User's Manual - JR International

User's Manual - JR International
Telephone Switch
User's
Manual
Please read this manual before using
I SO 9001:2000 Certificate
COPY RIGHT RESERVED
2 L.9 PI
TABLE OF CONTENTS
1 BRIEF INTRODUCTION & FEATURES - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
1.1 EXTERNAL CALLER ID - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
1.2 OPERATING PRINCIPLE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
1.3 PRODUCT INSTALLATION RECOMMENDATION - - - - - - - - - - - - - - - - - - - - - - - 2
1.4 MAIN FEATURES - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3
1.5 SPECIFICATIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3
1.6 LAYOUT OF THE PABX - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
1.7 CONNECTING PROCEDURES - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
2 SYSTEM PROGRAMMING - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5
2.1 GENERAL PROGRAMMING INSTRUCTIONS - - - - - - - - - - - - - - - - - - - - - - - - -
5
2.2 PASSWORD - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
2.2.1 INPUT SYSTEM PASSWORD - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
2.2.2 CHANGE THE PASSWORD - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
2.3 EXTERNAL (CO) LINE CONNECTION ASSIGNMENT - - - - - - - - - - - - - - - - - - - - - 7
2.4 RINGING EXTENSION ASSIGNMENT FOR EXTERNAL(CO) LINE - - - - - - - - - - - - - 7
2.5 EXTERNAL DIALING MODE ASSIGNMENT - - - - - - - - - - - - - - - - - - - - - - - - 8
2.5.1 EXTERNAL DIALING MODE ASSIGNMENT FOR SPECIFIC EXTENSION - - - - - - - - - - - - - - - - 8
2.5.2 DIRECT EXTERNAL DIAL MODE CLEAR - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8
2.6 ATTENDANT MODE ASSIGNMENT - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8
2.6.1 OPERATOR ATTENDANT ASSIGNMENT (DEFAULT SETTING) - - - - - - - - - - - - - - - - - - - - - - - - 8
2.6.2 AUTO ATTENDANT ASSIGNMENT WITH OUTGOING MESSAGE(OGM) - - - - - - - - - - - - - - - - 9
2.6.3 AUTO ATTENDANT ASSIGNMENT WITH OGM FOR DESIGNATED CO LINES - - - - - - - - - - - - 9
2.6.4 OPERATOR NO 1 ASSIGNMENT FOR AUTO ATTENDANT MODE - - - - - - - - - - - - - - - - - - - - - - 9
2.6.5 OPERATOR NO 2 ASSIGNMENT FOR AUTO ATTENDANT MODE - - - - - - - - - - - - - - - - - - - - - - 10
2.6.6 RECORD THE OUT GOING MESSAGE (OGM) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10
2.6.7 PLAY THE OUT GOING MESSAGE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11
2.7 INTERNAL OR EXTERNAL MUSIC ON HOLD - - - - - - - - - - - - - - - - - - - - - - - - 11
2.7.1 CONNECTING EXTERNAL MUSIC ON HOLD - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11
2.7.2 LISTEN TO INTERNAL OR EXTERNAL MUSIC ON HOLD - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
11
2.8 SELECT SYSTEM LINE BREAK TIME RANGE
FOR INTERNAL FLASH RECOGNITION - - - - - - - - - - - - - - - - - - - - - - - - - - 11
2.9 CALL RESTRICTION-CLASS ASSIGNMENT - - - - - - - - - - - - - - - - - - - - - - - 12
2.9.1 CALL RESTRICTION CLASS ASSIGNMENT FOR SPECIFIC EXTENSION - - - - - - - - - - - - - - - 12
2.9.2 CALL RESTRICTION CLASS ASSIGNMENT FOR ALL EXTENSIONS - - - - - - - - - - - - - - - - - - 12
2.9.3 CALL RESTRICTION GROUP ASSIGNMENT - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
12
2.9.4 CALL RESTRICTION GROUP ASSIGNMENT CLEAR - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 13
2.9.5 AUTHORIZED DIALING NUMBER ASSIGNMENT - - - - - - - - - - - - - - - - - - - - - - - 13
2.9.6 AUTHORIZED DIALING NUMBER ASSIGNMENT CLEAR - - - - - - - - - - - - - - - - - - - 13
2.10 RESTRICT THE LINE'S RIGHT TO USE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 13
2.10.1 ASSIGN CO LINE TO BE EXCLUSIVELY ACCESSED BY - - - - - - - - - - - - - - - - - 13
AUTHORIZED EXTENSION(S). FOR OUTGOING CALLS
2.10.2 ASSIGN EXTENSION(S) TO ACCESS ONLY A - - - - - - - - - - - - - - - - - - - - - - - 14
DESIGNATED CO LINE FOR OUTGOING CALLS
2.11 LIMITED CALL DURATION OF EXTERNAL CALL - - - - - - - - - - - - - - - - - - - - - 14
2.11.1 LIMITED CALL DURATION OF SPECIFIC EXTENSION - - - - - - - - - - - - - - - - - - - 14
2.11.2 LIMITED CALL DURATION OF SPECIFIC EXTENSION CLEAR - - - - - - - - - - - - - - 14
2.12 EXTENSION NUMBER ASSIGNMENT - - - - - - - - - - - - - - - - - - - - - - - - - - - - 15
2.12.1 CHANGE EXTENSION NUMBER - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 15
2.12.2 RESTORE THE DEFAULT EXTENSION NUMBERS - - - - - - - - - - - - - - - - - - - - 15
2.13 SYSTEM DATA DEFAULT SETTING
- - - - - - - 15
3 OPERATING INSTRUCTION
16
3.1 EXTERNAL CALL - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16
3.1.1 DIRECT EXTERNAL DIALING - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16
3.1.2 MAKE AN EXTERNAL CALL BY DIAL 0 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16
3.1.3 MAKING AN EXTERNAL CALL BY TAP THE HOOK SWITCH - - - - - - - - - - - - - - - - - 16
3.1.4 OUTGOING BY PREFERRED LINE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17
3.2 INTERNAL CALL - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18
3.2.1 UNDER DIRECT EXTERNAL DIALING MODE - - - - - - - - - - - - - - - - - - - - - - - - - 18
3.2.2 UNDER NON-DIRECT EXTERNAL DIAL MODE - - - - - - - - - - - - - - - - - - - - - - - 18
3.3 RECEIVING AN EXTERNAL CALL FROM THE CO LINE - - - - - - - - - - - - - - - - - - 18
3.3.1 OPERATOR ATTENDANT MODE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18
3.3.2 AUTO-ATTENDANT MODE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19
3.4
3.5
3.6
3.7
3.8
3.9
CALL PICK UP - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - TRANSFER AN EXTERNAL CALL TO ANOTHER EXTENSION - - - - - - - - - - - - - MAKE AN EXTERNAL CALL WITH HELP OF OPERATOR OR ASSISTANT - - - - - - PARTY CONFERENCE ( BETWEEN 2 EXTS. AND 1 CO LINE) - - - - - - - - - - - - - THE EXTERNAL CALLER IS ON HOLDING - - - - - - - - - - - - - - - - - - - - - - - - - CALL FORWARDING - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
19
19
20
20
21
21
3.10 PRIORITY ACCESS AND MONITOR RECORD - - - - - - - - - - - - - - - - - - - - - - 22
3.10.1 PRIORITY ACCESS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22
3.10.2 AUTO MONITOR RECORD (OPTIONAL) - - - - - - - - - - - - - - - - - - - - - - - - - - 22
3.11 AUTOMATIC REPORTING OF EXTENSION NUMBER - - - - - - - - - - - - - - - - - - - 22
3.12 DOOR BELL & DOOR LOCK - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 23
3.12.1 CONNECTING DOOR BELL & DOOR LOCK TO THE PABX - - - - - - - - - - - - - - - - - 23
3.12.2 RINGING EXTENSION ASSIGNMENT FOR DOOR BELL - - - - - - - - - - - - - - - - - - 23
3.13 ANSWERING THE CALL FROM THE DOOR BELL - - - - - - - - - - - - - - - - - - - - - - - - - 24
3.13.1 ANSWERING THE DOORBELL CALL - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 24
FROM A RINGING EXTENSION
3.13.2 ANSWER THE DOOR BELL FROM - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 24
ANON RINGING EXTENSION
3.14 TO OPEN THE LOCK - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 24
3.14.1 TO OPEN THE DOOR LOCK AFTER ANSWER THE DOOR BELL - - - - - - - - - - - - - - - - 24
3.14.2 TO OPEN THE DOOR LOCK REMOTELY - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 24
3.14.3 EXTENSION CALL TO DOOR BELL - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 25
3.15 POWER FAILURE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 25
3.16 MONITOR RECORDER ASSIGNMENT - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 25
3.16.1 MONITOR RECORD FUNCTION FOR SPECIFIC EXTENSION - - - - - - - - - - - - - - - - - 3.16.2 CLEAR MONITOR RECORD FUNCTION FOR ALL EXTENSIONS - - - - - - - - - - - - - - - - 3.16.3 MONITOR TO RECORD CERTAIN EXTERNAL (CO) LINE - - - - - - - - - - - - - - - - - - - - - 3.16.4 CLEAR MONITOR RECORD FUNCTION FOR ALL CO LINES - - - - - - - - - - - - - - - - - - - -
25
25
26
26
3.17 DOOR BELL & DOOR LOCK ACCESSORIES - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 26
3.17.1 DOOR BELL - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 26
3.17.2 DOOR LOCK - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 26
3.17.3 TELEPHONE RECORDER - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 26
4 MAINTENANCE & TROUBLE SHOOTING - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 27
4.1 OUTGOING CALLS CAN'T BE MADE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 27
4.2 EXTERNAL CALLS CAN'T BE RECEIVED - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 28
4.3 INTERCOM CAN'T BE MADE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 28
5 WARRANTY - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 29
WARNING
THE SYSTEM MUST BE UNLOCKED BEFORE PROGRAMMING. USE EXTENSION 801 FOR
UNLOCKING AND PROGRAMMING THE SYSTEM. THE SYSTEM WILL BE AUTO LOCKED
AFTER PLACING THE HANDSET BACK ONTO THE HOOK SWITCH.
WHEN A FAILURE OCCURS WHICH RESULTS IN THE INTERNAL PARTS BECOMING
ACCESSIBLE, DISCONNECT THE POWER SUPPLY CORD IMMEDIATELY AND
RETURN THIS UNIT TO YOUR DEALER.
DISCONNECT THE POWER BEFORE DISCONNECTING THE TELECOM CONNECTION
PRIOR TO RELOCATING THE EQUIPMENT, RECONNECT THE POWER LAST.
THE POWER SOCKET WALL OUTLET SHOULD BE LOCATED NEAR THIS EQUIPMENT
AND SHOULD BE EASILY ACCESSIBLE.
TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR ANY TYPE OF MOISTURE.
PRECAUTION
Keep the unit from heating appliances and electrical noise generating devices
such as flourescent lamps, motors and televisions. These noise sources can
interfere with the performance of the Electronic Modular Switching System.
This unit should be kept free of dust, moisture, high temperature (more than
40 C/104F) and vibration, and should not be exposed to direct sunlight.
Never attempt to insert wires, pins, etc. into the vents or other holes of this unit.
If there is any trouble, disconnect the unit from the telephone line. Plug the
telephone directly to the telephone line. If the telephone operates properly, do
not reconnect the unit to the line until the trouble has been repaired. If the
telephone does not operate properly, chance are that the trouble is in the
telephone system, and not in the unit.
Do not use benzine, thinner, or the like, or any abrasive powder to clean the
cabinet. Wipe it with a soft cloth.
1
1 BRIEF INTRODUCTION & FEATURES
PABX (Private Branch Exchange) a Telephone Exchange operated within an
organisation, used for switching calls between internal lines and PSTN lines.
This PABX is designed to provide a low cost professional telephone switching
system. Up to 6 external telephone lines and up to 32 internal extensions can
be connected.
1.1 EXTERNAL CALLER ID.
This PABX is capable of receiving external FSK or DTMF Caller ID send from
the local telephone company. In order for the Caller ID to work, the user must
subscribe to the Local Telephone Company for the service.
External Calls with telephone number of caller transferred to the internal
extensions telephone. The internal extension telephone must have DTMF
Caller ID detection capabilities.
1.2 OPERATING PRINCIPLE
1.3 PRODUCT INSTALLATION RECOMMENDATION
Caution: The Power Plug should be installed in the socket outlet which is the equipment
and easily accessible.
It is recommended to avoid installing the product in the following places:
* Avoid places, where shocks or vibrations are frequent and strong
* Avoid dusty places
* Avoid places, where water or oil may come into contact with the product
* Avoid places near high-frequency generating devices such as micro wave
ovens,sewing machines or electric welders.
* Avoid places within 2 meters of television sets
* Avoid places where the environment is hot and there is no air movement
1.4 MAIN FEATURES
Operator Attendant Mode -- allows an operator or one designated extension to answer all
incoming calls.
Auto -Attendant Mode -- allows the external caller to dial the desired extension or operator
directly according guide of OGM .
Call Transfer-- allows the extension to transfer an external call to another EXT.
Call Pick Up -- allows a non ringing extension to answer a call to another extension.
Music on Hold -- with Internal or External Source Option.
External CO Line Ringing assignment -- any extension(s) can be assigned to ring, when
there is an external call.
Change Extension Number -- any extension can be allocated any extension number in the
rang from 100 to 999.
Call Restriction -- controls what numbers an extension can dial
Limited Call Duration -- the system disconnects outgoing calls when the set time expires.
Three-way Conference -- 2 internal callers can speak to an external caller.
Internal Call -- call from one extension to another ( free of charge)
Call Forwarding -- user can program their extension to forward an external or internal call to
another telephone extension.
Voice Recorder (optional)
Door Bell and Door Opener for 108,208,308,316 (optional)
1.5 SPECIFICATIONS
1.Capacity: CO Lines: 1 to 6
Extensions: 8 to 32
2.Exterior sockets: For CO lines,extensions,door bell & door lock or voice recorder
3.Communication Paths: 7
4. Transmission Specification: Extension to extension
1.5dB;
Extension to trunk line
2.0dB;
5. Ringing Voltage: 65v/50Hz;
6. Feeding current: 48v-60v/25mA;
7. Relative unbalance against ground: 300Hz-600Hz _40dB;
600Hz-3400Hz , 46dB;
8. Dialing mode: DTMF
9. Signal tone:
CO Line: tone from local telephone company;
Internal dialing tone: 450Hz, continuous wave;
Extension echo signal: 450Hz, 1 second on and 4 seconds off;
Extension busy signal: 450Hz, 0.3 second on, 0.3 second off;
Extension confirmation signal: 450Hz, 1 second on;
Extension error signal: 450Hz, 0.3 second on, 0.3 second off ;
10. Power supply: AC220V/110V± 10%
Power consumption: <15VA
11. Operational environment: Temperature: 32F-104F(0 C-40 C);
Relative humidity -90%
3
1.6 LAYOUT OF THE PABX
Name of parts:
Led for power supply and working
state of CO lines & extensions
Power supply switch
CO line and door bell port
Extension jacks for Ext.801 to 808
Power supply jack
CO Line jacks for CO 1 to 4
Extension jacks for Ext.801 to 816
CO line jacks for CO 4, 5 & 6
Extension jacks for Ext.817 to 832
CO line jacks for 00.1, 2 & 3
Extension iacks for Ext.801 to 816
Model TC-108/208/308/408 Back View
Model TC-312/316/416 Back View
Model TC-424/432/624/632 Back View
1.7 CONNECTING PROCEDURES
1.7.1 Connect external CO lines to the corresponding CO line ports on the unit
1.7.2 Connect internal extensions according to the indicated extension positions
1.7.3 Make sure to avoid short circuit
4
2 SYSTEM PROGRAMMING
2.1 GENERAL PROGRAMMING INSTRUCTIONS
2.1.1 This system has a default factory setting. If any of the programming needs
to be changed, the user can change the setting by system programming.
2.1.2 System programming can only be performed from extension 801;
2.1.3 The user should input the password to enter the system programming.
If extension 801 is in Direct External Dial Mode, the user must dial * before
dial * 01 to enter the password.
2.1.4 Press * to start programming a system setting.
Enter the code and parameters for changing a system setting.
Press # to complete the programming of a system setting.
To correct a wrong system setting, press * to do the programming of a
system setting again. There is no need to hang up the telephone.
2.1.5 After programming a system setting, a long BEEP tone indicates that the
system setting has been successful.
A series of short BEEP tone indicates that the system setting was
unsuccessful. Please check or reset the unit.
2.1.6 EXPLANATION OF DIAGRAM
Lift up Receiver(Pick Up)
Place Handset(Hang Up)
Button(Dialing)
Tap the Hook-Switch(Flash)
Listening Audio
Indicative abstract
2.2 PASSWORD
2.2 1 INPUT SYSTEM PASSWORD
Format: * 01 abcd #
abcd = system password.
Description: Allows the user to input the password to enter into the system programming.
If the user has entered into the programming mode by password,
the user should not hang up extension 801 until all the desired
system settings have been modified, otherwise the user has to
input the password again to enter into the programming mode.
2.2.2 CHANGE THE PASSWORD
Format: * 02 ABCD #
ABCD = new password (Default password = 1234)
Description: Change old password to new password
Example: The default password is 1234 We suggest to change the password
before using the PABX.
If the user wants to change the password to 5678, the user should
input * 01 1234 # to enter the system, then input * 02 5678# to
change the password to 5678.
Suppose the user needs to change the password again to 1111,
the user should input * 01 5678 # to enter the system, then input
* 02 1111 # to change the password to 1111.
6
2.3 EXTERNAL (CO) LINE CONNECTION ASSIGNMENT
Format:
*3abcdef#
abcdef = CO line port number (Default Setting = 1 to 6)
Description: Assigns which external ( CO ) line is connected to which CO line port.
Example: The company has three external CO lines. To connect external CO line 1 to
CO line port number 1, CO line 2 to port 2 and CO line 3 to port 4.
* Normally the order to select the CO line ports is from port one to port two,
port three ... one by one. For some situations, the user could ignore one
port and jump from port three to port four.
* For the CO lines, it is recommended to connect the incoming CO lines to
the high-frequently-used CO port lines and the outgoing CO lines to the
low position CO port lines.
2.4 RINGING EXTENSION ASSIGNMENT FOR EXTERNAL(CO) LINE
Format:
* 1 m abcd #
m = CO Line port number
abcd = Last digit of extension port ( Default setting = Ext.801 to Ext.804)
Description: The user can select which extension(s) must ring, when there is an
incoming call on an external CO line
Example: Assign Ext. 802 to ring, when there is an external call on CO line 1, assign
Ext. 803 and 806 to ring, when there is an external call on CO line 2
* The CO line port must be in operator mode
* The ringing extensions can only be assigned among extensions 801 to 808
2.5 EXTERNAL DIALING MODE ASSIGNMENT
2.5.1 EXTERNAL DIALING MODE FOR SPECIFIC EXTENSION ASSIGNMENT
Format: *
8 abc n #
abc = Extension number;
n = 0 = access to CO line by dial 0 or tap the switch-shook. (Default mode is n = o)
n =1 = direct access to CO line
Description: The extension can be programmed to have access to the external CO line
by dial 0 first or by tap the Hook Switch (n=0). or to have direct access to
external CO line (n =1)
Example: Assign extension 803 to have direct access to the external CO line.
Format: *
abc
(abc = extension number)
Description: The user should dial * to make internal call when extension is
in Direct External Dial Mode;
2.5.2 DIRECT EXTERNAL DIAL MODE CLEAR
Format: * 8 000 #
Description: The extension is programmed to have access to the external CO line by .
Dial 0 first or by tap the Hook Switch.
2. 6 ATTENDANT MODE ASSIGNMENT
2.6.1 OPERATOR ATTENDANT ASSIGNMENT (DEFAULT SETTING)
Format: * 2 1 #
Description: Specific ringing extension will ring when CO line is received,
pick up the extension to answer the call.
2.6.2 AUTO ATTENDANT ASSIGNMENT WITH OUTGOING MESSAGE(OGM)
Format: * 2 0 #
Description:The external caller will hear Out Going Message, none of extensions will ring.
2.6.3 AUTO ATTENDANT ASSIGNMENT WITH OGM FOR DESIGNATED CO LINES
Format: * 2 0 m #
m = CO line port number (1-6)
Description: Assign Auto-attendant mode for certain CO lines, while other CO lines
remain in Operator-attendant Mode.
Example: Assign CO 2 to Auto-attendan, and assign remaining CO lines to operator
attendant mode.
Suggest to assign all CO lines to Operator-attendant mode
before this assignment to avoid conflicts with previous setting.
This function is not available for model 408 and 632.
2.6.4 OPERATOR NO 1 ASSIGNMENT FOR AUTO ATTENDANT MODE
Format: * 2 5 abc #
abc = extension number (Default setting = Ext. 802)
Description: Assign an extension to be Operator No 1 for Auto Attendant Mode.
When external caller dial 0, his call will be transferred to operator.
Example: Assign extension 807 to be Operator No.1
2.6.5 OPERATOR NO 2 ASSIGNMENT FOR AUTO ATTENDANT MODE
Format: * 2 6 abc #
abc = extension number (Default setting = Ext. 803)
Description: Assign an extension to be Operator No 2 for Auto Attendant Mode.
The incoming call will be auto transferred to Operator No. 2, if Operator
No.1 is busy.
Example: Assign extension 806 to be Operator No. 2
The system will select an idle extension among extension 802 to 808 to
answer the external call when both of operator extensions are busy.
2.6.6 RECORD THE OUT GOING MESSAGE (3 PIECE OGM)
Format: * 2 2 N #
N = 1 = OGM 1 = Maximum 12 seconds
N = 2 = OGM 2 = Maximum 4 seconds
N = 3 = OGM 3 = Maximum 4 seconds
Description: Allows the extension assigned as an operator or manager to record up to 3
outgoing voice message. This message is played when a external caller
EXAMPLE:
accesses the DISA feature.
OGM 1: "This is A company, For the sales division, press 812. For the service division,
press 824. To call operator, press 0 "
Description: The unit will answer the call and play an out going message. The calling
party has the option to dial the number of the internal extension directly
e.g.803 or dial 0 for the operator.
OGM 2: " We are sorry. The line is currently busy, you could dial other extension
number, if you want to call the operator, press 0 "
Description: The unit will play out going message in the case of desired extension is
busy. If the external caller does not enter any correct extension number
within a certain period, then the call will be released.
OGM 3: " We are sorry. The line is no answer, you could dial other extension number,
if you want to call the operator, press 0 "
Description: The unit will play an out going message in the case of desired extension
is no answer after the caller dial the extension number within a certain
period. If the external caller does not enter any other correct extension
number within a certain period, then the call will be released.
2.6.7 PLAY THE OUT GOING MESSAGE
Format: * 2 3 N #
N = 1 = Play OGM 1
N = 2 = Play OGM 2
N = 3 = Play OGM 3.
Description: To listen to the Out Going Message (OGM) recording and to test the quality
of the telephone.
Please refer to the schematic of Switch at the bottom of unit below:
* There is has Record switch at the bottom of the unit , you must to turn the switch
to ON before you want to record outgoing message. Please to turn the switch to
OFF after recording has been finished.
* "DU" is heard at the beginning of the record and another "DU" to end of the recording.
* There is no limit on the number of times a message can be recorded.
New message overwrite old messages.
2.7 INTERNAL OR EXTERNAL MUSIC ON HOLD
2.7.1 CONNECTING EXTERNAL MUSIC ON HOLD (Optional)
(Only available for model 208, 308, 408)
This system is integrated with internal Music On Hold. Just plug the external Music
On Hold source into the external Music On Hold jack and the system will play the
external Music On Hold instead of the internal Music On Hold.
Some external music devices may generate a tone when a radio interference appears
on the signal line or AC port respectively. Those units will revert to normal operation
when the radio interference stops.
2.7.2 LISTEN TO INTERNAL OR EXTERNAL MUSIC ON HOLD
Format: * 2 4 #
Description: Allows the user to listen to the internal or external Music On Hold melody
for a short period and to test the quality of the telephone.
2.8 SELECT SYSTEM LINE BREAK TIME RANGE FOR INTERNAL FLASH RECOGNITION
Format: *
81m#
m = 1 = 750ms
m = 2 = 1000ms
m = 4 = 1500ms
m = 5 = 2000ms
m = 3 = 1200ms
Description: When the user presses the <Flash Key> or taps the Hook Switch, the telephone.
generates a line break. If the telephone generated line break time is less or equal
to the selected system line break time range, then it is recognized as an internal
flash. If the telephone generated line break time is greater than the selected system
li ne break time range, then it is recognized as an internal line release (same as
going On-Hook)
2. 9 CALL RESTRICTION-CLASS ASSIGNMENT
2.9.1 CALL RESTRICTION CLASS ASSIGNMENT FOR SPECIFIC EXTENSION
Format: * 5 6 abc n #
abc = Extension number;
n = 0 = Permit to dial Authorized number only
n = 1 = Restricts to dial the calls in Restriction Class 1
n = 2 = Restricts to dial the calls in Restriction Class 2
n = 3 = Restricts to dial the calls in Restriction Class 3
n = 4 = Restricts to dial the calls in Restriction Class 4
n = 5 = Restricts to dial the calls in Restriction Class 5
n = 6 = Permits to dial Internal call and receive the call only
Description: Assigns the outgoing calling right for an extension.
Example: Assign Ext. 803 to class 3 (n=3), assign Ext.807 to class 6 (n=6).
2.9.2 CALL RESTRICTION CLASS ASSIGNMENT FOR ALL EXTENSIONS
Format: * 5 6 n #
n = same as paragraph 2.9.1
Description: Assigns the outgoing call right for all extensions.
Example: Assign Ext.804 and 805 to class 2 (n=2), and all other extensions to class 3
To save time, the user can set all the extensions to class 3 (n=3) first, then
assign extension 804 and 805 to class 2 (n=2)
2.9.3 CALL RESTRICTION CLASS GROUP ASSIGNMENT
Format: * 5 n abcd #
n = same as paragraph 2..1 (1 to 5)
abcd = Prefix of number t be restricted
Description: Restricts to dial the numbers that with these prefix-digits..
Example: Restricts to dial the numbers with prefix 573 and 8 that in restriction class 2.
* The restricted prefix can have a maximum of 4 digits;
*A maximum of 20 groups of restricted prefixes can be assigned to each class;
2.9.4 CALL RESTRICTION CLASS GROUP ASSIGNMENT CLEAR
Format: * 5 n #
n = same as paragraph 2.9.1 (1 to 5)
Description: The user should use ehis format to clear the previous restricted prefix
setting of class.
2.9.5 AUTHORIZED DIALING NUMBER ASSIGNMENT
Format: * 5 0 abcd #
abcd = Authorized prefix number ,maximum have FOUR digits;
Description: Assigns extensions permit to dial the numbers with these authorized prefix
digits only, other numbers that without these authorized prefix-digits are
restrict to dial.
Example: Permit Ext. to dial authorized numbers with prefix "0757" or "358"only
2.9.6 AUTHORIZED DIALING NUMBER ASSIGNMENT CLEAR
Format: * 5 0 #
Description: The user should use this format to clear the previous restricted prefix
setting of class.
2.10 RESTRICT THE LINE'S RIGHT TO USE
2. 10. 1 ASSIGN CO LINE TO BE EXCLUSIVELY ACCESSED BY
AUTHORIZED EXTENSION(S). FOR OUTGOING CALLS
Format: * 4 1 M abc #
M = CO line port number (1-6),
abc = Extension number.
Description: Assign CO line to be exclusively accessed by authorized extension(s) for
outgoing calls. Even if the CO line is free, other extensions can not access
this CO line for outgoing calls.
Example: Assign CO line 2 to be exclusively accessed by Ext. 803 and Ext. 807:
2.10.2 ASSIGN EXTENSION(S) TO ACCESS ONLY A DESIGNATED
CO LINE FOR OUTGOING CALLS
Format: *4 2 M abc #
M = line port number (1-6);
abc= extension number;
Description: Assign specify extension to use only a designated CO line for external calls.
Even if other CO lines are free, this extension can not access them for
external calls
Example: To assign extension 806 to use CO line 2 only.
2.11 LIMITED CALL DURATION OF EXTERNAL CALL
2.11.1 LIMITED CALL DURATION OF SPECIFIC EXTENSION
Format: * 9 abc mn #
abc = Extension number;
mn = Call duration that can be set from 1 minute to 99 minutes
Description: The system disconnects outgoing calls when the set time expires.
Example: Assigns Ext 805 call duration to 15 minutes;
2.11.2 LIMITED CALL DURATION OF SPECIFIC EXTENSION CLEAR
Format: * 9 abc #
abc = Extension number
Description: Permits the user to make calls without a time limit.
* The actual limited call duration has about 20seconds discrepancy from
the duration what you have been set, in order to counteract the dial time;
* The maximum call duration can be set is 99 minutes;
2.12 EXTENSION NUMBER ASSIGNMENT
2.12.1 CHANGE EXTENSION NUMBER
Format: *
7 abc ABC #
abc = Previous extension number
ABC = New extension number
Description: Allows the user to change the number of extensions;
Example: Change extension number "803" to "333", and "804" to "128"
Available extension numbers are between 100 and 999, the new extension
number cannot as the same as the current extension number.
2.12.2 RESTORE THE DEFAULT EXTENSION NUMBERS
Format: *
7 000 #
Description: We suggest to use this format to restore all extension numbers before to
change the most of extension numbers to avoid reduplicate number.
2.13 SYSTEM DATA DEFAULT SETTING
Format: * 6 000 #
Description: This will re-initialize the system-programmed, if all the programmed data is
cleared, the system will be reset, using the default settings.
This program will not restore default extension number, and do not change
the CO line connection assignment.
DEFAULT VALUES
Pass Word - - - - - - - - - - - - - - - - - - - 1234
Attendant Mode - - - - - - - - - - - - - - Operator Attendant
Ringing Extension - - - - - - - - - - - - 801 to 804
CO Line connection - - - - - - - - - - - 1 to 6
Extension numbers - - - - - - - - - - - - 801 to 832
Outward Way - - - - - - - - - - - - - - - - - Dial 0 or tap the Hook Switch
3 OPERATING INSTRUCTION
3.1 EXTERNAL CALL
An extension can be in two different modes.
When in Direct External Dial mode, the extension is connected to free external
li ne directly.
When in Non Direct Dial mode, the extension can get an external line by dial 0
or by tapping the hook-switch.
3.1.1 DIRECT EXTERNAL DIALING
Description: When in Direct External Dial mode, the extension will hear external dial
tone after lift the receiver. The external number can be dialed directly now.
The user can press the REDIAL button to redial the last dialed number.
To make an internal call, the user must lift the handset and dial * to get
internal dial tone, before dial the desired extension number.
3.1.2 MAKE AN EXTERNAL CALL BY DIAL 0
Description: Lift receiver to get internal dial tone. Dial 0 within 5 seconds to get external
dial tone, then dial the desired external number.
3.1.3 MAKING AN EXTERNAL CALL BY TAP THE HOOK SWITCH
Description: If the user prefers, and external line can be accessed by tapping the Hook
Switch.The user must lift the handset to get internal dial tone, tap the Hook
Switch to get external dial tone and then dial desired external number.
3.1.4 OUTGOING BY PREFERRED LINE
Format: # n
n = CO line port number = port No.1 to No.6
Description: A proprietary telephone user can select a desired CO line preference to
make external calls.
Example: To make an external call via 003, lift the receiver to dial # 3 in a short period.
If busy tone is heard, that informs you external CO 3 is busy.
3. 2 INTERNAL CALL
An extension can make an Internal call to another extension by lift the receiver
and dial the number of desired extension in a short time.
The user must to dial * to get internal dial tone before dial the desired extension
number if his extension is in Direct External Dial Mode.
3.2.1 UNDER DIRECT EXTERNAL DIALING MODE
Format: * + abc
abc = desired extension number
Description: You need to dial * to get internal dial tone before dial the extension number;
Example: To make an internal call to Ext.807, Ext.805 picks up the telephone to dial * 807
within a short period.
3.2.2 UNDER NON-DIRECT EXTERNAL DIAL MODE
Format: abc
abc = desired extension number
Description: An extension can make an internal call to another extension by lifting the
receiver and dial the number of the desired extension within a short period.
Example: To make an internal call to Ext.807, Ext.805 picks up the telephone to dial 807.
The ringing of an Internal call is different from the ringing of an external call.
3. 3 RECEIVING AN EXTERNAL CALL FROM THE CO LINE
3.3.1 OPERATOR ATTENDANT MODE
When an external call from the external CO line is received; assigned extensions
will ring. Lift handset of any ringing extension to answer the call. Calls can also
be answered from non-ringing extensions by using the Call Pick Up feature.
If necessary, the extension that answered the calls, can forward the call to another
extension.
3.3.2 AUTO-ATTENDANT MODE
Description: When an external call has been received from the external CO line; the
unit will answer the call and play an Out Going Message. The calling party
has the option to dial the number of the internal extension directly e.g.803
or dial 0 for the operator.
* See paragraph 2.6.6
* See paragraph 2.6.4 & 2.6.5
3.
4 CALL PICK UP
Format: # 7
Description: Allows a user of a non-ringing extension to answer a call that is ringing on
another extension.
If the extension is in Direct External Dial Mode, the user must to dial *# 7
3.5 TRANSFER AN EXTERNAL CALL TO ANOTHER EXTENSION
Format: Hook Switch + abc
abc = desired extension number
Description: Allows an extension to transfer a received external call to another extension;
Example: Ext.805 receives an external call. To transfer this call to Ext 807, Ext 805 must
tap the hook-switch to get internal dial tone, then dial 807. During the transfer,
the external caller is put on hold and receives Music on Hold. When Ext.807
lifts the receiver, the external caller is transferred, Music on Hold stops and the
conversation can resume,
There are 4 different cases when A is transfers an External call to B:
a) Ext.A doesn't hang up, Ext. B lifts the handset
Communication between A and B is established. The external caller is
put on hold with Music. Whoever hangs up (A or B), the system will
transfer the external call to the other.
b) Ext.A doesn't hang up, Ext.B doesn't answer in 25 seconds.
Ext.A will be reconnect to the external caller and Ext. B will stop ringing,
c)
Ext. A hangs up and Ext.B lifts receiver to answer external call.
d)
Ext. A hangs up, but Ext. B doesn't answer the call in 25 seconds.
The external caller will be transferred back to Ext. A. If Ext A does not
answer the call in 25 seconds or it is busy, the external call will be lost.
* The range for recognizing a Hook Switch tap generated line break as an
internal flash can be programmed from 750ms to 2000ms. The user can
press the FLASH button instead of tapping the Hook Switch.
* After tap the Hook Switch and hearing the internal dial tone, Ext.A
should dial the number of Ext.B within a short time, otherwise, Ext.A
will be reconnect to CO line.
3.6 MAKE AN EXTERNAL CALL WITH HELP OF OPERATOR OR ASSISTANT
Format: Hook-Switch + abc
abc = desired extension number
Description: The operator or assistant can initiate an external call and then transfer the
call to another extension.
Example:The operator Ext. 805 initiates an external call, then transfers the call to Ext.801
* The line break recognition time range can be programmed
by the user (See paragraph 2.8)
* After tapping the Hook Switch and hearing the internal dial tone,
the operator should dial the extension number within a short time,
otherwise, the operator will be reconnect to the external CO line.
3.7 PARTY CONFERENCE ( BETWEEN 2 EXTS. AND 1 CO LINE)
Format: Hook-switch + * + abc
abc = desired extension number
Description: Allows an extension on an external call to add another extension for a 3
Party conference call;
Example: Extension 805 is talking with CO line, and 805 wants to transfer external call
to 807 to build three parties conference
There are have two cases when Ext.A is transferring CO line call to Ext. B:
* Ext. A does not hang up, Ext.B lifts the handset to answer the call.
Ext.A, Ext. B and CO line will set up 3-parties conference. Whoever
( A or B) is hangs up, the other party will be keep connecting with CO Line.
* Ext. A does not hang up. Ext.B does not answer in 25 seconds,
A will reconnect with CO line, while B will stop ringing.
3.8 THE EXTERNAL CALLER IS ON HOLDING
Format: Hook-switch + # 99
Description: When the user is on an external conversation, a Call Waiting tone from the
Local Telephone Exchange informs the user, that there is another external
call waiting.
The user can answer the waiting external call by tapping the Hook Switch
to get internal dial tone and then by dialing # 99. That will put the first
external caller on hold and connect the user to the second external caller.
If the second external caller hangs up, the user will be reconnected to the
first external caller.
Note: The user should apply for the Call Waiting feature from the Local Telephone
Company first.
3.9 CALL FORWARDING
Format: # 0 abc
abc = extension number of destination
Description: Allows an EXT. user to transfer incoming calls automatically to another EXT.
Example: The user of Ext.805 has to go to another office (extension number is 807) for
some business. He activate Call Forwarding on his extension so that all calls
to Ext.805 are transferred to Ext.807 automatically.
To clear call forwarding assignment, the user must lift the receiver and then
replace the receiver.
The system will clear the call forwarding assignment automatically after
about four hours in the case the user forget to clear the assignment.
Nothing can be heard on assigned extension and can not carry on any other
operating until the assignment is cleared.
3.10 PRIORITY ACCESS AND MONITOR RECORD
3.10.1 PRIORITY ACCESS
Format: # 9 n
n = CO line port number =1 to 6
Description: Allows user of Ext.801 to access a certain CO line even though other
people are using that CO line.
Example; Ext 801 access CO line 3 even if CO 3 is busy.
Only extension 801 has authority of priority access.
3.10.2 AUTO MONITOR RECORD (OPTIONAL)
( THIS FEATURE IS AVAILABLE FOR MODEL 108A,208A,308A&316A ONLY)
Description: You can connect Voice Recorder with our PABX by insert the signal line of
Voice Recorder with port of Monitor on PABX, it will auto start to record
desired extension or CO line once the line is used.
3.11 AUTOMATIC REPORTING OF EXTENSION NUMBER
Format: # 81
Description: Allows the user to know extension number by listening indication tones.
Example: Input #81 on Ext.803, you can hear 8 times of continuous BEEP tone, pause
about 1.5 second, then another 10 times BEEP tone is play, pause about 1.5
second, the last 3 times of continuous BEEP tone is play. That inform you that
the extension number is 803.
Description: 10 times of continuous BEEP tone = 0
If extension is in Direct Dial Out Mode, you must to dial * + # 81.
3.12 DOOR BELL & DOOR LOCK
To meet the needs of our customers, two additional functions have been added
* TALK-BACK DOOR BELL
* ELECTRONIC CONTROLLED DOOR LOCK
3.12.1 CONNECTING DOOR BELL & DOOR LOCK TO THE PABX
Connect the head of the bell cable coming from the Door Bell & Door Lock to the
Bell Socket at the back of the PABX.
Connect the long cores of the bell cable (A&B) to the Door Bell or Mini Telephone
Connect the short cores of the bell cable (C&D) to the electronic controlled lock.
TO OPEN THE DOOR LOCK, PABX WILL SEND A 10ms PULSE OF 48V AND UP TO 4A
Please refer to the schematic below
Connect the short wires
to the wire of the Door Lock
Connect the head of the bell
cable to the Door Bell Socket
* If a Door Bell is required it should be purchased separately.
* Electronic Controlled Door Lock can be purchased from lock
shop or electronics store.
3.12.2 RINGING EXTENSION ASSIGNMENT FOR DOOR BELL
Format: * 14 abcd #
abcd = last digit of the ringing extension
Description: Assign the extensions that will ring when the door bell has been pressed.
Example: Assign Ext.802, 803 & .807 to ring when the door bell has been pressed.
Description: If a visitor presses the door bell, the Ext.802,803,& 807 will ring at the same
ti me. Any one of them can answer the door bell.
3.13 ANSWERING THE CALL FROM THE DOOR BELL
3.13.1 ANSWERING THE DOORBELL CALL FROM A RINGING EXTENSION
Format: Pick up the ringing extension
Description: A visitor on the door presses the Door Bell. The designated extension rings.
The ringing extension lifts the receiver and talks to the visitor at the door.
3.13.2 ANSWER THE DOOR BELL FROM A NON RINGING EXTENSION
Format: # 7
Description: Allows to answer Door Bell from any non-ringing extension. If the non
ringing extension is in Direct External Dial mode, the user must dial *#7
to answer the Door Bell. (Same as Call Pick Up)
3.14 TO OPEN THE LOCK
3.14.1 TO OPEN THE DOOR LOCK AFTER ANSWER THE DOOR BELL
Format: Tap the Hook Switch + # 00
Description: This is to open the door after speaking with external visitor at the door.
3.14.2 TO OPEN THE DOOR LOCK REMOTELY
Format: # 4
Description: The door can be opened by any extension at any time.
3.14.3 EXTENSION CALL TO DOOR BELL
Format: # 5
Description: Allows to call Door Bell from extension.
If the extension is in Direct External Mode, the user must dial *# 5.
3.15 POWER FAILURE
Description: In the case of power failure, the external line is automatically connected to
an internal extension. During the power failure, the user will hear dial tone
from the CO line after lift the handset and he can dial the external number now.
Model 108A, Example:
CO 1 is connected to internal extension 801
Model 208A, 616A Example: CO 1 is connected to internal extension 801
CO 2 is connected to internal extension 802
Model 308A,312A,408A,416A,424A,432A,624A,632A Example:
CO 1 is connected to internal extension 801
CO 2 is connected to internal extension 802
CO 3 is connected to internal extension 803
3.16 MONITOR RECORDER ASSIGNMENT
3.16.1 MONITOR RECORD FUNCTION FOR SPECIFIC EXTENSION
Format: * 4 3 abc n #
Abc = extension number
n= 0 = monitor record clear
n= 1 = assign to monitor record
Description: Allows Voice Recorder automatically start to record desired extension as
soon as the desired extension is used.
Example: Assign Ext.813 and Ext.817 as desired monitored record extensions.
* Any extensions can be assigned as desired monitored record extension.
* Allow only one extension can be recorded at the same time. When Ext.A
is being recorded, meanwhile, Ext.B is used, but extension.B will not be
monitored record until Ext.A is free.
3.16.2 CLEAR MONITOR RECORD FUNCTION FOR ALL EXTENSIONS
Format: * 4 3 #
Description: Allows the user to clear monitor record function for all extensions.
3.16.3 MONITOR TO RECORD CERTAIN EXTERNAL (CO) LINE
Format: * 4 4 a n #
a = CO line port number
n = 0 = monitor record clear
n = 1 = assign to monitor record
Description: Allows Voice Recorder automatically start to record desired external line
when the desired CO line has been used.
Example: Assign CO 1 and CO 3 as desired monitored record external lines, the user
must input * 44 11 # ==> input 31#, hang up after a Beep tone.
3.16.4 CLEAR MONITOR RECORD FUNCTION FOR ALL CO LINES
Format: * 4 4 #
Description: Allows the user to clear monitor record function for all CO lines
3.17 DOOR BELL & DOOR LOCK ACCESSORIES
3.17.1. DOOR BELL
Two-way communication
One-touch Calling
Night-light display
2 wire connection
Compatible with model 108A,208A,308A,316A
3.17.2.DOOR LOCK
Both Electronic Control & Manual Control
Normal Key equipped
2 wire connection
Compatible with model 108A,208A,308A,316A
3.17.3 TELEPHONE RECORDER
Auto Record when off-hookswitch
Auto Stop when on-hookswitch
Record & Play by normal tape
4 MAINTENANCE & TROUBLE SHOOTING
4.1 OUTGOING CALLS CAN'T BE MADE
* Programmed to be in no CO line mode;
* Call restriction class is 6;
* CO line has been assigned to be exclusively access line to extension;
* Extension hung up improperly;
* CPU and internal data is disorder due to unstable power.
4.2 EXTERNAL CALLS CANT BE RECEIVED
* The connection to CO line is loose;
* CO line is connected to other equipment;
* No message recording for Auto Attendant mode.
4.3 INTERCOM CANT BE MADE
* Extension hung up improperly;
* Extension number is wrong.
5 WARRANTY
WE WARRANT YOUR PRODUCT TO BE FREE FROM DEFECTS IN MATERIAL AND
WORKMANSHIP FOR ONE YEAR FROM THE DATE OF PURCHASING.
THIS WARRANTY APPLIES ONLY TO THE ORIGINAL CONSUMER PURCHASER AND
ONLY TO PRODUCTS EMPLOYED IN NORMAL USE AND SERVICE.
IF THE UNIT IS FOUND TO BE DEFECTIVE, OUR DEALER IS ONLY OBLIGATION,
TO REPAIR OR REPLACEMENT OF THE PRODUCT, WHICH NOT BEEN DAMAGED
THROUGH MISUSE, ABUSE, ACCIDENT, MODIFICATION, ALTERATION, NEGLECT
OR MISHANDLING.
THIS WARRANTY SHALL NOT APPLY TO ANY PRODUCT WHICH IS FOUND TO
HAVE BEEN IMPROPERLY INSTALLED, CON-FIGURED,OR USED IN ANY WAY NOT
IN ACCORDANCE WITH THE INSTRUCTIONS SUPPLIED WITH THIS PRODUCT.
FOR REPAIR OR REPLACEMENT, CALL FOR A RETURN AUTHORIZATION NUMBER,
THEN SEND THE DEFECTIVE UNIT TO LOCAL DEALER. YOU MUST INCLUDE A
LETTER WITH THE RETURN AUTHORIZATION NUMBER, DESCRIBING
UNAMBIGUOUSLY THE WAY IN WHICH THE PRODUCT IS DEFECTIVE ALONG
WITH A PROOF OF PURCHASE.
WE DO NOT WARRANT AND SPECIFICALLY DISCLAIMS ANY WARRANTY,
WHETHER EXPRESS OR IMPLIED, OF THE FITNESS FOR A PARTICULAR
PURPOSE OTHER THAN THE WARRANTY CONTAINED HEREIN. NO IMPLIED
WARRANTY ON THIS PRODUCT SHALL EXTEND BEYOND THE TERM OF THIS
WARRANTY UNLESS SUCH LAW OTHERWISE PROVIDES.
WE SPECIFICALLY DISCLAIMS ANY LIABILITY AND SHALL NOT BE LIABLE FOR
ANY CONSEQUENTIAL OR INCIDENTAL LOSS OR DAMAGE, INCLUDING BUT NOT
LIMITED TO DAMAGES TO ANY EQUIPMENT WITH WHICH THIS PRODUCT IS USED.
NO AGENT, REPRESENTATIVE, DEALER OR EMPLOYEE HAS THE AUTHORITY TO
INCREASE OR ALTER THE OBLIGATIONS OR TERMS OF THIS WARRANTY.
THIS WARRANTY IS ONLY VALID FOR MERCHANDISE PURCHASED DIRECTLY
FROM OUR AGENT OR DEALER.
29
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement