 Setting up the receiver
Operating
The [SET] and [ESC] buttons that you need to set up the receiver are located behind the battery compartment lid.
IEM 100
35
Operating
Selecting frequency group and channel
Press the [SET] button repeatedly until the ‘GROUP’ field (frequency group) flashes in the dis‐ play. Use the ou buttons to increase or decrease the indicated value by one. When the desired value is shown press the [SET] button to confirm the setting and proceed to the next menu item. Press [ESC] to confirm the setting and exit the menu.
Press the [SET] button repeatedly until the ‘CHANNEL’ field flashes in the display. Use the ou
buttons to increase or decrease the indicated value by one. When the desired value is shown press the [SET] button to confirm the setting and proceed to the next menu item. Press [ESC] to confirm the setting and exit the menu.
In the lower area, the display shows the used transmission frequency in MHz, that is assigned
to the set combination of frequency group and channel (Ä Chapter 8.3 ‘Frequency charts’
Transmitter and receiver must be set to the same combination of frequency group and channel. If you use multiple wireless systems from this device family, for best results you should assign all systems to the same frequency group, but give each system a different channel.
UHF wireless system
36
Turning on the treble boost
Operating
Press the [SET] button repeatedly until ‘ON’ or ‘OFF’ and the ‘HF’ field are flashing in the dis‐ play. Use the ou button to turn the treble boost function on or off (display = ‘ON’ or
‘OFF’ ). If this function is enabled, the frequencies above 10 kHz are boosted by 6 dB and the display shows the ‘HF’ field. If the function is disabled, there's no treble boost.
Press the [SET] button to confirm the setting and proceed to the next menu item. Press [ESC] to confirm the setting and exit the menu.
Locking the settings
Press the [SET] button repeatedly until ‘ON’ or ‘OFF’ and the symbol are flashing in the dis‐ play. Use the ou buttons to toggle between locked status (display = ‘ON’ ) and normal operation (display = ‘OFF’ ). In locked status, you can view the system settings, but you can't change them. In this case the display shows the symbol.
Press the [SET] button to confirm the setting and proceed to the next menu item. Press [ESC] to confirm the setting and exit the menu.
IEM 100
37
Troubleshooting
7 Troubleshooting
In the following we list a few common problems that may occur during operation. We give you some suggestions for easy troubleshooting:
38
UHF wireless system
Symptom
No sound
Transmission is interrupted.
Troubleshooting
Remedy
1. Check the power supply of the transmitter and receiver.
2. Make sure that both transmitter and receiver operate in the same frequency range and that the transmitting antenna is designed for this frequency range.
The frequency range is stated on the devices.
3. Are both transmitter and receiver set to the same frequency group and the same channel?
4. Check the connection between the transmitter and the connected audio device (amp, mixer). Is the connected audio device switched on and does the output signal level of the audio device match the input sensitivity of the trans‐ mitter?
5. Try to improve the transmission by moving the receiver closer to the trans‐ mitter.
6. Make sure that no metal objects near the transmitter or receiver obstruct the transmission.
1. Modify the orientation of the antennas.
IEM 100
39
Troubleshooting
Symptom
The sound is distorted.
Remedy
2. If you use more than one wireless system at the same time, check the used frequency groups and channels.
3. Interference can also be caused by televisions, radios or mobile phones.
Change the ‘INPUT LEVEL’ control setting on the transmitter.
If the procedures recommended above do not succeed, please contact our Service Center. You can find the contact information at www.thomann.de.
UHF wireless system
40
8 Technical specifications
8.1 Transmitter
Input
Headphones output
Modulation type
Transmission level
Input impedance
Maximum audio input level
Gain range
NF frequency response
THD
Dynamic range
2 × XLR / 1/4" phone combo socket (balanced)
1/4" phone socket (stereo)
Frequency modulation (FM)
10 dBm
100 kΩ
+12 dBV
40 dB
60 Hz…16 kHz (
±3 dB)
< 1 % @ 1 kHz
> 90 dB (A-weighted)
Technical specifications
IEM 100
41
Technical specifications
Operating voltage supply
Dimensions (W × D × H, without antenna)
Weight
DC 12…18 V , 300 mA, via supplied power adapter
212 mm × 160 mm × 44 mm
960 g
8.2 Receiver
Modulation type
Image rejection
Sensitivity
Audio output level
Operating voltage supply
Dimensions (W × D × H, without antenna)
Weight (without batteries)
Frequency modulation (FM)
> 55 dB
–94 dBm @ 30 dB SINAD, typical
100 mW
2 × AA cell (LR6, 1.5 V)
105 mm × 23 mm × 64 mm
100 g
UHF wireless system
42
Technical specifications
8.3 Frequency charts
the t.bone IEM 100 770 MHz (Item no. 269815)
Frequency group 1
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
768.000 MHz 768.625 MHz 768.975 MHz 769.350 MHz 770.175 MHz 771.125 MHz 772.725 MHz 773.375 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
774.525 MHz 775.075 MHz 777.050 MHz 778.675 MHz 780.100 MHz 783.325 MHz 784.175 MHz 787.950 MHz
Frequency group 2
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
768.125 MHz 769.875 MHz 770.300 MHz 771.250 MHz 772.250 MHz 773.500 MHz 774.650 MHz 775.200 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
777.175 MHz 778.800 MHz 780.225 MHz 781.400 MHz 783.450 MHz 785.475 MHz 786.375 MHz 787.700 MHz
IEM 100
43
Technical specifications
the t.bone IEM 100 770 MHz (Item no. 269815)
Frequency group 3
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
768.425 MHz 769.775 MHz 770.600 MHz 771.050 MHz 772.075 MHz 773.150 MHz 774.950 MHz 775.500 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
776.250 MHz 777.475 MHz 779.100 MHz 780.525 MHz 781.700 MHz 783.750 MHz 785.775 MHz 786.675 MHz
Frequency group 4
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
768.850 MHz 769.825 MHz 770.600 MHz 771.975 MHz 772.500 MHz 772.975 MHz 773.575 MHz 774.225 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
775.375 MHz 776.675 MHz 777.900 MHz 779.525 MHz 781.200 MHz 783.900 MHz 784.475 MHz 786.900 MHz
UHF wireless system
44
Technical specifications
the t.bone IEM 100 770 MHz (Item no. 269815)
Frequency group 5
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
769.125 MHz 769.750 MHz 770.475 MHz 771.300 MHz 772.250 MHz 773.850 MHz 774.500 MHz 775.650 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
776.200 MHz 776.950 MHz 778.175 MHz 779.800 MHz 781.475 MHz 783.325 MHz 784.175 MHz 787.175 MHz
Frequency group 6
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
769.450 MHz 770.075 MHz 770.800 MHz 771.625 MHz 772.075 MHz 773.575 MHz 774.825 MHz 775.975 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
776.525 MHz 777.275 MHz 778.500 MHz 780.125 MHz 781.550 MHz 782.725 MHz 784.775 MHz 785.625 MHz
IEM 100
45
Technical specifications
the t.bone IEM 100 770 MHz (Item no. 269815)
Frequency group 7
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
769.625 MHz 770.975 MHz 771.375 MHz 772.250 MHz 773.275 MHz 774.350 MHz 775.000 MHz 776.150 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
777.450 MHz 778.675 MHz 780.300 MHz 781.725 MHz 782.900 MHz 784.950 MHz 785.800 MHz 787.875 MHz
Frequency group 8
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
769.825 MHz 770.800 MHz 771.175 MHz 772.000 MHz 773.950 MHz 774.550 MHz 775.200 MHz 776.900 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
777.650 MHz 778.875 MHz 780.500 MHz 781.925 MHz 783.100 MHz 785.375 MHz 786.900 MHz 787.600 MHz
UHF wireless system
46
Technical specifications
the t.bone IEM 100 770 MHz (Item no. 269815)
Frequency group 9
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
770.350 MHz 771.325 MHz 772.100 MHz 773.475 MHz 774.475 MHz 775.725 MHz 776.875 MHz 777.425 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
778.175 MHz 779.400 MHz 781.025 MHz 782.700 MHz 784.750 MHz 785.600 MHz 786.775 MHz 787.675 MHz
Frequency group 10
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
770.725 MHz 771.700 MHz 772.475 MHz 773.850 MHz 774.850 MHz 775.450 MHz 776.100 MHz 777.250 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
777.800 MHz 778.550 MHz 779.775 MHz 781.850 MHz 783.025 MHz 784.425 MHz 786.350 MHz 787.275 MHz
IEM 100
47
Technical specifications
the t.bone IEM 100 800 MHz (Item no. 137618)
Frequency group 1
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
790.850 MHz 791.475 MHz 792.525 MHz 793.150 MHz 795.550 MHz 797.050 MHz 798.850 MHz 800.650 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
802.575 MHz 803.725 MHz 805.750 MHz 806.850 MHz 808.650 MHz 811.725 MHz 813.150 MHz 813.800 MHz
Frequency group 2
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
791.400 MHz 792.600 MHz 793.925 MHz 794.200 MHz 795.725 MHz 797.750 MHz 799.400 MHz 801.475 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
803.100 MHz 804.775 MHz 805.800 MHz 807.400 MHz 809.200 MHz 810.200 MHz 812.775 MHz 813.750 MHz
UHF wireless system
48
Technical specifications
the t.bone IEM 100 800 MHz (Item no. 137618)
Frequency group 3
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
790.875 MHz 791.450 MHz 792.550 MHz 793.175 MHz 795.575 MHz 797.075 MHz 798.875 MHz 801.100 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
802.550 MHz 803.700 MHz 805.775 MHz 806.875 MHz 808.625 MHz 811.700 MHz 813.175 MHz 813.775 MHz
Frequency group 4
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
792.625 MHz 793.100 MHz 793.450 MHz 793.950 MHz 795.025 MHz 797.300 MHz 799.425 MHz 800.625 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
804.800 MHz 805.250 MHz 807.475 MHz 808.550 MHz 809.975 MHz 810.325 MHz 811.600 MHz 813.300 MHz
IEM 100
49
Technical specifications
the t.bone IEM 100 800 MHz (Item no. 137618)
Frequency group 5
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
790.900 MHz 791.425 MHz 792.575 MHz 793.200 MHz 795.600 MHz 797.100 MHz 798.900 MHz 801.125 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
803.025 MHz 803.675 MHz 805.300 MHz 806.900 MHz 808.600 MHz 810.050 MHz 811.675 MHz 813.125 MHz
Frequency group 6
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
792.650 MHz 793.475 MHz 793.975 MHz 794.525 MHz 795.050 MHz 797.775 MHz 799.450 MHz 800.600 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
804.825 MHz 805.225 MHz 807.450 MHz 808.525 MHz 809.950 MHz 810.525 MHz 811.575 MHz 813.275 MHz
UHF wireless system
50
Technical specifications
the t.bone IEM 100 800 MHz (Item no. 137618)
Frequency group 7
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
790.925 MHz 793.225 MHz 794.100 MHz 795.625 MHz 797.125 MHz 798.925 MHz 801.150 MHz 802.175 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
803.050 MHz 803.650 MHz 805.275 MHz 806.925 MHz 808.575 MHz 810.025 MHz 811.650 MHz 813.100 MHz
Frequency group 8
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
794.000 MHz 794.300 MHz 794.575 MHz 795.100 MHz 796.775 MHz 797.800 MHz 800.525 MHz 802.000 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
803.600 MHz 805.200 MHz 807.425 MHz 809.125 MHz 809.950 MHz 811.550 MHz 812.800 MHz 813.250 MHz
IEM 100
51
Technical specifications
the t.bone IEM 100 800 MHz (Item no. 137618)
Frequency group 9
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
790.950 MHz 793.425 MHz 794.125 MHz 795.650 MHz 797.150 MHz 798.950 MHz 801.175 MHz 802.200 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
803.050 MHz 803.625 MHz 805.250 MHz 806.950 MHz 809.100 MHz 810.000 MHz 811.625 MHz 813.200 MHz
Frequency group 10
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
794.050 MHz 794.325 MHz 795.075 MHz 796.800 MHz 797.275 MHz 800.575 MHz 801.200 MHz 802.050 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
803.575 MHz 805.175 MHz 806.950 MHz 809.150 MHz 809.475 MHz 811.100 MHz 812.850 MHz 813.225 MHz
UHF wireless system
52
Technical specifications
the t.bone IEM 100 863 MHz (Item no. 137793)
Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
863.100 MHz 863.900 MHz 864.500 MHz 864.900 MHz 863.200 MHz 863.300 MHz 863.400 MHz 863.500 MHz
Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
863.600 MHz 863.700 MHz 863.800 MHz 864.000 MHz 864.100 MHz 864.200 MHz 864.300 MHz 864.400 MHz
IEM 100
53
Protecting the environment
9 Protecting the environment
Disposal of the packaging mate‐ rial
For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling.
Ensure that plastic bags, packaging, etc. are properly disposed of.
Do not just dispose these materials with your normal household waste, but make sure that they are fed to a recovery. Please follow the notes and markings on the packaging.
Disposal of batteries
Batteries must not be disposed of as domestic waste or thrown into fire. Dispose of the bat‐ teries according to national or local regulations regarding hazardous waste. To protect the environment, dispose of empty batteries at your retail store or at appropriate collection sites.
UHF wireless system
54
Disposal of your old device
Protecting the environment
This product is subject to the European Waste Electrical and Electronic Equipment Directive
(WEEE). Do not dispose with your normal household waste.
Dispose this device through an approved waste disposal firm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.
IEM 100
55
Notes
56
UHF wireless system
Notes
IEM 100
57
Notes
58
UHF wireless system
Musikhaus Thomann e.K. · Treppendorf 30 · 96138 Burgebrach · Germany · www.thomann.de
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement